Allwinner sunxi

Hi guys, I know cubieboard A10 is already out of support, nevertheless I was able to make the right image work for it with a cubiescreen. Armbian gave me a way to make my own image without so much problems. The only issue I am having right now is that my touchscreen stops working after a while with errors like this: msg ft5x_i2c_rxdata i2c read error: -121 ***CTP***ft5x_read_data:893 read_data i2c_rxdata failed: -121 bus is busy, status = f9 Retrying transmission 2 I asume that my kernel patch for this touchscreen is not longer working. I have found that some guys manage to make it work under kernel version 3.4.79. So I tried to c…

Hi there, after upgrade Armbian today the Device (banana-pi) doesnt come up again telling that the root fs couldnt be mount because mmcblk0p1 is not available. After checking SD Card everything seems ok, filesystem is there and doesnt have any error. But still no boot. Then after applying a backup things are fine again. Started the upgrade again and same error like before. When applying those two updates there is repeatedly a dead system afterwards. Tested on different devices now. root@gluster01:~# apt list --upgradable Listing... Done armbian-config/unknown 25.5.0-trunk.330.0402.205255 all [upgradable from: 25.5.0-trunk.286.0324.065110] linux-ima…

Hello, I am trying to have a serial link between an arduino and a banana pi. As a basic test, the Arduino is sending "hello" every seconds. I observe that the reception by the Banana pi is not good. I have tried , several baud rates, /dev/ttyS2 and FTDi adaptor. The best result seems to be with the FTDI adapter , at 115200 bps. But I have still a lot of errors, see below. When I plug the FTDI adapter on my laptop, it works without issues. Do you know what could be the cause of my issues? Thank you Sebastien hell»½ýhgn·ïÏÞh»½ëèu·oÝÕýemmÍÿÿý¿¿ëÏÿÿýïï»ÿ½{í»ÿ¯nïÿý{¿ûoïÿÿÿÝÿïÏíumío^huw·oMÕh…

Hello, do you guys havea proper device configuration file for crosscompiling Qt apps to Armbian on my opi one? Couldn't find one online and the multitude of flags frankly confuse the heck out of me.

Hi, I would like to know if it is possible to limit USB speed to 1.1 standard on orangepipc and how to do it? I know it is doable on raspbian but I couldn't find info about doing this on armbian

I've tried many permutations of overlays and user-overlays and I can get /dev/spidev0.0 or /dev/spidev0.1 to be present, but I can't seem to get both simultaneously. I need both to migrate a project from an older Fedora distribution relying on modprobe to the latest version of Armbian. Any suggestions will be greatly appreciated! I started with very recent Armbian 23.02 Bullseye XFCE downloaded from arbian.com/banana-pi-plus .. Armbian_23.02.2_Bananapi_bullseye_current_5.15.93_xfce_desktop.img and I added the following to the /boot/armbianEnv.txt file, as described in the Armbian page associated with the BananaPi M1+ .. f…

Dear maintainers, I have my sensors configured to reboot every night via a user cronjob (0 0 * * * /sbin/reboot), 14 sensors do this without a problem. I've fixed the nanopi neo+2 reboot from NAND some months ago (by re-using friendlyarm first stage u-boot). I just stumbled upon a failed reboot with one of my nanopi neo+2 nodes, after two successful reboots. Looking at the /var/log.hdd/syslog, it got stuck in the shutdown procedure when the watchdog reported a failure. The /var/log.hdd/syslog.1 extracts below show the start of the watchdog, and the stop of the watchdog and its failure. After the failure the system doesn't come up anymore, it needed a pow…

Hi, I found a similar thread about space problem on /boot when upgrading the kernel, but it was with debian jessie, not Ubuntu, and the proposed "trick" doesn't seem to work anymore: This is what I get: Actually, I am facing this problem since I set up my system a year ago, but didn't take the time to solve it. But now, I would like to finish the aimed set up of the device (home server) and would like to get this out of the way. Thanks for any suggestion.

Hi, I've tried to finally move on from 5.04, but the new image doesn't boot. At least, HDMI doesn't show anything and my router doesn't see the board when connected via ethernet. On the first power-on the green led glows a few minutes, then red one blinks a few times alone, then both leds blink and then only green one glows. On successive boots only green led glows uninterruptedly. Do you need any information to make it work? BTW, legacy kernel worked fine for me, except my HDD connected with hdd-usb adapter (Agestar 3FBCP1) spits errors every few seconds and performance is unbearable. Connected to my router with TomatoUSB the same hdd works fine. I hoped n…

Hi to All, I am proud to announce that our effort to embed Olimex' Lime2-eMMC board in Application Controller for Ground Penetrating Radar (GPR) systems meets with success to the final phase. Our product EGPR (Easy Ground Penetrating Radar) is ready for demo and field tests. Everybody can take a look on our just finished web site. There is link to the real application from Demo page. We would like to express our gratitude to Armbian project, its whole team and everybody here in for the great effort and help. Best regards EGPR team

Got this when I do an apt-get update root@nanopineo:~# apt-get update Hit http://security.debian.org jessie/updates InRelease Ign http://httpredir.debian.org jessie InRelease Hit http://httpredir.debian.org jessie-updates InRelease Hit http://httpredir.debian.org jessie-backports InRelease Hit http://security.debian.org jessie/updates/non-free armhf Packages Hit http://httpredir.debian.org jessie Release.gpg Hit http://security.debian.org jessie/updates/non-free Translation-en Hit http://security.debian.org jessie/updates/main armhf Packages Hit http://security.debian.org jessie/updates/contrib armhf Packages Hit http://httpredir.debian.org jessie Release Hit http://sec…

hi guys I'm amateur Linux user. now i can connect to internet with WiFi but i don't know how connect to internet via LAN (Ethernet) my problem is Ethernet setup . please help me for make small network with 2 or 3 client With the ability to share internet and file. my boards : 1 orange pi PC plus( Intended for server ) , 2 orange pi Zero 512Mb ( Intended for client ), network Components : LinkIt Smart 7688 (WiFi to Ethernet Bridge ) D link 8 port switch I'm so sorry for bad English

Hi All Please can someone assist me. I'm at my wits end here. I have an Orange Pi Lite running Armbian 5.30 desktop edition. I want to rotate the display 90deg. I have had no luck with xrandr as it lists the display as 'default' and not a specific output and this seems to cause a problem. The option to rotate the display is also not available in the display manager. Thanks in advance.

