Allwinner sunxi

I started first with orangepi pc2 (H5) but now trying the same thing on orangepi one (h3) - trying to make ili9340 module work it works flawlesly on rpi with raspbian so the hw module works (and the fb_ili9340 module in kernel talks to it properly) debug info I pulled from rpi pi@octopi:~ $ uname -a Linux octopi 4.14.79-v7+ #1159 SMP Sun Nov 4 17:50:20 GMT 2018 armv7l GNU/Linux root@octopi:~# lsmod Module Size Used by xt_tcpudp 16384 1 iptable_mangle 16384 1 xt_DSCP 16384 1 bnep 20480 2 hci_uart 36864 1 btbcm 16384 1 hc…

Is there a plan for supporting the "NanoPi Duo2" from"friendlyarm" in the future? http://wiki.friendlyarm.com/wiki/index.php/NanoPi_Duo2

Armbian Legacy 5.56 Kernel 3.10 boots and installs to the eMMC (as long as ext2fs is picked). Armbian Dev 5.56 Kernel 4.19 does not boot from the SD Card at all (power LED and black screen). I don't have the serial console adapter (yet) so I don't know if there is something useful there.

Hello, No bluetooth device in my Armbian... Banana Pi M2+ ARMBIAN 5.65 stable Ubuntu 18.04.1 LTS 4.14.84-sunxi dpkg-query -Wf '${Version}\n' bluez 5.48-0ubuntu3.1 No Bluetooth device(hci0): rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Which refers to the error: systemctl status ap6212-bluetooth.service ● ap6212-bluetooth.service - LSB: Patch firmware for ap6212 adapter Loaded: loaded (/etc/init.d/ap6212-bluetooth; generated) Active: failed (Result: exit-code) since Tue 2019-01-08 09:18:38 UTC; 1min 2s ago Docs: man:systemd-sysv-ge…

I have 1 "Customised Olimex Lime A20 SBC with RTL-SDR chip installed in the board (AirNav XRANGE). Currently the OS I'm using is the Lime A20 Armbian Stretch 4.14.84, everything is works fine except for the 2 GPIO LED. I have no idea how to let it work. I have the edited "sun7i-a20-olinuxino-lime.dtb" from Armbian Jessie 4.11.5 which is mainly for the board. May I know is there a way to incorporated the "Armbian Jessie 4.11.5's sun7i-a20-olinuxino-lime.dtb into the A20 Armbian Stretch 4.14.84 so that the 2 LEDs will work again? The edited dtc for LEDs to work "sun7i-a20-olinuxino-lime.dtb" attached. Hope to get so…

Greetings all, See my last post in thread for method I found to get around issues. EDIT: This may be limited to is an apt issue DNS seems ok after all. Use nmtui to edit network config not armbian-config None of what follows should be taken as complaining. I am only trying to get some help, give some observations from a non-expert viewpoint and possibly help ID a bug. Not being an expert, I am looking for confirmation. I am trying to get the NanoPi NEO core-2 LTS set up and am having some issues with apt. I haven't gone past that because the first thing after getting properly booting install (for me anyway) is to install webmin…

hello dear all, good day dear Armbian-experts recently i have managed to get Armbian up and running on a Banana Pi. I was very very glad. now i am digging deeper into the system and try to learn all the necessary things. regarding another system: on orange pi -pc i want to install armbian - from this page https://www.armbian.com/orange-pi-pc/ i fetch Armbian Stretch mainline kernel 4.14.y Server or light desktop usage scenarios. Stable question: can i upgrade after the installation the system to the newest kernel... ?!? Is this possible?

Hello dear commnuity have installed armbian banana pi m2 kernel 4.19 on a BPI How to get the graphical configuration screen!?

For days now I have been fighting to get this thing working. No boot, No hdmi, no sound, no wireless network and so on. Armbian is anyway the best choice for this device, Supported? well yes if you have lan, true HDMI Well i got it to boot, after writing a new image to sd card. finally booted, no signal detected ( with a DVI > HDMI ), I had to hook it up to a true HDMI and modify the script.bin file to get a signal. Got it to boot all the way to the desktop. Hurray ! Plugged in a crappy wifi adapter from Ali express (realtek 8081 i think it is) and I got wifi, jippi. Next time booting no wifi, no matter what I tried. Made a new image again, with modi…

I'm running an updated armbian stretch mainline on a nanopi neo and hitting a wall where I thought there would be no obstacles in my path. I'm using 433Mhx Tx and Rx devices so I'm building WiringNP (from FriendlyArm) and rfoutlet (from github.com/timleland/rfoutlet.git). I'm getting errors such as wiringPi ISR: Not implemented when running RFSniffer. [This is the current error, it's been one after another]. My mind is muddled at the moment since I've done this kind of thing several times in the past on other devices including the Orange Pi Zero. Can someone tell me if this is me, or if it's a NanoPi Neo-thing? Shouldn't this be straight-forwa…

Working from the documentation here: https://docs.armbian.com/Developer-Guide_FEL-boot/#what-is-felnfs-boot. Not much luck so far with an FA NanoPi K1 Plus. Please see below for details. TIA.

hi all i'm trying to boot my orange pi over the network. i have written u-boot into SPI-Flash memory. i modified boot.cmd script to download the kernel, init ram and script.bin from TFTP server. after downloading them all the kernel tries to start but it dose not proceed. I've attached the screenshot of the console. My boot.cmd Spoiler # DO NOT EDIT THIS FILE # # Please edit /boot/armbianEnv.txt to set supported parameters # setenv serverip 172.20.20.200 setenv load_addr "0x44000000" setenv overlay_error "false" # default values setenv rootdev "/dev/nfs" setenv verbosity "1" setenv console "both" setenv disp_mem_reser…

