Rockchip

I have Armbian running on my NanoPi M4 Everything is fine but.............. I have massive problems with pulseaudio Im not able to get the sound working So i tried to deinstall pulseaudio and install Alsa After that i dont see anything regarding sound in settings menu or on the taskbar For unknown reasons the wallpaper has resettet Anyone who has a solution ?

I have a Rock Pi4 B (rk3399) and I do not find the solution to use my native screen resolution with the latest kernel: 1600x1200. It was working fine with Armbian Bionic Legacy kernel 4.4. However, despite my tinkering, I do not find how to make it work with the latest kernel (option is not available in the Display Setting, xrandr manipulation did not give any success). Any pointer towards a solution would be greatly appreciated. Below the output of xrandr for the two images I ran. Welcome to Armbian Bionic with Linux 4.4.198-rockchip64 Screen 0: minimum 320 x 200, current 1600 x 1200, maximum 8192 x 8192 HDMI-1 connected pr…

Hi I try ro install and use Armbian on my NanoPi NEO 3. But when I do a first boot, I stuck at Generate Locale step. How can I fix it? Thank you very much. .

How do I use a camera that I have connected through the connector on the board? I tried running armbian-config but did not find anything about a camera.

[🌱] artifact [ armbian-desktop :: armbian-desktop() ] [💖] artifact [ present in local cache: armbian-bullseye-desktop-gnome 23.05.0-trunk--1-V5999-B8177 ] [🌱] artifact [ armbian-bsp-desktop :: armbian-bsp-desktop() ] [🌱] Getting ORAS manifest [ ORAS manifest from ghcr.io/armbian/cache-packages/armbian-bsp-desktop-orangepi5-legacy:23.05.0-trunk--1-B0996 ] Error: GET "https://ghcr.io/v2/armbian/cache-packages/armbian-bsp-desktop-orangepi5-legacy/manifests/23.05.0-trunk--1-B0996": GET "https://ghcr.io/token?scope=repository%3Aarmbian%2Fcache-packages%2Farmbian-bsp-desktop-orangepi5-legacy%3Apull&service=ghcr.io": response status code 403: denied: requested access…

It's quite some time ago that I used my rockpi however today I wanted to restart my project again (some sensors with an A/D Board connected to SPI). First of all I tested the Board on a Raspberry Pi (with Raspbian) there it is working as expected so it is not a hardware issue. I connected my board MOSI = GPIO2_B2 (Pin 29), MISO = GPIO2_B1 (Pin 31), CS = GPIO2_B4 (Pin 33), Clock = GPIO2_B3 (Pin 7). The matter is that it sometimes works and the correct data is received but just once in a while. For me it seems that the CS is not working properly but how to get SPI communication working correctly? In the attached screenshot the value 744 is the correct value, i …

When you do gdisk -l /dev/mmcblk1 or fdisk -l you can se that the partition table that armbian is using is MBR (dos). Is any particular reason for this? When you go to the new and improved firefly rk3399 manual page you can see it is making problem when flashing through USB-C cable and upgrade_tool v. 1.24 and v. 1.34 (GBT friendly) http://wiki.t-firefly.com/en/Firefly-RK3399/flashing-notes.html .

Hello everybody ! I'm a newbie RK3288 and Miqi board. When using this board I'm get a idea "Why bring all firmware on SD card into eMMC", because Miqi board will run faster than using SD Card. But, I haven't found any guide to solve this. So, I hope you can help me. Thank for your reading TonyHCM.

Hi there, I'm using the latest version of armbian to run the linuxptp for the ieee1588v2 clock. When I check the timestamp status, the 1Gbps port which is the RTL8122 is no problem, but the 2.5G ports RTL8125BG are only supporting the software timestamp. However, when I checked the Realtek website, it says that the 8125BG also supports the IEEE1588 clock. I tried to install the driver, but it did not work. As a beginner in Linux, I probably don't have the knowledge to compile drivers, in this case I sincerely hope that armbian could officially support the hw ptp timestamp in 8125 NIC. Thank you very much! nanopi-r6s:~:# ethtool -T end0 Ti…

It seems a package is missing from the Armbian 23.8 Bookworm CLI that results in this error. I encountered an add-apt-repository: traceback error. To fix it just run: sudo apt install python3-launchpadlib

I have a project developed on Rock 4C+ v1.2 board. Now there is only v1.41 board available and Armbian is not booting on it at all, no matter it's compiled locally, or it's downloaded from the official sources. UART debug is producing unreadable sequence. So far, what I’ve tried: - I’ve built Armbian with the latest changes armbian build repo - hasn't helped - I’ve used rk3399-rock-4c-plus.dtb file instead of rk3399-rock-pi-4c-plus.dtb, dunno why there are two, but somewhere on the forum I read that this one without “pi” is the right one - hasn't helped - official Armbian images - not booting - Ubuntu and Debian - both booting fin…

Hello, I wanted to install Linux on my TV box but I'm having problems First I tried to put an Android rom that said it was stock But it doesn't boot and the system doesn't start, it was in loader mode and after I did that it went into maskrom mode and it doesn't come out, everything I try to do gives me the download boot fail I don't know what to do to get out of this mode and install something, all the loader files don't work and the ones that say they work, the links are down

rk3588-pcie_bifurcation_2x2-uboot.patchrk3588-pcie_bifurcation_2x2.patch Attached are two patches I've prepared. One for uBoot (to correctly recognize split pcie3x4 to two independent controllers, pcie3x4 and pcie3x2), and one for DT of NanoPC T6. This basically allows you to use trimmed-down bifurcation adapter. The adapter in question must be trimmed down/cut to fit on the back of the board. Tested with 2x NVME, and 1xNVME and QCNFA765 wireless card. I'll post photos later once I'll disconnect the board again from my setup. BEWARE!!! If you'd plan to use more than one ath11k wireless card, you'd need QRTR patch. Since the SBL …