Hi, I'm want to use my old Nanopi Neo Air with CAM500B as wifi webcam. I flashed the latest armbian bionic image, installed v4l-utils and tried to list the cameras properties with `v4l2-compliance` and `v4l2-ctl --all` but the tools always crash and I can't kill them. `dmesg` shows a NULL pointer exception: [ 56.994526] 8<--- cut here --- [ 56.997657] Unable to handle kernel NULL pointer dereference at virtual address 00000068 [ 57.005825] pgd = c774af94 [ 57.008606] [00000068] *pgd=00000000 [ 57.012243] Internal error: Oops: 5 [#1] SMP THUMB2 [ 57.017122] Modules linked in: brcmfmac brcmutil sun8i_codec_analog sun8i_adda_pr_regmap su…

Hi everyone, today I notice that my orange Pi one stopped (crashed) yesterday, how to prevent this next time ? Is the watchdog a solution to the problem? or please advice are there any additional parameters or details I need to know for using watchdog ?

Help with connecting the camera. I have already tried many different images and means, but I never managed to launch the CSI camera. Someone was talking about the 3.4 linux kernel on armbian to make it work, but I don't know where to find it. Can anyone have an image on which the camera works?

ARMBIAN 5.31 stable Ubuntu 16.04.2 LTS 3.4.113-sun7i Cubietruck a few years old device (dual core, 2GB RAM). /boot/script.fex: [gpio_para] gpio_used = 1 gpio_num = 4 gpio_pin_1 = port:PH20<1><default><default><1> gpio_pin_2 = port:PH10<0><default><default><0> gpio_pin_68 = port:PH18<0><default><default><0> gpio_pin_69 = port:PH24<0><default><default><0> According to http://docs.cubieboard.org/a20-cubietruck_gpio_pin there is no PH20 but PC20 echo 1 > /sys/class/gpio/export echo in > /sys/class/gpio…

After receiving several Orange Pi Zeros and a Pi+2E, I have been experiment on different ways to connect them using the g_ether and usbnet modules, and configuring the Zero OTG port as slave (mode 2). My last attempt was to use the Pi+2E as a data concentrator, connecting three different OPIZ on the independent USB channels, creating ethernet over USB links ... this have been my week's nightmare. By now these are my findings (could change with more information at hand). 1) The Pi+2E enables 4 different usb ports. The usb0 is the OTG microUSB port, and the usb1, usb2 and usb3 are the other exposed type A USB ports. 2) The usb0 has a particular MAC Address and…

Hi, I tried to safe-upgrade (apt-get upgrade) Trusty today but got the following notice: Failed to fetch http://apt.armbian.com/dists/trusty/main/binary-armhf/Packages It would be OK to dist-upgrade to Xenial anyway as described in the Docs ... apt-get install update-manager-core do-release-upgrade -d # further to xenial apt-get dist-upgrade ... but I think it would be a good idea to start from a proper Trusty. Any suggestions. Thanks in advance Mark

I had working Banana Pi -> I compiled latest kernel (all config were default) and installed it -> Banana Pi did not boot, it was stucked on "Raising network interfaces" -> I downloaded latest image (Debian Jessie) and flashed it on SD card -> Banana Pi still stucked on "Raising network interfaces". Banana Pi is connected via normal cable directly to the router with DHCP. I have also tested cable and router and tried to use different cable. I have not changed anything else.

Hello, I am using OPI one with Armbian_5.90_Ubuntu_bionic_4.19.57, so I fliped my 7" touch screen display vertically (rotated 180) by modifing: /etc/X11/xorg.conf/01-armbian-defaults.conf and it worked, but the touch doesn't correspond with it (still points as it was before rotation). how can i flip the touch information (x,y) coordinates vertically (rotate by 180)? Regards,

I am trtying to keep my pcduino 3 nano alive. It has been working perfectly under a debian bullseye distro from Johan Gunarsson for 4 years and now I can't get the OTG to work under any release (bullseye, bookworm or trixie) I have explored many avenues, but even a plain manual setup of g_mass_storage doesn't work in a workable way. The drive appears in Windows Explorer after several minutes, and any copy or delete to that gadget drive takes ages (3+ minutes for a 12kb file) before it fails or succeeds silently. I am looking for a forum where pcduino users can help each other. Thank you, Gaetano.