Hi all, i am completely new to armbian and to be honest not yet completely convinced to change from bananian even that the time should have come. Until now, on my Bananapi M1, bananian was running without any problems. A few days ago, i tried to get familiar to armbian (debian stretch) for the first time on a test-SD-card. Now my problem: Since these tests, i am not able anymore to shutdown my running bananian-system to power off. The system seems to halt, but the power is not turned off and a few seconds later the Bananapi restarts. The problem remains even on a clear bananian1604-image. But: On the testSD-card under armbian the shutdown comm…

Dear experts, I would like to make my OrangePi PC on board LEDs works like power (Green: Default ON) and status (Red:heartbeat blinking). root@orangepipc:~# ls -1 /sys/class/leds/ orangepi:green:pwr orangepi:red:status root@orangepipc:~# Any experts can assist me on this matter on edit in /etc/rc.local to get it works. Thanks in advance and appreciated your help. Regards, Sai Hou

I installed ARMBIAN in a cubieboard2, then i insert a microSD card with 3 partitions and 1 of them cant be accesed directly from desktop... i receive the msg PERMISION DENIED. please i need help in that partition there is a program that i need to transfer to ARMBIAN to make my ARMIGA SYSTEM live again. How can i access it ?

Preamble: I have done numerous hours of reading and searching (due diligence). See end. I have a FA NanoPi NEO Core-2 LTS with shield and 64G M.2 (This shield uses JMS567-LGBB1A chip USB to sata for M.2 access). I have successfully installed Armbian from SD to and booted from the eMMC. Armbian Stretch mainline kernel 4.14.y - This image https://dl.armbian.com/nanopineocore2/Debian_stretch_next.7z armbianmonitor -u results http://ix.io/1xAA Logs indicate formatting did occur correctly as far as I can tell. The volumes are formatted as I selected - along with an 'extra' ext4 volume that looks like it is just for boot. NOTE: Since…

I had an annoying issue with the WiFi of this board with Armbian 5.65 Ubuntu and Stretch. Sometimes it would spontaneous lose its WiFi connection. After researching it for a while I noticed that the wlan0 interface sometimes lost it's IP address. At first I thought it had something to do with the DHCP lease or sleep mode of the adapter. I just couldn't get my head around it and I ended up removing network-manager and going back to creating an interfaces.conf file for setting up my network interfaces. Somehow this solved the issue, the WiFi connection hasn't failed since! To do this, first create the wpa supplicant configuration file: ~# …

trying to get ili9340 to work on orangepi pc2 on bionic 4.14.91 ... there's a fb_ili9340 module in the staging directory, modprobe passes and the only thing in dmesg is warning it's staging nothing else but when I check /dev/fb* there's only /dev/fb0 (the original hdmi output on my monitor), there's no /dev/fb1 anyone can land a hand? give a hint?

hello, i am setting up Mopidy in Orange Pi PC2 with armbian. but i found it only playback to the on-board sound card not the USB DAC i connected. root@orangepipc2:/# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: allwinnerhdmi [allwinner,hdmi], device 0: 1c22800.i2s-i2s-hifi i2s-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 2: Audio [iFi (by AMR) HD USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 i found there is no asound.conf in /etc ... …

Hi all, I've come upon a weird thing and I wanted to verify that I don't so something wrong. I've build a custom kernel module which is a PWM led device with an SPI interface. If I use the spidev, then everything works fine and I'm able to control the led. But when I'm using a custom device-tree and load the module then when I'm calling the `spi_write()` function then I'm getting an error (-22). The external device is actually an arduino nano that implements an I2C IIO light measurement device, using a dual light dependent resistor. Also I'm using the SPI channel to drive a led using PWM. It's very straight-forward a…

Hello Maybe it will help someone. I lost a lot of time trying to connect 1-wire to Cubieboard2 via DVK 522 (it has DS18B20 connection on PB10 /gpio 66/ with external pullup). I've done steps in http://linux-sunxi.org/1-Wire with different combination and it doesn't work. In /sys/bus/w1/devices i had only sth like 00-80... 00-40... 00-c00.. without w1_slave file (i was 100% sure of hardware - it works on waveshare debian image) SOLUTION: In /boot/armbianEnv.txt lines needs to be without comments: and that's it ( overlays are created automatically by config so it will be sth like for…

Hello All, I have configured OrangePiR1 as router. There are three network interfaces, two as wired and one wifi(hotspot). eth0 serve for access to internet(via ppp/adsl) and eth1+Wlan0 for internal network. Interfaces eth1 and wlan0 are in bridge br0. Problem is, that interface eth1 sometimes loses connection/link(cable and switch were checked ). Next nonstandard behavior of eth1 is, that only yellow led control is blinking, while green led control is not alight. Network interfaces were configured via file /etc/network/interfaces. However, when I checked network manager nmcli, I saw, that some connections are configured there too (there can …

Hello. Armbian_5.35_Orangepizero_Ubuntu_xenial_default_3.4.113.7z Orange Pi Zero 256 I am rading the bootlog via serial console. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. # systemctl status systemd-modules-load.service â systemd-modules-load.service - Load Kernel Modules Loaded: loaded (/lib/systemd/system/systemd-modules-load.service; static; vendor preset: enabled) Drop-In: /lib/systemd/system/systemd-modules-load.service.d ââ10-timeout.conf Active: failed (Result: exit-code) since Sun 2018-12-30 00:20:40 CET; 3min 8s ago Docs:…

