Allwinner sunxi

Hi If i boot my cubieboard2, sometimes it's visible on network, and reachable, sometimes not at all. After that, it isn't changes. No problem with the LAN cable, i've tried two. Also the speedtest shows the maximum bandwidths in both directions (~92 mbit/sec). The system boots always, as i see from logs. Here is from the log: sudo cat /var/log/messages | grep ether Feb 23 09:14:43 localhost kernel: [ 2.059648] sun7i-dwmac 1c50000.ethernet: PTP uses main clock Feb 23 09:14:43 localhost kernel: [ 2.059661] sun7i-dwmac 1c50000.ethernet: no reset control found Feb 23 09:14:43 localhost kernel: [ 2.059690] sun7i-dwmac 1c50000.e…

Hi, after I made a software-update for my Cubitruck last week, my VGA monitor shows text only up to "starting kernel", then turns black. HDMI still works. I tried to reinstall the newest versions of both Ubuntu Bionic and Debian Stretch, both show this problem. The old VGA monitor is used only for maintenance work on my home server and off most of the time, it would be a shame if I had to buy a new HDMI monitor for this purpose. What is going on? Thanks Engelbert

Hi, I just got my hands on a Orange Pi Zero, but when I try to use iscsiadm I get the following message: iscsiadm: iSCSI driver tcp is not loaded. Load the module then retry the command. iscsiadm: Could not perform SendTargets discovery: iSCSI driver not found. Please make sure it is loaded, and retry the operation I have tried to load the module using modprobe, but it does not seem to exist. Any tips?

I downloaded Armbian_5.59_Orangepizero_Ubuntu_xenial_default_3.4.113.img, and am running it with a 16GB SD card. I am trying to modify the I2C settings, however, when I type `armbian-config`, and select `System`, there is no "Hardware" menu option. This contradicts the documentation: Hardware is supposed to be an option in that menu. This is the current content of the /boot/armbianEnv.txt: verbosity=1 console=both overlay_prefix=sun8i-h3 overlays=usbhost2 usbhost3 rootdev=UUID=54dfde69-e472-48dd-a099-636a963154f3 rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u

Hey. I'm trying to install octoprint on my Opi Zero +2, using the latest armbian image I found here on the site. Installation works fine, and I get the web interface up and running no problem. But I have connected power to the board on the gpio pins, and want to use the mini-usb to connect to the 3d printer. I have enabled usbhost0-3 in the hardware in armbian-config, but still it seems the printer cannot be reached. I read some older posts regarding other boards, where the solution seemed to be recompiling. Is this a necessity, and if so, could someone please point me to a walkthrough? Regards Anders

Hi, I’m curious how to boot into command line rather than the GUI desktop when booting up. I have looked at some other answers where changing the `nodm` but that file does not exist. Thanks!

Hello, it seems like there are no dts files to add support for i2s. How hard would it be to complete this task? The documentation from h6 references support for i2s, and the same in the user manual from Xunlog : http://dl.sumnic.com/download/OrangePi-One-Plus.pdf Edit:After some reading, i2s is not working for now and there's no proper driver yet. Thanks to martinayotte, SPI is working.

Hi. I want to run the desktop at a 800x600 resolution, to get better FPS at full screen gaming (HDMI screen). I fiddled with OpenGL, and it looks like I got a lot better FPS by just using glshim. Is there a known approach to getting 800x600 resolution? h3disp does not show 800x600 as an option. This is the Armbian Ubuntu Xenial image. Regards, Morten

I just downloaded Olimex Lime a64 Armbian Bionic image. when I try to boot it with my sd card, kernel panics. I am posting full log below. It didn't happen with testing release. Testing release worked perfectly for the same board. U-Boot SPL 2018.11-rc3-armbian (Feb 08 2019 - 10:25:08 +0100) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000) NOTICE: Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):c9f55c0 NOTICE: BL3-1: Built : 10:25:02, Feb 8 2019 NOTICE: DT: sun50i-a64-olinuxino INFO: Configuring AXP PMIC INFO: PMIC: DRAM voltage: 1.36V INFO: PMIC: setup successful NOTICE: SCPI: dum…

Hi there, after a recent apt upgrade I have problem with WiFi. I CAN connect to one WiFi, WPA2, static IP. However I CAN'T connect to another one, WPA2, tried with static and dynamic IP. I am using NetworkManager. Searched forum, deleted /etc/networks/interfaces. Information in /etc/NetworkManager/"network name" seems to be correct. Almost the same as for working net. (except uuid & IP info) CAN also connect from laptop. wpa_supplicant line from ps: /sbin/wpa_supplicant -u -s -O /run/wpa_supplicant What should I check else?

Hello, I installed last Bionic on a Orange Pi PC+. It's on EMMC. (it used to have an old Armbian Ubuntu with 3.x kernel before) Common settings (background image, GTK theme, icons, panel) are there on logout but are not saved on reboot. I saved a text file in the home user folder, it's OK. With another common user I face the same problem, with the root account settings are saved. My Linux knowledge is average, I really don't know what's wrong. Thank you Mathieu

Hello, since I upraded from Armbian Strech 5.60 (kernel 4.14.84-sunxi) to Armbian Stretch 5.70 (kernel 4.19.13-sunxi), I can't get hostapd to work on my Cubietruck. When I modprobe the brcmfmac module, I get the following lines with dmesg: [134591.243266] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip BCM43362/1 [134591.523515] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip BCM43362/1 [134591.523658] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43362-sdio.clm_blob failed with error -2 [134591.523665] brcmfmac mmc1:0001:1: Falling back to syfs fallback for: brcm/brcmfmac43362-…

Orange Pi PC+ installed Armbian Bionic mainline kernel 4.19.y, Armbian Stretch mainline kernel 4.19.y not working sound via HDMI, on an older version Armbian Xenial desktop legacy kernel 3.4.y sound via HDMI works. What to do to make the sound work in the new version

Hi Has anyone got the on board Bluetooth going on their OP Prime ?

