Allwinner sunxi

Hi, I am trying to use below SSD1963 display modül with orange pi lite. is there anybody who can help me regarding wiring (SPI) and configuration https://www.buydisplay.com/default/7-tft-screen-touch-lcd-display-module-w-ssd1963-controller-board-mcu thanks, Mustafa

I'm using Armbian 5.38 stable Debian stretch 4.14.14-sunxi on A20 Lime2. I try to use PGxx pins (connector GPIO-1 on board), without any luck. I know i must use formula (position of letter in alphabet - 1) * 32 + pin number, so i have tried (for PG11): echo 203 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio203/direction echo 1 > /sys/class/gpio/203/value but nothing happened. I tried from 192 to 203 (PG00 to PG11), but nothing happened. On the same connector (GPIO-1), PC23, PC18 and PB23 work perfectly. What am i doing wrong?

hi guys i have little problem i connect my orange pi zero directly to relay but not work the realy is HUI KE hk19f-dc 5v-sh in yellow box , but if i attach 3v and gnd of gpio work o_O anyone can help me?? thankz

Hi, I was wondering if anyone was having issues with the ethernet port using the legacy kernel ? It does seem to kind of work ... it will get DHCP from the router and configure the routing tables etc but after that it goes wonky. When I do a ping test from the router I get "50/50 transmitted, 15/50 received, 70% loss". A ping test from the opi-win to the router gets a similar result. If I try a ping/ssh from a PC connected to the router I get a 95% packet loss Everything else seems to work fine ... HDMI, USB, WiFi (AP/STA modes) which is really, really nice. Thanks TB

Hello, I've received my OPi Zero a few days ago. I've installed Armbian 3.4.113 (Debian Jessie) on it. Everything seems to be working fine. However, I'm worried by the temperature of the thing. With just the default installation and no extra installed, I get the following: root@orangepizero:/home/sysadmin# armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU 11:53:58: 912MHz 0.00 1% 0% 0% 0% 0% 0% 67°C^C root@orangepizero:/home/sysadmin# armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU 12:00:13: 91…

Recently i have been experimenting with interrupts on orange pi zero plus2-H3 trying to capture data-ready pulses from an external adc on gpio PA19. The aim is to synchronize spi-read-data transactions with the incoming adc data-ready signal. First I tried to get it to work on legacy kernel 3.4 by adding the following section in to /boot/script.fex and compile the .fex file to .bin file using fex2bin: [gpio_para] gpio_used = 1 gpio_num = 6 .... gpio_pin_6 = port:PA19<0><default><default><1> This configured the pin properly as i had tested on other pins with some leds and it works. The driver code for capturing the interrupt was based o…

Hi there! I have been playing around with my NanoPi Neo 2 plus, I managed to get initramfs working thanks to the kernel config of armbian. I have just noticed a problem: only the first of the two USBs works. The second is completely dead. Big disclaimer: I am using an HTC PSU that provides only 1A, not the 2A that should be fed, although I do not know if this could be the cause of the issue. Aside from this problem, I cannot see other issues. Wifi is working and I disabled bluetooth. lsusb without anything plugged in to USB: Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID…

Libre software refers to the free software foundation's guidelines. Can you make an entirely libre software armbian version work on the orange pi one or other orange pi computers? How good will it work? About the orange pi one which devices will not work if only libre armbian software is installed? Notice this https://www.kickstarter.com/projects/bootlin/allwinner-vpu-support-in-the-official-linux-kernel/description If orange pi computers can work using libre software armbian, then how do they boot? Do they use uboot? Thanks.

A speed test on my Laptop shows >300 MBPS download speed. when i run the same test using my orange pi 2e+ on the same ethernet GB switch , I get 50 MbPS download. I disabled wifi. tested the cable.What's going on?

I trying all version on Orange Pi H5 Zero and nothing working. Only one green light start and after 3 second stop lighting. Before i use Armbian on this machine (meybe update firmware)

Hi guys, I´m trying install kodi 18 on my orange pi lite with this tutorial (https://ua3nbw.ru/all/kodi-18-armbian-orangepi/) everything is fine, but MPV player is complete missing on armbian OS. Why? Thank you.

Hello, After I run apt-get update and upgrade, I lose the sound card: aplay -l aplay: device_list:268: no soundcards found... If I check my upgrade history, I can see the following: cat /var/log/apt/history.log Start-Date: 2018-03-16 22:33:12 Commandline: apt-get upgrade Upgrade: libgssapi-krb5-2:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), tzdata:armhf (2017b-0+deb8u1, 2018c-0+deb8u1), ncurses-term:armhf (5.9+20140913-1, 5.9+20140913-1+deb8u2), libkrb5-3:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), libk5crypto3:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), linux-image-next-sunxi:armhf (5.34, 5.…

Hi everyone, i have a strange problem with my a20 lime2 board as described in the topic. Please help The i2s0 pins should be MCLK-PB5 BCLK-PB6 LRCK-PB7 DO0-PB8. But I got data signal from PB7, and the LRCK was missing. a 24 bit 44.1khz file was played by aplay.

Hello guys, do you know what might cause this error, it seems my "smart home" controller is not booting up anymore. In the last 2 weeks it happent again to not display any webpage while accessing it by IP, also the SSH was not working, all leds ware blinking like usually are, like there was normal activity, but it didn't respond to any request, only the ping was working, anything else was not (apache, samba, ssh). I turned it off by long-pressing the power button, it booted up, showing this warning "warning bad CRC - using default enviroment" and it passed by, showing the armbian logo and a blinking cursor, but that's it, nothing more. I think it …

Hi im trying to reproduce my old bananian server on armbian, and I’m stuck on IPSec l2tp psk. tried: strongswan installed by apt and by source compile libreswan by source compile and everytime I try to connect to server on any off the above installs I got a kernel error message about thumb2. does anyone have a IPSec l2tp vpn working with armbian in banana pi with the latest kernel?