Hello, I have read some threats with the same issue, armbian images are not booting, there is not HDMI signal when turn on rockpi4. General solution is trying armbian image stored on radxa server https://dl.radxa.com/rockpi/images/third-party/Armbian_5.67_Rockpi4b_Debian_stretch_default_4.4.154_desktop_20181210-gpt.img.gz this armbian version works fine but it's too old, also i'm interested to use latest armbian-ubuntu-bionic My case: I have a new rockpi4b 1.4v, not eMMC module, I have flashed several armbian versions on sdCard : https://dl.armbian.com/rockpi-4b/Bionic_legacy_desktop https://dl.armbian.com/rockpi-4b/Buster_legacy htt…

Hi, I have tried multiple Rock Pi 4+ (Plus) boards, all of them run regular Debian well, so the hardware should be good. But when I tried Armbian, the 2 USB 3.0 ports were not working with logitech USB dongle or Samsung USB drives (which did work in regular Debian), I searched and found maybe they were in OTG mode and needed to be in HOST mode. I tried armbian-config then System -> Hardware, then enabled: dwc3-0-host rockpi4cplus-usb-host After reboot, the bottom USB 3.0 port would start working, yet the top one still wouldn't work. Otherwise, Armbian was the most user-friendly, fast and stable…

Hey folks, So here's the setup I have: I have an Orange Pi 4B running the Orange Pi 4 image and kernel 5.6.17-rockchip64. I have an Orange Pi 4 running the Orange Pi RK3399 image and kernel 5.4.26-rockchip64 (cause when I got it, the Orange Pi 4 images weren't out yet). The OPi4 is running just fine. I imagine that I'm running the wrong DTB and that not all the hardware is working properly -- but the hardware I need is working just fine. The OPi4B is another story. It'll boot just fine, and it'll run just fine for days/weeks on end -- as long as I don't put it under any sort of heavy CPU load. But if I start running anythi…

Hello! I have OrangePi4 and it works quite well out of the box with Armbian desktop latest. However there were some minor problems, this is the first one: Video resolution was incorrect by default in console framebuffer. The screen is 1920x1080, but default was 1280x720. The solution is adding extraargs=video=1920x1080@60 To /boot/armbianEnv.txt . The part after first = is passed to the Kernel command line and kernel enables the resolution. This have fixed my problem mostly, however, the video output is enabled only during late boot. This is not a big problem, but it would be better if the screen lit up immediately after the computer is powere…

Note that I want to use Hardware acceleration also later, but the issue is that it seems there's no HA for ffmpeg on the chip as you can see here. Thanks in advance!

https://www.armbian.com/odroid-m1/ - kernel 6.1.y LTS

Hi, is is possible to port the kahdas-edge2 changes (https://github.com/armbian/build/pull/6335) to the OrangePi 5b device tree?

Hello, I have a problem, when I enter "sudo apt install zfs-dkms" on my Helios64, I get this error message: "Module build for kernel 6.6.36-current-rockchip64 was skipped because the kernel headers for this kernel do not appear to be installed." I also made sure to install the kernel header in armbian-config and also rebooted. When I type "apt list --installed | grep linux-headers", I get this listing: WARNING: apt does not have a stable CLI interface. Use it with caution in scripts. linux-headers-current-rockchip64/bookworm,now 24.5.1 arm64 [installed] omv7 itself is installed and running. …

Hello, I search the Documentation about LED and Its blinking status. My Board does not anymore boot, Green LED is on (not blinking) red LED is blinking regulary CPU gets very hot and no Screen output. I use the latest armbian image using the following link https://dl.armbian.com/rockpi-4b/Ubuntu_bionic_default_desktop.7z Does anyone have a hint for me Many Thanks Roman

Hi, the latest Bionic Legacy Desktop images for NanoPi M4 V2 (Armbian_20.05.2_Nanopim4v2_bionic_legacy_4.4.213_desktop.img.xz and Armbian_20.05.1_Nanopim4v2_bionic_legacy_4.4.213_desktop.img.xz) do not boot on the board. No green LED. No video output at all. I haven't checked UART. The latest working image is Armbian_20.02.7_Nanopim4v2_bionic_legacy_4.4.213_desktop.7z I have a good power supply (12V 2A, also tried with USB 5V 3A), and a good MicroSD card (high endurance). I did not forget to unXZ the new image file and write it with dd, just as 20.02.7 7z. I've checked the checksum of written data on the MicroSD card, and it equals to the checksu…

Hi, I was trying to load below Armbian images into NanoPi M4 (just M4, neither M4B nor M4V2). They are able to be loaded in the first place, but when I reboot the board by typing "reboot" command in the terminal, I can only see black screen showing on the monitor, no led flashing on the board even, and the board never boots up again. If I unplug the power cable and plug back again, it boots as expected. Is there any way I can reboot the board remotely? Armbian_20.08.1_Nanopim4_buster_current_5.8.6_desktop.img.xz Armbian_20.08.1_Nanopim4_buster_current_5.8.6.img.xz Armbian_20.08.1_Nanopim4_bionic_current_5.8.6.img.xz Armbi…

