Allwinner sunxi

Hello, I am going to start looking into running Docker on OPi +2E soon, but before I get stuck in details I would like to know whether other people have had experience with it..? In particular, I would like to know what to expect when trying to run Docker on an OPi +2E. Having a report from prior experience would be helpful. As far as I understand, Docker is still in pretty much experimental stages on ARM. Kind regards, @ullbeking

Hello, What kind of speed can I expect from the ethernet on the BPM1? It's told to be 1Gb/s, but I am not even getting near that speed: wget https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.4.5.tar.xz ... linux-5.4.5.tar.xz 100%[==============================================================================================>] 104,37M 4,43MB/s in 24s 2019-12-18 22:38:33 (4,35 MB/s) - »linux-5.4.5.tar.xz« gespeichert [109435988/109435988] BPM1 and the router are set to 1000Mb/s, and the download line works at more then 100Mb/s. Downloading the same file on my PC shows a considerably difference: …

Hello I upgrade my last version Armbian and after shutdown the system the next day armbian won`t start. I download newest version burnd SC card an after loading is restarting 30 times. So I change new sd card burn one again armbian and is the same. I use converter from HDMI do VGA - and my experience is that converter very stress CPU so i connect directly to TV with HDMI but is the same Could You advice how to install Armbian on my OPI WIN PLUS. Regards\

hi all, I've been running into an issue where the kernel starts throwing error messages (https://pastebin.com/bmPJPeq0), the board becomes very slow and the cpu load goes to 11 and stays there. This seems to happen when I change the CPU freq using armbian-config to anything lower than 528MHz. Any ideas how I could resolve this?

I installed Armbian_5.75_Orangepizeroplus2-h3_Debian_stretch_next_4.19.20. But it can't boot up. These image can boot up. Armbian_5.65_Orangepizeroplus2-h3_Debian_stretch_next_4.14.78 Armbian_5.69_Orangepizeroplus2-h3_Debian_stretch_next_4.19.13

I'm using g_ether to connect OrangePiPc+ to network over USB OTG. On legacy kernel, that was giving 140 Mbits/sec IN (download from network to OrangePiPc+) and 170 Mbits/sec OUT. After upgrading to mainline kernel 4.19.62 (or 5.3.9), IN throughput degraded to 93-98 Mbits/sec (while OUT improved reaching up to 210 Mbits/sec in CDC EEM mode). This easily reproducible on both my boards OrangePiPc+ and OrangePiZero with latest Bionic images (clean installations + "modprobe g_ether iProduct="Linux-USB Ethernet/RNDIS Gadget" iManufacturer="Netchip Technology, Inc." dev_addr=02:81:05:F0:5C:24 host_addr=02:81:05:F0:5C:23 use_eem=0" ). Any ideas where is the bottleneck…

I tested the recently added sunxi-dev patch to improve the SATA write speed. Here are the results: Board: Cubietruck OS: Ubuntu Bionic (18.04.2), Armbian 5.86 Kernel: 5.1.0 with and without RFC-drivers-ata-ahci_sunxi-Increased-SATA-AHCI-DMA-TX-RX-FIFOs.patch SATA-device: SAMSUNG SSD 830 Series, 256GB Measurement method: dd if=/dev/zero of=/tesfile bs=? count=? oflag=direct bs: measured 4k, 64k and 1M block sizes count: adjusted to ensure that data written is ~500MB Measurements below are made with kernel 5.1.0 without (before) and with the mentioned patch: dd bs Before MB/s After MB/s Increase 4k 13.3 …

How can i use multiple microphone with Orange Pi Zero to make voice enable device?

Hi all! First time poster, i apologize in advance for any etiquette violations... I have an OrangePi Zero H2+ board and the DS18B20 sensor (waterproof version). I have soldered the pullup resistor between power and data cables. I have Armbian Stretch 5.83 with 4.19.38-sunxi kernel. I have enabled the w1-gpio overlay and loaded the w1-therm driver. Data is on PD14 (GPIO 10), power is on 5v (tried also on 3.3v) I can see this in my dmesg: [ 10.371825] w1_master_driver w1_bus_master1: w1_search: max_slave_count 64 reached, will continue next search. [ 58.171052] w1_master_driver w1_bus_mast…

Hello guys, I am experiencing such a problem: When I boot my orangepi it starts and it is visible in the router's page view getting IP with dhcp. As soon as I connect over ssh (at least this is the way to trigger it, not sure if it is hapening automatically after a while), the device disappears from the network and it is no more available! I have seen this behaviour happening on 2 different routers. Then I rebooted the device again and in the router config I put the same IP statically linked to the device and I tried to connect over ssh and it worked without disappearing anymore. So it sounds like a bug somewhere using dhcp protocol. Is som…

Can anyone answer here do bionic kernel supports HDMI output for Opi PC boards? Please suggest a solution as I have taken Opi PC board which has Armbian Bionic Image but no HDMI sound is coming out.

Hello, I've just found a topic about removing Allwinner legacy. I work with Orange Pi PC Plus board, H3 CPU. Do I understand correctly that the option to build system based on old v.3.4 kernel will be removed? Once I experienced a problem with system shutdown using newer kernel - got System halted message. This is why I decided to continue with legacy kernel. Please advise.

