Allwinner sunxi

Is it a way to reduce the amount of reserved memory on sunxi64 devices? Trying to remove all useless for my case features (video/audio/wireless) to free up memory/resources for other tasks. The amount of total (413M) vs real (512M) memory is quite low: # grep -e Mem -e Cma /proc/meminfo MemTotal: 422416 kB MemFree: 49620 kB MemAvailable: 314396 kB CmaTotal: 0 kB CmaFree: 0 kB # dmesg | grep Memory: [ 0.000000] Memory: 407924K/524288K available (14144K kernel code, 1456K rwdata, 8700K rodata, 3072K init, 521K bss, 116364K reserved, 0K cma-reserved) # grep extraargs /boot/armbianEnv.txt extraar…

I have a question, does anyone know a method to start in the Opi Lite system the I2S audio interface and in particular I mean the module: PCM5102 / PCM5102a On my old OrangePi Lite board, sound and audio in the configuration as mentioned above really work great ... but unfortunately the Armbian system that I use is no longer supported. This is the Ubuntu version (xenial) and kernel: 3.4.113-sun8i, I managed to update some programs important to me, e.g. mpd / mpc but not to the latest versions. I also have another version of OrangePI 3 LTS and I know that on this model it is rather impossible to start I2S + PCM5102 so I used a good sound card under USB and it is OK. Ho…

Good morning, I have a NanoPi Neo Core that I want to use to generate a PWM wave. As far as I understand, the pin for this is PA5, which is shared with UART. However, by using the corresponding overlay, the UART would be disabled, and PWM would be enabled. Is that correct? What would be the next steps to verify that this is correct and to generate the PWM wave? Is there a specific command to do this? Thanks for your help, and best regards!

Hi, the Armbian_community_24.5.0-trunk.563_Bananapi_jammy_current_6.6.30_xfce_desktop.img shows black screen after going to the desktop GUI (the LCD panel shows "no signal").. PS: The Armbian_23.11.1_Bananapi_jammy_current_6.1.63_xfce_desktop.img after an update/upgrade shows black screen after going to the desktop GUI (the LCD panel shows "no signal") as well.. The Armbian_22.11.0-trunk_Bananapi_bullseye_edge_5.19.6_xfce_desktop.img Armbian_23.8.2_Bananapi_jammy_current_6.1.51_xfce_desktop.img Armbian_23.11.1_Bananapi_jammy_current_6.1.63_xfce_desktop.img work.

Good evening! Thats my first post, I have for a year a Orangepi 3 LTS that I used for my kid, he looks that never switch off the unit by software and use the switch all the time, so suddenly the unit dont boot anymore, the SD card partition table was corrupt, so I mounted a new OS in another SD but does not boot, the green light is not coming anymore. So I connected a TTL to USB Serial device for debugging and it shows the following information: U-Boot SPL 2021,10-orangepi (Sep 06 2022 - 18:22:23 +0800) PMU: AXP806 DRAM: 2048 MiB Trying to boot from MMC2 NOTICE: NOTICE NOTICE NOTICE: INFOS NOTICE NOTICE: INFO: INFO: INFO? BL31: BL31: BL3…

Im using Orange Pi PC+ with Debian 12 minimal image. I tryed to install/compile ovpn-dco-v2 as of standard deb (openvpn-dco-dkms) as well as of git (https://github.com/OpenVPN/ovpn-dco). In bouth cases compilation prcess itself was finished successfully but resulting driver ovpn-dco-v2.ko didn't work. In the first case, the driver caused a kernel error. In the second case, after "modprobe ovpn-dco-v2" , openvpn stuck somewhere in the middle and lsmod has hung down, blocking the console. Before installing the driver package i did: apt install build-essential kmod debhelper devscripts linux-headers-current-sunxi And as i thought everything went fine. …

One of the Bananapi-m1+ GPIO pins is connected to an LED that I need to illuminate as quickly as possible after power-on. Using an older Fedora Linux release, it turns on in 3 seconds. Using a recent Armbian build, it takes 45 seconds. I've tried many ways using services with early "After=" targets, to access /sys/class/gpio/* interfaces more quickly, and this improved it by 5 seconds, but it's still too long. So I tried adding a device tree overlay to set the default value in the pin controller. I am confident the DT overlay is getting read and parsed properly, based on seeing artifacts in debugging streams, but still, no LED illumination. Anybody got any ideas on …

Hi, anyone have already connected a speaker to gpio of lcpi h3 v8 (like orange pi pc). I have tried but im not sure if i2s is enabled on armbian

In case anyone wondering, AW859A / 20U5622 Wi-Fi modules (uwe5622 driver) do not support WPA3. GCMP-128/GCMP-256 are not listed as supported in iw output, SAE or WPA-PSK-SHA256 wpa_supplicant key methods are not recognized as valid. # iw phy Wiphy phy0 wiphy index: 0 max # scan SSIDs: 12 max scan IEs length: 2304 bytes max # sched scan SSIDs: 9 max # match sets: 9 RTS threshold: 2353 Retry short limit: 10 Retry long limit: 9 Coverage class: 0 (up to 0m) Device supports RSN-IBSS. Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5…

I switched armbian repo to stable via armbian-config 24.11.2. The first thing it did, judging by /var/log/apt/history.log, was purging linux-image*: Start-Date: 2025-01-04 22:47:25 Commandline: apt-get -o APT::Status-Fd=4 -o APT::Keep-Fds::=5 -o APT::Keep-Fds::=6 -y purge linux-image* Requested-By: user (1000) Purge: linux-image-current-sunxi64:arm64 (24.11.1) End-Date: 2025-01-04 22:47:27 Then it proceeded to purge and reinstall dtb and armbian-firmware, but not linux-image: Start-Date: 2025-01-04 22:48:34 Commandline: apt-get -o APT::Status-Fd=4 -o APT::Keep-Fds::=5 -o APT::Keep-Fds::=6 -y purge linux-dtb* Requested-By: user (1000) Purge: linux-dtb-cu…

I am attempting to boot my BPI-M2U. It will start the boot, but it does not get to the login prompt. Instead, it resets and starts the boot process over. I am using a 3A Power Supply rated for Pi's. I've tested with other power supplies. One of the BPI images does boot and run. The SD card is untested but works for the other OS. In case it was the SD card, I flashed the Armbian image to the eMMC and attempted to boot off that. I am using the Armbian_23.05.0-trunk_Bananapim2ultra_bookworm_current_6.1.24 image. While the exact spot it dies might change by a few lines, the following is about where it gets. I can build Armbian images f…

Good afternoon. I don't know how to solve a small problem. There is Orange Pi Lite. It runs its own program. The program uses spi-dev and display. You need to compile drivers for the network card. And then a problem arose. I cannot install linux-headers-current-sunxi on a working distribution (the latest one available on the website Armbian_23.02.2 5.15.93 ). And if you set “Community maintained”, then it is impossible to enable spi-dev and the display (Arbian-Config is missing in the repository) How to solve this problem?

