Allwinner sunxi

Hello, I am developing a project that will use the ethernet module ENC28J60 on orangepi pc plus, but I do not know how to configure armbian to enable using the module. Searching the internet I just found solutions for raspberry. I have already enabled the spi-spidev option using the armbian-config tool. What should I do now? Thanks.

hi, I'm trying to use an OrangePiPC2 H5 processor on an old TV. I have got to edit the dts file but I dont know what to change to antivate RCA video & audio output. Plz, help me to set RCA port as default or give me links to learn to edit dts, I've seached a lot but found nothing. thx

I flashed the latest Armbian image on my NanoPi Neo 2 Plus's emmc. According to https://linux-sunxi.org/Linux_mainlining_effort I2S is not part of the mailinke kernel for H5. I can use I2S with Friendlyelec's images. However, I prefer Armbian. Is it somehow possible to use I2S with an Armbian image on this board?

After some months not using my OrangePi One, yesterday I installed Armbian 5.90 buster 4.19.57 (previously I had a stretch release). I did a clean install, downloading the image and burning the microSD with it. I noticed the button now works for 1st time since I bought the OrangePi One. It shuts down the device, no need to install or configure nothing. But, previous Armbian versions I had, were able to set the machine CPU speed at 1.2 and 1.1 GHz. Now (with Armbian 5.90) the maximum is 1 GHz. On previous releases, the file /sys/devices/system/cpu/cpufreq/policy0/scaling_available_frequencies contained: 240000 480000 648000 816000 912000 9…

I know Lamobo-r1 has many problems and that the support ended, but it works fine for me. Everything works fine with kernel 4.14.84-sunxi, however, when I update the kernel, the b53 switch does not work anymore. I need to update the kernel to add another wifi usb dongle that seems to work only with newer kernels (https://github.com/aircrack-ng/rtl8812au/issues/272#issuecomment-467983704). Anybody experiencing the same problem? Any ideas for a workaround?

Hi, I'm new to the Armbian/Alt PI scene, coming from a RPI Zero W. I'm needing to interact with my PI using a CH340G (is it compatible) USB to TTL dongle. I've also trjed a CH351A device, put it into UART mode. Unfortunately, I get nothing from the PI. Despite using the primary RX/TX pins. I've also tried enabling all of the UART pins using armbian-config, and using another set of pins - to no avail. Please view my setup below. I've run out of ideas of where I'm going wrong. I've tried these images: Armbian_5.90_Nanopineo2_Debian_buster_next_4.19.57 Armbian_5.90_Orangepione_Ubuntu_bionic_next_4.19.57 Refer…

As I told on another topic, yesterday I installed Armbian 5.90 buster 4.19.57 on my OrangePi One. Now, when it boots, all the output text goes to the bottom line of the screen, with each line overwritting the previous one (no scroll). Then it asks for username, and when I type it it asks for password, overwritting the username I typed. And it probably displays the wellcome banner, but I just see the last line of the banner. Once logged, I have to type "clear" and then I can use the full screen, and it scrolls. That happens on the console, if I start a new session from another machine (using PuTTY) it works fine. My password …

Hi, who knows how to fix the problem of the displaced screen on the right? This is how Armbian appears with the latest build https://dl.armbian.com/orangepi3/nightly/Armbian_5.90.190705_Orangepi3_Ubuntu_bionic_dev_5.1.15.7z and this is how it appears to me with an old build with kernel 5.0.7, so it's not the monitor's fault Regards

I encountered a very strange boot behavior on OrangePI Plus 2E. When I boot from SD card with the desktop Armbian image, I'm having just an input of some color on HDMI (photo attached). No U-boot output on screen, but considering UART output both U-boot and system boot with no errors (log file is attached). Boot with the server Armbian image goes just fine, except no U-boot output on screen (only on UART) and screen resolution is 1280x720, while native resolution for the display is 1920x1080. Until recently everything worked just fine with both desktop and mainline images, and U-boot giving proper output on screen in 10920x1080 resolution. What I tried so far: …

Hi, I can't make usb otg works on orange pi pc armbian stretch. Linux orangepipc 4.19.38-sunxi #5.83 SMP Fri May 3 23:33:25 CEST 2019 armv7l GNU/Linux At boot there is the following message in dmesg: [ 2.252841] usb0-vbus: disabling I tried to enable usbhost0 with armbianconfig overlays, but it doesn't make a difference. Any suggestions ? thanks

Im trying to connect WaveShare 10" Touch Screen LCD (HDMI) to OrangePI Plus 2E but the problem is that I got greeny picture on the screen. If I connect this display to Raspbery PI 3 I got good clear picture. Any ideas what could be wrong and how to fix it?

Hi, Lime2 A20 not even detecting mini usb ethernet, which was working perfectly fine on 3.xx. Manfu: Netgear USB: USB 2.0 Ethernet Adapter P/N: 322-10167-01 dmesg doesn't even list the device. Could board's port be damaged? I tired usb port with usb ethernet, it lists as: I'm using arbmian Ubuntu 18.04 with beta packages. Thanks

I use OrangePi R1 with connected RS485-TTL module to UART1 (PG6, PG7). RS485 communicates with a heatpump. Heatpump transmits data to RS485 module and I read and decode the data with a program and make some ACK replies. Everything worked fine for a month till OrangePi Power Adapter died. I have replaced Power Adapter and my program now stopped working. I have already spent couple days debugging. Replaced the cable from the heatpump to RS485-TTL module. Tried to see what is happening on the RS485 line with oscilloscope. Start of the diagram always looks good, but the end is skewed and corrupt. It seems like RS485 tries to send data while it receives and ce…

Hello, I have fresh new board from olimex - olinuxino a64, and tried to install both debian and ubuntu images, but non of them has ethernet working. I already tried to edit dtb file and incread tx-delay-ps, but with no success. Has somebody a functional dtb file for this board? Thank you for any answer!

Can the Audio port on the Orange Pi Win Plus A64 also output video (like TV output)? It seems like most of the orange Pi boards with an audio jack can do this and the CubieTruck (which is an A20 board) can do the same as well. Please let me know ASAP. Thanks!

