Rockchip

I was wondering if there is a solution to boot from a USB thumb drive and flash the OS to an eMMC. Currently I´m running ARMbian on a Rock64 with an eMMC module installed. Since I´m still trying to figure out how to set up the device I keep reinstalling the OS. So it would be nice to have a way without opening the case, take out the eMMC, hook it up to the PC to flash and reinserting. Thanks in advance.

Hello, When I comment device via USB 3.0 I see it: ender3@ender3:~$ lsusb Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 004 Device 002: ID 1d50:614e OpenMoko, Inc. Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub However with pins GND, DP1, DM1, +5V Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID …

I can't get HDMI output in RK3399 board Nano PC T4, what I have tried https://dl.armbian.com/nanopct4/Noble_current_gnome-kisak https://dl.armbian.com/nanopct4/Bookworm_current_minimal the SSH is working I can only get a black screen on HDMI Kernel 5.x (Armbian 22) works

I'm trying to run the example.cpp that comes with Pine64-CPP but I am throwing segmentation faults. The man-setup() call initialzes the board with the following if statement in the setup() function in gpio.cpp if((uint64_t)gpio_mem % PAGE_SIZE) and the this->gpioMap = statement that uses SUNXI_GPIO_BASE In the example code, I initialize the pin with man->pinMode (PI_GPIO_24, OUTPUT); The pinMode function in gpio.cpp, launches _setPullupdn with gpio=78 and pud = 1. As expected Inside _setPullupdn, the following is set bank= 2 index = 0 offset = 28 The s…

I have a development board, model eaidk-310, with soc rk3228h (which is said to be the same as rk3328). The official website of the board has been closed, so I cannot obtain more related information. However, I found the official firmware and can use rockchip's official tool for burning. The file structure is as follows. 190798 Jun 8 2020 MiniLoaderAll.bin 33554432 Jun 8 2020 boot_linux.img 374 Jun 8 2020 parameter-linux.txt 6815744000 Jun 8 2020 rootfs.img 4194304 Jun 8 2020 trust.img 4194304 Jun 8 2020 uboot.img parameter-linux.txt is: FIRMWARE_VER:8.1 MACHINE_MODEL:RK3328 MACHINE_ID:007 MANUFACTURER:Rockchip MAGIC: 0x5041524B…

About a year ago, I installed the OpenMediaVault image for CM3588-NAS from here: https://www.armbian.com/nanopc-cm3588-nas/ The image is debian-bookworm, which has since become oldstable, while trixie is the new stable. Is it possible to upgrade the distribution and move to trixie packages, even though there are no trixie images for CM3588-NAS? In theory this seems completely feasible as my apt configurations seem completely standard with something like deb http://deb.debian.org/debian bookworm main contrib non-free non-free-firmware and deb [signed-by=/usr/share/keyrings/armbian.gpg] http://apt.armbian.com bookworm main bookworm-utils bookworm-deskt…

Hi, I was trying to load below Armbian images into NanoPi M4 (just M4, neither M4B nor M4V2). They are able to be loaded in the first place, but when I reboot the board by typing "reboot" command in the terminal, I can only see black screen showing on the monitor, no led flashing on the board even, and the board never boots up again. If I unplug the power cable and plug back again, it boots as expected. Is there any way I can reboot the board remotely? Armbian_20.08.1_Nanopim4_buster_current_5.8.6_desktop.img.xz Armbian_20.08.1_Nanopim4_buster_current_5.8.6.img.xz Armbian_20.08.1_Nanopim4_bionic_current_5.8.6.img.xz Armbi…

Hi, Just received my Nanopi R5C. Flashed the Debian 12 (Bookworm) Minimal/IOT images with Armbian Linux v6.12 from here https://www.armbian.com/nanopi-r5c/. Everything works well except that I could not get the WAN port working. Anyone has any idea? BTW, the Nanopi R5C looks different from the image showed on https://www.armbian.com/nanopi-r5c/. Mine has only 2 x 2.5Gb ports instead of the 3 port. The image on the page looks like a NanoPi R5S... Just a side note. Cheers.

HI. I burned the latest official Rockpi4 focal kernel 5.8.x on both rockpi 4 B and C. The problem is only present on the C model. Both USB 2.0 aren't working at all.

@Igor Kernel enabled Bootsplash works great on the recent 20.08 on Orange Pi 4. However there is a delay of around 20 - 30 seconds before this Bootsplash comes up. Is is possible to enable bootsplash on u-boot also on this image? I built a custom image 20.08-trunk with option "Kernel enabled bootsplash' disabled however could not see u-boot bootspalsh on this image. -Rajesh

I see from photos of the FriendlyElec metal case (without display) for the NanoPi M6 that there appear to be two holes for wifi antennas. Does anyone know if the optional wifi card sold by FriendlyElec comes with antennas? If not, are they a standard size which I can buy somewhere else?

Hello, so we use Kobol 64 with OMV since 4 months, and no problem at all. Just yesterday, want to change Ethernet cable, correctly shutdown the Helios64 NAS, and impossible to start it again. Just have the right system light, but left LED no blinking, no information in the USBC terminal. For the "recovery", press the recovery button, and then press the power button, and the LED System don't light up. What can we do, format the system, and reinstall OMV with all parameters... Not really serious, ins't it ? Thank you for any help. Regard.

Hi, I’m using the Helios64 with Armbian 20.11 Buster ( 5.9.10-rockchip64) On every reboot the SMART counter for “Unexpected_Power_Loss (174)” / “POR_Recovery_Count (235)” incresses by one. I’ve seen this unexpected behaviour on Samsung, WD and Crusical SSDs … Rebooting the box with sync && echo 1 > /sys/block/sdX/device/delete && reboot turns the disk friendly off, but shouldn’t this be done in systemd/kernel?

