Rockchip

Hello, I don't know if I'm posting in the right section, if I'm wrong, please excuse me and move the topic to the correct section or tell me which section to write in. I will soon be the proud owner of a NanoPi R6S and would be happy if I could help create a working image for it. I don't have positive experience with compiling a kernel for SoC, but I can test images Regards,

I've read many tutorials and tried many tips on how to change console resolution in Armbian Ubuntu 18.04 on ROCK64 but couldn't find any solution. I'm stuck with 4K resolution and can't reconfigure it down to 1920x1080. armbian-config tool lacks such basic functionality. Is there any way to do resolution change or do I have to get 1080p monitor? It's fucked up doing such simple thing is so complicated. Wasted over 2 hours now researching and no solution yet.

I literally registered to post this complaint here. How STUPID it is to have a M.2 SATA SHARED WITH HDD1!! IT DEFEATS THE WHOLE PURPOSE OF THIS ENCLOSURE. PERIOD!!!! My mistake was that I did not know what it meant that M.2 was SHARED before I purchased this enclosure and now, I have a need to expand beyond the measly 16GB of your eMMC and I found out THE PAINFUL WAY that IT IS NOT POSSIBLE because of the shared SATA port. IT"S BEYOND FRUSTRATION. YOU CANNOT EVEN IMAGINE HOW STUPID THIS DECISION OF YOURS IS. IT JUST LITERALLY DOWNGRADED YOUR NAS FROM AN EXCELLENT ENCLOSURE TO AN OVERPRICED JUNK THAT I HAD TO WAIT FOR FOR MORE THAN 6 …

I found my Helis64 unresponsive after about a week or so. Even heartbeat LED is not blinking (permanently on). I see this repeating on the serial console [495778.879711] rcu: rcu_preempt kthread timer wakeup didn't happen for 5324533 jiffies! g9706925 f0x2 RCU_GP_WAIT_FQS(5) ->state=0x200 [495778.880747] rcu: Possible timer handling issue on cpu=3 timer-softirq=2513452 [495778.881383] rcu: rcu_preempt kthread starved for 5324534 jiffies! g9706925 f0x2 RCU_GP_WAIT_FQS(5) ->state=0x200 ->cpu=3 [495778.882336] rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior. [495778.883137] rcu: RCU grace-period kthread stack dump: [495778…

Built latest image for a Rock 3c based device and am having an issue with ethernet connectivity. Boots fine. Wifi works well and it seems functional other than Eth connectivity. My old DTB (from 4.19) will not boot , using a rock3c DTB instead to get a 90% functional device Showing the following for ethernet dmesg | grep eth [ 0.000000] psci: probing for conduit method from DT. [ 3.199039] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 3.199576] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 3.199601] rk_gmac-dwmac fe010000.ethernet: TX delay(0x30). [ 3.199614] rk_gmac-dwmac fe010000.ethernet: RX delay(0x10). [ …

Hello, I have a Rock64 V2 which I am using as a Tvheadend server, among other stuff. For some months I put the kernel/dtb packages on hold, because I discovered that linux-image-rockchip64 after version 5.75 did not include the kernel module for th USB DVB-T stick I need (an EyeTV DVB-T device, i.e. a clone of Hauppauge), that is dvb-usb-dib0700 or the like (I am trying to remember). I have recently unhold the Linux packages and let apt to update them. Now at version 5.90, I see that the kernel module is still not included, and my USB device cannot be used. Going back to Linux image 5.75 makes the stick to work again, but I'd like to have the lates…

I have previously successfully been using the USB serial gadget as terminal on the Nanopi R2S. The last working release I have tried was: Linux 5.4.45-rockchip64 #20.05.3 SMP PREEMPT Wed Jun 10 11:47:27 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux Now I am running the following version (Also tried 20.08.08) and the gadget mode does not work after boot. Linux 5.8.14-rockchip64 #20.08.10 SMP PREEMPT Tue Oct 13 16:58:01 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux I have seen no warnings or error messages when running dmesg. After boot on the failing versions the log contains the following section, which I assume means that the driver …

Anyone gets Nanopo M4 on-board bluetooth working. Any pointer would be appreciated. Here are what I did: - install Bluetooth component from armbian-config $ sudo service bluetooth status ● bluetooth.service - Bluetooth service Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset: enabled) Active: active (running) since Wed 2019-07-31 15:59:27 PDT; 9s ago Docs: man:bluetoothd(8) Main PID: 14661 (bluetoothd) Status: "Running" Tasks: 1 (limit: 4558) Memory: 2.1M CGroup: /system.slice/bluetooth.service └─14661 /usr/lib/bluetooth/bluetoothd …

Hi everyone, I have installed openmediavault and zfs. Since yesterday I have this error: Failed to execute command 'export PATH = / bin: / sbin: / usr / bin: / usr / sbin: / usr / local / bin: / usr / local / sbin; export LANG = C.UTF-8; zfs list -H -t snapshot -o name, used, refer 2> & 1 'with exit code' 1 ': The ZFS modules are not loaded. Try running '/ sbin / modprobe zfs' as root to load them. Click "show details" Error # 0: OMV \ ExecException: Failed to execute command 'export PATH = / bin: / sbin: / usr / bin: / usr / sbin: / usr / local / bin: / usr / local / sbin; export LANG = C.UTF-8; zfs list -H -t snapshot -o name, us…

Hello Folks, Good day. I hope you're doing great. I'm trying to make the OrangePI 10.1 inch MIPI DSI (product page) work on the most recent (mainline) Armbian build. Building the image using the OrangePI source repositories and following the instructions on OPi4B manual enables the LCD and touch, However, my intention is to make the LCD + Touch work on the most recent Armbian Focal (mainline). I've setup my Armbian build env but I cannot see to find how to enable this MIPI screen on any build options. Here's the instructions from Page #20 of OPi 4B manual: Download the Linux source code and make the following changes in dts --- a/arch/arm6…

RockPi4a. Installed busster current 5.8.6 armbian onto eMMC. Works fine. Now i figure out i need swap space (app needs more than the 1G mem i have). So i boot another image from SD an use gparted to shrink the first partition from the end to create 4GByte and create a swap partition in there. Now the board won't boot anymore (see attached file). Erased SPI, no difference. Partition table shows GPT and "MBR protective" (before and after resizing). so, whats the magic to create a bootable armbian disk if one needs different partitioning than just the "full disk one partition" layout ? Is this "uboot" hidden behind the only partition, there was a bun…