I am searching for an LCD 10 inches or above that works with the LCD connector on the Orange Pi Win Plus A64. Does anyone know of one that works and can you provide a link to it so I can purchase and use it? Thanks.

Ubuntu Bionic, crash on linux-image-dev-sunxi64 5.88.190602, 5.88.190603 and 5.88.190604 (all kernel 5.1.6?) Last worked was 5.88.190601 (kernel 5.1.5) Debug log before crashing (full log in attachment): [ OK ] Reached target Network (Pre). Starting pNFS block layout mapping daemon... Starting Create Static Device Nodes in /dev... Starting Apply Kernel Variables... Mounting Kernel Configuration File System... [ OK ] Started pNFS block layout mapping daemon.…

Hello, Could you please somebody advise me with hostapd issue? I installed on new Orange Pi R1 new Armbian: ARMBIAN 5.59 testing Debian GNU/Linux 9 (stretch) 4.14.65-sunxi Problem is, that after starting service hostapd system/kernel crashed Some short time is Access Point reachable, but then orange crashed. root@orangepi:~# cat /etc/hostapd/hostapd.conf interface=wlan0 bridge=br0 #driver=nl80211 ssid=Rubikon hw_mode=g channel=8 wmm_enabled=0 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=xxxxxxxxxxxxxx wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP …

hi there my orange pi one is very slow (8 fps) at encoding my capture card stream to h264 using HW Cedrus264 but other 720p mkv files are converted fast using HW (50 fps) then i tried to save the stream first to sd card (720p Mjpeg format) then encode it using HW , but here i still have 8fps , and cpu usage is 40% even when i used SW libx264 to encode , i still get 8fps and cpu 40% wich is weird is it possible to get real time 720p encoding ? , my capture card only output mjpeg armbian xenial desktop

Hello, I installed Armbian 5.84.1 on a A20-OLinuXino-LIME2 a few weeks ago and it works very well: Welcome to ARMBIAN 5.84.1 user-built Ubuntu 18.04.2 LTS 4.19.38-sunxi Today I did a simple apt update && apt upgrade Now the box doesn't boot any longer. On the serial console I see: U-Boot 2019.04-armbian (May 08 2019 - 15:28:02 +0300) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: A20-OLinuXino-LIME2 Rev.C [...] Starting Armbian memory supported …

Hello all. Okay: I am a total newbie to Orange Pi. I apologize upfront for any and all obvious self inflicted mistakes that you all spot. AGAIN: total newbie to the Orange Pi world. Please go easy in me! I have an Orange Pi Win Plus A64 board and frankly --- I love the darn thing! Powerful for my needs and I have a niche application that I am working on and this board is really the only one that fits my needs. The 2GB RAM is a must. The issue I am having is this: I am usinga waveshare 10.1 inch TFT HDMI display that has the SPI connector (lcd: https://www.waveshare.com/wiki/10.1inch_HDMI_LCD). I have att…

Hello, There seems to be scant details about the NanoPi Neo 2 LTS, so I thought I'd contribute some. My testing is much less formal than how some would measure it. What I especially like to do in the way of network speed testing are the "worst-case scenarios". My way of invoking a sort of "torture test" is to mostly test upload speeds (as they tend to be slower than download speeds), both large files (much easier), as well as uploading many tiny files (much more gruelling to store, so is therefore a major "torture test"). Having said that, I'll usually favor all-GbE networking (noting which I'm using, GbE or wifi), because I know GbE will b…

Dear Armbian team, I am using debian stretch with orange pi PC ( Linux orangepipc 4.19.38-sunxi #5.83 SMP Fri May 3 23:33:25 CEST 2019 armv7l GNU/Linux ). At the moment by default when I press the power button, it shutdowns the orangepi pc, and I have to plug off/on the power supply to reboot the device. I would like to modify this behavior, to program custom actions when the button is pressed. If possible it would be nice to be able to distinguish between short press and long press. I tried without success to follow the manual instructions, and add the custom overlay gpio-button.dts. Also tried the acpi package approach without a…

Hi , I'm using orange pi lite (H3) and armbian xenial desktop. When I plug in my adata 8GB flash drive armbian couldn't find it. What should I do?

the new version of Armbian (5.83) Does not boot from sd card I tried to install 5.69 it's work normally. I tried to all the sd card formatter rufus and wın32 disk imager and different sd cards but no way new version does not work anyway. when i burn to 5.69 it boot normally. I guess you have to control the package whıch you upladed for opi pc+ thanks

Hello, I just use the Zero Plus 2 H3 with extension, using Armbian 5.83 but failed to get the combo to play the sound I use the command aplay -l but return no sound card found How to install driver for sound in this board?

I just recently obtained a new Cubietruck A20 and I downloaded the latest armbian bionic, formatted my micro SD card and put the downloaded image on it (with Etcher). The board boots and everything is good .... until I get to the root prompt. The board doesnt boot to the desktop gui at all. Has anyone else experienced this? What steps am I missing? Can someone guide me to the proper armbian install for the Cubietruck a20? I am using an HDMI monitor with it. Thanks.

Hello, I am using nanoPi Neo Core with mini shield nanoPi NEO CORE/CORE2. The OS that i am using is Armbian stretch downloaded from this link : https://www.armbian.com/nanopi-neo/ The armbian image that I am using is : Armbian_5.65_Nanopineo_Debian_stretch_next_4.14.78 If I try to enable SPI without doing update and upgrade, it works. If I do update and upgrade and then try to activate SPI, it is not working. I dont find the spi device in /dev. Any idea what could be the problem? P.S: Before last week, I didn't have this problem. So I think it is related to a recent update done on this image. Thanks in advance. …

TRYING TO create an ad-hoc network using wireless adapter( lb-link model: wn155a) on NANOPI NEO (Linux nanopim1 3.4.113-sun8i #28 SMP PREEMPT Thu Feb 2 02:01:28 CET 2017 armv7l GNU/Linux). we used this link https://citricks.net/create-access-point-linux/ BUT ad-hoc WAS NOT CREATED. running iwconfig looks like: lo no wireless extensions. tunl0 no wireless extensions. ra0 Ralink STA ESSID:"11n-AP" Nickname:"MT7601STA" Mode:Auto Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:1 Mb/s RTS thr:off Fragment thr:off Encryption key:off …

