Allwinner sunxi

Hi All, Can you please help me how can I set up OV5647 camera with Orange Pi One? Where can I find driver for it? Camera link: https://www.aliexpress.com/item/Orange-Pi-fish-eye-Camera-Night-Vision-for-Orange-Pi-PC-Zero-One-PC-Plus-Plus2/32864676943.html?spm=2114.search0604.3.26.74868de282hQoP&ws_ab_test=searchweb0_0,searchweb201602_5_10065_10068_5015215_10059_10696_100031_10084_5015115_10083_10103_451_10618_452_5015815_10304_10307_10820_10821_5015915_10302,searchweb201603_16,ppcSwitch_5&algo_expid=44e91c9c-67e1-49b9-83f3-2c2890deab01-3&algo_pvid=44e91c9c-67e1-49b9-83f3-2c2890deab01&priceBeautifyAB=0 Thanks!

I installed Armbian_5.59_Bananapipro_Ubuntu_bionic_next_4.14.65 onto my Banana Pi Pro. However, there is Internet for now. $ip address gives me the following messages: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000 link/ether 02:86:02:42:2f:4e brd ff:ff:ff:ff:ff:ff 3. wlan0: <NO…

Hello, i like to work with 1wire 18b20 sensors on my Oragne Pi one , with the latest Armbian Bionic . root@orangepione:~# uname -r 4.14.65-sunxi In this forum and in the orange pi forum, there are some instructions, but I think they are out of date. 1.edit your /etc/default/cpufrequtils After edit. $ cat /etc/default/cpufrequtils ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive 2.reboot Edited by nopnop2002 at 2017-8-5 17:10 1.edit your /etc/default/cpufrequtils After edit. $ cat /etc/default/cpufrequtils ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive 2.reboot 3.driver load sudo modprobe w1-gpio su…

Hello Community! Does anybody tried to run the .Net Core or ASP NET Core runtime package on OrangePi PC2? I was trying to install it using MS guidelines [https://www.microsoft.com/net/download/linux-package-manager/ubuntu16-04/runtime-current] but no luck. I was searching Goolge for a while, and tried bunch of common solutions related to Linux and .Net Core installation - with no luck unfortunately. I am using: OrangePI PC2 ARMBIAN 5.59.180815 nightly Ubuntu 16.04.5 LTS 4.11.1-sun50iw2

Hi everyone, I'd like to ask and confirm: is there any working HDMI method with proper resolution currently for the Pi+2E, as of 5.59? I'm asking because I have tried next, I have tried dev, and I have tried the legacy kernel. None of them gave any satisfactory result at all. Mainline Kernel 4.14 -- There is HDMI graphics, but the resolution is stuck to no more than 1024x768. I read many times that this is the case when the HDMI was not detected. Kernel 4.18 -- Same thing as for 4.14. Though, as far as I know, the 4.17 should have support for HDMI. Has HDMI for H3 really landed in 4.17, or have I read wrong all over the place? …

Hi, I am new to the Armbian. I have build the kernel for BananaPi M2+ using the instruction specified in Armbian document for Building with Vagrant. I could see the output file "linux-image-sun8i-5.59.armhf.deb" in the "output/debs" folder. Know I don't know how to download or install this file on the SD card which is running on my bananaPi M2+. Bascically I need guidance on how to transfer my kernel build image from my windows PC to the SD card which I will be using to test the Bananapi M2+ board. Any help or documents will be highly appreciated.

Hello there, I was looking at the gc2035 camera sensor for the orange pi device. I want the camera module to load as fast as possible and take pictures as fast as possible. When I use a USB camera, it takes 2-3 seconds to load the module and activate the camera, and the camera takes 2 seconds. I'm thinking of compiling the GC2035 camera statically to the linux kernel. But I'm not sure how much time decrease. What I would like to know is, how fast is the camera taking pictures and how long is the loading time of the camera modules? Can I take pictures under 200 ms with the camera triggered? The Raspifastcamd module allows …

Hi, I recently reinstalled an orange pi 2+ with Armbian Stretch mainline kernel 4: root@ted1090-7:~# uname -a Linux ted1090-7 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux I also installed it on EMMC (this way, with this u-boot-sunxi-with-spl.bin). Now this orange pi crashes every couple of days (sometimes with a couple of hours). This orange pi use to run with Armbian legacy 3.x kernel on EMMC without any issue: pi@ted1090-6 ~ $ uname -a Linux ted1090-6 3.4.113-sun8i #18 SMP PREEMPT Wed Jan 24 22:10:49 CET 2018 armv7l GNU/Linux Exactly the same applications are installed (dump1090 and dump1090-tools). T…

Hi , I have an orange pi zero . I installed armbian_5.38_Orangepizero_ubuntu_xenial_next_4.14.4 my orangepi zero. when ı use 'sudo nmtui' , it does not see wifi networks. I read many questions and answers about this issue but ı dont solve. I am waiting for your answers.

vmware 12, Ubuntu 16.04: ./compile.sh, then select WIP version, orangepi lite2, the dialog exited, and message under in terminal: Error: Expected at least 5 tokens for --menu, have 4. Use --help to list options. [ error ] ERROR in function source [ main.sh:188 ] [ error ] No kernel branch selected

Help me. Armbian view my USB-HID joy in /deb/bus/usb/xxx/xxx, and my device not work in emulator(nes, sega and etc.) I think that my joystick mast be /dev/input/jsx. I find information, that module "joydev" direct the joystick, but "lsmod" show, that "joydev" is not run. Modules "joydev.ko" and "hiddev" is absent in filesystem.

hello there! after update rpimonitor to 2.13-beta6 by Xavier Berger, can't monitor, any temperature , memory usage. But CPU freq, Sd card and network work OK. my spec : Orange pi pc + ARMBIAN 5.38 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i

Hi guys! I'd like to download the correct image for my Banana Pi M1, but I don't seem to be able to find it. I've been searching already for a bit without much luck. Is it supported? Am I missing something? Thanks!