hi freinds i'm trying to use a dht22 to read temperature and humidity , with Armbian 5.65 (stretch) 4.14.78-sunxi and orenge pi zero orange pi state like this /etc/modules-load.d/modules.conf #gpio sunxi #gc2035 wire wl-sunxi wl-gpio wl-therm #sunxi-cir #xradio_wlan g_serial #xradio_wlan i2c -dev /etc/default/cpufrequtils ENABLE=true MIN SPEED=6000000 MAX_SPEED=1200000 GOVERNOR=interactive /boot/armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay prefix=sun8i-h3 overlays=usbhost2 usbhost3 12c0 wl-gpio rootdev=WID=55cee3e8-79d6-4dd3-ab14-99274fo626cb rootfstype=ext4 param…

Dear Armbian Friends, My temperature sensor is not detected by board. Can somebody give me some advice what should I chceck / change / test now? Cheers! Lucas I tried: - another sample of DHT11 - changed cables to different ones - changed - both tested sensors were connected with 4.7k resistor between positive and data cable - tried different system versions like bionic, stretch and now jessie - tried to load modules via /etc/modules-load.d/modules.conf g_serial w1-sunxi w1-gpio w1-therm - or with /boot/armbianEnv.txt (disabling loading with modules.conf) wverbosity=1 logo=disabled co…

Hello! In this topic: It was confirmed that more than 1 pin GPIO can be used for 1-wire bus. How can I edit or create my sun8i-h3-w1-gpio.dts for this? Spoiler /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&pio>; __overlay__ { w1_pins: w1_pins { pins = "PD14"; function = "gpio_in"; }; …

Hello. When my orange pi zero is booted, Pin16,18(PA19,PA18) seems to record high value(3.3v) I want the pins to stay low. In the dtb file, PA18 and PA19 are assigned to i2c1 and i2s0. But in the /boot/armbianEnv.txt file those overlays are not enabled. Can someone please help me how to keep ping 16 and 18 low at t he boot time? Image used: ARMBIAN 5.38 stable Ubuntu 16.04.4 LTS 4.14.18-sunxi Thank You.

Seems like it won't boot and stucks at: INFO: PMIC: DRAM voltage: 1.50V INFO: Continiously reboot. Can't understand why. Any advice?

Hi, I am trying to install the aircrack-ng driver via dkms from over here: https://github.com/aircrack-ng/rtl8812au When I change the Makefile to match my processor arm-sun50iw1p1 , I receive these compilation errors and do not know how to fix them. cat /var/lib/dkms/rtl8812au/5.2.20.2/build/make.log DKMS make.log for rtl8812au-5.2.20.2 for kernel 4.19.20-sunxi64 (aarch64) Tue Feb 12 21:53:55 UTC 2019 make ARCH=arm64 CROSS_COMPILE=/home/android_sdk/Allwinner/a64/android-51/lichee/out/sun50iw1p1/android/common/buildroot/external-toolchain/bin/aarch64-linux-gnu- -C /lib/modules/4.19.20-sunxi64/build M=/var/lib/dkms/rtl8812au/5.2.20.2/build …

When the system call # /sbin/fstrim --all the process enters intermittent sleep, and all the following processes gradually obtain the same state. In crontab it appears as a task of the # fstrim -v / system, the same command if I do it manually also has the same result of never ending and blocking the other processes little by little until the system is totally blocked. Can it be disabled? As a check that is compatible with the microsd? Any recommendation?

Hello, as already described in this topic: https://forum.armbian.com/topic/5619-nanopi-duo-sound-delay/ I have the same problem with delayed audio. -> " if I run speaker-test -t wav, instead of the sound playing "front left" it just play the work left, the continues playing "front left" correctly." When I run an audio-output-command two times, the audio is played well with the second command. But the greater problem in my case is a loud cracking noise when audio stops. Is there anyway to prevent the shutdown of the amplifier? I have to repeatingly start and stop audio files from nodejs. Thanks for your help, Jimmy

Hello, I don't know if this is board related or probably armbian related... anyway. In my old banana pi (4.19.13-sunxi) htop (version 2.1.1) is like this: While on every other linux PC, server or whatever I have it looks like: The small and stupid difference is in those blue "tree view" lines (under the Command column), which I don't really like nor understand. Is there a way to set those lines as they normally should be? (and why was it set???) Thanks

Hello, did anyone manage to get Teamviewer host working on Orange Pi PC (H3) and Armbian? It installs ok, i can start the program but i cannot login to my account and when i set permanent password it shows No Connection and i cannot see the ID. Thanks!

Hello, I am new to Orange PI and Armbian. I try to configure orange pi to run chineese LCD 5 inch screen via HDMI. I managed to do that using lubuntu downloaded from orangepi server. I changed fex file to what I found on the internet: [clock] pll_video = 321 [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 3 screen0_output_mode = 2 screen1_output_type = 3 screen1_output_mode = 2 fb0_width = 720 fb0_height = 480 fb0_scaler_mode_enable = 1 fb0_pixel_sequence = 2 fb0_format = 4 fb0_framebuffer_num = 2 fb1_width = 720 fb1_height = 480 fb1_scaler_mode_enable = 1 fb1_pixel_sequen…

hi there,the 4.19 kernel on win plus is great to play with but it really takes hours to boot. it stucks at starting kernel step. any advice?

Hi, i am running armbian stretch on an OrangePi PC with "-dev" kernel and uboot. This was originally an jessie installation with legacy kernel, that was upgraded. I'm wondering now, why the cpu frequency only scales between 648 and 1008 MHz instead of 408 and 1296 MHz. Is this to be expected? cpufrequtils is configured to the latter. # lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0-3 Thread(s) per core: 1 Core(s) per socket: 4 Socket(s): 1 Model: 5 Model name: ARMv7 Processor rev 5 (v7l) CPU max MHz: 1008,0000 CPU min MHz: …

Hello together, i opened a ticket here https://github.com/armbian/build/issues/1085 Why "cat /proc/cpuinfo" does not tell anything about the CPU type?