Hello, Unfortunately as I read from forums mainline kernel has no driver for gc2035 and v4l2 driver. I have tried Armbian_5_65 and Armbian_5_59 debian stretch but they are not contains these drivers and eventually modprobe command fails. As I understand, I have 2 different solutions to run camera on my system; 1- Going back to legacy build. But I do not know how to go back the legacy build which is last supporter these drivers. 2- Installing required drivers. (Also I want to prefer this solution because going back to legacy build may cause some bugs) How can I install required drivers to mainline stable build and where can I find …

Hey,I'm using Lg 19M38A 18.5 inch monitor .when I plug in my orange pi , only monitor shows the booting process and then the black screen up .how can I fix this problem?

Armbian Bionic not sound output 3.5mm jack root@orangepipcplus:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0

update: the 5.59.180828 nightly building version may display a error temperature degree。 test real temperature using a thermometer ，two version display the same degree in thermometer about 49degree idle。 1. same board:orange pi zero plus v1.1,same room temp. 2. armbian 5.59.180828 nightly , idle cpu temp. about:49 degree. ------------------------------------------------------------------------------------------------------------- Welcome to ARMBIAN 5.59.180828 nightly Debian GNU/Linux 9 (stretch) 4.14.67-sunxi64 Linux opizeroh5 4.14.67-sunxi64 #85 SMP Tue Aug 28 10:55:16 CEST 2018 aarch64 GNU/Linux Stop monitoring using [ctr…

After connecting the wireless adapter we run the following command: lsusb the output is Bus 004 Device 003: ID 148f:7601 Ralink Technology, Corp. Trying to install armbian driver (Linux nanopim1 3.4.113-sun8i #18 SMP PREEMPT armv7l GNU/Linux) for lb-link model: wn155a "MTK7601 chipset" wireless adapter (150Mbps) using the following commands: sudo apt-get install linux-headers-generic build-essential git sudo apt-get install git git clone https://github.com/flexiti/mt7601.git cd mt7601 make clean make sudo make install sudo mkdir -p /etc/Wireless/RT2870STA/ sudo cp RT2870STA.…

Hello, when I connect R307 fingerprint reader to USB port, Linux identifies it as mass storage device. If the device is connected to the Orange Pi board before turning on, the system resets itself on early startup with "Resetting CPU..." message. What can be the reason and how to avoid it? I know about alternate serial connection, but would prefer to use USB. I use Armbian recent version with console image. Thanks in advance.

Hi folks, i got my orange pi zero a few weeks ago but had no time to assemble it. This evening i got the time but i was in toughts and rubbed an resistor off the board. Can please measure someone the value of the missing resistor? Otherwise iam srcewed :/

Hello Folks! Already successfully running an RTL-SDR device (for Flight Tracking) and U-Blox NEO-6M GPS (for GPS/NTP) on my Orange Pi PC Plus, and now wanted to try a BME280 weather chip, but ran into problems talking to it. The 'i2cdetect' seems to be working fine: darren@frodo10:~$ sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- …

Orange Pi Zero Plus | 5.83 | arm64 | aarch64 | 4.19.38-sunxi64 Hello Armbian community, I set up the wifi with armbian-config, but Wifi connection get lost or after reboot it does not connect again. Is there something I could to. would it help to turn off power management ? how too? looks like i am not the first with this problem: 9213-orange-pi-zero-plus-wifi-looses-connection-tip But if its possible I do not want to turn off the network manager ____________________________________________________________________________________________ …

Hi everyone! I never asked for help at forums, but Opi forces my brain week. I try to create Wi-Fi by means of HostAPD(manual: https://goo-gl.ru/5s05). root@orangepi3:/etc# hostapd ./hostapd.conf Configuration file: ./hostapd.conf wlan0: Could not connect to kernel driver Using interface wlan0 with hwaddr xx:xx:xx:xx:xx:xx and ssid "MyWiFi" wlan0: interface state UNINITIALIZED->ENABLED wlan0: AP-ENABLED ........ (Infinite expectation) ############################# + dnsmasq does not want to work with wlan0, only with eth0. I will be glad if you help me, thanks!

hey guys, Using legacy kernel I have trouble having dual output on LCD and HDMI. I tried to have a cloned dual output (same framebuffer for both) : [disp_init] disp_init_enable = 1 disp_mode = 4 screen0_output_type = 1 screen0_output_mode = 6 screen1_output_type = 3 screen1_output_mode = 4 fb0_width = 0 fb0_height = 0 fb0_framebuffer_num = 2 fb0_format = 10 fb0_pixel_sequence = 0 fb0_scaler_mode_enable = 0 fb1_width = 1024 fb1_height = 600 fb1_framebuffer_num = 2 fb1_format = 10 fb1_pixel_sequence = 0 fb1_scaler_mode_enable = 0 ... Also tried with 2 framebuffers : [disp_init] disp_init_enable = 1 disp_mode = 2 screen0_output_type = 1 s…

Good afternoon, please help configure the rotation of the logs. I am completely new to this system, unfortunately, I can not find a normal instruction on how to configure rotatilog. My problem is that the logs are full, and my necessary scripts stop working. If I constantly clear the logs manually, then the scripts work fine. I tried to configure the rotation in accordance with the instructions, it only works before the reboot, after the reboot, everything I fixed with the rotation changes the paths to /var/log.hdd/. Please help me make sure that all logs do not exceed 1m. and constantly spinning. I apologize in advance if not fully expressed his thought.