I’ve googled it but can’t decide, the drive works just fine (it’s the 1st of the three disks I have in the box), no performance issues when copying from/to the box. I’m currently on “Armbian 20.11”, barely get the time to play with the setup due to work assignments, plan to update soon. Thanks! (PS. Newbie here) [ 13.298079] ata1: softreset failed (1st FIS failed) [ 18.449169] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 18.467303] ata1.00: ATA-10: ST6000VN0033-2EE110, SC60, max UDMA/133 [ 18.467315] ata1.00: 11721045168 sectors, multi 0: LBA48 NCQ (depth 32), AA [ 18.470029] ata1.00: configured for UDMA/133 …

Hi! Unless mistaken, I believe audio is missing from 3.5mm jack on the RockPi4b. To enable it, I had: - To update the dts by adding definitions close to the RockPro64 (some available starting in mainline 5.6) - Change them to use I2S0 instead of I2S1 - Enable audio-graph-card in kernel config (I also removed some audio modules which issued warnings/errors during boot) - Patch es8316.c to prevent a kernel panic during boot (found in Ayufan's latest mainline kernel for RockPro64) yannick@rockpi-4b:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: rockchiprk3399 [rockchip,rk3399], device 0: ff880000.i2s-ES8316 HiFi ES8…

Hello, download page for odroid M1 states: I have two questions: - Does that mean that the system will be installed on SD or eMMC? or does that meant booting on SD is just for startup to launch system stored on NVMe (or any other storage)? - Is there a plan for booting from M.2 NVMe M-Key PCIe3.0 2-Lane in the future? Thanks Julien

Hi! I'm trying to install NUT because I connected a UPS device. I'd like to get it working so that the server is shutdown safely when there is a power interruption and that I get an e-mail notifying me as soon as there is an interruption. Already after installing via sudo apt install nut nut-client nut-server I get the following warnings: Setting up nut-client (2.7.4-8) ... Job for nut-monitor.service failed because the service did not take the steps required by its unit configuration. See "systemctl status nut-monitor.service" and "journalctl -xe" for details. invoke-rc.d: initscript nut-client, action "restart" failed. ● nut-moni…

Hi, I received my new rock64 today and I downloaded this image https://dl.armbian.com/rock64/Debian_stretch_default_desktop.7z I used Etcher as recommended to create the SD card and booted off of it with just power and network connected as I assumed it would boot, assign a dhcp address and bring up sshd so I could remote onto it. I scanned my network to see if any new devices had been added with dhcp, but couldn't see anything new so I connected the rock64 up to a TV and then booted it up, connected up a keyboard and noticed it ran through an install process on first local login. I followed all the directions and a desktop appeared on s…

I recently plugged in a 4TB Seagate Expansion hard drive and it worked fine. After rebooting the Rockpi4B via 'sudo reboot' the drive is not recognised - dmesg shows: [ 3.877060] sd 1:0:0:0: [sdb] Unit Not Ready [ 3.877082] sd 1:0:0:0: [sdb] Sense Key : 0x4 [current] [ 3.877094] sd 1:0:0:0: [sdb] ASC=0x44 <<vendor>>ASCQ=0x81 Any ideas?

After a recent update to non-kernel stuff, my Helios64 will no longer boot. When attempting to, I get this error: [ 32.425508] xhci-hcd xhci-hcd.3.auto: Host halt failed, -110 [ 35.019496] xhci-hcd xhci-hcd.3.auto: Host halt failed, -110 [ 35.020028] xhci-hcd xhci-hcd.3.auto: Host controller not halted, aborting reset. I had been using the eMMC on board to boot with the SD card as a backup, but now neither one is working. Anyone know if there's a way to fix this? Here's more, using verbosity=4 in the armbianEnv.txt. Spoiler DDR Version 1.24 20191016 In channel 0 CS = 0 MR0=0x18 MR4=0x1 MR5=0x1 MR8=0x10 MR12=0x7…

Object: Enable OTG serial console capability( It was enabled by default I think ) What I was checked/tested: g_serial on /etc/modules ttyGS0 on /etc/securetty serial-getty@ttyGS0.service enabled dwc3-0-host enabled/disabled Windows 10 1809 host g_serial recognized R2S as 0525:A4A7(rev0509) Behavior: OrangePi-Zero: Works well( g_serial recognized as same VID/PID but rev0419 ) <== There are no problems on Windows host driver or configurations[ELMO GMAS(5/4/2014, v2.0.0.1) / usbser.sys(v10.0.17763.1)] NanoPi-R2S: Connection fail. Even manual configure 9600 through 115200 bauds. => Putty alerts few m…

Hello everyone, I have an issue in here. I'm very new to these things so have little knowledge and thus, forgive me if i ask something stupid but i have a problem. I have installed armbian debian verson to my NanoPC T4 and installed i3wm and did a lot of configuration and filled it with junk but i almost achieved what i'm trying to. Yet as i mentioned, i also filled with a lot of junk while trying to achieve my setup for my project. Anyway, from what i know is that what i'm asking is not the linux way but while trying, i found a problem on my case. I wanted to make a clean installation and fill the things i found out worked with the se…

Hi - I'm running on a Rockpi 4c on Armbian 21.02.3 Buster and it the pcie-gen2 overlay doesn't seem to do anything - I have edited the /boot/armbianEnv.txt user_overlays=rockpi-penta overlays=pcie-gen2 It makes no difference if I include the pci-gen2 overlay. lspci -vv LnkCap: Port #0, Speed 8GT/s, Width x2, ASPM not supported, Exit Latency L0s <256ns, L1 <8us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/…

Armbian/Jammy is working like a charm, thanks guys. Settings up the encryption was a bit of bitch but its working as you can see. Any chance of adding encryption to the installer?