I've been using a Cubieboard2 and I have been struggling to get the SPI to work. I've edited the armbianEnv.txt and added the spi0 and spi-spidev to the overlay line. I see the overlays being loaded and I get (only when I've got the spi-spidev overlay on) a /dev/spi0.0 In the dmesg I see a line like "scanning for SPI0 on DT" (paraphrasing as I don't have the screen in front of me ATM.) I don't see any other diagnostic about the SPI though. I haven't jumpered the MOSI to the MISO yet (for a "loopback" test) The kernel is compiled with the sun7i-SPI driver as well as the usermode spi driver. Is this al…

Hello Genius , I am using Orange Pi Zero with (Armbian_5.38) to communicate with my ADC(AD7124-4) while by activating all channels(0 to 7=total 8) SPI able to display only odd channels(1,3,7) not all(evens and odds = total 8=>1,2,3,....7).when same code I run in raspberry pi without any changes it is working fine and displaying all channels(evens and odds=0 to 7=>total 8). I also tried old OS version with Armbian_5.35,Armbian_5.30 but still facing problem. Does anyone know proper solution for it?

Hi, I'm working or orange-pi Zero(H2+) broad with sunxi mainline 4.14.15 kernel. I didn't find any support of Thermal or temperature driver in that. How can I add support of that?? From where I can download the Driver ? How to enable it? Please give suggestions.

Hello everyone, we are Colombian developers and we are making a project with a Orange Pi PC. We tried to connect the Orange with a laptop via USB/OTG but in Serial port mode following this guide, but we exactly need connect the Orange with the laptop via USB/OTG in Mass Storage mode, who can help us to set this mode, we are trying but not with good results. Thanks, I hope that you can help us.

If I open the image file for NanoPi NEO, I don't see the FAT32 boot partition. > fdisk -l Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img Medium Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img: 1,4 GiB, 1488977920 Bytes, 2908160 Sektoren Einheiten: sectors von 1 * 512 = 512 Bytes Sektorengröße (logisch/physisch): 512 Bytes / 512 Bytes I/O Größe (minimal/optimal): 512 Bytes / 512 Bytes Typ der Medienbezeichnung: dos Medienkennung: 0xbcf97591 Gerät Boot Start Ende Sektoren Größe Id Typ Armbian_5.38_Nanopineo_Ubuntu_xenial_next_4.14.14.img1 8192 2908159 2899968 1,4G 83 Linux If I flash…

I received NanoPi NEO and NEO Air boards along with the NanoHat PCM5102a that FriendlyArm is selling: http://www.friendlyarm.com/index.php?route=product/product&product_id=169 It's a good quality audio stereo out addon board compatible with NEO and NEO Air. I got it working with Armbian on NEO Air! I adapted commits from FA's repo to match Armbian's tree and get that DAC working, (original commits here: https://github.com/friendlyarm/h3_lichee/search?utf8=%E2%9C%93&q=pcm5102a+&type=Commits). Add these to 'userpatches/kernel/sun8i-default`: https://gist.github.com/Simon-L/c8c119c86d7d3fe4316387c3ae818379 Add this config to 'userpatches' to have t…

Orange pi is only sending data with tx pin next to the ethernet port. Target is an arduino leonardo clone 5v 16mhz clocked. Maximum baud rate i could run is 115200 8bit data,no parity ,1 stop bit. Shouldnt be i able to run at higher baud rates like 1m? Libraries i am using https://github.com/wjwwood/serial http://www.fourwalledcubicle.com/files/LUFA/Doc/120219/html/group___group___serial___a_v_r8.html

Hello In some cases I should connect to OpenVPN server. So I have .ovpn configuration file. It's works well while I'm connecting from home PC which runs by ubuntu 16.04 and connected though cable. But at work I'm using Orange Pi plus 2e runs by Armbian and connected trough WiFi to my iphone. Connection works well without vpn. But there is a troubles using vpn. It's seems like my orange pi gets connect to server but traffic is flying somewhere another line. Chromium couldn't show pages, tun0 device showing 0 traffic, wlan0 device don't showing new traffic too. What should I fix? Please ask me for some data and where to look for it if you need.

Hi everyone. I have an Orange Pi Zero. 1. I installed legacy kernel to my SD card (downloaded from https://www.armbian.com/orange-pi-zero/ ) 2. I made updates & upgrades. Afterwards, I downloaded WiringOP-Zero from https://github.com/xpertsavenue/WiringOP-Zero 3. Now here comes to problematic part. I checked my files as ls -aol /dev/spi* and could see spidev0.0 and spidev1.0. Then I wrote a test program for my SPI pins (MOSI-MISO-CLK), I can compile the program but whenever I try to use spidev1.0 I get this error below : Unable to open SPI device: No such file or directory …

Hello, I need to use an IRQ interruption with a button. I mean, I push a button, and then a code is executed. Some information: The PIN is PH19, EINT19. and the board A20 SOM. Armbian SO, kernel 4.13 Firstly i configure the digital pin and IRQ from user space: echo 243 > /sys/class/gpio/export echo "in" > /sys/class/gpio/gpio243/direction echo "falling" > /sys/class/gpio/gpio243/edge Now, when I push the button, I can monitoring the IRQ and the counter related to cat /proc/interrupts But now, how can I run a program when the interruption event happens ? I have seen this u…

Hello: I have an issue with one of my opi pc boards: When I connect it to hdmi tv and tv is not connected (switched on before booting the soc), I get just a red screen. Armbian is up and ready. I can log through ssh. Tested in Armbian_5.38_orangepipc_Ubuntu_xenial_default_3.4.113_desktop and openelec (last version). Same problem in both. I'm looking for mods in the .fex file (if there are any that applies to this case). So far I checked http://sunxi.org/Fex_Guide without luck. Time ago, I had a similar problem with an raspberry pi. In this case it was solved with a parameter in the config.txt (hdmi_force_hotplug=1). With thi…

I can't get wifi rt5370 working at banana pi m1 on Ubuntu xenial default desktop. dmesg show: phy1 -> rt2x00lib_request_firmware: Error - Failed to request Firmware. Looks like modules(rt2x00usb,rt2800lib,rt2800usb) are loadede but wifi still don't work.

