Allwinner sunxi

Hi. I encountered problem, glimpsed through topics and didn't found anything similar so I am posting this one now. Had set up OrangePi Zero 256MB version with Domoticz and everything looked great. I have 2 internet connections, one is PON FTTH and the other one is VDSL. So I have 2 routers with RJ45 and 2 WiFi networks at home. One for my personal usage (ftth, locked router by ISP, static IP but no port forwarding) and the other one is for all home users (dynamic IP but full access to router options). I hooked up OPI using cat5e cable to my router and this connection is working perfectly reliable. I had XR819 hooked up to VDSL router as auxiliary connection (and con…

Hi, I tried two builds for my OPI Zero. Armbian_5.35_Orangepizero_Debian_jessie_next_4.13.16.7z Wifi works but no audio. (and instabel ethernet connect) Armbian_5.35_Orangepione_Ubuntu_xenial_default_3.4.113.7z Audio works but no WiFi In witch build works both ?

Hi. I've upgraded Buinic to Eoan and encountered an error with apt-get. Decided to have a fresh install of Disco from https://dl.armbian.com/orangepizero/ and got exact same error. I did nothing with the installation except that I've configured WiFi with ntmui-connect command. So I guess this is some issue with Ubuntu releases 19.xx root@orangepizero:~# apt-get update && apt-get upgrade Hit:1 http://ports.ubuntu.com disco InRelease Hit:2 http://ports.ubuntu.com disco-security InRelease Hit:3 http://ports.ubuntu.com disco-updates InRelease Hit:5 http://ports.ubuntu.com disco-backports InRelease Hit:4 https://apt.armbian.com disco InRelease Traceb…

First of all, hello to everyone. I'm new to this forum so sorry if my question may look stupid, but i've strolled through the internet far and wide. I cannot find simple(for dummies version) step by step tutorial how to connect TFT waveshare knock-off with XPT2046 controller. Compatible with ADS7846 according to this thread: https://www.raspberrypi.org/forums/viewtopic.php?t=143581 I was able, using info from link below to run command line on legacy kernel. https://kaspars.net/blog/linux/spi-display-orange-pi-zero So i know about reverse SPI connection in orange pi zero. When i tried command: sudo modprobe fbtft_dev…

Hi All! OS - ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi OPI Zero. armbianEnv.txt : overlay_prefix=sun8i-h3 overlays=uart2 param_uart2_rtscts=1 RTS CTS don't work I check the work of the logical analyzer. The line RTS does not change the voltage during the request for data transmission. This is necessary for me to connect the MAX485 chip to UART2 OPI Zero.

I would like to remove "everything" from the installation, which I don’t need, with the goal to minimize the footprint. I installed tasksel and its show a lot of packages on disk... so my question is what can be removed to keep a basic ubuntu server without a desktop interface and with some most used functions and files. I tried to remove some of them, like… ubuntustudio-videoubuntustudio-photography ubuntustudio-graphics mail-server ubuntu-gnome-desktop ... I can imagine to remove all CD installation and images as well... …but my problem is that if I for example remove “ubuntu-gnome-desktopâ€, the OPI Zero is not answering on ssh request any more. So, for me…

Hi, I'm running Armbian 5.38 with kernel 3.4.113-sun8i on an Orange Pi Zero. I'm writing an audio streaming application using the portaudio library for accessing the soundcard. It seems that the OPI Zero samplerate for the built-in microphone is configured at 24kHz instead of 48kHz. $ cat /proc/asound/card0/pcm0c/sub0/hw_params access: MMAP_INTERLEAVED format: S16_LE subformat: STD channels: 1 rate: 24000 (24000/1) period_size: 960 buffer_size: 1920 If I connect an external USB soundcard, I get the expected values: $ cat /proc/asound/card2/pcm0c/sub0/hw_params access: RW_INTERLEAVED format: S16_LE subformat: STD chan…

On a fresh install of Armbian 20.08.1/Linux 5.8.5-sunxi on an OPi Zero (256MB version), total memory is 238MB according to "free -m": root@orangepizero:~# free -m total used free shared buff/cache available Mem: 238 74 78 1 85 154 Swap: 119 0 119 238MB is not 256MB. :-) I assume the discrepancy is due to reserved framebuffer memory, but after a bit of testing I've found that the "sunxi_fb_mem_reserve" parameter (set to "16" in /boot/boot.cmd by default) has no apparent effect. Here's a boot with the Armbian default "sunxi_fb_m…

Hi, Using the latest Armbian release (19.11.3) on OPi Zero (512MB, board revision 1.5) I have a strange issue. On kernel 5.3.x, Ethernet connectivity drops sporadically, around once every couple of minutes, for typically 10 seconds or so and then recovers. When the drop happens, a ping from another machine on the network produces 'no route to host' - then after around 10 seconds or so the network comes back up. The OPi Zero continues running normally during the 'outage', without functional network access. There is nothing in the dmesg log when this happens. Switching to kernel 4.19.62 from armbian-config, everything works perfectly. Back to 5.3.x, the iss…

Is it possible that there have been some image changes that broke the XR819 wifi completely? The available images for download on the Armbian page (5.3 server, and 5.4 minimal) as well as a custom built "legacy" branch linux-4.19 image all show the same behavior, The wlan0 interface is not active and it's not possible to bring it up. And dmesg shows that module has been initialized but not much more. Armbianmonitor support info: 5.3.9 official buster server image: http://ix.io/240Y 4.19.88 self-built, two days ago, legacy branch: http://ix.io/240U Everything below is from the official image, but the 4.19 image shows the exact same It is definitely not a h…

