Rockchip

Hi! I was happy running Armbian on my Rock5, but for the second time in a week I got this panic: The journal from that boot seems empty: Any suggestions on how to debug/improve this? Thanks!

Hello, i did an update of the system (apt dist-upgrade), and after the system doesn't start anymore. I use internal MMC, so I tryed to use last Armbian buster (Armbian_21.02.3_Helios64_buster_current_5.10.21.img) from sd card and it works. I mounted the MMC, fsck and finally chrooted into it and did an apt update and dist-upgrade, I atach the console log, the system hangs on Starting Kernel. helios64_20210514.txt

I just installed Armbian 5.88 for Rock Pi 4B and bluetooth is not working. I'm using ARMBIAN 5.88 stable Debian GNU/Linux 9 (stretch) 4.4.180-rockchip64 Do you need further information? Got it working without compiling the new kernel. i manually ran the last steps of https://github.com/armbian/build/blob/master/config/sources/rockchip64.conf and copied rk3399-bluetooth.service and brcm_patchram_plus_rk3399 onto the device and set up the service... after a reboot Bluetooth is working fine. Thats great!

My NAS do very little overnight so my NAS4 shuts down in the evening and shortly afterwards a physical time switch cuts the power - reinstating power in the morning at which time the NAS4 automatically reboots. I want to do the same with the NAS64 - but even though I've read this (https://wiki.kobol.io/helios64/auto_poweron/) I'm not sure how to go about it. I can't understand if it only works if the UPS has died, or if I have to run a script before shutdown or both. Could you please clarify? Thx ... Nick

Hey there, I just joined the ARM universe & to be honest I lost all my skills with Linux. First I tried some official images Armbian_22.11.1_Rockpi-4cplus_jammy_current_5.15.80_xfce_desktop.img & with all of them I got a Blackscreen after the Logo. (all settings were made) Then I a tried a pre-release so I could finally get into armbian. Wifi : I couldn't connect via. wifi, "wifi network could not be found" But it was listed with a good signal strength. BT: no adapter was found. ( I used armconfig to enable BT) USB: just 3 of 4 usb ports were working. ( I guess it was 1x usb 3.0 & 2x usb 2.0) The Rock P…

Setup: Helios64 with Armbian 20.08.8 Buster with Linux 4.4.213-rk3399. Will change to Linux 5.8 soon though. 5 x 8 TB drives. Not using battery. I’ve had this issue ever since beginning to use my Helios. It first happened when I tried building a RAID with OpenMediaVault: It would crash and reboot while building. Sometimes after only 10 minutes, sometimes after 8+ hours of working. The same is true for video transcoding nowadays: it will sometimes crash after a little while, sometimes after a few consecutive hours of working, but it will never be able to work much longer than 12 hours on such a task. Copying large files from the internet has a similar risk of c…

Hi, I'd like to control ws2812 led's via gpio spi. I'm using this octoprint build by ldiaz: I checked /boot/armbianEnv.txt and there's overlay_prefix=rock64 and after enabling spi via armbian-config also overlays=spi-spidev. Then I rebooted but ls /dev/spi* shows nothing. Can anyone help?

Cannot connect to wifi via on-board wifi on Station P1. External USB WiFi controller (rtl88x2bu) works fine on the same board $ cat /boot/extlinux/extlinux.conf label Armbian kernel /boot/Image initrd /boot/uInitrd fdt /boot/dtb/rockchip/rk3399-roc-pc-plus.dtb append root=UUID=d98925da-408f-480e-b729-321ddcdbd2b8 console=ttyS2,1500000 console=tty0 rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 bootsplash.bootfile=bootsplash.armbian $ uname -a Linux station-p1 5.15.25-media #22.02.1 SMP PREEMPT Sun Feb 27 09:07:40 UTC 2022 aarch64 GNU/Linux $ journalctl -u NetworkManager ... …

Hi, Just noticed image " Linux rockpi-4a 5.9.14-rockchip64 #20.11.4 SMP PREEMPT Tue Dec 15 08:52:20 CET 2020 aarch64 GNU/Linux " my rockpi4a runs at 2Ghz. To radxa overclocking is possible so that 2GHz is not a real surprise ... Though checked " armbianEnv.txt " but did not find any "overlays" option present overlocking this board, neither any other files in /boot ( or /boot/dtb/rockchip/overlay ). However building a custom image ( kernel 5.10 ) it is running at 1,8GHz again, how can I set this to 2GHz ? ( as a side note - tehre is no need to enable panfrost BTW as I run this as a headless server ) Thanks

Hi, I'm trying to build the Armbian for Rock64. Host machine is Ubuntu 24.04 AMD64 (but it is running in VirtualBox under Windows). Build fails with the following error: [🐳|🌱] Deploying qemu-user-static binary to chroot [ qemu-aarch64-static during image-early ] [🐳|🔨] '/usr/bin/qemu-aarch64-static' -> '/armbian/.tmp/rootfs-232e77ba-e6ab-4067-8029-afd44bd1d0b9//usr/bin/qemu-aarch64-static' chroot: failed to run command ‘/bin/bash’: No such file or directory [🐳|💥] Error 127 occurred in main shell [ at /armbian/lib/functions/rootfs/distro-specific.sh:276 create_sources_list_and_deploy_repo_key() --> lib/functions/rootfs/distro-speci…

I think I found a regression: It seems the USB 3.0 port is not working with kernel 5.10.160. It was working with kernel 5.10.110. So I have two questions: 1. How do I file a bug-report ? 2. Linux 6.3 officially supports the rockchip-rk3588 (6.4 is out). When can we expect a kernel update and which kernel version would that be? Thank you

Hi, when I used rsync to copy several GB of data from the NMV3 to a USB SSD, the SSHD crashed. [96500.101926] ------------[ cut here ]------------ [96500.102376] kernel BUG at arch/arm64/kernel/traps.c:405! [96500.102858] Internal error: Oops - BUG: 0 [#2] PREEMPT SMP [96500.103343] Modules linked in: sg uas hci_uart bluetooth cpufreq_userspace zstd zram dw_hdmi_i2s_audio rockchip_rga v4l2_mem2mem videobuf2_dma_sg panfrost fusb302 tcpm videobuf2_memops gpu_sched typec videobuf2_v4l2 videobuf2_common videodev mc brcmfmac brcmutil cfg80211 rfkill rockchipdrm analogix_dp dw_mipi_dsi dw_hdmi ip_tables ipv6 crc_ccitt phy_rockchip_typec phy_rockc…