Hello. I change from diet pi to my own compilation of armbian with rt kernel patch (orangepi zero) In dietpi the my python code run perfectly the lcd screen (GPIO) but in armbian the code fail. When I try to install GPIO with : sudo modprobe sunxi-gpio The output is: modprobe: FATAL: Module gpio-sunxi not found in directory /lib/modules/4.13.9-rt1-sunxi Very thanks How I can repair this? pd: I enabled all gpio overlays in armbian-config Also, I founded this, but I dont understand What is proposed here is for all pins or only for the ones set, and if this can work with I2C, Spi, etc... Thanks a lot in advances.…

HowTo: Setting up resolution 1600x900 & 1366x768 ? &how can i set up other resolutions those are not in h3disp like 1600x900 board is orangepi-pc

I'm working on Orange-pi zero (H2 +)board. Sometimes , after rebooting of system , I Noticed that MAC address is changed. From where It is reading MAC Address?? any help on that?

Hi, first of all thanks a lot for every contributor, this is a great project, I'm an absolute fan! I'm running Armbian on an orange pi 2, everything works fine for a while. I'm running a homegrown python script with flask, this one works too. But after ~1-x hours, I can't connect anymore to my web service. This could be my problem, but in fact, neither SSH works. So I found these things, my script tells me this: ---------------------------------------- Exception happened during processing of request from ('192.168.0.158', 59734) Traceback (most recent call last): File "/usr/lib/python2.7/SocketServer.py", line 290, in …

Hi every body, I have a Orangepi Plus 2E as you know with 16GB eMMC. Have installed armbian via SDCard before and executed nand-sata-install to copy it to eMMC. But currently need to get an image to install on another one. So there must be an opposite action like install_to_sdcard (in raspbian) but I couldn't find it.

Hi all, I recently purchased an orange pi after developing on the raspberry pi (just for convenience). I got it mainly because the integrated memory could be a real asset both because SD are faulty when making lots of memory accesses and emmc can provide a nice layer of code protection when giving the board to somebody else. I set-up everything without issue and I used the nand-sata-install to move everything to emmc...it worked like a charm. I then placed all my proprietary code on emmc and executed without issues. Problem is, I can obviously still insert an SD card and then mount the emmc and access my code since the SD is booted before the emmc.…

Hi, I just saw that my syslog is growing very fast, so i checked it. It's getting spammed with this message every 5 seconds: Mar 11 14:02:46 localhost kernel: [157574.980133] sunxi_i2c_do_xfer()978 - [i2c0] xfer timeout (dev addr:0x48) It's a fresh installation of armbian 5.38 (ubuntu 16.04) on my orange pi pc h3, i just installed snmp and nginx, jdownloader (java) and tightvncserver. Is there any way to stop this? what do i need i2c xfer?

Hi, Is there any sleep or low power modes in orange pi with soft wakeup I want to wake up Orange pi zero at some specific time. For that i go through some forums and searched alot about that but could not found any way to do this. I also go through some 'rtcwake' commands but they didn't work. Any Idea regarding sleep modes and how to wake up would be great help for me. Thanks,

Hello, When I flash the newest version of Armbian debian, and plug it into my Orange Pi Lite, nothing is displayed on my monitor, even if the led is green. My monitor is 4K LG display. With Debian, the HDMI output is not reconized. I tried with Armbian Ubuntu, and the instalation guide is displayed, but the edge and the bottom of the screen are cut. After one reboot, the screen is entirely black and I can't do nothing. Any help is welcome

Hi, just installed Armbian 5.38 mainline (both debian server or Ubuntu server fresh installation). There are two processs eating cpu (kworker), and I read some other users have the same issue, but there is a solution? Other problem: I use this board with Bluetooth dongle to monitor my solar plant. Sometimes Bluetooth dongle disappear from lsusb or hcitool scan tell me device is busy with no reason, just unplug and reconnect usb dongle and all restart to work again (tried with two different Bluetooth dongle, this dongle works with no problem at all in another orange pi pc, no disconnection or disappear). The pow…

Orange pi zero running Pihole. The web interface stopped updating and I found the /var/log file was 100%. Only way I could get it working again was to delete some of the files . How do I stop this filling up again please? From what i read it may be a armbian issue more than a pihole?

Mainline kernel unable to load sndhdmi modules. Thus no sound with it .it looks amazing though.

Hi, I use armbian distribution on opi+2e , in order to operate the Jeedom home automation system. I occasionally encounter crashes of my opi, which becomes inaccessible in SSH. We are several users of this system to encounter the same problems. In logs, date is 1970, so we suspect a time synchronization problem. We use timedatectl for ntp synchronization, but it appears that rtc clock (fake clock) is not stable. Why? Any solution to keep rtc clock synchronous with ntp? Somes members of Jeedom community try with hardware RTC clock on I2C, and it seems working. But any existing other solutions? Thanks.

H there, I am using OPi0 TV out. I know, there are hardcoded PAL and NTSC resolutions only. But I would like to ask, if there is any tutorial how to build it up with my own lower resolution e.g. 320x240? (i know I should recompile driver for it but any help where to start is appreciated) Many thanks.

Hi, sorry for my english. I have an orange pi plus 2 and i try to turn it's wifi module on ap mode. I install hostapd et and set config lines in /etc/network/interfaces. After reboot the OPI can't finish the starting. I mean it's boot and one second after login line appear, the screen display lot of lines and it reboot again. What can be the problem? Any help? PS: The system is Ubuntu server installing on EMMC. My power supplie is 5V - 2,5 A (So i think it's not a power issu).

