Allwinner sunxi

I installed Armbian onto a reliable 16GB class 10 SD card, put it into an Orange Pi 3 with a 5v 3000 mA power supply (not a phone charger) and I've bumped into this error.. ALERT! /dev/mmcblk0p1 does not exist. Dropping to a shell! The armbianmonitor -u command was not found so I had to take a photo of the computer screen. I'm not sure what is going on here and I couldn't find someone who had this error on an Orange Pi 3 before. If anyone has some advice I'd love to hear it.

I'm trying to disable the HDMI output on my A20-OlinuXino LIME. I have tried to disable the HDMI from the u-boot console using this commands : -setenv video-mode sunxi:1024x768-24@60,monitor=none -saveenv I have also tried to recompile the boot.cmd but even in this way nothing. Corrently i'm using : Linux lime 4.19.62-sunxi #5.92 Where is my mistake? Thanks in advance.

Guys! I have two of the original Pine64+ boards from the kickstarter (with LCD) and tried to launch the latest armbian image on them. Both of them freezes in u-boot after it tries to evaluate USB connections... Rather strange, they work well with the ancient original images. ``` U-Boot SPL 2019.10-armbian (Feb 17 2020 - 09:25:19 +0100) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.2(debug):9560593-dirty NOTICE: BL31: Built : 09:25:06, Feb 17 2020 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x4095dd0, model: Pine64+ INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controlle…

After some hack, I use the SPI port on OPi One to connect with a MAX6675 board. The SPI port on One is SPI0, so armbianEnv.txt should include these: overlays=spi-spidev param_spidev_spi_bus=0 param_spidev_spi_cs=0 the MAX6675 connects to OPi One as: MAX6675 One GPIO ------------------------------------------ VCC PIN17 GND PIN20 SCK PIN23 CS PIN24 SO PIN21 Then use the attachment program to read f…

Good day! Tell me if there is support for hardware acceleration Orange PI WIN PLUS Cortex-A64 ?? I try to run a video (vlc,mpv) but it is very slow =(

I've created an armbian minimal image for my pinebook with luks encryption. It works fine but I cannot see the password prompt on screen... the boot process is: * The armbian uboot is displayed * Then a black screen... After a few seconds I'm assuming it is time to put my luks password, so I do it * Then the screen starts to show the boot text Is this expected? Am I doing something wrong? I don't want to install plymouth, just the usual LUKS password prompt. Thanks!

Hi! I didn't find much info in the forum on how to correctly apply RT patch to the Armbian (Orange Pi Zero Plus H5 board). Here is how I did: Built Armbian as follows: 1) I downloaded patch-5.4.22-rt13.patch from https://mirrors.edge.kernel.org/pub/linux/kernel/projects/rt/5.4/ and placed into ~/build/userpatches/kernel/sunxi-current ( I saw from the logs that this is the folder for the builder to search for user patches in my case) 2) Started ./compile.sh --> FULL OS image for flashing --> Show a kernel configuration menu before compilation --> orangepizeroplus (H5) as target board --> current (recommended , which is 5.4.23…

Hi everyone, I have a problem when work on OPi zero wifi which is running Armbian linux sunxi 4.19.62. I used nmtui to configure wifi connection with static ip. It works fine even rebooting or re-powering up however I tried to power off the router and the result is it has never reconnected again. Next, I plugged in the ethernet cable into RJ45 port, the connection is established. I use sudo ifconfig to show the information, I saw that both the wifi (static) and ethernet are correctly then I can access via ssh or scanning the ip. One again, I continued plugging out the ethernet cable, all connections were disappeared even wifi and connection via ssh is failed. …

Is it normal? Why Couldn't get bank PG regulator U-Boot SPL 2019.10-armbian (Feb 17 2020 - 08:31:10 +0100) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.2(debug):572fcdd-dirty NOTICE: BL31: Built : 08:31:00, Feb 17 2020 NOTICE: BL31: Detected Allwinner H6 SoC (1728) NOTICE: BL31: Found U-Boot DTB at 0xc07ef00, model: OrangePi Lite 2 INFO: ARM GICv2 driver initialized INFO: PMIC: Probing AXP805 on I2C INFO: PMIC: aldo1 voltage: 3.300V INFO: PMIC: aldo3 voltage: 3.300V INFO: PMIC: bldo1 voltage: 1.800V INFO: PMIC: bldo2 voltage: 1.800V INFO: PMIC: bldo3 voltage: 1.800V INFO: PMIC: cldo1 voltage: 3.300V INFO: PMIC: dcdcd voltage…

Gentlemen, I've spend time looking for the GPIO pinout for the Orange Pi Win I am using with Armbian. Specifically I would like to use SDA and SCL. Does Orange Pi publish some information on this subject? Thanks in advance for your information.

Hi there, I have 2 OPi PC+, one was with Jessie, then upgraded to Stretch, Working almost fine, only one issue was "systemctl start postgresql.service" not working. I used a workaround, "su - postgres -c 'pg_ctl start'". Postgres not from repo (previously was from repo) but compiled from source, as I need at least version 10 for "logical replication". Not at some point of time, I noticed message, that kernel package is to upgrade (3.4.112 to 3.4.113). After reboot graphics don't start. "No screens found". Ok, so I tried to upgrade (apt update, apt upgrade, apt dist-upgrade after changing name in /etc/apt/ files). Now it's almost crash: - graphics …

Hello After spending hours of trying to create an older DEV kernel (5.1.21) here are the following steps in order that it will work. I will describle here about the 5.1.21 kernel but I think it can work for any kernel. 1. create lib.config file under build/userpatches with the following: KERNELBRANCH='branch:orange-pi-5.1' 2. And this is what create the magic: download the Armbian files that matches that distribution and replace all the files in the build directory: for example I have downloaded from here - This link is the build version from the branch of the 5.1.: https://github.com/FireflyTeam/armbian-build/tree/e…