Hello all, I have a RockPi 4B in use and wanted to connect my 7" display from Raspberry via the display port. According to these instructions, it should also work. https://wiki.radxa.com/Rockpi4/hardware/display#Raspberry_Pi_7_inch_Touch_Display But unfortunately I can't find this file under "boot" because I'm using an ARMBIAN image. How can I address this 7" display? Can anyone help me here? Best regards from Berlin Z. Matthias

6 days ago I did a usual "apt-get update && apt-get upgrade" which brought up the following output: rock@rock-3a:~$ sudo apt-get update && sudo apt-get upgrade && sudo apt-get -y autoremove && sudo apt-get -y autoclean OK:1 http://deb.debian.org/debian bullseye InRelease OK:2 http://deb.debian.org/debian bullseye-updates InRelease OK:3 http://security.debian.org bullseye-security InRelease OK:5 http://deb.debian.org/debian bullseye-backports InRelease OK:4 https://box64.debian.ryanfortner.dev/debian ./ InRelease …

Configure Orange Pi 5B with Armbian OS so that it displays as a microphone and speaker when connected to a PC via the Type-C port, need to ensure the correct setup of the sound card. When connect Orange Pi 5B to PC via the Type-C port, it should now recognize the Orange Pi as a microphone and speaker. Please provide detail guide and suggest to achieve this setup

Hi all, I discovered this distro through FriendlyElec and I think it is the perfect hybrid of deb and wrt, but the only image is a file system, it doesn't even boot. All FriendlyElec's official ones are from 8 partitions with: boot, rootfs, kernel, etc, this one has everything in one and I don't think it's good for a mini device that runs in blocks like any openwrt. Has anyone installed on the r5c? How, is there a clean way to recreate the partitions? (note on boot: I turned on with sd and mask calc, steady red light, and eth mail router doesn't see it either. With friendlywrt and bullseye everything was working) Edit light blinks, I was confused between usbim…

Hi all, I have found a weird condition. I have a home built image running off sd card with no probs. my EMMC has friendly distro on it. I ran nand-sata-install to install armbian to EMMC. then I ran growpart and resize2fs against the EMMC and rebooted. afterwards, host failed to boot from emmc. so I thought "no probs, boot of sd". But SD failed to boot also. I tried same SD card in 1st gen nanopim4. boot happened fine. retried boot in nanopim4v2 and failed to boot. re-wrote arbian image and still failed to boot from SD. wrote friendly image to sd card and boot happened fine. ran dd against emmc and re-wr…

Good morning, I am an electronics engineer, and wanted to make an additional card for the nanopi neo3 based on the rk3328 to add an EMMC and an SPI memory to it so that it no longer uses an sd card. By dint of searching the forum, I managed to modify the dtb files of the neo3 to include the spi@ff190000 of my neo3 and to make the dtbo files spidev and jedec. But unfortunately, armbian-config cannot finish the job. For information I use a N25Q064..3E (flashroom information with active spidev) and goes back well in /dev/mtd0 in jedec. but in my armbian i have no file /usr/lib/uboot***spl.bin. Maybe the problem …

Hello people I would like to share my experience with the Mekotronics R58 mini PC (RK3588 box, in my case with 8Gb RAM and 32Gb EMMC). For a more review like post see NicoD's video review here on the Armbian forum: he just reviewed the new MonkaArmbian on this board. I got the Download links from NicoD, and in the meantime they are also on the official Mekotronics support site. I just want to share my experiences with others. So first I played a bit with Adroid 12, that came with the box. Android is the best supported OS for this box, performance wise. Video and emulated gaming seems to work great also 4K. But I wanted Linux on it, so I installed Debian from …

I have an FriendlyElec M4v2 board without eMMC card. (so i only use SD card) I tried this image: Armbian_21.02.1_Nanopim4v2_focal_current_5.10.12_desktop.img I Wrote to SD with Balena Etcher. After the new installation I turning on my board, I see my two attached .jpg file contents on the screen and after my screen flashes and immediately turns off my monitor (with no signal text on the screen) and if then I can only see Armbian again if I turn my monitor off and after on. So the Armbian is booting in the background, just need an HDMI channel refresh with a monitor physical off and after on. Then I installed all updates ('apt up…

I bought a NanoPC-T4 development board designed by friendlyelec and installed the Armbian operating system. But the heat generated by the Rk3399 main control chip is too high. I bought an official PWM fan. According to the official wiki, the fan can work normally. However, under the same configuration under Armbian, the fan can’t work normally, so I What work needs to be done? Thanks.

Hello I'm trying to install ZFS on the recomended armbian 4.4 bionic image for Nano PI 4 V2 (this is the default kernel) : uname -a Linux nanopim4v2 4.4.210-rk3399 #3 SMP Sat Jan 25 14:13:06 CET 2020 aarch64 GNU/Linux It complains there are no kernel headers to build a module for the 4.4.210 kernel: " sudo apt install zfs-dkms ..... Building for 4.4.210-rk3399 Module build for kernel 4.4.210-rk3399 was skipped since the kernel headers for this kernel does not seem to be installed. ... ● zfs-mount.service - Mount ZFS filesystems Loaded: loaded (/lib/systemd/system/zfs-mount.service; enabled; vendor preset: …

I was wondering if the Armbian 11 Bullseye release would get a release candidate for the following ppa's for Panfrost: ppa:liujianfeng1994/panfork-mesa ppa:liujianfeng1994/rockchip-multimedia Because I was really hoping to use Debian over Ubuntu for my purposes of familiarizing myself with the distro, but only Jammy so far has a candidate for these. I also tried manually installing the Panfrost/Panfork drivers on Bullseye and only got it working once before borking my entire system, and I cannot replicate it. Any help or information would be greatly appreciated, as the GPU acceleration on Jammy is simply amazing!