I compared two boards （opi zero h3 and opi zero plus h5) and found that cpu pins for 26 gpio are the same . so I modify the code in wiringPi about cpu detection to force return true value . and it works. the step: 1. git clone https://github.com/xpertsavenue/WiringOP-Zero 2. modify the code in WiringOP-Zero/wiringPi/wiringPi.c (or using the attached file to replace）。 3. make && make install 4. run "gpio readall " to test 5. run "gpio write 30 1" (the red-led on, wiringpi pin 30 control red-led status). wiringPi.c

hi when i try to play a video player performance is very low on armbian but when i install android on my board video player performance is good Enoughwith mx player app i try improve performance with overclock cpu but its not helpful how can i improve performance of video player on armbian ? and its possible to play h.265 video and 3d video?

HI I noticed that the Windows 10 on Arm version has the ability to install on mini-pc, like the raspberry pi. My question is, is Windows 10 capable of being installed on the BOARD WITH h5 processor? I USE OF QEMU-KVM FOR INSTALL WINDOWS ON MY ORANGE PI BOARD BUT IT HAS VERY LOW PERFORMANCE AND QEMU ONLY USE OF ONE OF H5 CPU CORE . Is it possible to install on orange pi pc2 armbian and Windows operating systems at the same time with dual boot?

Im tring to access the GPIO using Python3 on a bananapi M1 Linux m5 4.19.38-sunxi #5.85 SMP Wed May 8 14:20:48 CEST 2019 armv7l GNU/Linux I manage to get access to gpio in shell, c, and in python2, but not in python3 with the following software: https://github.com/BPI-SINOVOIP/BPI-WiringPi https://github.com/BPI-SINOVOIP/BPI-WiringPi2-Python The error in python3 is the following (in pyhon2 work) : Traceback (most recent call last): File "/root/src/BPI-WiringPi2-Python/wiringpi2.py", line 18, in swig_import_helper fp, pathname, description = imp.find_module('_wiringpi2', [dirname(__file__)]) File "/usr/lib/python3.5/…

Hello, I want to read data from UART3 on OrangePi One. I want to use UART3 (pin 8 & 10), so I enabled uart3 overlay at /boot/armbianEnv.txt. Now I expect to read data via minicom -b 115200 -D /dev/ttyS3 but I read nothing unfortunately. What am I missing? Any help is appreciated. I'm using Linux orangepione 4.19.38-sunxi (sorry, armbianmonitor doesn't generate link) Thank you, Regards

Hello, I want to read data from UART3 on OrangePi One. I want to use UART3 (pin 8 & 10), so I enabled uart3 overlay at /boot/armbianEnv.txt. Now I expect to read data via minicom -b 115200 -D /dev/ttyS3 but I read nothing unfortunately. What am I missing? Any help is appreciated. I'm using Linux orangepione 4.19.38-sunxi (sorry, armbianmonitor doesn't generate link) Thank you, Regards

I'm trying to use PA18/PA19 for custom purposes. I need to put these pins to Input state without any pullups/pulldowns. What I can achieve is: to put these pins to input state via the command: gpio mode 30 in gpio mode 31 in ("tri" instead of "in" does not work, it accepts the command, but a multimeter shows the input is still high, as well as gpio readall) These pins are probably pulled high because they are I2C pins. I want to disable the I2C functionality but have not found any means to do so. I have tried this dts script: ##### /dts-v1/; / { compatible = "allwinner,sun8i-h3","allwinner,sun50i-h5","friendly…

Hi everyone, I want to create an USB device, for this i am following this tutorial : gadgetfs. It works fine, but when i want to have an endpoint superior to 4, i cannot. I just changed to Unfortunately, in the folder created i have only this files : ep1in ep1out ep2in ep2out ep3in ep3out ep4in ep4out musb-hdrc I thought a usb device can have 32 endpoints. So, is it possible to have an extra endpoint ? And i have an extra question, as a kernel noob, I don't fully understand how this guy came out with thi…

I am trying to set up a video loop that runs continuous on boot up

Hi, I would connect a 7" HDMI 1024x600 Touchscreen display (like waveshare or else) on Orange Pi 3 (as a raspberry). Latest armbian version for H6 CPU support this display ? If a need to use a 7" touchscreen display on Orange Pi 3 how can I do ? Thanks

Banana Pi M1+, kernel 4.19.38-sunxi, Debian stretch I needed to get bus i2c-2 working so I went to armbian-config, ticked i2c-2. After reboot I found some information from PMU were missing, some i2c buses were removed and some added. before crw-rw---- 1 root i2c 89, 0 May 26 18:24 /dev/i2c-0 crw-rw---- 1 root i2c 89, 1 May 26 18:24 /dev/i2c-1 after crw-rw---- 1 root i2c 89, 2 Jun 11 10:29 /dev/i2c-2 crw-rw---- 1 root i2c 89, 3 Jun 11 10:29 /dev/i2c-3 crw-rw---- 1 root i2c 89, 4 Jun 11 10:29 /dev/i2c-4 armbianEnv.txt verbosity=0 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun7i-a20 rootdev=UUID=078696…

Ok. I'm trying to use my orange pi pc for send ir signals to my tv. I'm using lirc on an armbian stretch 9.9. the ir receiver works fine, but when I try to emit with the command: irsend SEND_ONCE tv KEY_5 (tv is the name of my lircd.conf), those ir signals that I previously recorded and saved on my lircd.conf file it shows the following error: Hardware does not support sending error running command: Input/output error Thanks in advance.

Source for kernel in package : linux-source-4.19.38-next-sunxi is for 64BIT architecture , is not possible to get source for 32bit architecture

Hello, I had a telecommunication technician logged onto my router + later that night a power outage. Now my pi (not sure before or after or related to anything), now the lights go on the pi (both + the one on the network), I can see it on the router with an IP but that is it. I can't logon to it on that IP with Putty nor can I ping it from the console on the PC. I tried now 3-4 of the builds (older ones, one official one and so on) with the flash card, but always the same. I don't have an USB to TTL converter to try that route. Is there anything else I can do? There is no way to do a hard reset, right?

Hi guys, I have PCDuino 3 Nano which worked fine on latest ARMBIAN on Debian Jessie which is moving to EOL and armbian support for this board was dropped due to lack of devices. I have used it mainly as OMV sever with sata drive but now I migrate to a x86 install and this board will be wiped as I would like to use at as vpn server etc. What are my alternatives? I know that still are a lot of A20 boards that have armbian support. Which of them I can use and what probably won't work?