ARMBIAN 5.75 stable Ubuntu 18.04.2 LTS 4.19.38-sunxi Orange Pi Zero Board Please refer armbianmonitor.log for armbianmonitor -U command output details I have configured My Orange Pi Zero onboard wlan chip (xradio_wlan driver) to work on both Ap mode and Client modes simultaneously. When both Ap and Client interfaces are up and working, and when the connected wifi channel of the Client interface changes, kernel hang occurs. Error message [20148.872296] rcu: INFO: rcu_sched self-detected stall on CPU [20148.877893] rcu: 1-....: (4945709 ticks this GP) idle=8aa/1/0x40000002 softirq=9640/9640 fqs=2447771 [20148.887182] rcu: (…

Hi. I'm running Armbian Distro Debian 12 Minimal/IOT with Gnome GUI on an Orange Pi Zero3 2gb and 4gb models. I installed XRDP Xorg to be able to access from Windows 10. I can access the systems remotely, but both machines turn off after a short period of activity, somewhere between 5-10 minutes, whether they're idle or performing some activity. I've already looked for some hibernation/suspend option, but I only found something related to turning off the screen, which didn't solve the problem after being disabled. The Orange Pi Zero3 2gb machine ran for a few months using another version of Armbian recommended by the manufacturer's website without this…

Hello, board: Orange pi One OS: Armbian 16.04 I installed the opi monitor using the command: sudo armbianmonitor -r error: Memory usage is not displayed, show only: Used: NaNkB (NaN%) Available: NaNkB Total: NaNkB The free memory is displayed in the statistics, but not in the Status. I try: edit file /etc/rpimonitor/template/memory.conf Locate line reading dynamic.15.source=/usr/bin/free -mk Replace this line and the following (in my version: lines 21 and 22) with dynamic.15.source=/proc/meminfo dynamic.15.regexp=MemAvailable:\s+(\d+) Save file and restart rpi-monitor . But still memory usage …

Hello, How can I play a video on the TV without a GUI/X11 installed? When I try mpv it says: mpv 05\ Oscillofun.mp4 [input/#1] Failed to read LIRC config file ~/.lircrc. Playing: 05 Oscillofun.mp4 [stream] Video (+) --vid=1 (*) (h264) [stream] Audio (+) --aid=1 --alang=und (*) (aac) File tags: major_brand: mp42 minor_version: 512 compatible_brands: isomiso2avc1mp41 creation_time: 2016-11-10 13:22:28 date: 2014-07-02T13:04:18+0200 encoder: HandBrake 0.10.5 2016021100 [vo/vdpau/x11] couldn't open the X11 display ()! Error opening/initializing the selected video_out (-vo) device. Video: no video AO: [alsa] 44100Hz stereo 2ch float A: 00:00:01 / 00:02:31 (1%) E…

Hi, my problem is that I can't figure out why doesn't wifi access point doesn't show up, after setting up neither with Config utility from the desktop, neither manually from the website documentations help. What am I missing here? First, the Config utility that I'm using it asks me to reboot every time I set it up successfully, but after reboot it doesn't appear anywhere, neither my smartphone won't find the ARMBIAN connection. Second, I tried the way it is documented on the websites help section on how to set up an access point. I've changed the required files with nano, copied and nothing. I haven't used wired internet con…

Orange Pi Lite - Armbian 5.14 The desktop shutdown (or shutdown -h now) shuts down the desktop, the system starts shutting down, then the desktop starts again, then disappears and the system shuts down. Its not a disastrous problem, but just annoying. I've traced it to the fact that 'nodm' is seeing the desktop stop, and then restarting it. Apparently either 'nodm' isn't getting the shutdown signal, or ignoring it, or getting it too late. Any guidance on what 'nodm' config, or some other config might help me to fix this? /K

Hello, I installed Armbian/(debian jessie) on my Orange Pi Plus (EMMC). Works good, but i can't find the temp of the processor. (lm-sensors don't work/can't detect sensors) What should i do?

Hello All, First of all excuse me if such topic exist. I am using the Desktop version with legacy kernel provided from Armbian - https://www.armbian.com/orange-pi-plus-2/ I have tried to fix my overscan issues on my SHARP LC-42ADE-BK from the Aquos series. I had zero luck in resolving the issue. I used the documentation available on the Sunxi-wiki for FEX configuration ( http://linux-sunxi.org/Fex_Guide ) scavanged the internet for all kinds of information for configuring the scale/overscan etc. with u-boot/fex and such. Unfortunatly my TV does not let me choose Aspect ratio or such fucntions when my Laptop or OPI device is pluged with HDMI…

Hello All, m new to this forum and new to armbian. Probably someone can help me. Im trying to get an 64GB flash drive working on a Opi+ 2E. Using the eMMC storage for boot and the flash drive as "the hard disk". nand-sata-install gives me the option to install this combo but at the end the system boots in an infinite loop telling me something is missing on the USB drive. Installing to boot / root eMMC works like a charm. I mounted the USB on another linux system and the drive looks good. ext4 and a root filesystem as expected. Am i missing something? How to get the eMMC boot, USB root option up and running? OS: Armbian 5.20 (jessie server), updated / up…

I am using an OPi+ 2e as an OMV box. Tonight I updated to 5.38 (4.14.15 kernel). After the update, the network connection drops between the router and the OPi at random intervals. At least once in a hour, sometimes within 10 minutes. Tried restarting the device and the router, to no avail.

