Rockchip

Hello, download page for odroid M1 states: I have two questions: - Does that mean that the system will be installed on SD or eMMC? or does that meant booting on SD is just for startup to launch system stored on NVMe (or any other storage)? - Is there a plan for booting from M.2 NVMe M-Key PCIe3.0 2-Lane in the future? Thanks Julien

When using the "boot from SD install to NVMe" option of armbian-config it offered the option to format the NVMe drive with btrfs. When I selected that option, it briefly flashed an error about the partition being too small (even though I had created a 120GB partition). The actual problem appears to have been that btrfs-progs was not installed. After installing that package and rerunning armbian-config it was possible to btrfs format and install successfully. I suggest the error message could be improved. Armbian_22.11.1_Rockpi-4cplus_jammy_current_5.15.80_minimal.img.xz

Would anyone be able to help me out with instructions for installing armbian to the EMMC of my Rock Pi N10? I've had Ubuntu installed using the OTG tool and also Armbian running off an SD card, but as soon as I run armbian-install and reboot the device doesn't come back up. Not sure what I'm doing wrong or the correct steps to troubleshoot.

I just saw the post how to get kodi working with a legacy kernel. I want to get ffmpeg working in a docker (specifically for frigate). Do i also need to install the legacy kernel on my machine and do the same steps and only then get the ffmpeg installed in the docker or can anyone help me how to start with this.

Rockchip has released bsp kernel 5.10 for rk356x and rk3588. Since multimedia support is not fully supported by mainline kernel, a legacy kernel would be good if you want h264/hevc hardware decode. To make kodi support hardware decoding, you need: 1, ffmpeg supporting rkmpp. I've packaged it in my ppa: https://launchpad.net/~liujianfeng1994/+archive/ubuntu/rockchip-multimedia, which is based on the patch from https://github.com/JeffyCN/FFmpeg/. 2, kodi built with gles render system, which is also in my ppa 3, a gpu driver supporting gles. For rk356x you can use mainline panfrost driver. For rk3588 you can use panfork-mesa from my ppa: https://launchpad…

Hi, my current CI build fails, and i cannot make up, whats wrong with it. It was working previously until i moved my project within the GitLab instance to another folder. Now i'm getting the following errors: tail output.log OBJCOPY lib/efi_loader/dtbdump.efi CC lib/vsprintf.o CC lib/strto.o CC lib/abuf.o OBJCOPY lib/efi_loader/initrddump.efi CC lib/date.o CC lib/rtc-lib.o CC lib/elf.o AR lib/built-in.o [ error ] ERROR in function compile_uboot [ functions/cli/cli-entrypoint.sh:109 -> functions/main/build-tasks.sh:261 -> functions/main/build-tasks.sh:128 -> functions/compilation/uboot.sh:13…

I am trying to provision QEmu/KVM to run a Kubernetes cluster based on Ubuntu Cloud Image instances. I am using the latest release of Armbian on 16GB Rock 5B. Release kernel. After a relatively smooth setup I am able to provision and run instances. virt-install --connect qemu:///system --virt-type kvm --name virt1 --ram 2048 --vcpus=2 --os-variant ubuntu22.04 --disk path=/root/VMImages/virt1/virt1.qcow2,device=disk --disk path=/root/VMImages/virt1/virt1-seed.qcow2,device=disk --import --network network=default,model=virtio,mac=$MAC_ADDR --noautoconsole Everything works and I am able to log into the instance, but for some reason I am see…

I tried to install Armbian_22.11.0-trunk_Rockpi-4b_bullseye_current_5.15.76_minimal.img.xz from https://github.com/radxa-build/rock-pi-4b/releases/tag/20221101-0235 After first reboot main partition goes readonly. Checking disk show free cluster records mismatch. It is not SD-card issue, because Ubuntu Server on same SD-card working perfectly.

I installed tvheadend on Armbian 22.08 Jammy and Bullseye using the 5.15 kernel. Tvheadend runs fine for a while and then freezes and disconnects filling the log file with the following message: rock64 kernel : au0828: recv_control_msg() Failed receiving control message, error -71. At first I thought it was a problem with Jammy, but I still had the same problem on Bullseye. So I switched to the legacy kernel 4.4.213-rockchip64 and I do not have the problem. I am using a Rock64 Ver. 2 with usb dvb tuner for tvheadend and it is stable running Bullseye with kernel 4.4.213. I am not sure what changed between these kernel ve…

tried several armbian images with kernel 5.15.76, no success! even tried to disable SPI flash, although radxa says "no SPI Flash on the board" in contrast to the 4B version official 4.4 radxa image is booting: rockpi-4b-debian-bullseye-xfce4-arm64-20221109-1447-gpt.img can someone send me armbian bullseye image with older kernel?