I there im using orange pi zero for homeassisatnt and google assisatant since my card died i install this new version configured every thing but audio isn´t working! I fallowed this guide like before but no audio coming for my orange pi zer no recording either! I have activated analog audio I already have everything configured with homeassistant i don´t wanna configure all again! Can you please help me make audio work in this kernel or is impossible to do?

Hi, After running the default image with legacy kernel for a few weeks, I am now trying the run a fresh SD card with the latest build of the mainline image. However, the MAC address of my device appears to be changing after each reboot - and I am running about of ideas to fix this issue. What I've tried so far: - Edit script.bin & add MAC address in the [dynamic] section - Edit armbianEnv.txt - Define an address in /etc/network/interfaces So far, I have not been able to solve the problem. Your help is much appreciated. Any suggestions on possible fixes for the issue?

Hi there, I got some NanoPi-NEO running and need to update the kernel, modules and dtb's. With 4.18 the Ethernet does not seem to get started correctly. I noticed a change in u-boot and the newer Armbian releases have Ethernet-Support in u-boot. So my basic idea is to not just copy the kernel files but also update u-boot via dd command. I suppose there are at least 3 regions in the image: 1. the partition table which I don't want to change. 2. the u-boot configuration which I'd like to keep. 3. the u-boot runtime. So for #2 and #3 I'll need an image file. I'm trying to set-up a build environment f…

Hi all, My Armbian hangs (freeze) after 1-2 hours. Below dmesg Aug 17 19:10:39 localhost kernel: [ 1666.194984] WARNING: CPU: 0 PID: 693 at lib/iov_iter.c:695 copy_page_to_iter+0x21d/0x35c Aug 17 19:10:39 localhost kernel: [ 1666.194987] Modules linked in: tun xt_nat xt_tcpudp iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_filter snd_soc_hdmi_codec rc_cec dw_hdmi_i2s_audio dw_hdmi_cec evdev sun8i_dw_hdmi dw_hdmi cec ir_lirc_codec lirc_dev pl2303 usbserial sun4i_i2s sunxi_cir sun8i_codec_analog sun4i_gpadc_iio sun4i_codec sun4i_tcon sun8i_mixer snd_soc_simple_card snd_soc_simple_card_utils snd_soc_core snd_pcm_dmaengine snd_pc…

My NanoPi K1 Plus is using at the moment ARMBIAN 5.47 stable Debian GNU/Linux 9 (stretch) 4.14.51-sunxi64 ( https://dl.armbian.com/nanopik1plus/archive/Armbian_5.47_Nanopik1plus_Debian_stretch_next_4.14.51.7z ) In the archive at https://dl.armbian.com/nanopik1plus/archive/ is also https://dl.armbian.com/nanopik1plus/archive/Armbian_5.53_Nanopik1plus_Debian_stretch_next_4.17.9.7z Is 4.17.9 also stable? And if YES is there a simple way to update without reinstalling? I did try apt update apt upgrade and apt dist-upgrade but no 4.17.9 avail. Nightly is at https://dl.armbian.com/nanopik1plu…

Hello folks, I'm having trouble booting https://dl.armbian.com/lime-a64/Debian_stretch_next_nightly.7z as of today on my A64-OLinuXino-1G4GW. Armbian is installed on an external µSD card; the device has internal flash. Do you see, how I can fix this issue? Thanks, yanosz Log is: U-Boot 2018.05-armbian (Aug 21 2018 - 08:46:56 +0200) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Olimex A64-Olinuxino DRAM: 1 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 Loading Environment from EXT4... ** File not found /boot/boot.env ** ** Unable to read "/boot/boot.env" from mmc0:1 ** Failed (-5) In: serial Out: s…

Hi, we have problems with 5 inch display from waveshare. Can somebody help us.

Hi, I'm trying to use the popular LTE USB modem Huawei E3372s (Stick mode) with NanoPi Duo. Modem is in Network card mode - USB_Modeswitch was installed and started root@nanopiduo:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0525:a4a7 Netchip Technology, Inc. Linux-USB Serial Gadget (CDC ACM mode) Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 12d1:1506 Huawei Technologies Co., Ltd. Modem/Networkcard Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 …

Hi, my current project is about using a NanoPI M1 as a controller for a 3D printer. As such, one wants to have very tight timing on the GPIO output, with as little jitter as possible, to get smooth motion of the stepper motors. However, it is common belief that getting a fast timing with little jitter is virtually impossible to do under linux, without the help of a dedicated chip just for the IO. While that is true in general on stock kernels, it's possible to vastly improve on that front by spending a little effort. One way on ARM chips is to use the FIQ. That is an interrupt that has the highest priority, which can interrupt all other, regular interrupts. Ho…

I have a encrypted external hard drive connected via USB. I want to be able to automatically access it after boot so I made a keyfile that I put in /etc/crypttab. After updating the crypttab file I ran update-initramfs -u. But after reboot the drive is still locked. Why is this? I suspect it might be because of the order of things at boot. Maybe crypttab is called before the USB device is initialized? Any help would be appreciated. Edit: I had a incorrect crypttab that's why it didn't mount. It works now thanks!