After update from armbian5.23 to armbian5.25 driver for gc2035 not work. The device isn't defined. =========== Armbian 5.25 ============== root@orangepipc:~# ls /dev/video* /dev/video0 /dev/video1 Where: /dev/video0 and /dev/video1 - v4l2loopback root@orangepipc:~# cat /etc/modules #8189es #rfcomm #w1-sunxi #w1-gpio #w1-therm gc2035 vfe_v4l2 #sunxi-cir v4l2loopback root@orangepipc:~# modinfo vfe_v4l2 filename: /lib/modules/3.4.113-sun8i/kernel/drivers/media/video/sunxi-vfe/vfe_v4l2.ko description: Video front end driver for sunxi license: Dual BSD/GPL author: raymonxiu depends: videobuf-core,vfe_os,vfe_subdev,videobuf-dma-contig,cci …

Dear all, Starting from NAND memory used to work fine on the nanopi neo plus2, however with the new boards (both v1.2 and v2.0 revision) we just obtained it frequently doesn't want to reboot, while a cold boot works fine (I tried also earlier u-boot versions (2019.04, 2018.11) without much success for the reboot from NAND). The re-boot process stops at this point (from the serial console): [ OK ] Reached target Shutdown. [ 152.452083] reboot: Restarting system U-Boot SPL 2019.10-armbian (Jan 25 2020 - 19:56:27 +0100) DRAM:…

Hi, I'm using a cubietruck and bananapi board (both A20 devices) for a long time (They run very stable for many years). I'm using uart3 for interfacing with arduino boards using the kernel overlay. When I upgrade the kernel to a version 5+ the overlay does not work anymore and ttyS3 is not working and missing in dmesg. The behaviour is the same on both boards. Autoboot in 1 seconds, press <Space> to stop switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 3708 bytes read in 34 ms (106.4 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 217 bytes read in …

Hello If I would like to build a specific Kernel (5.1.15-sunxi64) that I have already made before and just want to add some patches to the kernel, what is the right command? ./compile.sh BOARD=bananapim64 BRANCH=5.1.15y RELEASE=bionic BUILD_MINIMAL=no BUILD_DESKTOP=no KERNEL_ONLY=no KERNEL_CONFIGURE=no INSTALL_HEADERS=yes

I want to drive 2 SPI devices on my orangepi zero. I enabled `spi-spidev` and `spi-add-cs1` overlays and set `param_spidev_spi_bus` to 1. But by I still get only `/dev/spi1.0` available. When I add `param_spidev_spi_cs=1`, I get `/dev/spi1.1` but `/dev/spi1.0` disappears. Do I see it correctly that I can choose *either* `/dev/spi1.0` *or* `/dev/spi1.1` but not both with that overlay? How can I activate both cs pins? There are a bunch of example custom files out there, but none are meant specifically for the setup where I need spi1 (instead of spi0) and need to use a GPIO pin for cs1. And I can't really find any docs on how to write my own overlay. So any help is appr…

Hi, I have recently installed latest (20) Armbian Desktop for OPi PC(+), have problems installing software from network repo (synaptic). 1). Small version problem with one of Qt5 libraries (dependency for Kadu - Polish communicator GG client), synaptic wants version 1u1, on the net there is version 1u3. Installed using wget + dpkg, now Kadu starts (at least) OK. 2). PostgreSQL problem: there is version 11 of PgSQL provided, OK, it's current production. BUT there is PgAdmin3(!) in repo, which works with at most version 9.6 of PgSQL (from PgAdmin site). Now there is PgAdmin4, but (I) cannot make it work (compile from source OK, but doesn't start)., there is N…

Hi Can I setup A64 cpu frequency in bananapiM64 (images taken from pine64 classic ) at 1150MHZ? Now is 1010Mhz. Armbian 19.11.3 Pine64 Bionic current kernel 5.3.9. I have solid fan and this frequency is low.

Hello It is funny that new kernels going out and kill what developers have made working on older kernels.. For example I have had no issues with GPIOs pull up in 5.1.15-sunxi64 kernel. On Kernel 5.1.15-sunxi64 I do not get those errors; Python: GPIO.add_event_detect(31, GPIO.RISING, callback=count1) RuntimeError: Failed to add edge detection I didnt have any issues with Kernel 5.1.15 but I cannot recreate it anymore. Maybe this will help to give a clue of what is happening: at 5.1.15 kernel: In ArmbianEnv.text I have enabled the w1-gpio: param_w1_pin=PC7 (PC7 Is GPIO-71) …

I've read this and it surprised me noone mentioned e2image. I'm using armbian orange pi pc build. The fs is stock ext4 hence why I stick to e2image below. It is not about cloning a live system, hence the sdcard is plugged into my PC. Fdisk shows a single partition at 4M offset. First I backup the partition table and bootloader dd if=/dev/sdX of=offset0.img bs=4M count=1 Next I backup the single partition with e2image into a qcow2 image e2image -Qa /dev/sdX1 part0.qcow2 qcow2 only keeps used blocks. My partition size is 14.7G, space taken is 12%. part0.qcow2 file is 1.7G. Done with backup…

I am successfully using Armbian Current on my Banana Pi. I have a 120GB usb SSD drive. I'd like to boot from it - my other Banana Pi with the same system boots from SATA connected HDD no problem. When I boot the device, I can see the drive using sudo fdisk -l as /dev/sda1 I can also get the UUID and everything. I've modified the /boot/armbianEnv.txt file and changed the UUID, but I can't get the machine to boot. I tried also to change the UUID to /dev/sda1. Didn't help either. When I boot with HDMI connected, I can see the kernel iterating through USB bus and the result is "no USB storage device found" and that's it. …

Hi, I have Orange Pi Zero v1.5 with Armbian Buster (mainline kernel 5.4.y) and I would like to use the serial_rs485 struct from user-level. It is possible?