Hey, I have uninstalled cron from my system completely, but I just thought I might help contribute, even just a little, by making some services and timer files to replace the ones in these folders: /etc/cron.d /etc/cron.daily /etc/cron.hourly /etc/cron.weekly Now keep in mind that I have not fully tested any of these yet! I would appreciate feedback in testing these, since most of these I won't even use on my system. I barely even use the armbian-config utility at all, so... yeah... The files in question are these. Let me know if I should add more: armbian-truncate-logs armbian-updates armbian-ram-logging The…

I have a serious problem as I mentioned in a title Currently I'm using Armbian on my NanoPi M4 and very satisfied its functionality But when I try to use usb3 device (especially camera from ZWO campany, ZWO ASI 178) with it, it doesn't recognize it as USB3 device but USB2 by checking the data transfer speed with "lsusb -t" Then, once I unplug the cable and plug it to the pi again, that device is recognized as USB3 and the data transfer speed becomes much higher. I need to get USB3's fast data transfer as soon as the board gets booted, without unplugging cables since now it's not that easy to access to the board and cable. I tried usb r…

I have an Orange Pi 4B. The board as the only USB 3.0 port has the USB-C type. I connect the USB-C x USB-A adapter. I connect the USB flash drive and it doesn't work. Power from the port is coming out properly. Is there any chance that this port will work properly with an external drive?

Hello, I have installed the currently provided image "Armbian_24.11.1_Nanopct6_bookworm_current_6.12.0_minimal.img.xz" on my NanoPC-T6 (not LTS). Unfortuantely the only one USB3 port is not working. So no local access is possible and no external USB storage device can be used. I wonder if no one else has such problem reported yet since 3 weeks now (released 2024-11-21). The USB3 port is working with the FriendlyELEC image (rk3588-sd-debian-bookworm-core-6.1-arm64-20241112.img.gz), so maybe there is a small problem with a kernel module or the device tree. If someone can guide me to a starting point for investigation, I can do some debugging. I have little…

Hi, I'm very pleased with my Helios 64, but since I updated to Armbian 20.11.6 (from 20.08.11 or 21, not really sure) it reboots at random times: it can run fine for over two weeks and reboot twice in 36 hours, always when idling. It's running OMV as well a multiple Docker containers: PiHole, Wireguard, Nginx, Transmission, restic-server and n8n. Is it a common issue? What fixes do you recommend? What should I look for to diagnose the issue? Thank you. Edit: forgot to mention that I'm using SnapRAID and mergerFS, as well as NFS shares.

News related to Helios64 : Production Software update Wiki / Documentation update Etc...

I've found a problem with Armbian on the NanoPi Neo 4 with USB 3.0. I have a RAID6 via four USB 3.0 external hard disks (I know, not optimum but it's been working fine for years off an older ARM box using USB 2.0). While the RAID works fine on the USB 2.0 port (established this was true afterward), when connected to the USB 3.0 port, the USB 3.0 hub I'm using disconnects after only a few seconds, disconnecting all the drives (of course). I initially used an unpowered USB 3.0 hub (I forget the manufacturer; I can check). I figured at first, this might be a power issue (even though the external drives are all self-powered). I found a 10-port power…

After the official release of Armbian 20.11 today I would like to collect feedback if and how the firmware runs on the Helios64. Is it possible to upgrade already or should we Helios64 owners wait? apt-get lists these already... armbian-config/buster,buster 20.11 all [upgradable from: 20.08.22] armbian-firmware/buster,buster 20.11 all [upgradable from: 20.08.22] libgssapi-krb5-2/stable,stable 1.17-3+deb10u1 arm64 [upgradable from: 1.17-3] libk5crypto3/stable,stable 1.17-3+deb10u1 arm64 [upgradable from: 1.17-3] libkrb5-3/stable,stable 1.17-3+deb10u1 arm64 [upgradable from: 1.17-3] libkrb5support0/stable,stable 1.17-3+deb10u1 arm64 [upgradable f…

I have installed Armbian 21.02 Ubuntu 20.04 Focal with Linux kernel 5.10.16 and OpenZFS 2.0.1-1 on my Helios64. Created a three-disk encrypted RAIDZ pool with the following command: sudo zpool create -f -o ashift=12 -O compression=lz4 -O atime=off -O acltype=posixacl -O xattr=sa -O encryption=aes-256-gcm -O keylocation=prompt -O keyformat=passphrase tank raidz1 /dev/disk/by-id/foobar1 /dev/disk/by-id/foobar2 /dev/disk/by-id/foobar3 Then I did a single sequential read benchmark with fio on /tank: cd /tank sudo fio --name=single-sequential-read --ioengine=posixaio --rw=read --bs=1m --size=16g --numjobs=1 --iodepth=1 --runtime=60 --time_based …

The wireless interfaces are not coming up [ 16.959456] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 16.969238] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 16.971635] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 16.971650] cfg80211: failed to load regulatory.db [ 41.751941] rk_gmac-dwmac ff540000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 41.751976] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

For anyone looking to build an iSCSI target on their new Helios64, I can confirm that it's working correctly under the test builds for Armbian 20.11. Thanks to @aprayoga for his comment on the pull request, the kernels modules related to LinuxIO have been added to all boards in the Armbian project.

Hello Everyone, Unfortunately my helios64 is not glowing any power LED. As soon as I connect the power supply it only shows a blinking orange LED light, that is basically for the battery status. My power supply is perfectly fine and even I have tried using with the ATX power supply same result. Does anyone face this issue and please help me to get my board working again. Thanks!

My NanoPi M4V2 wont boot. It has a solid red light no green at all. I cant access it with SSH. I went through the troubleshooting checklist available for the NanoPi in regards to the red light. Nothing was solved. I tried different SD cards with different types of images and different types of burners. Nothing works. I know that the SD cards, images, and burners are not the problem cuz I tested it on a Raspberry Pi with no problems.