Hi guys a having problems to boot the latest armbian buster 5.3.Y kernel on the orange pi win plus. I tested other older kernels(4.19 and 3.xx) and worked fine except for Bluetooth and WiFi hotspot. I am trying to upgrade to buster 5.3 but always as result kernel panic(same on bionic and stretch 5.3). power supply is ok and tested on 3 microsd card. this is the debug information from an ttyS0 consoles it is continues rebooting. need some help debug.txt

Hi, I have a problem with an OrangePi that I have set up to host Octoprint for my 3d printer. It connects to the wifi just fine(receives wifi IP and I can ping e.g. google.com), but this is all checked through a serial interface, because I can not connect via my network(through SSH) and I can not see the webserver that Octoprint should host. I can't even ping the OrangePi from my computer. What solves the problem for me is to ping my computer from the OrangePi(via serial console). First then I can connect via SSH and see the web page or ping the OrangePi from my computer. If I plug in ethernet to the OrangePi, there is no problem. I have searched …

Hi All, I am looking for h3consumption utility to change ddr freq (I want to set ddr and processor as low as possible) Could someone help me ? Best Regards, Boris

Hello there, I tried to use on OPC3 bionic the ttyS1 for communcation with a serial device and didn't get it to work. ttyS3 works fine. Configuration is done for both. But now I need to communicate with a second and possibly a third serial device. So I hoped for updates. But now I can't find a download of the bionic version and i have to make decision how to go further on. Does it make sense to switch to buster or stretch? Is bionic only temporarily or finally offline? Whats the reason? Any idea when there is a chance to get a stable release. Possibly with 6 Months or surely not within 6 months. Which version is more likely to …

Thank you for bringing USB3 to life on the lite2 again!

Hi, Using the latest Armbian release (19.11.3) on OPi Zero (512MB, board revision 1.5) I have a strange issue. On kernel 5.3.x, Ethernet connectivity drops sporadically, around once every couple of minutes, for typically 10 seconds or so and then recovers. When the drop happens, a ping from another machine on the network produces 'no route to host' - then after around 10 seconds or so the network comes back up. The OPi Zero continues running normally during the 'outage', without functional network access. There is nothing in the dmesg log when this happens. Switching to kernel 4.19.62 from armbian-config, everything works perfectly. Back to 5.3.x, the iss…

Hello, Thanks for making ARMBian! I would like to be able to use it with my Orange Pi Zero LTS to make a PI-Hole. I'm using Armbian_19.11.3_Orangepizero_buster_current_5.3.9 However, I keep having problems with locales, such as : Warning: Invalid locale (please review locale settings, this might lead to problems later): locale::facet::_S_create_c_locale name not valid How can I fix it ? Thank you.

Hello, I've been working with my Banana Pro since years with Bananian. Last days I formatted the SD and installed Armbian (debian), to be used in headless mode. Installation and system setup worked as expected, I modified eth0 setup for static IP and it went fine after reboot. A strange problem appeared when I installed transmission-daemon, minidlna and samba packages. All working fine before reboot, but thereafter any network interface is disappeared, network-manager can't execute fine, remains running for several seconds then something crashes. If I configure eth0 manually network works, so no hardware problem. I'm sure the board work…

I have tested Armbian_19.11.3_Orangepipc2_bionic_current_5.3.9 and Armbian_19.11.3_Orangepipc2_buster_current_5.3.9 images from the official download site. The Debian Buster image is fast and stable. The Ubuntu Bionic build have random hangs on different boot positions. Sometimes works, but after reboot it hangs again randomly. I have burned the the images to the same microsd card. (Toshiba 32GB) I have tested with other microsd cards like Sandisk Extreme 32GB, Samsung EVO+ 32GB. I have the same results. The power supply is enough for the board. (5V 4A) This is not my first orangepi board, so I know how to burn the images to the sdcards. screenlog.bionic.0 (problems)…

Hey guys, I have a OP3 H6 and I cannot seem to find out why the 4 x USB ports are not working only the single USB next to the HDMI works. Any Ideas? Cheers!

I have a board of Orange Pi One Plus with installed pihole (https://pi-hole.net/). Armbian image is Armbian Buster with latest updates. PRETTY_NAME="Debian GNU/Linux 10 (buster)" Each 2-4 hours the device hangs and not able to respond to any command until I reboot it. The max uptime that I was able to gain was ~25 hours. I've changed power adapters, powered it via microUSB - same result. Looking at the logs I really have no clue why it stucks. Attaching debug, kern and syslog. Probably someone may pinpoint what's going on. P.S. Previous OPi One (not Plus) worked for that purpose like a charm. Didn't know that bying Opi One+ for upgrade will buy me loos…

Hi, I have two questions: 1. Where can I download the latest image for my board? rom this forum entry I see there is no armbian image for the first Orange Pi? The link https://www.armbian.com/orange-pi/ doesn't work, as it redirects to https://www.armbian.com/orange-pi-plus/ which is definetly not the same (A20<>H3) 2. After doing a 'firmware upgrade' from armbian-config, it identifies itself as a Banana-pi. Is it normal? The MOTD is BPi and armbian-config shows BananaPi as well.

Hello, I am on a nano pi neo, I get an optical input with an external usb audio card. I d'ont know how to use the onboard spdif as an optical input so is it possible to get the optical input of an usb card (wich I see with alsamixer) an output sound to the local analog output (I already can play sound on this output) ? Maybe a loopback or an audio software could helps.... Best Regards

Is there Hardware virtualization support available for orange Pi PC3, which have H6 family processor ? Can we port Xen hypervisor over it ?