Hi, I see in the /usr/lib/armbian/armbian-firstrun script that it runs the command: update-rc.d ap6212-bluetooth defaults for nanopi neo air (and some other boards) However if I try to run this script sudo /usr/lib/armbian/armbian-firstrun start The result is: update-rc.d: error: unable to read /etc/init.d/ap6212-bluetooth setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel version setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel version setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel versio…

Hello, since the build for OrangePi Plus 2 is only community maintained (and there is a warning during installation that this build is not suitable for production), I though of using some generic image or a image for a similar board with standard support. Is it a good Idea? Which image should I choose? Thanks for help, Skalistan P.S. there is no tag for "OrangePi Plus 2", so I used the tag for "OrangePi Plus 2E" since it is required to add a tag.

Hi all, I try to work with Pine64 7" inch LCD on Pine64 A64 board but not working I just modify /boot/armbianEnv.txt for add pine64_lcd=on and add the module how is described on the installation iso, but nothing happens. In the boot file I have found dispmode directive because when installed I used hdmi port to see first boot. Please Help me!

Normally when you have installed a XFCE-Desktop image for the Pinebook A64 you could set the display brigthness with the following pkexec command to a readable higher level - like I did in the past (possible brightness values are 1-10 - on startup this is only set to 2): pkexec /usr/sbin/xfpm-power-backlight-helper --set-brightness 8 read-out command for the current value: pkexec /usr/sbin/xfpm-power-backlight-helper --get-brightness but on standard CLI-install pkexec and xfpm-power-backlight-helper are missing, so to use this command-line (in /etc/rc.local) you have to install these 2 packages: sudo apt install xfce4-powe…

Hi, I'm trying to get Bluetooth working on a Cubietruck running 6.6 kernels including the latest Armbian release. What I'm finding is that a Cubietruck can discover other Cubietrucks but nothing else. Other devices (e.g. Raspberry Pi, Nvidia, Rockpi, and various phones) can discover each other but not the Cubietrucks. I have three Cubietrucks here and testing with the old 4.99 Bluetooth software or the current 5.55 release shows no difference. But if I run a Cubietruck with the ancient 3.4 kernel it can detect other devices but not the Cubietrucks running the 6.6 kernels. I'm using the same Wi-Fi firmware and BT .hcd file in all cases. So it's like the Cubietru…

Hi, I think I'm right in saying that this board once had standard support? I noticed it is now community support and the download page lists that there might be Wi-Fi issues. I have this link for previous builds: https://armbian.hosthatch.com/archive/orangepizero/archive/ Is there a way of knowing when standard support stopped and community support started etc? Thanks!

Hi everyone, I'm new to Orange Pi Zero 2w and Armbian. I'm trying to use the image on the zero2w. Installing on the SD fits and works so far. Unfortunately, there is no image on the screen via the HDMI port. Could it be due to the image? The old OrangePi image with the 5.x kernel works so far. Do you have an idea? Best regards

How do i enable UART 3 in an orange pi 3-LTS. i checked the /boot/armbianEnv.txt file and it has overlay_prefix=sun50i-h6. i then did a sudo armbian-config > System > Kernel > SYS210 Manage device tree overlays > enabled sun50i-h6-uart3 > reboot. after all that i am still only seeing ttys0 when i do a dmesg | grep tty

Hello First, sorry for my English Second, the problem... I have an Orange PI Zero 3, 4gb I install the OS without any problem, the image I use is the following: "Armbian_23.08.0-trunk_Orangepizero3_bookworm_current_6.1.31-1GB-2GB.img" I configure the network with the program "nmtui", everything is fine. I enter through ssh since the screen is not detected through HDMI, I do an apt update and then apt upgrade... everything seems correct, until I do a reboot... my Orange Pi does not start anymore. I am interested in installing openmediavault, that is why I resort to a debian image. What is the problem? I am not using the correct image? I need your help

diagnostics listing of Orange Pi Zero 2W http://ix.io/4Lwr Not sure if this helps..but the stock build is lacking...plus I am getting 1.0 cpu usage at idle Orange Pi 1.0.0 user-built System too busy for benchmarking: 16:33:21 up 25 min, 3 users, load average: 1.15, 1.03, 0.92 System too busy for benchmarking: 16:33:26 up 25 min, 3 users, load average: 1.14, 1.03, 0.92 System too busy for benchmarking: 16:33:31 up 25 min, 3 users, load average: 1.13, 1.03, 0.93 System too busy for benchmarking: 16:33:36 up 25 min, 3 users, load average: 1.12, 1.03, 0.93 System too busy for benchmarking: 16:33:41 up 25 min, 3 users, load average: 1.11, 1.03, 0…

I have Armbian running on Banana Pi R1 without networking access. Is this board suppported at all or it is just a waste of time?

Hello, On Orangepilite2, USB3 is recognised as USB2. I have connected multiple usb3 devices and results are same. I tried armbian, orangepi Debian, orangepi Ubuntu! results are same same too. For some reason all OS have same issue. In picture mass storage is USB3 device.