Hi there. I've got the problem with boot from emmc when empty SD card is installed. Opi PC+ Armbian (debian 9 stretch) Kernel 5.4.20-sunxi I've moved OS from SD to emmc using armbian-config util, then format SD with fat and now when I power on my OPi without SD card all is ok, but when SD installed boot get stuck with error "Script failed", unknown device... I've tried to chang mmc0‘s sdc_detmode, but doesn't have /boot/script.bin Can anyone help? Thank you. Spoiler

Hi there, i need some help with using the UART1 pins 8 & 9. I own a Duo with Ubuntu 16.04.6 I've installed a software that is able to send codes over the UART1 pins to my smart home system. The software is 'active (running)' but has no connection via UART1. UART1 is enabled(npi-config) but i does not work. WiringNP is required for my software and installed. Is there any point i've missed? Did i have to switch UART1 pins to in- and output? One error i get: Service Control Manager on computer xx.x.x.xx cannot be opened. You may not have permission to do this. PS: These pins must work, i rebuild an…

Hey, i hope this has not been answered already but i could not find it. I also hope this is the right place to report it. The orange pi + does not appear in the list of devices https://www.armbian.com/download/?tx_maker=xunlong but there is a download page for it you can reach by the search. https://www.armbian.com/orange-pi-plus/ i assume its a bug in the web page?

Hello all, If i detach battery all works ok. With attached battery system reboots instead of shutting down. Anyone experiencing this issue again with 5.4.21 kernel? Is there a workaround to solve it, maybe in u-boot or somewhere else? Armbian 20.05.0-trunk built from source Thank you

Hi everyone, I am using an OrangePi Zero with AllWinner H2+ and I need to catch UART1_TX and UART1_RX interrupts. I have been reading the Allwinner H2+ datasheet (http://wiki.friendlyarm.com/wiki/images/0/08/Allwinner_H2%2B_Datasheet_V1.2.pdf) and I have seen that UART1 interrupts are mented on PG_EINT (section 4.22.2.46) and UART Register Description (section 8.3.5) - I have no clear which registers I should configure to detect the UART1 interrupts, and how to do it. For example, for detecting Received data available, I think I should: - Enable the ERBFI bit in UART_IER register - Check IID field in UART_IIR to de…

Hi everyone, I installed the latest version of armbian available today for cubietruck. The volume coming out of the 3.5mm jack is really low. I checked on pulseaudio and the volume is set to maximum. I'm from another distro and didn't have this problem with audio before. Could someone help me? There are other people that have the same issue? Thanks in advance.

Hello, I tried to install as instruction in this link https://github.com/stdevPavelmc/armbian-hostpot-bridge to convert my orange pi zero to a hotspot bridge, connected to LAN and wifi to my home under Pi-Hole application to block ads Howeverm after i call up the bridge ifup br0 the network is not running, i cannot connect to the PI again. Pi-Hole installed on the LAN interface. The content of the interfaces file # loopback interface auto lo iface lo inet loopback # wireless wlan0 allow-hotplug wlan0 iface wlan0 inet manual # eth0 connected to the ISP router allow-hotplug eth0 iface eth0 in…

Recently I wanted to give another try to a NanoPi NEO Plus2 but I noticed that it is marked as not supported and there is no Armbian Bionic image for it (the links in https://www.armbian.com/nanopi-neo-plus2/ return 404). So I checked about other FriendlyElec H5 boards: https://www.armbian.com/download/?tx_soc=h5&tx_maker=friendlyelec (I had to edit the URL as otherwise one cannot add multiple filters) And I picked the K1 plus as a close relative; the Bionic image seems working without any issue, I will keep testing and report back. The only minor issue that I could find so far is that htop will show 0 Mhz for all cores. I have report…

I have two NanoPi R1s, both with Armbian Buster. I want to use both as wireless access points, however the wifi seems to be problematic. It always works at first, but not anymore after updating, changing the config and rebooting. My hostapd config is the following: # # armbian hostapd configuration example # # nl80211 mode # ssid=[myssid, contains some numbers] interface=wlan0 hw_mode=g channel=6 [11 on the other one] #bridge=br0 driver=nl80211 logger_syslog=0 logger_syslog_level=0 wmm_enabled=1 wpa=2 preamble=1 wpa_psk=[random thing armbian-config generated] wpa_passphrase=[secret] wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP wpa_strict_rekey=1 wpa_dis…

I am running a relatively new install (few months) on a replaced microSD (RMA). Keep in mind this is a headless install. At random, usually after many days / weeks+ the orangepi appears to freeze. What I mean with freeze: - samba shares disconnect - sometimes SSH works till the password is submitted, then it times out - sometimes http works when I hard restart it - I always see a very high temp & in some logs I had seen some weird dates, so I set to write out date & temp and I got this beauty on the next freeze: Spoiler date: Sun Sep 30 13:27:03 2018 -- temp: 41.99 date: Sun Sep 30 13:28:…

I have installed ~$ uname -a Linux orangepioneplus 5.4.18-sunxi64 #trunk.038 aplay -l **** List of PLAYBACK Hardware Devices **** card 0: allwinnerhdmi [allwinner-hdmi], device 0: 5091000.i2s-i2s-hifi i2s-hifi-0 [5091000.i2s-i2s-hifi i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: Device [USB PnP Sound Device], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1 works good alsamixer When choosing allwinner-hdmi

Hello, The system changed to ro during update. The armbianEnv.txt file has been corrupted and is empty. I'm looking for how to create it again ... and I can't find it. Can you help? edit: I try to do it myself, but I don't know if that's all. verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay-prefix=sun7i-a20 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u edit: Overall, there were no problems at 5.3.9. During the update to 5.4.20 I broke down. The worst thing is that I'm not in the location : / edit: Search result: it's ok ?