Hello I have a Problem with my Orange Pi I've started a update on my running Orange Pi Plus 2 when i suddenly had a Power Loss on my house. After I fixted my Power Problems the OPi won't boot anymore All what i from the Debug Port get is following in repeat: Spoiler U-Boot SPL 2016.09 (Oct 15 2016 - 14:24:41) DRAM: 2048 MiB Trying to boot from MMC1 Or with another Image: Spoiler HELLO! BOOT0 is starting! boot0 version : 4.0.0 fel_flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rt…

opi+2e What is the best way to install a mainline kernel so that I can check out containers? I tried to install mainline kernel and ended up with a blank screen I then installed a nightly and it is just cli so I installed open box by ssh root@10.x.x.x9 apt-get install openbox obconf and now i get a blank screen also what is the best way to get a gui with mainline kernel? Thanks for your help Dave

Hello, Armbian shows me very low wifi coverage and fail to connect, with other distros the signal is good, any solution? I use Jessie Desktop 3.4.112 Sorry for my bad english Thnks

How can I disable or lock my opi + 2e's microphone with a password to prevent anyone from hearing thnks

Hi, do you remember my issue with 2 opi1? Well, today I burned again an armbian image with etcher and connect either of the two opi one, to a usb-ttl converter (an arduino). ok, when I put the power on the result is what you see in the attach... the two freeze on DRAM: always. the power is a xiaomi power adapter 5v2a (double checked with a multimeter) and a handmade cable (checked with the multimeter too, 4.8v/4,9v always) so...can I finally tell that my two board are faulty? or there is something I could do? thank you in advance

I do not use wifi at all, so I'd like to disable it completely. It's not configured right now, but I wonder if I could power down whole chip, ex. commenting it out in DT file? Does it save some power or not?

I'm using Armbian 23.02 Bullseye CLI. I didn't want the HDMI to show the boot system log and TTY1 login screen. According to the armbian documentation, I changed "console=both" to "console=serial" in /boot/armbianEnv.txt. I checked /boot/boot.cmd related to console, and I confirmed that this modification is OK, but it cannot start, uboot printed "Starting kernel..." After that, there is no output, and the power supply is only 5V 170mA. The following is the printing of the serial port. If anyone has been in a similar situation, please give me a little help, thank you very much. U-Boot SPL 2022.07-armbian (Feb 17 2023 - 22:32:08 +0000) DRAM: 2048 MiB Trying …

Hi there, I have an OPi3 box that acts as home surveillance server. It has WiFi configured as AP, client is Android phone with static IP/routing and IP Camera software. Problem is, that there is NO IP routing. I CAN access video / pictures from phone on OPi box, but NOT from my LAN. Below is routing table and iptables. Looks ok but not working. I am able to access (from LAN) WiFi IP of OPi. Also can access video served by "motion" software on OPi. But no direct connection to Android phone. root@orangepi3:/tmp# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 1…

Hi guys! I am making a separated network to connect my OPi3 to my old notebook to run some codes of my research. So, the problems is with ethernet connector in Orange Pi 3 that when I connect the cable from OPi3 to my switch LEDs just flash slow and in big intervals. When I try to ping from OPi3 to computer the ping just happens after big time later. I verify the cable and the switch with other devices (my personal notebook and my notebook from work). Everything is ok and running well. One thing blow my mind: when I connect cable from OPi3 directly to my notebook the LEDs of ethernet of OPi3 works normally but in the armbian the networks not alway…

I have move system to emmc, and want to use sdcard to storage videos from camera. So I want to sdcard can automount/umount after hotplug. I have try to use udev to fulfill it. But it seems not work. I add a rules for udev at /etc/udev/rules.d: ACTION=="add",KERNEL=="mmcblk2p1",RUN+="/etc/udev/sdcard_hotplug.sh add /home/opi/Videos/sdcard %k" ACTION=="remove",KERNEL=="mmcblk2p1",RUN+="/etc/udev/sdcard_hotplug.sh remove /home/opi/Videos/sdcard %k" And add a shell file at /etc/udev/sdcard_hotplug.sh #!/bin/bash case $1 in add) mkdir -p $2 mount -t exfat -o iocharset=utf8,rw,sync,umask=0000,dmask=0000,fmask=0000 /dev/$3 $2 ;; remove) umount $2 …

HI to all, excuse me but this is my first msg. I have a OPI3 board and I try different OS (Arabian, Ubuntu, Debian) all in different release but I do not have wifi and lan. for wifi I have already try with copy firmware file but is is the same for lan I have in dmesg eth0. UP and DOWN. In my experience I have found only Ubuntu Xenial 4.9.118 on the Orange.org web site with wifi OK. can you help me? Thanks

while updating my dev-OPiOne Welcome to Armbian bullseye with Linux 5.5.8-sunxi package bsp-kernel[20.05.0-trunk] u-boot[20.05.0-trunk] dtb [20.05.0-trunk] firmware [20.05.0-trunk] config[20.05.0-trunk] branch[dev] Linux opi-one 5.5.8-sunxi #trunk SMP Wed Mar 18 21:19:37 +03 2020 armv7l GNU/Linux via apt update I did get the follwing error-message: Trigger für mime-support (3.64) werden verarbeitet ... E: Schreibfehler - ~LZMAFILE (28: Auf dem Gerät ist kein Speicherplatz mehr verfügbar) I did found out via df that /dev/zram0 = /var/log is used up to 100% :( root@opi-one(192.168.6.114):~# df Dateisystem 1K-Blöcke Benutzt Verfügbar…

Hello all. I am having problems making nand-sata-install script work for installing to my external HDD. I used this (or similar) script in the past on loboris' images and it was working. After some time and experimenting with other images etc. I settled on Armbian, everything worked great, until I started the same script. I made 30 ish GB partition for the system and leave the rest as NTFS storage partition for mounting it later on the OS. But with armbian's script, i couldn't get my HDD to work with it. I am choosing to boot from sd and system from USB (sata) option, choosing the correct partition (/dev/sda2 in this example) and starting the process but it f…

Hello! I build my own image using the provided scripts. I want to be able to run a headless opi system just with ethernet and two usb wireless interfaces. The lastest build works fine when you are using it but doesn't boot if a HDMI cable is not connected. If you boot it with a HDMI plugged in there is no problem, boot ok, ethernet up and all right. I think that could be a configuration of u-boot but there isn't config files in the filesystem of the pi. Anybody kwow the solution? Thanks!

Hi! I'm using a mosfet to control a fan based on temperature on my opipc, but now it just turns on and off. I'd like to control the rpm with pwm, but I cannot use any of the pins with wiringop :S I read on an other forum that the h3 has only one pwm, but which one is the pwm pin, and how could I use it? Thanks in advance!