Armbian Bionic mainline based kernel 5.3.y Server or light desktop usage scenarios. High level of software maturity NOTE: the download link is broken 404 Not Found nginx/1.14.0 (Ubuntu) Thanks a lot

I have tried to setup user quotas on my Orange PI PC2 and realized that there is no quota module in kernel at all. Switching between all kernel versions with armbian-config utility and all the same - they don't have quota module. Why there is no such necessary module? Is it possible to install this module and how? P.S. Sorry, maybe i have selected wrong chapter for my question

(picture courtesy @renaudrenaud) We spotted a new OPi Zero variant with one USB-A receptacle missing and replaced by a second RJ45 jack a while ago (in this report where a lot of 'information' seems a bit questionable to me) Today @Icenowy confirmed existence of this board since Xunlong announced it in a chat group. I believe this is somewhat related to recently available Orange Pi Zero Plus since by looking at the picture we can see behind both Ethernet MagJacks small packages. My bet is we're talking here about RTL8211E (Gigabit Ethernet PHY connected via RGMII to the SoC) and RTL8153 (Gigabit Ethernet MAC/PHY USB2 Hi-Speed attached to the SoC). …

I've been happily running orangepipc with armbian (buster, 4.19.62-sunxi) as an openvpn gateway for my home devices for some time. Here are some details: I have a remote openvpn server the pi runs an openvpn client and connects to the server the pi has ipv4 packets forwarding enabled my wifi router provides the pi's ip as the default gateway via dhcp So when I connect to wifi with my phone, all phone traffic will be routed through the remote openvpn server without need to install the openvpn client on the phone itself. With this setup the pi can easily saturate my 30mbit cable connection when downloading torrents for e…

Hi there Community! Can someone please inform why Buster Minimal images based on Kernel 5.3 are showing as unsupported for OrangePi Zero, although they are available for (nightly) download? Can I offer any help testing or something? Thanks.

Встроенный микрофон не работает при установке рабочего стола.

My development board is Orange Pi One, my development board installed armbian, but its Language Supports work is not normal, open for a while there will be flashback phenomenon! ! ! Help everyone to give a solution! ! !

New toys to play The NanoPi Neo Core and Core2 are the Core-PCB without Connectors. Only Pin-holes in 2.54mm Pitch. But as the Pictures did show - there will be a Docking-Board like on the NanoPi Duo The price for the normal NanoPi Neo jumps from $7,99 to $9,99 and the new Neo Core now costs $7,99 (256MB and no eMMC) BUT has optional - also like the Neo Core2 (here 8GB default) - 8GB eMMC (512MB and 8GB eMMC = +$10 on the $7,99 Neo Core) The Neo Core2 does cost $24,99 but do have 1GB of Ram and (default) 8GB of eMMC (more options later). (long description show also - a obsolete? - option for only 512MB. But the board…

Wanted to share my very positive experience upgrading to the latest kernel. Followed the procedure using armbian-config and it worked out of the box on my OrangePi PC2. Left the system overnight running my standard tests and no issues. Even the problematic rtl8192 has no issue. There used to be a slight judder on the HDMI attached monitor that is gone now, perhaps due to the new MALI450 gpu modules. ___ ____ _ ____ ____ ____ / _ \| _ \(_) | _ \ / ___|___ \ | | | | |_) | | | |_) | | __) | | |_| | __/| | | __/| |___ / __/ \___/|_| |_| |_| \____|_____| W…

Hi, I am running Debian buster 10.1 with following kernel on nanopir1 (1Gb of RAM) Linux srv-nanopir1-170 5.3.9-sunxi #5.99.191113 SMP Wed Nov 13 08:12:49 CET 2019 armv7l GNU/Linux I have all services up on local LAN Ethernet port, but not possible for me to setup WAN Ethernet port . Packages installed are .... The boot sequence is ... My current network configuration in udev is .... As a result, r8152 kernel module is correctly installed After connected one RJ45 to external DHCP server (running) , it is not possible to setup interface …

Hi, as it is quite hot now in Europe, one of my boards is experiencing overheat and shuts down automatically: Jun 25 16:52:27 localhost kernel: [74505.568246] thermal thermal_zone0: critical temperature reached (90 C), shutting down Who is initiating this shutdown? Is it possible to: 1. Change the temperature value that triggers the shutdown 2. Hook a script instead of direct shutdown so I can handle the overheat Thanks

Hi, Thank you very much for all the work. I recently purchased 4GB RAM version of Orange PI RK3399. Was able to install armbian WIP version: 4.4.180-rk3399 I'm trying to capture video via HDMI IN port using gstreamer but I see the following error messages in kernel log, Spoiler Jun 12 03:19:37 localhost kernel: [ 3.956986] tc358749xbg 1-000f: probing... Jun 12 03:19:37 localhost kernel: [ 3.957006] tc358749xbg 1-000f: GPIO lookup for consumer int Jun 12 03:19:37 localhost kernel: [ 3.957016] tc358749xbg 1-000f: using device tree for GPIO lookup Jun 12 03:19:37 localhost kernel: [ 3.957101] tc…

I would like to make Orangepi zero to capture USB output destined for a printer in order to log the output from a system. 1 ) Mimic the connected USB printer (so that the machine thinks it still has the original printer attached) 2 ) Capture the output from the machine 3 ) Send the captured output to the printer.

On Nanopi Neo Core 2 LTS (Allwiner H5) : - Armbian Stretch stock : speedtest Down:90Mb/s Up:80Mb/s - Armbian Buster stock : speedtest Down:90Mb/s Up:4Mb/s Maybe regression in network drive ? I was not able to find any information on this issue ... Could you help me please ?