I got that stability issues on my banana pi m1, and notice that the last kernel available on armbian still the 4.14.18. Today I also run apt upgrade on raspberry pi 3 and it installed the kernel 4.14.30 that stop the ipsec vpn working, the same as in 4.14.18 used on armbian. I feel some frustration on the latest kernel updates, and wondering if anyone have some info about the next kernel update that solve this issues. Do you advise me to change to nightly builds to get a new kernel to test? สมัครufabet Any suggestion would be greatly appreciated.

board: orange pi zero plus (CPU H5) os: power on idle current is about 0.25A。 after poweroff the currtent rise to about 0.35A 。 and got error message on console: ----------------------------------------------------------------------- [ OK ] Reached target Shutdown. [67908.295169] reboot: Power down INFO: PSCI Affinity Map: INFO: AffInst: Level 0, MPID 0x0, State ON INFO: AffInst: Level 0, MPID 0x1, State ON INFO: AffInst: Level 0, MPID 0x2, State ON INFO: AffInst: Level 0, MPID 0x3, State ON ERROR: PSCI system shutdown: still alive ... -----------------------------------------------------------…

My Pi Zero with H2+ and latest Armbian 5.35 Xenial works well, but on trying to increase the screen size I get: dk@desktop:~$ ssh dk@zero dk@zero:~$ sudo h3disp -m 1080p60 Unsupported board/kernel combination: Orange Pi Zero running 3.4.113-sun8i dk@zero:~$ Is this going to be fixed? nomachine.com's remote desktop for ARM works brilliantly Ubuntu + citadel-suite gets a mail server/chat server/+other into 337 MB - amazing!

Hello, i'm trying to make a mesh network with some Orange PI Zero devices, but ibss (adhoc) and 80211s (mesh) seem not working...with an usb wifi work fine... I have read that this device's support isn't the best, but i don't kwnow if my case is a release specific bug or these modes aren't really supported. Installed release "Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14", i have also trying dev kernel but this don't load the device... What are the really working modes and valid interface combinations? Reported info by iw list command seem not correct. Thanks for the help

Hello, in the company where I work, a nanopi M1 plus was purchased and we are developing a firmware to run on the device. In our code we need to change the settings of the active wired connection at that time, but we can not do it due to an error. If, for example, we use the following command: nmcli connection modify 'Ifupdown (eth0)' ipv4.method auto The following error message is returned. Error: failed to modify connection 'Ifupdown (eth0)': Connection is read-only The command is executed correctly if the connection is not managed by NetworkManager, so when in the file: "NetworkManager.conf" the "managed" parameter is set to false. We had to s…

Hi there, I've just got my first H3 board (OPi Zero +2) and I'm interested in learning how boot process works in detail, with a focus on Security ID features. As far I can see there's not that much documentation about S/NBROM (essentially linux-sunxi's Wiki and Allwinner-info git repo) and what's supposed to be H3's NBROM (header 1100, 1100, 1633) looks like slightly different from A10's one (from git) at first glance. Is there anyone here who has already worked on it and/or has info/symbols/pseudocode/whatever might speed up the reversing process? Thank you!

orange pi one armbian xenial When I obtained the orange pi one I installed armbian xenial. I booted the orange pi one. During boot I cannot recall if a red light flashed next to a steady green flash. The desktop worked. The orange pi one was connected to a hdmi display. Resolution 1280 x 720. I wanted to use a 1024 x 768 vga display by hdmi vga converter. The desktop would keep the 1280 x 720 resolution when displaying the desktop. I tried different things in order to get a 1024 x768 resolution. Did not work. One configuration resulted in trashing the power supply. I connected another power supply. The power suppl…

LANG=en_CN.UTF-8 I have it+SD card+usb TouchScreen+HDMI Screen which work with http://www.orangepi.org/'s image. I've downloaded https://dl.armbian.com/orangepilite2/Debian_stretch_next.7z,verified the sha256 checksum,burn SD card,verified checksum of SD card... After UBoot, nothing was displayed,but `fdisk -l /dev/sdb` changed -------------------------------- Disk /dev/sdb: 30 GiB, 32220643328 bytes, 62930944 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x16977123 Device Boot Start En…

I built Armbian_5.59_Nanopineocore2_Ubuntu_xenial_next_4.17.17.img for my board, and am trying to add an overlay dtb that describes a port expander I have on i2c2. $ sudo armbian-add-overlay ./mcp23008.dts Error: dtc does not support compiling overlays Please try to install matching kernel headers

Hi, My applications were running from eMMC when I used Kernel 3.4.113 and Orange Pi PC Plus purchased 6 months back. But on my last week purchase, armbian-config of 3.4.113 does not detect eMMC of Orange Pi PC Plus. I am told by Xunlong to use the latest kernel. This will result in huge development efforts. Are there any patches that can be applied to 3.4.113 to use my same application on latest PCB? Thanks

I usually build a new armbian full os image, apply some kernel options and have no problems booting a sopine64. The last known good version for me was: Armbian 5.51 / Kernel 4.14.54 The latest (and starting with 5.57) with Kernel 4.17.16 only seem to 'half boot' - they start up uboot but fail to load the OS and instead attempt to do a network boot over TFTP. The errors go by so fast that I can't really read it and have to resort to trying to video capture it and the monitor seems to be slow to initialize and i only see the tail end of the errors scroll by. I am sure a lot changed between 5.51 and 5.57 - I noticed a new…

I've got an Orange Pi Zero Plus running Armbian Bionic. I'm trying to add a virtual wifi interface so I can create a wifi hotspot so I can connect to it easily on remote networks. iw list shows that the adapter *should* be capable of adding an additional interface. This works on other Orange Pi boards I've got but not this one. Any ideas? root@opizero:~# iw list Wiphy phy0 max # scan SSIDs: 9 max scan IEs length: 2304 bytes max # sched scan SSIDs: 0 max # match sets: 0 max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0…

Hi all, first of all, I really like the dev-tools! I successfully developed my own Image (incl. patches etc.) and it's running great. But now I want to "burn" it to the Orange Pi's emmc directly, without using nand-sata-install ... it's necessary, because the target-image does not allow shell- and/or ssh-access (for purpose). So I flashed a "normal" armbian-image to my sd-card, copied my own image-file to the card, booted the card and wanted to 'dd' my image to /dev/mmcblk1. Everything went fine till now ... after rebooting w/o the sd-card plugged in, the loader hangs in a loop (Rebooting within 10 seconds) :/ I looked into the nand-sata-install-sc…

Hello Community, I am trying to install Docker on my Cubietruck. As a guide i used the official guide by Docker https://docs.docker.com/install/linux/docker-ce/ubuntu/#upgrade-docker-ce When I am at actual installation step I walking in this following error msg. Does anyone have a idea where to start looking ? Thx.blub474

Previously I installed legacy Armbian to an Orange Pi PC Plus device and noted down its eth0 and wlan MAC addresses. Then I installed a Mainline Armbian server image to its EMMC, updated the armbian-config to enable the desktop manager. Now I checked the MAC addresses to be completely different. Why does this happen?