Have an OPi 4B with installed Armbian (Armbian_21.05.1_Orangepi4_buster_legacy_4.4.213_xfce_desktop.img from here) which is working perfectly. HUGE thanks for that. So i wanted to try images with mainline kernel and found that none of XFCE desktop images from the archive can correctly output HDMI signal for my screen, maximum i could achive was compressed and flickering image using method from docs (editing /etc/X11/xorg.conf.d/40-monitor.conf). by default there are no modes in /sys/class/drm/card0-HDMI-A-1/modes in mainline images and in legacy one there are two: 1280x800p60 and 1280x800p57. EDID is there in both images. And if i set resolution via /…

Those are developers preview builds, where you can check what works and at some point it will be good enough for some uses cases. In a couple of years, it will be functional on the level of kernel 5.10.y. Download is possible from CI pipeline: https://github.com/armbian/build/releases Boot log: Spoiler [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000] Linux version 6.1.0-rc1-rockchip64 (root@desktop) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.…

Hello, Devices: RockPi 4b v1.5 + remotable eMMC + NVMe KingSpec M.2 NMVe SSD NE 2280 512 GB I am using instructions to erase SPI https://wiki.radxa.com/Rockpi4/dev/spi-install $ sudo rkdeveloptool ld DevNo=1 Vid=0x2207,Pid=0x330c,LocationID=103 Maskrom $ sudo rkdeveloptool db ./rk3399_loader_spinor_v1.20.126.bin Downloading bootloader succeeded. $ dd if=/dev/zero of=./zero.img bs=1M count=4 4+0 records in 4+0 records out 4194304 bytes (4.2 MB, 4.0 MiB) copied, 0.0160027 s, 262 MB/s $ sudo rkdeveloptool wl 0 ./zero.img Write LBA from file (100%) $ sudo rkdeveloptool td Test Device OK. $ sudo rkdeveloptool rd Reset Dev…

With Linux rock-5b 5.10.72-rockchip-rk3588 #trunk.0102 SMP Sat Nov 5 07:56:18 UTC 2022 aarch64 GNU/Linux I see only one PWM controller pi@rock-5b:~$ ls /sys/class/pwm/pwmchip1/ device export npwm power subsystem uevent unexport pi@rock-5b:~$ cat /sys/class/pwm/pwmchip1/npwm 1 How do I figure out its header pin assignment? Is there a device tree overlay to expose all 4 PWM controllers?

Hi, community! I wish you have a nice day! Started investigating why do I have problems trying to hear something from headphones. So, I believe there is something about HDMI audio codec related to panfrost, attached you will find info about. I guess this will be useful to catch bugs. I'm 73 years old, started on computers on NCR Century 100 as field engineer. From those years to now, a long development has brought to life.... Cheers, and many thanks to you! dmesg112222.txt armbianmonitor112122.txt

Hi My problem is that armbian 6.0.7 kernel hasn't recognised my 28" samsung 4k monitor.It recognised like a 29" monitor.How can I fix this problem? and in 4k resolution right of the screen doesn't show properly.In this side of the screen is completely white. Another problem is that 4k video plays very slowly How can I fix this problem? Thank you for your answers!

Hi, I try official Sid image found at https://www.armbian.com/station-m1/ and can't activate bluetooth on my Station M1 : root@station-m1:~# hciconfig hci0: Type: Primary Bus: UART BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0 DOWN RX bytes:106 acl:0 sco:0 events:2 errors:0 TX bytes:100 acl:0 sco:0 commands:2 errors:0 root@station-m1:~# hciconfig hci0 up Can't init device hci0: No such file or directory (2) It seems the firmware of rtl8723ds doesn't load : [ 14.182722] Bluetooth: hci0: RTL: examining hci_ver=08 hci_rev=000d lmp_ver=08 lmp_subver=8723 [ 14.193986] Bluetooth: hci0: RTL: rom_version status=0 version…

Hello, i am pretty new to arm embedded. I have a Rock64 V3.0 2019-0626 So I downloaded Armbian 22.08 Jammy XFCE from https://www.armbian.com/rock64/ and copied it on a 265GB SanDisk Extreme microsd XC 1 V30 A2 using Balena Etcher. Boot process did work, but startxfc4 did not work. The system just went on a blackscreen, but i could still switch to another terminal with alt+f1 ... Best regards, Bo

I downloaded the latest Armbian 22.08 image for the NanoPi M4V2 (https://armbian.chi.auroradev.org/dl/nanopim4v2/archive/Armbian_22.08.8_Nanopim4v2_jammy_current_5.15.75.img.xz), flashed it to an sd card and tried to boot my NanoPi M4 (non-V2 board). It crashes every time with the attached log. I have tried 4 different power supplies, so I don't think that's the issue. I tried the Bullseye CLI image and it fails in the same way. The Sid server image works fine. Any ideas? Thanks, Ben

The link to nightly builds for the Rockpi 4C+ WIP on https://www.armbian.com/rockpi4/ is broken. (Perhaps it should link directly to https://github.com/armbian/community ?)

Hello, I am new to this forum and struggling with some stuff on the Tinkerboard S R2.0. I use the CLI-version of Armbian Jammy of 23 october 2022. I have to activate several features. I think two of them might relate to 'missing firmware'. 1. Activating a AccessPoint: during the installation of raspAP I get a set of error on 'missing firmware'. 2. Installing a modem: not a single USB-device gets recognized by lsusb. I am stuck at the very beginning. lsusb is working on the xfce but we want a leaner system. I tried the latest TinkerOS but I require a more updated version of python (3.10) and I also would like to stick t…

I have a problem with touch screen, i must each time after power on calibrate touch screen. Looks like dont save parameters. Any help?