Hello, Recently the HDD Cable Harness for my Helios64 malfunctioned. SATA Ports 1 and 2 are both no longer getting power/HDDs are not spinning up. I confirmed that it was power by plugging the SATA cable into ports 3, 4, and 5 on the motherboard which all function. I also iterated through the system by removing all the HDD's and testing each HDD slot one at a time. All 5 HDDs fucntion individually in a USB drive enclosure, and all 5 function in my server system and I can mount the RAID array. My question is, does anyone know how to contact the Helios/Kobol team so I can purchase a replacement HDD Harness Cable? …

Hi everybody, I am currently facing some struggles with the nanoPC-T4 recently bought to run armbian. When I got the board, I was able to run android default installed OS, but also armbian from a SD card. But along the way, I decided to install armbian on an NVMe SSD memory to prevent running the OS from the SD card, anyway ... That when I started playing to with the kernel build, u-boot, flashing the emmc etc .. I tried couple of times using the rockchip tool : developtool in MASKROM to play with the EMMC because I couldn't boot from the SD card, and wanted to start with a clean emmc, but every time the tool had to execute a libusb_bulk_transfer, …

We have been stuck on version 6.1 for almost half a year ever since the initial attempt to migrate to 6.12 caused some issues with HDMI if I remember correctly. Anyone knows if 6.12 or 6.14 are still in the works for this SBC? Thank you!

Hi. I am kind of linux newbie. I want to use serial console with my Rock Pi S thru usb otg. I googled and found this from https://gist.github.com/lukicdarkoo/a87f79b1c25cd86bdc47a8784d6eee9c. I tried it but failed. And I found that there was not "sunxi_usb_duc" directory. Any advice would be apreciated. =============================== ok, I just found that these are for orange pi. Any guide for rock pi s? =============================== After install new image, now I can use serial console with usb otg.

Hi - trust this is the right forum. I have forgotten the login password to my Arbian installation on the nanopi m4 V2. It boots from the eMMC just fine, but I am stuck at the prompt. I had only just installed it a few weeks ago (then things got hectic), so nothing really invested - I could just install again via the SD card, right? Unfortunately, it looks like the SD slot is no longer working. In the last 2-3 days nothing seems to boot from it. Which leaves me with an eMMC module loaded up with an Armbian - I think its bionic, because it does have wifi (buster never worked with wifi). In other 'vanilla' flavours of of l…

Is there an issues page relating to the M4V2 and Armbian Focal. I'm testing it and I have a few strange things happening with NFS and network but I was wondering if there as a known issues or a general topic regarding this board and this Ambian build because searching for nanopi-M4V2 Focal... is not a good idea. Thanks

Hello, I recently bought a Rock 3A and trying to use Armbian, I am very newbie in this area. I tried few options available (22.08.2 Jammy & Sid) for Rock 3A from here but in all of them the boot fails and falls into endless initramfs Can you give me a hint what could be cause of this?

I am downloading three different builds from 6.12 for orange pi 5. I have an orange pi 5 pro but since there is not dtb entry in 6.12 for that sbc in the Armbian 25.8.1 6.12.28 dtb file I used the orange pi 5b.dtb entry which works with the Armbian 25.8.1 6.1.115 images. The result is that the initramfs cant find a root disk - and when checking for drives in initramfs - there are none ls /dev/disks/by-uuid. So the initramfs file isn't running correctly as its not finding drives. I went back and loaded Armbian_24.8.1_Rock-5c-trixid_current_6.12.42_minimal.image and that boots up to root login. However if I change the card type to orangepi-5b. I cann…

Hi, I want to use the I2S GPIO output pins on Nanopi m4 to connect to multi channel DAC. Unfortunately I can not see it as a playback device: user@nanopim4:/home$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: realtekrt5651co [realtek,rt5651-codec], device 0: ff890000.i2s-rt5651-aif1 rt5651-aif1-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: rockchiphdmi [rockchip,hdmi], device 0: ff8a0000.i2s-i2s-hifi i2s-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Is there a way to enable I2S output on GPIO? 36 | I2S0_SDO0(1.8V) 37 | I2S0_SDI1SDO3(1.8V) 38 | I2S0_SDI2SDO2(1.8V) 39 | …

Hello, I think this is my first post here. I am trying to operate an Epson L4150 on-board Rock pi4 b multifunction printer. I was successful in running the printer. But the scanner is another story. Xsane does not recognize it. I have been trying to install the driver which is downloaded from the Epson page, but it is for armhf. I tried a dpkg --add-architecture armhf, then update, but when I try to run install.sh from the Epson driver, it throws error: E: Failed to locate package libboost-filesystem1.58.0 Somebody could help me? Thank you

The mainline 5.11 patch "phy: rockchip: set pulldown for strobe line in dts" https://github.com/torvalds/linux/commit/8b5c2b45b8f0a11c9072da0f7baf9ee986d3151e (not backported to 5.10.y) seems to have broken most if not all rockchip board EMMC HS400 enhanced strobe support. This probably affects supported rockchip boards (at least rk3399 ones, but probably most). That is boards exhibit: [ 18.985162] mmc1: running CQE recovery [ 18.988056] ------------[ cut here ]------------ [ 18.988500] mmc1: cqhci: spurious TCN for tag 12 and the filesystem ends up corrupted on write attempt. Note that another bug about regulator core DEFER…

hello, i was trying to set up a 2 pin fan on my orangepi 5b and i connected it to pin 25 and 26 (GND and PWM1). When i first started this task, the output from gpio readall would show me all 26 pins on the board. As i was digging through some forums to try and get the PWM pin to operate as on/off, i came across wiringOP and when i installed it, the output of `gpio readall` changed to only show 8pins. I am unsure of what went wrong and why it only shows 8 pins. I tried removing wiringOP and it still has not made a difference. Thanks

Hi all, I have a Friendlyarm nanopi M4 running armbian, I have tried to install dotnet core without success - anyone here managed it ? I followed a tutorial but when I get to the apt-get install part I see this error Couldn't find any package by glob 'dotnet-sdk-2.2'

Hi I have spent couple of days to enable the SPI3 (the only SPI that has been routed to the 40-pin header) on Rock3A, but no success. I am trying to enable SPI3M1C0 with following pins on my Rock 3A GPIO4_C2 (CLK), GPIO4_C3 (MOSI), GPIO4_C5 (MISO), and GPIO4_C6 (CS0). I am out of idea, try different overlays but still not able to enable them. I used this overlay from this repo https://github.com/radxa/overlays/blob/main/arch/arm64/boot/dts/rockchip/overlays/rk3568-spi3-m1-cs0-spidev.dts I expect to see “/dev/spidev3.0” but nothing appeared. I have already added 2 overlays, 1 for 1-wire, and the other for I2C, and they are worki…

