Rockchip

Hello All, I have bought banana PI m5 pro SBC, but there is no wiringPI developed for this edition and armbian-config doesnt show UART,i2c enabling method may I know how to develop wiring pi for this edition and how to enable i2c and uart manually

Filed this as armbian/build#10551 and was (reasonably) pointed here instead, since it's a kernel-code observation rather than a build-framework bug. Posting for the record — this is a question about the code, not a bug report. Where: drivers/gpu/drm/rockchip/rockchip_drm_vop2.c — identical across Rockchip BSP 6.1, ubuntu-rockchip, and Armbian rk35xx-vendor-6.1 (carried unpatched). rk3568_vop2_cfg_done() waits for the layer-select latch to take effect when it changes: old_layer_sel_val = vop2_readl(vop2, layer_sel_offset); cfg_layer_sel_val = vop2->regsbak[layer_sel_offset >> 2]; ... vop2_writel(vop2, 0, val); /* Make sure the layer sel is take…

When using my (intel) laptop I get when I check my nvme (as root): # lspci -vvvs 01:00|grep -E "ASPM|L1" DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited LnkCap: Port #0, Speed 16GT/s, Width x4, ASPM L1, Exit Latency L1 <8us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ Capabilities: [900 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+ L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- L1SubCtl2: T_PwrOn=500us With the 6.1-…

I tried the latest 6.8 kernel edge on my Rock 5A and noticed the CSI camera interface doesnt exist. Is there any plan or time schedule to fix that? I saw it's marked "TODO" on https://gitlab.collabora.com/hardware-enablement/rockchip-3588/notes-for-rockchip-3588/-/blob/main/mainline-status.md . So in 6.9 perhaps? (A LOT of other stuff works remarkably well though, great work!)

I'm trying to get wifi working with the new wifi chip on the official image 23.5 but it seems to be missing the dtb for the Orange Pi 5b. Does anyone mind posting that file? I did follow the steps to extract that file from an official image but I can't trace the source anymore. Also any update on the availability of the 23.5 images in the apt? I just switched my release to nightly but it still shows 23.02 Thanks Erik

I am trying to get a RPi camera (imx219) working on a RockPI 4C. I have been piecing together DTS files from various places trying to make sense of it, and I noticed that the rkisp kernel module isn't compiled on the Rockchip64 kernels. Is there a reason for this or am I missing something? Looking at the kernel menuconfig, only one of its dependencies isn't compiled: `V4L_PLATFORM_DRIVERS=n`.

Hello All, Preface: First time posting, I am not an experienced software developer but have designed a working SBC around the RV1126. I have had some success recently getting video out of an IMX258 camera connected to the RV1126 but I am experiencing a strange issue where the camera feed has a green hue. (see attached picture). I have tried to change variables within the kernel - IMX258.c and many other places to change the auto white balance with no success but have recently come across this thread which may provide better results: https://forum.pine64.org/showthread.php?tid=17067 I do not have the RKISP2_tuner.exe in the camera_engine_rkaiq …

Hi, I've installed Armbian Jammy on a Rock 3A. It seemed to run very stable, (much more so than the Rock 64) however the first IMPORTENT issue I've found is that the system appears to freeze when Chromium is launched as well as VSCodium. That is to say I loose mouse and keyboard control, so I can't tell what else may be effected. There may be others, still checking. Any help appreciated.

I have a ROCK 3A that reaches Maskrom/recovery but will not boot any Radxa or Armbian SD image and produces no useful UART output. UART is configured per Radxa docs at 1500000 8N1 on the debug header, and the exact same adapter/host/settings work on another ROCK 3A. There is no eMMC and no NVMe installed. I also tried resetting/loading SPI via Maskrom using rkdeveloptool db rk356x_spl_loader_ddr1056_v1.12.109_no_check_todly.bin, then loading Radxa’s rock-3a-spi-image-gef9f6b1caad.img. Radxa’s ROCK 3A loader directory contains the matching SPI artifacts, including rock-3a-spi-image-gef9f6b1caad.img, rock-3a-idbloader-gef9f6b1caad.img, and rock-3a-u-boot-gef9f6b1caad.itb, a…

[22787.457010] Internal error: Oops: 0000000086000004 [#1] PREEMPT SMP [22787.457594] Modules linked in: xt_nat xt_tcpudp veth xt_conntrack nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlinks [22787.465404] CPU: 1 PID: 609416 Comm: kworker/u8:5 Not tainted 6.1.11-rk35xx #23.02.2 [22787.466103] Hardware name: Radxa ROCK3 Model A (DT) [22787.466552] Workqueue: ext4-rsv-conversion ext4_end_io_rsv_work [22787.467107] pstate: 804000c9 (Nzcv daIF +PAN -UAO -TCO -DIT -S…

Hey everyone, was wondering if there was a readily available rock3b armbian image. I have found that the rock3a/3b are quite similar baring an extra ethernet port. So was hoping to see if I could take the rock3a image and make some simple modifications but don't know how. Any help would be appreciated thanks.

Built latest image for a Rock 3c based device and am having an issue with ethernet connectivity. Boots fine. Wifi works well and it seems functional other than Eth connectivity. My old DTB (from 4.19) will not boot , using a rock3c DTB instead to get a 90% functional device Showing the following for ethernet dmesg | grep eth [ 0.000000] psci: probing for conduit method from DT. [ 3.199039] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 3.199576] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 3.199601] rk_gmac-dwmac fe010000.ethernet: TX delay(0x30). [ 3.199614] rk_gmac-dwmac fe010000.ethernet: RX delay(0x10). [ …

Hello, I ran sudo apt update / suodo apt upgrade on my Rock 3C this morning. I did notice that the kernel was upgraded but rebooted. It transpires that the kernel was upgraded to a completely new version (6.12.9) from 6.6.63 (or 62 I believe).

