Allwinner sunxi

hello, there is no option to install in flash, Install/Update the bootloader on SPI Flash im using olimex a20 lime with emmc Armbian 23.8.1 Jammy with Linux 6.1.47-current-sunxi verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun7i-a20 rootdev=UUID=6a1af220-c7aa-449a-b709-c3eb897ae28a rootfstype=ext4 overlays=mmc2 pwm spi-add-cs1 spi-jedec-nor spi-spidev param_spinor_spi_bus=0 #param_spinor_spi_cs=1 param_spidev_spi_bus=2 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u im using like that but it dont boot if i remove sd lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS mmcblk0 179:0 0 …

Hello, I hope someone might help me on this. Is anyone here using the ENC28J60 Ethernet port on an Orange Pi Zero 2W or Orange Pi Zero 3? If so, can you please share the file .dts (or .dtbo) that is working for you? I've generated a .dtbo using the file in https://github.com/armbian/sunxi-DT-overlays/blob/master/examples/spi-enc28j60.dts, with: dtc -I dts -O dtb -o /boot/overlay-user/spi-enc28j60.dtbo spi-enc28j60.dts but still it doesn't work. It says "chip not found". I'm using the same cable pinout as in my Raspberry Pi Zero 2W and it works successfully, but not in the Orange Pi Zero 2W. Any idea?

For information purposes, that the 1.3-inch SH1106 OLED connected to I2C on OZPI v3 works very well OLED connected to PIN 3 of SDA and PIN 5 of SCK and in armbian-config in HARDWARE set to [*] i2c3-ph Using tools i2cdetect -y shows that the OLED is at address 0x3c All Python code with the adafruit library works fine

I am using orange pi pc plus after using armbian system, there is an infinite network with WLAN0 and WLAN1, but at present there is no law to use both networks at the same time and connect different SSIDs. Error: Connection activation failed: (7) Secrets were required, but not provided. pi@orangepipcplus:~$ cat /etc/os-release PRETTY_NAME="Armbian 24.5.0-trunk.512 jammy" NAME="Ubuntu" VERSION_ID="22.04" VERSION="22.04.4 LTS (Jammy Jellyfish)" VERSION_CODENAME=jammy ID=ubuntu ID_LIKE=debian HOME_URL="https://www.armbian.com" SUPPORT_URL="https://forum.armbian.com" BUG_REPORT_URL="https://www.armbian.com/bugs" PRIVACY_POLICY_URL="https://www.armbian.co…

I have question. OZPI v3 has support for hardware DS18B20 thermal sensor via w1-gpio ? In armbian-config when we got to the “system” section and select “Hardware” is not existing w1-gpio or OZPI v3 has not support for w1-gpio hardware ? Does not work because there is no device tree file (in the /boot/dtb/allwinner/) and we need to create it ??? like for OZPI v2 ?: 1. Create text file "sun50i-h616-w1-gpio.dts" /dts-v1/; / { compatible = "xunlong,orangepi-zero2\0allwinner,sun50i-h616"; fragment@0 { target = <0xffffffff>; …

Hi all, First post here. I have been running Armbian on my original Bananapi Pro for a long while now, and thought that it's time to upgrade from Bullseye to Bookworm finally. There were some complications with UsrMerge that I had to resolve manually (I think some boot files from the original Buster installation were both in /lib and /usr/lib), but apart from that the upgrade appears to have worked: All userspace stuff is on Bookworm. # lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Armbian 24.5.0-trunk.530 bookworm Release: 12 Codename: bookworm However, the kernel seems to be stuck on 5.15…

Hello! I have Orange Pi Zero 3 I got Armbian image from this link - https://github.com/armbian/community/releases/download/24.5.0-trunk.474/Armbian_community_24.5.0-trunk.474_Orangepizero3_bookworm_current_6.6.28_minimal.img.xz Of course I've made apt update and apt upgrade And now I'm tying to install zigbee2mqtt using this guide - https://www.zigbee2mqtt.io/guide/installation/01_linux.html So, I can't list USB devices root@orangepizero3:~# ls -l /dev/ttyACM0 ls: cannot access '/dev/ttyACM0': No such file or directory root@orangepizero3:~# ls -l /dev/serial/by-id ls: cannot access '/dev/serial/by-id': No such file or directory I have …

Hello! I have installed image Armbian_24.2.1_Orangepizero_jammy_current_6.6.20_minimal.img from https://www.armbian.com/orange-pi-zero/ Orange Pi Zero H2+ 256M There are only utils root@mobi:~# armbian armbian-add-overlay armbian-install armbianmonitor https://paste.armbian.com/ayoxebogog

Hi I'm using an Orange Pi PC Plus with a LoRa HAT (Semtech SX1278) connected via GPIO. The tool which uses this HAT connects directly to the SX1278 chip on the HAT, no protocoll like SPI is needed. I'm using it for several years on RaspberryPi's without problems. But with the latest ARMBIAN Image for the Orange Pi PC Plus Armbian_23.11.1_Orangepipcplus_bookworm_current_6.1.63.img.xz I have issues in this constellation. The tool can not contact the SX1278 via GPIO, said the tool developer. It seems like I have to activate the GPIO pins before. I've tried to find information about that, but without success. So I hope to find here more in…

Hi guys, its the first time im gonna post here so bear with me, i am a recent user of orange pi zero 3, one with 4GB RAM and i have been able to run the latest community release on it, things work besides audio thru hdmi, but i have noticed that the video encoding and decoding is not working, albeit 3d acceleration works thru panfrost and Mesa. I have been digging this topic and i wanted to share what i found and maybe validate if im right or perhaps i am not getting this well. 1. Video encoding and decoding in G31-MP2 is something separated from what Mesa and panfrost would do, so even if those work i cant get video acceleration with h.264 etc. …

@ag123, @c0rnelius, and anyone else that has interest in sound on these devices. I have been able to put together a patch that enables audio for H161/H618 devices. So far only audio on HDMI works. Analog audio is still generating an error on startup. The patches were taken from a git repository by warpme: https://github.com/warpme/minimyth2/tree/master/script/kernel/linux-6.6/files , and probably came from the Zunlong SDK. A lot of the code was written by Allwinner. @pixdrift generated a version of the patches for Armbian and I continued to work on them. I have a git repository if anyone would like to test, partic…