Hi all After having used a lot the OPiPC2 with Armbian, I am now adding support for this board in openwrt. The first add board patch, has been merged recently in snapshot branch and works ok. For the first implementation I set the MUSB port role to host, but now my goal is to set it in OTG, making this port available for usb serial console, connecting a host PC to it. So, I built the needed support for g_serial in kernel and give a try, but I cannot make it work The host PC detects just nothing, as the OpiPC2 does not detect a USB host being connected to it Checking the dmesg I see something suspicious: [ 0.614423] sun4i-usb-phy…

Does anyone know if the Zero's on board WiFi chip XR819 can be disabled? The RJ45 is disabled by default, so there must be a way to disable the XR819 - right? Any thought appreciated.

Just bumped this one: Orange Pi Zero, stable version, legacy kernel Trying to insert Realtek WiFi dongle (8188eu in my case). Module cannot load - with this error: Peeked solution on 4pda - http://4pda.ru/forum/lofiversion/index.php?t750921-1740.html - decompiled script bin and set wifi_usbc_id = 1 - before it was set to none. Original solution has value "2", but it was just a guess, so I used "1". Module worked in parallel with original xradio. According to original poster on 4pda, this issue was seen on Orange Pi PC. Not sure, is it correct solution, but, well - it may help. Issues seen - when I try to un…

Hi. I'm running armbian on a OrangePi PC 2. This is my uname -a output: root@picard:/lib/modules# uname -a Linux picard 4.18.0-rc8-sunxi64 #30 SMP Mon Aug 13 00:57:56 CEST 2018 aarch64 aarch64 aarch64 GNU/Linux I am running LVM2 on that system. I updated today, and the dm-raid kernel module seems to have gone missing. I can't get my LVM volume group up anymore, since it can't find dm-raid: root@picard:/lib/modules# lvscan inactive '/dev/vg-data/lv-data' [2.70 TiB] inherit root@picard:/lib/modules# lvchange -ay vg-data/lv-data modprobe: FATAL: Module dm-raid not found in directory /lib/modules/4.18.0-rc8-sunxi64 /sbin/modprobe failed…

Hi, I'm tring to solve an issue on my Orange Pi Zero: at boot time the pins PA18 and PA19 are stucked to Vcc. I tried a lot of solution, now the best result is to add at the beginning of the file boot.cmd the command to clear the gpio configuration: gpio clear PA18 gpio clear PA19 and recompile the boot.scr. Despite this the pins goes HIGH for some seconds until the bootloader reach this line. What is the boot scheme? Why i get this pin HIGH? Is it because the I2C1 is configured? Is it possible to disable it? Thanks Simone

I've had an Orange Pi Zero Plus 2 H5 for a few months, and it is driving me crazy. I can easily boot into the useless Android distro included on the eMMC. I can run most of the distros on the OrangePi website, although they seem to all be missing features or not working 100% in one way or another. I would LOVE to run Armbian on this board. Each time I try, I have huge problems. My video signal is often garbled or at best full of artifacts. I get segfaults every few minutes, and it seems like the filesystem is corrupted. I've tried running it with multiple power supplies (I have several Canakit 2.5amp ones), as well as several different gen…

Hello everyone, I have OrangePiPlus2E and I use Debian Jessie default 3.4.113-sun8i I was download and install Debian Stretch Next on second card and NFS don't work. I installed nfs-kernel-server and nfs-common. Next I copy exports file from older Debian and I can't connect to my Armbian via NFS protocol. Log file tell mi device trying connect, but I get answer from Armbian: can't get hostname. I don't know whad I did wrong. If I change CF card, NFS works fine on Debian Jessie. Could you help me? Regards

Just a quick question due to having just updated and rebooted my Cubietruck.... I was running 5.38 mainline Stretch, but I see that armbian-firmware 5.45 was installed over 5.38... so shouldn't the welcome screen now be saying "Welcome to ARMBIAN 5.45" instead of "Welcome to ARMBIAN 5.38" still? Or is that package not the one that determines the Armbian 'version'? Maybe a better question would be what would update /etc/armbian-release ? The update process was otherwise smooth and doesn't seem to have rise to any nasty surprises . I also look forward to trying out the pineH64 image since I see that has just made a big jump, as well as th…

Hi, I have a BananaPi and BananaPi Pro connected to the Lemaker 7" TouchLCD. When I boot the system, I can't see any console output. I only see a flashing cursor in the left top corner and then it starts the X-window-manager. What do I have to change to see the boot messags on my LVDS LCD? I have tried to change the console=both value to tty0 or tty1 via armbian-config, but this doesn't work. Any ideas? Here is the output from cat /proc/cmdline: root=UUID=e9635572-227e-485c-b76d-b4f0d6d34394 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1920…

Hi, Please see my comments in the other thread: Essentially when booting a Neo Core using the current air/core mainline image, the onboard fast ethernet is not being initialised. At a guess its because this is not included in the device tree (dtb/dts) for the nano pi air image or in uBoot config - however, if the image is to serve both boards it almost needs to - or they need to be separated. Both are probably reasonable options. Right now i'm trying to understand where the board defs for ethernet are collected during the image build using the armbian build environment and try and get a functional image with fast ethernet for the core…