Armbianmonitor: http://ix.io/2c7Y 5.4.20: EXT4-fs error (device mmcblk0p1): ext4_lookup:1700: inode #4950: comm rsync: casefold flag without casefold feature 5.3.9: without error fsck cannot see errors on another system For now, I came back to kernel 5.3.9

Hello All, I'm trying to set-up MCP2515 on 8mhz on orange Pi one on SPI0 running recent installed Armbian 5.9 / Linux 3.4.113-sun8i can bus support orange pi zero i was reading trough above for pi Zero and trying get the unit up and running, but no luck till now, CAN unit is modifed, so 3v3 for mcp and 5v for can tranciever, connections: pin1 3v3 power on vcc for mcp2515 pin2 5v power for cantranciever pin6 gnd pin19/PC0(GPIO Orange PI) MOSI - (MCP2515<->CAN) SI pin21/PC1(GPIO Orange PI) MISO - (MCP2515<->CAN) SO pin23/PC2(GPIO Orange PI) CLK - (MCP2515<->CAN) SCK pin24/PC3(GPIO Orange PI) CS - (…

I recently updated from very old Armbian image. The update was not smooth so I had to re-image my device with the newest version. After that USB devices cannot be detected at all. I tried USB keyboard and 3D printer (is should looks like generic serial device). Keyboard works perfectly during u-boot but stops working as soon as kernel starts. lsusb doesn't show any devices: $ lsusb -t /: Bus 09.Port 1: Dev 1, Class=root_hub, Driver=musb-hdrc/1p, 480M /: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus…

Как мне использовать встроенный микрофон? Pulseaudio

Hello I have problem with UART after some random time i have got serial8250_interrupt with dmesg log. After that my software reading/writing is broken from UART. [88124.598598] irq 42: nobody cared (try booting with the "irqpoll" option) [88124.598617] CPU: 0 PID: 10713 Comm: sas-statistics- Not tainted 5.3.7-sunxi #5.99.191031 [88124.598620] Hardware name: Allwinner sun8i Family [88124.598657] [<c010d751>] (unwind_backtrace) from [<c010a32d>] (show_stack+0x11/0x14) [88124.598674] [<c010a32d>] (show_stack) from [<c0923da9>] (dump_stack+0x69/0x78) [88124.598689] [<c0923da9>] (dump_stack) from [<c0164135>] (__report_bad_ir…

Dears, We have 4 boards Nanopi Neo2, but when we connect to energy, they don't boot, leds of net port (green and yellow ones) and internal led (red) are on all time. We tried to access via serial port (using an usb-serial adapter), but they not show any boot process. We tried some different boot images on sd card. Nothing works. All four devices are in this situation (and they are new!). There is any thing we can do?

how i can enable usb wifi on orange pi pc ?

Hello everybody! I wanted to report that I was unable to boot with the "Bionic minimal 20.02.0-rc1" image "Bionic minimal 19.11.6 current" did not work either The red onboard is led flashing nothin else works. The Bionic download link on the top of the page is dead as well. With the same board, SD-card, power supply and USB cable I had no problem so far running the "Buster 20.02.0-rc1 current" image (beside some "armbian-configuration" flaws Did not try any further debugging so far any ideas? Andreas

Hello! There is a common issue with my Orange Pi PC +. I didn't find any solution for it. When I "shutdown -t 0" my device, it continues to consume power and the chipset is warm. Is it possible to turn the power off completely through the command line? Thanks in advance!

Hi, Is there any reason why the card is only initialized as high speed SDHC on this board? On my phone, it is initialized as ultra high speed SDR104 SDHC. I'd like to know if there's anything I need to do to maximize the card's performance on this board. Thanks.

The Orange Pi Zero +2 H3 with USB hat will hard lock up on boot at "Starting Armbian Hardware Monitoring" when booting the latest (and at least one previous) available Buster (and Bullseye) images over HDMI console. Tested on multiple SD cards with the same result. (I will test with serial later, I do not have the time to remove it from the case at the moment; I figured I would post it now in case anyone had a chance to check before I could.)

Hello, I'm trying to setup and access point with an orange pi zero. Note that the internal wifi card is not used and an 802.11 ac usb key is used. Hostapd boot up fine and mobile phone can connect to AP. Howover after few second the orange pi complety stop responding and the serial console loop with these message : [ 264.167603] unexpected IRQ trap at vector 00 [ 264.171871] unexpected IRQ trap at vector 00 [ 264.176140] unexpected IRQ trap at vector 00 [ 264.180409] unexpected IRQ trap at vector 00 [ 264.184678] unexpected IRQ trap at vector 00 [ 264.188946] unexpected IRQ trap at vector 00 Any …

Hi, I am new here and searched the forums for an answer to my questions regarding the NanoPi NEO2 and NEO Plus2. Most answers I could find, but a few were left open. The NEO Plus2 is marked as WIP. Why? What do I have to expect not to work? Both boards are similarly old, from what I could find. Will the Plus2 move up to "supported" eventually or does it currently more look like the route is going towards CSC? Do common features like GPIO access, SPI, I2C ... work with current images? Do specific features where the Plus2 differs from the NEO2 like WiFi, Bluetooth, ... work? I already found out, that the second USB port should work…

Hi everyone, As the title, I would like to set the isolated cpu 3th on orange pi zero (armbian v4.19.62) I've try to follow this answer of ChrisK in the topic here And the boot.cmd file after edited as below: # DO NOT EDIT THIS FILE # # Please edit /boot/armbianEnv.txt to set supported parameters # setenv load_addr "0x44000000" setenv overlay_error "false" # default values setenv verbosity "1" setenv console "both" setenv disp_mem_reserves "off" setenv disp_mode "1920x1080p60" setenv rootfstype "ext4" setenv docker_optimizations "on" setenv devnum "0" setenv rootdev "/dev/mmcblk${devnum}p1" setenv bootargs console=ttyS0,115200 noinitrd root=/dev/m…

hello Igor, way i can`t download https://dl.armbian.com/orangepizeroplus2-h5/Bionic_current ??? can you update link?