I'm using wiringPi installed from here, it works fine for the most part but when I try loading spi it throws the following error: modprobe: FATAL: Module spi-sun7i not found in directory /lib/modules/3.4.113-sun8i gpio: Unable to load spi-sun7i FYI: I'm using Armbian 5.31

the nand-sata-install always proposes the sda1 as a destination. this did not fit what i needed. i have had success by editing the file and replace all sda1 with sdxx (whatever i need) and then it works (the information gives the wrong size in the initial screen). i looked into the code (but i do not understand bash programming): it seems that sda1 is hardwired despite the intention to find all possible destinations and to offer them. it is a useful utility, as it does several things at once (copy stuff, change fstab) which are otherwise separate coordinated steps. thank you for the utily! andrew install into nand did the correct copying, but did not …

Hi, i am new here and like to say hello. On my new cubietruck I have one after another tried to install and use wheezy and jessie with legacy and vanilla kernels. With the legacy versions i failed because there seemed to be no video-output on VGA from the kernel. The boot-process seemed to be stopped after Starting Kernel. Then i found that it was visible on HDMI but not on VGA. Because I have only VGA-Screen on my desk i went on with vanilla jessie. But on the download-page there is the note "No audio or accelarated video". What does it mean in detail? I installed mplayer but in fact there is no sound at the jack. Isn't therefore any driver available? Which …

Hi, I'm facing a problem with my Orange Pi Zero with the latest Armbian version. I noticed that when I provide an internet connection type that is not valid (wrong psk, ethernet but no cable plugged in, etc.) and I reboot the system, it hangs just before asking the username and password. Sometimes it takes up to 10 minutes before keeping going. These are the last boot logs that I see: [ 11.209226] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 11.219428] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped. [ 11.244988] systemd[1]: Started Nameserver information m…

Hi all, i am trying to enable UART4 on my Cubieboard2 via /boot/armbianEnv.txt: overlay_prefix=sun7i-a20 overlays=i2c1 uart4 param_uart4_pins=a but if it seems that my uart4 is not working. If i look at dmesg | grep tty there is no ttyS4-device - only ttyS0: [ 0.000000] Kernel command line: console=tty1 root=/dev/mmcblk0p1 rootwait rootfstype=ext4 sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_no_mali_mem_reserve sunxi_fb_mem_reserve=16 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 enforcing=0 loglevel=1 [ 0.000860] console [tty1] enabled [ 1.542600] 1c28000.ser…

Hello, I am trying to use BPI with legacy Armbian and Stella emulator with 16:10 monitor (using HDMI-DVI cable) I just dont know how to set proper 16:10 resolution. The resolution I set in armbian-config is 1680x1050, but it is different from resolution that Stella uses, when I launch it on the startup. It uses the resolution defined in FEX. So I checked https://linux-sunxi.org/Fex_Guide#disp_init_configuration and tried various resolutions, but dont know which of them is 16:10 and what is the exact resolution. For example 576p can mean anything. How can I find it out? Thank you very much.

Hi! On my Banana Pi PRO, i installed this «Armbian_5.00_Bananapi_Debian_jessie_4.4.1» but applications report 'no soundcards found'. I did the apt-get upgrade for 5.01 but still same problem.

Is the build for Orangepi Plus the same for Orangepi Plus 2? When I download for OPI Plus 2 I get the following file: Armbian_5.65_Orangepiplus_Debian_stretch_next_4.14.78 but it will not start

Hi! Thanks for your amazing work, i'd like to have knowledge to give a hand After a few problems I've been able to boot my new Orange Pi Prime, but no keyboard is working on it. I've tried with an USB keyboard and a bluetooh one, but there is no way to make them work. No clues on dmesg, lsusn looks fine... Any idea about hoe to debug it?

I think I messed something up in the system, maybe with the repositories, but I get this message when updating... apt update Stary:1 http://deb.debian.org/debian bookworm InRelease Stary:2 http://security.debian.org bookworm-security InRelease Stary:3 https://download.docker.com/linux/debian bookworm InRelease Stary:4 http://deb.debian.org/debian bookworm-updates InRelease Stary:5 http://deb.debian.org/debian bookworm-backports InRelease Stary:6 http…

Good day friends, For some time now I've been trying a DAC (dac-pcm5102mk-i2s) with the Orangepi Pc Plus OS "Debian Stretch with Armbian Linux 4.19.62-sunxi" to put into operation. Unfortunately without success so far. On another Orangepi Pc Plus with Ubuntu Xenial with Armbian Linux 3.4.113-sun8i I activated the DAC after the tutorial I2S on Orange Pi H3 Da Alchemist February 29, 2016. It works fine there. Debin strech does not have a script.bin that I could convert in order to be able to make the settings. I would be happy if someone could help me. Best regards Hans-Jürgen Grigoleit

Upgraded kernel on existing working project and g_ether no longer working. So did fresh install on formatted card of Armbian_5.75_Orangepizeroplus2-h5_Ubuntu_bionic_next_4.19.20 If I do modprobe g_ether and then dmesg, I get the following udc-core: couldn't find an available UDC - added [g_ether] to list of pending drivers Is there something new in 4.19.20 that I must do? It used to work in older releases from 9 months ago or so...

Hi, I seem to have "fried" the default Debug TTL UART (the 3 pins next to the hdmi connector). (connecting the ground of the usb-ttl to TX of the UART and leaving it there for a few minutes is not a good idea it seems :-)). The orangepipc+ still works when booting from emmc (armbian 5.17 debian jessie, kernel 4.7.3) but does not seem to want to boot from microsd (tried console only 5.17/4.7.3, 5.21/4.8.1). So I would like to debug that but whatever usb-ttl I connect I don't see anything (tried 3 different usb-ttl to make sure it was not the usb-ttl device)> My question: is it possible to see uboot messages (or at least the kernel boot) via a different port…

Hello all, Where can I find the latest (and greatest?) version or Armbian. I think it is at the moment v5.24 . I looked at http://www.armbian.com/download/ and http://image.armbian.com/ . But no luck...? Is there another location? Or do I need to build from source? Thanks!