I've a set of Orange Pi 5 Max boards, all of them mounting fast NVME units. My plan was to use micro SD card to host the OS, but delegate all intensive writing (log, tmp) to a special partition on the NVME unit which will be used for OS and Application data (both for performance, and to extend the lifetime of the SD card). That way I can flash the OS disk as needed without worrying about flashing the data disk with it. I've seen that Armbian uses zram by default, but I'd like to keep the entire RAM available for the applications that will be running in the boards (NVME should be fast enough to not notice a massive impact vs using the RAM). As I have seen disab…

Hi there, Just got OPi4 after some problem from Chineses... Problem: - no at all output at HDMI (connected to HDMI-VGA converter and 1920x1024 VGA LCD display, works with OPi PC+), - if Eth connected device gots (after few minutes) IP from DHCP. - no server running on that IP (tried telnet, ssg, WWW), PING works. uSD card with Armbian Buster for OPi4. What to check next? Console? What speed? 115200 or 1.500.000?

I use Armbian_20.05.3_Rockpi-4a_buster_legacy_4.4.213 The armbian kernel version uses 4.4-213 Follow the radxa official installation script： curl -sL https://rock.sh/get-rockpi-penta | sudo -E bash - The output is as follows： I don’t know where the problem is after execution, I still can’t drive it.... It feels like a failure caused by the kernel, it seems that it only supports linux-image-4.4.154-110-rockchip-gcef30e88a9f5 I executed the command to install the kernel： sudo apt-get install linux-4.4-latest Something went wrong. I just started contacting SBC System and hope I …

Hi, My Nanopi M4V2 often gets unresponsive. I cannot reach the nginx server when that happens. SSH also stops working. The red led is on, and the green led stops blinking when it happens. Any tips on what I can try? Running: Armbian buster with Linux 5.4.49-rockchip64 with heatsink from EMMC. http://ix.io/2u4O

Despite this being the supported image advertised for the board, it just does not boot on this board, whereas the "current" image does boot (but with limited hardware support). I'm booting with just the serial console connected, to limit interferences On serial console with default config I get: Found U-Boot script /boot/boot.scr 3185 bytes read in 4 ms (777.3 KiB/s) ## Executing script at 00500000 Boot script loaded from mmc 1 117 bytes read in 3 ms (38.1 KiB/s) 7861795 bytes read in 361 ms (20.8 MiB/s) 20770824 bytes read in 941 ms (21.1 MiB/s) 104363 bytes read in 11 ms (9 MiB/s) 2698 bytes read in 7 ms (376 KiB/s) Applying kernel provided DT fixup…

Hello everyone, I somehow managed to brick my OrangePi 4 LTS. I had the Armbian running on it and decided to try the newest install in a minimal format so no desktop. Installed it, made all the setup and restarted. Since then no other image works, neither the official orangepi images nor any other armbian image. I tried booting off without the SD Card, trying to flash another OS with the SD card and read out the TTL and this is what I get: DDR Version 1.25 20210517 In channel 0 CS = 0 MR0=0x18 MR4=0x2 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x18 MR4=0x2 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x…

I burned the .img file via RkDevTool to eMMC according to the manual, however when I try to upload I get the following error: "Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! UUID=cff1be9d-0892... does not exist. Dropping to a shell!" blkid says: /dev/mmcblk1p1: PARTUUID="d0bc2961-01" fsck /dev/mmcblk1p1 says: error 2: no such file or directory cat /proc/cmdline says: root=cff1be9d-0892... rootwait rootfstype=ext4 splash plymouth.ignore-se…

Hello, I am working with "Armbian_21.08.1_Nanopineo4_focal_current_5.10.60" on a nanopi Neo4. During the initial boot, the (HDMI) monitor shortly displayed some text (went to fast to read) and then went blank and the monitor turned off. However, output came through the serial debug port (USB2) and I was able to complete the initial setup. Now, I can now connect with SSH, but it would be nice to be able to work directly. How can I redirect the output to the HDMI monitor? Cheers, John

I do have a setup: 2.5" disks connected to the powered USB 3.0 hub. The power adapter is 10A. If I do start rsync copy from one disk to another after a while I'm getting the error: rsync error: error in file IO (code 11) at receiver.c(393) [receiver=3.1.2] All disks disappired. There is no way to return them back, only reboot helps. In dmesg I could find that device jsut stopped and disappired: [ 2342.927583] usb 5-1.1: USB disconnect, device number 3 [ 2342.931057] usb 4-1: USB disconnect, device number 2 [ 2342.931975] usb 5-1: USB disconnect, device number 2 [ 2345.629932] usb 5-1.3: USB disconnect, device number 4 [ 2345.663838] usb 5-1.4: …

HI I just bought 2 neo3 and started with Armbian and the MAC address is the same. But using the official image is a different MAC address.How can I use Armbian so that neo3 has the correct unique MAC address? I use cmd xxd / sys / bus / nvmem / devices / rockchip-efuse0 / nvmem I get the same value.

Hello, I have an Orange Pi RK3399 and I'm very interested to install an armbian linux using the usb c instead of the usual method with the sd card. I have looked around but I was able to do it. Do you have any suggestions? Thank you very much for your help

I have a FriendlyElec 1080P HDR camera(MACM400). It only works on some FriendlyElec Release with 4.4 kernel. So how could this camera work on Armbian with Mainline kernel?

I've got an m4v2 running current armbian (Armbian_19.11.4_Nanopim4_bionic_legacy_4.4.192_desktop.7z) I get a stack of messages on tty1 and in dmesg stating "get wrong frequency". it was also logging via syslog, but I have disabled those from logging. it also seems to generate one of these messages every time I hit a key on the keyboard. somehow related to kbd interrupt? ondemand cpu freq scaling works, running cpu intensive jobs, the following frequencies were observed Jan 11 10:45:01 m4-2 root: CPUTEMP 45.00 (600.00/600.00) Jan 11 21:50:01 m4-2 root: CPUTEMP 44.44 (1416.00/600.00) Jan 11 21:55:01 m4-2 root: CPUTEMP 45.62 (1416.…

My system has: $uname -a Linux rkpi 5.8.11-rockchip64 #20.08.4 SMP PREEMPT Wed Sep 23 17:51:13 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux Sound stack seems to be loaded, but alsa/pulseaudio sees only hdmi-output device (aplay log below). How to enable analog ouput on 3.5 mm jack? $sudo aplay -lL default Playback/recording through the PulseAudio sound server null Discard all samples (playback) or generate zero samples (capture) samplerate Rate Converter Plugin Using Samplerate Library speexrate Rate Converter Plugin Using Speex Resampler jack JACK Audio Connection Kit oss Open So…

Hello everyone, I want to use uart4 port for zigbee2mqtt,but I don't know how to activates it.