Hi there, I am using Workstation edition on OPi PC+, system quite up to date. Problem: wired ethernet looks hardwired to DHCP (client) and I want to use static address(es). There is Network Monitor but I can't edit / delete "ifupdown(eth0)" connection. I can create another connection for wired eth in NM, static address, but it does not go active on system startup. I can switch off "eth0" and activate another connection from NM desktop, but I want system to start automatically with static IP (w/o user action).

board in WIFI mode phy#0 Interface wlan-ap ifindex 3 wdev 0x1 addr 02:81:1d:98:1c:bc ssid tomesh-8583 type AP txpower 12.00 dBm Drivers seems to crash as soon as i try to associate the first device with it Any one know what could be causing it? hostapd.conf interface=wlan-ap hw_mode=g channel=11 auth_algs=1 wpa=2 wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ssid=tomesh-8583 wpa_passphrase=password123456 [ 40.084416] Unable to handle kernel paging request at virtual address e1f27e64 [ 40.091697] pgd = 1…

I did the following upgrades this morning libcurl3:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), libgd3:armhf (2.2.4-2+deb9u3, 2.2.4-2+deb9u4), armbian-config:armhf (5.72, 5.74), linux-headers-next-sunxi:armhf (5.70, 5.73), linux-image-next-sunxi:armhf (5.70, 5.73), curl:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), libcurl3-gnutls:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), linux-dtb-next-sunxi:armhf (5.70, 5.73), base-files:armhf (9.9+deb9u6, 9.9+deb9u7) and found my I2C bus not working anymore. I did a scan on the 4 buses (Olinuxino Micro A20) and found a device on i2c-1 instead of i2c-0, changed my settings and all worked again, so I guess one of the updates must…

Hallo, i have an old istallation of armbian and it's working perfect , thank you Igor for your work..! i want to upgrade my stable debian wheezy without breaking nothing :p the current version of armbian is : Linux cubietruck 3.4.104-sunxi #1 SMP PREEMPT Fri Oct 17 16:13:30 CEST 2014 armv7l GNU/Linux and the : /etc/apt/sources.list deb http://ftp.it.debian.org/debian wheezy main contrib non-free deb-src http://ftp.it.debian.org/debian wheezy main contrib non-free deb http://ftp.debian.org/debian/ wheezy-updates main contrib non-free deb-src http://ftp.debian.org/debian/ wheezy-updates main contrib non-fre…

Hello, I'm new to the Pi computers and all that, and I'm planning on doing a project, so I was wondering if the Opi One H3 would support packet injection and monitor mode on Armbian with the onboard wifi? Thanks in advance.

Just for information, I have tested ADS7846 touchscreen on new 4.19.y Bionic Orangepi one. What I did to get it work: 1. Upgrade dtc to version 1.4.7. By default it was dtc version 1.4.5 and I have get errors while trying to do " armbian-add-overlay sun8i-h3-spi-ads7846.dts" 2. There is missing driver in kernel by default, so I have installed ubuntu bionic 18.04.1 LTS on PC. After that use this guide https://docs.armbian.com/Developer-Guide_Build-Preparation/ Switch on ADS7846 module, then install new compiled package linux-image-next-sunxi_5.74_armhf.deb on OrangePi-one.

Hi, unfortunately many times the support for XFS filesystem is just forgotton. At the moment I just run the last update for the cubietruck this morning which includes the new kernel version 4.19 and my system, which is used as an NAS device with XFS filessystem, didn't start again. I found out that this filesystem is not supported anymore (see 'cat /proc/filesystems') and no module is available. Could you plaese take care of this to fix this issue in the future? And/Or tell me please how I can get back to the older version of the kernel which supports XFS. The reason why I say this way is because I cannot spend every time hours or day's f…

I use a OPiPC as my mqtt and smb server. Until Monday I used an older version of Armbian (something around 5.20 I think) and everything worked flawlessly. Monday i did a mistake and destroyed the sd card filesystem (i was doing a backup with dd, but i've made a mistake making the sdcard as the output file). After downloading and installing the system on a new sdcard (Armbian 5.69 on a 32gb Kingston class 10 sdcard) I've experienced a few problems: --h3disp and h3consumption were missing (I've read that this is due them being incompatible with the latest kernel, which is sad because i'd like to turn off the ethernet and hdmi controllers as well as underclocking the cpu to …

Hello! I'm using Armbian Stretch for 1080P Pinebook A64. I've installed Armbian Stretch about 2 months ago, when it was still "Unsupported" and in-development. Now, however, it's supported. Currently, I'm on Armbian Stretch 5.60 and dev branch. I would like to update to 5.69 and next branch. However, from armbian-config, I'm only able to go from stable to nightly build (5.68, but still dev branch). Moreover, I can't select next kernel from Other menu. Is there a way to switch branches (barring re-flashing from latest image)?

Hello everyone. I'm new to Armbian. If I do not restart or turn off by command (correctly) all the files generated or transferred since it was turned on are deleted immediately. Why? Is it normal in Armbian? I use Orange Pi Win Plus 2, how do I deactivate that functionality? I use it as a remote server.

Problem was, that via same file /etc/rc.local was started dnsmasq which crashed and rc-local.service didn't continue with starting wvdial , Hello All, Could someone please help me to start command wvdial during booting-process? When I star wvdial command from command line, LTE USB modem is started and ppp0 interface is activated and everything works fine, but I want it to be started automatically during booting-process. I tried add wvdial to end of file /etc/rc.local, but wasn't successful. I also tried to add record to file /etc/network/interfaces as: auto ppp0 iface ppp0 inet wvdial None of these mentioned above helped.…

Hi all, I'd like to use a touch display together with my cubietruck. Research shows displays for all other boards but not for cubietruck :-( Isn't there any touch display out there which works with cubietruck? Do I really have to change system to raspberry or something else? Thanks for your help and best regards, cibomato

Hi. Simple task: connect Orange Pi Zero+ (on H5) to TV by composite (RCA). Why? Because it haven't got any other options for video (and my relatives has TVs with RCA ;-)). I find solutions for H2+ and H3, but nothing for H5 and latest Armbian. Asking for help.

Hi. Can I set small lcd screen, connected by i2c as standart output? It can be useful for console apps, which output status as text.