Hello, how to enable analog tvout? I have OpiPC board with legacy jessie desktop armbian image. I added module tv in /etc/modules. I change script.bin with: [disp_init] disp_init_enable = 1 disp_mode = 1 screen0_output_type = 3 screen0_output_mode = 10 screen1_output_type = 2 screen1_output_mode = 11 fb0_format = 0 fb0_width = 0 fb0_height = 0 fb1_format = 0 fb1_width = 0 fb1_height = 0 [tv_para] tv_used = 1 tv_dac_used = 1 tv_dac_src0 = 0 But there is no signal at all... I checked tvout with loboris ubuntu image (added "tv" to /etc/modules and fixed script.bin) and my tvout worked well. I noticed that when ubuntu image is loading tvout already gives to…

Hi, With current cubieboard2 image on SD class 10, local@solo:~$ time sudo dd if=/tmp/Armbian_5.25_Cubieboard2_Debian_jessie_next_4.9.7.img of=/dev/sdb bs=4k 326656+0 enregistrements lus 326656+0 enregistrements écrits 1337982976 octets (1,3 GB) copiés, 317,544 s, 4,2 MB/s not possible to boot on cubieboard2. Please find following log => => U-Boot SPL 2017.01-armbian (Feb 02 2017 - 02:16:44) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2017.01-armbian (Feb 02 2017 - 02:16:44 +0100) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: Cubietech Cubieboar…

Hello, currently I am working on my Orange pi one system (Armbian Linux orangepione 3.4.113-sun8i #10 SMP PREEMPT Thu Feb 23 19:55:00 CET 2017 armv7l armv7l armv7l GNU/Linux) to get my ILI9341-TFT display to work using the fb_ili9341 kernel module. I have read a lot of documentation and the display works (using the fb_ili9341 module) attached to my cubeitruck (also running armbian). I think that the problem is the GPIO- kernel module of the Orange PI one. These are the output messages in the syslog file after "modprobe gpio-sunxi": [ 343.417378] gpio_pin_1(7) gpio_request [ 343.417817] gpio_pin_2(8) gpio_request [ 343.4…

Hi All. May be I miss something but I do some searching and still can't understand. Problem configuration: Orange Pi PC v 1.2 (try 3 different) fresh loaded Armbian_5.90_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop.img (try different SD cards) any (try 3 different HP 2824, Zyxel Kinect, Cisco SRW2016) If I plug my Orange Pi PC with this image to 1Gb port I'v got blinking of lights and dmesg: [ 818.090335] PHY: gmac0-0:00 - Link is Down [ 819.090497] PHY: gmac0-0:00 - Link is Up - 100/Full [ 821.090494] PHY: gmac0-0:00 - Link is Down [ 822.090314] PHY: gmac0-0:00 - Link is Up - 100/Full [ 824.090335] P…

Good day all. Anyone having issues of not able to see anything after "Uncompressing Linux... done, booting the kernel." via serial console on Lamobo R1 ? Tried to experiment a bit, it seems that U-Boot works correctly, but in Linux kernel, sent data from USB-serial to ttyS0 arriving correctly, but anything written to ttyS0 is not visible on connected USB-serial adapter.

USB-touchscreen doesn't work with Cubietruck 3.4.113. The touchscreen well works with versions 4.9.xxx, but doesn't work with 3.4.xxx. I connected the monitor 1920*1080 and a touchscreen to Cubietruck. Cubietruck smartly works in video browse mode, but the mouse and the keypad aren't always convenient for control. Especially at night, too loud clicks. I pasted a touchscreen on the monitor. It works with versions 4.xxx, but video doesn't work. And with versions 3.xxx on the contrary. What I should make that the touchscreen worked with version 3.4.113?

Hi, I've tried to use the Ubuntu Xenial Mainline 4.9.4 server on my orange pi one. The u-boot log messages appear on the HDMI monitor but after the "Starting Kernel" message, the monitor shows "No Signal". I can still acess it through SSH. Executing dmesg, there is a log "simple-framebuffer: probe of 59f42000.framebuffer failed with error -12". I'm new to Linux, Is there a way I can fix it ? Thx.

Hi, I know it's a waste of time to play with an old bananapi pro but I think I could do it so I want to do it ! I can't make working PCM5102a DAC. I read a lot of things through different website but noway ! I tried https://forum.armbian.com/topic/9009-info-friendlyarm-pcm5102a-hat-with-nanopi-neo-under-mainline-4xx/ . I've only obtain this next to the step "armbian-add-overlay ./sun8i-h3-I2S-out.dts": $lsmod|grep i2s sun4i_i2s 20480 0 snd_soc_core 114688 2 sun4i_codec,sun4i_i2s snd_pcm 69632 4 sun4i_codec,sun4i_i2s,snd_pcm_dmaengine,snd_soc_core I tried the next step but nothing more: dmesg|grep -i pcm kee…

I'm trying to make a master image to install to some NanoPI Neo boards. I have everything running fine from micro SD card. I used armbian-config to flash from SD to the eMMC and it boot and works. Now I'm looking for a way to flash the eMMC from command line in an automatic fashion, after looking for other threads in the forum I found about command nand-sata-install but it has a GUI and no --help parameter, so I guess it is not the exact program I have to use. I tested using dd command to copy the disk, but since there is this u-boot thing I think it is not just a standard disk copy because it failed (maybe my problem). My final idea is to have a master SD …

Last night I was digging through the logs, and i found an error msg that said that I was over clocking the board without without heat protection. Couple of Questions: 1 I don't have a heat sink on the CPU, do I need one? 2 I haven't done anything to the CPU speed, and running Wheezy and Jessie off of different SD's. Is overclocking turned on in the release? It is really cold here in the high Desert, right around freezing for 4 to 12 hours every night. Not as cold as northern EU, but cold. The room temp is probably 60-65 degrees F. I have the Micro in the Micro case from Olimex. Does the processor need a heat sink? thanks in advance Mike

Hello. For some reason, UART1 does not work for transmission, only for reception. The transmitter pin itself is definitely working, I checked by switching this pin to output mode, and then switching it to a high/low logical level, everything works properly, the level on the Pin changes. How I check the UART itself: I installed picocom, shorted the TX and RX pins, and I’m trying to see what I’m sending. For UART2 this method works as it should, but UART1 only works for reception. I realized this when I opened the TX and RX, and was able to receive incoming data sent through the USB-UART converter.