Hello everyone, I've recently bought an OrangePI PC Plus with an intentions to make it (beside others) a multimedia center. Because of community and pretty good status of armbian on h3, I've downloaded and installed (a.k.a copied to sd) the latest armbian I found (5.20 with kernel 3.4.112). Everything went ok, I've got graphical desktop, hw accelerated h264 and h265 over hdmi to my tv. So the next step was to install kodi. An that's the point where my troubles started. After I installed kodi and probably updated the whole armbian (apt update && apt upgrade && apt dist-upgrade), I noticed that my TV turns off almost immediately I turn it on to h…

Hello, I am trying to communicate with a mcp2515 breakout (8Mhz oscillator) on an Orange Pi Pc+ I have modified the breakout following info on Raspberry Pi: HowTo/Quickstart MCP2515 to keep logic level @3v I have two other nodes composed by two Arduinos, with same (not modified) breakout, one that transmits the other receives. I have successfully tested the first breakout (used on OPi) with an Arduino (powered by 3.3v and 5v on TJA1050). It lets me think that hardware is OK. Below photos of wiring (nb: orange wire becomes red, is wired near TJA1050 = 5v): It seems I have the same results with (edited) user_overl…

After I got my OPiPC+ to finally boot without HDMI, it wouldn't boot in my shop. I originally had it in the bedroom because that's where a convenient HDMI TV was AND that's where the U-Verse router is. In the shop, it went through an HP Procurve 2626 switch but would hang early in the boot process. Logged into the switch and found that most ports were set to "100FDpx". I changed the Pi port to "Auto100" and within seconds, the Pi was booting. Yay! Most people won't have such a problem using ordinary switches. A year ago, I needed more ports in the shop and got a great deal on this one locally. I didn't need 24 ports or the feature set but it was $40.00. T…

Hello, I am using Orange Pi PC Plus with Armbian Nightly. Since upgrade to kernel 4.11.0 audio stopped working, on kernel 4.10.11 everything was alright. When I am trying to open alsamixer i get error cannot open mixer: No such file or directory Can I fix it somehow? Can I still get last image with 4.10.11? Unfortunately it's not available at download page (too late).

I've tried to downgrade the kernel with the armbian-config tool, but now the opi+2 hangs while booting from emmc. I can boot via sd card, but i dont know how to fix the problem - please help.

i've built and started testing stretch ... it mostly looks pretty good with these issues found so far lircd - goes wild. systemd goes to 100% cpu it need to be blacklisted or the like. stopping/disabling it didnt work. i need to remove it to stop the cpu usage problem https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=860551 install python-wheel as default package as pip breaks without it eth0 has gone but seems to be a known issue https://irclog.whitequark.org/linux-sunxi/2017-09-19 and I see that hdmi has made progress (by smaeul) https://irclog.whitequark.org/linux-sunxi/2017-09-26

I have no need at all for the built in wireless on an Orange Pi Zero board. Is there a way I can disable it entirely to save power? Through the DT or some other means? Thanks!

I built Armbian Edge from source (bookworm, server, no gui) and have no video via HDMI. Being a new build, networking is not set up and so I cannot SSH in to troubleshoot. I reverted to a stable Armbian build on another SD, upgraded that kernel to Edge, and lost video output. This one already has networking set up, I can SSH in, but I don't know what to look for in order to get my monitor working. Goal being, figure out what needs changed, and change it in the build process for a new image. I appreciate any pointers.

Hi all, I'm trying to access the GPIO from python context and I absolutely need to do it in a rootless way. (WSGI apache module) I'm a newbie and noticed that this is the library command causing the error inside the python library: Code: Select all fd = open("/dev/mem", O_RDWR); I do have /dev/mem on my armbian distro and clearly the access to /dev/mem is root limited, what's worst I don't have /dev/gpiomem Is there a way to create /dev/gpiomem so I can add the apache user to gpio group and solve this? Do I need to configure and compile a kernel by myself? please help me, thank you

Hi! I recently upgraded the OS of my OpiZeroLTS, from the Debian Stretch Server 5.3.5 (available distro on Sunxi website) to Debian Buster 5.8.5 (downloaded from armbian webpage). Everything went well, except when I plug my USB webcam several video devices are assigned. I made a script with fswebcam to acquire still pictures from all /dev/video* and these "ghost" cameras are causing errors when the software try to open them as regular webcams. My script: for vid in /dev/video*; do output=$(basename $vid) fswebcam -d $vid -r 1920x1080 -D 10 -S 5 -F 1 --jpeg -1 --no-banner --no-timestamp --no-info /opt/images/$output mv /opt/i…

Hello .. I have tested both current release 24.2.1 (jammy and bookworm) on OPiZero, and usb otg not working .. on both .. Kernel is 6.6.20-current-sunxi module g_serial is loaded ttyGS0 exist serial-getty@ttyGS0.service is runing dtc overlays are usbhost0 - 3 ..all looks good on opizero side ... but on "computer side" not.. nothing happened when usb cable is plugged in .. no ttyAMC0 device was created .. no new usb hardware can be found in system log ... ..nothing.. Buster version works well... (my old installation) any advice ..? or it is any "actual kern…

Last year I started a solar-sensing project with the Orange-Pi-Zero (256k), Armbian5.25, legacy kernel and made it work after a while. The Wifi funktion was rather poor and deteriorating, so I ordered a new OpiZero-Plus2-H3, same physical shape and connectors (I thought). Now the -P2 Armbian image 5.30 for the new board loaded perfectly, the Wifi function is really improved due to better hardware. The python part of the code works (still) perfectly. Only (most of) the gpio-functions of my project do not work any more with the new board attached. I use PA07, PA13 and PA14 for bit-bang gpio and a 1-wire sensor via the kernel. I modified the OPi-P2 fex file, shipped wit…

I can not install the plugin because of the missing of linux-headers-4.8.4sunxi Did anyone tried to instll this on a banana pi pro

Hello, I leave in a place where we occasionally get really heavy storms or the power gets cut for some reason. This most often does not happen more than five minutes, but there has been longer cases. Now, this poses an obvious problem with my headless server (Orange Pi PC btw). I went on a week trip last month, to discover the development board I needed was completely down. I called a friend and the power had indeed been cut off in my neighbourhood, but my server would no longer respond over SSH. I hard reset the server by power cable and tried restarting sshd (after getting home a week later), just to get warning that the action of the service was queued and afterwards w…

I have a solar application for PC, so my goal is to reduce the power consumption in idle as much as possible. How would one go about this with the latest armbian distros?