Banana Pi (original "model 1") A20 Was running flawlessly on Xenial - latest updates - almost everything worked (I run it on a LiPo battery to transport back and forth from work to keep my Resilio Sync data "in sync") Resilio seems to work fine - except in Bionic I can't use avahi to resolve names on my LAN... this worked in Xenial on the same hardware. The reason I decided to try out Bionic? Couldn't find a resource to upgrade from OpenSSH 7.2 to 7.3 or greater (I'm making heavy use of features not available in OpenSSH 7.2 on my other machines). I've tried tweaking my /etc/nsswitch.conf file to no avail... Sheesh - "avahi" just worked out of th…

Hello everyone, Around July 2018 I was able to successfully build an Armbian image for NanoPi Duo using provided documentation: https://docs.armbian.com/Developer-Guide_Build-Preparation/ The reason I decided to build the image was that I needed it with legacy kernel 3.4.113. For some reason there were significant problems with using the mainline kernel with direwolf application which is an amateur radio APRS modem. The device hanged with mainline kernel after few hours of operation without any reason and this was not an overheat problem (temperatures below 50 degrees and a huge heatsink). I believe that it is some problem with audio driver for H2 wh…

Hello everyone. I have installed the Armbian Xenial Multimedia and desktop usage scenarios on my orange pi pc plus. Setup user and new password successfully. By using the command armbian-config I have solved my keyboard issue and language. Also network Lan0 is ok By typing sudo apt-get update and upgrade my orange is now updated succefully. But how to start the desktop ? I can only see the black screen with prompt command. If I reboot it , after all [ok] ...... I read Ubuntu 16.04.5 LTS orangepipcplus tty1 login ...... Did I do some mistakes?

Hi, I have a quesiton/problem: How can I access the Nano Pi Neo Air with current Ambian (Stretch) OS (Armbian_5.69_Nanopiair_Debian_stretch_next_4.19.13) using USB SSH? Access to serial console is working fine, but I need SSH. How can I activate this, WLAN is no option for me due to requirements for the systems. Thank you!

Hello folks, I'm having trouble booting to Armbian. The green LED turns on, and the LAN lights work, but outputting to HDMI always ends in no signal. I have tried: - Using official Orange Pi operating systems, they work, but are unstable. - Using f3 to check if my SD card is corrupted/fake. Returns working. - Using different power bricks, will still turn on leds, but not output to HDMI - Using different Armbian kernels, no success Any ideas lads?

Hello, Hello, I have connected a pcf6523 RTC module to my OrangePI plus 2E and I can not get it to work. The i2cdetect -y 0 command gives me the following answer: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- 04 -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: 20 21 22 23 24 -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: 40 41 42 -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- -- 70: 70 -- -- -- -- -- -- -- The next thing I have to …

When trying to upgrade, I get the following error: root@orangepilite2:~# apt upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: armbian-firmware 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B/5,755 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue? [Y/n] (Reading database ... 38292 files and directories currently installed.) Preparing to unpack .../armbian-firmware_5.74.190202_all.deb ... Unpacking armbian-firmware (5.74.190202) over (5.72.190122) ... dpk…

I'm trying to figure out what happened in my device this morning. the process that i'm monitoring was interrupted and restarted and i'm want to know that reason, is it internal code reasone or system failure that caused to my process to crash. i'm attaching the /var/log/message piece of logs when my process crashed. can you tell me what happened? I'm using NanoPi2 NEO with latest armbian version for this specific board, Thanks alot Spoiler Feb 1 05:16:13 nanopi NetworkManager[642]: <info> [1548990973.1753] dhcp4 (eth0): address 10.0.0.5 Feb 1 05:16:13 nanopi NetworkManager[642]: <info> [1548990973.1822] dhcp4 (eth…

Just cancel the topic please. armbianmonitor.log.tgz

So I have a weird problem that I haven't seen yet, so forgive me if its already been answered. But for some reason mainline kernels (bionic and stretch) both bootloop at the same place. Seen below: The board boots perfectly fine on legacy kernel though. I'm using decent quality Samsung SD cards, and I've tried every combination of usb cable/powerbrick as well as the barrel jack so I'm not sure what the snag is.

Hello! The same issue was solved one year ago: Module 'nls_utf8' was missing in armbian 5.3.6 (4.13.16-sunxi64) Some time ago, the absence of a module was again discovered, without which the 'mount' with option 'iocharset=utf8' fails with error. The output of: grep -i nls_utf8 /boot/config* is # CONFIG_NLS_UTF8 is not set Please include again the module 'nls_utf8' in kernel update. Thank you very much! Denis

I have met an ethernet internal error. error log [ 2.003302] Internal error: Oops: 96000004 [#1] SMP [ 2.008184] Modules linked in: [ 2.011243] CPU: 1 PID: 33 Comm: kworker/1:1 Not tainted 4.19.12-sunxi64 #5.68 [ 2.018458] Hardware name: Orange Pi One+ (DT) [ 2.022909] Workqueue: events deferred_probe_work_func [ 2.028045] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 2.032837] pc : sun8i_dwmac_probe+0x16c/0x550 [ 2.037277] lr : sun8i_dwmac_probe+0x21c/0x550 [ 2.041715] sp : ffff000009273b00 [ 2.045027] x29: ffff000009273b00 x28: 0000000000000000 [ 2.050337] x27: ffff000008d9eb30 x26: ffff000008c023a8 [ 2.…

Hi! Periodically, time in two-three days, sharply increases CPU utilization, the system becomes disfunctional. SD card and power supply maybe not the best, but they working fine in other systems and I'm tried others. SSH hangs on login while this problem is actual, but i have a serial connection, so can investigate in real time. Please, advise, what to look when this situation came again? top - 03:02:15 up 24855 days, 3:14, 1 user, load average: 1.75, 1.77, 1.93 Tasks: 125 total, 3 running, 70 sleeping, 0 stopped, 8 zombie %Cpu(s): 17.4 us, 26.6 sy, 0.0 ni, 56.1 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem : 505152 total, 9724 free,…