Hi, I tried the new Bullseye image from https://www.armbian.com/station-m1/ to check bluetooth support but nothing is displayed on the screen at boot. No video signal come from the Station M1. The TF card used works with other images. Any hints ? Chris

I've been trying to connect a USB hdd for a while now, and depending on the SATA disk and the USB<->Sata adapter I've had different behaviours : * 700mA hdd * Adapter A works, can mount and copy * Adapter B is detected, the SATA device too in dmesg, but does not appear in lsblk. * 1A hdd (Seagate Barracuda 2To 2.5'') * Adapter A seems to be detected, the disk tries to start (sde is showing in dmesg) but usb device disappears, reappears etc ("usb disk bootloop") * Adapter B is not even detected in dmesg or lsusb ! Obviously, the 4 configurations perfectly work on a x86 host. What could be going on ? I'm pr…

I have a strange problem with my R2S. I grabbed latest buster and focal images, burned them using Balena Etcher onto a pair of 32GB SanDisk Extreme Cards and neither is booting. Serial console shows that boot process gives up waiting for root file system and drops me into initramfs shell. Looking into /dev, I see no mmcblk0 device (or any other block device apart from loops). If I now eject and re-insert the card, the device shows up. If I do it during boot process, while the board is still waiting for rootfs, boot process continues correctly. Reboots are fine, but if I unplug the board for longer than a second it's back to initramfs for me. …

Hello, I have an ARMBIAN image 08.21.6 kernel 5.10.16 it works very well on rockpi 4B + rev 1.6 I tested the last Kernel but without more success. when we fix the ip address and we up (several times) the eth0 network this one puts to work at a time. Do you have an idea ? Regards.

Hi all. Some time ago, in the release notes of a past Armbian version, I remember reading that the network LED should now be enabled by default and associated with eth0. Despite always keeping my Helios64 as up-to-date as possible, mine never lit up, but I didn't think much of it. Today I decided to investigate why, and I'm not sure where to go from here. First things first, the LED works, it's not a hardware issue. I can echo 1 and 0 to the LED path (/sys/class/leds/helios64:blue:net/brightness) and it lights on and off as expected. From what I can tell, this LED, along with the heartbeat one, is enabled by the Systemd unit helios64-hear…

Hi I just installed armbian on my rockpi 4c+ and wanted to check the temperature so I found that I should be able to run cat /etc/armbianmonitor/datasources/soctemp But that just gives the error cat: /etc/armbianmonitor/datasources/soctemp: No such file or directory It seems /etc/armbianmonitor/datasources/soctemp is a link to /sys/devices/virtual/thermal/thermal_zone0/temp but I have no /sys/devices/virtual/thermal/thermal_zone0 directory, under thermal I have ├── cooling_device0 │ ├── cur_state │ ├── max_state │ ├── power │ │ ├── autosuspend_delay_ms │ │ ├── control │ │ ├── runtime_active_time │ │ ├── runtime_status │ │ └── runt…

Hi there, I'm trying to made a dts file to handle a pican2 hat on ROCK64 armbian, but now I'm stuck. I'm a noob in writing dts files, I've tried to take as exemple dts from RPI and Thinker. edit: I've rebuild the kernel, and build the mcp251x.ko module, it load like a charm. But I assume I've to write a correct .dts file to link it to my devices tree. here is my loaded modules list: Module Size Used by can_bcm 24576 0 can_raw 20480 0 can 53248 2 can_bcm,can_raw mali 262144 0 rt2800usb 28672 0 rt2800lib 81920 1 rt2800usb rt2x00usb …

[🌱] artifact [ armbian-desktop :: armbian-desktop() ] [💖] artifact [ present in local cache: armbian-bullseye-desktop-gnome 23.05.0-trunk--1-V5999-B8177 ] [🌱] artifact [ armbian-bsp-desktop :: armbian-bsp-desktop() ] [🌱] Getting ORAS manifest [ ORAS manifest from ghcr.io/armbian/cache-packages/armbian-bsp-desktop-orangepi5-legacy:23.05.0-trunk--1-B0996 ] Error: GET "https://ghcr.io/v2/armbian/cache-packages/armbian-bsp-desktop-orangepi5-legacy/manifests/23.05.0-trunk--1-B0996": GET "https://ghcr.io/token?scope=repository%3Aarmbian%2Fcache-packages%2Farmbian-bsp-desktop-orangepi5-legacy%3Apull&service=ghcr.io": response status code 403: denied: requested access…

Hi Folks, I have a NanoPiM4 and loaded Ambian 5.75 onto an SD card, it boots great (Thanks Armbian!). How I've added the FriendlyElec 2.8 TFT module (240x320) and want to configure it. So I used the handy `armbian-config` to pick up the kernel headers and sources, and went to go an add fbtft and select the ST7789V driver. Only when I went to run `make menuconfig` I got: root@nanopim4:/usr/src/linux-source-4.4.174-rk3399# make menuconfig scripts/kconfig/mconf Kconfig net/Kconfig:83: can't open file "net/wireguard/Kconfig" scripts/kconfig/Makefile:28: recipe for target 'menuconfig' failed I've updated the armbian monitor stuf…

I notice the Helio64 hardware supports WOL, but I can't see anything in the Wiki about it (only Helios4) The Helio64 can draw some power with 5 spinning disks, I would love to have it sleep until needed. Is there any information on setting this up? I can see Autoshutdown plugin for OMV, but there is options for: Shutdown Hibernate Suspend Hybrid Sleep Suspend then Hibernate Does Helios64 support all these methods? Then once the unit is in some form of shutdown or sleep state, how can I make use to WOL to wake it up? Thanks.