Look at the description https://docs.armbian.com/User-Guide_Armbian_overlays/ when I set UART I2C in armbianEnv.txt it should be overlay_prefix=sun50i-h616 overlays=i2c3-ph uart5-ph as described on the given page But when I use armbian-config and go to Manage Overlays my settings are not seen and I have to set them but the names of all overlays are preceded by the prefix. After selecting and saving the settings in armbinEnv.txt it is overlay_prefix=sun50i-h616 overlays=sun50i-h616-i2c3-ph sun50i-h616-uart5-ph as a result the defined overlays are not loaded Is it supposed to be like t…

Hi, I'm using Nanopi DUO2 for few IoT projects. Using the microUSB serial console connection is very convenient and fast method to manage this SBC. Unfortunately with latest version of Armbian (tested with v24.11.0) it not working any more. Version 23.11.1 works fine out from the box, but after sudo apt update && sudo apt full-upgrade the microUSB serial console is not available. Any suggestion how to switch it back will be very appreciated. Slawek

I have recently been trying to get my spi ili9341 working under kernel 6.6, having gotten it working previously. I checked to ensure there were no changes in the overlay required by the newer kernel. I confirmed that the pins were configured correctly and that the ILI9341 DRM module had loaded.. Despite this I was met with a white screen. Think I must have missed something I swapped out my SD card for another using an image based on kernel 5.15.88, where I was able to recieve a display. Looking back over the dmesg log, I noticed a slight difference in behaviour with the older kernel. firstly we can clearly see that the SPI driver is requesting to use gpio 34 as…

I built Armbian Edge from source (bookworm, server, no gui) and have no video via HDMI. Being a new build, networking is not set up and so I cannot SSH in to troubleshoot. I reverted to a stable Armbian build on another SD, upgraded that kernel to Edge, and lost video output. This one already has networking set up, I can SSH in, but I don't know what to look for in order to get my monitor working. Goal being, figure out what needs changed, and change it in the build process for a new image. I appreciate any pointers.

Hi, I got my OPiZ3 2GB model last week, but it seems to detect as 4GB sometimes. At first, I thought I got lucky and the seller shipped the 4GB model, but I realized it crashes under load when it do. and I have to restart multiple times to get it right. The issue shows up in htop and free, where it reports double the memory and swap. I’m using the Minimal/IOT image with Armbian Linux v6.6. Here's the output from armbianmonitor -u: https://paste.next.armbian.com/iguzunaved The MemTotal value switches between 4GB and 2GB. Any ideas on how to fix this? Thanks!

I know I need to find out which drivers to use... I just don't know where to start, I know I've seen some people having success with these displays - ili9488, and a couple others - I just don't know if this fits one of those overlays or not. (nothing I've tried so far has worked). Any help identifying and pointing in the right direction, I would greatly appreciate. Trying to get this to work on my Orange Pi Zero 3 4gb. (uploading images has failed.... so I guess I'll link them?) https://imgur.com/a/NORYCj7 *edit 12/21 - renamed topic since I've Identified the display, going to track my (our?) progress with trying to get it to work…

I am running a headless Bananapipro server that acts as an AP. Recently I found that its WiFi net was gone. In the log I found a crash of brcm: Dec 19 02:40:14 localhost kernel: [3919907.052132] ieee80211 phy0: brcmf_fw_crashed: Firmware has halted or crashed Dec 19 02:40:15 localhost kernel: [3919908.004319] ieee80211 phy0: brcmf_fil_cmd_data: bus is down. we have nothing to do. Dec 19 02:40:15 localhost kernel: [3919908.004360] ieee80211 phy0: brcmf_fil_cmd_data: bus is down. we have nothing to do. Dec 19 02:40:15 localhost kernel: [3919908.004372] ieee80211 phy0: brcmf_cfg80211_stop_ap: SET SSID error (-5) Dec 19 02:40:15 localhost kernel: [3919908…

I just booted the NanoPi Neo2 with the latest "Server images with Armbian Linux v6.6" running Ubuntu 24.04 (Noble). After logging in via SSH, I saw a message stating that this image is for development use only and not for production. Based on your experience, how stable is the development image? Am I correct in understanding that there is no stable image for NanoPi Neo 2 ?

Flash 25.2.0 (The Latest Built Dec 01) to a SD card and boot a Orange Pi 3 LTS, Ethernet lost after sudo reboot the board. It did not even come back after physically power off and on. Have anyone experienced the same problem? The same board worked very well with Debian Bullseyes (downloaded from http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/service-and-support/Orange-pi-3-LTS.html). I googled and found Orange Pi 3B has similar problem. https://www.reddit.com/r/OrangePI/comments/1aojmn3/orange_pi_3b_ethernet_doesnt_work/

Good day! I'm using latest armbian build for orange pi lite (Armbian_community 25.2.0-trunk.86 Bookworm). Tried to connect anything to OTG USB port (mouse, flash drive), but it didn't work. DMesg was silent. Had 4 USB devices: [ 1.683435] usb usb1: Product: EHCI Host Controller [ 1.699369] usb usb2: Product: EHCI Host Controller [ 1.727339] usb usb4: Product: Generic Platform OHCI controller [ 1.729832] usb usb3: Product: Generic Platform OHCI controller Then I followed this guide https://github.com/carl1961/Orange-PI-Lite-Usb-OTG-to-Host And I had 5th one after this: […

Hi. I'm running Armbian Distro Debian 12 Minimal/IOT with Gnome GUI on an Orange Pi Zero3 2gb and 4gb models. I installed XRDP Xorg to be able to access from Windows 10. I can access the systems remotely, but both machines turn off after a short period of activity, somewhere between 5-10 minutes, whether they're idle or performing some activity. I've already looked for some hibernation/suspend option, but I only found something related to turning off the screen, which didn't solve the problem after being disabled. The Orange Pi Zero3 2gb machine ran for a few months using another version of Armbian recommended by the manufacturer's website without this…

Current community builds(Debian 12 and Ubuntu 24.04 as well) doesn't support audio codec. Even after enabling codecs with armbian-config ls /dev/snd command displays: seq timer when expectation is to have by-path controlC0 pcmC0D0c pcmC0D0p seq timer Have anybody face with the same issue? any advises how to solve it?