After installing armumian-5.83 on Banana pi M64 and starting it, kernel error is output and restarted when executed from start or ansible. Spoiler k8s-work4 login: [ 20.668532] WARNING: CPU: 2 PID: 0 at lib/timerqueue.c:79 t0 [ 20.676119] Modules linked in: zstd zram brcmfmac brcmutil snd_soc_hdmi_codex [ 20.715677] CPU: 2 PID: 0 Comm: swapper/2 Tainted: G D 5.1.0-6 [ 20.723854] Hardware name: BananaPi-M64 (DT) [ 20.728121] pstate: 60000085 (nZCv daIf -PAN -UAO) [ 20.732913] pc : timerqueue_del+0x64/0x70 [ 20.736923] lr : __rem…

Had a bit of a success with HDMI audio and also video acceleration on OrangePi 3. What was needed was to apply some patches from LibreELEC, namely ones from projects/Allwinner/patches/linux/ . For HDMI audio to work you need 0004-sun4i-i2s-improvements.patch , which contains support for I2S on H6. When done right you should see in dmesg: asoc-simple-card sound: i2s-hifi <-> 5091000.i2s mapping ok Also what helped was an IRC chat that Jernej had with mirko some time ago: https://irclog.whitequark.org/linux-sunxi/2018-03-14 For video acceleration you need 0005-cedrus-improvements.patch and compile Cedrus driver. When done right you shou…

Hi folks, is there a reason behind the Olimex Micro board being listed as "SUPPORT ENDED (EOS)" on the armbian web site? Cheers, Klaus

Hi everyone, I want to have a diskless Orange Pi Win, i'm trying to get the Ethernet to work in u-boot, but it does not seem to connect at all with my router when booting, no blinking led at all (none on the Pi neither on the router), I tried différents cables, ports, searched on the web, found some "patches" on DTS file on the web for pine64... But nothing seems to work (but Ethernet works correctly when the Pi is booted on Linux). Any Idea ? Many thanks,

Hello, I have spend a lot of time trying to make it work I2C PL0/PL1 of orangepi zero plus 2 H5. I change sunxi-h3-h5.dtsi to status="okay" and i can not to see i2c PL0/PL1 only I can see others i2c. Can anybody help me to understand what I am doing bad? Spoiler r_i2c: i2c@1f02400 { compatible = "allwinner,sun6i-a31-i2c"; reg = <0x01f02400 0x400>; interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&r_i2c_pins>; clocks = <&r_ccu CLK_APB0_I2C>; resets = <&r_ccu RST_APB0_I2C&g…

fbtft_device - remove after kernel 5.4. How connect SPI TFT to Orange PI PC+ box? ------------------------------------------------------------------------ Welcome to Armbian buster with Linux 5.4.8-sunxi System load: 0.30 0.11 0.04 Up time: 1 min Memory usage: 9 % of 998MB IP: 192.168.0.106 192.168.0.104 CPU temp: 49°C Usage of /: 2% of 59G Last login: Wed Jan 15 19:37:39 2020 from 192.168.0.140 elephant@pls-home:~$ sudo modprobe fbtft_device rotate=90 name=piscreen speed=16000000 gpios=reset:2,dc:71 txbuflen=32768 fps=25 [sudo] password for elephant: modprobe: FATAL: Module fbtft_device not found…

Hi, Can someone help me on how we can set a uBoot splash screen (with a .bmp) instead of the running boot text? Need this in a OPiPC, legacy (3.4.113). Any help is welcome. Christos

Can we get 5.1 sound with hdmi on Cubietruck? Or it's not impossible? (Tried search on Google but no success)

I am looking for a working python "wiring library" for the NanoPi Air.... With pyGPIO i have limited success. Only GPIO4 seems to work. Just a quick "use this libray for python..." please. I need 3 GPIO pins (and UART1 which is working well under python...) Thank you!

Hi there. I want to use a push button on a GPIO to shutdown O Pi Zero safely. Though the acpid way runs fine on an O Pi One, I wonder if there is a way to make it work on a O Pi Zero. Please direct me if its documented somewhere already. Thanks

orange pi one h3 512mo ram didn't boot up and it stop at starting kernel this happend for both armbian version in the armbian website , i tryed also a version from the official website of orange pi one and it pass this step but show black screen .is there any image work properlly on orange pi one H3 please hekp

https://components101.com/sites/default/files/component_pin/Beaglebone-Black-Pinout.png I could not find a picture numbering the pins on an orange pi one. Up right pin by the arrow is pin1, pin below pin1 is pin2 and pin left to pin1 is pin3. http://www.orangepi.org/images/orangepione_info.jpg I want to use an orange pi one to install libreboot on a thinkpad t400's flashchip. Which of the following pins on the beaglebone black's p9 corresponds to which pins on the orange pi one? beaglebone black pin 17 -> ? 18 -> ? 21 -> ? 22 -> ? gnd -> ? 3.3v -> ? H…

Hi, I'm running the following kernel on my Orange Pi Lite: Linux lights 5.3.9-sunxi #19.11.3 SMP Mon Nov 18 18:49:43 CET 2019 armv7l GNU/Linux I'm getting the following crash in the WiFi driver (copy-pasted from dmesg) after some time (about 10 hours if I read the output correctly?). [36792.103947] ------------[ cut here ]------------ [36792.104326] WARNING: CPU: 3 PID: 1108 at drivers/net/wireless/realtek/rtl8189fs/core/rtw_mlme.c:2622 rtw_stadel_event_callback+0x41/0x1fa [8189fs] [36792.104331] Modules linked in: snd_soc_hdmi_codec snd_soc_simple_card snd_soc_simple_card_utils sun8i_codec_analog sun4i_i2s sunxi_cir sun8i_adda_pr_regmap snd_…

I'm looking for udev rules or some other way to read system LEDs without sudo. I tried https://github.com/todbot/blink1/blob/master/linux/51-blink1.rules, but I suspect it's not 100% what I need for the Duo.