Hello everyone, I am new to this so please forgive my eventual mistake. I have a Rock 4 SE with Armbian Linux 6.12.13-current-rockchip64 (bookworm) for Rockpi 4B (because there is not a special version for SE it re-commanded to use 4B). And I try to use the CSI port to connect a Camera Raspberry Pi V2.1. And I does not work, I have tried to add different value to the overlay in /boot/armbianEnv.txt like overlays=rockchip-csi csi or imx219 with a reboot each time, but it doesn't seem to work. Looking around, it seems like there is a lot of issue with csi camera and rock 4 with armbian (and sometime other os). But none seems to have…

Hi people! I'm trying to use Armbian 23.8.1 CLI with the Rock 4 SE board without success. I write the eMMC in the classic way: xzcat Armbian_23.8.1_Rockpi-4b_bookworm_current_6.1.50.img.xz | sudo dd of=/dev/sdb bs=4M status=progress; sync but nothing seems to happens, i have only the green led on, the blue led is not blinking and the display says "no hdmi signal". No problems with the image from radxa. Do you have any idea what's going wrong?

Hi, i just received my Rock 4 Se and a 32GB eMMC module today, and i'm currently not sure if the Image is incompatible, or if my storage modules are broken. I tried emmc standalone and SD for boot with nvme (from an dell notebook) for rootfs When i use the emmc, the filesystem goes into read only as soon as i do some apt upgrade. On reboot i often end up in initramfs nd have to fsck. I could gether some dmesg output: After this trace i get a lot of I/O Errors: Im not sure if this is an os or an emmc module issue. Any guess whats going wrong here? after that i coppied the current…

tried several armbian images with kernel 5.15.76, no success! even tried to disable SPI flash, although radxa says "no SPI Flash on the board" in contrast to the 4B version official 4.4 radxa image is booting: rockpi-4b-debian-bullseye-xfce4-arm64-20221109-1447-gpt.img can someone send me armbian bullseye image with older kernel?

I have a rock 4b+ and I used it as an android box for a while. Then today I tried to flash it with latest armbian image (23.8.1) and it does not boot in microSD or when I flash it through USB OTG. I have erased the SPI flash completely and install the correct spi_loader. It also boots properly with Radxa debian image. Initially I though this is a boot issue, but after checking with a serial cable, it turns out this is a HDMI issue.. After I finish the usual procedure to setup password etc... I got this: Now starting desktop environment... root@rockpi-4b:~# [ 633.211385] hdmi-audio-codec hdmi-audio-codec.5.auto: Only one simultaneous stream su…

I'm new to SBC and tinkering with Rock 4C+ (plus) board and appreciate some support and guidance for blueooth setup. Installed Armbian 23.11.1 Bookworm CLI build. Enabled BT package from Armbian config utility as well tried installing bluez package from CLI using apt command afterwards. Started bluetooth service but seems not working. Command sequence I used: sudo apt install bluez sudo service bluetooth start sudo service bluetooth status (output says Loaded & Active). 'hcitool scan' command however returns message "Device is not available: No such device". When I installed Radxa's official Debian 11 des…

Hi I have install the armbian system into my SSD device. But how can i manage to get it to start from that? The system dont seems to want to boot only from that SSD. I need to have the Micro SD inserted into the card reader for it to be able to boot. After that it seems to first boot up whit the SD card after that switch over to the SSD. How is that happening? NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 465.8G 0 disk └─sda1 8:1 0 461.1G 0 part /var/log.hdd / mmcblk0 179:0 0 29.8G 0 disk └─mmcblk0p1 179:1 0 29.5G 0 part zram0 2…

I have a project developed on Rock 4C+ v1.2 board. Now there is only v1.41 board available and Armbian is not booting on it at all, no matter it's compiled locally, or it's downloaded from the official sources. UART debug is producing unreadable sequence. So far, what I’ve tried: - I’ve built Armbian with the latest changes armbian build repo - hasn't helped - I’ve used rk3399-rock-4c-plus.dtb file instead of rk3399-rock-pi-4c-plus.dtb, dunno why there are two, but somewhere on the forum I read that this one without “pi” is the right one - hasn't helped - official Armbian images - not booting - Ubuntu and Debian - both booting fin…

PI-co ITX form factor(2.5 inch, 100 x 72mm) RK3588 powered, 8nm manufacturing process Quad A76 2.4Ghz + Quad A55 1.8Ghz Mali G610MC4 GPU(up to 5 channel 4K UI) 6T NPU 8K 10bit decoder, 8K encoder Support WiFi 6E and BT5.2 Support PCIe 3.0 x4 NVMe SSD Triple display support(with HDR) Two HDMI 2.1up to 8K@60FPS One USB C with DP up to 8K@30FPS HDMI in support up to 4K@60FPS 2.5G Ethernet with PoE support Offer 4GB/8GB/16GB(LPDDR4x) ram options

I was getting kernel panics and discovered that my 32 GB Rock 5B Blue Edition just crashes when I try to malloc 8-9 gigabtes of memory. Is there a way to specify that this board has 32 GB ram? 5.10 works fine.

As per the title: Using the image Armbian_22.11.2_Rock-5b_bullseye_legacy_5.10.110 Formatting an nvme ssd partition as BTRFS and running the armbian-install utility, install using SPI to boot, targeting ththe btrfs partition, and selecting BTRFS in the prompt results in a failure to boot. Reformatting that same partition as EXT4 and rerunning armbian-install (and making no changes to the data loaded to /de/mtdblock0) targeting the EXT4 partition, and the device boots using the SPI loader.

Hello, When I try to build any image for 5B with the Edge kernel and Ubuntu, it will not boot. No matter if desktop or server, both green and blue LEDs are permanently on, and the board doesnt start. If I choose Mainline or Midline kernel, it works. I used the official build enviroment, host is Ubuntu22, all updated & upgraded https://github.com/armbian/build

Hi, I've installed Armbian 23.02 Jammy Gnome (Release date: Feb 18, 2023). Mostly it works well, including the instructions on the download page to enable 3D acceleration. However, my video is output to a TV through HDMI, and there is no audio. There are four "Analog Output - Built In Audio" options in the sound settings, I have tried all four and none of them make any sound. I have also tried to change all five options in the configuration tab of PulseAudio volume control. All are labelled "Built-in Audio" and there are no options in any of them other than "Stereo Output", "Stereo Input", "Stereo Output + Stereo Input" and "Off". I don't know if this is related, but…

I wanted to upgrade from the previous release to the current one. apt update & apt upgrade and reboot worked fine but I noticed it was still on the 5.10 kernel so I used the config utility to switch to 6.7 and now I can't get a display output on HDMI 1 or 2 and its not getting an IP address either. I'm booting from M.2 NVME. Is there any way to fix my setup?