Hi, I owe a rockpi4a which I like to reflash with a custom build dev image: ./compile.sh BRANCH=dev RELEASE=buster BUILD_MINIMAL=yes BUILD_DESKTOP=no KERNEL_ONLY=no KERNEL_CONFIGURE=no BOARD=rockpi4a Can I flash this image directly to emmc, so it boots from it ?

steps to reproduce: 1. download official stable images and extract 2. write either image (both fail in same way) to sdcard: Armbian_5.91_Nanopct4_Debian_buster_default_4.4.179.img Armbian_5.90_Nanopct4_Ubuntu_bionic_default_4.4.179.img 3. boot sdcard -> works fine 4. run armbian-config -> firmware update 5. (also tried "apt update && apt full-upgrade", same result) 6. reboot -> boot loop happens every time, either the ubuntu or debian versions of armbian. no changes made after booting beyond just doing the update. reliably boot loops (it makes it to booting the kernel, then the board restarts after a while of no output) …

The alpha version of Armbian images for R57 with kernel edge 6.15 is now available Kernel is powered by HW panfrost acceleration on Gnome (wayland) and on XFCE (x11). Please note that in this version, the primary settings are enabled on the UART console, and to use the keyboard, you need to log in as ROOT with the password 1234 https://disk.yandex.ru/d/1M9FUcTqn5kEOw offtopic Libreelec for Mekotronics R57 https://forum.libreelec.tv/thread/20823-unofficial-le-for-rk356x-rk3328-rk3399-rk3588-s-rk3576/?postID=199809#post199809 Armbian 25.04 Noble ttyS0 r57 login: root Password: ____ ____ _____ | …

Dear to all, I have a Helios64 unit with 2 hdd (both WD60EFRX). I have bought also an external enclousure UGREEN 5 Bay Hard Drive Enclosure ( https://eu.ugreen.com/collections/hard-drive-enclosures/products/ugreen-5-bay-hard-drive-enclosure-5-x-18tb-raid-array-hard-disk-docking-station ) and 2 WD140EDGZ and these 2 hdd are mounted inside UGREEN enclousure because I want format and test it (when all will work fine I'll exchange a WD60EFRX with a WD140EDGZ so the drives inside the enclousure will have a backup scope). The enclousure is powered by external adapter, the system image installed is the Armbian 22.02.1 with Linux kernel 5.15.93-rockchip 64 and openmediavault 6.6…

I was cleaning storage room of customer and found this device in sealed box. Owner of the box say it was rarely used and i can keep it. Only thing broken was the battery. I replaced it temporarily with unused smartphone one. The device boots and is almost new condition. SoC RK3066 = (ARM Cortex-A9 Dual-Core @ 1.6Ghz + ARM Mali400MP4) RAM 1GB = (Four Chips on image are Hynix [H5TQ2G83CFR-H9C] -2gb) Storage 16GB = (Toshiba TH58TEG7DCJTA20 - Nand Flash MLC 16GB) Uart RX/TX pads on board I make this topic as i want to ask more experienced people here if this SoC can run "some" version of Armbian. Thank you in advance

I am trying to provision QEmu/KVM to run a Kubernetes cluster based on Ubuntu Cloud Image instances. I am using the latest release of Armbian on 16GB Rock 5B. Release kernel. After a relatively smooth setup I am able to provision and run instances. virt-install --connect qemu:///system --virt-type kvm --name virt1 --ram 2048 --vcpus=2 --os-variant ubuntu22.04 --disk path=/root/VMImages/virt1/virt1.qcow2,device=disk --disk path=/root/VMImages/virt1/virt1-seed.qcow2,device=disk --import --network network=default,model=virtio,mac=$MAC_ADDR --noautoconsole Everything works and I am able to log into the instance, but for some reason I am see…

Hi! In the Kobol wiki, there are 2 supported kernels : 4.4 and 5.10 In the armbian-build GIT repo, I see also patches for 5.13. What is the status of the 5.13 patches for the Helios64? Kind regards, Xavier Miller

I tried to install Armbian_22.11.0-trunk_Rockpi-4b_bullseye_current_5.15.76_minimal.img.xz from https://github.com/radxa-build/rock-pi-4b/releases/tag/20221101-0235 After first reboot main partition goes readonly. Checking disk show free cluster records mismatch. It is not SD-card issue, because Ubuntu Server on same SD-card working perfectly.

Hello, Recently I tried to make pwm control on my Nanopi M4. Beside the PWM pin on the 24 pin connector (the one which actually controls the voltage output on 12V 2 pin connector for fan), I wonder if it is possible to use GPIO pins on the 40 pin connector as pwm pins to control fans. I tried to set pwmchip0 and literally checked every pin by connecting the wire to each one of them but I couldn't find that any othe these GPIO react on any settings I made on pwmchip0 pwm0. Does anyone know how to do this? Best Regards.

Armbian 22.11.2 Cinnamon desktop was successfully installed onto eMMc storage from a microSD card. However, after installing the 3D accelleration following the official Armbian instructions, the Rock 5b failed to load the desktop. Instead, after the display of the Armbian splash screen, the screen turns black with a flashing white cursor. This problem started on 25 February. Before that day, 22.11.2 Cinnamon desktop successfully operated with 3D accelleration for two months. The following was used to install the 3D accelleration: sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia …

Hey! I recently accidentally made my eMMC unbootable. I ordered this adapter, but the eMMC isn't getting picked up by any of my microSD adapters. Is there a way to hotplug the eMMC chip while booting from SD, like with the Pinebook Pro (which is also RK3399 based)? I'd really like to either repair or clear the eMMC so i could continue using it. Thanks!

Hello, yesterday i see that the SATA Hat for the Nanopi is available now is it possible to install Armbian on a SSD when i use the Sata Hat ? Or is the EMMC or SD Card required for the OS ?