Hello, I want to use SocketCan on the Banana Pi / Allwinner A20 with the internal CAN interface. I have tested my hardware in the past using can4linux and also have some experience with Socketcan and other interfaces. Configuarion: Armbian root@bananapi:/# uname -r 4.4.1-sunxi loaded the can driver with "modprobe sun4i_can" results in "lsmod": Module Size Used by sun4i_can 5810 0 can_dev 8307 1 sun4i_can And dmesg states: [ 2632.582992] CAN device driver interface But I do not get the can0 device up: root@bananapi:~# ip link set can0 up type can bitrate 500000 Cannot find device "can0" There seems …

Hi, we've been running 5.31 with VDPAU support for a long time now, and I've tried to "apt-get dist-upgrade" to newer version of Armbian. With 5.31 VDPAU works well, with 5.38 all calls to vdp_imp_device_create_x11() fail with "Error when calling vdp_device_create_x11: 25" Demonstratable on "vdpauinfo" Spoiler # Armbian 5.38 # DISPLAY=:0 VDPAU_TRACE=1 vdpauinfo display: :0 screen: 0 VDPAU capture: Enabled vdp_imp_device_create_x11(0x9c7f10, 0, -, -) -> 25 Error creating VDPAU device: 25 # Armbian 5.31 # DISPLAY=:0 VDPAU_TRACE=1 vdpauinfo display: :0 screen: 0 …

Hi to everyone, I'm using "Armbian_5.38_Orangepizeroplus_Debian_stretch_next_4.14.14" on a Orange Pi Zero Plus H5 I'd like to test this new board by working with processor overclocking. But it seems to me that it is leased at 816Mhz maximum. Can someone tell me how to take it to 1200Mhz or more? Thanks Antonio

I have a Adafruit PN532 connected over UART to the orange Pi Zero on UART1(p8/10) i added the uart overlays to armbianEnv.txt and edited the libnfc.conf to include device.connstring = "pn532_uart:/dev/ttyS1" #device.connstring = "pn532_uart:/dev/ttyS1:9600". I commented included a fixed lower baudrate to test if it might have been the problem. To thest the theory i connected a arduino due to the same serial port to print somting to see if there was any communication but nothing went through the python code i used was simple : import serial ser = serial.Serial('/dev/ttyS1') print(ser.name) ser.write(b'hello') ser.close() the Arduino sc…

Hi, I am newbie in Debian. I have an inquiry regarding this matter. I am having USB Wifi Dongle installed @ my OPi Zero H2+. It has built-in NIC (Eth0 & WLAN1) for the Debian Stretch. I am using this PI for the FlightAware purposes. 1. I connect to Eth0 from the beginning to access SSH and update all required updates. 2. I use nmtui for the USB Wireless connected to the Wireless AP. 3. Reboot the PI. 4. Install my PiAware 3.5.3 as per their instruction. 5. All Installed without any issue. I noticed that the MAC address of the USB Wireless Dongle is as follow:- wlx7c8bca1f3ad1: …

I using the following armbian and kernel: # PLEASE DO NOT EDIT THIS FILE BOARD=orangepizero BOARD_NAME="Orange Pi Zero" BOARDFAMILY=sun8i VERSION=5.38 LINUXFAMILY=sunxi BRANCH=next ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage Linux 4.14.14-sunxi #1 SMP Thu Jan 25 12:20:57 CET 2018 armv7l GNU/Linux My box have constant kernel dumps in the log: [59763.352618] [<c010db15>] (unwind_backtrace) from [<c010a0d9>] (show_stack+0x11/0x14) [59763.352627] [<c010a0d9>] (show_stack) from [<c0867e29>] (dump_stack+0x69/0x78) [59763.352637] [<c0867e29…

Hello, I Just installed armbian in my cubieboard and dmesg is showing an annoying message: [ 70.366543] rc rc0: IR event FIFO is full! [ 70.382773] rc rc0: IR event FIFO is full! [ 70.398930] rc rc0: IR event FIFO is full! [ 70.414907] rc rc0: IR event FIFO is full! [ 70.430890] rc rc0: IR event FIFO is full! [ 70.446706] rc rc0: IR event FIFO is full! [ 70.462248] rc rc0: IR event FIFO is full! [ 70.477582] rc rc0: IR event FIFO is full! [ 70.492758] rc rc0: IR event FIFO is full! [ 70.507816] rc rc0: IR event FIFO is full! [ 70.522829] rc rc0: IR event FIFO is full! [ 70.537806] rc rc0: IR event FIFO is full! [ 70.552683] rc rc0: IR event…

Hi! Upgrading to the mainline kernel removes /dev/snd/seq, which is needed for MIDI applications. Synthesizers are my main interest in using these boards, so that is a big loss. Since the module is enabled in the legacy kernel, perhaps this is unintentional and could be added to the mainline kernel? Thank you for all your work. Regards, brkl

Hi: I was using version 5.30 at orange-pi-pc and orange-pi-one. it is very stable. I saw some irq complain about 5.35, but I don't know if these issues affect H3 boards. I use the boards as headless server with openvpn and some DI/DO. is version 5.35 stable enough for the work? or I should stick with 5.30? thanks a lot for advice.

is it normal? armbian@orangepizeroplus2:~$ sudo armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 17:49:19: 1152MHz 0.45 4% 0% 1% 0% 2% 0% 23.2蚓 0/8 17:49:24: 1152MHz 0.42 0% 0% 0% 0% 0% 0% 23.2蚓 0/8 17:49:29: 1152MHz 0.38 0% 0% 0% 0% 0% 0% 23.4蚓 0/8 17:49:34: 1152MHz 0.35 0% 0% 0% 0% 0% 0% 23.5蚓 0/8 17:49:39: 1152MHz 0.32 0% 0% 0% 0% 0% 0% 23.6蚓 0/8 /etc/default/cpufrequtils # WARNING: this file will be replaced on board support package (linux-root-...) upgrade ENABLE=true…