Hi everybody, I have an OPZ board (256 mb). I couldn't manage to start work wifi in automatic mode. I tried manual configuration then tried nmtui in both cases wifi starts only after Ethernet plug was connected. OS: ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i How can I solve this problem? Thanks!

I use the Armbian_5.45_Orangepizeroplus2-h5_Debian_stretch_next_4.14.44.img. I want to use a sensor based on the spi protocol. In armbian-config i enable the spi ,the armbianEnv.txt like this: verbosity=1 console=both overlay_prefix=sun50i-h5 overlays=i2c0 i2c1 spdif-out spi-add-cs1 spi-jedec-nor spi-spidev uart1 uart2 usbhost2 usbhost3 rootdev=UUID=bb48b498-7bd1-4018-b77d-ba00fa61a33d rootfstype=ext4 param_uart1_rtscts=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u But in /dev on spi-dev root@H5:~# ls /dev/s shm/ snd/ stderr stdin stdout Is it because there is no code adaptation spi-dev? if not ,I want to try to transplant th…

Is there some DT overlay to enable or some software to install to use the onboard bluetooth radio of the Orange Pi Zero Plus 2?

I have an orangepizero (https://www.armbian.com/wp-content/uploads/2018/02/orangepizero.png) I installed Armbian_5.90_Orangepizero_Ubuntu_bionic_next_4.19.57.7z on 32GB sd. The pi0 is powered via pin with a 5V/5A power supply, norflash mx25l1606e. The HDD is a new working 80gb maxtor powered by an external USB 2.0 box. I have also connected the serial and read the boot information. I used armbian-config and transferred armbian to HDD and it works, but I have to keep the miniSD plugged in. I ask you can boot from HDD and not use any SD? PS I read almost all posts here on the forum and tried the old procedures but it does not work. Spoiler =&g…

Hey there So I was planning on using the OPZero on a robot that I had already made, which took use of SPIdev, and it was doing calls to the spidev driver in C. Now I noticed that the OPZero has 2 SPI channels, one for the NOR flash (Which isnt populated) on the back and another that goes to the GPIO headers on the device. Now I ran my script, and turns out that /dev/spidev0.0 is actually writing SPI commands to the rear SPI channel. This is apparenly SPI0 according to the schematics. Now following the schematics again, I want to access SPI1, which currently does not exist as a spidev file. I tried "modprobe spidev" to bring up the extra interface, but sadl…

After the automatic update to kernel 4.19.17 the CPU temperature is wrong and much higher, also in dmesg there are these errors Spoiler dmesg | grep thermal [ 6.428747] thermal thermal_zone1: binding zone cpu-thermal with cdev thermal-cpufreq-0 failed:-22 [ 6.841480] thermal thermal_zone0: failed to read out thermal zone (-110) [ 6.841546] OF: /thermal-zones/cpu-thermal: arguments longer than property [ 6.841560] thermal thermal_zone2: failed to read out thermal zone (-110) [ 7.877181] thermal thermal_zone0: failed to read out thermal zone (-110) [ 8.050346] thermal thermal_zone2: failed to read out thermal zone…

This simple tutorial to explain ho wto manage the GPIO with the I2C bus and C++ under Netbeans .

Hi i wonder why ISR result is strange first i test in orangepi zero Plus H5 that result is repeated infinite recall function summary - recall infinite function if i input interrupt pin(button) i test result repeat second i test in orangepi zero(H2) that result is only called function once #include <wiringPi.h> #include <stdlib.h> #include <stdio.h> #include <unistd.h> void signal_both(void){ printf("Signal Both\n"); }void signal_falling(void){ printf("Signal Falling\n"); }void signal_rising(void){ printf("Signal Rising\n"); }int main(int argc, char **argv){…

orange pi one armbian buster purged non free software I installed flashrom. In sudo armbian-config -> system settings -> toogle hardware I marked spi-spidev. Saved. Restarted computer. /dev/spi* displays nothing. How can I enable spi in armbian? Thank you.

Hi. I'm having network problems at last armbian (Armbian_community_24.11.0-trunk.130_Orangepi3_bookworm_current_6.6.44_minimal). Link drops ethernet RTL8211E all the time and sometimes board won't come out of reboot. Any ideas? [ 2.392800] dwmac-sun8i 5020000.ethernet: IRQ eth_wake_irq not found [ 2.392834] dwmac-sun8i 5020000.ethernet: IRQ eth_lpi not found [ 2.393489] dwmac-sun8i 5020000.ethernet: PTP uses main clock [ 2.393545] dwmac-sun8i 5020000.ethernet: Current syscon value is not the default 58000 (expect 50000) [ 2.405541] usb 2-1: USB disconnect, device number 2 [ 2.501691] dwmac-sun8i 5020000.ethernet: No HW DMA feature register supported …