Image Armbian_23.5.2_Nanopiduo2_bookworm_current_6.1.30.img uname -a Linux nanopiduo2 6.1.30-sunxi #1 SMP Wed May 24 16:32:53 UTC 2023 armv7l GNU/Linux It turns out the dtb has some missing pieces: ethernet@1c30000 { compatible = "allwinner,sun8i-h3-emac"; syscon = <0x1e>; reg = <0x1c30000 0x10000>; interrupts = <0x00 0x52 0x04>; interrupt-names = "macirq"; resets = <0x03 0x0c>; reset-names = "stmmaceth"; clocks …

Hardware setup :: Olimex Lime 2 Rev.k + 7" LCD + 5V power supply through the power jack. No battery is connected to the lime 2 board. Problem :: when the board boots up, the xfce power manager shows that the Battery is connected and it's in charging mode. The current charge value of the battery changes randomly like 92%, 56% and etc. When it reaches 0% the board will shut down. It completes the shut down procedure. The following is the terminal output, to find the battery status. Even though the battery is not connected you can observe that it returns the Voltage and reports that the battery is present root@olinuxino:~# cat /sys/class/power_sup…

Hi, First i'm french, so please excuse my english. I'm new to this forum but not new with Orange Pi (One) I'm already running 4 OPi with some basic hardware (like DS18B20, HT21D, relay module, etc...) for different projects like egg incubator, central heating, chicken door, etc... I'm working on a new project for a connected beehive and i'm trying to use loadcells with an HX711 but i can't get any data from my HX711. The code i'm using is this one: https://github.com/ggurov/hx711/blob/master/hx711.c The only thing i can obtain is "No data to consider" I have made a "quick and dirty" script to change #define CLOCK_PIN and #define DATA_PIN fro…

I now connected a ssd drive to my cubietruck. with ls /dev/ | grep sd I got sda, but when I try to format this drive with mkfs.ext4 /dev/sda1 I get this errormessage: Could not stat /dev/sda1 --- No such file or directory The device apparently does not exist; did you specify it correctly? How can I format the ssd ?

hello Igor, I get some error information after updating the new kernel v4.1 root@cubie:~/3.4.108# dpkg -i linux-image*.deb (Reading database ... 70156 files and directories currently installed.) Unpacking linux-image-cubietruck (from linux-image-cubietruck_4.1_armhf.deb) ... dpkg: error processing linux-image-cubietruck_4.1_armhf.deb (--install): trying to overwrite '/lib/modules/3.4.108-cubietruck/modules.builtin.bin', which is also in package linux-image-3.4.108-cubietruck 4.0 dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: linux-image-cubietruck_4.1_armhf.deb how to solve this. Best regards Fla…

Hi, I am running Debian buster 10.1 with following kernel on nanopir1 (1Gb of RAM) Linux srv-nanopir1-170 5.3.9-sunxi #5.99.191113 SMP Wed Nov 13 08:12:49 CET 2019 armv7l GNU/Linux I have all services up on local LAN Ethernet port, but not possible for me to setup WAN Ethernet port . Packages installed are .... The boot sequence is ... My current network configuration in udev is .... As a result, r8152 kernel module is correctly installed After connected one RJ45 to external DHCP server (running) , it is not possible to setup interface …

I'm trying to setup a GPS-based time server on an Orange PI Zero 3, running Armbian 24.8.0-trunk.495, kernel 6.6.43-current-sunxi64. I have the exact same hardware setup working fine on a RaspberryPI 4b, running RPI OS / Debian 11 (bullseye) , kernel 6.1.21-v8+ #1642. On the RPI4, gpsd recognises the (cheap chinese "M8N") GPS module as u-blox and keeps working in a stable way root@rpi4:~# gpsctl /dev/ttyS0 /dev/ttyS0 identified as a u-blox SW ROM CORE 3.01 (107888),HW 00080000 at 9600 baud. the /boot/config.txt has these two lines for the UART config enable_uart=1 init_uart_baud=9600 On the OPIZ3 I configured /boot/armbianEnv.txt for UART5…

I am trying to use an Iono Pi Board from SFERA Labs on an OrangePI PC Plus. https://www.sferalabs.cc/product/iono-pi-board/ I was able to get i2C working so that I could connect to some devices like a temp sensor and accelerometer. My issue is pretty basic at this point. I am simply trying to blink the green light on the board. According to docs, the onboard LED is connected to GPIO7. So through looking at documentation I was able to decipher that GPIO7 is physical pin 7 on an RPi. I am using pyA20.gpio. Accordingly Pin 7 = PA6. However when I set PA6 high the light does not come on. Am I missing something? Anyone have expe…

Dear all, I am using armbian Mainline Debian Jessie 4.9.7 and 4.9.12 on a Banana Pi Pro (A20). Coming from legacy and fex, I came a long way learning a lot about Device Trees, Overlays, etc. the last 2 weeks. I even compiled some dev kernels to experiment. I currently struggle with with the OTG port. I have two devices on the primary slots and need to get the OTG in host mode to attach my third device. I've read that the OTG is not providing 5V to the device. Therefore, I use Pin4 5V DC and Pin6 GND of the 40Pin header. It works well when connecting Device #3 on USB 1 or 2. But not on OTG. I used dmesg to track devices. Is there an…

Hi, without consulting the specs first I bought a 128GByte card and obviously it doesn't work on my OPi Plus2e Is there any chance this will be fixed in software or is this a hardware limitation? Cheers, pansen