According to the specs of the OP PC Plus, it only supports 32GB micro SD. My only 32GB that I have, that I was booting from on the OP PC plus eventually got corrupted, and will not boot, can't format and install armbian or anything. What are my options? Can I somehow boot from a 64GB micro sdcard, or USB from a fresh armbian image write?

Hi all! I have browsing the forum quite while but I did not a solution for my problem. I have bought the OP Zero from DX.com and it came with an expansion board which has two additional USB ports, a 3.5 mm AV socket and a built in microphone. And now I would like to use the audio socket as audio output and I want to use its microphone as well. But I headed some problems and I cannot use its audio features . I am using this kernel: Armbian_5.24_Orangepizero_Ubuntu_xenial_dev_4.9.4 I think there is no audio driver installed on this system. here are some other debug info: aplay: device_list:268: no soundcards found... arecord: device_list:268: no soundc…

Hello guys! I haven't found any helpful regarding to my problem, maybe you are more professional as me! (I'm not really!) I would like to set an ordered DHT22 temp & humidity sensor to work on this SBC. OS is : NAME="Ubuntu" VERSION="18.04.3 LTS (Bionic Beaver)" Kernel : Linux cubieboard2 5.3.9-sunxi #19.11.3 SMP Mon Nov 18 18:49:43 CET 2019 armv7l armv7l armv7l GNU/Linux I can export a pin as GPIO, and control a simple led. I've built a kernel module for DHT22 found on github : https://github.com/edwardlintw/DHT22 The main problem is, after successful GPIO export : echo 202 > /sys/class/gpio/export cat /…

Ok, so, first of all, I am a complete noob. I bought Banana Pi thinking that it is similar to Raspberry Pi's architecture but it's obviously not. I bought a 240x240 Waveshare 1.3 inch hat and I was wondering how to get it working on my Banana Pi Zero (H2+). On Raspberry Pi I can use Juj's fbcp-ili9341 driver but it's probably not compatible with Armbian, right? How do I go about it? Also, it would be nice to know how to detect buttons (that are on the hat) and convert them to key strokes. Thanks!

Thanks for providing the new Buster image (5.4.7) for Orange Pi One Plus. All the essential stuff works well, giving me new software possibilities. As a technical feedback, I'd just like to mention 1) the red light keeps shining (instead of turning green, but Armbian runs very well, anyway) 2) an attached monitor doesn't receive any signals (but I prefer SSH anyway) 3) the console keyboard layout wouldn't accept any changes (but using SSH, that doesn't make any difference now). Everything else in armbian-config worked fine. Great tool!

Basic information: Board: Orange Pi Plus 2e Image: Armbian_19.11.3_Orangepiplus2e_buster_current_5.3.9.img Issue: No sound on HDMI output There has been quite a few suggestions for this issue here and and OrangePi Plus and none works for me. Tried following: 0. sudo apt-get update && upgrade 1. Created and Changed /etc/asound.conf Version 1: pcm.!default { type hw card 1 } ctl.!default { type hw card 1 } Version 2: pcm.!default { type hw card 1 device 0 } ctl.!default {…

Hello, Since the kernel 5.3, used for ARMBIAN reached EOL: http://lkml.iu.edu/hypermail/linux/kernel/1912.2/04661.html Is there any movement to a new kernel version?

Took me over a year to isolate this bug. Randomly, I have found that /boot/armbianEnv.txt had unconsistent content. Examples: .tty1tty1LOGIN.8 ¹[fU7ttyS0tyS0LOGINusbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="Demaine_40_Grd_Rue_Chambre-BP" #psk="1234567890" psk=693d195a3bf2ab6defbcc0b54604ced4286a067996138db6dc793d8648f67d79 } usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="fabste" #psk="1234567890" psk=95342031a4b28398045e1761f9c64f8454902e80d37102e5476fa…

I installed the latest 5.4.8 Buster Desktop image on my Orange Pi +2e board but find the Mali drivers are (Utgard) missing or not loaded. I have tried to follow every possible links including (https://linux-sunxi.org/Mali_binary_driver) related to get VDPAU / VAAPI and GPU but with very little success. I want to have HW acceleration enabled for playing MPEG in full screen mode 1920x1280 resolution using mpv. The frame drops are significant. Questions: Are Mali drivers included in this build? If it is then how can I go about adding those drivers. Is there any licencing issues in adding Mali drivers to the Armbian image? Is there any chances of Lim…

Well, I have this old M1 lying around. I found use for it. However HDMI output seems to be broken and I have composite video USB dongle at my hand and it boots... but I can not do anything with it. The question becomes: How on earth can I make it "ssh login"-able from the first boot (preferably with mdns)? What should I do with the image? Auto configuration tools - as handy and nice those are - are not for this. Thanks.

Hi everybody, I need your help in setting the default values of some or all GPIO Pin, so that it will be always activated after reboot instead of deactivated like the default is today. The reason for this is that I've connected a relaisboard to some GPIO Pins that will need "1" to be deactivated . Everything works fine, I can control and work with these Pins like needed by using "1" for OFF and "0" for ON. After booting up my BPI I initialize the needed GPIO Pins via export the pins. That will create virtual directories for these Pins with these defaults: direction -> in value -> 0 Like I mentioned, my relaiseboard need a logica…

Hello, I have a Orange Pi One Plus and i install Armbian image but the ethernet doesnt work. I dont know how fix it. I have search on other post but i cant resolve it. Thanks for your replies!