Hello, First of all, I did check/tried anything i could find on similar issues, for similar SBCs Main issue: only 2/4 USB ports are powered, but they don't recognize any device (keyboard, mouse, memory stick), although, if i plug in an USB hub, it lights up. I also tried an Android and and an Ubuntu LXDE, same problem. What bothers me is that mouse and keyboard worked with the original Android that came pre-installed on the board. Config: - Orange Pi plus 2E (the one with 4 USB ports) + heat sink + HDMI to VGA converter Power source: I tried 4 so far, currently using a PSU of 5.15 V and 4 Amps, through the DC input, jack ba…

Hello, I have just updated to the latest Debian Server image of NanoPI NEO 2. When connecting via Serial and using vim.basic/tiny I got the following strange behaviour: As soon as I enter the insert mode a newline is inserted automatically. This does not happen when connecting via SSH. So far I haven't experienced this behaviour with my previous image. Any ideas? Kind regards, Markus NB: textwidth is set to 0 (disabled).

Hi Armbian for Orange Pi Pc. how can I set the SPI mode to 3. When I try #include <linux/spi/spidev.h> //Needed for SPI port #define SPI_INTERFACE "/dev/spidev0.0" uint8_t mode, mode |= SPI_CPHA; mode |= SPI_CPOL; ioctl(file, SPI_IOC_WR_MODE, &mode) returns not allowed. Thanks Brett

Hello, I am trying to have a serial link between an arduino and a banana pi. As a basic test, the Arduino is sending "hello" every seconds. I observe that the reception by the Banana pi is not good. I have tried , several baud rates, /dev/ttyS2 and FTDi adaptor. The best result seems to be with the FTDI adapter , at 115200 bps. But I have still a lot of errors, see below. When I plug the FTDI adapter on my laptop, it works without issues. Do you know what could be the cause of my issues? Thank you Sebastien hell»½ýhgn·ïÏÞh»½ëèu·oÝÕýemmÍÿÿý¿¿ëÏÿÿýïï»ÿ½{í»ÿ¯nïÿý{¿ûoïÿÿÿÝÿïÏíumío^huw·oMÕh…

I've just downloaded the Debian-server mainline image for my Olinuxino A20 Micro (Armbian_5.38 etc) and tried, without success, to change the video output from the default HDMI to the VGA one. Following the documentation (https://docs.armbian.com/Hardware_Allwinner/) I modified the boot.cmd file adding the lines: setenv video-mode sunxi:monitor=vga,hpd=0,edid=0 saveenv and recompiling it but the video continues to be enabled on the HDMI output, also after 2 (and more) restart. I noticed that in the boot splash screen a "Err: VGA" is reported. It's not too clear from the documentation if this setting can be applied also modifying the armbianEnv.txt …

Hi I've downloaded v5.38 firmware for my Cubietruck device and replaced on an older version due to my problem with new updates. Etcher was my tool for writing image on SD card and i have cleared SD card before writing new image. When new image installed and device booted up, but WiFi is not working and WiFi module is neither listed in lsmodule output nor module list file. It seems that WiFi driver is not installed or WiFi hardware is not detected. Is there any way to fix this issue? @Igor

Hi all, can some kind soul tell me if this update will break my cubieboard installation? (I know that cubieboard a10 is no longer supported, nevertheless maybe someone can tell me after 5 seconds of thinking "yes" or "no" :)). XXXXX@cubieboard:/etc/apt/apt.conf.d$ apt-get -s -t stretch install dnsmasq NOTE: This is only a simulation! apt-get needs root privileges for real execution. Keep also in mind that locking is deactivated, so don't depend on the relevance to the real current situation! Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be instal…

I should have known better..... today i did an apt update and saw thet there was an update to 5.38. Installed it and like with nearly every last update the device (OrangePi +) didn't boot. Did you even test updates in the stable repo before ? Don't know whats going wrong, so i will test it, but thats annoying.....

Today I did get my NAS-Case "Neo Station NS-120B" for my NanoPi Neo2 (also useable with a normal NanoPi Neo). Because I already did use the Neo2 with armbian (and had soldered all pins on the mainboard - I ordered only the case without a new Neo2 with soldered pins) I didnt want to write the FriendlyARM Image for NAS to my uSD. After completing to built the Neo2 and the 2.5 HDD inside the case (and using the 12V PowerSupply I had) armbian did start up and I could normally SSH into my Neo2 - BUT I cant see the HDD or the HDD-controller (which should be connected via USB). ( @tkaisernow here the Neo2 do get his power over pins and not via the Mic…

Hello! I have problems with Banana Pi and for today - updated all packages, and I can't connect via SSH nor FTP to my Pi. I have not changed anything, but there is automatic script which dist-upgrades the whole system, it is running once a day. Till 12.34pm CET everything was working fine - from logs, even I think till past 4pm I have connected via SSH to Pi, but then after kernel upgrade (seen note after logon) and reboot I can't access Pi in any way. I've tried to see logs: connect SD card to laptop with Linux to check if there is any problem, but didn't found nothing special. I've also tried to attach HDMI monitor but no signal. Seem…

I had bought 3 Orange Pi Zero h2+ cpu (1x256mb ram and 2x 512mb ram) I'had tried Armbian Debian and Ubuntu based, but nothing changed or solved, i'had also tried DietPi(a debian base as armbian), but the kernel still the same: root@192.168.1.181's password: ___ ____ _ _____ / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) |__ /___ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | / // _ \ '__/ _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | / /| __/ | | (_) | \___/|_| \__,_|_| |_|\__, |\___| |_| |_| /____\___|_| \___/ |___/ Welcome to ARM…

I have installed the 'watchdog' package (apt-get install watchdog' on an Orange Pi Plus 2E, and it does not seem to be working as I would expect. If I write output to /dev/watchdog the system will reboot, but if I stop the watchdog service (and wd_keepalive) the system does not reboot. I did un-comment the path to /dev/watchdog in the settings file, but have generally not changed anything else. Is there some other required setup needed to allow this to function?