My Development board is Orange Pi zero plus2 H5. My bluetooth already in work,but I try to play a .wav for test.this circumstance occurs. This is my test wav file: 1045.wav I use : aplay 1045.wav Playing WAVE '1045.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo then I record the sounds as mypaly.mp3. I guess this problem is due to uart Baud rate 115200 is not high enough . How can i fix this? 1045.wav mypaly.mp3

firmware version: Armbian_20.02.1_Orangepilite2_bionic_current_5.4.20.img ================= cmd log [dengzy@opl2 ~]$ sudo modprobe sunxi-cir [dengzy@opl2 ~]$ lsmod | grep cir 2:sunxi_cir 16384 0 3:rc_core 45056 1 sunxi_cir [dengzy@opl2 ~]$ ls /dev/input/ by-path event0 mice [dengzy@opl2 ~]$ evtest No device specified, trying to scan all of /dev/input/event* Not running as root, no devices may be available. Available devices: /dev/input/event0: axp20x-pek Select the device event number [0-0]: ^C [dengzy@opl2 ~]$ ================= Also no new log in dmesg when I excute modprobe, loo…

What is the max current that the Orange Pi Plus (or other boards) can output for USB devices? Assume there is a high quality 3A power supply. For example, on Raspberry Pi it is documented here: https://www.raspberrypi.org/help/faqs/#powerReqs Note that the output amount is configurable on RPi (you must manually enable 1.2A output) - is there anything similar for OPi? Here is what needs to be changed in the boot config on an Rpi to change the power from 6mA to 1.2A: http://elinux.org/RPiconfig#USB_Power Thank you!

I've a problem with latest Armbian Debian Server stretch (ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi, Uboot loader 2017.11) on OrangePI One, and OrangePI PC. It boots seemingly OK, but without any output to 1080P HDMI monitor. So I've no video. But Ubuntu Desktop with Legacy kernel boots fine using the same SDCard (and same power supply ). I can SSH to the Debian after boot, here's the boot and diag log. Couldn't wait for senseless SDCard testing to finish, as it works perfect with Armbian Ubuntu Desktop version. Legacy version on 1st boot shown boot progress and defaulted to 720P resolution, which I changed later to 1080P. But Debian Server doesn't sh…

Hello, First I want to thank you for wonderful linux distribution it was been awhile since I last used it, and lot of things changed for me. So I need someone to point me in right direction to catch up with some changes. i'm using Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14 First thing I do not see is script.bin - I use to configure gpios, which one gonna be uart, spi ........ etc. How can I do that now. Second thing is h3consumption tool, I usually use it do disable some system components, like usb in order to lower cpu temperature. I found answers to other things so far using google. So if someone point…

Hello! Does anyone know how make hardware reset of the Pi one board?

Hello! I have: 1) Orange Pi PC+ with ARMBIAN 5.38 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i 2) Orange Pi Zero with ARMBIAN 5.60 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i 3) Orange Pi PC with Debian 3.4.39 #1 SMP PREEMPT Wed Sep 16 13:39:07 CEST 2015 armv7l On both ARMBIANs I have noticed: every start of arecord sets level on "MIC1 boost AMP gain control" audio setting with constant value 5. I think it uses value of "cap_vol=5" from section [audio0] from script.bin. On Debian it does not. In my case I need very very very low value of "MIC1 boost AMP gain control". Value of "ADC input gain ctrl" is alread…

I'm trying to get an MCP2515 working with an Orange Pi Zero LTS H2+. Everything seems to go well until I try to bring up the can0 interface using the command ip link set can0 up type can bitrate 500000 Once the command is entered, it never returns. Control+C doesn't do help. New SSH sessions fail to start, but pinging the IP address works fine. Trying ifconfig from the serial terminal will also fail to return. Trying to shutdown after the "ip link set..." command, the shutdown procedure takes a long time, and eventually sends [ 4320.026984] systemd-shutdown[1]: Waiting for process: ifdown, wpa_supplicant, NetworkManager, …

I was updating some images and thought the Orange Pi + had been retired ... but there was no Support Ended note. I see a lot of other Plus versions of Orange pi boards listed, but not the plain Orange Pi +. Seems easy to miss ;] A little searching found the Orange Pi + is supported https://www.armbian.com/orange-pi-plus/ Am I just missing the link in Downloads? The only way I've been able to get to the page is by direct url or a duckduckgo search https://duckduckgo.com/?q="orange+pi+plus"+armbian&t=raspberrypi&ia=web

Hey, i hope this has not been answered already but i could not find it. I also hope this is the right place to report it. The orange pi + does not appear in the list of devices https://www.armbian.com/download/?tx_maker=xunlong but there is a download page for it you can reach by the search. https://www.armbian.com/orange-pi-plus/ i assume its a bug in the web page?

Hi. Yesterday tried new images - Debian+Ubuntu. In both cases - my wireless Logitech K400 is not working in all 4 usb. (no problem with keyboard connected to windows laptop) Any suggestions? Thanks.

Hi everyone, I'd like to ask and confirm: is there any working HDMI method with proper resolution currently for the Pi+2E, as of 5.59? I'm asking because I have tried next, I have tried dev, and I have tried the legacy kernel. None of them gave any satisfactory result at all. Mainline Kernel 4.14 -- There is HDMI graphics, but the resolution is stuck to no more than 1024x768. I read many times that this is the case when the HDMI was not detected. Kernel 4.18 -- Same thing as for 4.14. Though, as far as I know, the 4.17 should have support for HDMI. Has HDMI for H3 really landed in 4.17, or have I read wrong all over the place? …

A couple of years ago wifi worked without any problems on old version of Armbian, but on the current version It doen't work completely. Any suggestions? uname -a Linux HAMServer 5.4.45-sunxi #20.05.4 SMP Sun Jun 14 21:46:20 CEST 2020 armv7l armv7l armv7l GNU/Linux lsmod | grep 8189fs 8189fs 1069056 0 cfg80211 413696 1 8189fs ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.88.16 netmask 255.255.255.0 broadcast 192.168.88.255 inet6 fe80::8385:e766:9c48:e593 prefixlen 64 scopeid 0x20<link> ether 02:81:a4:6e:47:9e txqueuelen …