Hello community, I'm a Linux enthusiast and I hope I'm reporting in the right place. I have a communication with a device that is behind a VPN, when trying to communicate the system displays the following kernel error below. Can anyone help me? root@brmgbhzfw001-pri:~# ping 192.168.2.1 PING 192.168.2.1 (192.168.2.1): 56 data bytes Message from syslogd@brmgbhzfw001-pri at Apr 20 15:40:36 ... kernel:[ 1975.023502] Internal error: Oops: 5 [#1] SMP THUMB2 Message from syslogd@brmgbhzfw001-pri at Apr 20 15:40:36 ... kernel:[ 1975.439706] Process 1c15000.crypto- (pid: 68, stack limit = 0x3cf3c816) Message from syslogd@brmgbhzfw001-pri at Apr…

Dear All, I get frequent and random disconnection from orangepizero3 onboard wifi with armibian community (self-built) both trunk and 24.02 current kernel, 6.6.26 and 6.6.28 message is always [21738.338021] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share it [21848.116072] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share it [21915.426734] unisoc_wifi unisoc_wifi sta0: sprdwl_report_connection sm_state (5), status: (2)! [21915.426817] unisoc_wifi unisoc_wifi sta0: sprdwl_report_connection Vodafone-CSC failed status code:1! [21919.477424] sprdwl:sprdwl_fc_add_share_credit, 536, mode:1 closed, index:0, share …

I have a orange pi3 lts. I tried to install either minimal ether gnome version. Wireless is configured and working . I tried to execute command sudo systemctl enable ssh and reboot but sshd is down always and screen show always desktop orange PI without any network connection. I tried to use also u armbian-config but ssh is always down and network is down . Any attempts is not working . In addition thr desktop interface is the same in minimal and gnome version .... very strange

Hello! I have a Zero2 board with 1GB of RAM. I compiled a Debian 12 desktop image for Zero2 using Armbian and I want to play online videos through a web browser. Unfortunately, the results have been disappointing as the performance for 1080p videos is very slow. I tried using swap, but it didn't help. I also attempted to play 1080p videos using MPV and VLC. MPV can still play the videos, but it feels sluggish, and VLC gets stuck on the screen until the playback is finished. I would like to know how to configure Zero2 on Linux to achieve video acceleration. I'm new to this, so I would appreciate some guidance. Thank you!

Hi everyone, Recently I have installed armbian Bookworm on my orangepi pc and i noticed that the LEDs were not working. The system is booting with no issue and I have connected to wifi and did an initial software update and bootloader update and still the issue is persisting. So I clean installed jammy on the pi to check it again and still the led was not working. Please help me out on this issue, and if anything more is required please do let me know.

After upgrading from the official version with kernel 6.1 to the CSC version with kernel 6.6 I noticed an increase in CPU temperature of as much as 10 degrees. Is this normal? Honestly, seeing 52 degrees at idle worries me a bit

I disabled Armbian kernel upgrades to stay at Armbian 23.11.1 until Armbian 24 stabilizes. Yesterday I unfroze the kernel upgrades to upgrade to 24.2.1. I run: apt update apt upgrade apt dist-upgrade Apt update says All packages are up to date. shows nothing. What did I miss?

Hello, about a month ago I got MangoPi QM-Quad - quite nice board, but with small support. Hardware specification: https://mangopi.org/mqquad Review: https://bret.dk/initial-mangopi-mq-quad-comparison/ I needed a raspberry pi zero board with usb-c with both host and otg ports and external wifi antenna - so after some consideration I want with Mango-Pi QM-Quad. Sadly after some work with available distributions I finally give up with trying to compile / build everything I needed and moved to getting Armbian to run on the board. Thankfully board is almost identical with orangepi-zero2 - so modification with edge kernel only required m…

Good day everyone, I am running into some issue while trying to update packages on my Nano Pi Neo Plus 2, I am currently running Armbian 23.02.2 Buster with Linux 5.15.93-sunxi64 on the board. I am trying to update my packages with apt-update however the error I am receiving back is the following: E: The repository 'http://mirrors.dotsrc.org/armbian-apt buster Release' no longer has a Release file. N: Updating from such a repository can't be done securely, and is therefore disabled by default. N: See apt-secure(8) manpage for repository creation and user configuration details. Can someone help me out to fix it? Thanks in advance!

This started happening since accepting the kernel when I used apt to upgrade the BananaPi Pro sbc I've got. armbianmonitor report: https://paste.armbian.com/izuboducul @teknoid are you aware of this?

Armbian 6.6.16-sunxi64 (bookworm) on NanoPi NEO2 NanoHatOLED fails: - GPIO devices are missing; 2024-03-29 23:04:55 root@M-DNS:~# uname -a Linux M-DNS 6.6.16-current-sunxi64 #2 SMP Fri Feb 23 08:25:28 UTC 2024 aarch64 GNU/Linux Seems regression of earlier issue that had been solved: Would appreciate as GPIO will restored in kernel.

Just installed armbian on an Orange Pi Zero 3. Right of the bat, had it apt updated and tried to install armbian-config. The package is unavailable, though. me@orangepizero3:~$ apt search armbian-config Sorting... Done Full Text Search... Done me@orangepizero3:~$ apt policy armbian-config armbian-config: Installed: (none) Candidate: (none) Version table: me@orangepizero3:~$ cat /etc/apt/sources.list.d/armbian.list deb [signed-by=/usr/share/keyrings/armbian.gpg] http://beta.armbian.com bookworm main bookworm-utils bookworm-desktop Having checked the beta.armbian.com, I don't see the `main` pool. Mirrors do have it, though. Very odd!

I am trying to build an armbian image for a nanopi R1S-H3 this used to be possible in the past. Now when I build and select the extended board list the R1S-H5 is present but not the R1S-H3. Should I build using another H3 board, or is the R1S-H5 close enought o get it to boot.