Hi, everyone. The Kobo site is kind of difficult to navigate if you're looking for relevant information, but I came to the conclusion that this is the right place for support. Forgive me if I'm mistaken. I was wondering if someone could help me interpret these bootlogs from serial term when trying to boot my Helios64 from the EMMC. Following the instructions on Kobol's site, I flashed their u-boot image to an sd card, booted the Helios64 off of said sd, fetched the latest image of Armbian, unpacked that image, and flashed it from my laptop to the Helios64 via usbc to what I presume is the correct interface. Could it be that I messed up? Here's a quick example …

I've got my helios64 recently, and I wonder what type of FS to choose for main storage. I have five 4TB disk drives. I've installed OMV, made raid5 and format it with XFS. I use XFS because I work with this FS on Centos on my x86 servers, I don't use ext4 because I don't like when sometimes it starts to check filesystem during boot process. My setup is working perfect for a couple of weeks. I don't have any reboots or freezes or any issues that I've read on this forum. Now I think about migrating from XFS to BTRFS or ZFS. The main reason is to have file check-summing and scrub. Does anybody have btrfs with raid5 or ZFS with raidz1 on Helios64? Do you have any problems wit…

Hello. I am trying to have the 1-wire working on Rockpi4B+ on pin GPIO4_D6 (= number 158). I have this /boot/armbianEnv.txt: verbosity=1 bootlogo=true overlay_prefix=rockchip fdtfile=rockchip/rk3399-rock-pi-4b.dtb rootdev=UUID=aa1f4e9a-bad9-4760-87c5-511247ef7227 rootfstype=ext4 overlays=w1-gpio param_w1_pin=GPIO4_D6 param_w1_pin_int_pullup=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u but when I check on my board: sudo cat /sys/kernel/debug/gpio GPIOs 0-31, platform/pinctrl, gpio0: gpio-4 ( |bt_default_wake_host) in lo gpio-9 ( |bt_default_reset ) out hi gpio-10 ( |reset …

after several minutes, a 3 line error message is output on 2 old original rock64's. network works, I can log in from my local net, and dmesg says: [ 35.867400] Unbalanced IRQ 47 wake disable [ 35.867422] WARNING: CPU: 0 PID: 1580 at kernel/irq/manage.c:900 irq_set_irq_wake+0x108/0x148 [ 35.867447] Modules linked in: rfkill joydev snd_soc_spdif_tx gpio_ir_recv rc_core lz4hc cdc_acm lz4 hantro_vpu(C) rockchip_vdec(C) rockchip_iep snd_soc_simple_card v4l2_h264 snd_soc_rockchip_i2s rockchip_rga videobuf2_dma_contig snd_soc_rockchip_pcm snd_soc_hdmi_codec snd_soc_rk3328 snd_soc_simple_card_utils v4l2_mem2mem snd_soc_rockchip_spdif videobuf2_dma_sg videobuf2_vmal…

What am I missing ? Just flashed Armbian_20.11.7_Nanopim4v2_buster_legacy_4.4.213_desktop on a SD card and the NanoPi does not boot. I get a steady red led and no flashing green and nothing on the HDMI. I don't get that problem when Flashing the eMMC...the problem is that I don't have that eMMC anymore and I am looking for a way to install Armbian on my NanoPi's NVMe SSD drive from the SD card. Any hints would be appreciated.

Hi, In a bid to solve an issue with my NAS (which I now think was a dying HDD) I foolishly decided to upgrade from buster to bullseye and now most, if not all, of the services are failing to start - including network-manager, sshd and fancontrol so I only have access via the USB serial console. By setting a static IP I have been able to get it network access at least. When I try to start any of the dead services it hangs for a minute or so, then kicks me back to the login and the terminal is corrupted so I need to reboot before I'm able to do anything meaningful. (I am able to start fancontrol by just running `fancontrol` at which point the fans stop going at 100%, s…

GPU can perform far better than CPU cores for certain applications. Computer vision is one of them. Orange Pi 5 GPU has 64 shading cores. It runs up to 19 times faster than 8 CPU cores combined for computer vision models. Armbian on Orange Pi 5 supports OpenCL driver for compute-intensive GPU programs. To install OpenCL on Orange Pi 5 Armbian, follow the instructions in the following link; Install OpenCL on Orange Pi 5 Armbian

Helios64 for sale. Works well. With battery. 2.5 lan mod haven't been done. Based in Germany.

Hi folks, I am puzzled. When I am away for a few days I usually shut down my nas. It does indeed shut down but over night comes up again. Now I would like to know what triggers that unwanted restart here... I am currently on 21.08.3 Buster with Linux rockchip64 5.10.63 and do have OMV running... I could unplug the battery next time but I'd rather solve the issue the correct way. It's strange to me because I did not change any system parameters in OMV or via SSH. I do believe that an update to the latest kernel did mess things up. Where do I have to have a look?

Hey guys, bunch of thanks for your great work. Was wondering what's up with the latest buster images (20.05.2-5.4.43) for the 1Gig A versions. Worked great up to 20.02.11-5.4.32. The boot gets up to changing the freq, then nothing : > change freq to 416MHz 0,1 Channel 0: LPDDR4,416MHz Bus Width=32 Col=10 Bank=8 Row=14 CS=1 Die Bus-Width=16 Size=512MB Channel 1: LPDDR4,416MHz Bus Width=32 Col=10 Bank=8 Row=14 CS=1 Die Bus-Width=16 Size=512MB 256B stride channel 0 CS = 0 MR0=0x19 MR4=0x3 MR5=0x6 MR8=0x0 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 M…

Hello Armbian Rockchip community, I'm working on getting Armbian based on the 6.1 BSP kernel running on a custom RK3328 board (specifically the MKS SKIPR for a 3D printer). This board is very similar to the libre renegade rk3328-roc-cc - just a few minor GPIO pin changes are required. I want to use the 6.1 BSP kernel because I expect it to have mpp video encoding capabilities. There is an existing repo that has this board working on the 6.7 mainline kernel with a couple of gpio patches. I've made some progress but am running into issues and could use some guidance. So far, I've been able to: Compile and run the basic 6.7 kernel for the MKS SKIPR - fr…

Hi, any hope to have a 5.x server image with support for the M1 bluetooth soon ? Chris