Hello, I have read some threats with the same issue, armbian images are not booting, there is not HDMI signal when turn on rockpi4. General solution is trying armbian image stored on radxa server https://dl.radxa.com/rockpi/images/third-party/Armbian_5.67_Rockpi4b_Debian_stretch_default_4.4.154_desktop_20181210-gpt.img.gz this armbian version works fine but it's too old, also i'm interested to use latest armbian-ubuntu-bionic My case: I have a new rockpi4b 1.4v, not eMMC module, I have flashed several armbian versions on sdCard : https://dl.armbian.com/rockpi-4b/Bionic_legacy_desktop https://dl.armbian.com/rockpi-4b/Buster_legacy htt…

Hi, I'm new to the forums and am looking into replacing OEM Klipper firmware on a Sovol SV06 Ace, The main board looks very similar to the MKS Skipr with the following notable differences: rk3308 B emmc soldered on No SD card. Wifi/Bluetooth added - Original boards used realtek and the latest version uses Broadcom. OEM wifi is hit or miss on connecting and hopefull will be improved with Trixie based Armbian. Sovol has mostly complied with the GPL and source/configuration files are on github. IIRC the kernel version was 5.1x I'm a long time Linux user (Slackware 8.1), have contributed OpenWRT builds and hav…

SoC: Rockchip RK3568B2 CPU: Quad-core ARM Cortex-A55 CPU, up to 2.0GHz GPU: Mali-G52 1-Core-2EE，supports OpenGL ES 1.1, 2.0, and 3.2, Vulkan 1.0 and 1.1, OpenCL 2.0 Full Profile VPU: 4KP60 H.265/H.264/VP9 video decoder, 1080P60 H.264/H.265 video encoder NPU: Support 0.8T RAM: 2GB LPDDR4X Flash: 8GB eMMC Ethernet: one Native Gigabit Ethernet, and two PCIe 2.5Gbps Ethernet USB: two USB 3.2 Gen 1 Type-A ports HDMI: support HDMI1.4 and HDMI2.0 operation support up to 10 bits Deep Color modes support up to 1080p@120Hz and 4096x2304@60Hz support 3-D…

I connect the rockpi 4 to a Samsung display whose normal resolution is 1680x1050 via a hdmi to dvi line, but the maxium resolution I can choose is 1280x1024. And when I connect it to a 4K tv via hdmi, the maxium resolution is 1920x1080, not 3840x2160. The legacy kernel (4.4.210) works perfectly in both cases.

Hi, I would like to know if any support for VAMRS ROCK960 is planned. Thanks

Hi to all, after the 16GB of the eMMC is slowly reaching my limits, I installed a 128GB M.2 SSD and wanted to use the kobol tutorial to transfer the system data on it... https://wiki.kobol.io/helios64/install/transfer/#transfer-rootfs-from-emmc-to-sata-or-usb ... unfortunately I see at position 4 only /dev/md0 instead of the M.2 Sata on /dev/sda root@helios64:/dev# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 119.2G 0 disk sdb 8:16 0 3.7T 0 disk └─md0 9:0 0 7.3T 0 raid5 /srv/dev-disk-by-label-nas sdc 8:32 0 3.7T 0 disk └─md0 9:0 0 7.3T 0 raid5…

I was working with OpenHD when it was taken down by GitHub. There's something we should be concerned about here in the rockchip section of armbian? Original Post: https://github.com/github/dmca/blob/master/2025/12/2025-12-18-ffmpeg.md Identify only the specific file URLs within the repository that is infringing: https://github.com/rockchip-linux/mpp/blob/develop/mpp/codec/dec/av1/av1d_codec.h https://github.com/rockchip-linux/mpp/blob/develop/mpp/codec/dec/av1/av1d_cbs.c https://github.com/rockchip-linux/mpp/blob/develop/mpp/codec/dec/av1/av1d_cbs.h https://github.com/rockchip-linux/mpp/blob/develop/mpp/codec/dec/av1/av1d_parser2_syntax.c https…

Hi guys, I have been using my Helios64 for more than a year now. I have it connected with the 1Gbps NIC. I have been reading about network bonding and getting both NICs up and running. The main purpose would be to have it running in mode "Adaptive Transmit Load Balancing" (mode 5). First I've discovered the issue with the 2.5Gbps not being able to keep a consistent (and performant) speed. So I've soldered the missing pin from the capacitor to the NIC (more on this later). I've checked the speed and now it is up to specs, getting very close to 1000Mbps (960-980Mbps). But here it comes the problem that I'm facing, if I enable both independently …

Hello everyone! I will teach you how to install WiringOP on Armbian. It's not the most practical method, but it works. First, we download the repository from the original website. $ apt-get update $ apt-get install -y git $ git clone https://github.com/orangepi-xunlong/wiringOP.git Then, we proceed to look for the name of our board that is associated with Armbian. $ cat /etc/armbian-release | grep "BOARD=" | awk -F'=' '{print $2}' The previous command will give us the name of the board, which is the following: root@armbian:~# cat /etc/armbian-release | grep "BOARD=" | awk -F'=' '{print $2}' orangepi-r1plus-lts Now, we pro…

Hi I found the following page https://www.armbian.com/rockpi4/ but I guess those files are for rock pi 4 and not rock pi 4 c? It has a link to 4 c plus images https://fi.mirror.armbian.de/dl/rockpi-4cplus/archive/ but they only contain bullseye? So are there any plans for rockpi 4 c plus to have a bookworm image? Are there any github pipelines that build them where I could send a pull request? (not that my c or c++ compilation skills are existing but I would be happy to give it a try).