Hello! Is there any way to config the frequency used by the DRAM driver when throttling takes place, or even better, disable the DRAM throttling at all? First of all, I have to say that that I'm pushing my Orange Pi Zero H3 board to run at very hot temperatures due to my CPU throttling settings so I can play some retro arcade games (I know I may burn it). But it seems the DRAM driver has its own throttling settings, and it takes place reducing DRAM frequency to 132Mhz. At such DRAM frequency there is flickering at HDMI output. May 13 18:30:31 inova-casa kernel: [15484.645810] [hotplug]: cpu(0) try to kill cpu(2) May 13 18:30:31 inova-casa kern…

I'm powering a small PCB via the OTG port on my OPI PC Plus, however sometimes I need to be able to reboot the device. It is possible to cut power to the OTG port momentarily to force a reboot? I've seen mention of PL2 GPIO, but it is unclear to me how this should be setup. I've also looked at uhubctl, but that didn't work. Thoughts?

Hello, My orange Pi runs with Armbian Stretch 4.19.y. I like to use Orangepi boards, for audio streaming via Alexa Skills therefor I need to install gstreamer plugins apt install libgstreamer-plugins-good1.0-dev Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package libgstreamer-plugins-good1.0-dev E: Couldn't find any package by glob 'libgstreamer-plugins-good1.0-dev' E: Couldn't find any package by regex 'libgstreamer-plugins-good1.0-dev' this deb is only amd64 and i386, but i found this deb: libgstreamer-plugins-base1.0-dev_1.10.4-1+deb9u1_armhf…

Hi I discovered that there are two versions of M64 bananapi. The first version on which all the kernel numbers go. The second version, which is not the kernel 4.19.x - kernel panic. The system will not run. I can not give you memory numbers because I covered it with sticking the heat sink. The first version is a model bought in 2016. The second version is the this year's model. The situation is similar to that of Nano pi T3 +

I am trying to enable memory split on my board. I am using Armbian Stretch with mainline based kernel 4.19.y. No matter what I do, after reboot I get: root@bananapi:~# free -h total used free shared buff/cache available Mem: 996M 170M 613M 4.8M 212M 799M Swap: 498M 0B 498M I've already tried adding to armbianEnv.txt: disp_mem_reserves=on extraargs=cma=96M After first boot I've already relinked /boot/script.bin to /boot/bin/bananapim1plus.bin and added fdtfile=sun7i-a20-bananapi-m1-plus.dtb to /boot/armbianEnv.txt in order to ha…

Kinh nghiệm mở shop đồ chơi trẻ em? Đồ chơi trẻ em là luôn luôn cần thiết và là sở thích tất yếu của con trẻ ,giúp con trẻ phát triển các kỹ năng trí tuệ toàn diện, nhất là những sản phẩm mang tính giáo dục. Các bậc phụ huynh ngày càng có nhu cầu cao về những sản phẩm, đồ chơi an toàn cho con,, giúp con phát triển về tinh thần, trí tuệ và thể lực. Chính vì lẽ đó mà cửa hàng đồ chơi đã ra đời và thu hút nhiều khách hàng. Đầu tiên để kinh doanh thì bất kì mặt hàng nào chúng ta cần có nguồn vốn ổn định và đồ chơi trẻ em thì cũng không ngoại lệ. Nếu bạn cảm thấy thiếu vốn thì có thể Vay tin chap tại các ngân hàng, lãi suất cũng rất thấp. Bạn phải dự tr…

Hi, I want to attach an external USB-I2C adapter (i2c-tiny-usb, https://github.com/harbaum/I2C-Tiny-USB). As I understand, the existing kernel drivers should be invoked for this. First I tried with Raspian, all went fine: [ 66.451429] usb 1-1.3: new low-speed USB device number 7 using dwc_otg [ 66.595547] usb 1-1.3: New USB device found, idVendor=0403, idProduct=c631 [ 66.595562] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 66.595571] usb 1-1.3: Product: i2c-tiny-usb [ 66.595579] usb 1-1.3: Manufacturer: Till Harbaum [ 66.595587] usb 1-1.3: SerialNumber: 0150 [ 66.633027] i2c-tiny-usb 1-1.3:1.0: version 2.01…

I have a local OpenVPN server on Banan Pi M1, with latest armbian. I tried to replace with OrangePi3 but current results is disappointing iperf3 results on Banana Pi M1 OpenVPN server Connecting to host bouygues.iperf.fr, port 5201 [ 4] local 10.8.0.4 port 46250 connected to 89.84.1.222 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 1.69 MBytes 14.1 Mbits/sec [ 4] 1.00-2.00 sec 1.81 MBytes 15.1 Mbits/sec [ 4] 2.00-3.00 sec 2.43 MBytes 20.4 Mbits/sec [ 4] 3.00-4.00 sec 681 KBytes 5.58 Mbits/sec [ 4] 4.00-5…

Hello folks! I'm investigating an odd issue of the OPi R1 board, with the image Armbian_5.83_Orangepi-r1_Debian_stretch_next_4.19.38. With this version of software the board works fine, but apparently the wifi cannot reconnect after a disconnection (error: association request to the driver failed) The only workaround I found is to manually bring down the wifi interface and then back up; then the reconnect is almost immediate. I tried to disable the NetworkManager and now I'm using /etc/network/interfaces file to handle the connections but the problem still persists. I checked the issue with another R1 board and so I can exclude that the boa…

Hi, I did a dist-upgrade on my BPi M1. Now it is running on ARMBIAN 5.73 stable Debian GNU/Linux 9 (stretch) 4.7.3-sunxi When I choose a newer kernel in armbian-config after the reboot it is still running with the old kernel. When I do an apt-get upgrade it shows this error in the output: update-initramfs: failed for /boot/initrd.img-4.20.7-sunxi with 1 The BPi is booting from SSD with LVM. Thank you very much for any help. Regards, Robert