Hello everyone, Hello everyone, I have installed Armbian Bookworm 23.11.1 (kernel 5.10.110). The fan control does not work. The fan only runs at level 1. None of the many patches I tried worked. The last one tried was this: https://forum.radxa.com/t/guide-on-how-to-customize-you-pwm-fan-curve/17442 I can adjust the fan manually, but the automatic doesn't work. The "policy" file (/sys/class/thermal/thermal_zone0/policy) cannot be permanently changed to "step wise" (logged in as root). After restarting it is back to "user_space"... The access rights are: -rw-r--r--1 root root 4096 Feb 11 02:42 policy …

Hello everyone, I have installed Armbian Bookworm 23.11.1 (kernel 5.10.110). The fan control does not work. The fan only runs at level 1. None of the many patches I tried worked. The last one tried was this: https://forum.radxa.com/t/guide-on-how-to-customize-you-pwm-fan-curve/17442 I can adjust the fan manually, but the automatic doesn't work. The "policy" file (/sys/class/thermal/thermal_zone0/policy) cannot be permanently changed to "step wise" (logged in as root). After restarting it is back to "user_space"... The access rights are: -rw-r--r--1 root root 4096 Feb 1102:42 policy Owner: = Root Root…

Hi, Using the image Armbian_23.5.0-trunk.181_Rock-5b_lunar_edge_6.3.1.img I get this error at boot: Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. done. Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! UUID=6a70cc68-5120-4343-887c-ca90fd2188f9 does not exist. Dropping to a shell! The SD card is wo…

Hi all, https://paste.armbian.com/koqimivaro vendor kernel boots, detects ethernet, wifi & nvme (booting from SD card) and seem to be working well. Also attached are the UART gathered first boot/install logs. I think the SBC accidentally skipped over the root password by resting on the enter key 😁 uart-logs.txt

I have a rock 5c headless server running debian minimal with kernel 6.12.20. It runs fine for my use case, but the fan runs at full speed by default. I can manually set different fan speeds in /sys/devices/platform/pwm-fan/hwmon/hwmon2/pwm1 I have selected 'fanctrl' in armbian-config, but this does not reduce the default speed of the fan. I noticed that there are some recent patches published here and here, I assume these patches are there to deal with the fan control deficiency? Could these patches either a) be applied to the rock 5c dts file that comes with the armbian image or b) perhaps it is better to create a user defined ove…

Hi, I've burn "Armbian Stretch desktop legacy kernel 4.4.y" on sd card on use nand-sata-install on emmc but when I remove sd card it's no boot. I read on Pine forum we must put a jumper on "emmc pin" then remove 3/4s after power on. So I've try but no success. I can see emmc when I boot from sd card but no more.

Hi all, a new RK3399 board appeared, it is called RockPi4 I have two of these beasts here already, and they works nicely - I like the small details about it (nice eMMC fixture, all heat plates on the bottom side for simple cooling, and an M.2 PICe slot for my second network card Do you see any chance to get Armbian working on that beast, and if so, what can *I* do (with my limited experience in kernel programming)? Debian is working on it already, in case you need more specific information please let me know. Any help is appreciated. So far, Michael

The following image boots fine from microSD card on my RockPI4a (2GByte): https://dl.radxa.com/rockpi/images/third-party/Armbian_5.67_Rockpi4b_Debian_stretch_default_4.4.154_desktop_20181210-gpt.img.gz Unfortunately, that images' kernel does not seem to include an AHCI driver, so it does not find the 5 SATA port miniPCIe controller. i am using. That controller is working (mostly) fine with the Radxa provided 4.4.100 debian kernel though. So, i tried to install the following current images: https://dl.armbian.com/rockpi-4a/Buster_current https://dl.armbian.com/rockpi-4a/archive/Armbian_19.11.5_Rockpi-4a_buster_current_5.…

Hi Distro Debian Buster, Linux rockpi-4b 5.10.21-rockchip64 #21.02.3 SMP PREEMPT Mon Mar 8 01:05:08 UTC 2021 aarch64 GNU/Linux I trying run HDMI-CSI bridge (auvidea B101) with board RK3399. Driver is loaded but dmesg not see any communications. root@rockpi-4b:/home/stream# lsmod |grep tc tc358743 40960 0 v4l2_dv_timings 36864 1 tc358743 v4l2_fwnode 28672 1 tc358743 videodev 299008 8 rockchip_vdec,v4l2_fwnode,videobuf2_v4l2,hantro_vpu,rockchip_rga,videobuf2_common,tc358743,v4l2_mem2mem mc 61440 7 rockchip_vdec,videodev,videobuf2_v4l2,hantro_vpu,videobuf2_common,tc358743,v4l2_m…

pi@rockpi-4b:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: rockchipes8316c [rockchip,es8316-codec], device 0: ff880000.i2s-ES8316 HiFi ES8316 HiFi-0 [ff880000.i2s-ES8316 HiFi ES8316 HiFi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: HDMICODEC [HDMI-CODEC], device 0: ff8a0000.i2s-i2s-hifi i2s-hifi-0 [ff8a0000.i2s-i2s-hifi i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 pi@rockpi-4b:~$ How is it possible to turn on the sound on HDMI? There is sound on the 3.5mm socket. But when I click on the speaker in the top right, then Volume Control. Only "Analog Output" can be selected as output devices.