Hello. Please could someone help me to solve this issue? I have a wifi dongle recognized as: Bus 002 Device 002: ID 148f:5572 Ralink Technology, Corp. RT5572 Wireless Adapter I am trying to use it on my Rock64 and ARMBIAN 5.42 testing Debian GNU/Linux 9 (stretch) 4.4.124-rk3328 uname -a: Linux rock64 4.4.124-rk3328 #24 SMP Wed Mar 28 17:15:52 CEST 2018 aarch64 GNU/Linux It seems it is recognized correctly: Spoiler lsmod: rt2800usb 28672 0 rt2800lib 81920 1 rt2800usb rt2x00usb 20480 1 rt2800usb rt2x00lib 49152 3 rt2x00usb,rt2800lib,rt28…

Hi. My helios64 always crashes with this method : [environment] 1TB m.2 sata ssd for system 16TB seagate exos on data drive 18TB WD Ultrastar DC550 on data drive Linux helios64 5.9.14-rockchip64 #20.11.4 SMP PREEMPT Tue Dec 15 08:52:20 CET 2020 aarch64 aarch64 aarch64 GNU/Linux about 620,000 files on data drive. [method1] #sync #sysctl -w vm.drop.caches = 3 #ls -CFR [datadir] > [tmp dir] #ls -1lFR [datadir] > [tmp dir] #zip -j [tmpdir] filelist.zip #sync >>>>>>> Crash (blinking Red LED) [method2] (First step) via…

Title. I've tried installing libgl1-mesa-dri but support feels really broken (Brave crashing frequently, mismatching opengl version, etc.). Am I missing something? Thanks in advance.

Dear Forum! If you are using Emmc as boot device, a M.2-ssd as system device and OMV is installed. You can backup with the OMV given image-backup (dd, fsarchiver). But how you can restore the backup? You need to boot from Sdcard (boot and system from sd)? And after that you can switch again back to emmc-boot and ssd-system without any issue? Is there any other easier way i.e. with CloneZilla to image-backup/restore? How you can do this?

Hi, I'm using a RockPi 4 B as a wifi access point. Everything is working fine with good performances until the Wifi stop working, usually after 3-4 days. When that happens, dmesg is flooded with these logs : [221057.075187] ieee80211 phy0: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110 [221057.075202] ieee80211 phy0: brcmf_cfg80211_get_station: GET STA INFO failed, -110 [221124.657840] ieee80211 phy0: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110 [221127.217786] ieee80211 phy0: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110 [221127.217806] ieee80211 phy0: brcmf_cfg80211_get_stat…

I have a project developed on Rock 4C+ v1.2 board. Now there is only v1.41 board available and Armbian is not booting on it at all, no matter it's compiled locally, or it's downloaded from the official sources. UART debug is producing unreadable sequence. So far, what I’ve tried: - I’ve built Armbian with the latest changes armbian build repo - hasn't helped - I’ve used rk3399-rock-4c-plus.dtb file instead of rk3399-rock-pi-4c-plus.dtb, dunno why there are two, but somewhere on the forum I read that this one without “pi” is the right one - hasn't helped - official Armbian images - not booting - Ubuntu and Debian - both booting fin…

Bluetooth device does not appear on my armbian (kernel is 5.17.5-media, tried on edge-media and current-media as well). # hciconfig version Can't get device info: No such device # bluetoothctl Agent registered [bluetooth]# devices No default controller available HCI socket does not seem to be created. Got this in dmesg: [ 11.990128] Bluetooth: HCI device and connection manager initialized [ 11.990145] Bluetooth: HCI socket layer initialized [ 11.990164] Bluetooth: L2CAP socket layer initialized [ 11.990188] Bluetooth: SCO socket layer initialized [ 12.081220] Bluetooth: HCI UART driver ver 2.3 [ 12.081245] Bluetooth: HCI UART pro…

Hey guys, I installed Armbian some months ago in my Rock64 and I had never updated the packages. Yesterday I decided to do an apt update + apt upgrade to update one of the applications I use. I noticed that meanwhile apt updated Armbian itself, and began to ask for a reboot. A few hours later I rebooted the board. At first I couldn't connect due to connection refusal, so I went plugged a keyboard and hdmi on the board to see what was happening. It looks like while doing this I unplugged the power source suddenly, and now the board won't boot the system in this OS. No image or response in the USB keyboard. …

Howdy With a p2 that already had ubuntu installed on the ssd using the firefly technique, it seemed time to upgrade using to armbian. Installing the new uboot went fine. It is not clear how to confirm it. The command did not error. However using the jammy 22.08 images, the uuid does not appear to be on the SD card. At this time I do not have a serial cable. However the image shows sum of the situation. Any help appreciated including advice on rj45 to serial cable. Thanks.

Armbian version 22.05.3 Focal Nanopi M4V2 There seem to be only default modes available with the nanopiM4V2. Manual adding a resolution does not work (it is added, but has no effect when selected) NanoPIM4V2 Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 4096 x 4096 HDMI-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axi> 1920x1080 60.00* 60.00 50.00 1920x1080i 60.00 50.00 1280x1024 60.02 1280x960 60.00 1280x720 60.00 50.00 1024x768 60.00 800x600 60.32 56.25 720x576 50.00 720x480 59.94 The monitor is a …

Hi, after solving the WIFI issue on my T4, i've tried to setup an AP. With the armbian-config it was pretty easy and i only changed the channel to 1 on for the g mode and the country_code on for n mode: cat /etc/hostapd.conf # # armbian hostapd configuration example # # nl80211 mode # ssid=ARMBIAN interface=wlan0 hw_mode=g channel=1 #bridge=br0 driver=nl80211 logger_syslog=0 logger_syslog_level=0 wmm_enabled=1 wpa=2 preamble=1 wpa_psk=844418fea2e83eea256a88c751f2823c2d5e6d52193b27cfa34234e0d6de0ab9 wpa_passphrase=12345678 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP auth_algs=1 macaddr_acl=0 noscan=1 ## IEEE 802.11n ieee80211n=1 …

I have a C++ app that wants to indicate its activity by blinking an LED on the Rock64. How can the LEDs be controlled? The sysfs leds do not appear to be present. I'm okay with libgpiod or sysfs gpios, but I don't know what gpio numbers represent the LEDs. Anyone know? Thanks. Linux rocky64 5.0.0-rockchip64 #5.85 SMP Wed May 8 19:38:28 CEST 2019 aarch64 aarch64 aarch64 GNU/Linux Distributor ID: Ubuntu Description: Ubuntu 18.04.3 LTS Release: 18.04 Codename: bionic

I am starting Rock64 again after a long layoff. I'm a bit rusty, please forgive any forgetfulness. I tried downloading the Rock64 desktop image, but it was 404. I downloaded Armbian_19.11.6_Rock64_bionic_legacy_4.4.207_desktop.7z Unzipped it, and used etcher to write it to the micro-SD card. Booted up, but didn't get to a graphical desktop. Created a new user OK. I did # apt update, # apt upgrade, # reboot now. Still no graphical desktop. I did # apt install lxde lxdm. (this used to work OK). As expected, the installer asked if i wanted to use lxdm as the display manager. Yes. $ sudo armbian-config Updated the t…