I recently updated from very old Armbian image. The update was not smooth so I had to re-image my device with the newest version. After that USB devices cannot be detected at all. I tried USB keyboard and 3D printer (is should looks like generic serial device). Keyboard works perfectly during u-boot but stops working as soon as kernel starts. lsusb doesn't show any devices: $ lsusb -t /: Bus 09.Port 1: Dev 1, Class=root_hub, Driver=musb-hdrc/1p, 480M /: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus…

Hello, We are using Orange Pi Zero with Armbian Bionic with Linux 5.4.20-sunxi armv7l GNU/Linux we are facing a problem, our orange pi heats up some time during processing and then freezes. We can ping the devices, but ssh stops working and all the application don't respond We followed the suggestion in thread: https://forum.armbian.com/topic/7848-mysterious-freeze-and-overheat-of-orange-pi-zero/?ct=1587196371&_fromLogin=1 But output of "armbianmonitor -m" is as below Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 11:19:37: 1008MHz 0.18 6% 1% 4% 0% 0% 0% 76.4°C 0/4 11…

I wouldn't ask for help here if I could find enough information to solve my problem. My program takes user-space GPIO interrupts as signals. It depends on this feature and GPIO interrupts are not replaceable. Testing code is as follows (on Pin12/PA07/GPIO7) by using SysfsGPIO: echo 7 > /sys/class/gpio/export echo in > /sys/class/gpio/gpio7/direction echo falling > /sys/class/gpio/gpio7/edge Check if it works with command `cat /proc/interrupts`: watch -n3 "cat /proc/interrupts | grep sunxi_pio" After configuration, give GPIO7 a pulse by attaching it to 3V3. This method does works on Orange Pi 0+ H5 running Ar…

Hello everyone, asking your help as i'm getting a little bit crazy with my pi02w. I'm not able to understand why my board is not able to connect to wifi without the external antenna. I'll explain better, it seems that is able to find it, connect to but not able to work. I cant post the armbianmonitor log as no internet connection. Thanks armbianmonitor.txt

Hi all, First, thanks to Igor for his job with Armbian: Scripts, compilations etc. Very apprecied so far. I own an Orange Pi 1 based on A20 SoC. Armbian kernel 4.4.1 is installed, no problem. (I have used the Igor's script to upgrade it) But I'm trying to change the bin file in /boot/bin, it seems to not work, no change if I set screen0_output_mode = 5 In orangepi.fex Of course, I'm using the bin2fex & fex2bin exec on my desktop (Kubuntu 16.04 x64), and I copy the new bin file in /boot/bin/orangepi.bin The goal is to change the first resolution, because I would like to solve this problem (see the photo, the display exceeds) on my DIY tablet. …

Hi, I'm trying to set up my Orange PI 2 with very specific resolution. I tried a lot of advices from this forum but still can't force it to work. I've used jernej's U-Boot to see correct parameters for monitor and then recompiled kernel with these params. There is U-Boot output: hdmi_core.c line: {MODE_XXX, 0, 297000000, 0, 2160, 1200, 2266, 46, 40, 20, 1464, 234, 28, 2, 0, 0, 0, 0, 0} hdmi_bsp_sun8iw7.c line: {YYY, 1, 0, 0, 8, 2, 4, 0, 28, 0, 0, 112, 106, 40, 20, 176, 264, 1, 1} script.bin setting: pll_video = 297 My monitor is connected by HDMI cable, I set my mode using "h3disp -m" command and also I tried different params in "[hdmi_para]" section in scrip…

hi Both the last img based on ubuntu for orangepi 2 and orange pi plus E doesnot run. LED doesnot light. Normaly i used old armbian img based on jessie 5.25 ( plus E ) nad 5.05 ( orangepi 2 ). It works. I download the new ones but nothing happend - black screen only...

Hi, It is nice to join in and be part of a such fast growing UOS. I would like get some advice and solve the following scenarios: * Internet Sharing with one Client only, no 'switch' needed, this has been accomplished with the instructions in https://wiki.archlinux.org/index.php/Internet_sharing, so all the iptables rules and NAT is done with success. I am able to navigate the internet from OPI-PC. * which armbian version for the smallest server to run on OPI PC, that will provide some web services. * Need to be able to access OPI-PC from the external world (from PC-3), this is what i am struggling to get it right. Say i want to connect to OPI PC …

Hi, I need to use the GPIO of the orange pi, is there a library that i can use to program my aplications in java or python? Is pi4j an good option? Can i use it with orange pi plus 2?

Hello, I have Debian 8 with XFCE Desktop installed on my Orange Pi 2. I downloaded the OS image from the orangepi.org a while ago and everything works OK except the WiFi. Does Armbian support the onboard WiFi of the OP2 ? If yes then I will change the OS today Thank you

Hi, I recently reinstalled an orange pi 2+ with Armbian Stretch mainline kernel 4: root@ted1090-7:~# uname -a Linux ted1090-7 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux I also installed it on EMMC (this way, with this u-boot-sunxi-with-spl.bin). Now this orange pi crashes every couple of days (sometimes with a couple of hours). This orange pi use to run with Armbian legacy 3.x kernel on EMMC without any issue: pi@ted1090-6 ~ $ uname -a Linux ted1090-6 3.4.113-sun8i #18 SMP PREEMPT Wed Jan 24 22:10:49 CET 2018 armv7l GNU/Linux Exactly the same applications are installed (dump1090 and dump1090-tools). T…

Hi, I'm using Orange Pi 2E+ with 3.4 Multimedia kernel (intend on using Kodi) I have a DVI monitor I want to use, and a crappy HDMI > DVI adapter which for some reason doesn't let computers know that the DVI monitor is connected to their HDMI port Confirmed on 2 different computers. The adapter probably lacks the hotplug-detect pin because computers don't know there's a screen connected, but the screen will show an image if I force my laptop to send a video signal out it's HDMI port using xrandr. Is there a way (using .fex files or whatever) to make the kernel assume that there's a monitor with 1920x1080 resolution on the Orange Pi 2E's HDMI port? …

I have an orange pi 2e running armbian, after using armbian-config to switch to the mainline kernel, my board wont boot ( no display output ) I tried running armbian with a new image on a SD card but the board wont turn on ( also no display ) any ideas?