Hi, i use a Rock Pi 4b with a external USB3 Seagate 4TB HDD on USB3 Port on RockPi 4B. Der HardDisk ist ext4 formatet und mounted via fstab The maximum troughput over Samba Share is around 11 Mbit The same USB HDD on a Odroid with same samba settings has an troughput over 100 MBit Any Ideas ? Thanks Ingo

Hi, An old problem, since I got the board which is 4C. Not a + - or whatever but the plain C. Symptoms: 1. HDMI worked randomly, maybe every 10th...15th boot lead to a working system, or rather to a visible HDMI-connection. But now switching on-off does not help at all. 2. Quite often one can get the board booting to the point where it asks for the password, and after clicking ok, it switches the screen off, and won't return. So the telly says that "no signal". 3. When switching on the board the tv set sees that there's someone on the hdmi port, and shows the booting sequence, and finally goes to Armbian's graphical mode asking for t…

After installing Arbian on Rock pi 4 c the sound on the Jack does not work because the sound card driver is. 8316 is not supported The sound goes out anyway on the HDMI of my television Would there be a solution

Please, I need an img of Armbian compatible with the following: RK3399T and with HDMI. I have tried all versions of Armbian and they do not work. Some do, but the problem is that it does not display an image. I believe it could be the HDMI. The most preferable versions for me are Armbian Noble or Bookworm. The problem also occurs during updates. After updating, the wireless does not work. If there is a version with this fixed, I would be grateful if someone could post a version for me, as up-to-date as possible. My Radxa is a Rock Pi 4Plus v1.73. With a 256GB microSD, I need an img of Armbian that is compatible with wireless and HDMI. If anyone can send me the link, I wou…

System logs: http://ix.io/4bd2 I have been using Armbian OS with Rock Pi 4B. The problem with Rock Pi 4B is that it doesn't have a power-on/off button. So, for closed systems with no keyboard/UI, there is no way to shutdown/start the system properly. Only option is to disconnect the power cable, which has corrupted my OS few times(by the way didn't happen on Debian). I implemented shutdown function through MRAA library and by attaching a button to 40-pin GPIO header. But with this approach, system can go to sleep, but cannot wake-up through button because my software is not running. As I have understood, the best approach to have a proper button f…

How do I use a camera that I have connected through the connector on the board? I tried running armbian-config but did not find anything about a camera.

Hello, ttyS2 is used for console output by default. In my application I need this port for custom communication. Is there any way to disable the console on it? Thanks

Hello, is it possible to install WiringPi on Rock Pi 4? I tried to install WiringX using the instructions on https://github.com/wiringX/wiringX , but after installing it the command "gpio" is not present. Any hint on how to get "gpio" command on Rock Pi 4? Thanks

tried several Images Bionic, Buster Desktop and several Kernels 4.4 - 5.6... Can't get to work HDMI Output (black screen on 4.4) and Bluetooth (firmware issue missing file) on same kernel version. Did someone has a working build for Rock Pi 4 board v1.4? Thanks

Any guesses whats wrong? The bootup stucks at [ 311.991668] random: crng init done for such a long time with 5.4.49... That happend on two different ROCK PI 4B 4GB v1.3 with SPI and NVME SSD boot without SD/eMMC. (fdtfile=rockchip/rk3399-rock-pi-4.dtb). It is only happening if I disconnect power and boot up. It seems working fine if I just restart the board. No problems with 4.4.213 Kernel (fdtfile=rockchip/rk3399-rockpi4b.dtb). It was also working fine with an older version of 5.4.xxx... channel 0 CS = 0 MR0=0x98 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR…

The binaries supplied with the ArmBian release for the Rock Pi 4 work great. However, when I try to build my own from Mainline sources, I see lots of booting issues. Do you use Rockchip provided binaries, or are they built from scratch? Any help would be gratefully received.

I loaded both the Raxda Debian OS and the Armbian OS on the Rock Pi 4A+ (4GB RAM / 32GB eMMC) integrated eMMC chip and both boot fine. I then ran the Phoronix pts/scikit-learn benchmark and got a big discrepancy in performance: https://openbenchmarking.org/result/2112285-NE-2112281NE08 The Raxda Debian OS (noted as rockpi4a+raxdadebian in the benchmark) performs basically the same as the Rock Pi 4A version (noted as rockpi4-rk3399 running Armbian), as expected. The Armbian OS (tested multiple times as rockpi4a-emmc, rockpi4a+, rockpi4a+governor, and rockpi4a+armbian) all perform terribly. Thoughts?

Hello, i want to use a NRF24L01 on my Rock PI 4B. I found out that i cannot enable spidev0.0 because this is corresponding with the network interface. Linux rockpi 5.4.32-rockchip64 #20.02.11 SMP PREEMPT Tue Apr 14 17:30:19 CEST 2020 aarch64 GNU/Linux Linux version 5.4.32-rockchip64 (root@builder) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #20.02.11 SMP PREEMPT Tue Apr 14 17:30:19 CEST 2020 My armbianENV looks like this: verbosity=1 overlay_prefix=rockchip overlays=spi-add-cs1 spi-spidev param_spidev_spi_bus=1 rootdev=UUID=3c50a1d1-71a5-4a0f-9899-099b17a1050b rootfstype=ext4 usbstora…

Hello everyone. Please help me with the following problem. I have a Rock Pi 4b 1.4 (with SPI flash). I did the boot from the NVMe SSD using the image rkspi_loader-v20.11.2-trunk-v2.img according to the instructions. I installed Armbian 23.11 Jammy XFCE on NVMe SSD KingSpec NX 1TB. I’m using a power supply Baseus 65W GaN Pro (with PD). The system loads and works well. However, the system cannot reboot. When i click on reboot, the system starts to reboot and after the reset goes into a cyclic reboot. I need to turn off the power to reboot. What could be the problem and how to solve it? UART (Serial console) log: " " $&0 f@`B@@NF0f@`B@@NF 0f@`B@@NF@@@LN`b`N" " …

I am observing huge difference in samba speed (both ways to/from PC on Gigabit Ethernet) with Rock Pi 4B. Earlier I had Debian and Ubuntu provided by Radxa and recently speed has gone from 115 MB/s to ~12 MB/s. I moved to Armbian which is currently available for download. Before any updates I had 115 MB/s transfer speed. When I updated to Armbian 20.08.11 Focal with Linux 5.8.15-rockchip64 the speed has go down to ~15 MB/s. The bigger change that happened was kernel upgrade. I exclude problems like: PSU (it is over enough), home network (nothing has changed) and SSD speed (checked - 330 MB/s). Has anyone else also observed limited speed rec…

Hi All! I've recently moved to Armbian (Debian buster server) on my Rock Pi 4B - from Ubuntu provided by Radxa (some way failed upgrade). However system is booting from eMMC which has Radxa kernel and then directly to Armbian file system on SSD connected via USB 3.0. Great is that Armbian is working with Radxa kernel, which I want to change to 5.8.14-rockchip64. My question is how should I prepare /boot folder on eMMC (which is FAT file system) to boot Armbian kernel? Is there any other way (reformat eMMC for ext4@32768 sector for /boot folder) to achieve this? Thanks.