I have an early model of the 14" pinebook with the 1366x768 panel, apparently this model has invalid EDID which prevents the display working. During booting the log is full of errors like this and also a [ 10.808400] [drm:anx_aux_transfer [analogix_dp_i2c]] *ERROR* Failed to wait for AUX channel (status: 02) [ 10.816392] [drm:anx_aux_transfer [analogix_dp_i2c]] *ERROR* Failed to wait for AUX channel (status: 02) [ 10.816409] [drm:anx6345_bridge_enable [analogix_anx6345]] *ERROR* Failed to power up DisplayPort link: -110 [ 10.816415] [drm:anx6345_bridge_enable [analogix_anx6345]] *ERROR* Failed transmitter initialization: -110 [ 10.816420] [drm:an…

today I compiled a image for my OPi One: Armbian Buster with Linux 5.4.2-sunxi package bsp-kernel[19.11.3.342] u-boot[19.11.3] dtb[19.11.3.342] firmware[19.11.3] config[19.11.3] branch[dev] but mpg123 is playing a 128kb/s Radio-Stream much too fast via HDMI (hw:0,0) - streaming the same URL via a USB-Audio-Dongle (hw:1,0) has the right speed Spoiler root@opi-one(192.168.6.114):/toshiba/iradio/stations# more ./MP3_SAW_80s http://saw-de-hz-fal-stream10-cluster01.radiohost.de/saw-80er_128 root@opi-one(192.168.6.114):/toshiba/iradio/stations# mpg123 -v -b 2048 -a hw:1,0 -@ ./MP3_SAW_80s High Performance …

Hi... im trying to find some post thtat explains if i can get armbian installed on 2m SPI and what is the effect that it causes.. my device is Orange pi win plus... Thx a lot..

I was struggling to make SPH0645 I2S microphone to work with H3 mainline kernel (4.14.87), on NanoPi Neo Core. After weeks of distress, I finally made it work! Maybe some will find it useful. Here's what I did: 1- In file sound/soc/sunxi/sun4i-i2s.c, change the following line { SUN8I_I2S_RX_CHAN_SEL_REG, 0x00000000 } to { SUN8I_I2S_RX_CHAN_SEL_REG, 0x00001000 } You may have to download the linux-source package for your kernel version, or you can build your own kernel. It's weird that in legacy kernel, this register was assigned 0x00001000 by default (and the mic worked easily on that kernel). Not sure why it's changed. I'm not …

Hi, I am facing an i2c problem on orange pi 3. The i2c0 is enabled in armbian-config. The i2cdetect output is correct, as I know my two slave boards connecting to gpio pin3 (SDA) and pin5(SCL) have the addresses 0x20 and 0x23. pi@orangepi3:~$ sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: 20 -- -- 23 -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -…

Hello Ones again I need Your advice for steering RGB LED APA106. I try to search for any program to control this Led but most of them is for RPI and it`s not work for My OPI. Is this connection for DIN should by for any SPI1?: Do You have idea how to for example set change color of led ? Regards

http://www.fsfla.org/ikiwiki/selibre/linux-libre/ I expect this is the software. Free software is software you may use, share, modify and redistribute. To my knowledge orange pi one has an armv7 cpu. And the gpu is the same as on a pinephone. On this forum I was told command apt purge iozone3 armbian-firmware might turn armbian into a free software system. There is an armv7 libre linux kernel, which to some extend supports mali gpus. I want to test the libre linux kernel on an orange pi one computer, to get to know how well a Mali 400 MP2 runs on free software. Maybe it can give a streak of how well the pinephone's …

Hello, a few Days ago, i make a new installation on a new SD Card of Buster from here https://www.armbian.com/cubietruck/ on my Cubietruck. Everythink looks fine and run well, but now i have sometimes no connection over ssh to my Cubietruck and the only Think that helps, is to pull the Power Cuble. After i plug it again, everything runs fine a time long..... What can this be? What can i do? Thank you

Hello few day ago I install one again ARMBIAN in my OPI WIN PLUS this version https://dl.armbian.com/_old/orangepiwin/archive/Armbian_19.11.4_Orangepiwin_bionic_current_5.3.13_desktop.img.gz When I was typing armbian-config The loading config setting was missing sudo apt-get install armbian-config and after install. when I login via putty I see screen like below before that I don`t have any main screen Could You advice what`s heppen (when I was first install those image (.5.3.13_desktop.img.gz) I`m remember the OPI WIN screen.

Hello, a few months ago I wrote a tutorial to enable the 7" touch display for Banan Pi and Banana Pi Pro. Unfortunately the files (*.dts e.g. sun7i-a20-bananapro.dts) have changed and I don't know how to integrate the patches in the current armbian version. Does anybody know how to do it? Is there already a overlay to enable it? Thanks. Steffen

I try connect 3.5' LCD screen, but i have error ---------------------------- Jan 4 12:24:38 pls-home kernel: [ 54.977794] fbtft: module is from the staging directory, the quality is unknown, you have been warned. Jan 4 12:24:38 pls-home kernel: [ 54.981924] fbtft_device: module is from the staging directory, the quality is unknown, you have been warned. Jan 4 12:24:38 pls-home kernel: [ 54.982417] fbtft_device: unknown parameter 'gpios' ignored Jan 4 12:24:38 pls-home kernel: [ 54.982696] spidev spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 Jan 4 12:24:38 pls-home kernel: [ 54.982947] spidev spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 …

Is anyone still working with cubietruck? I installed the latest mainline image over Christmas expecting it to have the cedrus driver but apparently it does not. I thought that everything except HDMI audio should be working in mainline now. So I installed the latest legacy image. It plays videos well but bluetooth doesnt work. I switched it on in armbian-config and 'rfkill list' shows it as not disabled but the bluetooth manager shows no adapter and search is grayed out. This is a regression as it used to work to some extent. Also, very importantly for me, neither image switch over to battery power when the AC goes out. This also used to work on leg…

I noticed with the latest bionic image on the Duo it does a soft shutdown when you use the built in button. The problem is I use this button for my own uses. Can this feature be disabled and relinquish control of the button? gpioinfo | grep k1 line 3: unnamed "k1" input active-low [used]

Hello Today my system was suspended after 5 times hit power button OPI was turn oFF After turn on, can`t connect to Network by eth0 or any WI FI. I have no idea whats happen I swap the wire but Led on eth connector in OPI yellow/green is blinking. Restart router and is the same What I should do?