I would like to add the Orange Pi Lite 2 into the discussion of boards to support. Info from Orange Pi site - http://www.orangepi.org/Orange Pi Lite 2/ Hardware specification CPU H6 Quad-core 64-bit ARM Cortex™-A53 GPU • High-performance multi-core GPU Mali T720 • OpenGL ES3.1/3.0/2.0/1.1 • Microsoft DirectX 11 FL9_3 • ASTC(Adaptive Scalable Texture Compression) • Floating point operation greater than 70 GFLOPS Memory (SDRAM) 1GB LPDDR3 (shared with GPU) Onboard Storage TF card (Max. 32GB) /MMC card slot WIFI+BT AP6255, IEEE 802.11 AC/bb/g/n, BT4.1 Audio Input MIC Aud…

I am compiling the armbian for orangePi3, using the armbian tools ... and the compilation works fine. It works both from the kernel_only and from the entire image But I have a problem with the current version of the kernel, because it turns out that it does not support the hdmi-vga adapter and I would like to compile the 5.07 kernel instead of the 5.10. I have found in the doc but I do not find how to indicate to the compile.sh script that it has to compile version 5.07 of the kernel. Inside the file config-default.conf I do not see where to put the version. The documentation: https://docs.armbian.com/Developer-Guide_Build-Preparation/ It is insuffic…

There are two USB dongles on my Orange Pi One box, one is a USB Bluetooth in USB-OTG port and other is a mu7601 USB WiFi in the USB port. When I switched it from legacy kernel to lastest development kernel 4.11.x, the bluetooth card disappeared. So I exchange two dongles each other , the one in USB port works, and the one in USB-OTG port always failed. Is there any solution?

I am not experienced on the Linux networking so please tolerate my ignorance. 1.) I am trying to create an wireless access point on "Orange Pi Zero Plus 2 H3" board. And I fail... 2.) I am using Armbian image: Armbian_5.76_Orangepizeroplus2-h3_Ubuntu_xenial_next_4.19.21.img 3.) I am using nmcli for this purpose: https://gist.github.com/narate/d3f001c97e1c981a59f94cd76f041140 nmcli con add type wifi ifname wlan0 con-name MyAccessPoint autoconnect yes ssid MyAccessPoint nmcli con modify MyAccessPoint 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared nmcli con modify MyAccessPoint wifi-sec.key-mgmt wpa-psk nmcli con modify MyAc…

Hello friends; I have board which Orange Pi Win Plus running Armbian. My problem is, boards 7, 8, 10 and 16 physical pins are not working. When I tried to I/O with this pins, console says: Segmentation Error. Is it possible to fix it or is it normal? Thank You.

I use a NEO2 (H5), with armbian linux 4.19.13-sunxi64, and have a StarTech usb2.0 to Gigabit-ethernet adapter, which I plug in the usb slot of the NEO2 and which gives me a new additional ethernet interface. iperf3 on this interface (against another NEO2 with its generic gigabit interface) gives maximum 111 MBit/sec, even with the tips in https://forum.armbian.com/topic/7001-slow-usb-speed-on-h5-devices-orangepi-prime-probably-cpu-governor-related/ (which actually dont change much) Using a raspberry pi (2B) with the same adapter and cable I get 170 MBit/sec, which is significantly more (although still not what one should hope for, which is up to 30…

So I did the following today: Spoiler sed -i /deb/s/jessie/stretch/g /etc/apt/sources.list $ sed -i /deb/s/jessie/stretch/g /etc/apt/sources.list.d/*.list apt-get update apt-get upgrade apt-get dist-upgrade Everything went fine except at the end where it complained about busybox not being there and it failed the update of initramfs... This was no issue. I installed busybox, rebooted, ran apt-get autoremove and then autoclean and everything worked fine. I was still on kernel 3.x, so I ran armbian-config but I did not see the latest kernel present in the switch kernel option. I ran apt-get install linux-image.next.sunxi (or some…

I would like to connect reed switch to OrangePi Zero with H2 processor. Can I use this? https://github.com/duxingkei33/orangepi_PC_gpio_pyH3 Under examples, there are two examples I think I could use: - read_button.py - read_key_PG7.py I have two questions. 1. Where is the pinout? read_button.py has this code: led = connector.gpio0p0 # This is the same as port.PH2 button = connector.gpio3p40 read_key_PG7.py has this code: led = connector.gpio1p38 # This is the same as port.PH2 button = connector.gpio1p40 #CHOW Which pins are which, where to get the picture of GPIO pins? (And why LED's…

Hi guys, I've been having problems on my NanoPi Duo implementing a music streaming service using Alsa PCM to output the audio. When calling snd_pcm_open with the nonblock flag set, I had snd_pcm_writei returning a broken pipe error several times per day (when continuously playing). I noticed not setting this flag and, thus, allowing snd_pcm_writei to block until there was enough room in the Alsa PCM buffer, did not show this problem. This was however unusable because the blocking behaviour slowed down the rest of the software enough to be annoying. I think I solved it now by checking with snd_pcm_avail_update if there's enough room available, …

Hello, I recently installed Armbian 5.85 legacy on my new Orange Pi Lite in order to try out my new Orange Pi camera, but it's not being recognized at all, even after following the instructions in this topic: I already tried doing the following (as root) unsuccessfully (no errors returned, but still can't detect camera): sunxi-pio -m "PG11<1><0><1><1>" #DOVDD sunxi-pio -m "PE15<1><0><1><0>" #Power_Down sunxi-pio -m "PE14<1><0><1><1>" #reset modprobe gc2035 modprobe vfe_v4l2 Here's the output of lsusb: Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001…

Hi, I try to connect Orangepi lite to SIM800l module. I don't have any response on AT commands. I checked the module with Arduino and it works. So I connected Arduino and Orangepi and I can send messages from Arduino to Orangepi, but I can't get any message from Orangepi to Arduino. 1, On Orangepi I allowed UART3 via editing /boot/script.bin [uart3] uart_used = 1 uart_port = 3 uart_type = 4 uart_tx = port:PA13<3><1><default><default> uart_rx = port:PA14<3><1><default><default> uart_rts = port:PA15<3><1><default><default> uart_cts = port:PA16<3><1><default><defau…