Hi, my Banana Pi M2+ with Armbian Bionic doesn't see my access point on channel 13. I already set "REGDOMAIN=DE" in /etc/default/crda and also issued the command "iw reg set DE". "nmcli dev wifi list" shows a lot of other access points on channels 1, 6, 11, but not my own on channel 13. On the other hand, "iw list" shows: Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) …

I had it and lost it: u-boot with I2C. I did not write down how I did it (was heavy) Tried to build yourself again: does not work. u-boot-mizi.bin does not want to boot. For 2 days I try to find the solution. Google has already blocked me Can somebody help? I need i2c directly, after power on, to read FRAM and set relays. Programming in Linux is enjoyable but system administration is horrible. Thanks

Hello, I can't boot my new OrangePi One v.1.1. I have used various SD cards including Sandisk Ultra 32GB. On the serial console I every time see: U-Boot SPL 2018.05-armbian (Oct 26 2018 - 22:09:12 +0200) DRAM: 512 MiB Trying to boot from MMC1 MMC Device 0 not found spl: could not find mmc device. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### Power supply is 5V 3A. Ethernet is unplugged and nothing is connected to USB. What I tried: - Flashed on two different computers (MAC and Windows) - used both etcher and dd - checked cards with h2testw for errors (…

I am lost, the soundcard used to work when I first started with this board but now I get a "aplay: device_list:270: no soundcards found..." error. When I tried to enable the analog codec using armbian-config I get an empty screen. This also used to work the first time. So I created a new SD card using Armbian Stretch this time but with exactly the same result. I am desperate! The diagnostic output is here http://ix.io/1x25 Kind regards, Hans C

I am trying to set up a Orange Pi Zero to use as a small NAT/ Bridge Device. I want to use an Android phone in USB tether mode to give its 4g connection to an interface on the opi zero then use a network bridge to join the 4g connection to the lan port, also the opi zero is gonna run a small section of code on the USB interface that changes the TTL of all packets through the interface. On my linux mint box the script looks like pkexec sysctl net.ipv4.ip_default_ttl=65 && echo 65 | pkexec tee /proc/sys/net/ipv4/ip_default_ttl but i am running into issues with the very first part, that is getting my phone native USB tether to be recognized as an interface in …

Is there a way to run netflix yet? Does Chromium run well and able to run netflix? Appears this doesn't matter, because Chromium doesn't work with netflix anymore... Does anyone know if chromium OS works well with OPi PC otherwise? Basically I want it to work for netflix, I also want to connect it to a printer, and the ability to run NordVPN and a torrent client would be a bonus as well.

Is the build for Orangepi Plus the same for Orangepi Plus 2? When I download for OPI Plus 2 I get the following file: Armbian_5.65_Orangepiplus_Debian_stretch_next_4.14.78 but it will not start

Hi everyone. I have a opz with H2+ and expansión board. I had installed Jessie before. And now, I upgraded to stretch. why espeak-ng sounds so bad?? in jessie that did not happen.

Hello guys, soon I will receive this nice toy (512MB) and I want to be prepared for my project: a domestic vpn server (using pptp) serving 1 o 2 guests at most. For this project I just need the RJ45 socket thus I would like to switch off as much as possible (e.g. GPU, on board wifi and others if there). Someone can point me to some resources or list what I can do to accomplish this? P.S. I know that pptp is not as secure as IPSec (and maybe IPSec is heavier for such device) but for the purpose of my project it is enough. Thanks a lot Gianni

Hi All, I am working on project using Qt(IDE), C++(language) and opencv libraries. The board I am using is Olimex Olinux A64. In the project I have a GUI that displays the input from a camera and has various status indicator labels. These labels indicate various states the system is in at any particular instance of time. I load different images in the labels to indicate different states. As of now the trigger to change the image of a label comes from soft buttons written in c++ using the Qt buttons layout. I am trying to find a way to control the change of images in the labels using hardware buttons that are connected to the GPIOs of the A64 board. Cou…

Hi all! I have an Olimex Olinuxino-Lime2-4GB A10 cpu based dev board and I have installed Armbian on an SD card. Everything works fine, except when trying to compile some drivers for the wifi dongle that I want to use. The dongle has an RTL8188CUS chip, and I also have another dongle with an RTL8192CU chip, and when following the instructions found here the compilation fails, because of the kernel headers missing. The instructions work fine on other distributions. Could someone help me figure out how to successfully compile the drivers? Where can I get the kernel headers? I really need these drivers for my project.

Hello I have desktop version and I can`t on the AV sound card. The sound works on HDMI. Could You advice how to do it? I`m try to this solution but sound card is still not available. alsamixer is diffren

I found the way to install, keep updated and easily uninstall plexmediaserver without using armbian-config. here is the link https://forums.plex.tv/t/read-me-first-about-server-armhf-arm64-debian-ubuntu-raspberry-pi/226567. I used the version arm64 / ARMv8 and on OPzeroplus with H5 works very well. Spoiler arm64 / ARMv8 # become root sudo su # add my public key wget -O - https://dev2day.de/pms/dev2day-pms.gpg.key | apt-key add - # add my PMS repo echo "deb [arch=armhf] https://dev2day.de/pms/ stretch main" >> /etc/apt/sources.list.d/pms.list # activate https apt-get insta…

Hi, I'm using fbtft with legacy kernel in orange pi zero to be able to use 3.5 inch raspberry LCD with ILI9486 (not sure). Everything works and I can get image from the LCD (although it is terribly slow). But I have one big problem. LCD freezes after some time or when screen screen changes or even sometimes during initialization . Is there anything wrong with the spi driver in armbian ? How can I get over this issue ? I'm sure there is nothing wrong with the lcd because I have tested same lcd on raspberry pi and I have about 500 of these lcds for a project. This is the my fbtft options : modprobe fbtft_device custom name=fb_ili9486 gpios=dc:18,reset:2 busnu…