Hi, as a newbie in this forum, I see a lot about HW, but almost nothing about OS Versions? Puzzled, where to place, I try to do this here: After installing Debian Buster & XFCE on an OPI-Zero, I'm getting frquently installation errors. Its always dpkg: unrecoverable fatal error, aborting: files list file for package 'xfce4-timer-plugin' is missing final newline E: Sub-process /usr/bin/dpkg returned an error code (2) like this one: ┌────────────────────────────────────────────────────────────────────┐ │ • MobaXterm 9.4 • │ │ (SSH client, X-…

After few hours wlan0 lost connection for unknown reason (reason=0) and then it looks like some kernel module crash. Is it driver problem? Any suggestion will be very appreciated! Dec 31 19:22:05 tns_3np wpa_supplicant[1097]: wlan0: CTRL-EVENT-DISCONNECTED bssid=40:b0:76:58:52:d8 reason=0 locally_generated=1 Dec 31 19:22:05 tns_3np wpa_supplicant[1097]: p2p-dev-wlan0: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD Dec 31 19:22:05 tns_3np wpa_supplicant[1097]: p2p-dev-wlan0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=CZ Dec 31 19:22:05 tns_3np NetworkManager[812]: <info> [1577816525.4151] device (wlan0): supplicant interface …

Armbianmonitor for 5.4.6: http://ix.io/260C From switching between 4.19.x and 5.4.x kernels I noticed that the lower cpu frequencies got missing. It should start at 120MHz like this: root@horangepione:~# uname -a Linux honeypot2 4.19.84-sunxi #19.11.3 SMP Mon Nov 18 18:39:42 CET 2019 armv7l GNU/Linux root@horangepione:~# cpufreq-info -o minimum CPU frequency - maximum CPU frequency - governor CPU 0 120000 kHz ( 11 %) - 1008000 kHz (100 %) - ondemand CPU 1 120000 kHz ( 11 %) - 1008000 kHz (100 %) - ondemand CPU 2 120000 kHz ( 11 %) - 1008000 kHz (100 %) - ondemand CPU 3 120000 kHz ( 11…

I'm trying to send a music from my NAS on the base of Cuibetruck (Allwinner Tech SOC A20 ARM Cortex-A7 Dual-Core T) Ubuntu Xenial with Armbian Linux 3.4.113-sun7i with bluealsa to my bluetoothreceiver connected to speakers. My working configs are in my answer to the question: https://askubuntu.com/questions/1197072/sending-audio-to-bluetooth-speaker-with-bluealsa Anyway when I play mp3 with mpd or wav with aplay the music is extremely stuttering. Question on bluealsa Github (https://github.com/Arkq/bluez-alsa/issues/279) ended with advice to check UART set up (which is already too complicated for me). My question is anybody managed to setup a nice and smooth audio ou…

Hi, I'm running a NEO2 with Ubuntu at a remote location, so watchdog would be very important to have. Didn't use it before, but afaik H5 SoC supports hardware watchdog. How should I turn it on and do I need to install and configure anything? I read about H3, but not sure about H5. Thanks!

Hello all, Recently, I bought an Orange Pi Win Plus board and have installed Armbian on SDcard and it works fine but when i try to install it on emmc using "sudo nand-sata-install" it just shows "install/update the bootloader on SD/eMMC" in the options instead of "boot from eMMC - system on eMMC" as i have seen on the internet . so guys! what am i doing wrong!? Regards,

Previously worked, but not now. I am stuck in the login line and cannot login with the keyboard from the putty screen. I cant login with keyboard on USB2. Also HDMI not working. HDMI previously worked too. I am newbie. Thanks in advance. I cant remember which version loaded on the eMMC. U-Boot SPL 2019.04-armbian (Jul 06 2019 - 20:55:41 +0200) DRAM: 2048 MiB Trying to boot from MMC2 NOTICE: BL31: v2.1(debug):bb2d778-dirty NOTICE: BL31: Built : 20:55:33, Jul 6 2019 NOTICE: BL31: Detected Allwinner H6 SoC (1728) NOTICE: BL31: Found U-Boot DTB at 0xc079e78, model: OrangePi 3 INFO: ARM GICv2 driver initialized NOTICE: PMIC: …

Hello everyone, Apologies if this is not the right forum for this questions, but could not find any more appropriate one after some searching. I get an HTTP 404 when I try to access the pre-built images for the nanopi m1 plus from the board page. I know the board is EOS but for other EOS boards I can still download the images. Is there any reason why this board seems to have disappeared completely ?

Hello Ones again I`m would like to connect 1 LED to GPIO and make it blink . I try to find tutorial on Wen but for OPI Win it`s not work (duo to lack tutorial for this models) Could You help me wrote simple code to make LED start blinking? With program included in Armbian to steering GPIO for my OPI Thanks in advance.

Hello. I'm writing a program that requires sound.target. I was reading about sound.target and how it's a special systemd unit that doesn't load until the system finds the sound card. Armbian takes quite a bit of time to find the sound card on the OPi, around 30 seconds. Or, maybe it's something else that's making it take so long. I was wondering if there was a way I could mess around with systemd or something else to make the sound card found faster, thus sound.target and my program loading faster upon powering on the device. Thank you