Hello everyone, I've been running my Helios64 for about 2 months now. My system is installed on the eMMC and i'm running a few docker containers (all from linuxserver.io) Radarr Sonarr Bazarr Transmission Jackett Jellyfin I'm having difficulties with Jellyfin and my media library. When lauching tv shows or movies, the CPU rockets to ~97-99% use and the media is constantly stopping to load. I would like to know what I can do to ease the strain on the CPU and be finally able to use Jellyfin. Has anyone been able to use hardware acceleration with docker ? What info can I give you to shade li…

Having a problem with my board and screen. Recently purchased a couple of inexpensive touch screens that work dandy for pi and lepotato but the resolution on renegade is too high and text just looks like dust on a 7 inch monitor. I took a look at potato xorg driver.conf and there's a lot of modes listed, but on renegade I see: Section "Device" Identifier "NOGPU" Driver "fdev" Endsection And xrandr -- listmonitors output: Failed to get size of gamma for output default Monitors 1 0: +default 1600/423x900/238+0+0. I'm still learning things, but I know exactly how to brick it again 😃. I hope I…

I've tried installing k3s on my OP5Pro and it did not work out because I was missing a couple of things on the kernel. I read the docs on building a new kernel. Did that and was able to get a working 6.1.75 kernel. Even though i got some errors when installing the generated packages. What I did not find in the documents is how I can work on a new kernel. Say 6.11. Has anyone done this? Can you help me out? Thanks! P.D. On a side note. I built this kernel in the OP it self and it was kinda slow. What image can I load in vmware under a macbook air m3 to compile and build faster?

I am attempting to use an arduino uno on a rockpi4 using armbian. The device is connecting but not bringing up /dev/ttyusb0. uname -a Linux rockpi4b 4.4.154-rk3399rockpi4b #26 SMP Mon Dec 10 09:26:20 CST 2018 aarch64 GNU/Linux dmesg [ 98.230808] usb 7-1: new full-speed USB device number 3 using xhci-hcd [ 98.346089] usb 7-1: New USB device found, idVendor=1a86, idProduct=7523 [ 98.346115] usb 7-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 98.346130] usb 7-1: Product: USB2.0-Serial lsusb -t /: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M /: Bus 07.Port 1: Dev 1, Class=root_h…

Hi, I have one FriendlyARM NanoPi R2S. It should have 1G DDR4 memory. Everything works fine with latest Armbian 20.02.08 except only 512M memory shows up. Both Buster and Bionic have the same issue: Armbian_20.02.8_Nanopi-r2s_buster_current_5.4.28 Armbian_20.02.8_Nanopi-r2s_bionic_current_5.4.28 I tried FriendlyARM official FriendlyCore. I can see all 1G memory, /proc/meminfo on FriendlyCore is as follows: MemTotal: 971052 kB MemFree: 842880 kB MemAvailable: 844352 kB Buffers: 8012 kB Cached: 48272 kB SwapCached: 0 kB Active: 45904 kB Inactive: 31580 kB …

Hi, I need some guide and steps required (and if possible) to enable hardware acceleration using FFmpeg. Is the only thing I need since the idea is to use this SBC as Surveillance platform (for example, with Motion+Motioneye or Shinobi). Currencly without hardware accel, using 3 rtsp cams uses each 100% of a core (which translate to 300%). I've searching a lot, but I saw hwaccel with others apps, but not in particular with ffmpeg. I already managed to compile it with --enable-rkmpp (h264_rkmpp hevc_rkmpp vp8_rkmpp vp9_rkmpp) and available hwaccels: vdpau cuda vaapi drm opencl. Any help will be much appreciated. Currently fresh inst…

After installing Arbian on Rock pi 4 c the sound on the Jack does not work because the sound card driver is. 8316 is not supported The sound goes out anyway on the HDMI of my television Would there be a solution

Hello everyone, If anyone would like to have a helios64 without having to wait for the next batch, mine is for sale. This is the complete bundle, it's in very good condition. I will post pictures very soon. I live in France, it would be better if you are in Europe so that the shipping costs remain reasonable...

Hello, I am new to Armbian and Linux and want to set up my raspberry pi camera module 2 for my rock pi4b so I can start doing computer vision work. Does anyone know how to do this?

Please tell me how to build the current bootloader for Rock Pi 4A for booting from SPI?

I have a serious problem as I mentioned in a title Currently I'm using Armbian on my NanoPi M4 and very satisfied its functionality But when I try to use usb3 device (especially camera from ZWO campany, ZWO ASI 178) with it, it doesn't recognize it as USB3 device but USB2 by checking the data transfer speed with "lsusb -t" Then, once I unplug the cable and plug it to the pi again, that device is recognized as USB3 and the data transfer speed becomes much higher. I need to get USB3's fast data transfer as soon as the board gets booted, without unplugging cables since now it's not that easy to access to the board and cable. I tried usb r…

Hi! Unless mistaken, I believe audio is missing from 3.5mm jack on the RockPi4b. To enable it, I had: - To update the dts by adding definitions close to the RockPro64 (some available starting in mainline 5.6) - Change them to use I2S0 instead of I2S1 - Enable audio-graph-card in kernel config (I also removed some audio modules which issued warnings/errors during boot) - Patch es8316.c to prevent a kernel panic during boot (found in Ayufan's latest mainline kernel for RockPro64) yannick@rockpi-4b:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: rockchiprk3399 [rockchip,rk3399], device 0: ff880000.i2s-ES8316 HiFi ES8…

Greetings to all! I want to share the news. 2020.07.21 Mainlinte U-Boot includes patches for Rock-Pi-N10. https://patchwork.ozlabs.org/project/uboot/list/?series=191290&state=* I am trying to build it and run. Everything compiles successfully, but during testing, an error occurs with an incorrect detection of the SDRAM size. On my model A (3GB RAM for CPU), 2 banks are detected at 1152, but it should be 1536. U-Boot SPL 2020.07 (Jul 25 2020 - 09:28:13 +0300) Trying to boot from MMC1 U-Boot TPL 2020.07 (Jul 25 2020 - 09:28:13) Channel 0: LPDDR3, 800MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=14/15 CS=2 Die BW=16 Size=115…

Hello, When it's planned the support of wakeonlan? I want to keep my nas powered off, and power it trough a raspberry pi when I need It. Do you think is planned on the next days or in the next mounths? Thanks

We are facing some issue while interfacing 5" MIPI display to RK3399.