Is this the right place to post this type of content? I have a board for Orange Pi. Since I'm usually using windows, it's very inconvenient to burn u-boot. I'll post it to github later if you guys are interested! （Machine translated, English not so good, don't know if the description is apt or not.）

Hello again... How can I activate the wifi network? I have a nanopi neo plus 2 with wifi, but armbian don't find it. Ifconfig and nmtui don't find the wireless connection. Thank you

Hello, I'm trying to connect a serial device on my nanopi neo plus2, but the gpio uart seems to be disable, please can you help me step by step? I found some things on forums but I understand nothing .... Thank you in advance

Hello Dear all, I dont really understand why netplan is renderer: NetworkManager I try to put wpa_supplicant.conf but does not work. I have add my profile in /etc/NetworkManager/system-connections/ and test to connect with armbian-config it work. But, I don't know how to make my system automatically connect to wifi this way? Many thanks in advance for help.

Hi! So the problem is when I configure wifi hotspot using hostapd, isc-dhcp-server, and ifupdown, I'm able to start the AP, connect to it, and ping. However, the moment any device connects to the AP the serial console gets spammed with this message around once a second: protocol 0000 is buggy, dev wlan0 This happens on the unofficial Armbian build (from the Armbian OrangePi Zero3 page), DietPi, and the official OrangePi Debian build. The wireless band doesn't matter. Kernel version: 6.1.31-sun50iw9. I tried to set up the AP with NetworkManager, but couldn't manage to connect to it. Probably DHCP issues that I couldn't resolve. I haven't …

As per the Subject, the I2C bus 0 is enabled and detected, but I don't see an addresses being returned when I try the i2cdetect -y 0 command. I have a single PCF 8574A connected with address 0x38. and have double checked the wiring. The PCF8574A did respond on the I2C bus on another SBC. Thanks John

Hello .. I have tested both current release 24.2.1 (jammy and bookworm) on OPiZero, and usb otg not working .. on both .. Kernel is 6.6.20-current-sunxi module g_serial is loaded ttyGS0 exist serial-getty@ttyGS0.service is runing dtc overlays are usbhost0 - 3 ..all looks good on opizero side ... but on "computer side" not.. nothing happened when usb cable is plugged in .. no ttyAMC0 device was created .. no new usb hardware can be found in system log ... ..nothing.. Buster version works well... (my old installation) any advice ..? or it is any "actual kern…

Hi I have installed the latest image for Orange Pi Zero v1 https://dl.armbian.com/orangepizero/archive/Armbian_24.2.1_Orangepizero_bookworm_current_6.6.20.img.xz link from https://www.armbian.com/orange-pi-zero/ After the first boot, I see that it is kernel 6.6.20 Welcome to Armbian 24.2.1 Bookworm with Linux 6.6.20-current-sunxi Linux version 6.6.20-current-sunxi (armbian@next) (arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #1 SMP Sat Mar 2 17:23:09 UTC 2024 and when I run apt update& apt upgrade apt list --upgradable Listing... Done armbian-fir…

After an "apt upgrade", the kernel was switched to "Linux 6.6.16-current-sunxi64" (Armbian 24.2.1 Jammy). On the WiFi side, no problem, but for Ethernet, it no longer seems to detect the link. So I downgraded to "Linux 6.1.77-legacy-sunxi64" with armbian-config. After this, the Ethernet works again. Do you have any idea where this could come from? And if this can be fixed in future versions?

Hi Folks, I have a NanoPi NEO Air with Armbian Bookworm. Previously I was running Armbian 23.11.1 Bookworm with Linux 6.1.63-current-sunxi, but after an apt upgrade I am now with Armbian 24.2.1 Bookworm with Linux 6.6.16-current-sunxi. With this latest upgrade I completely lost the USB console feature which for my application is a MUST. How can I fix it? Have a nice day, Mattia

Armbian 24.2 is broken on Orange PI PC2 (Debian Bookworm CLI) Latest stable community release: https://github.com/armbian/community/releases/download/24.5.0-trunk.123/Armbian_community_24.5.0-trunk.123_Orangepipc2_bookworm_current_6.6.20_minimal.img.xz With update 23.11 -> 24.2 the orange pi pc2 no longer starts. I tried a new sd installation and it too does not appear on the network. Right now I don't have a serial cable to check but it is possible that the network driver is missing or not working. SD, SBC and PSU are 100% working: a revert to 23.11.2 makes it work perfectly.

I've installed Armbian 23.11.1 Bookworm on a FriendlyElec ZeroPi. This version works flawlessly. A few days ago I updated to Armbian 24.2.1 and since then the ZeroPi crashes and hangs. Sometimes it happens after a few minutes, sometimes after a few hours. When it crashes I can't ssh to the device anymore (headless operation). Unbound, AdguardHome and cups aren't accessable, too. The last messages of the journal in an open cmdline window are: Mär 03 20:50:14 azp kernel: rcu: INFO: rcu_sched self-detected stall on CPU Mär 03 20:50:14 azp kernel: rcu: 2-....: (5249 ticks this GP) idle=16bc/1/0x40000002 softirq=20679/20679 fqs=2625 Mä…

We have a project based on FriendlArm's NanoPi Neo Air board. Currently the devices are running Armbian 18.04 LTS loaded from emmc. We are looking for a way to update the devices "offline" / with no user interaction. We can upload data to the devices via FTP and also can execute shell scripts. We can not easily access the on-board micro SD slot but have an external SD-Slot / USB-A Port with lots of free memory on each device. Any hints or explanations are very welcome!

Hi, I am having a problem getting the graphical login to work... What I run is an ubuntu jammy image with gnome, however when I boot with my tv connected via hdmi it seems to work at first but finally I end up with a screen just displaying the above error. armbianEnv.txt contains the line "disp_mode=1920x1080p60" (a mode my TV supports), yet when the device starts it uses the 4k mode - could this be part of the problem? So how could I get this working and how would I ensure that my device only uses fhd resolution, even though my tv can also do 4k? Many thanks!