You need to connect the equipment via the I2C bus with a frequency of 1 kHz or 10 kHz to Orange pi 3 (OS Armbian Buster with Linux 5.3.9-sunxi64). Supported setting of these frequencies and how to change correctly? Recoded sun50i-h6-orangepi-3.dtb to dts: cd /boot/dtb/allwinner/ dtc -I dtb -O dts -o sun50i-h6-orangepi-3.dts ./sun50i-h6-orangepi-3.dtb nano ./sun50i-h6-orangepi-3.dts What should be done next to set the frequency of 1 kHz or 10 kHz to the i2c-0 bus? Thanks.

Hi, Sorry, I don't know if correct topic, but I have a Orange PI 3 and have problem with DNS resolution. I tried with image Armbian_5.82.19042 based in Debian and Ubuntu but is imposible make to work. I added the line net.ipv6.conf.all.disable_ipv6=1 in /etc/sysctl.conf file but this change not resolved the problem. For example if I try to ping www.google.com sometime take a 25 second for DNS resolve to IP address. I don't see any problem with my local network because I have other devices that not have any problem with DNS resolution. Please, your help.

Hi everyone, I am trying to set the pin 26 (PL08) on orange pi as Input but sometimes it is flashing. I did put a 10K external pull up resistor and it is exported as input pin. I did the same thing with the pin 22 (PD21) and this one is steady, no problems until now. I did not add anything on overlays for these pins. Any idea what I am doing wrong? Thanks

Hi community To use Kubernetes (K3s) on my Orange Pi 3 I need to enable cgroups. I running currently on Armbian Buster (20.08.1) As I understand this needs to be enabled on build-time (?) or is there any other way to enable cgroups? Is there any other image which has cgroups enabled? any support is appreciated many thanks Daniel

I have a headless Orange pi 3 and wanted to be able to test a new install. Is it possible to issue a specific reboot command that will switch to boot from one storage to the other storage? I have armbian bionic installed and running on the EMMC. and A new bionic build installed on a new SD card. So, if i'm tinkering with the new build on the SD card, can i reboot to the EMMC without removing the SD card, and then similarly reboot from the EMMC into the SD card build??

After installing the Bullseye version in the Orange PI3, I launched the Kodi installation. The videos however are in slow motion, with the audio at normal speed. Are there any codecs missing? The video driver? Thanks

I am trying to access control on Orange PI 3 , H6 some gpio,s using "gpiod" package that I installed from here : apt install gpiod I cannot control gpio's from port L such as 360, 354, 355 , ... +------+-----+----------+------+---+OrangePiH7+---+------+----------+-----+------+ | GPIO | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | GPIO | +------+-----+----------+------+---+----++----+---+------+----------+-----+------+ | | | 4.3v | | | 1 || 2 | | | 5v | | | | 123 | 0 | SDA.0 | ALT2 | 0 | 3 || 4 | | | 5V | | | | 122 | 1 | SCL.0 | ALT2 | 0…

Hello, The Orange Pi 3 ARMBIAN image is no longer available on ARMBIAN Website, is there any way to get it ? https://www.armbian.com/orange-pi-3/ Thanks

I have a problem flashing the oranges. I flash it with a 32G SD card with Linux with a network cable directly to the switch. After the process is finished, I turn off the orange and remove the card and turn it on again, but the orange LED (communication) on the network card stops working. This occurs in every 10 oranges flashed, 1 or two this type of error occurs. What is the solution?

When I attempt to run the Sudo apt update command I am receiving an error message about the Repository not being signed. See attached photograph

I am getting significant graphical issues with most programs on the "Jammy Gnome desktop" version. I also saw similar issues under KDE desktop after clicking a button relating to OpenGL in the graphics settings (and couldn't figure out how to get that dialog back or undo the setting). I would prefer to stick with Gnome, I assume this issue has something to do with hardware/graphics acceleration having an issue, the application launcher seems to be immune from the issue. Sorry, I am quite a noob when it comes to Linux/programming related stuff, I couldn't find any other mentions about similar issues in this forum. The issue happens on both this 5" LCD and an HDMI TV at 4k.

Orangepi 3 LTS Armbian 22.05 Jammy XFCE CAN'T CONNECT WITH WIFI

Hello everyone! Yesterday I downloaded "Armbian 23.5 Jammy". Unfortunately the integrated wifi module does not work. I tried several alternatives but with the same problem. I am not an expert on the subject. Any solution? I'm trying to compile and in one of the steps it tells me that the "Orange Pi 3 LTS - H6" is no longer supported. If anyone knows and can help would be appreciated. https://paste.armbian.com/varepekose Original: Hola a todos! En el dia de ayer descargue "Armbian 23.5 Jammy". Lamentablemente no funciona el modulo wifi integrado. Probe con varias alternativas pero con el mismo problema. …

Hello, dear members! I built the mainline kernel 6.0.8 using the config-5.15.80-sunxi64 config, but when I try to boot the system hangs on Starting the kernel. Boot log: U-Boot 2023.01-rc3-00069-g93685d0dcb-dirty (Dec 19 2022 - 11:31:13 +0300) Allwinner Technology CPU: Allwinner H6 (SUN50I) Model: OrangePi 3 LTS DRAM: 2 GiB Core: 50 devices, 14 uclasses, devicetree: separate WDT: Not starting watchdog@7020400 MMC: mmc@4020000: 0, mmc@4022000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial@5000000 Out: serial@5000000 Err: serial@5000000 Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0,…