I used iperf3 to monitor the LAN perferomance. It seems the LAN Port only runs on 100 Mbit how can I get a 1GBit speed ? Accepted connection from 192.168.xxx.xxx, port 64266 [ 5] local 192.168.xxx.xxx port 5201 connected to 192.168.xxx.xxx port 64267 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 10.7 MBytes 90.1 Mbits/sec [ 5] 1.00-2.00 sec 11.3 MBytes 94.8 Mbits/sec [ 5] 2.00-3.00 sec 11.3 MBytes 94.7 Mbits/sec [ 5] 3.00-4.00 sec 11.3 MBytes 94.9 Mbits/sec [ 5] 4.00-5.00 sec 11.3 MBytes 94.8 Mbits/sec [ 5] 5.00-6.00 sec 11.3 MBytes 94.7 Mbits/sec [ 5] 6.00-7.00 sec 11.…

Hello, I have been using Armbian OS on Rock Pi 4B. Full system is on NVME, not using SD card, and there is no eMMC chip on the board. During usage, I needed to shut it down improperly: by removing power cable, not through sudo shutdown now In the end I have following message during boot: Also, here is contents of dev folder: I was wondering if it is possible to fix this error. If not, I will reinstall with new image. Just spent much time on setting the environment, don't want to redo this all I would appreciate any help.

I am in the process to migrate a project from a Raspberry Pi 4B to a Rock Pi 4B+. Among others external devices shall be connected via WiFi AP, I2C, 1-Wire and UART to the Rock Pi. To emphasis, the system is running healthy on a Rasberry. I managed to get WiFi AP and 1-Wire up and running on the Rock Pi. Now I got stuck with UART/UART4. Armbian 22.11.1 Bullseye with Linux 5.15.80-rockchip64 I enabled UART4 via Armbian-Config. Therefore, /boot/armbianEnv.txt shows: ... overlays=i2c7 uart4 w1-gpio param_w1_pin=GPIO4_D6 param_w1_pin_int_pullup=1 ... I can take a jump wire and bridge the TX-pin (GPIO1_B0, Pin#19) and RX-pin (GPIO1_A7, Pin#21). W…

I can use echo 0 >/sys/class/leds/status/brightness to turn off the status led (blinking blue one, but I was to turn off the bright ass green one. I assume this is mmc1::, but I cannot turn it off.

Hi, hopefully my english and my linux skills are good enough (little bit experience with raspi and odroid i´ve setup Rock Pi 4 C with nvme boot from spi (first mmc) Armbian 21.02.3 Buster with Linux 5.10.21-rockchip64 after some difficulties to setup boot from nvme it is running on ADATA SX6000PNP when i perform reboot - mostly no reboot after disconnect power and reconnect no boot until i wait > 1 minute during the day i try sudo armbianmonitor - u and i get a link now when i use this command there is no more link serial console - i get no output but i can log in after a while Thanks

Problem: No usb power on all ports except for OTG port on Rock Pi 4C. Images: Ubuntu Bionic Legacy Desktop, Ubuntu Focal Legacy, Ubuntu Focal Current Desktop Monitoring information: Ubuntu Bionic Legacy Desktop - http://ix.io/2wlL Ubuntu Focal Current Desktop: http://ix.io/2wlZ

My system has: $uname -a Linux rkpi 5.8.11-rockchip64 #20.08.4 SMP PREEMPT Wed Sep 23 17:51:13 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux Sound stack seems to be loaded, but alsa/pulseaudio sees only hdmi-output device (aplay log below). How to enable analog ouput on 3.5 mm jack? $sudo aplay -lL default Playback/recording through the PulseAudio sound server null Discard all samples (playback) or generate zero samples (capture) samplerate Rate Converter Plugin Using Samplerate Library speexrate Rate Converter Plugin Using Speex Resampler jack JACK Audio Connection Kit oss Open So…

Hi all, new Rock Pi and as well new armbian user. After reading forum threads on the Rock Pi official forum, it seems possible to get the OS to run around 2W idle. I have installed cpufrequtils without getting any success, still sucks around 4W. Any help to tweak kernel or other activities to get Armbian to get into lower power mode would be appreciated. /Daniel

Hi, I have tried multiple Rock Pi 4+ (Plus) boards, all of them run regular Debian well, so the hardware should be good. But when I tried Armbian, the 2 USB 3.0 ports were not working with logitech USB dongle or Samsung USB drives (which did work in regular Debian), I searched and found maybe they were in OTG mode and needed to be in HOST mode. I tried armbian-config then System -> Hardware, then enabled: dwc3-0-host rockpi4cplus-usb-host After reboot, the bottom USB 3.0 port would start working, yet the top one still wouldn't work. Otherwise, Armbian was the most user-friendly, fast and stable…

Hi. At first I'd like to apologize for the tone of this post, but there are things that I've been fighting with, without any success, for a long time. Problem 1. I have, as it seems, a very common problem with Armbian on RK3399. I burned Armbian 23.8.1 for the Rock Pi 4C+ onto an eMMC module, which booted, but there is no HDMI video output. I can't SSH into it over ethernet and provide more details because the server is disabled by default. I assume that the problem here is the same one as I often see coming back to all RK3399 boards and the solution is always the same - "libreelec patches for the HDMI subsystem" (whatever they are). If it'…

Hello everyone, I seem to have a problem with not knowing how to change the top usb3 port of my Rock pi 4+ to host mode from otg mode, I just got it and installed armbian on it and open media vault, only to notice that I couldn't connect anything to the top usb 3 port and have it show up in open media vault, the other ports work fine and looking at the internet seems to have found that the answer is that the port is in OTG mode and on the official website they do have a way to change it to host mode, but not in armbian and I'm not skilled enough in linux to find where the file I need to change is. I'm running this build "Armbian_v22.05.2_Rockpi-4cplus_bullseye…

Would anyone be able to help me out with instructions for installing armbian to the EMMC of my Rock Pi N10? I've had Ubuntu installed using the OTG tool and also Armbian running off an SD card, but as soon as I run armbian-install and reboot the device doesn't come back up. Not sure what I'm doing wrong or the correct steps to troubleshoot.