Hello, sorry for the dumb questions incoming, thanks for your time. Lately I spent a lot of time searching for a working image to run Kodi with wifi/ethernet/bluetooh on this board. Does anybody managed to play videos on Kodi on this SBC ? If yes, what armbian image should I choose for this purpose ? Do I have to build the image myself ? Tested LibreElec for this but no wifi because the drivers are out-of-the-tree, not in mainline Kernel. Read about my problem in many posts but didn't find what I was searching for... Not even sure if this SBC can be used as a linux media player. Any tip/link/guide/wiki on how to successfully install kodi/har…

Hello everyone! I am trying to set up a CSI camera for my Orange Pi win plus (A64). The camera is GC2035 and I have already seen it not easy with latest versions. New versions of Armbian have not CSI support and do not have drivers gc2035 and vfe_v4l2. I found you can somehow compile the driver but honestly.....I do not understand how. I know the process of ./compile.sh but no idea how to use this https://github.com/avafinger/gc2035 It says is for H3, probably not for A64 right? Looking for the oldest version of Armbian I could use, I found out on the archive this one: Armbian_5.59_Orangepiwin_Ubuntu_xenial_default_..&g…

I updated my system to the newest kernel and lost all WiFi. What is the deal???

As the title says. I can not get PWM to work. I can type gpio mode 2 pwm and no error. But when I try to access it from Klipper (3D Printer Software and Firmware) it won't work. However if I use gpio 3, in software, gpio 4 turns on. Please help me out here. Thanks, Kevin

I'm trying to flash the armbian image onto my orange pi zero 3 but it doesn't boot, no red or green light, I've tried both images (jammy and bookworm) but no success, I'm using Balena Etcher to flash the images.

Hi, what are currently the options of controlling 433Mhz sender/receiver devices from an orange Pi zero 3? Currently the gpios are no longer exposed via sysfs but you could re-enable that feature by compiling a new kernel with the proper configuration. Then wiringpi would work again and you could use 433Utils. But what would be the options without compiling a new kernel? What 433Mhz library exists that uses the new way of controlling the gpios? I am a bit confused about the current state of affairs, please enlighten me...

Hi, I am having problems connecting my orange pi zero 3 to my TV via hdmi: No matter what I try the TV reports "no signal". Before I came to armbian I have tried the vendor-supplied debian and arch images and could not get hdmi output on any of them, so it might be that my micro-hdmi adapter is faulty or that the hdmi-port on the device itself is faulty, but over the weekend I cannot replace any hardware so I thought I try here to see if anyone has an idea on what to try. The image I am currently running is Armbian_community_24.5.0-trunk.58_Orangepizero3_jammy_current_6.6.17_gnome_desktop.img. When I log into the device I ca…

Hi all, I would like to use the PWM1 in order to drive a charge pump, but I am struggling to enable PWM using the DTB on Armbian v23.11. Anyone succeeded in configuring PWMs in H616? Thanks in advance!

When testing my most recent builds using the Armbian build framework I found that I was experiencing a constant load greater than 1.00. At first, I thought this is probably normal to have a load during the system boot but after waiting over 10 minutes I found that the load did not decrease. Firstly, I used HTOP but could not find a process that was heavy utilising the CPU with the relative CPU usage show as low. Next I tried using TOP which revealed a process called kworker: freezeable_power. Trying to search for the issue I did not find much until I came across this old forum post that described the same issues I was having: https://forum.armbian.com/topic/75…

# PROBLEM: Recent bananapi m1 images (and other A20 boards?) have no kernel headers, and armbian-config is not working so no hardware support. # SOLUTION: Armbian_23.02.2_Bananapi_jammy_current_5.15.93.img.xz Take this image and install the headers manually - or update to recent ones from here (not all work). NOTE: Armbian_23.02.2_Bananapi_jammy_current_5.15.93_minimal.img.xz While is the same build, cannot unfreeze kernel changes in armbian-config gui Flash SD and drop the 3 kernel packages in /root/ After first boot run $ apt upgrade && apt upgrade --fix-missing Unfreeze kernel with $ armbian-config -> sys…

Hello i use armbian on my orange pi and have a problem about the wifi connection. I have my orange pi near my 3D printer. When i plug it in, to boot the armbian it works great. But the orange pi will (SOMETIMES) not connect to my wlan. When i change the room and put it nearly my pc, it will connect without any problems... So i check the wifi quality: - near my pc i have a link quality 70/70 - near my 3d printer i have a link quality 64/70 and signal level: 46dBm is this to low for a easy connection?? thank you

I have a NanoPi Neo V1.4 running Armbian 23.8.1 bullseye with kernel nanopineo 6.1.63-current-sunxi. Now, that I got my micro-USB port working for a SD card holder, I want to programmatically backup my boot SD on a regular base to another SD. Yes, it works by a full dd-copy. but this is quite time consuming and I want to skip some directories while backup, which does not work with dd. The idea: Take a new SD (same model as source SD) Create a new partition table and a primary partition 1 with fully equal parameters as my source SD Format partition 1 with ext4 and mount to /mnt rsync all files (exclude some directories as e.g…

Hello, I have Orange Pi One Plus with the kernel 5.15.80 of Armbian 22.11.1 and work well. , but after upgrading to 23.8.1 kernel 6.1.47 the network interfaces stop working at all. Even I try the 23.05.1, 23.05.6 all have same error which because the kernel is 6.1.x. Currenly I limited the internet access without the the network. May I know how to fix it in the console or someone can help to generate the 23.11.1 image for fixed this error. Thanks The error message like as below in the console terminal. [ 9.899195] dwmac-sun8i 5020000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -19) The spec of …

Yesterday, I tried to use the digital IO in my opi zero3, with the Python GPIO package from https://opi-gpio.readthedocs.io/en/latest/ by Richard Hull It depends on having sysfs files in /sys/class/gpio/ My original opi zero has these files and it works, but my opi zero3 doesn’t have these files I learned that /sys/class/gpio is created if the linux kernel is configured with a specific option ON, as suggested in the documentation: https://github.com/rm-hull/OPi.GPIO https://linux-sunxi.org/GPIO Also, a developer has made a change on the opi.GPIO project to support opi zero3 https://github.com/rm-hull/OPi.GPIO…

Hi, I am new here so please apologize if I am asking already asked question, but I couldn't find the solution. I am trying to install docker on my orange pi zero 3 which is running Armbian (24.2.0-trunk.519) aarch64, kernel version 6.6.15-current-sunxi64. I have found this post, but I was not able to install docker because I found 2 problem that I don't know how to solve. 1. Installing docker using armbian-config does not work. I install armbian-config, run it as su/sudo, choose docker and install. The installer does something and after it's done it returns me to the same screen where I have chosen docker to be installed. So, no confirmation that I hav…

I used armbian-config to set up boot from EMMC. Then I run dd if=/dev/zero of=/dev/mmcblk0 bs=1024 count=2048 And re-partitioned my SD Card. Rebooting with or without SD Card not possible.