HI, I have the following NanoPi Neo 2 boards, hardware v 1.1, model 1711 with 1Gb RAM Linux 4.19.13-sunxi64 #5.70 SMP Sat Jan 12 17:41:57 CET 2019 aarch64 GNU/Linux I have noticed that various network related tasks fail at boot apparently at eth0 is not yet ready This includes network mounts via /etc/fstab and disabling IPv6 via /etc/sysctl.conf My current solution (which I feel is a complete bodge) is to have extra commands in /etc/rc.local that after a 5 second sleep issue a 'mount -a' and 'sysclt -p' I have tried solutions for 'wait for network' on boot but neither work. systemctl enable …

Board NEO2 with Armbian Stretch mainline kernel 4.19.y many errors: info:xxxxx[3087]::2019-01-30T10:19:10.607956+00:00: /usr/sbin/xxxxx: error while loading shared libraries: libsystemd.so.0: cannot open shared object file: No such file or directory info:xxxxx[3093]::2019-01-30T10:19:20.857869+00:00: /usr/sbin/xxxxx: error while loading shared libraries: libsystemd.so.0: cannot open shared object file: No such file or directory info:xxxxx[3097]::2019-01-30T10:19:31.114980+00:00: /usr/sbin/xxxxx: error while loading shared libraries: libsystemd.so.0: cannot open shared object file: No such file or directory info:xxxxx[3106]::2019-01-30T10:19:41.3579…

Hi, Since the armbian release 5.3.6 (Linux 8 jessie 4.13.16-sunxi64) does not contain the module 'nls_utf8', one can not use the OpenMediaVault - OMV - plugin 'Remote Mount' for accessing an external HDD ... for example, which is connected to a Fritz!Box (running Fritz!NAS). Further details please see OMV - Remote Mount: How to mount an HDD that is connected to a Fritz!Box 7490? Please include the module 'nls_utf8' (and maybe some more nls_* modules) in an update compilation, which is based on the same kernel. Many thanks in advance. The module is provided in following Debian Jessie file list (image): https://packages.debian.org/jessie/…

good day everyone, Just for fun , i try to run gpu miner on OPI win plus, with open CL. https://github.com/hominoids/sgminer-arm but i face several problems and It would be nice if some buddy could help me. I cant install all needed libs: root@orangepiwin:~# apt-get install mali-fbdev -y Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package mali-fbdev https://forum.odroid.com/viewtopic.php?f=98&t=29571 To install Download ARM Computer Vision and Machine Learning library, is that value true: usr/lib/arm_compute-v18.03-bin-linux/lib/linux-ar…

I have few of i2c devices that was successfully tested working with RPi Zero W (Tiny RTC, BME280), but no one is visible to NanoPi Neo Air board with Armbian. I can't get it to work on latest few versions of Armbian. As soon as I add i2c0 to overlays there appears two of i2c devices (both silent): $ ls -la /dev/i2c* crw-rw---- 1 root i2c 89, 0 Jan 28 14:58 /dev/i2c-0 crw-rw---- 1 root i2c 89, 1 Jan 28 14:58 /dev/i2c-1 I need to admit that scan itself took quite significant amount of time. $ sudo time i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -…

Hi, I moved from Jessie to Stretch. On Jessie i looked under a scope and generated SCK (Orange Pi Lite is Master) is clean. However, after i switch to Stretch, my SPI Slave doesn't work anymore and further investigation reviews that it has similar problem as previous builds that extra clock cycle is generated before data is transfered. The behaviour is exactly similar to following image posted by another forumer but for earlier builds. I am not sure whether any of you experience the same problem. Thanks my armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=…

Hello, I configured 2 armbian on sd card and the configuration of the i2c is the same in armbianEnv.txt. Plattform Olimex-Lime2 A20 verbosity=1 logo=disabled console=both disp_mode=1280x1024p50 overlay_prefix=sun7i-a20 rootdev=UUID=194e9f9a-826b-4644-9f2f-4ef388277816 rootfstype=ext4 overlays=i2c1 i2c2 uart3 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u as you see, I confiugred the overlays. But on one image I get: #image with desktop sudo i2cdetect -l i2c-3 i2c mv64xxx_i2c adapter I2C adapter i2c-1 i2c mv64xxx_i2c adapter I2C adapter i2c-2 i2c …

Hi, ARMBIAN 5.70 4.19.13-sunxi orangepiplus2e journalctl -xe output ... янв 26 21:58:03 orange rc.local[1356]: cat: /sys/devices/system/cpu/cpu0/online: No such file or directory янв 26 21:58:03 orange rc.local[1356]: /usr/local/bin/sun8i-corekeeper.sh: 14: [: =: unexpected operator янв 26 21:58:08 orange rc.local[1356]: cat: /sys/devices/system/cpu/cpu0/online: No such file or directory янв 26 21:58:08 orange rc.local[1356]: /usr/local/bin/sun8i-corekeeper.sh: 14: [: =: unexpected operator ... every 5 second error. root@orange:/sys/devices/system/cpu/cpu0# ls cpu_capacity cpufreq hotplug of_node power subsystem topology …

Hello everyone, I want to make up a RAID 1 array with two disk, but mdadm tells me that I can't find the md_mod module : mdadm: Note: this array has metadata at the start and may not be suitable as a boot device. If you plan to store '/boot' on this device please ensure that your boot-loader understands md/v1.x metadata, or use --metadata=0.90 Continue creating array? y modprobe: FATAL: Module md_mod not found in directory /lib/modules/4.19.13-sunxi64 mdadm: Fail create md0 when using /sys/module/md_mod/parameters/new_array mdadm: unexpected failure opening /dev/md0 I looked up the /lib/modules/4.19.13-sunxi64 directory,…

Hi, my overlays=w1-gpio spi-spidev are not working anymore since I upgraded from 4.14.84-sunxi to 4.19.13-sunxi (Banana Pi with armbian 5.70). Regarding the 1-wire protocol cat /sys/bus/w1/devices/*/w1_slave responds "No such file or directory" since the upgrade. Also regarding the spi overlay # ls /dev/spi* should result in /dev/spidev0.0 whereas kernel 4.19 says "cannot access /dev/spi*: No such file or directory". All was working fine with the 4.14 kernel. thanks in advance