About 3 months ago i bought the Orange PI Zero Plus Orange Pi Zero Plus I installed Armbian Stretch and started playing around. I noticed that it got up to 71c which was to much so i shut it down and went on the net to buy some 5v fans to cool it. A month ago I received the first fans and noticed now that Armbian Buster had arrived. Since I hadn't gotten far with the config of Armbian Stretch I started on a new image. But to my disappointment the ARM processor is now clocked to 1008Mhz and not the 1.2Ghz the device is set to by manufacturer. I can guess that it is because of the heat problem that it is now set to…

Hello, I've been trying to compile armbian for my OrangePI Zero Plus H5 with NEON and VFPV support for OpenCV . If I use the providede default image from OrangePI I can see that NEON and VFPV are enabled with lscpu command. When compiling armbian from source or downloading the pre-compiled images, I see the following: root@orangepizeroplus2:~# lscpu Architecture: aarch64 Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0-3 Thread(s) per core: 1 Core(s) per socket: 4 Socket(s): 1 NUMA node(s): 1 Vendor ID: ARM Model: 4 Model…

Hello, I have an orangepi win plus and I installed "Armbian_5.90_orangepi_ubuntu_bionic_next_4.19.57_desktop". I'm using ttyS2 and ttyS3 ports and working well for serial ports. But bluetooth not working. Bluetooth icon is shown at right top on screen. When I clicked bluetooth on and click search new devices, system say to me "adapters not found." I tried, And too many options I can't remembered but I can't. How to devices bluetooth on? If you have more information, I will send you any information from terminal. Sorry for bad English. Thanks for help.

Hello I having some issues with the Armbian Buster image for Nano Pi Neo 2. https://www.armbian.com/nanopi-neo-2/ When I launch the command sudo apt update, I'm getting the following error: The package cache file is corrupted, it has the wrong hash I already downloaded the image several times, I still getting the same error. My SD card is ok, I have tried with 2 different ones. I can remember having the same issue with a preview version. What's wrong??? Thank you

Hi all, First of all sorry if i posted in the wrong directory I'm currently facing some issues with my orange pi one and in particular with node red and my dht22 temperature and humidity sensor i installed the stable buster version on my sd card this works perfectly and after that i installed node-red on it. in node red I installed the dht sensor pallet and added it to my flow but here is were the issues are starting, i need to select which pin it is connected to and what gpio i use. i can only select bcm gpio, rev1, rev2 or wiringpi 1 or 2 and then which pin it is connected to. i have the sensor connected t…

Greetings all. I am having no success getting access to gpio pins in NR using opi-gpio. I am trying to re-build a system that I messed up due to an update. The update broke access to the 1-wire host adapter I had running on I2C. I have searched and read a lot trying to find a solution but I am not making enough sense of the solutions I read to even know if they apply or if I am applying them correctly. Very frustrating because I had this working once but that was a number of versions ago for both armbian and NR. Also, the gpio pins were working even after the I2c update. In the process of 'fixing' that I started over with current armbian: mil…

I do not use wifi at all, so I'd like to disable it completely. It's not configured right now, but I wonder if I could power down whole chip, ex. commenting it out in DT file? Does it save some power or not?

Hello everyone, I've got an orange pi pite 2, I install in my sd card armbian, it start but when I login and create a new account and reboot, I see termianl and not the desktop of armbian, If i reboot it ask me again to login, but I can'f see the terminal.... PLEASE HELP....... THANKS

My PineH64, as well as OrangePI one plus (H6) were working fine using 4.18.rc7-bionic till I have tried apt upgrade I'm getting the following error on both. Any ideas? Thank you vm Starting kernel ... [ 2.104055] Internal error: Oops: 96000004 [#1] SMP [ 2.108938] Modules linked in: [ 2.111997] CPU: 1 PID: 33 Comm: kworker/1:1 Not tainted 4.19.11-sunxi64 #5.67.181221 [ 2.119819] Hardware name: Pine H64 (DT) [ 2.123750] Workqueue: events deferred_probe_work_func [ 2.128887] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 2.133679] pc : sun8i_dwmac_probe+0x16c/0x550 [ 2.138121] lr : sun8i_dwmac_probe+0x21c/0x550 [ 2.142560] s…

So I've installed and I'm running watchdog for some months now on BananaPi M1. I think it reboots the board when the default gateway has some issues. And that's fine, no problem with that. The board works 24/7 and it made 14+ days uptime without problems. But things have changed and the board reboots at least few times a day (seems I have a problem with armbianmonitor -u - the board rebooted twice before it ended). And here's the problem. watchdog doesnt log anything or I'm unable to find any usefull info. And watchdog.conf: (it seems that the board went offline - maybe internet connection issues, but I have another one running that's also "l…

Hi, I always been an retrorangepi user for my Opi1. but the lastest retrorangepi is stuck at 4.1 (I try the 4.2 slim but it's too slim) and the 4.3 beta also if its named as full, lacks of kodi and many emulators. so, my thought is. What if I build my personal emulationstation + lastest kodi on top of lastest armbian? Can I install armbian and then emustation and kodi? Do I have to install all emulator one by one? or I could use retroarch? Can I setup armbian to boot emustation? I think could be a good thing also for study

Good day, We use NanoPi Neo Core in voice information systems. We found a problem with the implementation of Dynamic Audio Power Management for Portable Devices in H3. Our program plays voice files using the standard call of the operating system - "aplay". Before starting the reproduction of each file the voltage is discharged and restored at the output of the DAC. This leads to a loud click on the output of the audio system. Setting pmdown_time = -1 does not save the situation. Can you help in solving this problem? P.S. This problem appeared in version 4 of the kernel.

I run the OPi Zero as a Pihole with etherned, and I would like to minimize power consumption as low as possible. 1. I did change the frequency to be between 120 - 960 Mhz, and ondemand. This probably reduces power and heat too. 2. I'm not sure how to disable USB (I don't need it at all) and WiFi. I read the threads, like this but not sure how to do. Can you please guide me? 3. I saw there are other options too, with a tool h3consuption, but I don't know how to install it and what can I do to squeze down a couple of mW's more. Your help is very much appreciated!