Hi folks, I have a Firefly AIO-3399C which boots Armbian fine, but no USB devices besides the root devices are detected. This happens with both the kernel 5.19.170 and 6.0.7 based images, made by @balbes150, which I've downloaded from https://users.armbian.com/balbes150/firefly-rk3399/ Any advice would be appreciated. U-Boot 2022.04-armbian (Nov 03 2022 - 17:26:20 +0300) Linux firefly-rk3399 5.19.17-media #trunk SMP PREEMPT Thu Nov 3 17:40:36 MSK 2022 aarch64 aarch64 aarch64 GNU/Linux In dmesg output, I see the following, which may be relevant: [ 4.616394] hub 7-0:1.0: USB hub found [ 14.296598] fusb30x: module is from the sta…

lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 11 (bullseye) Release: 11 Codename: bullseye hwinfo --disk 20: PCI 00.0: 10600 Disk [Created at block.245] Unique ID: wLCS.EJHvc9MwvZ7 Parent ID: VCu0.AxGd7hiuG+6 SysFS ID: /class/block/nvme0n1 SysFS BusID: nvme0 SysFS Device Link: /devices/platform/f8000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/nvme/nvme0 Hardware Class: disk Model: "Samsung Electronics NVMe SSD Controller SM981/PM981/PM983" Vendor: pci 0x144d "Samsung Electronics Co Ltd" Device: pci 0xa808 "NVMe SSD Controller SM981/PM981/PM983" …

hi everyone How can I activate the SPI in the nanopi neo3 board?

https://www.armbian.com/odroid-m1/ - kernel 6.1.y LTS

Hi, My NanoPi M4 V2 Won't Boot via SD ... the emmc is not installed on the board The RED light is ON but the GREEN stay OFF I cannot reached to read correctly the data coming from the serial port debug (I tested with many bauderate, also with 1500000, same result ... a lot of weird characters) Tested Versions Won't boot: Armbian_22.08.1_Nanopim4v2_jammy_current_5.15.63.img.xz Armbian_22.08.1_Nanopim4v2_bullseye_current_5.15.63.img.xz Armbian_22.11.0-trunk_Nanopim4v2_sid_edge_6.0.3.img.xz Armbian_22.11.0-trunk_Nanopim4v2_kinetic_edge_6.0.3.img.xz Tested Version Boot properly: Armbian_21.02.1_Na…

Hello everyone, I'm running the image from NanoPi R2S on a NanoPi R2C Plus (that has 8 GB eMMC). Is well working, but I would like to install the OS on the eMMC. Is it possible? Thanks.

after several minutes, a 3 line error message is output on 2 old original rock64's. network works, I can log in from my local net, and dmesg says: [ 35.867400] Unbalanced IRQ 47 wake disable [ 35.867422] WARNING: CPU: 0 PID: 1580 at kernel/irq/manage.c:900 irq_set_irq_wake+0x108/0x148 [ 35.867447] Modules linked in: rfkill joydev snd_soc_spdif_tx gpio_ir_recv rc_core lz4hc cdc_acm lz4 hantro_vpu(C) rockchip_vdec(C) rockchip_iep snd_soc_simple_card v4l2_h264 snd_soc_rockchip_i2s rockchip_rga videobuf2_dma_contig snd_soc_rockchip_pcm snd_soc_hdmi_codec snd_soc_rk3328 snd_soc_simple_card_utils v4l2_mem2mem snd_soc_rockchip_spdif videobuf2_dma_sg videobuf2_vmal…

Picked up a P1 Pro the other day. Used the P1 installer, and it boots fine. However WiFi and m.2 dont work ( no m.2 makes it useless for me.. WiFi, i can use a dongle ) so i assume the device tree needs changed. Still a newbie at this, so unsure how i can find or extract the tree from somewhere else. They do have a couple of official builds of other OS, but not real sure how to get it from there, if you even can. Lots of googling for a tree has come up empty.

By pure accident, I discovered that Ctrl-Alt-F1 while the P2 is booting brings up more options on mine that allows the deletion of firmware and clearing of emmc. I have not done it but the menus are there.

OS: Armbian_22.11.0 (5.15.71) for RockPi-4C HW: RockPi-4C I would like shared my eth0 connection via integrated wlan0 adapter. I have do all steps stated here: https://linuxhint.com/create-wifi-hotspot-linux-mint/ but when I try to connect my notebook to the hotspot wlan, notebook does not get proper IP address and so a internet sharing does not work . Any ideas to solve this problem?

OS: Armbian_22.11.0 (5.15.71) for RockPi-4C HW: RockPi-4C I would like shared my eth0 connection via integrated wlan0 adapter. I have do all steps stated here: https://linuxhint.com/create-wifi-hotspot-linux-mint/ but when I try to connect my notebook to the hotspot wlan, notebook does not get proper IP address and so a internet sharing does not work . Any ideas to solve this problem?

6 days ago I did a usual "apt-get update && apt-get upgrade" which brought up the following output: rock@rock-3a:~$ sudo apt-get update && sudo apt-get upgrade && sudo apt-get -y autoremove && sudo apt-get -y autoclean OK:1 http://deb.debian.org/debian bullseye InRelease OK:2 http://deb.debian.org/debian bullseye-updates InRelease OK:3 http://security.debian.org bullseye-security InRelease OK:5 http://deb.debian.org/debian bullseye-backports InRelease OK:4 https://box64.debian.ryanfortner.dev/debian ./ InRelease …

Hello, I recently bought a Rock 3A and trying to use Armbian, I am very newbie in this area. I tried few options available (22.08.2 Jammy & Sid) for Rock 3A from here but in all of them the boot fails and falls into endless initramfs Can you give me a hint what could be cause of this?

Hello all, I am trying to interface with the MCP2515 on SPI2 of the RockPi4B on Armbian 22.08.6 Bullseye with Linux 5.15.74-rockchip64 and encountering some issues. The rockpi4B pins that I am using to connect to the MCP2515 INT - GPIO2_A7 MOSI - GPIO2_B2 MISO - GPIO2_B1 CLK - GPIO2_B3 CS - GPIO2_B4 When using the overlay file that I have shown below, the output for "dmesg | grep mcp": [ 6.662536] rockchip-pinctrl pinctrl: unable to find group for node mcp2515_int_pin I have been able to get the MCP2515 to initialize successfully, but only if I comment out the pinctrl-0 reference to the mc…

I can use echo 0 >/sys/class/leds/status/brightness to turn off the status led (blinking blue one, but I was to turn off the bright ass green one. I assume this is mmc1::, but I cannot turn it off.