Hi, I have just received some shiny new NanoPi Neo 2 boards, hardware v 1.1, model 1711 with 1Gb RAM. I have installed Armbian Stretch mainline kernel 4.19.y with no issues at all however I have noticed that the green LED is pretty well ignoring anything I ask of it. ls -la /sys/class/leds/ total 0 drwxr-xr-x 2 root root 0 Jan 25 16:14 . drwxr-xr-x 52 root root 0 Jan 1 1970 .. lrwxrwxrwx 1 root root 0 Jan 1 1970 nanopi:green:status -> ../../devices/platform/leds/leds/nanopi:green:status lrwxrwxrwx 1 root root 0 Jan 1 1970 nanopi:red:pwr -> ../../devices/platform/leds/leds/nanopi:red:pwr cat /sys/class/leds/…

Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPREQUEST(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPACK(br-lan) 192.168.1.124 02:02:04:01:61:60 volumio Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPDECLINE(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPDISCOVER(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPOFFER(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPREQUEST(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 201…

Hi, I'm trying to set up multiple wlan interfaces for my Orange Pi Zero Plus2 H5. I want to have a interface in AP mode and a interface in Managed Mode ... so that I can provide a minimal "register me into your wlan" AP and the other interface can try that provided wlan credentials without reusing/ turning off / reconfigurating the AP interface. So I want to run a normal hostapd on wlan1 and a wpa_supplicant on wlan0 ... When I'm using the iw list command, I get serveral "valid interface combination", one is * #{ managed } <=1 , #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device} <= 1, #total <= 4, #channel <= 1 afaik that me…

When I ssh to my Banana Pi (I / A20) there is a delay of a few seconds till welcome screen / prompt. With Bananian it was instant as still is with second BananaPi with Bananian and all other kind of Pis I have, rock64 with Bananian no delay also, but faster cpu off course. Tried ssh -vvvv and a look at sshd logs, didn't found something indicating an error yet.

Hi, I'm trying to interface a USB module via the usb pins (USB-DM2 and USB-DP2 - Pin 3 and 4 on the 13-pin header) and powered by the 5V and GND pin (Pin 1 and 2 on the 13-pin header) on the Orange Pi Zero board. During startup/reboot of the Orange Pi Zero, the module fails to get recognised and come up( output of lsusb and dmesg do not show any usb devices). The module, however gets recognised and works fine when plugged out and back in. Are there any extra steps that I have to take in order to make the module get recognised during bootup? Any help regarding the matter would be appreciated. Thanks in advance!

I have bought 3 OPi Lite 2 (H6 based) dev boards. Just downloaded the latest Bionic image at the following link: https://www.armbian.com/orange-pi-lite-2/ I understand it's WIP. However, it seems to have issue on booting up. I connected HDMI cable and upon boot up, I could see init info on the screen, then it says, starting Kernel ... , then screen goes no signal, power LED stays RED forever. I read that the current image seems to have issue on HDMI. But it worked with HDMI upon initial bootup, then stopped working. My problem is that without HDMI, how could I edit the WIFI config to have the board connected to my network thus to SSH into the board for fu…

I have a new OPIz running ARMBIAN 5.70 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i with Pihole version 4.1 (latest). The Opi is connected only with eth0 with a static IP address. Its running a 32G sandisk Ultra (class 10) with a verified image using Etcher. The CPU is running at around 59c. It's unusable because the OPi keeps losing connectivity. Usually about every 12-24 hours but more frequently at times (sometimes two or three times an hour). So no ping, no ssh, no telnet. Ive implemented some scripts on the OPi to try and track down what's happening. But the first thing I notice is syslog gets cleared and/or has large gaps in it. …

Hi, Orange PI Lite Armbian 5.25 (latest download available at the time of this post) ARMBIAN 5.25 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i I would like to have the Pi boot without the desktop environment, and either start it manually over SSH. I found a tutorial that said to edit /etc/default/grub and change GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" to GRUB_CMDLINE_LINUX_DEFAULT="text" but that file does not apply, so I'm not sure how to impliment this for armbian. I don't want to remove the desktop environment completely, but rather have it bootup to command line only, and if I need the desktop environment log into via SSH and either re-edit "a file" and…

Issue found! Orange PI changed eMMC from KLM8G1GETF to KLM8G1WEPD. The difference is eMMC 5.0 vs 5.1 and maybe more. The key things is that Armbian (checked using 5.35 and the latest one) does not see this memory (fdisk -l)!! I have noticed it on OPI0 Plus 2 H3. PCB boards are the same, only memory model no. difference. Someone solved it or noticed the same? Confused 🤨

Hi, Please, i am seeking for some help. Today i just did an apt-get dist-upgrade and my banana pi updated the kernel to 4.19.13. There wasnt any error messages but then i wasnt able to boot. I get messages like "/boot/zImage file not found" so i checked my sdcard (wich cointains the boot folder) and i saw that zImage was symlink to the previous kernel image (wich no longer existed). I corrected it cause in fact there was a vmlinuz-4.19.13-sunxi but there are some more symlinks broken in boot foolder. UInitrd is also broken and i dont have the appropiate file to make a new symlink, script.bin symlink is also broken (it pointed to /boot/bin/bananapi.bin wich …

I have perfectly equal Orange Pi Zero Plus 2 H3 boards in their original case - booting from eMMC. Test conditions are: WiFi Hotspot enabled, HDMI off, CPU idle, CPU governor: performance, CPU freq. 240MHz - 1.1 GHz, kernel 4.14.84 Xiaomi Mi5 Charger as psu, 2.4A usb cable armbianmonitor gives me a temp of ~50°C on one board (idle@1.1GHz) and a temp of 65°C on the other board (same conditions, CPU starts throttling here to ~960 MHz). The temp gets so high, that after an apt-get update/upgrade and reboot the opizero plus2 would not boot with an error msg that the temp is too high. The temp seems to be correct more or less, since …