Hello, I just fresh installed Armbian_5.31_Lamobo-r1_Debian_jessie_next_4.9.7.img on my R1(which is for me a fantastic device). I tried to use GPIO by sysfs like I used to do on 3.4.113-kernel. on 3.4.113: echo "17" > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio17/direction cat /sys/class/gpio/gpio17/value echo "1" > /sys/class/gpio/gpio17/value gpio -g read 17 ...this is working fine ls -l /sys/class/gpio/ --w------- 1 root root 4096 Nov 4 19:17 export lrwxrwxrwx 1 root root 0 Nov 4 19:17 gpio14 -> ../../devices/platform/gpio-sunxi/gpio/gpio14 lrwxrwxrwx 1 root root 0 Nov 4 19:17 gpio1…

trying to know what is the chipset used for wifi in M1+ but it is not mentioned in hardware specs at wiki.friendlyarm.com ! .... with its datasheet. thanks in advance

Hello everyone, I want to do something simple with my OrangePi One Plus. That is to connect a bluetooth speaker and play wireless from the Pi with a CSR8510 A10 USB dongel. The dongel works and i can pair with every device. Even with my JBL Go 2 bluetooth speaker: hj@PLUS-OrangePiOne:~ $ sudo bluetoothctl [NEW] Controller YY:YY:YY:YY PLUS-OrangePiOne [default] Agent registered [bluetooth]# power on Changing power on succeeded [bluetooth]# scan on Discovery started [CHG] Controller YY:YY:YY:YY Discovering: yes [NEW] Device XX:XX:XX:XX JBL GO 2 [bluetooth]# scan off Discovery stopped [CHG] Controller YY:YY:YY:YY Discovering: no [CHG] Device XX:XX…

Hello, now I have some time to spend it with OPI Zero Plus2 H5 Try to download and install Armbian_5.90_Orangepizeroplus2-h5_Ubuntu_bionic_next_4.19.57, update it, and try to do something (bluetooth player) with this. But, no working BT device after fresh install. So, I must try to do something with this. (one more time) Now I have working script, see attach. Can anybody try this patch please ..? Thanks brcm43438-patch

I want my armbian (running on OrangePi lite) to output 2560x1440p60 resolution. the h3disp tool has an option for 2048x1536 (3:4) but not for 1440p. How can I get 1440p output?

Hi, when I try to connect to OPi Zero via USB TTL (PL2303) and run minicom -D /dev/ttyUSB0 -b 115200 -o, it seems to be normal until it booted to the Kernel then it start outputing garbage but when it started without USB TTL it just work normally U-Boot SPL 2019.04-armbian (Jul 16 2019 - 10:53:57 +0200) DRAM: 256 MiB Trying to boot from MMC1 U-Boot 2019.04-armbian (Jul 16 2019 - 10:53:57 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 256 MiB MMC: mmc@1c0f000: 0, mmc@1c10000: 1 Loading Environment from EXT4... ** File not found /boot/boot.env ** ** Unable to read "/boot/boot.env" from mmc0:1 ** In: serial Out:…

OPiPC2, with Armbian Bionic desktop mainline based kernel 4.19.y Using it as headless server, all X and desktop stuff removed. Using PuTTY to log in via SSH, line drawing stuff (as usual) only works if translation is set to ISO-8859-1 in PuTTY. mc looks great, but all ncurses-based software (aptitude, htop, bmon etc) does not. Main problem seems that horizontal spacing is "shrunk" whenever there is no text to keep it: This is even more dramatic for menu systems and anything that is column-oriented. Tried dpkg-reconfigure locales to switch system to ISO-8859, but no change, really seems to be an ncurses bug. No such problem…

After running "stress" with loadavg=6 for a while, wifi is lost and CPU temp fluctuates between 50-78C, and I saw 20+ errors such as: Write-error on swap-device all related to zram but I do have 130M RAM free, other than lost wifi and those errors shown, the system still appears to running, I can ssh via wired ethernet port and poking around it.

Hello, I have an OrangePi Zero H2 which until recently was running almost flawlessly with the Armbian_5.38_Debian_stretch_4_14_14 image. When I did a kernel upgrade using "apt-get dist-upgrade" (because I had earlier the error message ~"failed to Load Kernel Modules", and dist-upgrade was recommended), and this dist-upgrade failed inbetween (probably because of power consumption), the SD card was left in unbootable state. (error msg see below [1]) I concluded that the /boot directory was corrupted, so from a new installation of Armbian_5.38_Debian_stretch_4_14_14 made elsewhere I copied all the /boot directory over to my SD card. This m…

I'm wondering if anyone has had any luck using spi-gpio to bitbang SPI on the H5... @martinayotte, I found a forum thread from a few years ago where you seemed to be looking at this area - perhaps you have an idea? Doing a typical spi-gpio DT overlay for this properly loads the spi-gpio and spi-bitbang drivers, creates /dev/spidev0.0, and allocates the gpios (verified via gpiod)...but the first problem I see is that the CS line is simply not working (cs-gpios below)...? /dts-v1/; /plugin/; / { fragment@0 { target-path = "/"; __overlay__ { spi { compatible = "s…

Hello, I have downloaded and installed Armbian Buster mainline based kernel 4.19.y & Armbian Bionic mainline based kernel 4.19.y from https://www.armbian.com/nanopi-neo-air/ With both versions I have the same problem: WiFi is not working at all ! Before the installation I was running the Friendlyarm factory image and had no problems with WiFi. As I have no internet connection, I can not upload the ArmbianMonitor log. Running this gives no errors. root@nanopiair:~# armbianmonitor -v Starting package integrity check. This might take some time. Be patient please.. . It appears you don't have any corrupt files or packages! …