I've recently used armbian-install to enable booting from my nvme/ssd drive and all appears to be working fine. However, I'm curious to know, why, the device is mounted twice as shown below. The / mount point is in /etc/fstab but where/how does the device get mounted again on /var/log.hdd. mount|grep nvme /dev/nvme0n1p1 on / type ext4 (rw,noatime,errors=remount-ro,commit=120) /dev/nvme0n1p1 on /var/log.hdd type ext4 (rw,noatime,errors=remount-ro,commit=120)

This is a HTML5 audio/video tester for web browsers: https://tools.woolyss.com/html5-audio-video-tester/ As you can see .webm is not enabled because frankly I have no idea which package I need to enable that. I have opus and av1 installed: ii libdav1d5:arm64 0.9.2-1 arm64 fast and small AV1 video stream decoder (shared library) ii libopus0:arm64 1.3.1-0.1build2 arm64 Opus codec runtime library I tried gstreamer1.0-ugly and gstreamer1.0-bad but to no avail. Any idea's which package I am missing?

My Helios64 NAS is suddenly randomly just, stopping. It appears to be totally random. It doesn't appear to be some form of actual shutdown as the front panel lights all stay on. I lose all access including the serial console. The only way to reboot is a long press on the power button to actually physically reboot the box. I've cranked the verbosity up to 7 in /boot/armbianEnv.txt in case something is output on the serial console but I've not seen any useful output yet but for obvious reasons it's hard to catch it happening. Because /var/log is cleared every boot I can't see if anything was logged just prior to the halt event. Not sure where to…

Hello to everyone Trying to use armbian on RockPi 4C plus. Got kernel OOPS. Kernel crushes in different moments: mostly during systemd units starting or just after boot finished. Backtraces are different (no common). Faulty images: 1) From the https://www.armbian.com/rockpi4/ For Model C+ here: https://redirect.armbian.com/rockpi-4cplus https://mirrors.dotsrc.org/armbian-dl/rockpi-4cplus/archive/ Armbian_22.11.1_Rockpi-4cplus_bullseye_current_5.15.80_minimal.img 2) Built by myself Armbian_22.11.2_Rockpi-4cplus_bullseye_current_5.15.84_minimal.img Armbian_23.02.0-trunk_Rockpi-4cplus_bullseye_edge_6.1.8_minimal.img Armbi…

I've got a Rock64 1GB (rk3328) running Focal with the legacy 4.4 kernel. I've compiled and installed from source various things like libmali, libdrm, mpp, ffmpeg, and gstreamer, and have successfully gotten ffmpeg and gstreamer to do hardware decoding and gstreamer doing hardware video encoding. I also managed to compile and install xserver 1.20 from the rockchip-linux Github and have it running a barebones LXDE installation. I am now setting my sights on Kodi. I have stock LibreELEC installed and working on another sdcard, but my TV only supports 50Hz, 59.96Hz, and 60Hz refresh rates, meaning that 23.976fps content does not play smoothly. I've read enough to …

I have a nanopi neo3 rk3328. I would like to modify the i2s(1) at start. I tried to modify /boot/dtb/rockchip/rk3328-nanopi-neo3-rev02.dtb but nothing change. Which is the right dtb file its load at start? Thank you.

Hi, I am doing some overlay for fbtft LCD driver - SSD1322. I did compile an add my patch, now I would like to load the LCD driver with DT overlay. This is what I have done: /dts-v1/; /plugin/; / { compatible = "rockchip,rk3399"; fragment@0 { target = <&spi1>; __overlay__ { status = "okay"; }; }; fragment@1 { target = <&spi1>; __overlay__ { /* needed to avoid dtc warning */ #address-cells = <1>; #size-cells = <0>; status = "okay"; mytft@0{ compatible = "solomon,ssd1322"; …

Hello, Has any one installed and used OV5647 Sensor camera on orange pi 3b ? I can see the camera is listed. but there is no driver. Below is output. Can some one help ? -la /dev/video* -rw-rw---- 1 root video 67 Aug 8 13:53 /dev/video-dec0 -rw-rw---- 1 root video 4 Aug 8 13:53 /dev/video-enc0 sudo modprobe sun6i-csi [sudo] password for XXXXX: modprobe: FATAL: Module sun6i-csi not found in directory /lib/modules/6.1.115-vendor-rk35xx dmesg | grep -i mipi [ 12.108168] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: enter mipi csi2 hw probe! [ 12.108575] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: probe success…

Hi folks, I have a Firefly AIO-3399C which boots Armbian fine, but no USB devices besides the root devices are detected. This happens with both the kernel 5.19.170 and 6.0.7 based images, made by @balbes150, which I've downloaded from https://users.armbian.com/balbes150/firefly-rk3399/ Any advice would be appreciated. U-Boot 2022.04-armbian (Nov 03 2022 - 17:26:20 +0300) Linux firefly-rk3399 5.19.17-media #trunk SMP PREEMPT Thu Nov 3 17:40:36 MSK 2022 aarch64 aarch64 aarch64 GNU/Linux In dmesg output, I see the following, which may be relevant: [ 4.616394] hub 7-0:1.0: USB hub found [ 14.296598] fusb30x: module is from the sta…

Can't enable (using armbian-config) GUI ("desktop") without enabling 'auto-login". If I try to do so, GUI simply doesn't start. OrangePi 4 (not B), Armbian Buster. Which log shoud I look for info / include on forum?

Hello all, I am running Armbian 23.05.1 rock5b jammy legacy on a rock5b. The current kernel version, as given by uname -r, is 5.10.160-rockchip-rk3588. I'm attempting to build a driver module but have been unsuccessful because I'm unable to locate the kernel headers. I have tried installing the headers with apt install linux-headers-$(uname -r) but result in a package not found error. I also tried searching for the headers in my file system with find / -name "linux-headers-$(uname -r)" but the command returned no results. I suspect that the kernel headers may not be installed, may be installed in a non-standard location, or …

I have tried the Debian image for ROCK5B and the Gnome GUI works fine there. But when booting the Armbian image (running from emmc) the screen does not notice any signal from the ROCK5B regardless of which HDMI port I try. I am using a quite old HDMI monitor (connected though a DVI-HDMI adapter). How do I debug this?