If someone of you likes karaoke I highly can recommend running UltraStar Deluxe (OpenSource SingStar clone) on the Rock Pi 4. https://github.com/UltraStar-Deluxe/USDX I‘ve used the Focal gnome desktop 5.10 image and built UltraStar Deluxe as described. Performance is very good!!! Even with 1080p videos I can‘t see a difference compared to my desktop pc. With the original wireless PS3 SingStar microphones this is a pretty nice and portable setup.

Hello guys! I bought https://aliexpress.ru/item/1005005675856892.html. As I know, there is no 3D acceleration in Debian Bookworm. So, my desigion is to install Armbian Jammy Gnome desktop. My questions are: 1) In what moment should I perform trick ? 2) Legacy is the only system I can install, or is it any way to install current system? I wish kernel v6 to be installed, but not the RC kernel. My experience with SMB is Rapberry Pi 3 B and 4 B. I used to install only Raspbian on that boards. Wish me luck guys :-))

I'm trying to enable UART6, UART7, and UART10 via overlays on a sige5 board. UART6 AND UART7 are working fine but I'm not seeing UART10 in the /dev directory. Could someone help me debug this?

I'm trying to get wifi working on my Rock64 running the nightly server image. Is this possible?

Hi all, I have a Friendlyarm nanopi M4 running armbian, I have tried to install dotnet core without success - anyone here managed it ? I followed a tutorial but when I get to the apt-get install part I see this error Couldn't find any package by glob 'dotnet-sdk-2.2'

/usr/bin/brcm_patchram_plus/rk3399 hogs 100% CPU until rk3399-bluetooth.service is stopped and disabled. The NanoPi Neo3 does not have bluetooth.

I am trying to enable sound with RT5651 audio codec on SoM-RK3399v2. Hardware is integrated on the board (on i2c1 bus, address 0x1a), worked with official FriendlyElec Linux (4.4 kernel IIRC) and tests were run with powered speakers (which work when connected to PC). I used this patch to patch my current device tree: https://github.com/armbian/build/blob/master/patch/kernel/rockchip64-dev/board-nanopi-m4v2-dts-add-sound-card.patch I did not use Kconfig file from the patch as it seems that my kernel have has built that modules. page 19 of NanoPI M4V2 and page 7 of SoM-RK3399 schematic shows that same audio codec (rt5651 on the same busses (I2S1 and I2C1…

Hi, Is TrustZone being utilized at all? I can't seem to find any documentation on what execution level Kobal is running at during boot. I assume it's dropping the Kernel into EL2? Cheers

Hello, I was wondering if the recent update fixed the problem with the lack of gpu support in the OP5 Pro. Thanks in advance.

Hello, Recently the HDD Cable Harness for my Helios64 malfunctioned. SATA Ports 1 and 2 are both no longer getting power/HDDs are not spinning up. I confirmed that it was power by plugging the SATA cable into ports 3, 4, and 5 on the motherboard which all function. I also iterated through the system by removing all the HDD's and testing each HDD slot one at a time. All 5 HDDs fucntion individually in a USB drive enclosure, and all 5 function in my server system and I can mount the RAID array. My question is, does anyone know how to contact the Helios/Kobol team so I can purchase a replacement HDD Harness Cable? …

The Radxa bullseye image looks to boot fine, but Armbian forky does not boot at all.

I received one of these https://www.servercase.co.uk/shop/server-cases/rackmount-case-accessories/accessories-spare-parts/supermicro-cse-m14tqc-cse-m14tqc/ today to go with the Nanopi M4 SATa hat, it has a male Molex for input power, the SATA hat has a male Molex power outlet so I need a female to female Molex connector which I can't find anywhere - any ideas guys ?

To try the new goodies I've tried to install Buster Legacy on my M4V2 but it always hung on [---] A start job is running for Bluetooth Rockpi (many minutes / no limit) https://redirect.armbian.com/region/EU/nanopim4v2/Buster_legacy_desktop I downloaded it multiple times and no change. I'll try the mainline image and then regress kernel to legacy.

I haven't been able to find any specs on the eMMC module in the helios64. I've found some posts online indicating that it is a samsung KLMAG1JETD-B041, but I haven't been able to find any info on the write endurance of this module (not sure if it is standard for eMMC vendors to provide that information like SSD vendors). I have been able to run `mmc extcsd read /dev/mmcblk1`, which shows that the emmc life time estimation is between 0 and 10%, but since this value is in 10% increments, its not very helpful. I've had issues with the default ramlog-based /var/log, so I had to turn it off. I've increased the size to 250MB but it regularly fills up b…

hi everyone How can I activate the SPI in the nanopi neo3 board?