Hi there, My Rock5B worked well with Armbian until I tried to migrate to an NVMe. Here is a boot log without any SDCard: Spoiler DDR Version V1.08 20220617 LPDDR4X, 2112MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB Manufacturer ID:0x6 CH0 RX Vref:31.7%, TX Vref:21.8%,21.8% CH1 RX Vref:30.7%, TX Vref:21.8%,20.8% CH2 RX Vref:31.7%, TX Vref:21.8%,21.8% CH3 RX Vref:30.7%, TX Vref:22.8%,21.…

Hi everybody, I recently set up a small server with the Rock64 booting armbian stretch 5.59 stable directly from a 120 GB SSD attached via USB3. Booting is handled with U-Boot from ayufan on the SPI flash. The Rock64 is board revision 2.0, the power supply is the original Pine64 one for the Rock. Besides the SSD, there are no other peripherals connected. The board often (3 out of 4 times) hangs when booting. In this case, all LEDs are lit, the orange network LED will flash and the board is not reachable by SSH and not pingable. My impression is, that it is stuck because the SSD either powered up too late or the USB connection is delayed. However, I…

Hi all, currently i'm working on upcoming Helios64 board. For RK3399 board there are 2 families, what are the differences between them? I've been following discussion on github and this forum for few months but still unsure which family i should use.

Hey, I am using a Nanopi M4v2 with a Satahat as server for openmediavault and plex. Since I got a lot of freezes/crashes (every 24-72h, the Nanopi lost the connection, and the green LED isn't blinking anymore) with "Armbian 20.02.7 buster current 5.4.28" on a SD-Card. I plugged a SSD in and used the nand-install script with a clean installed SD-Card. But this doesn't help, the problem is still there. The log got spamed with this: May 3 13:17:03 nanopi brcm_patchram_plus_rk3399[1338]: writing May 3 13:17:03 nanopi brcm_patchram_plus_rk3399[1338]: 01 4c fc ff 3d 01 22 00 00 0d 05 00 00 50 fb 31 May 3 13:17:03 nanopi brcm_patchram_p…

I manged to get the USB OTG headers working on the NEO3 by modifying the NanoPi R2S DTB that it is currently using. 2 changes were needed: - Replaced all usb2 references to usb0 - Changed dr_mode for usb@ff580000 from otg to peripheral Modified DTB file attached if anyone else wants to give this a try or has a need for OTG on the NEO3 rk3328-nanopi-neo3-rev00.dtb

/proc/sys/crypto doesn't exist, so anything checking the status of /proc/sys/crypto/fips_enabled fails terribly. (Specifically trying to bring up a FreeIPA server which includes tomcat-based Dogtag CA, it checks for FIPS during setup, dies). I see there is an rk_crypto kernel module available, so I don't know why /proc/sys/crypto itself is missing. I tried 'modprobe rk_crypto' and it loaded (appears in output of 'lsmod'), but /proc/sys/crypto still doesn't exist.

Is there an accepted procedure for moving from using ramlog to logging to disk? I've looked but everything I can find is about setting up ramlog. I assume it's more complicated than just creating a partition (or ZFS dataset) and mounting it /var/log, disabling ramlog, and rebooting.

I have recently bought a rockpi5 and i was looking all over the internet for a POE hat module to power it up . However i was unsuccessful so far. I have tried the poe hat i had for my rockpi 4 B but it doesn't physically fit so my question is will a POE hat for the rockpi 5 be anytime soon released ?

Hello, I've got my Helios64 since a few week now and enjoying it a lot. I've installed k3s on it with various applications. The next step is to install home assistant to control my home. Previously, I've already had a setup with a RaspberryPi with a Arduino Mega connected, that is running the rflink firmware. That way I, can control cheap 433Mhz power switches. The problem is, when I connect the Arduino (acting as a serial input device) to my Helios64, the system does not startup anymore. The following error message is printed on the serial console: WARN halted endpoint, queueing URB anyway. Unexpected XHCI event TRB, skipping... (f5f5deb…

Let's divide it into parts - Bluetooth Bluetooth isn't working. I've tried activating UART7 and GPIO pins 19 and 22, but to no avail. I installed the drivers, but to no avail. Bluetooth isn't communicating! - Audio ES8388 For some unknown reason, the ES8388 has audio disabled by default on the ASA. To fix this, simply go to the terminal and run the command user@user alsamixer Then use the buttons to move around until you find OUT1. Out1 above it says MM (mute), so click M to make it 00 with a green background. Audio problem solved - Language I can't set the language to Portuguese in the Gnom…

Hello, I have a Helio64 not yet configured and I would like to be able to install the latest image available on https://armbian.hosthatch.com/dl/helios64/archive/ and especially to install the latest OpenMediaVault 6 version. Do you think this is possible ? Or will OpenMediaVault 6 not be available from armbian-config? As I write this post, the latest image available for Helios64 is Armbian_21.05.9_Helios64_bullseye_current_5.10.63.img.xz I thank you for your help Flolm

Hey fellow tinkerers, I'm pretty happy with my Rock64 boards so far, however, when I recently upgraded the kernel on the oldest one and rebooted, I couldn't ssh back in. So I hooked it up to a monitor and was blown away from all the error-like text that kept flowing on my screen. Since I have if this is logged anywhere (I looked but couldn't find anything after mounting the sdcard in my laptop), I had to film it. See attached video. It basically consists of lots of errors formatted like this: [<ffffffxxxxxxxxxx>] and a lot of errors looking like this: dma-pl330 ff1f0000.dmac: pl330_update:1783 Unexpected! Is there any way to s…

Hi folks, long time lurker here. My helios64 is pretty much brand new, didn’t really needed it at that time, only bought it as I found it really cool. I may power it a couple of times per year for some backups (got 3x 6tb in it, no raid so I can take them out when needed, also back up stuff to external drives), it still starts-up from the initial sd card as I never finished setting it up. I also have a 1 bay separate NAS for downloading movies that if fails, I will just replace; and a drive attached directly to my router for easy file swaps; so don’t need much running 24x7. While I work in IT (on the Windows side, so the Armbian stuff is still a le…

Hello community, I am running Armbian taken from here on Radxa Rock 4c+. Everything I need seems to be in order (including wifi) but there appears to be no bluetooth device present (it is there using Radxa's images which have old kernels though). I tried to find out what could be the reason and noticed that dtb coming with Radxa has this: wireless-bluetooth { uart0-gpios { rockchip,pins = <0x02 0x13 0x00 0xd0>; phandle = <0xf1>; }; }; in pincntrl section and few other bluetooth/uart related bits while one coming with Armbian does not. I am not sure if this is the root cause and what the easiest way …

Hi all. In download section i do see "large heatsink required" for Rock64. Can anyone post any links to eamples of good heatsink with proper size ? I will be migrating "home server" from Cubieboard2 to Rock64 and chasing long-term stable operation. When board just booted and "does nothing", cpu remains pretty cool. However i'd better be prepared. thanks in advance for tips.