My Rock Pi S logs a NULL pointer dereference in the ext4 module after running for 1 to 3 hours. Subsequently existing processes continue to run but it appears that new processes can't start (eg I can't ssh in). The filesystem is on a new Sandisk Ultra Plus microSD card. As a test, I remounted the root filesystem read/write and the board ran flawlessly for 10 hours. When I get time I will try rebuilding the image with the root filesystem on F2FS. Aug 31 09:31:27 rockpi-s kernel: [ 1944.993824] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000f8 Aug 31 09:31:27 rockpi-s kernel: [ 1944.994681] Mem abort info: Aug 31 …

Hi guys, I have checked the Buster image and stuck in following issue: On Rockpis, tty2 and (the only working) spi2 sharing the same PINs. Due to this reason, SPI is not functional . from dmesg: [ 1.598230] rockchip-pinctrl pinctrl: pin gpio1-22 already requested by ff0c0000.serial; cannot claim for ff140000.spi [ 1.598269] rockchip-pinctrl pinctrl: pin-54 (ff140000.spi) status -22 [ 1.598287] rockchip-pinctrl pinctrl: could not request pin 54 (gpio1-22) from group spi2-miso on device rockchip-pinctrl [ 1.598304] rockchip-spi ff140000.spi: Error applying setting, reverse things back I try to switch back tty2 to tty0 in dts and also…

Hi, I'm new to armbian and I've started with RockPi4b board. I would like to add fan control with PWM, but adding pwm (or pwm0) overlay doesn't work. I can't also find the overlay for it at /boot/dtb-5.8.6-rockchip64/rockchip/overlay/. Is it supported? I've checked and the /sys/class/pwm/pwmchip0 is present, but accessing export, as described here : doesn't work and /sys/class/pwm/pwmchip0/pwm0 is not present. I've tried to find pwm access examples for this board, but none of it works on armbian (all are vendor builds specific). Can anybody point me in the right direction or give any hint how to enable pwm? EDIT…

I had lost network interface when upgrade linux-image-vendor-rk35xx to 24.8.4 from 24.8.2 and reboot. I had downgrade to 24.8.2, then I got network interface. linux-dtb-vendor-rk35xx 24.8.4 linux-image-vendor-rk35xx 24.8.2 In other way, I had update bootloader by armbian-config to MTD-Flash then I got network interface. but, I had trouble in HDMI output that not display for two display, display only one. armbian-config 24.8.4 linux-dtb-vendor-rk35xx 24.8.4 linux-image-vendor-rk35xx 24.8.4 If you know of a cause, please provide informati…

With Linux rock-5b 5.10.72-rockchip-rk3588 #trunk.0102 SMP Sat Nov 5 07:56:18 UTC 2022 aarch64 GNU/Linux I see only one PWM controller pi@rock-5b:~$ ls /sys/class/pwm/pwmchip1/ device export npwm power subsystem uevent unexport pi@rock-5b:~$ cat /sys/class/pwm/pwmchip1/npwm 1 How do I figure out its header pin assignment? Is there a device tree overlay to expose all 4 PWM controllers?

Rock 5b test images, from armbian-next. Using vendor u-boot + patches, and vendor kernel, both straight from radxa's git XFCE desktop with "browsers" app group - https://github.com/rpardini/armbian-release/releases/download/20220710b/Armbian_20220710b-rpardini_Rock-5b_jammy_legacy_5.10.66_xfce_desktop.img.xz CLI - https://github.com/rpardini/armbian-release/releases/download/20220710b/Armbian_20220710b-rpardini_Rock-5b_jammy_legacy_5.10.66.img.xz PR: https://github.com/armbian/build/pull/3984 (against master) All work by @amazingfate I just gathered stuff and built images. Thanks to @monkaBlyat @lanefu @piter75 @amaz…

Hey guys, bunch of thanks for your great work. Was wondering what's up with the latest buster images (20.05.2-5.4.43) for the 1Gig A versions. Worked great up to 20.02.11-5.4.32. The boot gets up to changing the freq, then nothing : > change freq to 416MHz 0,1 Channel 0: LPDDR4,416MHz Bus Width=32 Col=10 Bank=8 Row=14 CS=1 Die Bus-Width=16 Size=512MB Channel 1: LPDDR4,416MHz Bus Width=32 Col=10 Bank=8 Row=14 CS=1 Die Bus-Width=16 Size=512MB 256B stride channel 0 CS = 0 MR0=0x19 MR4=0x3 MR5=0x6 MR8=0x0 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 M…

Hi I have spent couple of days to enable the SPI3 (the only SPI that has been routed to the 40-pin header) on Rock3A, but no success. I am trying to enable SPI3M1C0 with following pins on my Rock 3A GPIO4_C2 (CLK), GPIO4_C3 (MOSI), GPIO4_C5 (MISO), and GPIO4_C6 (CS0). I am out of idea, try different overlays but still not able to enable them. I used this overlay from this repo https://github.com/radxa/overlays/blob/main/arch/arm64/boot/dts/rockchip/overlays/rk3568-spi3-m1-cs0-spidev.dts I expect to see “/dev/spidev3.0” but nothing appeared. I have already added 2 overlays, 1 for 1-wire, and the other for I2C, and they are worki…

is there anyway to enable 1-wire, SPI3, and I2C3 interfaces? I have a hard time to deal with the overlay, but noting seems to be working.

I have a Rock4 SE Board (or Rock Pi 4 SE) and I'm using the Armbian_23.02.2_Rockpi-4b_bullseye_current_5.15.93 Debian version. (Linux rockpi-4b 5.15.93-rockchip64 #23.02.2 SMP PREEMPT Fri Feb 17 23:48:36 UTC 2023 aarch64 GNU/Linux) I am trying to set up the correct Device Tree Overlay configuration for my intended application. If I use Armbian-config as a tool to demonstrate the issue here. It starts by listing I2C7 and then I2C8. If I go to the Rock4 SE schematic and search for I2C8, it is not even setup as I2C: Then where is I2C6, for example. It's supposed to be there. If I then look fu…

When using the "boot from SD install to NVMe" option of armbian-config it offered the option to format the NVMe drive with btrfs. When I selected that option, it briefly flashed an error about the partition being too small (even though I had created a 120GB partition). The actual problem appears to have been that btrfs-progs was not installed. After installing that package and rerunning armbian-config it was possible to btrfs format and install successfully. I suggest the error message could be improved. Armbian_22.11.1_Rockpi-4cplus_jammy_current_5.15.80_minimal.img.xz