Hello there. I've got an Orange Pi PC+ SBC running desktop Armbian Xenial 5.38 kernel 3.4.113 from its eMMC that showed up pink screen after intermittent Power Up. I was using a 5V power adaptor that became faulty and intermittently became on and off. After replacing the power adaptor and booting up my device to a HDMI monitor, I found out that it now displays nothing but pink screen! Here's what I've done to no avail: 1. Turning on the HDMI monitor before and after I turn on the machine 2. SSHing from UART0 and suing command h3disp -m 5 (or 6 or 33 or 34...). No dice 3. Booting using the same Armbian OS but from SD card. SSH shows me the hostn…

I have installed "Armbian_5.54.180727_Nanopineo_Debian_stretch_next_4.17.11" in the eMMC..My doubt is always boot from eMMC, If blank sd card is inserted in the slot.

Hello armbian forum, I have an Orange PI Win plus with armbian desktop legacy kernel 3.10.y on it. I also have a extension board from my Raspberry 1 which I want to use. The Problem is that the extension board needs the pins 8 & 10 for UART communication. I read already that UART(2) over pin 8 & 10 is used for Bluetooth? I don't need Bluetooth and want to disable it to free up the pins. Uart1 Pin 38 & 40 and Uart3 Pin 11 & 13 are working finde. How can I make this? With overlays or editing the .dts files?

Hi. I have received my new Neo Core and would like to flash my image to eMMC. I tried nand-sata-install but it says there is no target. On the Friendly Arm site they have a utility called eflasher, but I think this does not support Armbian. Is there a way to do it or a guide that I have missed? Thanks. J.

I download the image of this page, unzip the image and use rufus to burn it in a Samsung SD 32 GB evo. I use power supply of 3000 mah https://www.armbian.com/orange-pi-zero-2-h5/ It always fails, and it starts a reboot and kernel panic cycle What image i need use?

Hi all! I have Orange Pi Zero with armbian kernel 4.14. i'm not sure about the topic name, but to me seems like that. I've managed to make spi tft work flawlessly on my zero. But after i've continued with touchscreen module, i've got problems. After X is started, i can confirm touch is working, because when i touch the display, mouse pointer moves. But in the strange way, very laggy (more than a second to respond), but is works only for ~10 secs, then display stops to redraw. And it is not because of bad contacts! Because i've soldered everything together. And it also freezes if i don't touch it. The system is still working tho,…

I've a problem with latest Armbian Debian Server stretch (ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi, Uboot loader 2017.11) on OrangePI One, and OrangePI PC. It boots seemingly OK, but without any output to 1080P HDMI monitor. So I've no video. But Ubuntu Desktop with Legacy kernel boots fine using the same SDCard (and same power supply ). I can SSH to the Debian after boot, here's the boot and diag log. Couldn't wait for senseless SDCard testing to finish, as it works perfect with Armbian Ubuntu Desktop version. Legacy version on 1st boot shown boot progress and defaulted to 720P resolution, which I changed later to 1080P. But Debian Server doesn't sh…

hello everybody, I am new on the linux world but after some search and work , I managed to start my Orange Pi plus 2E with a stretch image armbian 5.38 and everything is working well. Recently after successfully installed several domotic solution like Jeedom and Zwave, I start to work on the integration of a 3G card, but I need to use some CLI to change parameters and it is when I discovered that I completely forgot Root password and the other SU abled user account. Since everything is running from the eMMC, i cannot access to any fils in the OS as explain in some other discussion with card using SD card. Is there a way to recover…

Has anybody a good latency after the RT-PREEMPT patch? I'm using Orange Pi One (H3), Ubuntu Desktop and legacy 3.4.113 kernel patched with 30-real-time143-full-plus-rt-fixes.patch. Also I have the isolcpus=3 enabled. And latency test results for this config is master@orangepione:~/rt-tests$ sudo ./cyclictest -a -t -n -p99 # /dev/cpu_dma_latency set to 0us policy: fifo: loadavg: 2.18 2.49 1.19 1/299 3693 T: 0 ( 3034) P:99 I:1000 C: 364441 Min: 7 Act: 31 Avg: 23 Max: 3655 T: 1 ( 3035) P:99 I:1500 C: 242985 Min: 7 Act: 32 Avg: 23 Max: 3578 T: 2 ( 3036) P:99 I:2000 C: 182252 Min: 7 Act: 43 Avg: 20 Max: 2198 …

How to Disable or Hidethe text that scrolls during boot armbian orange pi?? thanks for your reply!!

Hardware: Orange Pi One with a CF-WU810N (Realtek 8188eus) USB WiFi dongle Software: [MAINLINE] - ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.14-sunxi Goal: Configure and run the Orange Pi One HEADLESS (using a physical ethernet during initial configuration) I've been away from armbian for awhile, so it looks like I've got some catching up to do. I'm running a headless Orange Pi One with a CF-WU810N (Realtek 8188eus) USB dongle. Since it's headless I use a physical ethernet cable to get access and make initial configuration. From the documentation (https://docs.armbian.com/User-Guide_Getting-Started/#how-to-connect-to-wireles…

Hy Just installed the Armbian Bionic image. Tried to attach different usb devices but they did not got registered. So I tried to look at the settings under Hardware in den armbian-config but it's gone.... I remember in the Armbian Stretch build it was Variable... Can someone help me Andy