Hi. I was testing pwm with a motor, then my rock pis stopped. After boot, I couldn't see wlan0 in nmtui-connect. So I reinstall fresh armbian, I can see wlan0 again. I do wifi setting with nmtui-connect but after rebooting I can't connect wifi. I have to redo wifi setting with nmtui-connect, put password again and it adds another wifi. It seems like it can't connect to previous wifi. When I do "nmcli con show", I can see the previous wifi but it is deactive. I searched about it and found wifi mac address randomization issue. So I checked "10-override-random-mac-disable.conf". [connection] wifi.mac-address-rando…

Hi everyone, I have been playing a lot (too much maybe) with my NanoPi M4. It seems that most of what I need will be working "soon" (yay for hardware decoding), except HDMI audio bitstream passthrough. Whatever kernel I try, I always get this output from Kodi: Device 1 m_deviceName : default m_displayName : Default (hdmi-sound ff8a0000.i2s-i2s-hifi i2s-hifi-0) () m_displayNameExtra: m_deviceType : AE_DEVTYPE_PCM m_channels : FL, FR, LFE, UNKNOWN1, FC, BC, BL, BR, BLOC, BROC, FLOC, FROC m_sampleRates : 32000,44100,48000,88200,96000,176400,192000 m_d…

Hello, I bought myself a NanoPi M4V2 and 4x SATA HAT for NanoPi M4, hoping to make a small home made server with some docker containers. I installed Armbian buster 5.10.21, downloaded from your site and managed to boot the OS from an attached SATA drive. I have some experience with linux (mostly Ubuntu/Debian), I own and I’ve played with Raspberry boards and I wrote small python scripts to work with GPIO on raspberry pi (how to blink a led or how to connect and display some text on an I2C 16x2 LCD). I thought that might be a nice project if I could connect an I2C LCD to nanopi and display some text text from python script, but here where I hit a bric…

Hello all, I am trying to interface with the MCP2515 on SPI2 of the RockPi4B on Armbian 22.08.6 Bullseye with Linux 5.15.74-rockchip64 and encountering some issues. The rockpi4B pins that I am using to connect to the MCP2515 INT - GPIO2_A7 MOSI - GPIO2_B2 MISO - GPIO2_B1 CLK - GPIO2_B3 CS - GPIO2_B4 When using the overlay file that I have shown below, the output for "dmesg | grep mcp": [ 6.662536] rockchip-pinctrl pinctrl: unable to find group for node mcp2515_int_pin I have been able to get the MCP2515 to initialize successfully, but only if I comment out the pinctrl-0 reference to the mc…

Hi, is is possible to port the kahdas-edge2 changes (https://github.com/armbian/build/pull/6335) to the OrangePi 5b device tree?

By pure accident, I discovered that Ctrl-Alt-F1 while the P2 is booting brings up more options on mine that allows the deletion of firmware and clearing of emmc. I have not done it but the menus are there.

After a ton of time porting the dts for modern kernels, i have a working release for the Bobcat 300 29X Variant To compile https://github.com/sicXnull/armbian-build/tree/Bobcat-29x . ./compile.sh build BOARD=bobcat-29x BRANCH=current BUILD_DESKTOP=no BUILD_MINIMAL=yes EXPERT=yes KERNEL_BTF=no KERNEL_CONFIGURE=NO KERNEL_GIT=shallow RELEASE=bookworm Link to Prebuilt Armbian-unofficial_26.02.0-trunk_Bobcat-29x_bookworm_current_6.18.4.img.xz First check to see if you have a compatible version. Flip the unit over and check the serial number. It will start with G290 or 295. This does not work on 28 or 285. How to Flash 1) In…

Hi, just got a Nanopi R5C (waiting for an RPi for more than a year, yet...) but I couldn't find any headless images for this little box. There's an official debian-image available running LDXE, but open media vault isn't able to run on an Desktop linux... Any chances there will be support for the Nano Pi R5C / Rockchip RK3568B2? btw: can't choose R5C or just 'others' from the drop-down when creating a new post...

I planned to upgrade and skip current 5.18 (EOL) with edge 5.19 or just use LTS 5.15. Offcial images 5.19/edge (e.g. Armbian_22.08.1_Nanopct4_sid_edge_5.19.5.img.xz) won't boot at all, maybe a short uboot screen. Using uboot v22.04 like other rk3399 boards did not fix it. SInce the nanopct4.conf is boardfamily=media but also works with rockchip64 (which was changed some time ago), building with boardfamily=rockchip64 current 5.15 or edge 5.19 works fine, the cli builds boot as expected. Maybe a general question, which bordfamily fits now best to nanopct4. I remember exactly problems which were fixed bei 150balbes maintainer when pul…

Having successfuly built and installed an Armbian image I would like to configure the WiFi connection as part of the process. Currently on first boot I have to connect a network cable to the SBC and run armbian-config to configure the WiFi manually which is a bit of a drag when I'm updating 5 boards. Is this doable ?

My armbian-config went missing. I know it was there before, but apparently somehow I deleted it. "find / -mount -type f -name armbian-config" gets no hits. Is there a package I can refresh to get it back? Thanks.