Hi ! I am using Armbian_5.65_Orangepilite_Debian_stretch_next_4.14.78armbian deb stretch image on orange pi lite. Its working great for the most part, but it misses the starting portion of the audio. I have installed snips voice assistant on it and for some reason the speaker does not produce the confirmation sound output on hotword detection. But plays rest of the sound outputs after that for another 5 seconds or so. Missing the confirmation sound from a smart speaker is really annoying. Is that a bug? Is there a possible workaround? Is any way this can be solved properly? Please point me in the right direction

hi guys sorry for simple questions , i installed Armbian_5.91_Bananapi_Debian_buster_next_4.19.59.7z on banana pi M1 , after login i try to statx for have desktop but not start , tell me not found , i try to search in google but not find nothing about this , i saw all tutorial start automatically the desktop enviroments, is possible install ?? or exist a guide?? thankz and sorry agin for simple questions

Hi, we experience change in owner:group in /var/log. Eg. mosquitto folder requires mosquitto:mosquitto and is changed to root:root. After this change mosquitto service is down. Any pointers are very much appreciated. Many thanks. Rostislav

I have Orange Pi Zero and plugged bad USB modem with power problems. Some moment modem have power problem and disconnect from board. USB port in Orange PI disabled after it - lsusb show one of two board's USB hub is absent After reinstall image in this board, USB hub works well. I think, USB hub disabled by OS when USB port has errors. Let me now. how to enabled USB hub without OS reinstall?

I have read two old threads in this forum: I have been running this (will post more details if needed) for a few days: VERSION=5.90 DISTRIB_ID=Ubuntu DISTRIB_RELEASE=18.04 DISTRIB_CODENAME=bionic DISTRIB_DESCRIPTION="Ubuntu 18.04.3 LTS" NAME="Ubuntu" VERSION="18.04.3 LTS (Bionic Beaver)" Kernel is 4.19.62-sunxi The BPi would hang/freeze, seemingly randomly within a day or two. When it does that, there is no HDMI video or response to ping. After reading the first thread, I did stress test on the BPi for more than 2 days. The BPi actually hold up. So, next I ran "ping -i 30 -D 192.168.8.1" -- pinging …

Hi I have issue to run bluetooth on OrangePI Zero Plus2 H5 with Armbian 4.14.63-suxi64 - what I donloaded from the armbian page where is my device and this image is supported. Wifi is working but I have issue tu run Bluetooth - I read many topics here but I dont understand what to do. Maybe Im doing some wrong. Can someone advice me what should be done, please. Current status after installation: * ap6212-bluetooth.service - LSB: Patch firmware for ap6212 adapter Loaded: loaded (/etc/init.d/ap6212-bluetooth; generated; vendor preset: enabled) Active: failed (Result: exit-code) since Thu 2019-10-31 08:45:14 UTC; 24min ago Docs: ma…

I am very confused. I don't know where the problem is. Have you ever encountered the same problem? Kernel 4.19.80-sunxi Debian Stretch armbian version 5.98 Orange Pi R1 No third-party hardware was added. Pure R1 bare board Start error message： [ OK ] Started LSB: set CPUFreq kernel parameters. [ 8.670214] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 8.681560] pgd = 95d3822c [ 8.684287] [00000000] *pgd=00000000 [ 8.687884] Internal error: Oops: 805 [#1] SMP THUMB2 [ 8.692942] Modules linked in: binfmt_misc 8189es zstd zram lima sun8i_codec_analog snd_soc_simple_card sun8i_adda_pr…

Hi, how can I enable hardware decode of video h264 mpeg on H5 chip? I use a Orange pi pc2 but video goes slow and lag very much. H5 SoC has very value hardware but isn’t possibile use mali GPU yet? Thanks

I coudn't find in menu System -> Install optin for cloning OS from SD to eMMC. How can I get it back as on older version? Boards are Orange Pi +2E and Orange Pi PC+ OS Armbian v5.91 I tied even: git clone https://github.com/armbian/config cd config bash debian-config but same... Thx

Hello Guys. เว็บพนันบอลต่างประเทศ เว็บแทงบอลต่างประเทศ HowTo: Setting up resolution 1600x900 & 1366x768 ? &how can i set up other resolutions those are not in h3disp like 1600x900 board is orangepi-pc

Greetings All, I'm trying to get my old Lexmark X1190 printer to work on my OrangePI PC without succes. I'm using the Xenial OS from armbian. Is there anyway I can get this printer to work on my OPI PC ? Thanks in advance Darren

Hi there, I was expecting /etc/machine-id to be unique for every install, but it is static which was very unexpected (I use it as the basis of machine-specific identifier which should have been globally unique). fixing it up was easy enough: rm -f /etc/machine-id rm -f /var/lib/dbus/machine-id dbus-uuidgen --ensure systemd-machine-id-setup Shouldn't this be done when the root fs is being resized on the first boot?

I'm connected to my Orange PI Zero over serial. I have a WiFi connection configured in NetworkManager on the Zero to my home AP/gateway, and it can connect to the internet over it. However: the Zero does NOT reply to ARP requests. I have tried running wireshark on multiple other machines on the same LAN, both wired and wireless, i have run tcpdump on the router, and none of them have EVER seen an ARP reply coming from the Zero. Obviously this means that no machine on the network can discover the MAC address of the Zero, and cannot connect to it... unless... the Zero first connects out. once the Zero has sent a packet to a machine, the machine will …

I'm running the latest lime1 armbian (linux 4.14) and am having great difficulty controlling the mic levels. amixer yields: Simple mixer control 'Left Mixer Left DAC',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [off] Simple mixer control 'Power Amplifier',0 Capabilities: volume volume-joined Playback channels: Mono Capture channels: Mono Limits: 0 - 63 Mono: 48 [76%] [-15.00dB] Simple mixer control 'Power Amplifier DAC',0 Capabilities: pswitch pswitch-joined Playback channels: Mono Mono: Playback [on] Simple mixer control 'Power Amplifier Mixer',0 Capabilities: …