Was playing around with a well tuned system, wanted to upgrade my kernel - but seem to have broken something. I was on 5.37 - manually upgraded to stretch and everything was working quite well. Today tried upgrading my kernel, and was playing around with `armbian-config` to switch kernels, but didn't go so well. After a reboot had no network. Plugged in the serial console, and was greeted with the following. pi@orangepione:~$ uname -a Linux orangepione 4.11.12-sun8i #2 SMP Wed Nov 22 13:50:32 CET 2017 armv7l GNU/Linux pi@orangepione:~$ dpkg-query -W -f='${Version}\n' linux-stretch-root-orangepione dpkg-query: no packages found matching linux…

Hey there, I have two questions and one of those may be pretty dumb, but anyway. What is the issue that the onboard network is disabled at the moment? The other question is about the tested 3rd party hardware which include various LAN and WLAN adapters. Have those indeed tested with the current experimental images and working? Or is the network support disabled in the current builds at all? Best regards Werner

my opi pc only hosts smb/nfs/transmition, very hot at summer. Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i System load: 0.23 0.23 0.22 Up time: 68 days Memory usage: 28 % of 1000MB IP: 192.168.2.99 CPU temp: 65°C Usage of /: 26% of 7.2G when I change cpufreq gov, find no cpuidle driver, is that true? upstream status about cpuidle driver? I have to disable 2 cores to cool down, and also change cpufreq to ondemand.

Hello everybody and sorry to be sooo stupid. I used to play with Orange Pi Zero H2+ and there was RJ45: it allowed me to connect it via the LAN. Now, with the H5 version, there is no RJ45 connector. And there is no USB port. So how to gain access to this card to start configuration etc... ? Thanks in advance.

OrangePi PC Armbian 5.35 with LXDE desktop Firefox 57.0.1 I haven't done anything with my OPi for 6 months, so when I tried it again, it booted normally except for not looking quite right on my big HDMI screen. I remember fiddling with this in the old immediate-post-boot phase, but http://armbian.com says to use "sudo armbian-config". There were 250 MB of updates, which took forever. Meanwhile I tried to run Firefox, which repeatedly crashed on startup. Installing v61.0.1 didn't help. Also Konqueror, but not Dillo or Midori or Chromium-browser. Back to fixing the display, I tried running it but didn't have the armbian-config, so I downlo…

Hi, I have 3 Orange Pi Zero running with the same sd image. It's all working fine, but yesterday I added a fourth device, which for some reason took a MAC address that is the same of another device, causing issues on the connection for both of them. I'm using the mainline kernel ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi. Searching on the internet, I found someone saying that mac addresses for Orange Pis are randomly generated every time the device reboots, but in my case the taken MAC address is always the same for every device. I saw to that people suggested to check the content of the /etc/modprobe.d/8189fs.conf f…

Hi, After running nand-sata-install at the step "eMMC install: Formating /dev/mmcblk1 to ext4 ... please wait:" mount: wrong fs type, bad option, bad superblock on /dev/mmcblk1p1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so. dmesg: [ 72.516530] EXT4-fs (mmcblk1p1): Unrecognized mount option "flush" or missing value [ 73.928286] EXT4-fs (mmcblk1p1): Unrecognized mount option "flush" or missing value [ 74.238966] EXT4-fs (mmcblk1p1): Unrecognized mount option "flush" or missing value [ 74.822857] +mmc_blk_issue_discard_rq,1809 [ 74.822921] mmc2:mmc…

hello, im use ARMbian on bpi m2 and will programming the gpio with python. i have tested with this little script, but i become a runtimeerror. i can not use the RPI.GPO. What can i used to programming GPO with Python under bpi m2?

Hello all, i wonder what is the status of the support for this touchcontroller. I've got to know that in latest kernels there is prebuilt support for it and in my latest armbian there is a module for this. But following this: https://www.raspberrypi.org/forums/viewtopic.php?t=143581 i failed to make it work. May be i've done it the wrong way in armbianEnv.txt tho. Should i just insert theese line into this file? dtparam=i2c_arm=on dtparam=spi=on dtoverlay=ads7846,penirq=25,speed=10000,penirq_pull=2,xohms=150 According to dmesg log, module is loading, but nothing happens when i touch the screen. If not, should i instead us…

First : i downloaded both Armbian versions for "Orange Pi+ 2" but reported link file names where different from those that actually download : a) link says https://dl.armbian.com/orangepiplus/Ubuntu_xenial_default_desktop.7z, but download file is Armbian_5.38_Orangepiplus_Ubuntu_xenial_default_3.4.113_desktop.7z b) 2nd link says https://dl.armbian.com/orangepiplus/Debian_stretch_next.7z, but download is Armbian_5.38_Orangepiplus_Debian_stretch_next_4.14.14.7z Second : after download i extracted both with : 7z e filename.7z then i run etcher 1.4.4 cli : ./etcher -d /dev/sdd filename.img -y , result sdcard writed, then i inser…

Hello! I have a Orange Pi Win Plus and a vga monitor with an hdmi adapter. By editing the file boot/armbianEnv.txt, I made a change in the basic resolution to fullHD and others, but I still can not get my screen resolution 1280 * 1024 I wrote differently disp_mode=1280x1024 disp_mode=576p and other Аfter another change in this value, at best the board starts with a default resolution, at worst it does not start at all. What to write? Thanks

Hi all, I'm interested in running canbus on Banana Pi (A20). I have problem with setup canbus. Some info about system: ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi in armbian-config -> System -> Hardware only "can" is enable and MCP2551 transreciver is connected to can rx/tx banana pinout. lsmod | grep can: root@bananapi:~# lsmod | grep can can_bcm 24576 0 can_raw 20480 1 can 20480 2 can_raw,can_bcm sun4i_can 16384 0 can_dev 20480 1 sun4i_can Next setup interface: ip link set can0 type can bitrate 125000 restart-ms 10…