I'm powering my NanoPi Neo V1.4 1801 through the USB type A port beside the Ethernet RJ45. I'm using Armbian 23.11.1 bookworm with kernel Linux nanopineo 6.1.63-current-sunxi. Now I want to enable the Micro-USB port (usually used for powering) to act as an USB host so that I can plugin an USB-stick. I found very few instructions for e.g. Orange Pi. There the device tree needs to be changed for usb@1c19000 and usb0-vbus. Also in armbianEnv.txt the line param_usb0_mode=0 should be added. But none of the instructions work for my NanoPi Neo. In the schematics, a SY6280 is connected via GPIOL2/USB0-DRVVBUS to the H3 cpu. …

I've no problem using my Banana Pi with a wifi connection. But if I plug it on my router with a ethernet cable it crashs after a short time. Should I upload the output of armbianmonitor when ETH is plugged? Because it will take me a few tries, to do that.

Hello fellow Sunxi forum members, Some may know me from previous Armbian adventures, primarily Orange Pi Zero 3... but I have jumped brands for a change of scenery (but not SoC). When researching H61X based boards for the Zero 2 and Zero 3 development we were doing in another thread, I found the Sipeed LonganPi 3H, which is a relatively new board that took a while to find. My first impressions are that is really well made, and packs a lot in to the Raspberry Pi Zero style profile (although it also has a daughter board). It was shipped quickly in a nice quality hard plastic storage case and.. best of all.. it has two hardware buttons.. so I can rese…

Hello. For some reason, UART1 does not work for transmission, only for reception. The transmitter pin itself is definitely working, I checked by switching this pin to output mode, and then switching it to a high/low logical level, everything works properly, the level on the Pin changes. How I check the UART itself: I installed picocom, shorted the TX and RX pins, and I’m trying to see what I’m sending. For UART2 this method works as it should, but UART1 only works for reception. I realized this when I opened the TX and RX, and was able to receive incoming data sent through the USB-UART converter.

Hello, i get question for BananaPi M3 user: which img are u using ? on my M3 works only old Armbian_5.83. If i try a new img, reboot it all the time😩

Hi, I am building a voice assistant on OrangePiPc on latest Armbian 23.11.1 Bookworm \l root@orangepipc:/etc/alsa# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [CDC PCM Codec-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sun9ihdmi [sun9i-hdmi], device 0: SUN9I-HDMI PCM i2s-hifi-0 [SUN9I-HDMI PCM i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 For some reason when I plan an audio file using cvlc or play cli tools, about 1 first second of audio is skiped for some reason. I guess this time DAC is initialized. How I can solve this issue?

Is this the reason why I don't see my soc temperature and how I can I solve?

Hello dear comminuty, I have spent the last few days trying to get Hardware-Accelerated Video Decoding Encoding to work on the H618. I have tried everything but it does not work. ffmpeg -input_format mjpeg -video_size 1920x1080 -i /dev/video1 -c:v cedrus264 -f rtsp rtsp://localhost:$RTSP_PORT/$MTX_PATH my goal is to output a rtsp stream from a camera. But I get this ERROR: [cedrus264 @ 0xaaaae53e5170] VE Open error. Error initializing output stream 0:0 -- Error while opening encoder for output stream #0:0 - maybe incorrect parameters such as bit_rate, rate, width or height sudo ffmpeg -f v4l2 -video_size 1280x720 -i …

Hi there, I am trying to build a voice assistant using OrangePiPc. This is not orangepi zero, but I am posting it here, because there is no subthread for orangepipc. OrangePiPc has an embedded microphone, but for some reason it doesn't work. When I run arecord, I get an input/output error. Any ideas? Here is a board description: http://www.orangepi.org/orangepiwiki/index.php/Orange_Pi_PC arecord -l card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [CDC PCM Codec-0] Subdevices: 1/1 Subdevice #0: subdevice #0 root@orangepipc:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Cod…

Hello and Happy New Year my lovely Armbian friends! I am aware that this topic is a reoccurring one, having abused the search function beyond its functional capabilities I have found the following threads that deal with somekind of sleep and wake with separate pins for each function: how to wake up OPi3 gpio to inform of system shutdown I would like to know if it is possible to have 1 pin act as both sleep and wake depending on its voltage? - if so how could i modify one of those dts in the first link? I am new to dts so not sure how the pin mappings are assigned. for example, I have a DRV5053 hall effect sensor tha…

I have a problem flashing the oranges. I flash it with a 32G SD card with Linux with a network cable directly to the switch. After the process is finished, I turn off the orange and remove the card and turn it on again, but the orange LED (communication) on the network card stops working. This occurs in every 10 oranges flashed, 1 or two this type of error occurs. What is the solution?