But only when the connection is initiated by the remote host. iperf3 -s ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from nanopcT4, port 51356 [ 5] local nanopiNeo4 port 5201 connected to nanopcT4 port 51358 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 2.34 MBytes 19.7 Mbits/sec 108 1.41 KBytes [ 5] 1.00-2.00 sec 2.05 MBytes 17.2 Mbits/sec 100 2.83 KBytes [ 5] 2.00-3.00 sec 4.68 MBytes 39.3 Mbits/sec 220 5.66 KBytes [ 5] 3.00-4.00 sec 199 KBytes 1.63 Mbits/sec 24 …

Hi, To my side, below work in root but not with systemd service: # Helios64 PWM Fan Control Configuration # Temp source : /dev/thermal-cpu #INTERVAL=10 INTERVAL=30 FCTEMPS=/dev/fan-p6/pwm1=/dev/thermal-cpu/temp1_input /dev/fan-p7/pwm1=/dev/thermal-cpu/temp1_input MINTEMP=/dev/fan-p6/pwm1=40 /dev/fan-p7/pwm1=40 MAXTEMP=/dev/fan-p6/pwm1=50 /dev/fan-p7/pwm1=50 MINSTART=/dev/fan-p6/pwm1=20 /dev/fan-p7/pwm1=20 MINSTOP=/dev/fan-p6/pwm1=20 /dev/fan-p7/pwm1=20 MINPWM=20 To my side, below work in root and with systemd service: # Helios64 PWM Fan Control Configuration # Temp source : /dev/thermal-cpu INTERVAL=10 …

I have a Rock64, purchased in 2019, that has been running happily for 4 years. I was recently experimenting with hooking it up to a relay board and now I am unable to connect to the internet. I am unsure whether something is fried on the board itself or if this is a software problem I can fix, and unsure how to figure that out. Details I have learned more about relay boards now, so I'll do a few things differently and more carefully next attempt, but I had the 5v pin powering the relay board and the 3v pin, GPIO3_A4, and GPIO3_A5 connected to the control side to control two of the board's relays. When connected the Rock's power leds were still on, but eit…

Good job with Armbian, I just can't find the power management, DevTerm A06 has batteries. Maybe I'm blind, please tell me where to look.

My device is Station-M3. I download "Armbian 23.8 Bookworm Cinnamon image" and burn it to a sd card.When armbian startup ,display response is very slow and Cinnamon process occupy 150% and above cpu usage.So I decide to "Enable 3D Acceleration".I do this as follow: sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia sudo apt update sudo apt dist-upgrade when dist-upgrade has done,something wrong about libc6, maybe because V2.36 is replaced by V2.35.Then the whole system come to unstable，reboot only bring kernel Panic！ I decide to burn the image again，but how can I enable GP…

Hi, I was testing images for Orange Pi 4 w/o eMMC, official from site, Debian and Ubuntu from ARMbian, and suddenly any boots anymore. I tried desperately everything, write with another program, used dd for copy, pressed randomly bottoms attached in the back, then one time worked, but it crashed when i attached a keyboard. Later all my micro-sd cards worked, most of them are poor quality, could be that but idk, my power adapter came from official website. # ls usb doesn't show hid I have a cp2012 usb to tll, i can use it for serial debug ?

L.S. After installing Armbian_20.02.1_Rock64_buster_current_5.4.20.7z on my 4GB rock64 running on SD card - I could run for days 2 processes with "openssl speed" resulting in 2 CPU's 100% busy. - But when I added a third "openssl speed" it only takes minutes to freeze the board. - Further the "ondemand" scaling_governor is active (default setting) I noticed that distributed /etc/default/cpufrequtils contains line: ==> MAX_SPEED=1390000 This value is not in the list with valid values for this CPU : ==> 408000 600000 816000 1008000 1200000 1296000 1512000 After updating this to valid value and restart service …

Getting free() invalid pointer issue when installing / using python3. Could be dpkg issue as well ! When I did sudo apt update && sudo apt upgrade, it happened and hence I tried to reinstall. This issue occurs when trying to manage it with ansible as well. I think something might be wrong with the latest python. Board: Helios64 (I know, I know CSC) Chipset: RK3399 Apt install logs: Reading package lists... Done Building dependency tree... Done Reading state information... Done 0 upgraded, 0 newly installed, 2 reinstalled, 0 to remove and 0 not upgraded. Need to get 0 B/472 kB of archives. After this operation, 0 B of additional …

Using P14 in the documentation (https://wiki.kobol.io/helios64/usb/#serial-console) I am unable to get a serial connection to work. Has anyone been able to get UART2 debug Serial working using P14 and an FT232 USB cable? With Kobol plug pulled looking to just have this run in DAS mode over USB-C to still get use without fear but still need to maintain serial console to monitor booting as it sometimes locks up on boot. Downclocking to 1Ghz or below conservative seems to do a lot better but still looking to have remote debug console. When I try to connect I just get the follow error and no output. pl2303_get_line_request - failed: -32

I use Armbian_23.8.1_Rockpi-4cplus_bookworm_current_6.1.50_xfce_desktop and need the current headers but could not find them sudo apt search linux-headers do not show them. I need them for the procedure described here https://github.com/glasgowneuro/comedi_raspberry_pi_bullseye/tree/main in order to install missing kernel drivers (comedi usbdux-sigma) Can anyone help please!

Board Dimensions: 90mm x 122mm x 16mm Heatsink Dimensions: 100mm x 123mm x 19mm Weight: 253 g including heatsink Rockchip RK3568 Processor L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processorsQuad-Core Cortex-A55 (1.992GHz) ARMv8-A architecture with Neon and Crypto extensions Mali-G52 MP2 GPU with 4 x Execution Engines (650Mhz) 0.8Tops@INT8, integrated …

Hello......could anybody tell me at least which image i have to use if i want to build armbian for the FriendlyArm NanoPC-T4? Couldnt find anything...... Thanks

Hello all, I have this board and It's suffering crashes and reboots all day. I think the logs are stored in RAM because I can't never find anything related to this issue. Is there anything I can do to find the cause? Many thanks. Regards.