The orange pi zero has a USB OTG interface, which can be used to interact with it in the absence of networks and spare USB-UART converters. This is not enabled by default in the Armbian image. Here I describe how to modify the system image before first boot to enable this. First, mount the freshly written SD card on a linux computer, become root, and change directory to the mount point, that is, the root directory of the SD card. The following couple of steps were taken from https://oshlab.com/enable-g_serial-usb-otg-console-orange-pi-armbian/which describes how to enable this in a live system, i.e. after first boot. The steps are modified to work on the moun…

hello i just install the latest armbian on orange pi pc2 board, the kernal is already 4.14 therefore the OTG function should be there. root@orangepipc2:~# dmesg |grep musb [ 1.323924] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 1.323939] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 9 [ 1.324416] usb usb9: Manufacturer: Linux 4.14.78-sunxi64 musb-hcd [ 1.324421] usb usb9: SerialNumber: musb-hdrc.1.auto however, i cannot enable the usb serial over OTG. anyone can show me how to do it? i tried it on debian and windows but both has nothing when i connect to the OTG port. thanks very mu…

any setting to put opizero h2 in promiscuous mode to record wifi packets?

RT, i am trying to use git and aarch64 tools to compile a lastest u-boot by my own,but ,it failed. there're the steps i was doing: 1. downloads the latest u-boot source code from offical web: git clone git://git.denx.de/u-boot.git 2.downloads the ARM Trusted Firmware from offcial web: git clone https://github.com/ARM-software/arm-trusted-firmware 3.compile the ATF for BL31 by using this cmd: sudo make CROSS_COMPILE=aarch64-linux-gnu- PLAT=sun50i_h6 all and then move the BL31 file into the u-boot root fold. 4. compile the u-boot for H6 by using this cmd: sudo mak…

Because today I did get my Black-Friday NanoPi Neo2 LTS 1GB I swapped my old Neo2 against this new 1Gb LTS-version. After assembling the new LTS to the fresh heatsink I did a testdrive and all went fine (network etc). So I did try to put the faceplate back on the case but it doenst fit. At the time when I did buy the case there was also a faceplate for the normal H3 Neo delivered. So for the new LTS Neo2 I had to use the faceplate for the H3-Neo, because the new LTS Neo2 has the USB-Port aligned like the H3-Neo . The old Neo2 has his USB-Port (on the main Neo2-PCB) a bit shifted against the Network-port. Also the new LTS …

Latest doesn't seem to work at all, so something like 5.59 4.18.0-rc7-sunxi64 mentioned here https://github.com/armbian/testings would be ideal. Alternatively is there a way I can build old version myself? I ran ./compile docker BOARD=orangepilite2 BRANCH=dev but resulting image doesn't work also.

Good day! I connect the real time clock, made according to the instructions: RTC time is set I set the wrong time in the RTC, reboot. I look at the time in the system clock - at first not the right one, from the RTC, then they are synchronized and it becomes the right one. But in RTC, the new correct time is not recorded. What am I doing wrong? Or what else needs to be done?

Had orange pi pc, can I write armbian img file to USB and boot from USB directly? my two sd cards failed less than 2 years, so consider to use USB drive instead

Hi all, I'm puzzled how everybody is building clusters of cheap SBC's, but nobody is implementing HA, redundancy, resiliency, failover, etc. They're just SBC's networked together. The SBC's are underprovisioned for Ceph, so I think that even if a Ceph configuration was managed to be shoehorned in, it wouldn't perform well. I don't know if DRDB is an option. How are people actually doing implementing real clustering technology on Orange Pi, for example? I'm using OPi+2E. Kind regards, Andrew

Hello Could You advice how to steering my GPIO output I need set "+" for this 4 canal 31 33 35 37 I already have the connect but can`t fine tutorial on web how to do it.

Hi, I use orange pi pc plus with armbian bionic, firstly I use it with a SD card and the temperature its around 30 centigrade degrees, its ok. Then I use EMMC without SD card and the temperature increases to 51 degrees (I think it´s very high), they are some way to use EMMC without the board increases the temperature?? Best regards, Nelson

The translation was done by Google Hello friends, my hardware: Orangepi pc plus dac-pcm5102mk-i2s. 3.5 "touch display So far I have the system in eMMC (ARMBIAN 5.60 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i) and optionally on 16GB uSD card (ARMBIAN Debian GNU / Linux 8 (jessie) 3.4.113-sun8i). In both cases, an xfce desktop is installed. The setup of the DAC I have after the tutorial I2S on Orange Pi H3 by Da Alchemist, February 29, 2016 in both Debian 8 and Ubuntu 16.04. Works well. I installed the display after the hints from How to use Touchscreen + LCD on H3 devices by kutysam, July 31, 2017. It claps with the display of the desktop, but the touch …

I haven't had any luck getting the ov5640 camera module working with the nanopi air. I have compiled the latest dev version of bionic and enabled the ov5640 as a module in menuconfig. I currently cannot get it showing up under /dev/video* Any ideas?

terminal command to connect 1)wifi (using username and password). 2)hotspot os i am using is Armbian_5.65_Nanopiduo_Debian_stretch_next_4.14.78.