Hi all! I may need some pointers. I'm using a 2.4" LCD at spi1 which works as /dev/fb0 on armbian bookworm (6.1.63) Meanwhile I've learned frambuffer is deprecated and to be replaced by drm., but ... - I could not find enough details to understand the drm architecture in general - there is a linux/drivers/gpu/drm/tiny/ili9341.c how is that used at all? - How to use drm in armbian? For my case any acceleration is not necessary (and likely not possible even if the H3 has Mali Hardware) but I want to avoid further changes if /fbX is really gone. btw. I want to add touch with shared SPI soon, work in progress. …

Tried installing Armbian_23.11.1_Nanopineoplus2_jammy_current_6.1.63.img and it is super slow during first boot process regardless of SD type. Localization craps out with "Failed to set time zone: Transport endpoint is not connected". I boot with wired Ethernet and when I get to a prompt I can ping outside locations. apt update produces "Hash Sum mismatch" Anyways, doing my part testing legacy boards, hahahaha

My Orange Pi 3 LTS with Armbian 23.11.1 Jammy with Linux 6.1.63-current-sunxi64 is showing high load, but low CPU. The SBC crashed overnight. When I run htop, the following lines show state D: root lscpu root /bin/bash /usr/lib/armbian/armbian-hardware-optimization start root grep -q \<ondemand\> /sys/devices/cpu/cpu0/cpufreq/scaling_available_governors load average: 4.00, 4.00, 4.00 System load: 100% CPU usage: less than 1% sar -u 5 Linux 6.1.63-current-sunxi64 (hostname) 12/31/2023 _aarch64_ (4 CPU) 03:41:54 …

Hello after reading and reading some more for a week, I have managed to boot the modified cubieboard2 /Einstein A20 board in GSOC to point I can run Armbian-Config and start a desktop. https://www.radioddity.com/blogs/all/xiegu-gsoc-teardown-open-source-project may or may not have access to ports internally if production board and metal can rf shielding-so wary of hosing uboot. I'm using Fat16 /dev/sda1 boot with original GSOC.dtb, I unfortunately have no access to original Xeigu BuildRoot on obsolete cubetech kernel. Armbian is on /dev/sda2 on same sd card I see that wifi and battery can be changed in human readable GSOC.dtb ,can this be…

The system I currently use: Armbian 23.11.1 jammy Linux kernel version: Linux orangepipc 6.1.63-current-sunxi #1 SMP Mon Nov 20 10:52:19 UTC 2023 armv7l armv7l armv7l GNU/Linux Currently I want to make this OTG USB work like the other three USB Ports. Do I need to recompile DTS?

Hi all, I'm using an OrangePi 3 LTS with Armbian 23.11.1 bookworm current 6.1.63 xfce installed on a microsd card. Unlike some previous version I tried, now the wifi works correctly. As for the bluetooth, it works... every other time. That is, on one boot it will load, in the subsequent one it will fail, and so forth consistently. I'm not an expert, so if you need some output from some program, please tell me which. By now I can say that when it doesn't work, the bt icon in the systray doesn't appear, however if I try ps aux | grep blue* I find that obexd and blueman-applet are running. And if I launch blueman-manager I get an error dialog sa…

Hi everyone, Very green here. Basically I setup 1 of my orange pi a few months back with "Armbian_23.02.3_Orangepizero2_jammy_legacy_4.9.318". I recently bought another pi and wanted to set it up with a newer version. I see bookworm is now the latest. I have tried both CLI and Minimal but whenever I flash those into my micro SD the orange pi never boots up. My router doesnt see the connection, so it cant hand off an IP. I thought maybe it was a bad mini SD or a bad pi. But when I flashed the old jammy image into the same SD, the pi immediately picked up the connection, my router gave it an IP and I was able to log in as a root to the pi. I re…

Hello! How to turn off Wi-Fi and Bluetooth devices to reduce power consumption? armbianmonitor -U -> result in attachment. Thank you. armbian-hardware-monitor.log

Hello! Board: Orange Pi 3 LTS SATA-USB3: Bus 002 Device 003: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS578 SATA 6Gb/s Speed after load: sudo dd if=/dev/sda of=/dev/null status=progress ... (5,8 GB, 5,4 GiB), 50 s, 115 MB/s Speed after spindown: sudo dd if=/dev/sda of=/dev/null status=progress ... (4,5 GB, 4,2 GiB), 71 s, 62,9 MB/s After reboot the speed is again 115 MB/s The drive does not respond to changes in Power Management settings. Help me solve the problem. Sometimes the disk cannot start after spindown. Thanks!

Hi forum members, when I try to install the headers via: "sudo apt-get install linux-headers-$(uname -r)" I gote these errors: Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-headers-5.19.93-sunxi E: Couldn't find any package by glob 'linux-headers-5.19.93-sunxi' E: Couldn't find any package by regex 'linux-headers-5.19.93-sunxi'

My orange Pi Zero 2W does not boot with all accessible images. Following error is displayed - [/ init]: getty is ttyl [/init]: RootDevice is "/dev/mtdblock4" , GPT_SUPPORT=1 [/ init]: Try to load Nor mount: mounting /dev/mtdbIock4 on /mnt failed: No such file or directory [/init]: Failed to mount /dev/mtdbIock4! / #_ Can any member provide me a path to fix this error and boot my Orange Pi Zero 2W?

Hello wonderful people! I am having trouble getting my SSD1351 1.5" RGB SPI OLED working with my NanoPi Neo v1.4 running armbian 23.11.1 with kernel 6.1.63.. Since the removal of fbtft_device from the linux kernel I have had a really hard time getting any screen to work with any of my SBC's (except RaspberryPi using the fbcp_ili9341 library) I have tried converting fbcp_ili9341 for use with the NanoPi but I keep getting "Failed to load VideoCore kernel Mailbox"... so I gave up on that lol.. Then I learned dtoverlay was a thing and after days of searching around I eventually found a .dts file for the SSD1351 here (https://github.com…

Normally when you have installed a XFCE-Desktop image for the Pinebook A64 you could set the display brigthness with the following pkexec command to a readable higher level - like I did in the past (possible brightness values are 1-10 - on startup this is only set to 2): pkexec /usr/sbin/xfpm-power-backlight-helper --set-brightness 8 read-out command for the current value: pkexec /usr/sbin/xfpm-power-backlight-helper --get-brightness but on standard CLI-install pkexec and xfpm-power-backlight-helper are missing, so to use this command-line (in /etc/rc.local) you have to install these 2 packages: sudo apt install xfce4-powe…

Hey everyone, I am attempting to update my Orange Pi Zero from Armbian 22.0.2.1 to the latest 23.11 version however I am running into the issue that I am stuck on how to perform this update, I have tried it using the sudo apt dist-upgrade command and tried regular sudo apt update and upgrade commands but everytime it says there are no new updates available (also no errors), when there is clearly a new version 23.11 available here: https://www.armbian.com/orange-pi-zero/ What am I doing wrong? Is it maybe because it says unsupported userspace?