Hi, I am strugling with the OV13850 camera on the NanoPC T4. Its working with the command : GStreamer 1.1 command: gst-launch-1.0 rkisp io-mode=4 path-iqf=/etc/cam_iq/rk-ov13850.xml ! video/x-raw,format=NV12,width=1280,height=720,framerate=30/1 ! rkximagesink But I can not connect to it through OepnCv VideoCapture cap(0) . or 1 2 3 . It give s error : VIDIOC_QUERYCTRL: Inappropriate ioctl for device Is there anybody experienced on this ? thx

Hi, I have one silly problem developing a FBTFT device driver for SSD1322 display : https://github.com/MarkoBursic/fbtft---SSD1322/blob/master/fb_ssd1322.c The initialisation starts OK, all GPIOs (DC, RESET, CS) follows as they should, since the data is sent through a function write_reg. For example : write_reg(par, 0xA0, 0x14, 0x11); It asserts DC low, then sends 0xA0, then asserts DC high and sends 0x14 and 0x11. Within every sent character (8bit bata) the CS toggles. The problem becomes when I want to send video data, I guess a function write_vmem is called. But here the entire tx buffer is filled and then streamed. for (y =…

Hallo, I've been using Armbian on the NanoPi M4 V2 for a while and now I'm thinking about switchen from the legacy kernel to the current kernel. Unfortunately that's not so easy to do when using armbian-config. You could think you can just select the current-kernel in the list but you won't find it there. The reason is simple: the legacy kernel belongs to the rk3399-family and the current kernel is rockchip64. Which is basically the same, but from an organisational point of view it is not (please forgive me if I do not show an adequate technical precision here, the details and the plan to clean that up are explained here). What I would be intereste…

Hi guys! I would like to know why this is happening. I guess the script doesnt identify my sd card as the sd card and it erase it just like it does with emmc before clonning the sd card to the emmc. I use latest armbian focal.

Hello, target : nanopi R4S/4Gb I downloaded the last image from the armbian site for the friendlyelec nanopi RS4. I flashed an A1 SD card of 32GB. I only see one partition (after a 17MB offset). When I try to use it on my R4S, the red power led lights up, then nothing, even after several minutes. I opened the router and connected a serial converter on the console, in this case also there is no sign of life after the power on... I have flashed on another SD card an ubuntu image from the friendlyelec site. This image boots, but it seems that the configuration of the console is not the usual default one => the speed 115200 does not w…

Hi, An old problem, since I got the board which is 4C. Not a + - or whatever but the plain C. Symptoms: 1. HDMI worked randomly, maybe every 10th...15th boot lead to a working system, or rather to a visible HDMI-connection. But now switching on-off does not help at all. 2. Quite often one can get the board booting to the point where it asks for the password, and after clicking ok, it switches the screen off, and won't return. So the telly says that "no signal". 3. When switching on the board the tv set sees that there's someone on the hdmi port, and shows the booting sequence, and finally goes to Armbian's graphical mode asking for t…

I am trying to get a RPi camera (imx219) working on a RockPI 4C. I have been piecing together DTS files from various places trying to make sense of it, and I noticed that the rkisp kernel module isn't compiled on the Rockchip64 kernels. Is there a reason for this or am I missing something? Looking at the kernel menuconfig, only one of its dependencies isn't compiled: `V4L_PLATFORM_DRIVERS=n`.

I tried the latest 6.8 kernel edge on my Rock 5A and noticed the CSI camera interface doesnt exist. Is there any plan or time schedule to fix that? I saw it's marked "TODO" on https://gitlab.collabora.com/hardware-enablement/rockchip-3588/notes-for-rockchip-3588/-/blob/main/mainline-status.md . So in 6.9 perhaps? (A LOT of other stuff works remarkably well though, great work!)

I have some questions about the Linux images that Ayufan built for the Rock64 board. Not really technical issues so I did not think they should go on the Github page. If this is not the appropriate place for these, let me now and I'll remove this post. Also, if this is not the place, where should I be asking these types of questions? I just downloaded the new PRE-RELEASE version of Debian Stretch from the Github page (Yes, I know it's bleeding edge, but just experimenting for now). Specifically the stretch-minimal-rock64-0.6.5-152-arm64 image. I just burned it to my eMMC board. Will boot and see how it all works tomorrow. There are a number of…

Hi all. In download section i do see "large heatsink required" for Rock64. Can anyone post any links to eamples of good heatsink with proper size ? I will be migrating "home server" from Cubieboard2 to Rock64 and chasing long-term stable operation. When board just booted and "does nothing", cpu remains pretty cool. However i'd better be prepared. thanks in advance for tips.

Hi i have a orangepi 4 , i try install armbian mainline based kernel 5.4.y having issue with hdmi, no display, the os cant sense any hdmi connection. But when i try kernel 4.4 the hdmi work with? anyone having the sane issue?

Dear all I have a question concerning the Tinker Board video playback function. Until now I used some raspberry PIs 3b to create a simple system that video playbacks in loop after booting for my video installations. Now as the raspberries are not in stock at the moment but i need very urgently another working system, i saw that i can buy the tinker board 2.0 for a reasonable price. However, I'm not a programming specialist and was happy when I got the raspberry to run, I couldn't found anything about the tinker board and specially about a video loop function. I imagine that it is possible, just wondering how complicated it is. Can someone tell me …

Now I'm no expert but I got Mate working maybe there are some shortcuts I did not take, but it works great. So feel free to point out any flaws or improve it, #!/bin/sh -vx packages=' cryptsetup libblockdev-crypto2 engrampa firefox ffmpeg libavcodec-extra gufw lightdm lightdm-settings slick-greeter ubuntu-mate-wallpapers-common mate-desktop-environment-extras mate-applet-brisk-menu mate-applets mate-calc mate-indicator-applet ayatana-indicator-application ayatana-indicator-bluetooth ayatana-indicator-common ayatana-indicator-display ayatana-indicator-keyboard ayatana-indicator-messages ayatana-indicat…

Hello, I ran sudo apt update / suodo apt upgrade on my Rock 3C this morning. I did notice that the kernel was upgraded but rebooted. It transpires that the kernel was upgraded to a completely new version (6.12.9) from 6.6.63 (or 62 I believe).