Who can share their valid /etc/apt/sources.list for an armhf SBC? Some past update has messed mine up a bit. Mine is: # deb http://gb.archive.ubuntu.com/ubuntu/ jammy main universe restricted multiverse deb [arch=armhf] http://ports.ubuntu.com/ubuntu-ports/ jammy main universe restricted multiverse # See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to # newer versions of the distribution. # deb http://archive.ubuntu.com/ubuntu/ jammy main restricted # deb-src http://archive.ubuntu.com/ubuntu/ jammy main restricted ## Major bug fix updates produced after the final release of the ## distribution. deb [arch=armhf] http:…

Hello, sorry for the dumb questions incoming, thanks for your time. Lately I spent a lot of time searching for a working image to run Kodi with wifi/ethernet/bluetooh on this board. Does anybody managed to play videos on Kodi on this SBC ? If yes, what armbian image should I choose for this purpose ? Do I have to build the image myself ? Tested LibreElec for this but no wifi because the drivers are out-of-the-tree, not in mainline Kernel. Read about my problem in many posts but didn't find what I was searching for... Not even sure if this SBC can be used as a linux media player. Any tip/link/guide/wiki on how to successfully install kodi/har…

Hi, I have Armbian_community_24.8.0-trunk.6_Orangepizero2w_bookworm_current_6.6.31_minimal on my Orange Pi Zero 2W. It has an expansion board but the ethernet port does not work on it. ip a show eth0 >> Device "eth0" does not exist. Only the Wi-Fi works.

Hello everyone, asking your help as i'm getting a little bit crazy with my pi02w. I'm not able to understand why my board is not able to connect to wifi without the external antenna. I'll explain better, it seems that is able to find it, connect to but not able to work. I cant post the armbianmonitor log as no internet connection. Thanks armbianmonitor.txt

I’ve been running Armbian from an SSD for a while using this guide: https://jamesachambers.com/orange-pi-zero-2-usb-ssd-boot-guide/ Recently, after running apt update && apt full-upgrade, the following issues have occurred: 1. Wi-Fi adapter is no longer detected. 2. CPU utilization exceeds 80% when accessing the Gnome launcher or starting GUI apps (e.g., a web browser, even without opening a webpage). 3. The system becomes laggy and nearly unusable, noticeable when moving the mouse. Are there recent changes to Armbian that affect SSD booting? Is there a workaround for these issues?

I've had an Orange Pi 3 LTS for a couple of months now. I bought it for use as a home theater tv box. I thought I'd use the official orange pi ubuntu release, but it turned out to be really outdated and broken. So I have been trying to get Armbian to work. After a lot of troubleshooting and time spent reading docs and forums, I can't get the thing to play video properly. It plays but is terrible quality and stutters constantly. I've determined that panfrost is working. In orangepi-config, under Hardware, it says the GPU is enabled. But when I run glmark2 I get a score of 100 or less no matter what I do. I've tried old builds of armbian for the pi 3 lts and the…

Hello guys, i'm trying to connect that ili9341 display with my m2 zero but it wont work. My armbian Version: Armbian_23-02-0-trunk_Bananapim2zero_lunar_edge_6.1.11_xfce_desktop The display has a pinout that matches with the raspberry pi, so also the banana pi m2 zero would do the job, since it has the same pinout like the raspberry pi has. It uses 26 pins to connect to the banana pi m2 zero gpio output pins. 3 buttons and a touch panel are available but i only want to use the lcd for now. I edited the armbianEnv.txt to open the spi port and added my overlay tft.dts to /boot/overlay-user but i cant get a picture on the screen, Its just glowing …

Hello, I have't used my old Cubietruck for years but would like to use it again in a project. I downloaded the new Armbian version: Armbian_community_25.2.0-trunk.124_Cubietruck_noble_current_6.6.62_xfce_desktop.img and installed it. There is console display just fine through HDMI, but not graphical display. There seems to be some trouble before as in this discussion: I downloaded this image: https://github.com/IGNNE/cubietruck-armbian-unofficial/releases/ and it seems to work. But when it updates itself, the graphics is gone again. So - is there some old dr…

I will use a orangepi PC2 as openhab server. Arbian 25.2 kernel 6.6.62 minimal.img is installed. The orangepi is connected with an ethernet cable to the router, but is not visible in the list of connected devices. So I suppose he does not make connection. I want to access the orangepi by putty on my PC but as long he is not online, connection is not possible. Led's on the ethernet connector ar flashing. What do I wrong ?

Has anyone had any success with running a current/semi current OS and the NAS/RTC Enclosure/Hat from FriendlyElec. I was never impressed with the NAS/OpenMediaVault image that shipped with the board/hat. I have attempted to strip OMV out of the device and move the device forward with some success. The the Kernel is stuck at v4.14.52. But I would prefer to load a clean current OS and potentially use the correct overlays to enable the extra USB Ports, USB to SATA Bridge and RTC features. Question is does anyone have any information/guide to use a current version of Armbian/Community and the correct overlay file(s) to allow the the JMicron USB to SATA interface and …

I want to understand the feasibility of installing Armbain on a board that is currently Tina Linux. The board has an Allwinner R528 processor and an emmc . The R528 is not a well known Allwinner processor but it is essentially a D1 with two Arm-a7 processors instead of a RISCV processor. It also is a essentially the same processor as a T113-s3 but in a different physical package. I see the mangopi-mq and the nehza have the D1, but I'm not sure it helps. I have a full dts file (3000+ lines) for this board. But what I am failing to get a grasp of is: Given that I that I have a complete dts file, what is the work flow to get Armbian…

Hello all) Please, need help. Minimal/IOT images with Armbian Linux v6.6 Debian 12 (Bookworm) 1. I try configure cubietruck with armbian 6.6, but in system not see nand0 and broken rtc0. When start nand-sata-install i see only "install on sata" and not find /dev/nand . 2. If i try: rtcwake --mode mem --second 180 in console view error cannot open /sys/class/rtc/rtc0/device/power/wakeup: No such file or directory /dev/rtc0 not enabled for wakeup events How i can fix it?