Hi, I have trouble getting an IR receiver on the Orange Pi Zero+ to work. IR-Hardware: Orange Pi Zero Interface Board v 1.2 https://www.aliexpress.com/store/product/New-Orange-Pi-Zreo-Expansion-board-Interface-board-Development-board-beyond-Raspberry-Pi/1553371_32770665186.html I use Armbian 5.65 (Debian stretch), Kernel 4.14.78 I activate the IR receiver by adding "cir" to overlays in /boot/armbianEnv.txt On boot it is activated and the sunxi_cir module is loaded (and also lirc_dev, don't know why), see dmesg output: [ 5.245866] lirc_dev: IR Remote Control driver registered, major 244 [ 5.255140] IR LIRC bridge handler i…

Hi Guys, today I've Updated from "Armbian_5.67_Nanopiduo_Debian_stretch_next_4.14.90" to Armbian_5.69_Nanopiduo_Debian_stretch_next_4.19.13" now I've the follwing problem on my nanopi duo. It has Wifi onboard (XR819), but after an Update to Kernel 4.19.13-sunxi. my wifi device was lost. Before the Update the wifi device was listet as wlan0. to avoid configuration errors i also reinstalled the system. It does not work with debian or ubuntu. If i roleback to an older kernel everything works great. uname -a Linux nanopiduo 4.19.13-sunxi #5.69 SMP Wed Jan 9 16:26:48 CET 2019 armv7l armv7l armv7l GNU/Linux ifconfig -a …

Hi, i'm working on a hdmi cec driver for H3 and i'm looking for some feedback how the driver works. I have tested the driver with OrangePi PC and a Samsung TV. I have pushed my driver to github : https://github.com/jodamm/linux/tree/sun8i or here is a patch file that can be placed in userpatches for armbian toolchain. The driver can be loaded with modprobe hdmi_cec . I have modified libcec to work with this driver : https://github.com/jodamm/libcec or again a patch file for libcec.

I enabled modules, and connected DS18B20 but still haven't 28-XXX... folder in /sys/bus/w1/devices. In README.sun8i-h3-overlays written that default port is PD14 but i can't find it on my board pinout.

Hi all. In Monday i build new version of Armbian image for Orange Pi One and after this i get next error while loading: Spoiler This image contains newest version of U-Boot (2018.11). My old image build with 2018.05 U-Boot version. Loadin log of old image here: Spoiler This logs made at one PC. I am concerned that in the second case booter find 2 USB devices. but in first case - double number. Anyone can help me with problem. or better write to u-boot support. Or maybe i can build my image with oldest version u-boot...? But i dont known how make this. Thanks.

I just got a Nanopi NEO2 512MB, installed Armbian Ubuntu Bionic. It works fine, except for the DVB-T/C stick. It is affected by Kernel 4.10+ problems. I wonder if I can downgrade to an older kernel, like 4.4.0 for example, where everything works perfectly? If yes, how? There is a patch that perhaps would resolve the problem, how could I apply this patch to an of the available releases of Armbian? This patch Please, help me with this. Many thanks!

I will describe my problem with NanoPi Neo Core2: I installed the system on eMMc I installed WiringNP I installed the USB drive Everything worked, also Putty via USB I wanted to connect the external module via SPI. The module requires setting the transfer frequency to 20 MHz. I decided to look at the file sun50i-h5-nanopi-neo-core2.dtb . For this purpose, I decompiled to a file . dts . Due to late night time I made a cardinal error, that is before these activities I did not copy the file . dtb I just played on the operating system. After the power is turned off NanoPi and the next day the system is not raised. Red power LED is lit green while…

I'm trying to get TFTP support into U-Boot but it insists that 'no ethernet found'. I've added a couple of nodes to the device tree such that it has 'status = "okay" and mac-address = [00 00 00 00 00 00]; I've also added a top level alias in sun50i-h5-nanopi-k1-plus.dts (as added by @martinayotte following this thread) as below. Not sure if the U-Boot config needs changing in any way but the network components are certainly being built. Any thoughts most welcome. AATIA. aliases { serial0 = &uart0; ethernet0 = &emac; }; U-Boot dump of the loaded DTB on running system follows: => bdinfo arch_number = 0x…

Hello, I am having strange problem with Olimexino A20 Micro, Ambian 5.38, 4.14.14. After every 2-3 days standby with minor cpu usage I am getting an FS error. I have tried Armbian Ubuntu/Debian and different sd cards but this doesn't change anything. I think with previous kernel there wasn't such an issue. I've connected it to the serial port and I see: login: [381301.434449] EXT4-fs error (device mmcblk0p1): ext4_journal_check_setected aborted journal [381301.444715] EXT4-fs (mmcblk0p1): Remounting filesystem read-only [381340.727458] EXT4-fs error (device mmcblk0p1): ext4_find_entry:143621620: comm sh: reading directory lblock 0 [381494.351427] EXT4-fs e…

over year end I tried to re-set up my 2 cubietrucks , one as a a: music machine b) server. a) Pity is, Volumio is no longer available for Cubietruck - anyone has a later image than 2.118? Any other proposal? b) When trying to find a workable image for Igors selection, I figured that I run into issues with all of them. Test 1 Armbian_5.69_Cubietruck_Ubuntu_bionic_next_4.19.13.img boots initial input on hdmi,then neither on hdmi nor on VGA ???? ssh works, login as root works sudo armbian-config Boot from SD - system on hdd - works sudo apt-get update sudo apt-get upgrade boot from SD - works, but still 'headless', no …

Hi! I was using armbian 5.60 with 4.14.70 kernel and WiFi AP worked flawsessly. Today I had to rebuild my sd card, so I downloaded the latest available build Armbian Stretch mainline kernel 4.19.y I can connect to WiFi from the board, also able to setup a WiFi AP on the board. But when I try to connect to the new AP I see the following message in terminal and the connecting device fails after several seconds: Message from syslogd@localhost at Jan 17 18:20:38 ... kernel:[ 349.842020] Internal error: Oops: 96000004 [#1] SMP Message from syslogd@localhost at Jan 17 18:20:38 ... kernel:[ 350.021242] Process RTW_CMD_THREAD (pid: 607, stack limit = 0x0000000…

I'm running some stress test on the NanoPi neo2 512mb, CPU heating reached 75-76 degrees, and it's stable, the problem that I faced is that the computer changed it's IP suddenly (after 55 minutes of test running), I guess it's because of a network card reset. Did anyone face the following issue? Is it related to the stress test? Or it's another networking problem? The test I'm running is with the "stress" tool, running long time stress on 4 CPUs. In addition, does anyone have any insights regarding this device? good or bad?