I've installed Armbian 23.11.1 Bookworm on a FriendlyElec ZeroPi. On the cmdline the linux command who gives the following output: dgs pts/1 1011643795265722162 (172.20.10.14) Usually it should be (as on a Debian Bookworm distribution): dgs pts/0 2023-12-14 10:43 (172.20.10.14) Instead of showing date and time the Armbian who command outputs this long integer number. Why? Is this a bug or do I miss any configuration? PS: the locale settings is identical on both devices, date shows on both devices the correct time.

Hello, community. For a while now, I've been trying to configure the input and output of i2s0 without success. The closest I've come to a result was with the adau7002 configuration, but I'm experiencing synchronous noise, as if the issue were related to a CLK. Let me provide some details to see if anyone can guide me. I have a Banana Pi M2 with Armbian 23.11.1 Bookworm and Linux 6.1.13-current-sunxi. I have a pcm1807 connected to the input, configured with SPI, outputting i2s left justified in 24bit, and operating as a master. The pcm is connected to a 24.5MHz crystal. My goal is to configure the system to capture audio in a generic i2s format and then play it b…

Bookworm 6.1 kernel Cinnamon terminal is unusable. The terminal screen flickers and the written text blinks with the cursor blink. Occasionally the terminal goes black. I am using an ancient 1024x768 screen. Is this the root cause, or is the terminal broken in Cinnamon?

Hello, I'm new to working with Armbian and Linux in general, but I have a HiLetgo VK172 G-Mouse USB GPS/GLONASS USB GPS receiver connected to my Orange Pi PC. When I open it with MINICOM, I get a response, but it doesn't give me the coordinates: $GPGSA,A,1,,,,,,,,,,,,,99.99,99.99,99.99*30 $GPGSV,1,1,01,27,,,22*7D L,,,,,203410.00,V,N*4E $GPRMC,203411.00,V,,,,,,,031223,,,N*79 $GPVTG,,,,,,,,,N*30 $GPGGA,203411.00,,,,,0,00,99.99,,,,,,*63 ... But I want to open it for serial communication in /dev/ttyACM0. Thank you very much, and any help you can give me would be appreciated.

Hi, guys. I'm using the last Armbian Cubieboard image (Armbian_23.11.1_Cubieboard_bookworm_current_6.1.63.img.xz) on my "Gemei G9" Allwinner A10 tablet. But via serial/UART the boot process stuck forever in "Starting kernel ...". Any tips on how to get the kernel to start? Thanks in advance Here is my boot log: U-Boot SPL 2023.10-armbian (Oct 13 2023 - 22:19:41 +0000) DRAM: 1024 MiB CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 ns16550_serial serial@1c28000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19 U-Boot 2023.10-armbian (Oct 13 2023 - 22:19:41 +0000) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Cubietech…

Hello, I tied to activate SPI an a BananaPI M1 an Armbian VERSION=23.11.1 but didnt succeeded! I activated "spidev" at armbian-config and tried diferent configurations in "armbianEnv.tx. with: overlays=spi0 spi-spidev param_spidev_spi_bus=0 i get roland@bananapi:~$ dmesg | grep spi roland@bananapi:~$ lsmod | grep spi spidev 20480 0 roland@bananapi:~$ ls /dev/spidev* /dev/spidev0.0 roland@bananapi:~$ I installed "Rf24" library for an nrf24l01 module and tried "scanner" "gettingstarted" and my own c++ file. Al long as I define a wrong "CE" pin, I get response from the nrf24I01 modul. Mostly I get some senseless info, but …

Hello! I am on the forum to ask you some questions that I am not able to find the answers to. I bought a 3D printer kit on Aliexpress.com including an Orange pi 3 LTS board. On the card there is an operating system installed and several applications for the printer. The first problem is that: I would like to activate WIFI on the card. I tried to do this via 2 different ways. The first is with the following command sudo orangepi-config. I go to the network/wifi menu. I chose my WIFI network. I enter the network key and I receive the following error code: Could not activate connection: Activation failed: IP configuration could not be reserved (not available addres…

Hi, in an attempt to add new information and correct conflicting information over at the bottom of https://linux-sunxi.org/SID_Register_Guide#Currently_known_SID.27s it would be great if as many owner of Allwinner boards could execute most recent sbc-bench version and post/share the result link here (ix.io/sprunge.us) https://github.com/ThomasKaiser/sbc-bench#execution The new sbc-bench version always lists the SID identifier next to the SoC so that it reads as follows for example: SoC guess: Allwinner H6 (SID: 82c00007) Especially boards with 64-bit SoCs like H618, H616, H6, H5, A64 but also R40/V40 and exotic varia…

Apt lists Armbian 23.8.3 as upgradable but refuses to upgrade. According to apt-cache the base files for 23.8.3 have not been updated for Orangepi3-lts. Is this the case or do I have a local problem with my install? --------------- # apt-cache policy base-files base-files: Installed: 23.8.1-bullseye Candidate: 23.8.1-bullseye Version table: *** 23.8.1-bullseye 500 500 http://apt.armbian.com bullseye/main arm64 Packages 100 /var/lib/dpkg/status 11.1+deb11u8 500 500 http://deb.debian.org/debian bullseye/main arm64 Packages