So now I am playing with Rock64 4GB. I installed the Armbian_5.65 server edition OS and then installed xorg, lxde, and lxdm., then rebooted into a working system. Final stage of setting up was to test rhythmbox_3.4.2 and there was no sound. pavucontrol > playback shows the app is running and the worm is leaping about, but absolutely no sound. Same playing a .wav file with mpv, or indeed any player. Is there something unusual about the audio socket, or some other limitation. armbianmonitor -u = http://ix.io/ltt0

Hello! I'm able to reproducibly get a kernel oops whenever I start a docker container on my Helios64 The SD card I was running my Helios64 from died and so I reinstalled Armbian using the steps to install bookworm from this post. I did skip the steps related to hs400 and L2 cache as I'm currently running the system from an SD card. After the install seemed to be working well I installed zfs, imported my existing pool, and then installed docker. My previous setup was using docker's ZFS storage driver so I got that configured as well. Now, whenever I start up a docker container (ie by running "sudo docker run hello-world") I get the foll…

I have an orange pi 5b running Armbian_24.2.1_Orangepi5_bookworm_legacy_5.10.160_cinnamon_desktop on EMMC just fine. i wanted to try a newer version with hardware acceleration so i tried Armbian_24.11.2_Orangepi5_bookworm_current_6.12.0_cinnamon-backported-mesa_desktop. I edited the file in the boot folder and could see the EMMC on reboot. i did a sudo apt update and sudo apt upgrade. then an armbian-install to install it to the EMMC. it would not boot from the EMMC but i could at least still see it. Then i tried Armbian_24.11.2_Orangepi5_bookworm_vendor_6.1.75_cinnamon-backported-mesa_desktop and did the same but now i cant see the EMMC even with the ori…

Hi FireFly station P2 on Armbian 22.11 Bullseye XFCE does not work on a 4K monitor. When turned on, ripples appear on the screen. Examples of images from links. The same problem at station M2. station m2 and station p2 do not work on a 4k monitor both

Hi all, I have been using a Rock64 with hostapd and a usb adapter that uses realtek drivers for a couple of months now. Recently, like a week or two, after what i believe was a kernel update i started getting random freezes in the board. As i use it "headless", when it happens the only way to get it back working is by power cycling it. This means that until today i had no logs of what was happening. Today although, i left my laptop on for a couple hours, with tail -f on kernel.log, messages and syslog. Attached in the file called logs.txt is what i managed to obtain from a terminated ssh session to the board. Im running Linux NetMa…

Hello everyone, Do you think the emulation of ps2, gamecube, saturn etc video games works better on armbian or on android with a device on a rk3588 chip? thanks

Had anyone tested DAS mode performance with Capture One? Or could someone explain to me how it works? Also, would C1 show the DAS mode and NAS mode as seperate volumes or is it smart enough to show up as the same one? Background: Capture One doesn't work well with network drives. Editing images, moving raw files, even saving catalog backups is dramatically slower on a NAS than a DAS or internal drive. It doesn't matter how fast the drive or network is. Its a long standing bug they're always quick to say they aren't prioritizing fixing. I've looked at other NAS's that do a DAS mode by running a 10GBE connection over thunderbolt and that's a great solution in ev…

RK3576 nanopi M5 cannot start Waydrod I am trying to use Waydrod on the nanopi M5, and I am starting it up CONFIG_ANDROID_BINDER_IPC=y CONFIG_ANDROID_BINDERFS=y CONFIG_ANDROID_BINDER_DEVICES="binder,hwbinder,vndbinder" However, during the actual startup of Waydrod, there was a continuous black screen crash and restart. The following is the error log: nano@nanopi-m5:$ waydroid show-full-ui [13:55:56] Introspect error on :1.103:/ContainerManager: dbus.exceptions.DBusException: org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, th…

While I like having the helios-ups.timer in case of power failure, I don't like that my logs get three lines written to them every 20 seconds. Apr 09 07:43:26 helios64 systemd[1]: Starting Helios64 UPS Action... Apr 09 07:43:26 helios64 systemd[1]: helios64-ups.service: Succeeded. Apr 09 07:43:26 helios64 systemd[1]: Finished Helios64 UPS Action. Does anyone know if there is a way to keep the timer on but not fill the logs this way? Everything I've found about silencing systemd messages is about the output of the command, not the systemd activity itself.

https://www.armbian.com/odroid-m1/ - kernel 6.1.y LTS

Hi all, I installed the desktop using armbian-config Install Browser and other but It still boots into a shell - what else do I need to do ?

Hello, friends... The current MIPI DSI driver provided by Rockchip Inc. in older U-Boot versions (v2023 and earlier) is not compatible with U-Boot’s uclass subsystems.(a waste of time if you want to develop). I have done extensive research and made modifications to several files to make it work with the latest U-Boot versions. I have tested it with U-Boot 2023.10, 2024.10 and v2025.rc3 on orange pi 4 lts, and it works perfectly. I'm attaching the necessary files for those who need them. This u-boot driver is nearly identical to Rockchip's Linux kernel driver, uses same driver file but there some limitations because of u-boot system, bu…

Hi all, I have a nanopi m4 with following installation - Armbian_22.05.4_Nanopim4v2_jammy_current_5.15.48_xfce_desktop. I am looking for someone who has retroarch installed on armbian and fully working, and what the key steps are. Im asking because: 1) I tried installing by command line, which installs retroarch to a location with no cores. An issue with rk3399 cores is that there are none to download and must be built seperately (Is there a way to update a file so that cores can be downloaded through the application?) 2) In an attempt to build retroarch + cores, i downloaded and built libretro, which took probab…