Hi, Just got my Helios64 crashed: red error led is blinking. I had a raspberry pi left logging on the USB-C and caught the crash: [567513.689265] rk_gmac-dwmac fe300000.ethernet eth0: Link is Down [567519.833508] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [567828.048254] rk_gmac-dwmac fe300000.ethernet eth0: Link is Down [567834.198593] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [568870.455100] rk_gmac-dwmac fe300000.ethernet eth0: Link is Down [568876.599602] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [647513.282616] Unable to handle kerne…

Hi all, I'm using the @pask build for the M4 v2 and all seems good except I am not getting any sound from the 3.5 Jack ( can't try the HDMI as I don't have anything to plug in ) any ideas chaps ? Edit - this is the output from mplayer MPlayer 1.3.0 (Debian), built with gcc-8 (C) 2000-2016 MPlayer Team do_connect: could not connect to socket connect: No such file or directory Failed to open LIRC support. You will not be able to use your remote control. Playing 16. Tush.flac. libavformat version 58.20.100 (external) Mismatching header version 58.12.100 Audio only file format detected. Load subtitles in ./ ========================…

Hello, After I first installed my Helios64, I feared the 16Gb eMMC would be quickly filled. So when I used nand-sata-install, I chose to boot from eMMC but to have the root filesystem on a 500Gb sata drive. I have now second thoughts about it, since I realized that the OS take less than 8Gb, AND I'd like to add a 5th disk to my raid Halas nand-sata-install doesn't seem to work on an already moved filsystem. lsblk show this for the eMMC and the root partition peyo@helios64:~$ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 465,8G 0 disk └─sda1 8:1 0 465,8G 0 part / ... mmcb…

NVMe hard disk is not recognized anymore after last firmware/image update. localhost kernel: rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout! localhost kernel: rockchip-pcie: probe of f8000000.pcie failed with error -110

Not sure if this is board-specific, but filing here anyway. After installing armbian from Armbian_23.5.1_Nanopineo3_bookworm_current_6.1.30.img.xz , apt doesn't find the key for the armbian repository. root@nanopi:/tmp# apt update Hit:1 http://deb.debian.org/debian bookworm InRelease Hit:2 http://deb.debian.org/debian bookworm-updates InRelease Hit:3 http://deb.debian.org/debian bookworm-backports InRelease Hit:4 http://security.debian.org bookworm-security InRelease Hit:5 http://fastmirror.pp.ua/armbian bookworm InRelease Err:5 http://fastmirror.pp.ua/armbian bookworm InRelease The following signatures couldn't be verified because the public key is not availa…

Hello everyone. I want to try to connect a custom AMOLED DSI display with orangepi 3b https://www.phoenixdisplay.com/product/color-displays/oled/at043qhd3008/ And there is practically no information. Maybe someone has seen or encountered similar problems? Do I understand correctly that the dts section on brightness adjustment does not need to be written, because AMOLED as such does not have a backlight? Is it possible to run such a display using simple-panel-dsi? Another interesting question is how to organize the power supply for such a display? It needs different voltages from 1.8 to 4.6 V

I'm trying to build a linux from source on a RK3399 nanopi-m4. I did the below steps: ### Download and compile ARM-TF ### $ git clone https://github.com/ARM-software/arm-trusted-firmware.git $ make CROSS_COMPILE=aarch64-linux-gnu- PLAT=rk3399 bl31 ### Download and complie U-Boot ### $ cd .. $ git clone https://gitlab.denx.de/u-boot/u-boot.git $ cd u-boot/ $ git checkout v2019.10 $ make CROSS_COMPILE=arm-linux-gnueabi- nanopi-m4-rk3399_defconfig $ cp ../arm-trusted-firmware/build/rk3399/release/bl31/bl31.elf . $ make ARCH=arm CROSS_COMPILE=aarch64-linux-gnu- $ make ARCH=arm CROSS_COMPILE=aarch64-linux-gnu- u-boot.itb $ ./to…

I installed the armbian image on an SD card and it runs fine. Now I would like to run it from the EMMC for long term reliability. i tried following what Dara Ó hEidhin did in this thread but am not successful For some reason google drive is not letting me download the driver assistant so RKdrivetool doesn't see the orange pi board like the video referenced in the thread so i cant flash it that way. I tried running it from the SD card and editing the armbianEnv.txt in the /boot folder from fdtfile=rockchip/rk3588s-orangepi-5b.dts to fdtfile=rockchip/rk3588s-orangepi-5b.dts and am able to see the EMMC drive. then i try a s…

I am using rk3588-sd-debian-bookworm-core-6.1-arm64-20250123.img.gz It is excellent asides from lacking NPU support. Before I go down the path of learning kernel compilation and scanning poorly documented Rockchip repositories, has anyone got a current version of Armbian that includes NPU support? If not, is there any good guide to using a cross-compile system and integrating third part drivers?. On a slightly different topic I would prefer to not use fuse file systems and run off the NVME drive directly. Are there any resources on this?

❯ sudo iperf3 -s ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from 192.167.0.1, port 23497 [ 5] local 192.167.0.2 port 5201 connected to 192.167.0.1 port 23498 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 163 MBytes 1.37 Gbits/sec [ 5] 1.00-2.00 sec 149 MBytes 1.25 Gbits/sec [ 5] 2.00-3.00 sec 104 MBytes 868 Mbits/sec [ 5] 3.00-4.00 sec 141 MBytes 1.19 Gbits/sec [ 5] 4.00-5.00 sec 174 MBytes 1.46 Gbits/sec [ 5] 5.00-6.00 sec 125 MBytes 1.05 Gbits/sec [ 5] 6.00-7.00 sec 106 MByte…

Sorry to repeat another case of this. Have attempted a few times to move boot from SD card to eMMC before the SD card fails. I did according to the wiki doc with nand-sata-install. Since I have OMV, I excluded the exports, and also afterward copied the salt and pillar. Also, in another attempt, on suggestion from another thread, I updated the boot loader and copied again. I can boot to my SD card, mount the eMMC, and see the root structure. From what I can tell in reading the boot output, it can't find any storage device? 4 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found But I can see it whe…

This is the uart output of the latest image Armbian_21.05.1_Nanopct4_focal_current_5.10.35.img.xz DDR Version 1.24 20191016 In Channel 0: LPDDR3, 800MHz CS = 0 MR0=0x58 MR1=0x58 MR2=0x58 MR3=0x58 MR4=0x2 MR5=0x1 MR6=0x5 MR7=0x0 MR8=0x1F MR9=0x1F MR10=0x1F MR11=0x1F MR12=0x1F MR13=0x1F MR14=0x1F MR15=0x1F MR16=0x1F CS = 1 MR0=0x58 MR1=0x58 MR2=0x58 MR3=0x58 MR4=0x3 MR5=0x1 MR6=0x5 MR7=0x0 MR8=0x1F MR9=0x1F MR10=0x1F MR11=0x1F MR12=0x1F MR13=0x1F MR14=0x1F MR15=0x1F MR16=0x1F Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=32 Size=2048MB Channel 1: LPDDR3, 800MHz CS = 0 MR0=0x58 MR1=0x58 MR2=0x58 MR3=0x58 MR4=0x2 MR5=0x1 MR6=0x5 MR7=0x0 MR8=0x1F MR9=0x1F …

Orangepi 5B 1. The armbian with sd card can not detect orangepi 5b emmc disk 2. with orangei5b official image and boot , write the armbian image to emmc , can not boot into UI desktop and drop into inicramfs shell.