Hi Did a fresh install of Armbian_5.38_Orangepiplus_Debian_stretch_next_4.14.14.img on a Orange Pi Plus. Efter reboot, I did a apt-get update and apt-get upgrade, then rebooted... For some reason, wlna0 is no longer listed. I can do a "ifconfig wlan0 up", which brings up the interface - but so far I have had no success in configuring the wlan0 interface, neither by armbian-config nor nmtui I have even tried to edit /etc/network/interfaces and add: allow-hotplug wlan0 auto wlan0 iface wlan0 inet dhcp wpa-ssid "RG47C" wpa-psk "Secret!!!" but I am still not able to get it up and running. After …

Hello, I installed Armbian on Nanopi M1 Plus. I used it for a couple of days but now I encountered a problem: the boot stops after the following writing appears: "started hostname service" I tried to wait several minutes but nothing happens anymore Best regards Marco UPDATE: The problem occurs when the device is powered only by the Debug UART, probably the pc usb is not enough to power it

Hi all, First of all, I must congratulate the Armbian team for such an amazing job! It is really terrific! I'm using Armbian on a NanoPi Neo where I'm running an application that relies on having low latency UART responses. My application is having a latency of around 10ms and I believe that it might be related to the tick rate defined in the Armbian kernel (http://www.makelinux.net/books/lkd2/ch10lev1sec2). I would like to increase the tick rate, however, I got a little lost when I tried to browse the Armbian repository. I couldn't find the actual Linux Kernel source code. In order to increase the tick rate I need to edit the file /include/asm-"ar…

I have a NanoPi Neo Core with eMMC..I have installed armbian os from "https://www.armbian.com/nanopi-neo/" to sd card and tried the "Armbian configuration utility" and "nand-sata-install" to install os to eMMC. But it is showing "there are no targets..please check your drives."..If we give "fdisk -l" command it is not detecting the eMMC. How to solve this issue??

hi. I have build armbian 5.54 bionic 4.17 and it does not boot. 4.14 works but my intention was build bionic. It is possible to switch back to 4.14 when build armbian myself? Thanks for reply in advanse

Hi, I have Cubieboard with armbian. ARMBIAN 5.36 user-built Ubuntu 16.04.3 LTS 3.4.113-sun7i # apt-get upgrade Setting up linux-firmware (1.157.14) ... ln: failed to create hard link '/boot/initrd.img-3.4.113-sun7i.dpkg-bak' => '/boot/initrd.img-3.4.113-sun7i': Operation not permitted update-initramfs: Generating /boot/initrd.img-3.4.113-sun7i gzip: stdout: No space left on device root@cubietruck:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/nand1 32M 24M 8.6M 74% /boot Can you advise me something to solve this issue? Thank you.

I've formatted the opi+2 card I have using recovery and now I get ping screen. I use a 1280x1024 screen with a DVI converter. I tried the HDMI cable using a 1080p TV and it worked without issues. I also tried "h3disp -m 33 -d" "h3dsip -m 1024x768 -d" "h3disp -m 33" and so on. None of them worked. Here is a system output (used armbianmonitor -u) http://ix.io/1iWN !! I noticed this output when used dmesg command: [DISP] disp_ioctl,line:1584:para err in disp_ioctl, cmd = 0x0,screen id = 65536

Hi, I have a Opi+2 board which has an Armbian system installed in its emmc. Now I want to format its Emmc and reinstall Armbian but the problem is I don't have a proper SD card. So I need to do it without an SD card. I have a running system on it, so I can reach the working system. Is there a way of formating it while its running? For example a command does the same thing with "dd if=armbian.img of="/dev/mmcblk1"" (which won't work while there is a system working, its just an example) (mmcblk1 = working system, emmc)

Hi all, I noticed that my OrangePi freezes after 4-5 days of uptime. Something happens (usually around 06:00) when my script simply stop working (no more log entries) and then reboots after ~12 hours (exactly at 13:17 in all occasions). Finally the orange pi becomes unresponsive and heats up to 85-90 degree Celsius. I've checked CPU temperature, disk and memory usage but haven't found anything... I'm a beginner in armbian and completely having no idea what could be the root casue. Could you please help? I've executed a diagnostics you can find it here: http://ix.io/1iQc Related syslog entries: Jul 31 06:10:01…

Hi, I'm trying to set up an Orange Pi Zero with Armbian, so that I can use it as a Network Card (i.e. when I plug it into a computer it's automatically recognized as a Network Card). It seems there isn't enough documentation about this issue. Can anybody help me, please? Thanks in advance. Kind Regards.

Hello, First of all, please understand that I am a beginner level. My project is to make a NextcloudPlus on a Lime2 NAND version because of the following reasons : - Lime2 is Open source board, so no third party code into it - NAND version because I don't want to rely on a micro SD card, as it can be unstable for too many read/write (NextcloudPlus indexes a lot with sync). - SATA version because I would like to store data through a SATA HDD (I feel it is more stable than USB). So, I have tried to make : nand-sata-install ...but after shutting down and removing the micro SD cart, it was impossible to boot from NAND (the…

Hello, does anybody found a working WiringPi version for the Orange PI Zero+ H5?