I'm trying to get this rockpro64 board to boot off of pxe/nfs. I'm able to get it to boot into armbian and to the point where it asks for the new root password. But something happens on the device where the network gets disabled which stops the NFS connectivity and the rest of the system with it. All traffic stops on the device and it becomes unreachable. NFS traffic stops, it no longer responds to pings, etc. It's not entirely frozen, for example it prints kernel messages to console if the ethernet is pulled. And after a few minutes the nfs connection times out and it starts printing this over and over. It always happens about 75 seconds…

Just a reminder, if someone wants to fix it.

I simply can not figure out why UART4 at GPIO1 header with the pins 19 (TX) and 21 (RX) not working at all. I see that here (ttyS2) is running an agetty but there is no serial activity at any baudrate (9600, 115200). Please help me.

Hi guys. I've been working with the 4.19 kernel before on M2. I upgraded to the kernel version 5.18 today. I found that I can't find the registered udc device anymore. This is auto-registered on the 4.19 kernel and you can find it under /sys/class/udc. root@station-m2:/boot# ls /sys/class/udc fcc00000.dwc3 I would like to ask how to enable the udc device on the 5.18 kernel. Thank you.

Howdy With a p2 that already had ubuntu installed on the ssd using the firefly technique, it seemed time to upgrade using to armbian. Installing the new uboot went fine. It is not clear how to confirm it. The command did not error. However using the jammy 22.08 images, the uuid does not appear to be on the SD card. At this time I do not have a serial cable. However the image shows sum of the situation. Any help appreciated including advice on rj45 to serial cable. Thanks.

https://www.armbian.com/rock-5b/

Is there a method to boot with BSP kernel (the 4.4 kernel supplied by Rockchip/Radxa) on an existing install (jammy) to compare power usage to mainline kernel (5.15.y current or even 5.19.y rolling)? I tried using the switch kernel support in armbian-config, but the linux-image-legacy-rockchip64 4.4.213-rockchip64 just hung during early boot and had to recover to linux-image-current-rockchip64 5.15.69 . P.S. This is related to my question on the Radxa forums about reducing Rock Pi 4 B+ power usage.

Whats the SSH password? i plugged it in and can see the device grab an IP but the default username "pi" and password "armbian" does not work when attempting to ssh in.

Hello everyone, i was thinking about running a jellyfin server on the Rock64, is there any chance for hardware encoding? Thank you in advance Regards

Dear all I have a question concerning the Tinker Board video playback function. Until now I used some raspberry PIs 3b to create a simple system that video playbacks in loop after booting for my video installations. Now as the raspberries are not in stock at the moment but i need very urgently another working system, i saw that i can buy the tinker board 2.0 for a reasonable price. However, I'm not a programming specialist and was happy when I got the raspberry to run, I couldn't found anything about the tinker board and specially about a video loop function. I imagine that it is possible, just wondering how complicated it is. Can someone tell me …

System logs: http://ix.io/4bd2 I have been using Armbian OS with Rock Pi 4B. The problem with Rock Pi 4B is that it doesn't have a power-on/off button. So, for closed systems with no keyboard/UI, there is no way to shutdown/start the system properly. Only option is to disconnect the power cable, which has corrupted my OS few times(by the way didn't happen on Debian). I implemented shutdown function through MRAA library and by attaching a button to 40-pin GPIO header. But with this approach, system can go to sleep, but cannot wake-up through button because my software is not running. As I have understood, the best approach to have a proper button f…

I planned to upgrade and skip current 5.18 (EOL) with edge 5.19 or just use LTS 5.15. Offcial images 5.19/edge (e.g. Armbian_22.08.1_Nanopct4_sid_edge_5.19.5.img.xz) won't boot at all, maybe a short uboot screen. Using uboot v22.04 like other rk3399 boards did not fix it. SInce the nanopct4.conf is boardfamily=media but also works with rockchip64 (which was changed some time ago), building with boardfamily=rockchip64 current 5.15 or edge 5.19 works fine, the cli builds boot as expected. Maybe a general question, which bordfamily fits now best to nanopct4. I remember exactly problems which were fixed bei 150balbes maintainer when pul…

I will show you how I successfully enabled pcie gen2 on my Rock Pi 4b and now my nvme is running at 1.1 GB/s. The solution which you can find on the web to activate pcie gen2 on an Armbian did NOT work for me: sudo nano /boot/armbianEnv.txt and insert: dtoverlay=pcie-gen2 The following solution activated pcie gen2: 0. check your current nvme speed to compare it afterwards with: sudo dd if=/dev/nvme0n1 of=/dev/null bs=1M count=2048 iflag=direct status=progress --> 618 MB/s 1. find out which rk3399-rock-pi-xxx.dtb your Rock Pi 4 is using. cat /boot/armbianEnv.txt | grep fdtfile --&g…

This feels really awkward, since I already asked about this problem in another part of the forum, but the bug reporting system says that bugs should be reported by posting in this section of the forum. Feel free to merge the other thread into this one if you want. (Link at bottom.) Linux kernel 5.15.x appears to have a serious regression that prevents GPIO from working correctly on the Rock Pi 4B+ (board version 1.73). Summary: All GPIO4A pins are nonfunctional: Pin 12 stuck off Pin 35 stuck off Pin 36 stuck off Pin 38 stuck off Pin 40 stuck off GPIO1B is nonfunctiona…