Hello -- bringing in conversation from https://github.com/armbian/build/pull/5726#issuecomment-1817668480 as requested. @viraniac -- I've attached the dmesg output from a fresh flash of the quadra SD image -- which is just armbian checked out at `90c05ba` with this patch applied: https://www.inovato.net/build/quadra.patch . Build instructions from the founder are at https://forum.inovato.com/post/building-armbian-from-source-12449428?pid=1333459893 Curiously the dmesg output almost looks truncated to me -- doesn't start with `Booting Linux on physical`, and I see a few xradio message but no results for 819. I've rebooted and get similar output wit…

armbianmonitor -u hastebin - yadagozohu (armbian.com) Using https://redirect.armbian.com/region/NA/orangepipc/Jammy_current image Attached is the output from the serial console for uboot etc. The console is using about half the vertical resolution, and a little under half the horizontal resolution of the HDMI monitor. In contrast, the orangepi.org built image is using the full resolution. Image: Orange Pi PC 2.0.8 based on Debian Buster Kernel: root@orangepipc:~# uname -a Linux orangepipc 5.4.65-sunxi #2.0.8 SMP Mon Oct 26 10:20:38 CST 2020 armv7l GNU/Linux In Armbian, I've tried using …

Hello, I'm using a BPI M2 Zero (with H3 Chip) to control two relays on CON2-P05 / PA11 and CON2-P03 / PA12. During the boot process there is a high level present at the pins, which is driving the relays. Is there a way to create a DTB overlay to drive the pins to a low level during boot. My userspace application uses libgpiod to control the pins. I'm familiar with compiling and activating overlays, i would just need help to write the correct .dts file. Thank you very much in advance

First time working with usb_f_uac1. Running buster image. I have a configfs setup that hosts are able to enumerate but the attributes for capture (c_chmask, c_ssize, c_srate) and playback (p_chmask, p_ssize, p_srate) seem to be switched. i.e. c_chmask = 0x3f shows as a 6-channel capture endpoint on both Windows (ksstudio) and macOS (system information) hosts. Is there something I’m misunderstanding here? Is there something I’m not doing correctly?

hi guys, using Armbian 23.02.2 Buster with Linux 5.15.93-sunxi on a NanoPi Neo Core LTS. I configured cron to do a daily reboot at 00:30. Every 10-20 days the system is becoming unresponsive unless I do a power cycle. Where should I begin to investigate this issue? Thank you

diagnostics listing of Orange Pi Zero 2W http://ix.io/4Lwr Not sure if this helps..but the stock build is lacking...plus I am getting 1.0 cpu usage at idle Orange Pi 1.0.0 user-built System too busy for benchmarking: 16:33:21 up 25 min, 3 users, load average: 1.15, 1.03, 0.92 System too busy for benchmarking: 16:33:26 up 25 min, 3 users, load average: 1.14, 1.03, 0.92 System too busy for benchmarking: 16:33:31 up 25 min, 3 users, load average: 1.13, 1.03, 0.93 System too busy for benchmarking: 16:33:36 up 25 min, 3 users, load average: 1.12, 1.03, 0.93 System too busy for benchmarking: 16:33:41 up 25 min, 3 users, load average: 1.11, 1.03, 0…

Greetings! I have acquired for cheap this old board. It runs an old Android (4.x) and I'd like to run Armbian on it, but lack the knowledge to do that by myself. The idea would be to start with booting a Linux a SD image, then attempt to install it on the onboard flash in place of Android. The board is not for sale anymore and the manufacturer removed any mention of it from their site, however Archive.org has a copy along with related files, manuals, firmware etc: https://web.archive.org/web/20140701064007/http://www.giadatech.com/index.php?act=pShow&id=36 The board presents itself when not in USB host mode as "SoftwinerEvb" which appears to be …

Hello, I just started to use my old BananaPi M1 (Armbian 23.8 Bookworm) to check sensor values by onewire and i2c. At last there was no problem with onewire But I cannot get I2c to work. /boot/armbianEnv.txt overlay_prefix=sun7i-a20 overlays=i2c2 w1-gpio param_w1_pin=PI3 For onewire I had to define "param_w1_pin=PI3" even if my onewire sensor is connected to GPIO7. for I2C I checked "lsmod | grep i2c" but couldnt find anything. So ieven if it is not correctly activated, I could run "i2cdetect -y 2" and could find my sensor at 0x76 but couldnt communicate with it. I think I need to load "i2c-bcm2708 i2c-dev". Ho…

I recently picked up an Orange Pi Zero 3 and have been trying to figure out how to get the i2c pins working on the GPIO. The pinout shows pins 2 and 3 (229 and 228 according to the orange pi version of wiringPi) being used to i2c-3. The downloadable images seem to be hodge-podge with the orange-pi-os version based on arch linux. But their instructions appears to be based on earlier orange pi models that had an Orange Pi OS based on armbian which included a 'orangepi-config' command similar to raspi-config. There is no orangepi-config in the arch-based Opi-OS. A third party image from leeboby includes a current buster version of Raspbian but while it contains raspi-co…

Hi, I could enable "spidev" support by armbian-config -> system -> hardware (enable spidev) . Everything worked fine. However, the original spidev module supports messages only up to 4096 bytes. I compiled a new version of custom spidev.ko with the 32,768 buffer size. Then, converted it to spidev.ko.xz ( xz -v spidev.ko) and replaced the original file under /lib/modules/5.15.85-sunxi/kernel/drivers/spi/spidev.ko.xz The new module works fine when I install it manually: insmod /lib/modules/5.15.85-sunxi/kernel/drivers/spi/spidev.ko.xz However, after the reboot the original 4096-byte version of "spidev" module is loaded magically.…

Hello, I installed 2022-09-27-Armbian_22.11.0-trunk_jammy_edge_lubuntu_5.19.6-qt5-swap-bpi-p2z-10804MB.img on my Banana Pi Zero and it works great! I run sudo apt update , sudo apt upgrade ... Hours later, time to reboot. The board reboots and crashes.. See pic. Hmmm can't attach pics for some reason. First error I see on the screen says Failed to load '/boot/dtb/sun8i-h2-plus-bananapi-p2-zero.dtb libfdt fdt_check_header(): FDT_ERR_BADMAGIC No FDT memory address configured. Please configure the FDT address via "fdt addr <address>" command. Aborting! Then a bunch of other errors …

First, I have installed latest Armbian 23.8 Bookworm CLI, boot works fine, I can login Then, I have installed wireguard. As a dependency, wireguard install linux-image-6.1.0-12-rt-armmp After reboot device is unavailable in network (orange LAN LED blinking while green does not, I assume ethternet broken with this kernel)