Last year I tried the 5.30 and was not happy, as the PI did not give signal to HDMI, when monitor was plugged in while booting. After booting, plug in HDMI cable, picture was on monitor. Now tried the newer Armbian_5.38 on a 2nd Orange PI PC, and I get NO picture / signal on HDMI. Nothing. Have also changed to several resolutions, but no image on monitor or beamer. I have also tried the "DVI adapter option" in the "armbian config". What is wrong with it? I have 2 PI PCs. Same problem on the other PI (now there runs a PI HOLE, as I was not able to get a picture without un-pluging the HDMI cable, so I switched over to a Banana PI M1 for…

Hello, i have a old Banana Pi M2 with the current Armbian in use. I use the green LED with Heartbeat Signal. Today i try to connect with putty but after Username and PW nothing happen. Samba Service work normal. Then i have look at the Banana and the green LED was lightning constant and no heartbeat blinking. Maybe the trouble was because in a few meters distance sawed with a circular saw. Has perhaps caused interference or power fluctuations. No idea and maybe just coincidence. I have been using Armbian for only two days. Previously, the manufacturers ran Distribution for two years. I have Google and found out t…

Good day. I install arbian image Armbian_5.38_Nanopiair_Debian_stretch_next_4.14.15 Add to i2c0 to arbianEnv.txt When I try to run i2cdetect 0 its run very slow, and this error mesage in dmesg output -- [ 1073.376650] i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0 -- [ 1075.456410] i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0 The same in i2c1 and i2c2 bus

Hi guys, I've just got my first of the H5 boards, and am loving it so far. I have a quick question however. On all of my Zero (H2+) boards I have an led on indicating power. On the H5 board this LED is not lit. Do I have a busted LED or is this intentional? Sent from my ONEPLUS A3003 using Tapatalk

Hi All, I did upgrade of my Cubieboard 3 from 5.31 to Armbian 5.36 and everything was fine. But than by short system audit I find an old package "rpimonitor" that was used long time before and never being used now. I did "sudo apt purge rpimonitor" and "sudo apt autoremove" to remove dependencies and it starts... Somehow my CPU load was vanished, on Idle mode it shows at least 2.0+ and at least 4+ on load. Looks like it is twice higher than it is. If I run top command, nothing shown. Only mysql time is 117+ Hours. But, Idle is 98.7... :~$ top top - 19:29:50 up 22:07, 3 users, load average: 2.28, 2.35, 2.93 Tasks: 112 total, 1 running, 111 sleeping, 0 stopp…

Hello ! I am use A20-OLinuXino-MICRO-e4GB Debian server image with mainline kernel work fine with eMMC, but I need eMMC support in Ubuntu desktop with legacy kernel. How I can do it ? Sorry for bad English :-) I hope, you understood me :-). Thank !

Orange Pi Zero Plus (H5 / 1000M ethernet ) Is a working Armbian system ? ..... It's probably new :-)

I am running cubitruck wheezy 7.5 from 2014, Kernel 3.4.104 for over three years as homeserver with VGA display. How can I activate HDMI for a new display. (I cannot reinsall the whole system, growed up for all the years) I already changed the settings in fexfile: [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 3 screen0_output_mode = 6 screen1_output_type = 3 screen1_output_mode = 6 also changed fex to bin and reboot, but no HDMI-output Can anybode give me a hint?

Hello, I'm running a Cubietruck with legacy kernel (3.4.113) since a long time. The use of the legacy kernel is mainly due to the fact that I'm booting from onboard NAND and this was not supported by the mainline kernel for a long time. Meanwhile Armbian's mainline kernel became Stretch in its server flavor and I'm thinking about migrating. However I'm suspicious this will still break NAND boot, despite the fact that the documentation claims plus "missing NAND support" is not listed under "known issues" for the Cubietruck. Can anyone confirm or deny that mainline kernel meanwhile does/does not support booting from NAND on Cubietruck? And if…

good night, is ethernet and usb a shared hub on Orange Pi Plus 2E and H3 SOC? i get max dl\up speeds on speeds tests and good write and read speeds but when i dl something it max at half my Internet speed thanks

1. Orange pi pc cant shut down ,remains blink. 2. Cant eject usb /sda file directory not available. 3.funny with much updates still cant connect to Internet with clearing block interfaces from armbian config.

Hello, I'm following this project : I was recently spending time on the activities to do with children, 3D printing and robotics, and in order to be able to try to follow https://docs.armbian.com/Developer-Guide_Build-Preparation/ i have bought a new laptop which respect the requirements (SSD, ram...). So now my next goal is to try to make a custom version of armbian dedicated to the schools. To start, for the first step, I would like to try make a localized version of armbian in French by default, in order to be more easier for the French speaking user. With the new evolutions of armbian for OrangePiPC+, there is an ubuntu…

SBC is banana pi M1 I tried the banana pi at church today, things went great as for the Libreoffice impress presentations but it was hard to navigate to menus because the banana's resolution was set to 1920X1080p. Everything was too small in the projector, we need something like 1280X1024 or 800X600. I tried `a10disp changehdmimodeforce 4` to change it to 720P, on the projector but display became unstable and I had to reboot to get it back. We have two modes for projector, VGA (HDMI->VGA converter cable) or plain HDMI. Today I tried the VGA but we can also do HDMI. Please help. Thanks.