Hey there, I'm running Armbian 23.8.1 Bookworm with Linux 5.10.160-legacy-rk35xx on a Rock 5B and am trying to get zfs via dkms to work, but it won't compile. ... configure: error: *** None of the expected "file_fallocate" interfaces were detected. *** This may be because your kernel version is newer than what is *** supported, or you are using a patched custom kernel with *** incompatible modifications. *** *** ZFS Version: zfs-2.1.11-1 *** Compatible Kernels: 3.10 - 6.2 Error! Bad return status for module build on kernel: 5.10.160-legacy-rk35xx (aarch64) I'm attaching the full build log,…

I built up a NanoPC-T4 with a 240GB NVMe. I am using the supplied heat sink and the black metal case that FriendlyArm sells. While I was copying an image over I got a board failure. A reset and power cycle didn't work. The stat light no longer shows activity. Just power.. that is all. Amazon was great and replaced the board. I am in the process of backing up my NVMe. After the backup I will run an OS install and restore the image. Has anyone else ran into this ? The black metal case isn't hot enough to burn my hands.. it's just very warm to the touch,. Welcome to ARMBIAN 5.67 user-built Ubuntu 18.04.1 LTS 4.4.166-rk3399 …

Related to It looks like the problem's related to the USB autosuspend. Googling "xHCI host not responding to stop endpoint command." seems to say so. I've been trying to disable the USB autosuspend but no success. I followed all possible ways described in https://unix.stackexchange.com/questions/91027/how-to-disable-usb-autosuspend-on-kernel-3-7-10-or-above and https://www.kernel.org/doc/Documentation/usb/power-management.txt but $ cat /sys/module/usbcore/parameters/autosuspend always returns 2 Board: NanoPi M4, 4GB with Armbian_5.65_Nanopim4_Debian_stretch_default_4.4.162.7z

I have some bose speakers plugged into the A/V and i am getting no sound. does this feature work on the POCK 64? or is audio only through HDMI. my monitor has no audio support.

Hi All, I am on my Helios64 (already have a Helios4). I am running 2 x 8TB, 1x 256 M2, OMV5 debian etc. I have ZFS running (from the wiki instructions) in a basic mirror format, and if I add a few drives I think it would still be a mirror, however I have the following question. It seems far more complicated than MDADM, and potentially more unstable (not in terms of the underlying technology, but in terms of changing these kernals etc every week). Do you think for an average home user that this is really worth it or will constantly need work? To change it would mean starting again, but I do not want to change the setup every month and wo…

Hi, Thank you very much for the community support of Odroid M2. The latest release 25.5.0-trunk.256 works great, boot without any error messages. Only rolling release is available for now, but that doesn't matter. I would just like to ask for support on two issues: 1. monitor connection via USB-DP is not working - I don't know what is needed to make this connection work 2. some tree-overlay drivers specific to Odroid are missing - I mainly miss the ability to connect display-Vu8S (via MIPI-DSIdisplay_vu8s.dts). Source codes can be obtained directly from kardkernel images, but it is not in my power to compile them for armbian. best rega…

Hi folks, I got my helios64, assembled it during the weekend and can’t seem to actually install it. Here are some of the things I tried (I'm on windows 10 btw, I don’t have hdd drives yet, I assume this would not be an issue): · 2 sd cards (one of which is a Samsung as recommended in the wiki), two computers (with correct com ports as visible in the device manager, driver is installed), tried both on usb2 and usb3 · USB cable has been trimmed to fit the case properly - also tried with the back panel off and directly connected to the board · the devices starts up as soon as I plug in the power cord - I then use…

Tried installing rock 4se image and rockpi 4b image. Both blink the blue led but none gives me hdmi output or network connection. What is the correct image for this sbc? The silkscreen says rockpi 4 SE Thanks

I have Rock Pi4B and printer 3D Sapphire Pro from Two Trees. In the Armbian I want use print server OctoPrint. Instalation OctoPrint was easly and server works but don't connect to my printer. When I use lsusb i see Bus 004 Device 003: ID 1a86:7523 QinHeng Electronics HL-340 USB-Serial adapter. In the list dev/tty* don't shows me mounting port to this device. I try defined udev rules: SUBSYSTEM=="tty", ATTRS{idVendor}=="1a86", ATTRS{idProduct}=="7523", SYMLINK+="sapphire" or SUBSYSTEM=="tty", ATTRS{idVendor}=="1a86", ATTRS{idProduct}=="7523", ATTRS{devpath}=="1.2", SYMLINK+="sapphire" but without fine result. I'm rookie in linux and armbian and don't h…

Thank's for supporting Rock64! Is there a chance for a debian server image (beta) within the near future? All my boards are running a armbian debian OS and I would like to stay consistent here... Best regards Martin

HI guys, one guy at my server realized some nvme testing and the write speed results are far below compared to radxa official benchmark that's probably based on legacy kernel. anyone had better benchmarks on write speeds without legacy kernel (so, mainline)

I have a problem with remote desktop operation on R4S. It installs according to the RDP guide and unfortunately does not work properly, after installing vncserver I also have information about - Cannot find a running X server. Everything works fine on neo3, only here I have a problem. Log VNC xstartup terminated Sending TERM signal to Xvnc... X connection to :1 broken (explicit kill or server shutdown). FreeFontPath: FPE "/usr/share/vnc/fonts/" refcount is 2, should be 1; fixing. <13> 2021-03-16T17:40:30.716Z nanopi-r4s Xvnc[5435]: ServerManager: Server stopped Link Status R4S Please Help 1) Armbian_21.02.3_Nanopi-r4s_focal_curren…

Leapo has started porting RPi.GPIO to Rock64 as R64.GPIO, you can find her work in progress at https://github.com/Leapo/Rock64-R64.GPIO Original thread with instructions/updates is here: https://forum.pine64.org/showthread.php?tid=5902 She also made a more simple tool to work with GPIO: https://github.com/Leapo/Rock64-BashGPIO

Hi there, now I have pure bug report: done apt update + apt ugprade, GUI frozen, even no SSH, about an hour later (I was outside my house) (probably) restarted but up to multiuser, no GUI at all. Howeve I CAN log over SSH, sthe issue "startx", but ONLY as ROOT. (much indesired, as ex web browser should never be started as root). I can enable remote X in /etc/X11/xinit/xserverrc , then start remote X session. Also "init 5" attempts to start X, but crashes. How to diagnose and repair? Laurent

Hello, I just apt upgrade-ed my Armbian 25.5 from mid-August to 25.8.1 and it doesn't start after software reboot. It is usually headless, I plugged it into a monitor and all I get is a uboot logo in the top left corner. No message, nothing. The board is the Rockpi 4A. The system is on eMMC 😩 What do I do now to at least roll back ? At worst make a browsable copy of the eMMC ? Thanks! Antoine

Hey there, so I was curious is there an easier way to make microSD take precedence in the boot order then having to futz with jumpers? Wanting to try out a new distro on microSD before deciding to make the switch and flash it to eMMC. If I do futz with jumpers I'll still be able to mount and write to the eMMC correct?