Hi, I want to know if there is another way to power the Nanopc-t4 besides the 12V input power jack. As far as I know the 12V power input is the only way but If someone have another idea or way to do power the board, it could be very helpful for me. Thanks.

I've been following this thread: https://forum.openwrt.org/t/nanopi-r6s-linux-6-3-arm-soc-updates/153072/14 downloaded the latest version. Decided to do some experimenting and found out that they use u-boot 2023.04. And after some experimenting I found out that it works with Armbian when I flash it to the internal storage. U-Boot 2017.09-armbian (Apr 25 2023 - 04:20:41 +0000) U-Boot SPL 2023.04-OpenWrt-r0-e283eb2 (Jun 12 2023 - 00:36:27 +0000) Whats the reason the armbian u-boot is so far behind ? (i know its WIP, just asking)

Hello everyone. I want to try to connect a custom AMOLED DSI display with orangepi 3b https://www.phoenixdisplay.com/product/color-displays/oled/at043qhd3008/ And there is practically no information. Maybe someone has seen or encountered similar problems? Do I understand correctly that the dts section on brightness adjustment does not need to be written, because AMOLED as such does not have a backlight? Is it possible to run such a display using simple-panel-dsi? Another interesting question is how to organize the power supply for such a display? It needs different voltages from 1.8 to 4.6 V

Hi all, https://paste.armbian.com/koqimivaro vendor kernel boots, detects ethernet, wifi & nvme (booting from SD card) and seem to be working well. Also attached are the UART gathered first boot/install logs. I think the SBC accidentally skipped over the root password by resting on the enter key 😁 uart-logs.txt

TL;DR: How to make HDMI screen with custom resolution work? Including boot log/boot splash screen. How to configure auto use of/auto switch to newly connected display? Means moving tty/X Session to connected display like it works on e.g. Ubuntu desktop. Why HDMI screens with non standard resolution works well on kernel v5.x but stop working on v6.x ones? Where are HDMI related I2C interfaces in Armbian? Full version: In theory host system (SBC, laptop, PC) should detect new HDMI device connection, load EDID data from screen and use it to configure video output (resolution, timings etc). In practice it works well for Ubuntu deskto…

There is a uwe5621ds WiFi module on my rk3576 development board. I burned the system image of armsom-cm5-io. After booting, calling the modprobe sprdwl_ng command will encounter the following kernel pannic [ 71.088504] Unable to handle kernel NULL pointer dereference at virtual address 00000000000001d0 [ 71.089376] Mem abort info: [ 71.089655] ESR = 0x0000000096000004 [ 71.090002] EC = 0x25: DABT (current EL), IL = 32 bits [ 71.090490] SET = 0, FnV = 0 [ 71.090784] EA = 0, S1PTW = 0 [ 71.091069] FSC = 0x04: level 0 translation fault [ 71.091509] Data abort info: [ 71.091772] ISV = 0, ISS = 0x00000004 [ 71.092147] CM = 0, WnR = 0 [ 71…

Hi folks! Some problems later I just build my ethereum-node using the FriendlyARM NanoPC T4 (Reddit project Ethereum on NanoPC T4). Using it indoor the temperature climbs to 80° celsius with the passive cpu-heatspreader. So I decided to install a fan and found the specs for the 'Cooling Fan interface'. The connector is named BM03B-GHS-TBT. Where can I buy a fan (40x40mm)? I only find fans with 3-pole-molex-adapter. All I know is the name of the male connector (in german): "JST Buchsengehäuse-Kabel GH Polzahl Gesamt 3 Rastermaß: 1.25 mm GHR-03V-S".

Hi, when I used rsync to copy several GB of data from the NMV3 to a USB SSD, the SSHD crashed. [96500.101926] ------------[ cut here ]------------ [96500.102376] kernel BUG at arch/arm64/kernel/traps.c:405! [96500.102858] Internal error: Oops - BUG: 0 [#2] PREEMPT SMP [96500.103343] Modules linked in: sg uas hci_uart bluetooth cpufreq_userspace zstd zram dw_hdmi_i2s_audio rockchip_rga v4l2_mem2mem videobuf2_dma_sg panfrost fusb302 tcpm videobuf2_memops gpu_sched typec videobuf2_v4l2 videobuf2_common videodev mc brcmfmac brcmutil cfg80211 rfkill rockchipdrm analogix_dp dw_mipi_dsi dw_hdmi ip_tables ipv6 crc_ccitt phy_rockchip_typec phy_rockc…

hello everyone I have this board orange pi 4 V 1.3 Armbian Focal desktop mainline based kernel 5.4.y . I haven't audio through HDMI. what can I do ? I ran the media script for hw acceleration and i have good video result but not audio. Thx!

Hello, After facing multiple instabilities during previous week, I decided to completely reinstall my helios64 to a fresh image (bookworm) from the download section. But before doing that, I need some help/have some questions: Currently, I’m using emmc to host the system, how can I completely backup and restore the system on an sd-card (you know, just in case...) Does the current image (https://dl.armbian.com/helios64/Bookworm_current_minimal) already contains usb drivers from:and this dtb file: Does the process to install the new image on emmc is the same as the one documented on Kobol site? At the moment, I’m a little bit los…

Hello guys, does anyone activated CVBS output on Rock64 board? After a short look into datasheet Rock64 should support 480i and 576i. Many thanks.