I have a RockPi 4c plus v1.41 with the Armbian Community version Armbian_community_24.11.0-trunk.202_Rockpi-4cplus_bookworm_current_6.6.53_minimal. Everything is okay, till i attach a dougther board (https://z-wave.me/products/razberry-old/) to the Rockpi. Normaly it boots fine from SDcard, but after attaching the that dougther board it won't boot anymore. It seems to stuck in uboot. I have done some boot logs, but everything before line 110 is identical WithDB.txt WithoutDB.txt

I don't expect an answer at this point but FYI, the eMMC on a Rock5a and latest image does not work properly. It mounts and as soon as you start writing, errors occurs and the FS (ext4) is remounted RO. It happens whether I mount and write manually or I use the armbian-config to transfer the system on the eMMC. Using the Debian distro of radxa, I can write as much as I want on the eMMC w/o errors, so it does not seem to be a failed module, rather something in the armbian kernel. 2023-10-10T17:05:03.106367-07:00 rock-5a kernel: [62335.087809] Buffer I/O error on device mmcblk0p1, logical block 648585 2023-10-10T17:05:04.109720-07:00 rock-5a kernel: [62336.091…

Moderator edit (pfeerick): I have modified this post to contextualise this split thread. It was initially intended to be a discussion of a board bring up procedure / proposal format, and has since evolved into discussion of the rock64 generally. Xalius originally said in this post: TODO-List sounds good to me, I will run some tests as soon as China Post/DHL actually deliver my package. I get a 4GB version with the suppressor diodes for USB3 already replaced... This is what tkasier originally wrote in his first post, minus the disclaimer as was only relevant to that thread:

Hello, I want to try out Armbian OS as opposed to Ubuntu Artful 17.10 on my Rock64, mainly to see how it compares(I am aware Armbian minimal for Rock64 is derived from Ubuntu Xenial, but I understand it's optimized for ARM CPUs) Long story short, I have a 32GB eMMC and a eMMC to USB adapter from Pine64 and would like to run Rock64 Armbian off it, but I was unable to simply flash Armbian to it using 'dd' or Etcher as with ayufan's Ubuntu images. I am aware it's possible to boot from an microSD card and use the "nand-sata-install" bash script to achieve this as described in the Armbian documentation, so I am inquiring if I can bypass usin…

I have been testing the latest Buster Server builds - kernels 4.4 and 5.3 versions on my rock64 board In both cases I see a number of syslog entries relating to device ttyFIQ0 not starting. Does anyone else have this issue? Any ideas how to remove stop it from trying to start? thanks

Hi, I have an Rock64 v2.0 and after update to trunk 24.8.0-trunk.369 to 24.8.0-trunk.399 the OS stop to starting process with this kernel error: U-Boot 2022.07-armbian (Mar 14 2024 - 00:34:55 +0000) Model: Pine64 Rock64 DRAM: 4 GiB PMIC: RK8050 (on=0x40, off=0x00) Core: 229 devices, 25 uclasses, devicetree: separate MMC: mmc@ff500000: 1, mmc@ff520000: 0 Loading Environment from MMC... Card did not respond to voltage select! : -110 *** Warning - No block device, using default environment In: serial@ff130000 Out: serial@ff130000 Err: serial@ff130000 Model: Pine64 Rock64 Net: eth0: ethernet@ff540000 Hit any key to stop autoboot: 0 Card did not…

I have Rock64 Ver.2 - 1gb model. Was working fine with Armbian 24.5.0-trunk.211_Rock64_bookworm_current_6.6.21 - boot from micro SD card On SSH, I updated to latest version Armbian_25.2.1_Rock64_bookworm_current_6.12.13. Now it does not boot from micro SD card. I had another micro sd card. I flashed new Armbian_25.2.1_Rock64_bookworm_current_6.12.13 - does not boot. I had another micro sd card. I flashed OLD Armbian 24.5.0-trunk.211_Rock64_bookworm_current_6.6.21 - it boots. Then updated to latest Armbian & does not boot anymore. Looks like some " Flashing_u-boot_to_SPI_Flash " - problem. Please help. Thanks in advanced

Hi, my rock64 (rev2) with the latest build of Armbian randomly looses its network connection. I couldn't use the armbianmonitor -u as it had no network connection, but when i use ifconfig, I can see it's still got it's settings and is the NIC lights are on. ifconfig showed 6 TX errors. My NIC is set to DHCP with static reserved IP address to an ASUS router. I leave it on 24/7 and check it once a while as it pretty much is used as a NAS with a single USB 3 drive. This morning I connected up via HDMI and a USB keyboard and logged in successfully. I don't have much Linux experience so wasn't sure how to capture the logs to SD card so i could co…

Hi! I've 2 rock64 boards -- 4gb and 2gb bought with 1 year difference The problem -- both boards have same MAC address. Changing it with macchanger has no effect, same for cloned mac in nmtui. Also I tried this in armbianEnv.txt: root@rock64:~# cat /boot/armbianEnv.txt verbosity=1 overlay_prefix=rockchip rootdev=UUID=48ad169b-7620-4c84-89fa-6c9a0fcde766 rootfstype=ext4 ethaddr=a7:71:b0:90:17:1f usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u But mac stays the same. I've plugged usb ethernet just to avoid conflict on same network, but how can I change the MAC of eth0 ?