Hi there I have a banana pi M1 and I have installed Armbian on it. The HDMI output / Display work fine if I have HDMI connected to the HDMI port of BPi and monitor/tv is turned on before Armbian booting process starts. However if I don't have HDMI connected before boot process or Monitor/Tv is not turned on then I don't see the display if I connects the HDMI or turned on Monitor later. It is a problem for me because when I want to connect to display to already booted OS. Does anyone faced this behavior? Please advise.

Hi I try use Nokia 5110 with Orange pi zero. I found this library: https://github.com/rm-hull/luma.lcd and try to run it on my orange pi with this tutorial: http://codelectron.com/interface-nokia-5110-lcd-and-raspberry-pi-python/ so in python shell I add these: >>> from luma.core.interface.serial import spi >>> from luma.core.render import canvas >>> from luma.lcd.device import pcd8544, st7735, uc1701x >>> import OPi.GPIO as GPIO >>> from luma.lcd.aux import backlight but after add this line, I got many error that told me that library is used for Raspberry pi only: >>> serial = spi(p…

hi how can i enable the tv out in orange pi PC+, I need to do a kiosk mode thanks

Hello, I want to use Armbian on a Cubietruck with an Onyx Boox Max 2 ebook reader (HDMI port) as display. I tested Armbian Stretch mainline kernel 4.14.y and Armbian Xenial desktop legacy kernel 3.4.y. But with both systems I get a black screen. I use the serial console to access the cubietruck. When I plug in the HDMI cable I get following info on Armbian Xenial desktop legacy kernel 3.4.y: <6>EDID version: 1.3 <6>PCLK=125000000 X 2104 2244 2284 2384 Y 1560 1565 1570 1590 fr 32 NP <6>Using above mode as preferred EDID mode <6>PCLK=125000000 X 2104 2244 2284 2384 Y 1560 1565 1570 1590 fr 32 NP <4>Unimplemented SV…

I got following error after boot mainline: brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code (0x30 0x30) brcmfmac: brcmf_p2p_create_p2pdev_timeout occured brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-5 How to fix it?

Hello, I have owned the Orange Pi PC for quite a while now, but I have been unable to solve a problem. The problem is that I can never quite manage to get the GPU drivers to work perfectly. They will often crash when using certain software like Chromium. Here is what I have tried doing so far: - Build and install the helper modules (libdri2,libump) - Installing the sunxi-mali driver - Building the video driver (xf86-video-fbturbo) - Build glshim -- Doing the following does not seem to have an effect on glxgears -- - Update arm-linux-gnueabihf configuration <-- Doing this breaks certain applications and gam…

Hi! I've been using Armbian on my a20 olinuxino lime2 board without issues for over a year now. Yesterday i decided to reflash the installation image onto the SD board. I've tried to flash it to different SD cards using the same method (SD card formatter + etcher), all of them booted but the SSH server always refuses the connection. Are there any workarounds to this?

I wouldn't ask for help here if I could find enough information to solve my problem. My program takes user-space GPIO interrupts as signals. It depends on this feature and GPIO interrupts are not replaceable. Testing code is as follows (on Pin12/PA07/GPIO7) by using SysfsGPIO: echo 7 > /sys/class/gpio/export echo in > /sys/class/gpio/gpio7/direction echo falling > /sys/class/gpio/gpio7/edge Check if it works with command `cat /proc/interrupts`: watch -n3 "cat /proc/interrupts | grep sunxi_pio" After configuration, give GPIO7 a pulse by attaching it to 3V3. This method does works on Orange Pi 0+ H5 running Ar…

Hello. I added overlays=pwm to /boot/armbianEnv.txt and reboot system. $ cat /boot/armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=3d863bb3-b616-4229-94e7-8c92ac95501a rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u overlays=pwm Armbian can't boot-up. ** Unable to read "/boot/boot.env" from mmc0:1 ** Failed (-5) In: serial Out: serial Err: serial Net: phy interface0 eth0: ethernet@1c30000 230454 bytes read in 23 ms (9.6 MiB/s) starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 USB4: USB EHCI 1.00 USB5:…

Hello! In order to compile software on my Banana Pi running Armbian 5.27 Debian 8, I started off uncommenting the "# deb-src" lines in /etc/apt/sources.list and then ran apt-get update and apt-get upgrade. The start screen in the shell would then ask me to reboot as the kernel was updated. But after the reboot there was no AppleTalk anymore to serve my old devices. Compiling a newer Armbian with an up-to-date version of Debian is of no use to me as I run software (A2SERVER) that is incompatible with newer systems. So how can I upgrade my system without loosing AppleTalk (which I configured as a kernel module when compiling two years ago)? …

i'm using banana-pi-m2+ already enable i2s0 by changing dtb file in /boot/dtb and can see i2s module load but aplay -l still not showing anybody help? root@bananapim2plus:~# lsmod Module Size Used by snd_soc_hdmi_codec 16384 0 dw_hdmi_i2s_audio 16384 0 sun8i_dw_hdmi 16384 0 dw_hdmi 28672 2 dw_hdmi_i2s_audio,sun8i_dw_hdmi cec 40960 2 dw_hdmi_cec,dw_hdmi sun8i_codec_analog 24576 1 sun4i_codec 32768 3 sun4i_i2s 16384 0 snd_soc_core 118784 4 sun4i_codec,sun4i_i2s,sun8i_codec_analog,snd_soc_hdmi_codec snd_pcm_dmae…

Hi Dear Friends! I'm having trouble using the onboard analog soundcard from my OrangePi Zero +. I already enabled analog-in in armbian-config, but when I try to run some application that uses the sound card, it has an error. In this example I'm trying to use the direwolf app that serves to decode FSK audio. The error also repeats when I try to use svxlink.