Hello ! I know that there are already topic talking about that, but they didn't helped me. I have Armbian 5.38 Desktop. I plugged the camera, and I think it's on the right side: I followed instruction of Garlic here: Nevertheless, with motion I get a grey screen telling me that the camera is undetected: I noticed a very small impact on the cable after the delivery of the camera, but because it is very small, I don't think it's the cause. I don't understand, and any help is welcome. Thank you !

Hello, I use the BananaPi M1 as network bridge with tranparent http proxy and filter with 2nd ethernet (USB adapter with AX88179 Gigabit Ethernet). But since latest update with kernel update, the network seemce to be go down often or the sytem is going bad. I can't find any solution and need some help. If you need some more information, please tell me what I should send. Thank you! Edit: The system is stuck on reboot... have to put of the power.

Hi, I tried two builds for my OPI Zero. Armbian_5.35_Orangepizero_Debian_jessie_next_4.13.16.7z Wifi works but no audio. (and instabel ethernet connect) Armbian_5.35_Orangepione_Ubuntu_xenial_default_3.4.113.7z Audio works but no WiFi In witch build works both ?

Hi all, I have a OrangePi Zero 2 Plus - H5 and installed Armbian buut when i build WiringOP it gives hardware line is missin message. I think so /proc/cpuinfo file is creating by armbian when bord is booting and lines contains all cpu informations. How can i fix the issue? There is any idea? Thanks in advance.

Hi, I have just upgraded my BananaPi from Lemaker's Lubuntu 3.4 kernel to the latest Armbian with kernel 4.9 and I can't enable 1-wire to read ds18b20. I suspect the enabling procedure has changed? What I did was: 1. bin2fex /boot/script.bin > script.fex 2. vi script.fex Appended this section exactly as it was on my previous Lemaker kernel 3.4: [w1_para] gpio = 4 3. fex2bin script.fex > /boot/script.bin 4. reboot 5. echo 600000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq 6. modprobe w1_gpio 7. modprobe w1_therm 8. ls /sys/bus/w1/devices/ empty answer In the "known is…

Hello, I have decided to try out Ubuntu 16.04 legacy on my original banana pi for the first time and to my surprise the first problem I noticed is that the usb ports weren't working at all. I tried two keyboards which are working fine on all my Linux computers all running on mint 18.3 (logiItech k360, and insignia nsc5011-c) they are both wireless keyboard + mouse combos they did not work at all on the banana. I previously had bananian on it prior to today and all usb ports were working fine as I was able to connect external usb hard drives to it. I decided to connect the banana to my LAN and ssh to it from my laptop, did an apt update…

Hello. I install the 5.35 Version on a OrangePiPc+, all run in good condition. I upgrade to the 5.38 without problem (kernel 3.x) I upgrade the kernel to 4.x, so long as i didn't reboot, all is in function (with Ubuntu) and my USB Tevii 662 is recognized (and run with TVHeadend). After reboot, no Ethernet and no USB, no possibility to login. I tried all versions with kernel 4.x, even desktop, no function. Anyone has a idea, how it will be run??? Thank's for any idea. P.S. OrangePI PC Plus, 1 GB RAM, 8 GB SSD-OnChip, Tevii S662 S2 USB, TVHeadend.

Hi all, I have an application running on an orange pi pc plus 2 over the emmc 8gb memory. Everything is in there (os, db sw) and what it does is acquiring data from some sensors and then pushing it over mqtt to a server. Now, due to frequent internet connection issues, the board is able to store up to ~ 1 month of data in a local db but this means quite a lot of writes per seconds (plus all the logs). I would like to have an idea of how much the emmc can keep up with this rates and thus I am trying to understand how to calculate the life span in years (hopefully nothing less). Can anyone help me on how to do that? I am using right …

Hello. this is my first post. I was looking through the forum but I did not find a similar problem. About power supply - until now I did not have any problems, I use a computer power supply. After a few months of non-use of my device, I downloaded an updated, latest version (Armbian_5.38_Lime2_Ubuntu_xenial_default_3.4.113_desktop) to an old, previously functioning card. When I connected the device, it did not turn on. I tried to turn it on manually, but nothing happened except the short flash on the connected mouse. A while ago, I uploaded an older desktop version to NAND. I used the sd card to start up. Is it possible that this older version loaded on NAND c…

http://ix.io/NWB Hi, above i posted armbianmonitor -u out. I tried dettaching usb disk due errors in btrfs for continuos recording, disk was mounted in ro mode. Now, with only microsd happen same thing, no btrfs errors obviusly, but orangepi plus 2e go down time to time, light are on, but don't have ssh access or ping. Please someone could show some light in it, thank you. Edit: sorry, I forget say my wlan config is make in plain /etc/network/interfaces, with fixed IP, the SBC work fine up to go down.

Hi , sorry for my english guys after Update /Upgrade to armbian 5.38 , my sytem did not rebooting anymore , before it was Fine for Long Time with Reboot Every Night I have not so mutch Experience with Linux i hope Same one can give me a hand, Best is a Step by step List I‘m connected directly to The Board via hdmi, i did not have a Network cable conected at Moment Because i‘m not at Home and i took The cubitruck with me to My workplace 2 pictures : https://picload.org/view/dagwdolr/fd49eb8f-23bb-4b4d-9763-e9bd87.jpg.html https://picload.org/view/dagwdola/6f5eea…

I'm trying to follow this tutorial here https://www.pyimagesearch.com/2015/07/27/installing-opencv-3-0-for-both-python-2-7-and-python-3-on-your-raspberry-pi-2/ but nothing I do works when I get to install numpy, opencv, or darknet. When I try to build OpenCV following default instructions (or any for that matter) I get: don't know what to do and there's nothing online that helps me out. the only thing that worked was apt-get install python-opencv but it installs a very old version which I can't use for my project. Also when I try to make darknet I get:

Unfortunately I don't have a USB keyboard or USB UART cable around... is it possible to compile an image that has my wifi information baked in?