I know I'm supposed to log with armbianmonitor -u, but I can't behind that ***** corporate proxy. So I made a strace. / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) |__ /___ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | / // _ \ '__/ _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | / /| __/ | | (_) | \___/|_| \__,_|_| |_|\__, |\___| |_| |_| /____\___|_| \___/ |___/ Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi System load: 0.11 0.24 0.25 Up time: 6:55 hours Memory usage: 26 % of 493MB Swap usage: 9 % of 127Mb IP: 10.aa.bb.ccc 169.254.6.65 CPU temp: 45°C Usage …

Hi, guys, today I've menaged how to make my opi1 work with armbian. the problem is that my hdready tv (720p50) has some problem with underscan, the desktop goes off screen so I cannot see the taskbar. Of course this is a problem of my tv, because I have the same problem when I use it as monitor for my PC, but there I can set the underscan through nvidia setting. So, How can I set up the overscan/underscan to see all the desktop on 720p? (using h3disp and set 576p doesn't work, I have "no signal" on tv) thank you in advance

[WIP] Schematics Pros: - board vendor actively participates (listens to the community, provides information including schematic and cares about correctness, tries to bridge developer community and chip vendor) - board vendor take care of their board configuration and submit patches - board vendor provides dev samples - yet another A64 - good powering method Cons: - none specific to this board

Dear Сommunity, I've got an Orange Pi Zero Plus2, it has a WiFi only, no an Ethernet interface. But I want to use a TFTPBoot for my project. That's why I've got two questions: How I can configure/compile U-Boot with WiFi support? And how I can configure it for usage with TFTPboot? Kind regards, Bread Lee

Hello everyone, Is there any utility to deal with overscan when using TVout? I'm using Armbian Legacy kernel. There is a tool called Allwinner_TVOUT_manipulator, anyone have used it?

Hi guys, today a archive to run an orange pi one with a 5v dedicated power ac (not usb one used for smartphones). i try either official. Ubuntu ldxe image and armbian (burned with etcher on Samsung sd) On my first try I saw on my 720p TV (hdmi) some write then nothing else, no signal. And a green led lights up with a red led blinking. on next tries no video signal at all and only the red led is still light on. I can't try android img cause phoenixcard app give me error. Is there something I could try? Thank you or just you can tell me what that leds means

Hi, I built a fresh Armbian Image from scratch (using Armbian build system). After that I used Etcher to burn .img file to SD card. Everything works great, but U-Boot shows, that there is no environment. I used saveenv and fixed a problem. Then I installed Armbian into internal memory (eMMC), same message about environment, I tried fix it same way, using saveenv, but I get only an error message and infinite loop. Screenshot attached. How I can fix that? UPD: My board - Orange Pi Zero Plus 2 Kind regards

I bought a Cubieboard AIO A20 Einstein and wanted to install Armbian. Is there an image I can use to get access to this board? I tried a few images following the install with sd card with no success. I have gone back and forth burning images, reformatting the drive, test and trying again. I'm a newbie but I have completed several installs on other machines just not one like this. I'm outside my comfort zone but keep on trying. I can install to msata and boot from that and there are boot settings in the Cubie desktop. Knowing what image to use (if any for Cubieboard AIO A20 Einstein) moving forward would be helpful. Any other tips, suggestions, how to's, and successes wou…

I just received 3 of the Zero Plus boards and am trying to verify they at least basically work. I'm new to Armbian & Orange Pi but have been using Raspbian & Raspberry Pi's for years. I've downloaded Armbian for the OP Zero (Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14.img), verified the gpg signature and the sha256 checksum and used Etcher v. 1.4.4 on a 2017 iMac, macOS Sierra, to burn SD cards. After burning, macOS claims "The disk you inserted was not readable by this computer." Maybe that's normal for Armbian? diskutil list shows: /dev/disk8 (external, physical): #: TYPE NAME SIZE …

Hello Everyone! Need your help to difficult task. I'm a newbie to micro-computers. Recently installed Armbian on Orange Pi PC Plus (H3), but can't connect to a TVusing HDMI-VGA adapter. Get just black screen, but once got a pink image (as in attachment). That HDMI-VGA adapter works well with notebook and shows picture on this TV. However, this adapter works well with Orange Pi and my Iiyama computer monitor in VGA mode. So, i completely dont understand why Orange Pi not working especially with my Sharp TV. Native resolution of TV is WXGA (1360x768). I tried many resolutions and got black screens, but in XGA (1024x768) resolut…

Hello, I have orange pi zero with armbian and i need to upgrade kernel to version 4.x how to do it? ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 3.4.113-sun8i is it possible at all?

Hello to everyone! I am trying to configure dual boot using u-boot. But I've got some misunderstandings, maybe someone will help me with that problem. When I'm booting from SD card everything works fine: rootdev=/dev/mmcblk0p1 (armbianEnv.txt) or rootdev=UUID=XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX in both cases. When I'm booting form eMMC something goes wrong: I can not set rootdev=/dev/mmcblk1p1 cause in this case I've only error message: But if I'm setting as rootdev=UUID=XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX everything works fine. Maybe it is bad way to use /dev/..., but I need it. So, I tried a lot …

Hello everybody... I will use this small "box" as Access Point (AP) Standard scenario, hostapd + dnsmasq, eth0 and wlan0 bridged to br0 Everything works fine, except one "client" .. Hostapd DEAUTHENTICATE my notebook. It has dual band interface - 03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6200 (rev 35) (Linux Mint inside) .. This was happen on all Armbian images with 4.14.y kernel ... .. On Armbian Xenial with 3.4.x kernel this was no happened.. Wifi connection works fine, for a long time ... Heve anybody same problem .. ?? or not ..? Here is log:

I got Armbian (Jessie desktop) working on Orange PI PC. I did "sudo apt-get update" and then "sudo apt-get upgrade" and everything was ok until it said "Compiling headers (please wait)." It has now been on this step for a very, very long time. Is it stuck or does this take a ridiculously long time to complete? Should I shut it down and start over or keep waiting? The green light is staying on steady.

So trying to run some GPIO interrupts using wiringpi. Using the wiringPiISR function and setting and interrupt handler seems to work, but as soon as the first interrupt happens, the handler gets stuck in some sort of loop and just get infinitely called. Pretty sure this is some bug in sys, since the wiringPiISR function just uses sys gpio calls to do the interrupts. Could be wrong and just be an issue with how wiringPi does it. Either way has anyone come across this and know of a workaround to fix this?

Hi, I have downloaded and installed Armbian to my Pcduino3 board with the legacy kernel 3.4.113. But now I want to downgrade it to the kernel version 3.4.79. Is there any way to do it? Regards,