How do you control which PHY the Rock64 is going to use? Android 9 is available for Rock64 now, https://github.com/a9rock64/manifests But it is configured to use the internal PHY and I need to change it over to the external one. Is this controlled in the DTS or someplace else? It is running on this kernel: https://github.com/rockchip-linux/kernel

The wireless interfaces are not coming up [ 16.959456] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 16.969238] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 16.971635] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 16.971650] cfg80211: failed to load regulatory.db [ 41.751941] rk_gmac-dwmac ff540000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 41.751976] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

Hi all! I'm having strange issue with Rock64. I downloaded latest Armbian 5.88 with 4.4.180 kernel. Installation and boot are ok, but when I try to do apt-get install lvm2 Package installs, configures and... update-initramfs: Generating /boot/initrd.img-4.4.180-rockchip64 update-initramfs: Converting to u-boot format Then I do root@rock64:~# sudo reboot And I'm getting a boot loop... Same effect, if I move system to SSD. At first I thought it was issue with ssd transferred system... But it clearly reproduced on freshly written with uSD only boot. I've dumped armbianmonitor output (ju…

Hello, Each time I'm booting the Rock64, it starts on Jan, 21 of 2016 but the filesystem has a superblock on Jan,28 of 2018, so in the future. It's inconsistant and the filesystem is checking each time and I'm waiting a few seconds. How can I avoid this trouble ? Here is the screen shot of logs through the tty/usb console. I'm booting from the spi flash and a sd-card with Ubuntu 18.04.1.

Hi. I have problem with Rock64 and ICYBOX IB-RD2253-U31 (USB3.1 Raid Enclosure) Kernel: Linux rock64 4.4.167-rockchip64 #3 SMP Sat Jan 12 18:58:23 CET 2019 aarch64 GNU/Linux dmesg on ICYBOX connected: [ 3.112348] usb 1-1: New USB device found, idVendor=1234, idProduct=5678 [ 3.112362] usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 3.112368] usb 1-1: Product: ASM1352R-Safe [ 3.112374] usb 1-1: Manufacturer: Asmedia [ 3.112379] usb 1-1: SerialNumber: 123412341249 [ 3.113303] input: Asmedia ASM1352R-Safe as /devices/platform/ff580000.usb/usb1/1-1/1-1:1.0/input/input1 Rock64#lsusb -v …

Hi everyone, Big fan of debian based distro's. Have six Rock64's and looking for a newer kernel (4.9+) with default Ubuntu modules list. 3 have eMMC cards and 3 using the Pine64 USB->SATA adapter with SSD drives. I have powered usb hub, y cables, etc but am using USB2 without powered hub because it's reliable as is and USB3 boot with any distro power injection seems unreliable. Not too concerned about throughput. Ayufan's release bionic-minimal-rock64-0.7.11-1075-arm64.img.xz with 4.4 is very stable on these. However Ayufan's mainline kernels after 4.4 are stripped right back. I spent a couple days compiling kernels with Ayufa…

I'm considering buying a Rock64 4GB to use a Docker server running media apps (plex,sonarr,radarr,jackett,smb,etc). I already have a 64GB SD card available for this system, probably overkill, but I have it. I noticed another post saying the SD card performance is not what it could be. I'd like to hear from other have a similar setup to what I'm thinking about. Does it perform well enough for what you're using it for? What are you using it for? What kind of samba through put do you get on the USB2 and USB3 (perhaps with the USB3->SATA adapter) Thanks.

I tried the stable Arabian image for rock 64 and found out that full HD video is played with strong brakes, when playing HEVC image is missing How to force video to be reproduced normally, maybe I don't understand something ?

I'm trying to get a Rock64 board working with a wifi USB dongle, sold as RTL8188 and which is in fact a 8188eu. I use the latest armbian-buster as downloaded a few days ago. The dongle appears in dmesg when plugged in, but no module is loaded. I can manually load the 8188eu module and get no errors, but no wifi interface appears. Ifconfig, iwconfig and nmtui don't see anything they could use for wlan. I have installed the firmware-realtek package as well, it made no difference. I can get the module 8188eu autoloaded at boot, but that doesn't change the non-availability of a wlan interface. Any help appreciated. I have posted the armbianmonitor -u output in the…

Running latest Jammy image and trying to attach USB to SATA 3 SSD. I tried two different USB 3 to SATA adapters and they both show up in lsusb: Bus 005 Device 002: ID 2109:0711 VIA Labs, Inc. VL711 SATA 6Gb/s bridge sudo fdisk -l doesn't show drive, but I can plug into my desktop and it mounts disk. Could be related to https://github.com/MichaIng/DietPi/issues/5378

Just got a rock64 board and tried the armbian testing image. Is ethernet working out-of-the-box with this image? My ethernet isn't working. Also the normal password didn't work (root / 1234). Would be nice to have some infos about that.

Hi, Is it possible to boot from SSD? How it should be partitioned? Can I use any arbitrary partition for rootfs? Should I follow the procedure from this thread ? It assumes I should write the armbian image to a whole drive instead of partition, right? Well, I actually tried some way... First, I've tried to just run some utility from ambian-config that transfers rootfs to a partition. Device did not boot after this (with SD card ejected). Then I've flashed the ayufan's u-boot-flash-spi-rock64.img.xz. This also fails (boot log is attached) but the log looks promising. BTW, I'm experimenting with Ubuntu 18.04 image built by myself …

I'm building a portable battery powered NAS because syncing and having everything multiple times on all my Android devices sucks. I took my old Banana Pi connected a SSD to the SATA port and made it a access point (no Samba yet installed). Booting from the 16GB SanDisk Ultra A1 is 27 seconds. Moving everything to the SSD in armbian config is also 27 seconds (no difference?) I know the Banana has not the fastest SATA and NIC and that USB 3 on the Rock64 is faster. But i don't copy tons of gigabyte to the device everyday and for streaming over the WiFi stick it's fast enough. I'm interested on the boot time of the Rock64 (e…

Good morning: I've got a ROCK64 and it does't boot from few days. White; Red and Green led stand with light. nothing change even after minutes. I've tried rock64-debian-mrfixit-190531.img.xz, , freedombox-bookworm_all-arm64.img.xz, debian-12.11.0-arm64-netinst.iso, But never go further. Do you have an idea ? I've got a 5A power so should not be a problem.

Hello, I've followed the steps on the Rock64 Armbian download page to enable overclock on my Rock64 running Armbian Xenial 5.60 (rock64 4.4.124-rk3328), yet I can't seem to increase the CPU clock frequency. I've also checked the Documentation-> Fine Tuning page where the same steps are listed. Steps: sed -i "s/MAX_SPEED=.*/MAX_SPEED=1510000/" /etc/default/cpufrequtils systemctl restart cpufrequtils I've checked the CPU frequency now and it looks like it's stuck at the default value. Shouldn't the new CPU frequency now be listed as 1.51GHz by the below commands ? rock64:~$ cpufreq-info -c 0 cpufrequt…