Hi there ... Not sure if anyone has an idea here, but I have the following topic: I have a helios64, equipped with 3 2.5" disk drives, running Debian 10 with Kernel 5.10.43. Usually the system runs stable ... even for days (24/7). But every now and then the disks "fail" - which means, during normal operation suddenly the disk turn of, linux reports "sata link down" ... and the disks are off. As if they were removed. If I reboot I usually here only some "klicks" ... I assume the disks try to spin up, but fail due to not enough power (?). To recover from that situation, I usually disconnect power (incl. the internal UPS) ... try a few times, and …

Actuaylly, I have a two problem. First is, If I print large outputs, It's out was unpredictable. $PS1 randomly added ...snip... ], "locs": [ "ALX", "SOP", "PNX", "NYC" ], "jbound": "0.010000", "tbound": "0.05" } ] } 20220908.04:53:56 root@openskyr2s:~# , <<<<<<--------------------- really randomly appeared my $PS1 in output / Even I use less/more, it sometimes happens. "val1": 4, "val2": 0, "subkey1": [ "blah" ], "filters": [ ...snip... Second is, Prints large outputs(jq , cat) to default console few times, I …

Hello, I am quite new to armbian build system. I have rock pi s v13 hardware. I want to change the default UART2 serial console port in Armbian for Rock Pi s to UART0. The reason is I need hardware flow control with one of my serial port. And UART1's RTS/CTS are muxed with UART2. And no other port exposed on Rock Pi s have the hardware flow control pins. Please guide me how I can achieve this.

Hello, I have been using Armbian OS on Rock Pi 4B. Full system is on NVME, not using SD card, and there is no eMMC chip on the board. During usage, I needed to shut it down improperly: by removing power cable, not through sudo shutdown now In the end I have following message during boot: Also, here is contents of dev folder: I was wondering if it is possible to fix this error. If not, I will reinstall with new image. Just spent much time on setting the environment, don't want to redo this all I would appreciate any help.

Hi, i'm trying to compile an u-boot for my Rock-PI 4B. I wanted to apply a userpatch, that disables the uart debug console in u-boot. I seem to have an issue when using the Rock-PI together with a weather-sensor via RS485-Hat. Here is my patch: diff --git a/configs/rock-pi-4-rk3399_defconfig b/configs/rock-pi-4-rk3399_defconfig index be07b16bae..63d04ced6e 100644 --- a/configs/rock-pi-4-rk3399_defconfig +++ b/configs/rock-pi-4-rk3399_defconfig @@ -13,7 +13,7 @@ CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI=y -CONFIG_DEBUG_UART=y +CONFIG_DEBUG_UART=n CONFIG_SYS_LOAD_ADDR=0x800800 # CONFIG_ANDROID_BOOT_…

Hi, i'm currently trying to disable the serial console on port 2 on my Rockchip based Rockpi 4B (based on rk3399). I already found the following forum thread, that describes in brief, that i basically have to recompile my own armbian image. But still I'm missing some information. I have read the docs in docs.armbian.com and watched the YouTube video on how to build an armbian image. So far, i was able to setup a VM for building an image on my workstation. I also had a successful compile run yesterday, that created some output in my output folder. Now, I'd like to apply a patch, that changes the serial debugging console during boot from port 2 to port 4. …

The NanoPi R4SE is similar to the NanoPi R5S. Would love to have an Armbian image for it.

Hi, Have the r2s for some time and it worked well in the beginning. But then it started to freeze randomly. The logs do not have any error in it. Initially I thought it could be the interface drive problem, changed the interface and still freezes. When the r2s is frozen, serial port won't respond. Keeping serial connection and restarting the r2s, boot messages show normally. When I keep the serial connected, r2s do not freeze (tried for more than a week). Found this other post, not sure if this is the same problem as it does boot, but seems related. mUSB serial connection rarely works. Have to boot some times until it works. Although I am an exp…

I get no audio devices in Gnome/Jammy userland on an Armbian 5.18 kernel. From the console, alsamixer has controls for Analog RK809, but no Playback Mux for the speaker (mini jack) and changing the card Default to HDMI reports "This Sound Device Does Not Have Any Controls". The Gnome/Ubuntu audio applet has only a dummy device. Thanks!

The instructions at the P2 page cannot be followed. The image at the link does not contain the p2-station-update-uboot script. I have tried using the Station OS multi-boot thing but that didn't work either. What is the correct way to do it now?

Hi all, I have a nanopi m4 with following installation - Armbian_22.05.4_Nanopim4v2_jammy_current_5.15.48_xfce_desktop. I am looking for someone who has retroarch installed on armbian and fully working, and what the key steps are. Im asking because: 1) I tried installing by command line, which installs retroarch to a location with no cores. An issue with rk3399 cores is that there are none to download and must be built seperately (Is there a way to update a file so that cores can be downloaded through the application?) 2) In an attempt to build retroarch + cores, i downloaded and built libretro, which took probab…

(Note: this is crossposted from an ATS issue, since I think it might be quicker to get answers here. Will post on one thread when I get answers that work in the other) Have installed ats on my Rock64, running Armbian 22.05 Jammy with kernel version 5.10.63, and am having trouble getting the fan to spin. The fan I'm using is the one that comes with this case, and it spins when I connect it to a battery. One possible issue is that I had to manually add an entry for PWM_CTL: running sudo find /sys -name pwm\*, I get: /sys/kernel/tracing/events/pwm /sys/kernel/tracing/events/pwm/pwm_apply /sys/kernel/tracing/events/pwm/pwm_get /sys/kernel/debug/tracing/events/p…