I have an Orange Pi PC Plus running the mainline Debian Stretch desktop version of Armbian, but lately I've been using it headless. When I'm logged in over ssh and shutdown it down using "sudo shutdown -h now", the ssh connection drops and the board's LED flashes then shuts off, giving every indication the board is off. However, power consumption doubles (increasing from ~1.2W to ~2.4 W)! The problem persists as long as the board is powered, so I presume the board is hung and never fully shutdown. Any thoughts as to what could be causing the board to hang when shutting down?

Hi to all, i´d try to setup a Banana PI M1 as AppleTalk Printserver because my old LaserWriter 4/600 only got a LocalTalk Interface. But the Kernel didn´t support AppleTalk, i compiled it in myself successfully. After i installed Netatalk 2.2.5 and do a nbplkup, the Bpi answers: bananapi:netatalk 65280.79:4 bananapi:Workstation 65280.79:4 No Printer, no Bridge. I think, the buildin Eth0 dont route AppleTalk Pakets. I tryed Bananian, armbian and strech without success. So, what shall i do? Hallmackenreuther

Hi, I am running a OrangePi One with Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Wed Jan 24 22:10:49 CET 2018 armv7l armv7l armv7l GNU/Linux DISTRIB_ID=Ubuntu DISTRIB_RELEASE=16.04 DISTRIB_CODENAME=xenial DISTRIB_DESCRIPTION="Ubuntu 16.04.3 LTS" And it seems that when I start the system without the hdmi cable and plug it afterwards, the HDMI is not handle correctly and my TV stays with a red screen. There is some way to configure the hdmi hot plug in this OS? I found that raspiberry pi has this option. (https://www.raspberrypi.org/documentation/configuration/config-txt/video.md)

Hi Everyone, I'm making a project about video and i want to export video to AV and HDMI without Desktop GUI. (i'm using armbian from https://dl.armbian.com/orangepizero/Ubuntu_xenial_default.7z). I reseached many documents, armbian-build resource, but i don't know how to make it! I have tried play video on Desktop GUI, it work fine! (mplayer, mpv) But without Desktop GUI, is it possible? Thanks!

Hello Community, Now I encountered the following problem when testing my "orange pi zero plus": I tested the processor load (stress-ng) at a working frequency of 624mhz for 25 minutes. Settings: mainline sunxi64-next (4.14.y) Spoiler armbianmonitor -m 10:53:44: 624MHz 4.50 100% 0% 99% 0% 0% 0% 100.1°C 1/1 [ 3314.299373] thermal thermal_zone0: critical temperature reached (105 n Message from syslogd@localhost at Dec 3 10:53:51 ... kernel: [ 3314.299373] thermal thermal_zone0: critical temperature reached (105 C), shutting down Stopp…

My Orange Pi PC2 work fine with Stretch (mainline, 4.14.48) between 35 and 65 °C. I got only a minor (but annoying) problem: the board start overheating after a shutdown (sudo shutdown -h now) and reach >70 °C after few minutes. Is it a kernel problem? Or a hardware design fault?

I'm trying to boot from exp. flash from site (Armbian Stretch mainline kernel 4.19.y), board couldn't boot (LOG): U-Boot SPL 2018.03-armbian (Jun 11 2018 - 03:52:30 +0000) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000) NOTICE: Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):c9f55c0 NOTICE: BL3-1: Built : 03:52:19, Jun 11 2018 NOTICE: DT: sun50i-a64-orangepi-win INFO: Configuring AXP PMIC INFO: PMIC: DRAM voltage: 1.50V INFO U-Boot SPL 2018.03-armbian (Jun 11 2018 - 03:52:30 +0000) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL3-1: Running on A64/H64 (1689) in SRA…

Hello guys! I'm beginner of Armbian. The problem is: Install Armbian Stretch mainline kernel 4.14.y on my device(Orange_Pi_PC),But I don't know how to enable UART1 . I tried to select UART1 & UART2 & UART3 on armbian-config,now i can see 'overlays=uart1 uart2 uart3' in /boot/armbianEnv.txt Connect serial device with P40(RX) P39(GND) P38(TX) . when i check serial device on ssh, i can see this info: uname -a Linux orangepipc 4.14.84-sunxi #3 SMP Sat Dec 1 07:18:41 CET 2018 armv7l GNU/Linux ls -l /dev/ttyS* crw--w---- 1 root tty 4, 64 Dec 4 20:24 /dev/ttyS0 crw-rw---- 1 root dialout 4, 65 Dec …

hello , I have Opi lite 2 I want to use it as low load server with minimal power consumption (min temp) I edited /etc/default/cpufrequtils like that min_speed=120000 max_speed=480000 governor=ondemand but it works on 888mhz constantly with load and without load (image 2) Ps: I have also OPi PC+ and edit of cpufrequtils works ok on it (image 1) what am I do wrong, or maybe armbian-config monitor doesn't work properly ? ARMBIAN 5.67.181202 nightly Ubuntu 18.04.1 LTS 4.19.4-sunxi64

Because of my mistake After Update of kernel 4.19..... cubietruck don‘t Start https://r.tapatalk.com/shareLink?share_fid=1017055&share_tid=8857&url=https://forum.armbian.com/index.php?/topic/8857-After-Update-of-kernel-4%2E19%2E%2E%2E%2E%2E-cubietruck-don%E2%80%98t-Start&share_type=t I wan‘t To do a Backup of my Running System or a Image so i can Flash it on a other SD Card or restore the Backup Thank you Gesendet von iPhone mit Tapatalk

Hi. I am trying to perform pairing with the Bluetooth Low Energy device using the bluepy library. This library uses the MGMT for ble. The command 0x0019 (MGMT_OP_PAIR_DEVICE) returns success status (0x00). But using the sniffer I didn't found pairing request packet. Then I tried to perform pairing using btmgmt tool with the same result (not paired, but success is returned). Then I tried to use Bluetooth manager. User interface added the device and pairing returned success. But during the pairing my device wasn't indicate successful pairing. I still can't to read characteristics with no mitm protection. Which means that device is not paired. …

Hi, I am using NanoPi M1+ device with Armbian Bionic kernel 4.14.y OS in it. On doing hciconfig ... I get no output. on doing hcitool dev ... the output is none too... What is the issue here? Why can't I see the bluetooth device of the device?