Hello All, Preface: First time posting, I am not an experienced software developer but have designed a working SBC around the RV1126. I have had some success recently getting video out of an IMX258 camera connected to the RV1126 but I am experiencing a strange issue where the camera feed has a green hue. (see attached picture). I have tried to change variables within the kernel - IMX258.c and many other places to change the auto white balance with no success but have recently come across this thread which may provide better results: https://forum.pine64.org/showthread.php?tid=17067 I do not have the RKISP2_tuner.exe in the camera_engine_rkaiq …

Hi, in Germany electrical Power ist getting more and more expensive (reaching 30ct per kWh). So I am trying to work out a Desktop Usercase Scenario (Mail, Office, Browsing, Video Streaming, Audio Streaming) on a SBC System. My experience is growing in Using a Manjaro XFCE on the Pi 4B (4GB), Booting from SSD. It works very well, nearly like the former used Deskmini A300 with Athlon 200GE. And I also tried out the Jetson Nano, Ubuntu 18.04. On both Systems you can get a satifsfying Desktop Experience, but the Jetson with ist Cortex A57 Core Base is a bit slower, also while it is used from an micro SD SanDisk A1 Card. For a long time I ve been watching t…

Greetings to all! I want to share the news. 2020.07.21 Mainlinte U-Boot includes patches for Rock-Pi-N10. https://patchwork.ozlabs.org/project/uboot/list/?series=191290&state=* I am trying to build it and run. Everything compiles successfully, but during testing, an error occurs with an incorrect detection of the SDRAM size. On my model A (3GB RAM for CPU), 2 banks are detected at 1152, but it should be 1536. U-Boot SPL 2020.07 (Jul 25 2020 - 09:28:13 +0300) Trying to boot from MMC1 U-Boot TPL 2020.07 (Jul 25 2020 - 09:28:13) Channel 0: LPDDR3, 800MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=14/15 CS=2 Die BW=16 Size=115…

Hello, I have a problem, when I enter "sudo apt install zfs-dkms" on my Helios64, I get this error message: "Module build for kernel 6.6.36-current-rockchip64 was skipped because the kernel headers for this kernel do not appear to be installed." I also made sure to install the kernel header in armbian-config and also rebooted. When I type "apt list --installed | grep linux-headers", I get this listing: WARNING: apt does not have a stable CLI interface. Use it with caution in scripts. linux-headers-current-rockchip64/bookworm,now 24.5.1 arm64 [installed] omv7 itself is installed and running. …

To continue discussion from Helios64 Support Noted, we will enable ZFS support after Armbian 20.11 released. I will need your help to test since i don't have system with ZFS.

I don't know where else to share this so I'm putting this here. The board recognizes and tries to the load the driver for an AR9462 QCNA222 M.2 WiFi card, but fails. I tried a custom build found on Radxa forum/github, built Armbian myself, and tried an official build. All resulted in the same error. Card was tested and working correctly on 2 different Debian x86 machines. lspci 0000:00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01) 0000:01:00.0 Network controller: Qualcomm Atheros AR9462 Wireless Network Adapter (rev 01) 0002:20:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01) dmesg ath…

I saw there was a download of Buster minimal with 5.3 kernel on the nanopi neo4 page. But it just disappeared. So what happened to it? Is it still a nightly build (I see the Buster desktop with 5.3 kernel is supported)? Where can I download it now? Will it be available for downloading again? Thanks in advance.

So I did the upgrade to OMV6 (and associated kernel update Linux 5.15.93-rockchip64). Now in the mornings or after long periods of no interaction, the Helios enters an unresponsive state where none of the docker containers respond and I can no longer ssh in. There is still some sporadic noise comming from hard drives doing things and lights on the front are showing it's not completely frozen. I suspect it's attempting to enter some kind of suspend / hibernate state that is not appropriate for this system. Which would be the appropriate log file to go hunting for answers for sleep/hibernate issues on Armbian? And what w…

Has anyone managed to get Armbian on Orange Pi 5(b) output audio through the 3.5mm jack? The device seems to be recognised, but even after fiddling with everything imaginable through alsamixer, with speaker-test running in the background, I am unable to actually get any sound out. HDMI audio works without any problems. ChatGPT thinks it has something to do with GPIO routings not being properly set up. I'm running Armbian 25.2.3 noble (through `apt-get dist-upgrade`; I had to first install an older version from the archives to avoid bricking when installing on the eMMC). $ aplay -l **** List of PLAYBACK Hardware Devices **** c…

I had some troubles with the latest build (Armbian_23.05.0-trunk_Orangepi5_lunar_legacy_5.10.110). First I had to restore the 5b specific device tree (rk3588s-orangepi-5b.dts) because with the modified rk3588s-orangepi-5.dts the Wi-Fi and the eMMC doesn't work. So far everything works fine with the exception of the bluetooth. After each boot I have to manually attach it: hciattach /dev/ttyS9 any ...otherwise the hci_uart module is not loaded and no hci device is available. Once attached the bluetooth works fine and I can pair my mouse with it, but not my bluetooth keyboard?!? Seems like the adapter doesn't even detect the keyboard. W…