The first version of Armbian images for Station M3 rk3588s (rk3588s-roc-pc) is available. the launch is very simple - download, unpack, burn to an SD card, connect to the device and turn on the power. The system starts automatically. At the first launch, perform the initial setup in the same way as all Armbian-enabled devices. https://disk.yandex.ru/d/-zSW21XKN0pfIA

I'm not sure this is right place to submit libgnutls30 armbian package issues. If anyone libgnutls30 to 3.6.7.4-deb10u9, you may have trouble to connect some SSL destinations. I revert it back to 10u7, then problem was gone. 20220817.05:18:10 root@armbianr2s:~/lkm# echo -e "GET / HTTP/1.1\n\n\n" | openssl s_client -connect web.telegram.org:443 -tlsextdebug CONNECTED(00000003) ^C 20220817.05:18:47 root@armbianr2s:~/lkm# #SSL_CONNECTION_PROBLEM_SOME_SITES_AFTER_UPGRADE_libgnutls30_THEN_REBOOT; 20220817.05:19:03 root@armbianr2s:~/lkm# #PROBLEM_ALSO_HAPPENED_WHILE_tcptraceroute_THEREFORE_I_WAS_REALLY_CONFUSED_AND_WASTED_TIME. BECAUSE, tcptrace and python N…

Dear Forum, I am using a Helios64 with armbian Debian 10 (Buster) Linux-Kernel 5.15.52 and OMV 5.6.26-1. If I want to have further Updates from OMV I need to upgrade to Debian 11, because OMV6 isn't compatible to Buster. Any recomendations how I should upgrade? The H64-System is on a SDD. Should I try a cli system upgrade or installing everything new with a bullseye image, if this is available (Where?)? Best wishes, Greg

Hello everybody! From what I found there’s no rockchip64 (is that the right one for rk3568?) header for 5.10.110. Since the current Kernel is that version can somebody help me either build or point me to right header files? That would be much appreciated

Running latest Jammy image and trying to attach USB to SATA 3 SSD. I tried two different USB 3 to SATA adapters and they both show up in lsusb: Bus 005 Device 002: ID 2109:0711 VIA Labs, Inc. VL711 SATA 6Gb/s bridge sudo fdisk -l doesn't show drive, but I can plug into my desktop and it mounts disk. Could be related to https://github.com/MichaIng/DietPi/issues/5378

Hello, I installed Armbian 22.05.3 Jammy on a Rock Pi 4A+. Unfortunately 3 out of 4 USB ports do not work; only the USB 3.0 OTG port works. I tried using the Debian Buster download from Radxa, and all four ports work. Any suggestion on how to fix this with Armbian?

Hello, I have recently bought a Helios64 item. I have mounted it, I have done all steps written on wiki here https://wiki.kobol.io/helios64/kit/ and here https://wiki.kobol.io/helios64/install/sdcard/ but when I try to follow this steps https://wiki.kobol.io/helios64/install/first-start/ USB to serial bridge is not detected by my notebooks (I have tried with notebook 1 (windows10 x64 with drivers downloaded and installed with exe setup) and notebook 2 (x86 cpu with last kernel ubuntu and windows xp)). I have unmounted the backplane cover, jumper P10, P11 and P13 (see here jumper description https://wiki.kobol.io/helios64/jumper/ ) are all opened so my question is: what is…

Hello everyone, I want to use uart4 port for zigbee2mqtt,but I don't know how to activates it.

I just cannot access spi on my Rock64. I read a couple posts of it but none works out for me I'm running Armbian 22.05.3 Focal with Linux 5.15.52-rockchip64 on it. Tried enabling spi-jedec-nor and spi-spidev overlay, but with none of them I get output when executing ls /dev/spi*. Is it maybe a hardware issue, reading this post suggests that to me: https://forum.pine64.org/showthread.php?tid=5473&pid=34616#pid34616 But I cannot make much sense out of it. Can anyone help me get spi working?

Today I flashed the latest version CLI Jammy img instead of my old OS.First system boot,I can get the IP from my router DHCP and I can ping the Board's IP,but SSH connection refused.Now the Latest System won't start SSH service in first boot?I haven't a monitor,so I cant check the system booted or not.

Hello. I am trying to have the 1-wire working on Rockpi4B+ on pin GPIO4_D6 (= number 158). I have this /boot/armbianEnv.txt: verbosity=1 bootlogo=true overlay_prefix=rockchip fdtfile=rockchip/rk3399-rock-pi-4b.dtb rootdev=UUID=aa1f4e9a-bad9-4760-87c5-511247ef7227 rootfstype=ext4 overlays=w1-gpio param_w1_pin=GPIO4_D6 param_w1_pin_int_pullup=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u but when I check on my board: sudo cat /sys/kernel/debug/gpio GPIOs 0-31, platform/pinctrl, gpio0: gpio-4 ( |bt_default_wake_host) in lo gpio-9 ( |bt_default_reset ) out hi gpio-10 ( |reset …

I hope I am posting this in the right forum ? Just installed Armbian 22.05 Jammy XFCE. No audio either from the main board jack or the HDMI. Tested by playing mp3 with MPV and Celluloid as well as with Chromium Capture from armbianmonitor - U attached below or here http://ix.io/457n Any hints would be appreciated...I don't know how to investigate further this. No_Audio.txt

Hey everyone, i bought a Rock 3A to get an alternative to Raspberri pi. The armbian was the system which is closest to the raspberrian and i'm glad that it works so well. But Videos 720p, 1080p mp4 play horrible bad. When i use the included videoplayer or install vlc and start a video it is laggy and slow and not useable. Is there any additional driver i have to install? Do i have to choose a different encoder? Or is the Rock 3A not capeable of playing Videos? Thank you and best regards.