I am trying out the latest Armbian Debian Buster release for a Nanopi Neo Air. It is working fine. I've loaded Armbian into the eMMC and I can boot off of it. I have done `apt update && apt upgrade`. Using armbian-config, I have configured Wi-Fi and can SSH in. However, Bluetooth does not work: # systemctl status ap6212-bluetooth.service * ap6212-bluetooth.service - LSB: Patch firmware for ap6212 adapter Loaded: loaded (/etc/init.d/ap6212-bluetooth; generated) Active: failed (Result: exit-code) since Thu 2019-10-24 04:12:56 UTC; 6min ago Docs: man:systemd-sysv-generator(8) Process: 1928 ExecStart=/etc/init.d/ap6212-bluetoot…

Hello guys and gals Can anyone help me what information to add in boot.cmd file to make it bootable from SSD on SATA port? I found some examples but they are from 2014 and the information in my boot.cmd file looks slightly different from what is posted in the past. I'm using the latest Buster Server image with 4.19 kernel. By the way is it a good idea to enable TRIM for the SSD? I saw some options in YouTube how to enable TRIM, but just want to ask for opinion of people with SSD drives, who already managed to boot from SATA with SSD. setenv load_addr "0x44000000" setenv overlay_error "false" # default values setenv verbosity "1"…

Is there any working image for Nano Pi Air that supports in same time: - Record in the format of the mpeg4 pipeline, the video codec used is h264. Resolution 1024x768 - Ability to transmit video over WiFi (WiFi AP mode), RTSP protocol. - Ability to connect via USB to transfer recorded files to a PC (USB device mode) - Update firmware via USB (FEL mode for Allwinner SOC)

Hi I' am trying to use the SPI device on the Olimex Lime 2 board but i am having a lot of trouble. Basicaly i do not see the spidev on the device three. i am using the last image (Armbian_5.91_Lime2_Debian_buster_next_4.19.59), i have activated the overlays and that is the my armbianEnv.txt file verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun7i-a20 rootdev=UUID=3563b9df-bd15-4366-b897-da0963dfd5a0 rootfstype=ext4 overlays=spi-spidev usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Where am i wrong? Thanks in advance for any kind of help

due to systemd updates to a new version, maybe it's not compact with old kernel. after system upgrade, it fails to start sshd. after read code, insystemd-tmpfile chase_symlinks() return -EBADF from kernel, I guess legacy kernel not compact with newer systemd.

HI, I have OrangePiPc and need to activate 3 uart (TX-RX) pins as system serial ports (/dev/ttyAMA0, /dev/ttyAMA1, /dev/ttyAMA2) how do it?

Hi All, Just wanted to share a good story using armbian. I have used in the past 1-wire probes for temperature, and the process included decompiling, editing and recompiling dtb for my Banana Pi M1, which was not easy at all. Every firmware update deleted by changes and had to redo de recompilation. With latest kernels and armbian version, the process is now extremely easy, just edit: /boot/armbianEnv.txt Adding this lines: overlays=w1-gpio param_w1_pin=PI3 # desired pin(7th pin (GCLK) or number 4 on first column where number 1 is +3V) param_w1_pin_int_pullup=1 # internal pullup-resistor: 1=on, 0=off …

Hi there, Orange Pi PC+, Armbian Stretch. What I want is to replicate current router (OpenWRT Barrier Breaker on TP-LINK MR3220 v1) on and Orange Pi. I use this router to "share" (using scp from host PC) an USB flash dongle (remote site backup). With its processor copying filer over WiFi SCP is terribly slow (1.2MB/sec). Network Manager "proposes" me to create an WiFi network, but with only NO security or only WEP. I use WPA personal. Configuration on router wlan0 as an AP (WPA), wlan0-1 as WiFi client (also WPA different SSID) with WDS enabled (to act as bridge member), eth0 as usual. All those 3 interfaces bridged together an …

Hello Guys, I have a problem with time in my Orange Pi Plus 2E. I have installed yesterday Linux orangepiplus2e 4.19.62-sunxi #5.92 SMP Wed Jul 31 22:07:23 CEST 2019 armv7l GNU/Linux and and I can't set right time. root@orangepiplus2e:~# hwclock 2019-10-07 16:52:25.994362+02:00 root@orangepiplus2e:~# date Mon Oct 7 16:56:46 CEST 2019 Now is 16:40 hour. Yesterday different was about 20 minutes, today is about 4 minutes. How to align the time? root@orangepiplus2e:~# hwclock --test -D hwclock: use --verbose, --debug has been deprecated. hwclock from util-linux 2.33.1 System Time: 1570460247.618048 Trying to open: /dev/rtc0 Using the rtc interfac…

Hi there, I have upgraded from Jessie to Stretch, apt-get update apt-get upgrade change repo name in apt config files update, upgrade. Now I lost some functionality: - X does not start, nor automatic nor manual, message "no screens found" - Firefox crashes even before main window open, no error message (remote X). In armbian-config I tried to install desktop, but command returns quite fast (much faster than on fresh Stretch). It seems no distribution problem, because I have installed Stretch on another card and there everything works fine. (except extreme slow screen update on remote X). What to c…

After last upgrade Armbian on OrangePi PC Plus from version ARMBIAN 5.73 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i - 3.4.113-sun8i #16 SMP PREEMPT Thu Jan 31 08:15:34 CET 2019 armv7l armv7l armv7l GNU/Linux to Ubuntu Xenial with Armbian Linux 3.4.113-sun8i - 3.4.113-sun8i #2 SMP PREEMPT Wed May 8 15:09:43 CEST 2019 armv7l armv7l armv7l GNU/Linux the modem on port ttyS3 stopped working. dmesg | grep S3 [ 0.621150] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 35) is a SUNXI ls -la /dev/ttyS3 crw-rw---- 1 root dialout 251, 3 Oct 15 13:03 /dev/ttyS3 script.fex [uart0] uart_used = 0 uart_port = 0 uart_type = 2 uart_tx …

Hi, I built Armbian (bionic) from source for Orange Pi PC 2 and everything went through fine. I burn to SD card and load it on the board and it boots well. Then I use "root" to login and forced to change password from default 1234 to somepass. Everything seemed fine until I tried to login with the new password (old password failed to work anymore). The errors are in following screen shot. Kinda new to this stuff, not sure how to fix it. Tried to connect to serial port but somehow a couple of TTL cable all failed to work. Still struggling. Please help!