Hello... I've got an Orange Pi Zero Plus 2 H3 with Armbian Stretch. Kernel: 4.14.70-sunxi armbianEnv.txt: I did: cp -a /lib/firmware/ap6212/fw_bcm43438a1.bin /lib/firmware/brcm/brcmfmac43430-sdio.bin dmesg when searching for "brcm" gives me: [ 8.123186] brcmfmac: brcmf_fw_map_chip_to_name: using brcm/brcmfmac43430-sdio.bin for chip 0x00a9a6(43430) rev 0x000001 [ 8.256708] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Oct 8 2016 15:31:47 version 7.46.57.4.ap.r4 (A1 Station/P2P) FWID 01-3621395e es6.c5.n4.a3 In /etc/default/ap6212 I have: PORT=ttyS1 But the scr…

Hey there, I just build a fresh dev image for the OrangePi One Plus (Stretch, console only, 5.0.x megous sources, latest commit was https://github.com/armbian/build/commit/783c2d0e25ff4542876943cfef6a7ac2921d1262) and unfortunately it seems to be unbootable. I put verbosity to 7 to get some more information rather than being stuck at "Starting kernel..." and this is what came up: Spoiler U-Boot SPL 2019.01-armbian (May 02 2019 - 13:14:43 +0200) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.1(debug):9a25f98-dirty NOTICE: BL31: Built : 13:14:40, May 2 2019 NOTICE: BL31: Detected Allwinner H6 SoC (1728) NOTICE: B…

Hello everyone :-). I would like help, I checked on the Web and I found using the forum a script (that I modified) to trigger using DTS LEDs. I adapted the script found here at the end of the page: Topic 112-dtb-howto-add-leds I think that for the section "disk-activity" and "netdev" it misses options but I'm not a developer just a scheming. Can you please explain to me how to add options to the mentioned trigger? I searched a lot of time but did not find any information. Here is my script, everything works fine (compiled with armbian-add-overlay), but "disk-activity" and "netdev" do not work. I tested the write / read trigger on disk but did no…

Dear colleagues, good afternoon. I have 3 problems with the display. I have a orange pi zero. Installed armbian. I set the 2.8-inch display ili9341 spi for instructions, all works very well, but ... expansion of the display - 320x240. But the system is set up as 640x480. Font on the console - Terminus framebufer 6x12. And I am looking for a smaller. Help me please. I want to make the setting expand in the system - 320x240. Font still less. And it passes the wrong color, and I want to make the right color.

Hi ,,I'm a new user,,,,,OP Zero , I have this mess in the armbianEnv.txt , but i didn't edit it ssh-ed25519 AAAAC3NzaC1lZDI1NTE5AAAAIDb34fWZZQ2gTi9CuFLQbQ0S3dRH48ZKkzjv6xZ6lFs$ ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^$ usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Is correct? How is the default file? Can someone gime the correct? Thanks

Hello, do you guys havea proper device configuration file for crosscompiling Qt apps to Armbian on my opi one? Couldn't find one online and the multitude of flags frankly confuse the heck out of me.

Hello, I am trying to apply the following configuration to my nanoPi Duo Core: * Boot from eMMC * System on SATA/USB (disk) When i try to find the eMMC device using the command "fdisk", I can only see the SD card and the disk that I added. My NanoPi duo core contains the eMMC memory but I am unable to find it. In addition to that, If I try to execute the script "nand-sata-install", only one option is available : boot from SD, system on SATA / USB. The other two options : "boot from eMMC / NAND, system on eMMC/NAND" and " boot from eMMC / NAND, system on SATA / USB" are not mentionned. Can someone help me w…

Hi guys, i dont'understand well mali driver status. Someone can explain me if a working driver exist? And if exist what is best method for build a functional driver? Ive read someting about full mali ddk source that require a license but is not clear if opensouce driver is equivalent or has limitation. I have found: https://developer.arm.com/tools-and-software/graphics-and-gaming/mali-drivers/midgard-kernel If i build this there is some hope to having some kind of accelleration for a normal desktop life like showing wideo with high framerate, Youtube, etc? Thanks in advice Orangepi3 nigtly.

Hi, I have an Armbian image that uses the DTB for the Banana Pi R1 aka Lamobo R1 device. That same image boots fine also on a Banana Pi M1 device, but still needs the DTB be switched to the M1 device. On the online help page https://docs.armbian.com/known_issues/cubox/ it is written that one can do such a DTB-switching with the armbian-config tool: "use armbian-config to select proper DTB for your board (armbian-config -> system -> DTB)" BUT: there is no "system" entry in my version of armbian-config: Armbian 5.31 stable Debian 8.11 configuration utility, http://www.armbian.com And the login message says: Welcome to ARM…

Hi, Perhaps it is documented elsewhere but I could not find a direct solution after googling few minutes. My u-boot partition was stuck at the same version on the nightly. I needed to fix the reboot issue. I've tried few things like apt upgrade or direct dpkg -i... Anyway, this is what I did on a EMMC installation (/dev/mmcblk2) after I've built and download my own version of the package: dpkg -i ./linux-u-boot-dev-orangepi3_5.86_arm64.deb cd /usr/lib/linux-u-boot-dev-orangepi3_5.86_arm64 cat sunxi-spl.bin u-boot.itb > u-boot-sunxi-with-spl.bin dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2 bs=1024 seek=8 reboot I'm my case I had to u…

Hi I own since a while an Orange Pi One Plus board that I have been unable to use till now (OS images supplied by manufacturer are just a joke !). I wanted to give it a test with ARMBian as you offer now some Beta images. As both Bionic and Stretcher are offered, is there one of them more stable or more near something finished ? Did someone have tried the board with one of these ? and did it work ? Thanks Vincèn

Hi, I'm back to China and got the NEWEST Orange Pi 3 at hand. But, it looks this new SBC has NOT been supported yet (please refer to https://www.armbian.com/download/?tx_maker=xunlong) ? Just expecting when will the armbian support for Orange Pi 3 out? Cheers Pei