I'm missing something essential. I have NanoPi Neo v1.4 with Armbian 23.5 Jammy CLI (Linux nanopineo 6.1.30-sunxi). My display is Nokia5110 LCD or PCD8544 With spi-spidev DT I can successfully via `spidev0.0` with `spi-tools`. I.e. I confirm that spi is working. Now, I studied about DTO and fbtft driver, found that it supports pcd8544. I wrote this kind of DTO and added it to `armbianEnv.txt` /* * Device: LCD5110 (nokia5110) 1.6"(84x48px) SPI display Module PCD8544 * Module Connector * SDI(MOSI) <- PC0 * SCK <- PC2 * CS <- PC3 * RESET <- PA1 * DC/RS <- PA3 * LED <- PA2 */ /dts-v1/; /plugin/; / { compatible = "all…

I suddenly have a need to test Linux 6.11 or greater, because there's a needed improvement in the panel-mipi-dbi-spi driver (thread keyword ili9488) User "The Going" has kindly advised me to try his Armbian branch with Linux 6.12, so I am here sharing results as I test it with my Orange Pi Zero 3. Initial instructions: https://forum.armbian.com/topic/35635-armbian-242-is-broken-on-orange-pi-pc2/#findComment-207980 At first try, I decided to NOT follow this step: armbian/build> egrep '^-' patch/kernel/archive/sunxi-6.12/series.conf (finds all the excluded patches) Well, I continued. Choosing Linux Edge, shallow o…

Recently I tried to connect CAN bus adapter to my Orange Pi 3 LTS board and it happened that there is not so much information about it, it is outdated or related to other boards. So, after I spent a few days in trials and errors below is my recipe. 1. Connect a CAN interface board. Orange Pi pins are not 5V tolerant, so I decided to use a dedicated 2-channel board from Waveshare: https://www.waveshare.com/2-ch-can-hat.htm (only one channel for the start). You can modify a cheap board from AliExpress though; there are instructions in the Internet. I used the PL10 pin of Orange Pi 3 LTS board as INT pin. Actually first I tried to use the PD21 pin but it seems that…

Hi, does anyone know where I can find a build for linux 5.1 for my orange pi zero 2w. I would like to use fbtft device, so either finding a pre 5.4 linux build, or building one myself (In that case how so because I failed miserably) or an alternative to fbtft. Thank you very much

I'm looking to build an ntp server using the OrangePi Zero 3 and I noticed there is no pps-gpio device tree overlay for the h616 chipset only the h5 chipset. Has anyone created a custom dt overlay? Thanks in advance.

Hi Forum Members, I need have to activate a 1-wire thermal sensor DS1820 on al old BPI M1. I've had these type of sensors allready runing on a BPI M2Zero under Buster (Armbian Kernel: 5.10.60-sunxi) wih these settings in /boot/armbianEnv.txt: overlays=w1-gpio param_w1_pin=PA6 dmesg | grep -E 'w1|wire' [ 6.806929] Driver for 1-wire Dallas network protocol. [ 6.847601] gpio-6 (onewire@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 6.875871] w1_master_driver w1_bus_master1: Attaching one wire slave 28.0121121d29c5 crc 9a [ 7.020059] w1_master_driver w1_bus_master1: Attaching one wire slave 28.01211…

I had to freeze my device on Kernel 6.1.92 & Bullseye to remain operational. Now trying to update/upgrade to Kernel 6.6.nn I run into following probs: 1) Using Armbian-config defreeze and subsequently switch to kernel 6.6.nn works OK 4me, but subsequent apt-get update/upgrade throws me back to kernel 6.1.104. Armbian-config has changed significantly w/ No other Kernel available. 2) Using Armbian-config defreeze, only and going directly to apt-get update/upgrade throws me back to kernel 6.1.104 as well and from Bullseye back to Buster! Its a mess! Will this eventually be corrected and when? RGDS

Hello Team, We are using H618 Allwinner SoC in which we have requirement to enable secure boot as per requirement. We have already checked couple of documents regarding secure boot enable but tools and scripts are not available to create Keys and other process using which secure boot can be enabled This project is based on the armbian image building system and is suitable for the Debian and Ubuntu image building projects of the Wildfire LubanCat (Luban Cat) Allwinner series boards. We are using allwinner-h618-gentoolinux build for build and development perspective. Let me know if need anything else from my end. …

Dear All, I get frequent and random disconnection from orangepizero3 onboard wifi with armibian community (self-built) both trunk and 24.02 current kernel, 6.6.26 and 6.6.28 message is always [21738.338021] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share it [21848.116072] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share it [21915.426734] unisoc_wifi unisoc_wifi sta0: sprdwl_report_connection sm_state (5), status: (2)! [21915.426817] unisoc_wifi unisoc_wifi sta0: sprdwl_report_connection Vodafone-CSC failed status code:1! [21919.477424] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share …

Dear community, Im searching the device-tree overlay files for Banana Pi M2 Berry/ Ultra in dts format. I found: sunxi-DT-overlays But that doesnt contain the sun8i-r40 overlays I want to see how the i2c0, i2c1 and w1-gpio overlay looks!" greetz, hexzhen3x7

Hello! I could find quite a bit of information about the analog video output for OrangePi Zero 2W on Armbian under Ubuntu. On Android TV-OUT works. Are there any plans to add this feature to Armbian? It is very critical for me. If no one plans to do this now, then I would be extremely grateful for advice from experts on how to port / modify existing drivers, perhaps take something from the AndroidTV 12 code, where the video output works? I am a developer, but I have not previously dealt with driver development for Linux, but if I understand in which direction to act, then using ChatGPT sooner or later I should be able to cope. I would be very grateful for any he…

Hi, I have a question about distro upgrde. This is the information on welcome screen: Packages: Ubuntu stable (jammy), possible distro upgrade (noble) Support: DIY (community maintained) I checked the release info on https://www.armbian.com/orange-pi-plus-2e/ and the noble is available. I used sudo apt dist-upgrade and it found no upgrade. Is there any wrong with that? And how I can do the dist-upgrade except writing a new image?