Hi, I'm running armbian ubuntu image 4.13.14-sunxi64 on Orange Prime, and have a problem. Wifi wont work. I can see a wlan0 as a result of ifconfig, but it neither find a wireless network, nor connect to provided. From dmesg i can see driver is spamming with message [ 303.336420] RTL8723BS: ERROR sd_recv_rxfifo: alloc recvbuf FAIL! I have /var/log overflow in several minutes and also frequent system freezes. rmmod r8723bs causes all this stuff to stop. Can anyone suggest where should i look? Thanks. Btw, self built debian stretch image 4.14 gives the same behaviour. I understand that H5 support is experimental, I just want t…

Please help me build driver for usb wifi adapter Tenda u12 (RTL8812AU chip). Board Orange Pi+2 (Armbian OS https://dl.armbian.com/orangepiplus/Ubuntu_xenial_default_desktop.7z) adapter driver link http://tendacn.com/en/download/detail-2863.html build log with error Spoiler root@orangepiplus:/home/alex/Desktop/RTL8812AU_linux_v5.1.5_19247.20160830# sudo sh ./install.sh ################################################## Realtek Wi-Fi driver Auto installation script Novembor, 21 2011 v1.1.0 ################################################## Decompress the driver source t…

Hi, I have been working on this problem for a few days. I have a orangepi plus2e and orange pi 5'' lcd. When I make all the connections and give power to the orangepi, I can not see anything on the LCD. At first only a white light comes out. Later on, I looked at the 5 inch screen produced by OrangePi with 640x480 resolution and the LCD settings on the H3 boards. I tried to set the resolution with the h3disp command, but I did not see the proper resolution. I did these on a different computer screen, and when I changed the resolution, nothing appeared on this screen.

Hi I want to install some packages, but it not found on sources. When i do update repositories by sudo apt update command, the following messages shown that means the repositories is broken. Err:1 http://httpredir.debian.org/debian stretch InRelease Could not resolve 'httpredir.debian.org' Err:2 http://httpredir.debian.org/debian stretch-updates InRelease Could not resolve 'httpredir.debian.org' Err:3 http://httpredir.debian.org/debian stretch-backports InRelease Could not resolve 'httpredir.debian.org' Err:4 http://security.debian.org stretch/updates InRelease Could not resolve 'security.debian.org' Err:5 http://apt.armbian.com stretch InRelease Could …

I'm trying to get a 4K 5.5" LCD to work (only console mode needed ) . U-boot can get it on at the desired resolution : 2160x3840 ( yes it's a portrait mode ) and display correctly . Seems that U-boot is reporting the correct information to set up simpleFB , but I don't get any display after kernel loading . The display adapter (HDMI>MIPI) have 3 options ( switching between 3 different EDID ) , the 2 others are working correctly ( 1080x1920 , 1440x2560 ) . I 'm wondering if this is related to simpleFB limitation , or memory allocation ... problem is that I'm a complete noob ... I can provide any information needed as long as you tell me what…

I've gotten the board up and running and on Wifi, but this is supposed to be a dim wifi 'lamp'. Just to start out: how do I connect the +- to the board How do I tell the board to power on the leds And for more advanced: Is it possibly to do voltage-limiting dimming as opposed to PWM If no: what's the best way to do PWM? (I'm perfectly fine with creating a c program that simply turns it on and off at a specified hz, but there may be a more elegant tool I'm not aware of) Thanks

I have cubieboard2 nand chinese usb-modbus stik with ch340 chip. when I connet ch340 chip to usb cubieboard is freezed, ttyS0 is blocked. cubieboard is work but is very very slow, ssh is not disconnected but don't answer by my command. when I disconnect ch340 chip cubieboard will bee unfrozen but ttyS0 is blocked until I don't make hard (power) reset. Software reset is not unfroze ttyS0. I cannot found src for ch340 chip diver. Driver from china web is not compiling. uname -a Linux cubieboard2 4.14.18-sunxi #31 SMP Fri Feb 9 11:11:15 CET 2018 armv7l GNU/Linux dmesg [ 1129.203974] usb 4-1: new full-speed USB device number 4 …

Hi, Over the last couple of weeks, I have been trying to get Pi-hole working (and more importantly, stable) on the Orange Pi (along with the relevant Orange Pi zero H2+ ARMbian OS) without success. I realize that I am using "Tested" but as yet not marked "Stable" code, however I'm hoping this can help somebody here perhaps in terms of developing a stable OS for these little boards. I have rebuilt the SD card from scratch several time now. The SD card is of reputable make (Sandisk) and in fact I have tried two different cards, just in case this was a card issue. I'm using a reliable power supply, which I have verified by continuously monitoring it with my …

hi my kernel 3.4.113 from armbian my OrangePi Zero dont have poweron - button by default / i know system can wake up from gpios / IR signal / usb events / wakeonlan and another sourcec bu i try todo standby and wakeup after! withous any success (((( :/sys/power# cat state standby mem bootfast goto sleep echo mem > /sys/power/state or echo standby > /sys/power/state working fine ) but i cant wakeup system (((( i try gpio usb ir wakeonan what i do wrong ???? somebody can clarify my issue ??? my loaded modules lsmod g_ether 38598 0 ir_lirc_codec 3685 0 ir_nec_decoder 1556 0 lirc_dev 78…

Hi.Can you help me fix this problem.Can't use usbwifi wl167g(need like reciever). Network-manager show(wifi enable) but firmware missing. Tried to install RT73_linux_STA_DRV1.0.3.6, have error, when step make, rtmp_main.c error "-march=i686". In new version desktop ubuntu wifi working, but shows slow video(I guess many improvements "use" a lot of resources).