Hello I was build image for my orange pi pc2 devices: BOARD=orangepipc2 BOARD_NAME="Orange Pi PC2" BOARDFAMILY=sun50iw2 VERSION=5.46 LINUXFAMILY=sunxi64 BRANCH=next ARCH=arm64 IMAGE_TYPE=custom BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image I was faced with strange thing: After burning another image and lunch it on the device - on the first (and every) boot I see "first start panel window". And when I do formatting this SD card, and burning again - everything alright (first start panel window dose not appear) I have been already burn 10 SD cards with same image and met th…

I'm trying to make a master image to install to some NanoPI Neo boards. I have everything running fine from micro SD card. I used armbian-config to flash from SD to the eMMC and it boot and works. Now I'm looking for a way to flash the eMMC from command line in an automatic fashion, after looking for other threads in the forum I found about command nand-sata-install but it has a GUI and no --help parameter, so I guess it is not the exact program I have to use. I tested using dd command to copy the disk, but since there is this u-boot thing I think it is not just a standard disk copy because it failed (maybe my problem). My final idea is to have a master SD …

Hi, After upgrading from Lemaker Lubuntu with 3.4 kernel to the latest Armbian with 4.9 kernel my application that reads INPUT PIN using wiringPi is behaving very strange and unstable. I simply make a pin INPUT and check the value using gpio read command. When I short the pin the value returned by gpio command changes not always immediately. Some times it takes up to 5 seconds to refresh the value. I mean, it keeps returning me "0" while the pin is shortened and only few seconds later it starts returning me "1". WiringPi is installed from this repo: https://github.com/LeMaker/WiringBP Is it still fully compatible with 4.9 kernel? Or do I need …

Hello everyone, I have a10 board and i'm trying to plug 7' LCD wich touchscreen (http://www.waveshare.com/wiki/7inch_HDMI_LCD_(B)). Chinese manufactorer changed usb pid/vid, and in fact this touchscreen is eGalaxTouch. And when i'm trying to build driver - it requires uinput module, which is missing. Is it possible somehow to get it? On my desktop debian /dev/uinput is preseted by default. Sorry for my bad english. Regards.

where can i find de virtual Linux usb server for my orange pi pc and armbian 5.2? i download jessie desktop regards Tex

Hi there, i need some help with using the UART1 pins 8 & 9. I own a Duo with Ubuntu 16.04.6 I've installed a software that is able to send codes over the UART1 pins to my smart home system. The software is 'active (running)' but has no connection via UART1. UART1 is enabled(npi-config) but i does not work. WiringNP is required for my software and installed. Is there any point i've missed? Did i have to switch UART1 pins to in- and output? One error i get: Service Control Manager on computer xx.x.x.xx cannot be opened. You may not have permission to do this. PS: These pins must work, i rebuild an…

Hi, Recently while I was using the banana pro, it locked itself up and I had to manually pull out the power. And after that, it cannot boot anymore with armbian or bananian, the red light turned on and thats it, no more activities. :-( But with lemaker's oficial image it can boot up normally. What could be the problem? Do I have a faulty hardware? Thanks!

Hello, my Orange Pi Zero CPU is constantlyrunning at 67-68-70°C (it is the same with/without passive cooler). Is this temperature ok for my board? Can I run it with this temperature long time (weeks, months, years)? Thanks for help.

Hi, trying to start my Banana Pi Pro Board with the latest Armbian buster image (Armbian_21.02.1_Bananapipro_buster_current_5.10.12.img.xz) without success. There is initial output on the screen until there is the message "Starting kernel ...", the after a few seconds the monitor loses its signal and nothing seems to happen any more see: https://c.1und1.de/@520257322610590089/1IBkHiwHQX6jYxLPdlkTZQ Reading through the forum I guessed it could have to do with an issue of automatic discovery of the correct DTB, so I edited the armbianEnv.txt file and added the following line to it: fdtfile=sun7i-a20-bananapro.dtb But still the sam…

Hi to All, I recently upgraded my "test server" to the current version, by flashing a new image to my sd-card. However i forgot to recover some essential files, before flashing! I liked very much the login info about the the number of available updates, since I used the testing repo at that time. Could someone provide the code snipplet for that piece of info ann thell me, in which file to place it?? Well, many many thanks for your help and advice! regards, ireng

Hello! Is there any hope to acquire a r3p2 or a newer Mali driver support in an armbian kernel for Banana Pi?

I've got a LeMaker Banana Pi Pro board, with LeMaker Banana Pi Pro Camera V1.0 which is a ov5640 module. I think there are some on-line manuals from official LeMaker, for instance: http://wiki.lemaker.org/BananaPro/Pi:Camera_Module . However, it seems Armbian_5.59_Bananapipro_Ubuntu_bionic_next_4.14.65 hasn't provided such a ov5640 driver module for me to load? Where can I find the ov5640 driver module ? Cheers Pei

Is there a way to check for a new kernel without downloading it?

Hello. please tell me, I can find somewhere kernel modules for Armbian legacy trusty? interested ntfs and ufs modules. or teach how to build their own on my device. Wbr, Dmitry.

Hello, actually it was not the first time the upgrade failed on this board: - upgrade 5.11 to 5.15 -> returned successfull - reboot - at boot system can not find file: sun6i-a31s-bananapi-m2.dtb (file sun6i-a31s-sinovoip-bpi-m2.dtb for BPi M2 is available) - fixed it by linking to the existing device tree blob sun6i-a31s-sinovoip-bpi-m2.dtb - reboot again - no network (my /etc/network/interfaces has been set to armbian default, same as /etc/network/interfaces.default, this happened the first time) fixed it again by setting the correct content I don't know if the upgrade process is the problem or if there is something messed up on my board... Now ev…

Hello, Is it possible to install serviio (armbian) ? Board: Orange pi One OS: Armbian - Ubuntu xenial 16.04

Hi! Anyone use display? GND: Shared VCC: Power supply SDA: Bus Information SCL: clock data bus From site: https://github.com/vvromanov/cb_i2c_lcd https://github.com/vvromanov/cb_i2c_lcd/blob/master/i2c_lcd.c#L28 But how to right connect display?