Hi All, I''m using a BPI M2 Zero, where a 100 MBit ethernet Interface is implemented on the board. Since I'm using DHCP for this interface, I found that the MAC Address of this eth0 interface changes on every boot. The MAC Address of the wlan0 interface is permanent and don't changes during boots. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Di 30. Jun xx:xx:xx CEST 2020 Debian GNU/Linux 10 (buster) 5.4.45-sunxi ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 17:42:11 up 25 min, 2 users, load average: 0,00, 0,00, 0,05 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 ether 8a:aa:ea:69:67:50 …

Does anyone use an infrared remote control with the Lirc / rc6 / mce program..and have a verified configuration? I can't configure the above to work on Orange pi 3 lts But I want the Lirc program and not the ir-keytable 🙂

I have a question for more experienced users. Quite a long time ago I built an internet radio based on OrangePi Lite + DAC I think in the I2S interface with the module: PCM5102 ... PCM5102 DAC Decoder I2S -Aliexpress unfortunately the board broke down. I have another model, the aforementioned Pi 3 lts but it seems to be less supported. Can I connect the above-mentioned PCM5102 module to this model? Or maybe buy some other supported model that will work just as well as Pi lite with this DAC model or another? Ps. it would be nice if it had the ability to upload Armbian firmware to emmc flash memory I installed Armbian/Ubuntu on Pi3lts but I get some erro…

I am listed as the community maintainer for the Banana Pi M2 Zero. I haven't actually done any maintaining but I am thinking about doing so now. But before I do, a couple of quick questions. 1) The latest build (as far as I can see), is Aug-31st, 2023. Do I have that right? Or am I missing something? 2) The main page for the Banana Pi M2 Zero (https://www.armbian.com/bananapi-m2-zero/) shows a link to Armbian_community_24.11.0-trunk.273_Bananapim2zero_bookworm_current_6.6.54_minimal.img.xz which is for "Minimal/IOT images with Armbian Linux v6.6". Is that a generic build for all community maintained sunxi hardware? Or is that a specific Banana Pi M2 Zero …

I had an OrangePi Zero LTS and set up an access point using the following commands: % sudo apt install dnsmasq-base -y % sudo sed -i "s/#MulticastDNS=no/MulticastDNS=yes/g" /etc/systemd/resolved.conf % sudo nmcli connection add type wifi ifname wlan0 con-name access_point autoconnect yes ssid <ssid> % sudo nmcli connection modify access_point 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared % sudo nmcli connection modify access_point connection.mdns 2 % sudo nmcli connection modify access_point wifi-sec.key-mgmt wpa-psk % sudo nmcli connection modify access_point wifi-sec.psk "<password>" % sudo nmcli connection up access_point % sudo host…

Hello! I'm tryiing to make iBeacon scan service. But can't make Bluetooth work on OPi0+2H5. I'm using "Armbian_20.02.1_Orangepizeroplus2-h5_bionic_current_5.4.20_minimal.img" as OS, but no hci devices in system after start. I reded many topics from this forum and nothig helps me. Can't start BT Is BlueTooth part work on this board? Can I use it? I need only "lescan" functional....

hi can somebody fix repostiory install list error for chromium as chrome-commen and chromedriver wont install problem: chromium/noble 9:126.0.6478.182-1~deb12u1+narmbian1 arm64 web browser installs with version therefore chromium-common and chromium-driver,will not install because its looking for dependency chromium 126.0.6478.182-1~deb12u1+n1 Without the ":9" i presume he following packages have unmet dependencies: chromium-driver : Depends: chromium (= 126.0.6478.182-1~deb12u1+n) E: Unable to correct problems, you have held broken packages. please can somebody fix

I compiled an environment for an Orange Pi zero using CSC, Edge , Jammy, console server, standard. I didn't change any of the defaults. Things works except for the OrangePi expansion card with dual USB ports. The expansion card USB ports are not recognized. Anyone know what I need to select to get the expansion board working?

Since there isn't an Orange Pi Three forum I am going to post it here. Due to python requirements for PiKVM I installed the latest Jammy build. When i did the install everything looked like it worked but I could not get the remote keyboard and mouse to work with the OTG port. I tried changing the dtb but it didn't work. Comments in the kvmd-armbian discord channel recommended trying a different kernel. After trial and error I found OTG worked with kernel 6.10.9-edge-sunxi64 and remote keyboard and mouse functioned. With the default 6.6 kernel the ethernet port didn't work, but wireless worked. I was also able to get my mt7921u USB wireless adapter to work. In 6.10.9 the …

Hello, I'm a lay user, I don't know much about Armbian and networks - On my network I have a router whose default DNS is set to point to an OrangePI 3 lts with Armbian 23.02, where I installed AdGuard (v0.107.52) and created my rules to filter advertisements through URLs that I access through the web browser of any device. It works almost 100% as I would like - I use a NO-IP DDNS on the router to access the surveillance DVR and I can see the cameras fine on my smartphone. However, when there is a power outage and then it comes back on, there is often some kind of synchronization failure between the router and the OrangePI to access…

I want to use GPIO Pi16 on the 13 pin expansion header of the board. This pin is claimed by the kernel for the ethernet MAC. According to the SOC Datasheet this pin has the option to provide a 25 MHz clock signal for the ethernet MAC, which is not relevant for this board. Thanks to this Topic https://forum.armbian.com/topic/30274-armbian-build-how-to-modify-dts-file-to-change-gpio-mapping/ and the device tree source files https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts, https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi an…

Which is the correct overlay to specify for libcamera support for the Arducam IMX219? I am assuming this would go into /boot/armbianEnv.txt ? The packages libcamera0.3 libcamera-tools libcamera-v4l2 installed properly, however, all examples on the net apply to PIs and not the OrangePiZero... Thanks in advance.

Hello! I've downloaded the current images for BananaPi M1 offered in the site, as "Community Maintained" builds, but none of them is capable of producing video output from HDMI nor composite video. Both the Ubuntu jammy and Debian12 versions lose the video output as soon as the kernel starts to load, after the u-boot screen. I tried the desktop and server images, without any luck. With the older 5.x kernel, the ubuntu-jammy image that I've downloaded before loads fine. I know it's an old board, but it still gives me some amusement time tinkering with it and playing retro games. Anyone experiencing the same problem? Thanks!