Hi, I'm trying to use bluetooth with the Mainline 4.11.9-sun8i armbian kernel (I also tried 4.11.7-sun8i). I activated ttyS3 (uart3) in armbianEnv.txt: verbosity=1 logo=disabled console=serial overlay_prefix=sun8i-h3 rootdev=UUID=59c35982-ddad-4bf0-8b72-a8974bfe88a6 rootfstype=ext4 overlays=uart3 spi-spidev param_uart3_rtscts=1 param_spidev_spi_bus=0 Unfortunately hciconfig -a does not find any device. I already tried to set the baudrate but no chance to get bluetooth alive: service bluetooth stop rfkill unblock all echo "0" > /sys/class/rfkill/rfkill0/state echo "1" > /sys/class/rfkill/rfkill0/state echo …

I need help. I builded image Armbian_5.67_Orangepiwin_Ubuntu_bionic_next_4.14.81_desktop. Ethernet don't work. Wi-Fi is Ok. When I tested image Armbian_5.59_Orangepiwin_Ubuntu_xenial_default_3.10.107_desktop Ethernet and Wi-Fi worked on the same board. armbianmonitor -u System diagnosis information will now be uploaded to sysctl: permission denied on key 'vm.mmap_rnd_bits' sysctl: permission denied on key 'vm.mmap_rnd_compat_bits' sysctl: permission denied on key 'vm.stat_refresh' http://ix.io/1s78

On the download page images have kernel 4.18-rc7 I need headers for this kernel. How to find which commit is these images are built from?

Hello everyone. My OP-PC is dead, with NO HDMI signal, NO console output, NO network output (LEDs off), only 1 LED is on which indicates SD card inserted (if SD card removes, it off). when use newly created SD card with Armbian, SDcard OS partition not resized. when connect to power supply, I can hear current noise. before it dies, it runs armbian server image with mainline kernel (4.14), it doesn't look like thermal fail, due to it runs very well during summer. I guess it is shorted some place, but I can't find where! so which hardware test point could I use to detects hardware failurtes.

I can't make bluetooth work on my OPi0+ Is it a known bug? Am I doing it wrong? thank you

Hi, I try to play with Armbian Stretch mainline kernel 4.14.y on Orange Pi Zero and need for my idea sf funktion (SPI) and i2c in u-boot terminal. I've build mainline U-Boot but the files in /boot directory from armbian looks so "strange". There is any description how to replace the files or make changes. Thanks for help. P.S. Have a lot of experience with uC programming, less with Linux.

I connected FA-CAM202 ( 2M USB cam provided by FriendlyArm) to USB2 pins on Nanopi Duo, The OS is Armbian Bionic mainline kernel 4.14.y The V4l applications output error as Unable to start capture: Input/output error i: Error grabbing frames The dmesg shows uvcvideo: Failed to query (GET_CUR) UVC control 3 on unit 1: -32 uvcvideo: Failed to set UVC commit control : -32 (exp. 26) This Cam FA-CAM202 is worked on PC while other USB CAM such as Logitech works on the same configuration of Nanopi Duo, on USB2. It is more like a driver compatibility is…

Hello guys, I trying to make my ili9431 to show early stage of boot console. Everything works great if I load from /etc/modprobe.d/fb_ili9341.conf but if I load from armbianEnv.txt nothings happen. I suspect that I am trying to load the device before the driver is loaded. I read about "platform file" here: https://github.com/notro/fbtft/wiki/Boot-console but I have difficulties modifying the files because the guide is for RPI. Can someone guide me or at least to know if I'm on the right track? Hardware details: Device: Orange PI Zero Plus2 Kernel: Linux orangepizeroplus2 4.14.83-sunxi …

RTL8211D PHY on OrangePi Prime is not detected neigther in uBoot mode or Kernel mode. Will share the logs ASAP. Please suggest!

First up, I did have a good dig around but couldn't find anything discussing my problem but if there is a thread already existing please just link to it, no need to get huffy. I have a problem with armbian on NanoPi NEO where USB devices are not properly detected at start up (warm or cold start). Armbian version details: BOARD=nanopineo BOARD_NAME="NanoPi Neo" BOARDFAMILY=sun8i VERSION=5.67.181115 LINUXFAMILY=sunxi BRANCH=next ARCH=arm IMAGE_TYPE=nightly BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage I have also tried nightly build Armbian_5.65_Nanopineo_Debian_stretch_next_4.14.78.img. The…

Hi, I'm using several Orange Pi Zero boards. At any given time, when I run "reboot now", I can no longer access the OPI via ssh. I tested the following distributions: Armbian_5.25_Orangepizero_Ubuntu_xenial_default_3.4.113 Armbian_5.59_Orangepizero_Ubuntu_xenial_default_3.4.113 All the programs I installed, which start from boot normally work, but I can not access via SSH. Is there any corruption of ssh files? Thank you for your help