Hi all. I install Ubuntu_xenial_default with kernel 3.4.113 and want record video from CAM500B with ov5640 image sensor. I had edited camera section in fex file with next options: [csi0] vip_used = 1 vip_mode = 0 vip_dev_qty = 1 vip_define_sensor_list = 0 vip_csi_pck = port:PE00<2><default><default><default> vip_csi_mck = port:PE01<2><default><default><default> vip_csi_hsync = port:PE02<2><default><default><default> vip_csi_vsync = port:PE03<2><default><default><d…

Hi there, I have 2 OPi PC+, one was with Jessie, then upgraded to Stretch, Working almost fine, only one issue was "systemctl start postgresql.service" not working. I used a workaround, "su - postgres -c 'pg_ctl start'". Postgres not from repo (previously was from repo) but compiled from source, as I need at least version 10 for "logical replication". Not at some point of time, I noticed message, that kernel package is to upgrade (3.4.112 to 3.4.113). After reboot graphics don't start. "No screens found". Ok, so I tried to upgrade (apt update, apt upgrade, apt dist-upgrade after changing name in /etc/apt/ files). Now it's almost crash: - graphics …

i have just downloaded the new version (dated 5-8) for jessie 4.1.4 for the cubietruck. it runs till it gets the greetings screen but then hangs and says: time timed out waiting for device dev-ttyS).device. depend dependency failed for serial getty on ttySO. -- i had a hdmi monitor, but then connectted a vga monitor (both show the initial informations) - the same result. what did i wrong? andrew ps. thank you for adding the upgrade using ppa!

Howdy, I set up a new OrangePi Zero with the Legacy 3.4.113 Ubuntu Xenial. I was able to get wifi working however when I try to do a sudo-apt get update or upgrade it freezes and crashes. I am using a 32gb Samsung Evo. Cpu temp is hovering around 57 C with no load. Any tips besides reinstalling the image?

I usually build a new armbian full os image, apply some kernel options and have no problems booting a sopine64. The last known good version for me was: Armbian 5.51 / Kernel 4.14.54 The latest (and starting with 5.57) with Kernel 4.17.16 only seem to 'half boot' - they start up uboot but fail to load the OS and instead attempt to do a network boot over TFTP. The errors go by so fast that I can't really read it and have to resort to trying to video capture it and the monitor seems to be slow to initialize and i only see the tail end of the errors scroll by. I am sure a lot changed between 5.51 and 5.57 - I noticed a new…

Hi, i got a Pinebook and install the latest Armbian Image. All is working fine, only the sound output make problems. It isn't matter if i play a mp3 file or a play a YT Video. The sound is just strechted, drawned, like in slow motion. What can i do to solve this issue? Any ideas? Thank you for your help.

Hi, When I put a heavy load on my NanoPi NEO2, it locks up. The ethernet light keeps flashing, so there is still something alive? After a power reset, the NEO2 works again. I've already put a CPU fan on my CPU. CPU temp is at 25 degrees Celsius in rest, and goes up to 37 degrees Celsius under the heavy load. The heavy load is a "make -j4" of a C source code project Tips how to solve this? sander@nanopineo2:~$ while true; do date ; uptime ; cat /etc/armbianmonitor/datasources/soctemp; sleep 2; done | tee mijn-log.txt Tue Aug 22 11:46:37 UTC 2017 11:46:37 up 5:24, 2 users, load average: 0.00, 0.00, 0.00 28342 …

Hi, I tried to switch on some LED during boot with script.bin. (connected to PH11). Decompiled script.bin, changed several times PH11 to be an output with value 1 (pin 15 on GPIO3). It works if I switch it on from Linux. ; Was the first I changed lcd_used=0 lcdd11 = port:PH11<1><1><default><1> ; Whats this? Not used, or? ms_used = 0 ms_d3 = port:PH11<5><default><default><default> ; Both changed gpio_pin_19 = port:PH11<1><1><default><1> pin_19 = port:PH11<1><1><default><1> Compiled it again, copied it into /boot/script.bin, rebooted, nothing. Its the las…

Hello, Do you guys have some tips on reducing power consumption to an absolute minimum? I've made some progress and reduced it to about 500mW on idle. with some CPUs shut off. I would like to get it lower for battery saving. I'm currently building a custom image with as much of the functions I don't need (SPI, i2c, bluetooth etc) turned off hoping that I will get some more power savings. Not sure if this will make a difference yet. Ideas would be appreciated!

Hello, I'm trying to make MB1242 sonar working with my nanopi but every time I run i2cdetect, I got "i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0". Sonar works fine on RPI after changing i2c_baudrate to 50000. Is there any way to do the same at nanopi?

I have tried to use the nand-sata-install to allow me to boot the roots from an external USB HDD. It goes through the process but after rebooting, the "loading kernel" message appears and then nothing - I have tried this a few times and even used the latest version of the script on GitHub. Any ideas on how to make this work - I have a external USB HDD (500mB).