Hello guys, at first I want to says thanks for the great OS that you deliver. I use it since 8 months on a bunch of nano-pi neo2's and it runs rock solid. However i rebuild from time to time the image I use from scratch in order to see that the installation is reproducable and repeatable. Today it has encountered that the installation of 'apt-get install python:armhf python-dev:armhf' failed with: # dpkg --add-architecture armhf # sudo apt-get update .... Reading package lists... Done # sudo apt-get install -y python-pip python:armhf python-dev:armhf Reading package lists... Done Building dependency tree Readin…

Good time of day fellows. How can I mount SD card to transfer data into when Armbian 3.35 Ubuntu 16.04 started from flash? Cant see SD card nor mount it. Installed USBmount and it works with USB flashes on OTG port but no with SD card. Thanks to anyone for advice. Additional info: NanoPi Air 32Gb eMMC http://sprunge.us/OLNS

We have deployed the zero for an integrated MCU on one of our products, and in rare occasions we are experience random lockups of the MCU (possibly related to overheating). Its pretty much impossible to debug this since it happens very rarely, but we are trying to mitigate all possible causes. The MCU is controlling a bigger and more expensive board and a fan. If there are internal failsafes that are being triggered by the MCU and locking it up (like temp) we want to disable as many of them as possible (we would rather have the MCU burn up than our main board). Anyone have any insights on orange pi zero OTP or OCP in kernel or uboot parameters we can disable?

Hi,guys! when I build a pthon3 script with gui and GPIO contorl.I can run it when I use terminal with sudo command. But when I used "settings->session and startup" to config this script,It can't run when my device reboot (Orange Pi PC). I try to config command like: "echo 'password'|sudo -S python3 /home/kwan/OPi_PC/u_main.py" still the same. And then I tried to edit "/etc/rc.local" file and add: "echo 'password'|sudo -S python3 /home/kwan/OPi_PC/u_main.py &" still the same. The problem is when I run the other script without GPIO config and sudo command. It can run when device reboot. So,It's ther…

hello after updating from cat /proc/version Linux version 4.14.84-sunxi (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #3 SMP Sat Dec 1 07:18:41 CET 2018 to Linux version 4.19.13-sunxi (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #5.70 SMP Sat Jan 12 15:43:21 CET 2019 my one wire thermometer stopped working - is there some additional steps needed now? I didn't change my configuration overlays=w1-gpio param_w1_pin=PB10 param_w1_pin_int_pullup=0  and now I have dmesg [ 1174.451457] w1_master_driver w1_bus_master1: Attaching one wire slav…

Can anyone suggest a command line command that would return the status of the connected HDMI monitor? Whether it is on standby or not or something that might help to determine if the display is active or not. I'm currently using Armbian Xenial on a H3 Orange Pi Zero Plus 2. Thanks

hi orangepi 2e+ with ARMBIAN 5.65 stable Ubuntu 18.04.1 LTS 4.14.84-sunxi syslog I want to mount my external hard disks with cat /etc/udev/rules.d/91-intenso.rules KERNEL=="sd?1", SUBSYSTEMS=="usb", ATTRS{serial}=="31700000000000007023", SYMLINK+="Intenso", ACTION=="add", RUN+="/bin/mount /dev/Intenso /mnt/Intenso" Normally no problem, tested with Armbian_5.65_Orangepiplus2e_Ubuntu_xenial_default_3.4.113 and Workstation PC Linux 4.15.0-43-generic #46~16.04.1-Ubuntu. With my current version, I have a problem. The udev-rule is/seem ok Spoiler orangepi@orangepiplus2e:~$ sudo udevadm test /sys/class/block/sdb1 calling: test …

with great joy we saw the new version of Armbian_5.69_Orangepipcplus_Ubuntu_bionic_next_4.19.13 for orange pi pc plus (date 9-1-2019) We were waiting for a WIFI fix, on the WPA. Wifi at the very beginning, it works properly with a WPA connection. Then, you do not want to make another WPA connection and work. Will this problem be corrected in some new version of Armbian? Thanks

I met a problem that kernel showed allwiner H6 ethernet internal error. link: It is hard to loacate what makes that error occur, I wish that kernel can show my log added to drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c. my work below: 1 Added printk to drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c, and made patch with git format-patch, move patch to userpatchs/kernel/sunxi-next. 2 run ./compile.sh to compile armbian, I am sure that patch work, have checked drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c after compile.sh completion 3 burn Armbian_5.71_Orangepioneplus_Ubuntu_bionic_next_4.19.13_desktop.img to sdca…

Hi, I am new to Orange Pi ecosystem. I have a Orange Pi PC 2 running armbian and some times raspbian. I want to use a wifi adapter to this. Since there has been many discussions on which adapter to chose and how to chose I am really confused. Please help me select a wifi adapter which could be installed easily considering that I am a rookie.

Hi, I have an orange_pi_pc installed Armbian(Debian) and enable desktop. But I want to hide mouse cursor when it start. I find "Mouse and Touchpad" setting,but I can't set mouse Default Theme. Is there someone know how to hide mouse cursor on it?

Greetings to all, Preamble: Thanks to all that have worked to make the Armbian project what it is today. It is greatly appreciated! I have done numerous hours of reading and searching (due diligence). I know I could run a benchmarks and all but that means even more delay reaching the objective. Some brief guidance from those who have gone before would save a lot of time and would be greatly appreciated. Looking at the datasheets wasn't real helpful in guesstimating optimum performance configuration - especially since there are so many other factors that have an impact. Background: My objective is to achieve a reliable, long lif…