Armbian version 22.05.3 Focal Nanopi M4V2 There seem to be only default modes available with the nanopiM4V2. Manual adding a resolution does not work (it is added, but has no effect when selected) NanoPIM4V2 Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 4096 x 4096 HDMI-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axi> 1920x1080 60.00* 60.00 50.00 1920x1080i 60.00 50.00 1280x1024 60.02 1280x960 60.00 1280x720 60.00 50.00 1024x768 60.00 800x600 60.32 56.25 720x576 50.00 720x480 59.94 The monitor is a …

Rock 5b test images, from armbian-next. Using vendor u-boot + patches, and vendor kernel, both straight from radxa's git XFCE desktop with "browsers" app group - https://github.com/rpardini/armbian-release/releases/download/20220710b/Armbian_20220710b-rpardini_Rock-5b_jammy_legacy_5.10.66_xfce_desktop.img.xz CLI - https://github.com/rpardini/armbian-release/releases/download/20220710b/Armbian_20220710b-rpardini_Rock-5b_jammy_legacy_5.10.66.img.xz PR: https://github.com/armbian/build/pull/3984 (against master) All work by @amazingfate I just gathered stuff and built images. Thanks to @monkaBlyat @lanefu @piter75 @amaz…

PI-co ITX form factor(2.5 inch, 100 x 72mm) RK3588 powered, 8nm manufacturing process Quad A76 2.4Ghz + Quad A55 1.8Ghz Mali G610MC4 GPU(up to 5 channel 4K UI) 6T NPU 8K 10bit decoder, 8K encoder Support WiFi 6E and BT5.2 Support PCIe 3.0 x4 NVMe SSD Triple display support(with HDR) Two HDMI 2.1up to 8K@60FPS One USB C with DP up to 8K@30FPS HDMI in support up to 4K@60FPS 2.5G Ethernet with PoE support Offer 4GB/8GB/16GB(LPDDR4x) ram options

Hey there, had anyone any success enabling PWM to control a PoE hat [1]? I tried a few overlays but no luck. ``` rock-3a-worker-1:overlay:# cat /boot/armbianEnv.txt verbosity=1 bootlogo=false overlay_prefix=rk35xx fdtfile=rockchip/rk3568-rock-3a.dtb rootdev=UUID=f0751d3c-c5c2-4ced-a989-772c2ad130a4 rootfstype=ext4 overlays=w1-gpio i2c7 i2c8 extraboardargs=nvme_core.default_ps_max_latency_us=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u ``` I also built mraa with the following: ``` IMRAA=ON FTDI4222=OFF BUILDCPP=ON BUILDTESTS=ON BUILDSWIG=ON USBPLAT=ON ONEWIRE=ON INSTALLTOOLS=ON BUILDSWIGPYTHON=…

(only rockpi-4a tag available..) After enabled `rpi-7inch-lcd` overlay, rockpi-4-b-plus doesnt boot, no display, no ip. Before reboot: root@rockpi-4c:/home/qnet# cat /boot/armbianEnv.txt verbosity=1 bootlogo=true overlay_prefix=rockchip fdtfile=rockchip/rk3399-rock-pi-4b.dtb rootdev=UUID=072c27ac-4335-4062-9b8d-a9d0a71d6c3a rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u overlays=rpi-7inch-lcd root@rockpi-4c:/home/qnet# sudo reboot root@rockpi-4c:/home/qnet# Thank you!

I have an orangepi 4b rk3399 board and I am not able to boot with an armbian image above kernel 5.0 . until kernel 4.4.2.1.3 it boots but no usb port works and if you update the kernel it doesn't boot anymore. Can someone help me.

Hi Is it possible to install the system on NMVE M2 ? Or how to completely transfer the SD card OS to NMVEIs it possible to install the system on NMVE M2 ?

Since Linux 5.15, the USB3 port on ROCK64 does not work anymore with Armbian. The following kernel errors are shown: usb 5-1: USB disconnect, device number 2 [...] usb usb5-port1: Cannot enable. Maybe the USB cable is bad? This has been reported by multiple users with multiple drives and cables, also disabling UAS does not help. lsusb shows the drive/device, but lsblk does not. I know the ROCK64 is not currently supported by Armbian/has no maintainer, so I'm not expecting anything, just posting this as information and probably someone with more insights into the rockchip64 kernel build has an idea or workaround.

In distributions that include 4.x series kernels, pcie is detected and the built-in broadcom wireless chip is functional with the wl driver. I would like to move to a 5.x series kernel, but I noticed that pcie is not detected at all, and though wifi is detected with the brcmfmac driver, it will not function to scan or connect to anything. I grabbed the latest image from this week (have tried many previous, including building my own armbian image) but no luck. Has anyone gotten these items to work with a 5 series kernel?