Hi all, I'm trying to build a NAS using the Penta SATA Hat (https://wiki.radxa.com/Penta_SATA_HAT). I'd like to use ZFS as file system. I got the "supported" Armbian Jammy image from here: https://www.armbian.com/rockpi4/ I installed the kernel headers through armbian-config. However, attempting to install the zfs-dkms package gives me Building for 6.1.30-rockchip64 Module build for kernel 6.1.30-rockchip64 was skipped since the kernel headers for this kernel does not seem to be installed. As you can see, my kernel version is 6.1.30-rockchip64: $ uname -r 6.1.30-rockchip64 However, the installed kernel he…

My Helios64 was running fine with 5 HDDs for a couple of weeks, then I suddenly couldn't access the shares anymore and I noticed only two HDDs were running (the rest having no indicator lights). HDD slot 3, 4 and 5 appears "dead", no power up on boot, no indicator lights. I have checked both +12V and +5V rails and they are present, everything is plugged in. I can move the HDDs from slot 3, 4 and 5 to slot 1 and 2 and they will power up just fine. The hard drives also work in other machines. I'm a bit lost as to what might be wrong, any ideas?

Hi, I have deployed a NanoPi Neo 4 and for the most part, I'm happy with it, but am having a peculiar problem. I am using the manufacturer-supplied serial console cable and USB adapter (via screen /dev/ttyUSBx 115200). Once the machine is properly booted, if I hit enter, I get a serial console as normal. However, I get garbage from u-boot (and presumably from the kernel boot messages). It looks just as if I have a speed mismatch. I have tried many other speeds (1500000, 230400, 57600, 38400, 19200, 9600) and none of these seem to work. What am I doing wrong? Or is the state of the box right now that u-boot sends garbage …

Hello, people. I have an Orange Pi 5 MAX, Is there any image for this board? I'm tying Armbian_25.2.3_Uefi-arm64_bookworm_current_6.12.20_xfce_desktop, but I don't know is it's the proper version. I will appreciate any help or indication. Greetings from Argentina PS The form requires tags, but I only can select the tag "solved", that's wrong, itś not solved. I don´t know how to add tags

Hi all, I've just booted my NanoPi M4 V2 after not using it for a year or so and when I log in via ssh I'm told the / usage is at 100% - I've deleted all logs and the usual suspects but to no avail uname gives Linux M4V203 5.10.63-rockchip64 #21.08.2 SMP PREEMPT Wed Sep 8 10:57:23 UTC 2021 aarch64 aarch64 aarch64 GNU/Linux I'm using a 32gb SD card df -h gives Filesystem Size Used Avail Use% Mounted on udev 1.9G 0 1.9G 0% /dev tmpfs 387M 41M 346M 11% /run /dev/mmcblk1p1 29G 29G 0 100% / tmpfs 1.9G 0 1.9G 0% /dev/shm tmpfs 5.0M 4.0K 5.0M 1% /run/lock tmpfs …

Gentlemen, I have a rock64 board, and I would like to use an external RTC module with DS1307 chip. Unfortunately the armbian kernel does not provide DS1307 driver by default: root@rock64:~# cat /boot/config-4.4.162-rockchip64 | grep DS1307 # CONFIG_RTC_DRV_DS1307 is not set I don't have the programming skills for sending a pull request to enable this module. Could you please enable this module for ROCK64? I believe other ROCK64 owners may also benefit from this driver, as the board does not expose a working RTC, and DS1307 is a very common RTC chip. Thanks in advance.

Has anyone activated the ov13855 camera on Orange Pi 5 (kernel 6.1.x)? If so, can you share your experience?

Hello, I have been using Armbian OS on Rock Pi 4B. Full system is on NVME, not using SD card, and there is no eMMC chip on the board. During usage, I needed to shut it down improperly: by removing power cable, not through sudo shutdown now In the end I have following message during boot: Also, here is contents of dev folder: I was wondering if it is possible to fix this error. If not, I will reinstall with new image. Just spent much time on setting the environment, don't want to redo this all I would appreciate any help.

I'm in the process of upgrading my network and with the Helios64 capable of 2.5 GbE, what are some people's switch recommendations? My needs aren't really too high so I think 5 ports should be enough until the rest of the infrastructure catches up in my home network. My short-list are: * QNAP QSW-1105-5T * TP Link TL-SG105-M2 * TRENDnet TEG-S350 Article from servethehome

To continue discussion from Helios64 Support Currently there is no plan to support to disable the power but it's interesting to know such use case. If we implemented this feature, you would need to go u-boot prompt to enable and disable the power. would this acceptable for you? Under Linux device tree, the power rail declared as regulator node with regulator-always-on property. This prevent kernel (and user) to turn off the regulator. Unless we are able to create device node for the SATA port, to act as consumer of the regulator, we can't remove the regulator-always-on property.

Hi, My NanoPi M4 V2 Won't Boot via SD ... the emmc is not installed on the board The RED light is ON but the GREEN stay OFF I cannot reached to read correctly the data coming from the serial port debug (I tested with many bauderate, also with 1500000, same result ... a lot of weird characters) Tested Versions Won't boot: Armbian_22.08.1_Nanopim4v2_jammy_current_5.15.63.img.xz Armbian_22.08.1_Nanopim4v2_bullseye_current_5.15.63.img.xz Armbian_22.11.0-trunk_Nanopim4v2_sid_edge_6.0.3.img.xz Armbian_22.11.0-trunk_Nanopim4v2_kinetic_edge_6.0.3.img.xz Tested Version Boot properly: Armbian_21.02.1_Na…

Hi, after upgrading linux-u-boot-rock-3a-current, linux-image-current-rockchip64 and linux-dtb-current-rockchip64 to the 24.2.1 versions, the system losses the network producing kernel errors in dmesg: [ 432.408850] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 432.410880] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input). [ 432.410929] rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. [ 432.410954] rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 [ 432.410983] rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. [ 432.411002] rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 [ 432…

Hello, i have trouble with my Helios64 (possibly bricked), so I am interested to by a new one. And if i can fix mine, the second one could allow me to participate to armbian support for it. Anyone have one for sale ? Preferably in Europe. Thank you.

I need to turn off the pwr_led light under the armbian system, thank!