My Opi3 has been running armbian for over 2 years (edge kernels & usually fully up-to-date). I have been using eMMC & I noticed an apparent slowdown about 6 months ago. As it performs cron-based tasks and is a stats collector, this performance was not noticable but doing a manual BIG dist-upgrade, it seems to take forever (20 minutes to do what should be under 5 minutes). If I run "mmc extcsd read /dev/mmcblk1", the results tell me that the eMMC is at least 90% used whatever that really means. Is this a sign of imminent failure ? hdparm shows read results of 17 MB/s which is actually slower than my alternative SD card boot device and nearly 1/10th …

Hi, System: A20Lime2-4gb with latest legacy image Linux lime2 3.4.113-sun7i #23 SMP PREEMPT Wed Jun 14 23:57:45 CEST 2017 armv7l armv7i armv7l GNU/Linux When I shutdown or restart, it throws me back to login screen and again loads desktop even if I don't enter id and password and then shutdown automatically within 10 secs . I want it to shutdown/restart without this login screen. I tried shutdown from terminal ' sudo shutdown -h now' , 'sudo poweroff' still giving login screen. How can solve this issue ? Thank you in advance

Hello! I am working on a project that requires coss platform development. Optimally I wish to connect the B-Pro directly to my computer in order to access it from there. Is there any work on this available? I know the BeagleBone can do it for example, bt haven't found anything related to the Pro. Any Information would be inmensely useful and appreciated. Added to this, I want to know if any of you have had any experience with QT for the BPro as well. Thank you!

Hi, as I had set up my CubieTruck I decided to go with Legacy Wheezy ... Now I think about become a bit more current :-) Option 1 is to Upgrade to Legacy Jessie ... This is described in the documentation and hopefully should work that way, Correkt? Or Option 2 would be to go to Vanilla Jessie. Is this possible too? How? Thank you for your support, Ingo

i have Downloaded the Image for the Orange PI PC H3. the Image flashed over the MAC with DD are only this screen. Then i think ok i testing windows have testet win 10 with Rufus and win 7 with Suse flasher with is in the Package. Are all the same. how its the Problem?

Armbian_5.59_Nanopineo2_Ubuntu_bionic_next_4.14.65.img does not see the sound codec at all. The status matrix here: http://linux-sunxi.org/Linux_mainlining_effort#Status_Matrix tells that Audio Codec should be supported since kernel 4.12 on H3 (H2+ is the same, as far as I know). But Armbian does not see the audio codec nor on NanoPi Neo2 (H5), nor even on on NanoPi Duo (H2+), although all the img files I used have 4.14 in their name. However, even with FriendlyElec's own image nanopi-neo2_ubuntu-oled_4.14.52_20180628.img there is a different issue - the sound is mono instead of stereo! I tried speaker-test: speaker-test -…

I have this FriendlyArm ZeroPI with one micro-usb (power only) and one usb 2.0 A connection, yet dmesg yields 4x 2.0 root hubs and 4x 1.0 root hubs. Can anyone enlighten me? odd. old version is uploaded. new version; http://ix.io/2mj7

Imagewriter does not work in Win7 does not see drives. I have a Orange Pi One and using the link on this site I have downloaded Armbian. However although Suse imagewriter starts it does not see any drives to write to on my laptop and not the sdcard either. I can select Armbian but clicking copy just brings up a error. I downloaded Rufus but all that will do is format the sdcard. There is a raw file and a asc file for Armbian how do I create a sdcard to boot my Orange Pi One? using windows 7.

Hello I need to connect my modem Huawei E3372-325 to my NanoPI but when i write command ls usb get it root@PC_42:~# lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 3566:2001 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub…

considering to buy orange pi 3 with new H6 cpu, usb3.0 port and onboard emmc, but everyone has been complaining official images, just wondering if orange pi 3 will be supported soon.

[BANANA PI PRO - SO running on SD] So, on every system upgrade I do, I end up with something broken. Normally it won't boot because of some kernel misconfiguration or due the encrypted HDD that I use connected to it. On the last upgrade the same occurred. However, normally, I can solve stuff by myself. This time I couldn't fix everything (yet). I think that the only solution would be me compiling the kernel myself. First the system wouldn't boot. After a few kernel replacements, I could make it boot, kind of. If I have my encrypted LUKS HDD connected to it, it will boot to some degree and hang in there forever. If I take it …

I'd like to use Orange Pi PC as a HID keyboard USB gadget/USB device. There is a tutorial on link here but it makes Orange Pi into a serial device. I want a HID device (keyboard).

Hi, I was on the legacy kernel until recently with my bananaPi M1. I switched to the vanilla kernel but since then, when I try to use the GPIO python library (for bananapi from LeMaker github), it works quite well except for functions gpio.add_event_detect() or GPIO.wait_for_edge(channel, GPIO.RISING) This usually disconnect my network and the event is never detected. I have to reboot the PI to restore the state. Also, a normal read/write state GPIO.input(PIN_NUM) works perfectly... I assume it is due to the vanilla kernel but could not find any documentation on why this is happening... Any answer/comments would be much appreciated! Let me know if yo…

Hardware: Banana Pi Pro. The Android is based on Linux. Android very well plays Internet video HTML5. Therefore hardware resources allow to play Internet video HTML5. Bananian and Armbian doesn't play Internet video HTML5. Please help! How to play Internet video HTML5 on Bananian or Armbian? Someone did it? What results?

Hello, I have a Orange Pi One Plus. It has an onboard mic. No matter what i do i cannot record sound from it. Please help, how can i record sound from onboard microphone? marko@orangepioneplus:~$ cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=orangepioneplus BOARD_NAME="Orange Pi One+" BOARDFAMILY=sun50iw6 BUILD_REPOSITORY_URL=https://github.com/armbian/build BUILD_REPOSITORY_COMMIT=d485420c00 VERSION=22.08.1 LINUXFAMILY=sunxi64 ARCH=arm64 IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=stable marko@orangepioneplus:~$ uname -a Linux orangepioneplus 5.15.63-sunxi64 #22.08.1 SMP Tue Aug 30 07:11:56 UTC 2022 aarch64 …