Hello guys, I configured bridge via nmcli/nmtui br0. Slave devices of bridge are eth0 and wlan0(as wifi access point). OS: Armbian_5.59_Orangepizero_Ubuntu_xenial_default_3.4.113 root@orion2:~# nmcli c s NAME UUID TYPE DEVICE bridge-br0 fff57bce-6051-458d-9394-7101741af59f bridge br0 bridge-slave-eth0 25720542-2bdd-498e-992e-4415385673d5 802-3-ethernet eth0 bridge-slave-wlan0 ed8b07bf-a793-4717-8c99-2e84d54af672 802-11-wireless wlan0 Configuration looks fine, but when I try login to AP, my smart phone shows error message: "Authentication issue" , an…

U-Boot SPL 2018.11-armbian (Feb 08 2019 - 08:51:22 +0100) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2018.11-armbian (Feb 08 2019 - 08:51:22 +0100) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: LeMaker Banana Pi I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 Loading Environment from EXT4... ** File not found /boot/boot.env ** ** Unable to read "/boot/boot.env" from mmc0:1 ** Setting up a 720x576i composite-pal console (overscan 32x20) In: serial Out: vga Err: vga SCSI: SATA link 0 timeout. AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part ccc apst …

Hello, i'M having this issue with the latest Armbian 5.75 stretch image with updated firmware. When booting with a huwei E303 modem is in the usb port the board fall in a eternal reboot. if i let the board boot as normal an then insert the modem everything is o.k. I tried with 4 others OPI PC+ and others E303 sticks, same thing. also tried with 5.65, same problem. BUT, with an earlier version 5.35 and it boots as normal.

Recently I borrowed my Orange Pi PC2 to a friend, and he fails to set up SSH connection w/ it. After debugging w/ HDMI monitor, I found ssh_host_ecdsa_key, ssh_host_ed25519_key and ssh_host_rsa_key are preloaded to the Orange Pi PC2 image, which prevented SSH from working. Even if it doesn't prevent working of SSHD, it's also a severe security hole -- that means all Armbian installation with the same image will uses the same host key and they're vulnerable to MITM attack. I think these files should be purged when generating image, and regenerated when first powerup. It's what AOSC OS images do.

Hi, I have some armbian 5.38 (kernel 4.11.5) installations and recently updated them. With this update I got kernel 4.14.18. When I executed command "armbianmonitor -m" I used to get something like this: :~# armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU PMIC 10:52:13: 528MHz 0.35 21% 2% 18% 0% 0% 0% 40.8°C 41.0°C 10:52:18: 528MHz 0.52 21% 2% 18% 0% 0% 0% 40.7°C 41.0°C 10:52:24: 528MHz 0.47 21% 2% 18% 0% 0% 0% 40.7°C 41.0°C Now after update, and kernel 4.14.18 among other new packets, I got this: …

Hi, Sorry, I don't know if correct topic, but I have a Orange PI 3 and have problem with DNS resolution. I tried with image Armbian_5.82.19042 based in Debian and Ubuntu but is imposible make to work. I added the line net.ipv6.conf.all.disable_ipv6=1 in /etc/sysctl.conf file but this change not resolved the problem. For example if I try to ping www.google.com sometime take a 25 second for DNS resolve to IP address. I don't see any problem with my local network because I have other devices that not have any problem with DNS resolution. Please, your help.

After upgrade to latest kernel (4.19.38) my device only boots into maintenance mode. System is on emmc and no problems before. I started armbian-config and switched back to previous kernel, but it doesn't boot system. Even with all USB devices disconnected it didn't start (as i see there are some usb errors in log), file system seems to be clean, just didn't start system in normal mode.... Any advice? Thx Update: OK, solved, after installing latest updates within maintenance mode its ok again....

Hello, i had a problem withe an Orange Pi Lite and the Cheap RPI Display. The Display Backlight is on. I had used this tut: https://forum.armbian.com/topic/6737-orange-pi-zero-35-tft-touchscreen/ https://forum.armbian.com/topic/4837-guide-how-to-use-touchscreen-lcd-on-h3-devices/ --- 2) Create a makefile (Take note that it is TABS instead of spaces before the $(MAKE)) nano Makefile Insert the below in without the ----- -------------------------------- obj-m := ads7846.o KDIR := /lib/modules/$(shell uname -r)/build PWD := $(shell pwd) all: $(MAKE) -C $(KDIR) M=$(PWD) modules clean: $(MAKE) -C $(KDIR) M=$(P…

Hi, I am using Linux nanopiair 3.4.113-sun8i distribution on my Nano Pi Neo Air and trying to get the g_ether works. After using modprobe g_ether and set up the network/interfaces auto usb0 iface usb0 inet static address 192.168.0.2 netmask 255.255.255.0 then edit /etc/modprobe.d/g_ether.conf: options g_ether host_addr= 06:7b:95:4c:59:d7 After reboot it shows: [ 6.868451] usb0: MAC 06:7b:95:4c:59:d7 [ 6.868475] usb0: HOST MAC 5e:5b:65:8f:94:85 [ 11.484526] systemd[1]: Found device /sys/subsystem/net/devices/usb0. [ 16.249726] ADDRCONF(NETDEV_UP): usb0: link is…

I am having problems with the NanoPi R1. I loaded the latest Armbian for R1 on flash. All works good. I went to armbian-config to load into eMMC. The last step of the process had weird text on the dialog, I clicked "OK" anyway, and the process seemed to be working. But after removing uSD card and rebooting, the board does not work. The red led stays on solid. Did anyone successfully burn the image from uSD to eMMC using the tool in armbian-config?

Hi, I guess this question depends on knowing the OPi Lite hardware reset button capabilities before being able to answer the following question. but here goes: Does anyone know if the OPi Lite button can be scripted/coded to not only execute a shutdown or reboot command but to do both? So, say, a single short press would gracefully reboot the OS while a long press (hold for, say, 4 seconds) would perform a shutdown? Thanks!