Hello everybody, I'm new in armbian and Cubietruck. It looks to me that bluetooth is installed but if I scan for devices no devices will be found. I have the impression that something is wrong with the driver installation. I used the file image "Armbian_community_24.11.0-trunk.130_Cubietruck_noble_current_6.6.44_xfce_desktop.img.xz" for installation. Any help would be appreciated. Best regards Albrecht

Hi, I have problems with NanoPi NEO on Allwinner H3 due to sudden sporadic Linux kernel overheating shut down. I'm using the Linux kernel 4.14 on Debian Trixie. The syslog shows: The hours before, the kernel shows above 80°C by: But there is not much load on it. When looking to "top" I see less then 10% as load average and more then 90% idle. "iotop" shows all processes <1%. And when measuring the chips, all are cool at below 40°C It looks like the CPU suddenly get into a hot-state above 80°C, because it stays there for hours independent from the process load. Even after a reboot command, the system comes up again and is still above un…

Good morning, I am having some problems with the i2c-1 bus, as it sometimes gets stuck even though I have external pull-up resistors. I need to be able to reset the bus to fix it and check the status of the channels, but I don’t know which Linux GPIO corresponds to the physical pins that the kernel associates with PA18 and PA19. I have tried using wiringPi, but it doesn’t indicate this. Can anyone help me? Thanks!

I've tinkering with this board, and trying to boot from spl, but the boot halts after reading the temperature sensors, which does not happen when booting from the sd card. After booting from the sd card I read the sensor that causes the problem # cat /sys/devices/virtual/thermal/thermal_zone0/temp 51740 I found in a forum some kernel patches to mitigate this: https://forum.manjaro.org/t/support-for-orangepi-zero2-h616-ddr3-zero3-and-zero-2w-h618-lpddr4/154679 Why does it fail when booting from spl, and not when booting from the sd? Here is the system info: # cat /etc/armbian-release # PLEASE …

Hi, I have managed to install u-boot on the spl flash, and it properly runs and detects everything, but i've run into a bit of an issue, while loading the kernel, it gets stuck. To create the usb drive I just cloned the partition of the sd card (not the whole card, just the ext4 partition), I don't know if that can be the issue. here is the full log: https://pastebin.com/jPEkMnYq Any ideas?

I want to completely disable display subsystem on Orange Pi Zero LTS (Debian 12 (Bookworm) minimal/IoT build 1 oct 2024). I blacklisted the GPU modules (lima, gpu_sched, drm_shmem_helper), but i can't find a way to disable sun4i-drm. Is there a way to disable it completely w/o recompiling the kernel?

I'm testing different firmware versions for OrangePi 3 LTS a bit and I have to mention that version: Armbian_community_24.11.0-trunk.202_Orangepi3-lts_noble_current_6.6.44_gnome-kisak_desktop.img It has a flaw that can cause some trouble for beginners, i.e. after installing, the system automatically goes to the suspend option after 15 minutes 🙂 Disabling the suspend option completely helps, but it then prevents you from using the suspend option by clicking the button on the board 🙂 This is probably an error related to both battery and mains power supply. https://discussion.fedoraproject.org/t/gnome-suspends-after-15-minutes-of-user-inactivity-even-on-…

When I attempt to run the Sudo apt update command I am receiving an error message about the Repository not being signed. See attached photograph

With Armbian 22 (kernel 5.15 and bullseye/jammy) the Orange PI 3 LTS worked great including WiFi, ETH, Bluetooth. Partly thanks to @Ukhellfire and @going. Downloadable here: https://xogium.performanceservers.nl/archive/orangepi3-lts/archive/ Below is what I find the status is for the new Armbian 23 images provided for here : https://www.armbian.com/orangepi3-lts/ Branch current: Main downloads Armbian 23 with kernel 6.1 bookworm: It boots, but every 3rd or 4th keystroke is ignored. No ETH, no WiFi. Armbian 23 with kernel 6.1 jammy: It boots, keystrokes are OK, ETH is OK, but WiFi doesn't work. Branch edge: Rolling release…

Hi, I'm migrating from the OrangePi image to Armbian, and can't make the touchscreen working, it does not respond to any actions. It works pretty well on the OrangePi's image. Did I mess up something here? uname -a: Linux orangepizero2w 6.6.31-current-sunxi64 #1 SMP Fri May 17 10:02:40 UTC 2024 aarch64 GNU/Linux Touchscreen DTS: /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h616"; fragment@0 { target-path = "/"; __overlay__ { backlight_gpio: backlight_gpio { compatible = "gpio-backlight"; gpios = <&pio 8 14 0>; // PI14 …

Just ran `apt-get dist-upgrade` on my Orange Pi Zero LTS with Debian minimal Armbian, and wireless network is gone (not shown in armbian-config). Tried downgrading to legacy kernel without success. I have not yet tested 24.08 from a fresh Armbian image; I'm probably going to restore previous 24.05 from a saved backup image. Just sharing this issue in case others see the same thing. No errors in dmesg ... $ dmesg | grep xradio [ 12.723829] xradio_wlan mmc1:0001:1: Input buffers: 30 x 1632 bytes [ 12.723867] xradio_wlan mmc1:0001:1: Firmware Label:XR_C01.08.52.58 Jul 19 2018 18:53:57 but wlan0 is unavailable ... $ nmcli device status DEVICE TYPE…

Hi all, I'm trying to put my orange pi zero to talk with a CAN BUS via mcp2515 chip. The chip is SPI controlled. The actual image does not have support for SocketCAN enabled, so I'm compiling the kernel with SocketCan following the kernel configuration shown here https://developer.ridgerun.com/wiki/index.php/How_to_configure_and_use_CAN_bus I'm using the cross-compiler tool from the armian website. After the image is burned to the sdcard and the orange pi zero is booted, I can see the image has can support enabled, but when I load the mcp251x driver it does nothing. I'm sure I'm missing some detail on spi side in order to have the mcp driver pointing to th…

Hello I am using Orange Pi Zero 3 and I installed the latest armbian version on it I have the picture through HDMI, but there is no sound!!! Isn't one of the main uses of these boards multimedia?! Why shouldn't this board have sound?!!! I have checked all the settings. Thank you. If there is a way, please help me My armbian version: Armbian_community_24.5.0-trunk.667_Orangepizero3_jammy_current_6.6.31_gnome_desktop

I want to modify the antenna strength of wlan0 in orangepipcplus, but using software settings does not work.