Gentlemen, I have a rock64 board, and I would like to use an external RTC module with DS1307 chip. Unfortunately the armbian kernel does not provide DS1307 driver by default: root@rock64:~# cat /boot/config-4.4.162-rockchip64 | grep DS1307 # CONFIG_RTC_DRV_DS1307 is not set I don't have the programming skills for sending a pull request to enable this module. Could you please enable this module for ROCK64? I believe other ROCK64 owners may also benefit from this driver, as the board does not expose a working RTC, and DS1307 is a very common RTC chip. Thanks in advance.

Hello, can someone help me with my problem. I have a ROCK64 with 4GB of RAM and an ARMBIAN 5.75 stable Ubuntu 18.04.2 LTS 4.4.174-rockchip64, installed. My issue come with usb ports, from the three USB of the this device only works two: one 2.0 and 3.0. And when i have a disk connected towards usb 3.0 i have issues with port usb 2.0, it doesn't work well and I end up disconnecting the USB 3.0 to can work with my device connected towards USB 2.0 so I assume that the current power on the USB port is having issues or it's not working well. Anybody an idea? thanks!

I'm trying to install wiringpi by following the instruction given here https://github.com/Pavelectric/WiringPi_M4. Most of the steps that I followed worked fine but when I do the very last command below, I get a following error, I googled how to deal with this kind of error, and some people tell that 'ContextualZipFile' in archive_util.py doesn't have to be installed so I just need to comment that out. Although, I couldn't find '/usr/local/lib/python3.6/dist-packages/setuptools-33.1.1-py3.6.egg/setuptools/archive_util.py', I did that comment out solution to the all files below, which I got by doing find-command-research Now I d…

I just received my Helios64, I immediately checked it for the Magjack center point to ground concern, and mine tests that it is connected. Is there a revision number on the board which can be used to identify the clean point between the pre and post fix boards?

Hi Distro Debian Buster, Linux rockpi-4b 5.10.21-rockchip64 #21.02.3 SMP PREEMPT Mon Mar 8 01:05:08 UTC 2021 aarch64 GNU/Linux I trying run HDMI-CSI bridge (auvidea B101) with board RK3399. Driver is loaded but dmesg not see any communications. root@rockpi-4b:/home/stream# lsmod |grep tc tc358743 40960 0 v4l2_dv_timings 36864 1 tc358743 v4l2_fwnode 28672 1 tc358743 videodev 299008 8 rockchip_vdec,v4l2_fwnode,videobuf2_v4l2,hantro_vpu,rockchip_rga,videobuf2_common,tc358743,v4l2_mem2mem mc 61440 7 rockchip_vdec,videodev,videobuf2_v4l2,hantro_vpu,videobuf2_common,tc358743,v4l2_m…

Hi guys. I've been working with the 4.19 kernel before on M2. I upgraded to the kernel version 5.18 today. I found that I can't find the registered udc device anymore. This is auto-registered on the 4.19 kernel and you can find it under /sys/class/udc. root@station-m2:/boot# ls /sys/class/udc fcc00000.dwc3 I would like to ask how to enable the udc device on the 5.18 kernel. Thank you.

[ 11.309397] panfrost ff9a0000.gpu: clock rate = 500000000 [ 11.316882] panfrost ff9a0000.gpu: EM: OPP:200000 is inefficient [ 11.317248] panfrost ff9a0000.gpu: EM: created perf domain [ 11.320588] panfrost ff9a0000.gpu: mali-t860 id 0x860 major 0x2 minor 0x0 status 0x0 [ 11.321594] panfrost ff9a0000.gpu: features: 00000000,00000407, issues: 00000000,24040400 [ 11.322812] panfrost ff9a0000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 [ 11.324483] panfrost ff9a0000.gpu: shader_present=0xf l2_present=0x1 [ 11.357056] [drm] Initialized panfrost 1.2.0 20180908 for ff9a0000.gpu on minor 1 It seems Panf…

I have an orange pi 5b running Armbian_24.2.1_Orangepi5_bookworm_legacy_5.10.160_cinnamon_desktop on EMMC just fine. i wanted to try a newer version with hardware acceleration so i tried Armbian_24.11.2_Orangepi5_bookworm_current_6.12.0_cinnamon-backported-mesa_desktop. I edited the file in the boot folder and could see the EMMC on reboot. i did a sudo apt update and sudo apt upgrade. then an armbian-install to install it to the EMMC. it would not boot from the EMMC but i could at least still see it. Then i tried Armbian_24.11.2_Orangepi5_bookworm_vendor_6.1.75_cinnamon-backported-mesa_desktop and did the same but now i cant see the EMMC even with the ori…

Hi, Just received my Nanopi R5C. Flashed the Debian 12 (Bookworm) Minimal/IOT images with Armbian Linux v6.12 from here https://www.armbian.com/nanopi-r5c/. Everything works well except that I could not get the WAN port working. Anyone has any idea? BTW, the Nanopi R5C looks different from the image showed on https://www.armbian.com/nanopi-r5c/. Mine has only 2 x 2.5Gb ports instead of the 3 port. The image on the page looks like a NanoPi R5S... Just a side note. Cheers.

Your build Armbian 5.65 kernel 4.4 and my build 5.65 the same kernel - system has sound only via HDMI monitor. Is it possible to enabled audio via 3.5 jack or external USB sound card?