Hello; It was tried with armbian buster, stretch and bionic. Orange pi zero connect wpa/wpa2 networks without problems, but connect to open network. I was trying different methods and wpa_supplicant conf file (key_mgmt=NONE) and different version of armbian. It cannot connect to open network. I need a solution for this problem. Thanks.

I have an Orange Pi Zero that had an uptime of well over a year monitoring the output of some solar panels and the state of charge of a battery. It then switches a couple of relays in response to these measurements. It has been really reliable for 2 years, never crashing or rebooting until now. At the beginning of September it started to stop working, it has no monitor or keyboard, only a cat5 cable, so when I say stop working, I mean it stops logging to the nfs drive, stops switching the relays, stops responding to pings and any ssh sessions timeout. It does this every few days, around 6:30 am, and I then have to power cycle it to get it to work a…

The problem I have an USB endoscope camera that works fine with my Orange Pi lite's normal USB port. However I need both USB port for other devices, so I want to connect this same USB camera, which was orginally marketed as USB otg camera for android phones, using Opi lite's micro usb otg connector. What have I tried - In armbian-config menu, I have enabled usbhost0. I believe this overlay is for the usb otg port, but just to be sure I also enabled usbhost1, usbhost2 and usbhost3. - Using dtc I decompiled sun8i-h3-orangepi-lite.dtb into sun8i-h3-orangepi-lite.dtc. - In this dtc file, I looked up musb, and changed status = "disabled" to "o…

Hi everyone, I am using Armbian. SPI overlay and "spidev" are already loaded "[ 2.614185] spi spi0.1: spi_setup / gpio_is_valid(21) ... doing gpio_request ... [ 2.614213] spi spi0.1: spi_setup / gpio_direction_output(21) done ! [ 7.256451] spidev spi0.1: probing from DT " Did someone succesfully used SPI on this board using WiringPi, WiringPISPI? I have an application that returns me "Unable to open SPI device: No such file or directory". I do have ls /dev/spidev0.1 I tried different libraries for WiringPi but no success. It seems that the library tries to load another module instead "spidev" that is already loaded in linu…

Hello! I have an Cubietruck with an attached SATA-Disk. I would like to use the board without an SD-Card (I don't see why I should use one when I have a nand and a Disk). I can boot u-boot-sunxi-with-spl.bin using FEL and Armbian boots successfully. I can write stuff to nand, but I didn't manage to write an working u-boot to nand. Is the SPL-Version the correct one or the one without? Do I have to write to something special like MBR? Where does the BROM search for the bootloader? Does it parse the partition-table? Thanks in advance!

Hi, I'm trying to create a DT overlay for my Cubietruck running 4.19.62 and I've placed it in /boot/overlay-user and changed the user_overlays entry in boot.scr to load it. It is being loaded but I'm getting FDT_ERR_NOTFOUND when trying to apply it. The overlay is meant to change the label and default-trigger entries for the four LEDs in the leds node. I'm using dtc 4.1.4 and it does compile this overlay. Can anybody tell me how I can change this overlay so it will work ? Or perhaps tell me if this is not possible. /dts-v1/; /plugin/; / { compatible = "allwinner,sun7i-a20"; fragment@0 { target = <&leds>; …

Hi, i get this error when i run the script by crontab. When I run manually, the script runs perfectly. crontab is executed by the command: "crontab -u root -e" To make sure the tasks are performed by the root user, but I still have the following error: hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --debug option to see the details of our search for an access method. Erro na sincronização Wed 02 Oct 2019 08:04:11 AM -03 This is the script: #!/bin/bash pingtest=$(ping -c 1 a.ntp.br > /dev/null 2>&1; echo $?); if [[ $pingtest -eq 0 ]]; then systohc=$(/sbin/hwclock -f /dev/rtc1 -w; echo $?); if [[ $systohc -eq 0 ]];…

During the last days the system crashed twice - by crashed I mean that no SSH or other connections was possible and I had to force-power off. I used it for months without crashes before so its probably related to a new SATA drive. I wanted to look at the syslog and I noticed that /var/log/syslog only shows entries starting from the current boot and the /var/log.hdd/syslog is empty. Do I understand correctly that armbian logs only to /var/log which is a ram drive so the logs (or at least the syslog) is never persisted? How can I find out whether the SATA drive is responsible and why? Maybe it has a too high power consumption under special circumstan…

I have an Orange Pi One Plus with the H6 chip in it and I'm quite happy with how well it's supported by Armbian. I haven't really had any problems with it. I do have one question, though. I'm using armbianmonitor to "-m" monitor the machine and I notice that the temps are always pretty hot. Even at idle (480MHz) it still shows 72C. That seems higher than I would have expected. Is this normal, expected behavior? I understand that the SoC thermal monitoring code in the kernel is pretty new and therefore might not be perfect, yet. So, I thought I'd ask. Because it may just be my board that's off. Does anyone know if this is normal? Info: …

Hi Everybody, I have the orange pi 3 and I am using Armbian Buster mainline based kernel 5.1.y but sound from hdmi doesn't work. I tried to fix it through /etc/alsa/conf.d/ and put pulse audio as default but nothing happened. I am new using this new version of orange pi and armbian. I hope you can help me. Best regards. Paulo.