Hi, i've an Hdd of 1TB and i would like to use it as a storage for my orange pi 5. I would like to install armbian and boot directly from the Hdd the operating system. I need only to buy the adaptor for sata interface. Before to buy it i've read some posts and also watched this video https://www.youtube.com/watch?v=Z5-sZt_O51w&pp=ygUZb3JhbmdlIHBpIDUgYm9vdCBmcm9tIHVzYg%3D%3D and this guy was not able to boot the orange pi directly from the Hdd because the adaptor was creating some problem. 1) I would like to ask you if someone knows if in this months this problem was been resolved or not 2) If it is not yet solved, i would like to install the OS and…

Thought I'd download the latest image in the hope that it might be more stable ... kernel panic on reboot, booted second time and then whlst trying to update kernel panic again. This board seems to be so unstable it's bascially unuseable

Hello, I'm trying to activate the uart interface Gpio 8 + 10 on the rock pi4. I have currently installed the image of radxa. --> ARMBIAN 5.67 user-built Debian GNU/Linux 9 (stretch) 4.4.154-rk3399rockpi4b My Linux knowledge is still in the beginning. Who can help me to activate the upart interface Gpio 8 + 10 on the rock pi4. Thank you

Hello everyone! Saw that some luckfox boards were getting supported and I was like: YES!!! Flashed an sd-card with the community image. Latest I could find is 25.11.0-trunk.413. And plonked in my working Luckfox Lyra Zero W and it failed to boot. From what I gather there seems to be a missing partition called "misc" and I think it is expected about after the current unallocated 16MB(16,777,216 bytes). I tried creating a 4MB partition after the current unallocated space but it complained about something called "Magic" and my limited u-boot/rockchip/embedded linux experience made me get lost there. This is the serial output: Whe…

Hi guys, I have checked the Buster image and stuck in following issue: On Rockpis, tty2 and (the only working) spi2 sharing the same PINs. Due to this reason, SPI is not functional . from dmesg: [ 1.598230] rockchip-pinctrl pinctrl: pin gpio1-22 already requested by ff0c0000.serial; cannot claim for ff140000.spi [ 1.598269] rockchip-pinctrl pinctrl: pin-54 (ff140000.spi) status -22 [ 1.598287] rockchip-pinctrl pinctrl: could not request pin 54 (gpio1-22) from group spi2-miso on device rockchip-pinctrl [ 1.598304] rockchip-spi ff140000.spi: Error applying setting, reverse things back I try to switch back tty2 to tty0 in dts and also…

I have a problem with Focal on Nanopi-M4V2 is that when it is overloaded and runs out of memory, instead of getting slow it kills the process causing the problem and in the last few cases, logs out out of Ubuntu Mate ;-) [Sun Jul 26 17:12:54 2020] Out of memory: Killed process 12888 (Web Content) total-vm:3097484kB, anon-rss:455520kB, file-rss:1600kB, shmem-rss:16636kB, UID:1000 pgtables:2752kB oom_score_adj:0 [Sun Jul 26 17:12:54 2020] oom_reaper: reaped process 12888 (Web Content), now anon-rss:0kB, file-rss:0kB, shmem-rss:16220kB [Sun Jul 26 17:13:22 2020] panfrost_gem_shrinker_scan: 60 callbacks suppressed [Sun Jul 26 17:13:22 2020] Purging 4595712 …

I have a Rock4 SE Board (or Rock Pi 4 SE) and I'm using the Armbian_23.02.2_Rockpi-4b_bullseye_current_5.15.93 Debian version. (Linux rockpi-4b 5.15.93-rockchip64 #23.02.2 SMP PREEMPT Fri Feb 17 23:48:36 UTC 2023 aarch64 GNU/Linux) I am trying to set up the correct Device Tree Overlay configuration for my intended application. If I use Armbian-config as a tool to demonstrate the issue here. It starts by listing I2C7 and then I2C8. If I go to the Rock4 SE schematic and search for I2C8, it is not even setup as I2C: Then where is I2C6, for example. It's supposed to be there. If I then look fu…

I'm using Armbian 20.11.1 Focal (5.9.11-rockchip64) on my Helios64. When there's heavier load via ethernet (SFTP to a SATA Ultrastar 12TB disk) for something like more than an hour, the entire system will freeze. Not sure if it actually does freeze but I lose all SSH connections and cannot connect anymore via SSH unless I restart the Helios64. Happened today 4 times and it's totally reproducible. Haven't tested another drive yet. What makes this difficult to debug is that under /var/log/syslog or kern.log or faillog nothing relevant is being written as to in what state the device is. Is this a known issue? How can I find out what the problem i…

Does armbian for orange pi 5b provide headless wifi setup like raspberry pi? on raspberry pi, I can modify the sd card. like `touch ssh` and assign wifi login and password in the .conf to achieve headless wifi setup. I don't have a lan cable, monitor and keyborad to set up.

I built a version of Buster with the legacy kernel (4.4). when I try to install the media-buster-legacy-rk3328 package on the system, I get an error - unsatisfied dependencies on the kodi-rk package. I tried installing the Kodi-rk package manually, but it has an unsatisfied dependency on kodi-rk-bin. The kodi-rk-bin package is available and installed, but its version does not correspond to the links with Kodi-rk. Perhaps packages were updated in the repository, but dependencies do not work because of a complex package name (the alphabetical comparison condition is not met) ?

I have been testing the latest Buster Server builds - kernels 4.4 and 5.3 versions on my rock64 board In both cases I see a number of syslog entries relating to device ttyFIQ0 not starting. Does anyone else have this issue? Any ideas how to remove stop it from trying to start? thanks

I have serious issues with the serial number being exposed in /proc/cpuinfo. Especially when browsers have access to this information. Afaik, its u-boot who passed this information on to Linux. Any idea how to mask this from Linux? Your help is appreciated