Hi I have added some drivers in the kernel source code in the cache folder and I am not sure how to rebuild the kernel with the new changes. I am trying to rebuild the mainline kernel. Using compile.sh overwrites the changes with default files. I have changed the following configurations in my config file. KERNEL_ONLY="no" # leave empty to select each time, set to "yes" or "no" to skip dialog prompt 3 KERNEL_CONFIGURE="no" # leave empty to select each time, set to "yes" or "no" to skip dialog prompt 4 CLEAN_LEVEL="" # comma-separated list of clean targets: "make" = make clean for selec 5 # "debs" = delete pac…

Hi, I got one of those cheap 300Mbps wifi dongles with 8192EU chip How can we enable this in Armbian? Only lsusb has the following https://ibb.co/gYxyYT

I had to resolder the pins of the debug port on my NanoPi NEO Air and must have damaged the RX connection as I am unable to send commands but can receive read the debug output fine. Is it possible to change the debug port to UART1 or create another root terminal at another serial port?

Today I re-installed my Cubietruck as it was really outdated. It had: Linux cubietruck 3.4.105-cubieboard #8 SMP PREEMPT Fri Jan 23 06:11:42 EST 2015 armv7l GNU/Linux still running without issues. I reformatted the SD card with: ARMBIAN 5.65 stable Debian GNU/Linux 9 (stretch) 4.14.78-sunxi Configured everything and now I want to move the data to my SSD. (just as I had before) However dmesg shows me: cubietruck ata1: SATA link down (SStatus 0 SControl 300) What did i miss??

I would use the opi as ir transmitter for AC. Does anybody know if it is possible? Thanks

My Cubieboard 2 absolutely refuses to boot from microSD. It will boot into Android from flash when there is no microSD card inserted, but with a card in, it just produces a single red LED and no video output. Eventually it will respond by flashing green and powering down when the power button is depressed, so I feel like it's getting somewhere, but those are the only signs of life. I don't know how to look at serial output from this machine. I've tried two different power supplies, and two different monitors because one had I think been dodgy with this machine before. Same problem on all permutations. I also tested the SD card with F3 and wrote it with Etcher, and I've us…

Help with connecting the camera. I have already tried many different images and means, but I never managed to launch the CSI camera. Someone was talking about the 3.4 linux kernel on armbian to make it work, but I don't know where to find it. Can anyone have an image on which the camera works?

Hello, Has anyone tried to bring up a SIM7100E based hat on Orange PI Zero over the UART GPIO interface? I have enabled the UART ports in armbianEnv.txt as follows: overlay_prefix=sun8i-h3 overlays=usbhost2 usbhost3 uart1 uart2 dmesg | grep tty shows : [ 0.000379] console [tty1] enabled [ 1.765329] console [ttyS0] disabled [ 1.785581] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 39, base_baud = 1500000) is a U6_16550A [ 1.785700] console [ttyS0] enabled [ 1.810679] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 40, base_baud = 1500000) is a U6_16550A [ 1.835564] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 41, base_baud …

Hi guys, I have the bad idea to build up little by little some house automation with an opi1 that I don't use. Just for fun. So I'd like to start with armbian and build everything from there, with no precompiled images. The first thing I want to try is Google assistant. Can I use the assistant sdk that I can find on official website? Or there is something better for opi? Can I eventually integrate it with something like Hass.io or similar? I'm open for any advice. Thank you in advance

Hi, how you decode video on Nanopi Duo with hardware acceleration? Have you any images or instruction how i could test hardware acceleration by using Nanopi duo? Mainline kernel doesn't support hardware acselleration, right? I tried build image with legacy kernal (3.4.x), but it doesn't run. Any ideas?

Hi, I have a BananaPi Pro with A20 cpu. I try to install Motion and Motioneye but it fails. I found some tutorials but nothing worked for me. Is there any proper tutorial about how to install it? Thanks.

I have OrangePi PC and I'd like to use HC-12 serial communications device. I've successfully used it with RaspberryPi Zero with these instructions: http://dev.drun.net/2017/05/10/reading-hc-12-from-rpi-and-sending-to-domoticz/ I've found this useful info: https://forum.armbian.com/topic/1524-orange-pi-one-how-to-enable-uart/ I've connected the HC-12 to OPPC as follows: VIN – Connect to 3.3 (PIN 2) GND – Connect to GND (PIN 6) RX – Connect to (PIN 8, UART0_TXD) TX – Connect to (PIN 10, UART0_RXD) I've got Putty connected to OrangePi. command "ls /dev/tty*" shows that I have /dev/ttyS0. I've tried to use it with Minicom: sudo…

In the last weeks I've successfully installed Armbian Debian Stretch 5.59 onto a Banana Pi M2 Berry, now I'm trying with a Banana Pi M1. From https://www.armbian.com/bananapi/ I've downloaded the Debian Stretch image and wrote it to my 4GB SD-card using Etcher (on Windows 10) - Etcher meant it was successfully after writing. I've safely ejected the SD-card from Windows, plugged it into the Banana Pi M, but it tries to boot from the network. Then I've taken a look at https://dl.armbian.com/bananapi/archive/ and downloaded Armbian-5.59 Debian Stretch image, wrote it with Etcher again, booted. Same issue. It shows a red armbian logo with "initializing boot loader…

Hi, I've been using armbian in combination with openmediavault for the last years to access my files on an 1TB HDD. Today I wanted to upgrade the drive to a 3 TB one, but it just shows a capacity 746GB. Is there a size limit on the GL830 for harddrives or why isn't the real capacity showing up? fdisk-l: Disk /dev/sda: 746.5 GiB, 801569724416 bytes, 1565565868 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Thanks in advance Regards, Joshua