Hi, the rockchip64 missing the gre modules for ipv4 and ipv6. they had been existing in 4.4.156-rockchip64 /lib/modules/4.4.156-rockchip64/kernel/net/ipv4/gre.ko /lib/modules/4.4.156-rockchip64/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko /lib/modules/4.4.156-rockchip64/kernel/net/ipv4/ip_gre.ko /lib/modules/4.4.156-rockchip64/kernel/net/netfilter/nf_conntrack_proto_gre.ko /lib/modules/4.4.156-rockchip64/kernel/net/ipv6/ip6_gre.ko is it possible to add these? thx in advance meno

Hi all! I'm having strange issue with Rock64. I downloaded latest Armbian 5.88 with 4.4.180 kernel. Installation and boot are ok, but when I try to do apt-get install lvm2 Package installs, configures and... update-initramfs: Generating /boot/initrd.img-4.4.180-rockchip64 update-initramfs: Converting to u-boot format Then I do root@rock64:~# sudo reboot And I'm getting a boot loop... Same effect, if I move system to SSD. At first I thought it was issue with ssd transferred system... But it clearly reproduced on freshly written with uSD only boot. I've dumped armbianmonitor output (ju…

Hi, I am trying to setup NVME boot on RockPI 4 c. I have tried different things, but no success. First I have installed Redxa SPI last u-boot image over OTG. Download last Armbian for Rock pi 4 c. ( Own building last Armbian for Rock P4 C trunk from 10/28 5.8.16 , I had tried too ) Install image on SD Card. ( dd ) Boot from SD card. Copy Image over scp to SD Card. Copy image with dd to NVME. Shutdown and remove SD Card. Boot from NVME ( Works on ever try ). Login and change password. Add one user. Shutdown and try to reboot. The System never reboot. The serial console shows. 64.495100 nvme nvme0…

I have a problem with remote desktop operation on R4S. It installs according to the RDP guide and unfortunately does not work properly, after installing vncserver I also have information about - Cannot find a running X server. Everything works fine on neo3, only here I have a problem. Log VNC xstartup terminated Sending TERM signal to Xvnc... X connection to :1 broken (explicit kill or server shutdown). FreeFontPath: FPE "/usr/share/vnc/fonts/" refcount is 2, should be 1; fixing. <13> 2021-03-16T17:40:30.716Z nanopi-r4s Xvnc[5435]: ServerManager: Server stopped Link Status R4S Please Help 1) Armbian_21.02.3_Nanopi-r4s_focal_curren…

Hi, I use Helios64 from the begin and this board is very unstable according to my experience and many posts here... After many dialogue here and settings shared about Frequency and Governor Kernel... maybe i find the problem and i ask anyone return of experiences about the procedure and setting belong: - Connect USB Wireless Dongle or USB(-c) Ethernet Plug - Configure it - Disconnect all ethernet cable to the board - Use with last time crash configuration and do a endurance test your helios64 board Have a good day

After recent kernel update, USB3.0 ports no longer work, There is an error printed in kernel log. [ 2.826383] phy phy-ff800000.phy.6: phy poweron failed --> -110 [ 2.827119] dwc3 fe900000.usb: error -ETIMEDOUT: failed to initialize core [ 2.827881] dwc3: probe of fe900000.usb failed with error -110 I found this issue in NanoPC T4, but it might also appear in other RK3399 boards. lsusb didn't show any USB3.0 controller. Confirmed this isn't my hardware's problem, another board have this issue too. dwc3.txt

Libre Renegade overlays opp-1.4ghz and opp-1.5ghz load but not working in trixie edge (24.5.0-trunk.512). Both overlays do work in 24.2.1 bookworm.

Hi team, This is not exactly Armbian related, however I hope to find some help here, also it can be useful for someone else in custom board development (my case). For testing I have Olimex RK3328-SOM-EVB and RK3318 TV box boards. They both behave the same way. As summary I'm trying to boot Linux using the Bootrom and USB OTG only, in other words without any external boot NVM attached. To archive this I build U-Boot SPL (u-boot-spl.bin), which support SDP protocol via USB OTG. For SDP file transfer I'm using imx_usb tool. The binaries used in the process are: rk3328_uboot_v1.19.250.bin - consists of u-boot-tpl.bi…

As I reported here (https://github.com/armbian/build/issues/1230), I'm seeing frequent reboots and Kernel Panics on a RK3399 board while running ElasticSearch, a kinda heavy application that runs on Java. I currently run a Kubernetes cluster on two RK3399 boards (NanoPC-T4). One of them I has a version of DietPi with a Kernel 4.4.138 compiled by myself. and runs perfectly. The other had a newer version of a Kernel (4.4.154) also compiled by me and that's where I started seeing the reboots. After this, I installed Armbian thinking it might be something with my DietPi distro. I installed 5.69 with Kernel 4.4.167 and saw the same problems. I did a ful…

Hi. I am kind of linux newbie. I want to use serial console with my Rock Pi S thru usb otg. I googled and found this from https://gist.github.com/lukicdarkoo/a87f79b1c25cd86bdc47a8784d6eee9c. I tried it but failed. And I found that there was not "sunxi_usb_duc" directory. Any advice would be apreciated. =============================== ok, I just found that these are for orange pi. Any guide for rock pi s? =============================== After install new image, now I can use serial console with usb otg.

Hello My Helios64 arrived two weeks ago, after a loooong trip through the Silk Road all the way down to South Europe. First thing I want to give a GREAT THANK YOU to the people at kobol shop support, as they have helped me with my transport/forwarded/ carrier nightmare loop: the address is in Chinese-no address specified-contact the sender-won’t give you your parcel-please call again- no address specified.... So. After reading a good slice of the wiki I couldn’t find a comprehensive manual/article about the simplest usage of the front panel. Glad if you can point me to such information. The principal source of confusion for me are the comments section of …