I have a weird issue where I have everything working as I want it a few different services running in docker (Pi-Hole, Motioneye, Home Assistant, Emby) and all their individual management pages are accessible. However as soon as i move the install over to emmc, all networking seems to break, with services no longer working, but some admin pages report everything is fine. Pi-Hole for example shows as running but no devices accessing the dns cant load webpages and the pi-hole management pages stop showing any further queries received. ive repeated the process of doing a clean install to sd , everything fine. move to emmc stops working ☹️

Hello, how to get I2C-2 device support in overlay? I have checked /boot/dtb/rockchip/overlay/README.rockchip-overlays and only i2c-7 and i2c-8 seems to be there. GPIO pins are here GPIO2_A0 and GPIO2_A1 https://wiki.radxa.com/Rockpi4/hardware/gpio#Rock_Pi_4A_.2F_4A_Plus_.2F_4B_.2F_4B_Plus_.2F_4C_.2F_4C_Plus.28.3E.3DV1.2.29_general_purpose_input-output_.28GPIO.29_connector Thank you!

Hi, Is anyone can able to help me with this ? NANOPIM4V2 + OMV and 4xSATA HAT does not boot-up after updating armbian-firmware/buster,buster 22.05.1 Is there any additional info I can get from my system and put here that will help ? Is this the right place to post this ? Thanks ----------------------------------------------------------------------------------- Welcome to Armbian 22.05.1 Buster with Linux 4.4.213-rk3399 System load: 5% Up time: 6 min Memory usage: 6% of 3.72G IP: 192.168.8.60 CPU temp: 37°C Usage of /: 16% of 29G s…

I use orangepi 4B. I use console Ubuntu with kernel 4 from Xunlong And my CPU Temperature (by htop) is about 70°C I use console armbian with kernel 5 (Governor = powersave). And my CPU Temperature is about 79°C Why so? I want to get 70°C in armbian too.

Good morning, I'm using RK3328 SOM-EVB by Olimex with Armbian 22.02.0-trunk with Linux 4.4.213-rockchip64. I'm using it with an HDMI LDC 7" capcaitive touchscreen by Waveshare (https://www.waveshare.com/product/displays/lcd-oled/lcd-oled-1/7inch-hdmi-lcd-h.htm). I can't rotate the LCD in portrait mode. In Application->Screen the "Rotation" section is "none" and there aren't any other choice (like left, right, inverted). If in command line I use: xrandr --output HDMI-1 --rotate left it gives me back: xrandr: output HDMI-1 cannot use rotation "left" reflection "none" Does anybody knows how to solve it and rotate the …

Hi ! Is there any chance to flash an armbian to the 16MB SPI Flash-Chip? regards, volker.

Good job with Armbian, I just can't find the power management, DevTerm A06 has batteries. Maybe I'm blind, please tell me where to look.

Hello. I have this old rk3188 based board with 32gb rom 1gb ram. The arduino is attached for console output. I wanted to install linux in it so i flashed rk3188 armbian to my sd card and it was able to boot up from sdcard successfully. But there is no hdmi signal. I tried to modify dtb file extlinux.conf file but it didnt work. Can anyone figure out what is the problem? This is my extlinux.conf: LABEL Armbian LINUX /boot/zImage INITRD /boot/uInitrd FDT /boot/dtb/rk3188-rbox-cs968.dtb APPEND root=UUID=61de6b0d-dcd6-4049-9fe8-3a15872992b5 console=uart8250,mmio32,0x20064000 console=tty0 …

Hello People. First of all, thank you to all the people that puts work and time into this project. It's my first time posting here. I've been trying to solve this problem by myself since this board it's unsupported now, but I had no luck. The thing it's, I can't get the linux to recognize properly the PlutoSDR, I get this errors in dmesg. [ 19.885514] usb 4-1: new high-speed USB device number 6 using xhci-hcd [ 20.035134] usb 4-1: Dual-Role OTG device on non-HNP port [ 20.035310] usb 4-1: set a_alt_hnp_support failed: -32 [ 20.161463] usb 4-1: new high-speed USB device number 7 using xhci-hcd [ 20.311139] usb 4-1: D…

https://github.com/sigmaris/u-boot First I tried the mainline uboot v2022.04 version and the sigmaris uboot, in the uboot command line I executed the nvme info command and found no nvme devices available. https://github.com/radxa/u-boot Since the radxa version does not have the relevant configuration files for nanopc-t4, the compilation and testing of the radxa version is abandoned. Is the patch in this thread for the mainline v2020.04 release? @piter75 @Hover

Just wondering when an image will be available for the R5S - I have one here sitting waiting for it 🙂

Hi, I tried the new Bullseye image from https://www.armbian.com/station-m1/ to check bluetooth support but nothing is displayed on the screen at boot. No video signal come from the Station M1. The TF card used works with other images. Any hints ? Chris

Bluetooth device does not appear on my armbian (kernel is 5.17.5-media, tried on edge-media and current-media as well). # hciconfig version Can't get device info: No such device # bluetoothctl Agent registered [bluetooth]# devices No default controller available HCI socket does not seem to be created. Got this in dmesg: [ 11.990128] Bluetooth: HCI device and connection manager initialized [ 11.990145] Bluetooth: HCI socket layer initialized [ 11.990164] Bluetooth: L2CAP socket layer initialized [ 11.990188] Bluetooth: SCO socket layer initialized [ 12.081220] Bluetooth: HCI UART driver ver 2.3 [ 12.081245] Bluetooth: HCI UART pro…

Hey guys, looks like there's no support for board serial number in latest images for Station M2. Serial number on rk356x is coming from otp memory, so: 1) there are no bindings for `otp` and `cpuinfo` devices in .dts, like here 2) there are no kernel driver to extract data from otp memory, like here I'm ready to contribute, but not sure what's the future plan for those.

All armbian images with 5.x kernel are not working for me. I found working variant of 5.x kernel here - https://github.com/qxhome/rk3568-kernel5.10-alldrivers but it have problems with firewall and docker Does anybody have other variants?