Hi. I'm having network problems at last armbian (Armbian_community_24.11.0-trunk.130_Orangepi3_bookworm_current_6.6.44_minimal). Link drops ethernet RTL8211E all the time and sometimes board won't come out of reboot. Any ideas? [ 2.392800] dwmac-sun8i 5020000.ethernet: IRQ eth_wake_irq not found [ 2.392834] dwmac-sun8i 5020000.ethernet: IRQ eth_lpi not found [ 2.393489] dwmac-sun8i 5020000.ethernet: PTP uses main clock [ 2.393545] dwmac-sun8i 5020000.ethernet: Current syscon value is not the default 58000 (expect 50000) [ 2.405541] usb 2-1: USB disconnect, device number 2 [ 2.501691] dwmac-sun8i 5020000.ethernet: No HW DMA feature register supported …

I used armbian-config to set up boot from EMMC. Then I run dd if=/dev/zero of=/dev/mmcblk0 bs=1024 count=2048 And re-partitioned my SD Card. Rebooting with or without SD Card not possible.

I believe that ethernet adaptor is not working properly because there's only one led blinking and its unable to receive ip address. I have tried to configure it with yaml files and manually with networkd and with static ip. I also tried to run dhcp on that interface and it received random ip outside of my network. Had no luck with network-manager either, it threw an error "ip configuration could not be reserved" With desktop image ethernet worked with no problem. So maybe there's a driver issue?

I am using orange pi pc plus after using armbian system, there is an infinite network with WLAN0 and WLAN1, but at present there is no law to use both networks at the same time and connect different SSIDs. Error: Connection activation failed: (7) Secrets were required, but not provided. pi@orangepipcplus:~$ cat /etc/os-release PRETTY_NAME="Armbian 24.5.0-trunk.512 jammy" NAME="Ubuntu" VERSION_ID="22.04" VERSION="22.04.4 LTS (Jammy Jellyfish)" VERSION_CODENAME=jammy ID=ubuntu ID_LIKE=debian HOME_URL="https://www.armbian.com" SUPPORT_URL="https://forum.armbian.com" BUG_REPORT_URL="https://www.armbian.com/bugs" PRIVACY_POLICY_URL="https://www.armbian.co…

Hi you all. I'm trying for a couple of day now to solve an annoying problem with the USB and some Bananapi M2 zeros. I have two cluster-hats with 4 Bananapi M2 zeros as nodes. The cluster hat presents itself as a USB gadget (USB ethernet interface) to the nodes allowing networking between the controller and the nodes. The nodes work fine with kernel 5.9.8, the modules identify the hat as a network interface and everything works as expected. My trouble is that I'm creating new images for the nodes (bananapi m2 zero) from here, the nodes boots, but it seems like the OTG port is not behaving as expected. Followed instructions from these posts:…

Hello, I have a fully working customized Armbian on OrangePi PC Plus. There are two partitions, one for the rootfs, second mounted as /home I want to convert the root partition to squashfs, and use the squashfs file to boot from. I already converted the root partition to squashfs file, I can mount squashfs file, and the contents are correct. I even tried to mount it via fstab and it works. I searched everywhere, obviosly not enough, but I cannot find a way to boot directly from the squashfs file. The idea is to have only squashfs file and rw partition for /home Please, can somebody help me, or point me to the right instructions ?

Hi Managed to get x11 to boot in latest armbian desktop Ubuntu gnome build x11vnc runs when manually running it fine but how many tutorials I have followed online it refuses to start as a service (auto) always gets bad access error when trying to get xauthority I guess ,even when I point it to the .xauthority files with -auth and used -auth guess tried all theses Tutorial 1 Tutorial 2 Tutorial 3 plus videos on YouTube has anyone got vnc to run on orange pi zero 3 Ubuntu noble gnome desktop From here at start up on x11? thanks

Hi, Running on Armbian_community 24.8.0-trunk.529 Bookworm with Linux 6.6.43-current-sunxi64 onthe orangepi zero3 And need to use the GPIO pins with python, not an expert here but have tried a few recommandations with no luck. Can anyone suggest method that works with the above OS/build please? Thanks! Rob.

I built an image for the `orangepi-z-2w` via `./compile.sh build BOARD=orangepizero2w BRANCH=current BUILD_DESKTOP=no BUILD_MINIMAL=no KERNEL_CONFIGURE=no RELEASE=bookworm`. The wifi connects (shows as active), however, I am unable to get on the internet (pinging results in `network is unreachable`, also can't ping the device itself). Am I building wrong? Thanks! Some notes: - I've been using `Armbian_24.2.6_Orangepizero2w_bookworm_current_6.6.28.img.xz` in the past (downloaded from armbian.com), and the wifi works just fine.

I have an ap in banana pi whose ip is 192.168.4.1. And eth0 on banana pi whose static ip is 192.168.144.100. I would like to connect device A from banana pi's ap and also it can ping to the eth0. So far I had tried: sudo iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE sudo iptables -A FORWARD -i wlan0 -o eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT sudo iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT

How to install Home Assistant Supervised on Armbian 23.02 Jammy (plus minus, but quite installed on the previous release of Armbian, this is based on Debian 10) Performed exclusively without a graphical interface, from the console. Works stably on Orange Pi Lite , including a connected Bluetooth dongle via USB and sensors to it. 1. The first installation of Armbian and the subsequent creation of a user and passwords, the next is required to install all updates via sudo apt update && sudo apt upgrade -y . Then you need to install the Firmware update through the armbian-config ->System utility as in the screenshot. Скрытый текст …

Hi - is there anywhere a working guide to create a Wifi Access Point with this board ? I have tried the official debian ISO from orange pi and doing so with create_ap is very easy. I'd like to use armbian instead but using the "Minimal / IOT image with Armbian Linux v6.6" (bookworm) all I get is hell: I installed network-manager and armbian-config then used the later to try the hotspot configuration but then (several freezes and reboots after) it complains that "Unit hostapd.service is masked" and when I solve that, then dnsmasq fails and I see no helpful error message. I even tried connecting to a wifi network first before trying hot…

Hello, I've got some problems with a Cubietruck. First thing to state is that the com-port apparently has died. It was connected via a USB-converter 3,3v and worked flawlessly for a long time. I replaced it with a new one but no go. In the beginning no problem, I could use SSH. Second thing is that the hard disk became erroneous. I bought a bigger model but no boot. I thought that the UUID-entry in /etc/fstab caused this and changed it via tune2fs to the old one, but still no boot. Thus I could no longer use SSH! And I cannot mount the old harddisk, it's to erroneous! Third thing is that I tried with a new image, and the cubie seems to fina…