Title pretty much summs it up! I had a few problems getting my RockPi 4 to boot anything from SSD, but I did mangage too by compiling the current buster branch as a minimal image. I also created a thread on the radxa forum: https://forum.radxa.com/t/trouble-booting-armbian-from-nvme-ssd/4362 With the current image on the website (buster - server - 5.8.y) my bootlog looks like this: Spoiler DDR Version 1.20 20190314 In channel 0 CS = 0 MR0=0x98 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x3 MR5=0xFF MR8…

Hello, When choosing Boot from eMMC - system on SATA, USB or NVMe in armbian-install using the Armbian 24.8.3 Bookworm Minimal / IOT, Kernel: 6.1.75, Release date: Sep 14, 2024 image on my NanoPi R6C, I get the following error: The wird device name is also mentioned on the two preceeding dialogs ("it is highly recommended to wipe all partitions" and "this will wipe all data"). I took a look at the argmbian-install script and the check_partitions routine seems to assume that $diskcheck contains something that, when prefixed with /dev, can be used in the of parameter of the dd command. It is computed as root_uuid=$(sed…

I have an Orangepi5 ultra RK5388. I have tried the following versions of Armbian13. It doesn't recognize my USBs so I don't have a keyboard. vendor: https://armbian.systemonachip.net/dl/orangepi5-plus/archive/Armbian_25.8.1_Orangepi5-plus_trixie_vendor_6.1.115_minimal.img.xz.sha This one won't start ,current: https://armbian.systemonachip.net/dl/orangepi5-plus/archive/Armbian_25.8.1_Orangepi5-plus_trixie_current_6.12.43_minimal.img.xz There is also no reference to Debian13 in any repository on the Orangepi website.

Now the mainline u-boot has decent pcie and pcie phy driver for rk3399. The only deficiency is the clock of pcie phy not included. The first attached patch add this clock so that u-boot proper can load linux kernel residing in an ext4 partition of nvme ssd.pcie_phy_clk.patch The second patch enables loading the environment from a file in an ext4 partition of nvme ssd.env_nvme.patch More conveniently the u-boot proper(u-boot.itb) could be an ordinary file residing in an ext4 partition of nvme ssd. The idbloader(tpl/spl in spi/emmc/sdcard) could load it if pcie nvme support is enabled in spl. That's the third attachment.spl_nvme.patch Th…

Hi, I've booted the board from SD card with the latest image and I'm trying to configure the board to boot from MTD and use USB drive as a system drive. When running armbian-config (or armbian-install, or nand-sata-install), it fails with error "SPI u-boot image not found!". It looks like the bootloader package is missing the /usr/lib/linux-u-boot-current-rock64_23.02.2_arm64/rkspi_loader.img. Can I find it anywhere? Dmitry

Hi there, I'm using the latest version of armbian to run the linuxptp for the ieee1588v2 clock. When I check the timestamp status, the 1Gbps port which is the RTL8122 is no problem, but the 2.5G ports RTL8125BG are only supporting the software timestamp. However, when I checked the Realtek website, it says that the 8125BG also supports the IEEE1588 clock. I tried to install the driver, but it did not work. As a beginner in Linux, I probably don't have the knowledge to compile drivers, in this case I sincerely hope that armbian could officially support the hw ptp timestamp in 8125 NIC. Thank you very much! nanopi-r6s:~:# ethtool -T end0 Ti…

Last week I updated the Armbian on my NanoPi M4V2 to the latest version (Armbian 21.08.1 Buster with Linux 5.10.60-rockchip64) and started noticing some issues with my Zigbee2MQTT local install. With the help of the Zigbee2MQTT main developer, we managed to confirm that the issue was reproducible on 5.10.60, but everything was working fine on previous kernels like 5.4. Other users not on Armbian (Raspbian) also confirmed that they were experiencing this problem with the latest kernel but was working fine on previous versions. We realized a bug was introduced for the CH341 driver in 5.10.60, that seems to have been fixed now on 5.10.62. …

The link to nightly builds for the Rockpi 4C+ WIP on https://www.armbian.com/rockpi4/ is broken. (Perhaps it should link directly to https://github.com/armbian/community ?)

If you want to build out-of-tree kernel modules, you will need: kernel headers (installed with apt) kernel sources in /usr/src (cloned from git) kernel config (from /proc/config.gz) some preparation of the sources (but you can avoid building it 😉) # Install kernel headers apt install -y linux-headers-legacy-rk35xx # Install kernel source cd /usr/src git clone https://github.com/armbian/linux-rockchip.git ln -nsf linux-rockchip linux-5.10.160-legacy-rk35xx cd linux-rockchip git checkout rk-5.10-rkr6 # Prepare kernel source zcat /proc/config.gz >.config yes | make olddefconfig make prepare modules_prepare cp /usr/src/linux-headers-$…

Now I'm no expert but I got Mate working maybe there are some shortcuts I did not take, but it works great. So feel free to point out any flaws or improve it, #!/bin/sh -vx packages=' cryptsetup libblockdev-crypto2 engrampa firefox ffmpeg libavcodec-extra gufw lightdm lightdm-settings slick-greeter ubuntu-mate-wallpapers-common mate-desktop-environment-extras mate-applet-brisk-menu mate-applets mate-calc mate-indicator-applet ayatana-indicator-application ayatana-indicator-bluetooth ayatana-indicator-common ayatana-indicator-display ayatana-indicator-keyboard ayatana-indicator-messages ayatana-indicat…

I am trying to update my Banana Pi M64: missinglink% cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=bananapim64 BOARD_NAME="Banana Pi M64" BOARDFAMILY=sun50iw1 BUILD_REPOSITORY_URL=https://github.com/armbian/build BUILD_REPOSITORY_COMMIT=869a89d6-dirty DISTRIBUTION_CODENAME=focal DISTRIBUTION_STATUS=supported VERSION=20.05.4 LINUXFAMILY=sunxi64 BRANCH=current ARCH=arm64 IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image but when I run this command: missinglink% sudo apt update && sudo apt dist-upgrade -y I get these errors: W: An error occurred durin…

I've been hopelessly trying to get Armbian(Buster) and OMV to work together properly. But alas no luck. I decided to start over using a fresh and latest image on the SD card. I believe I may have unwittingly screwed up the eMMC boot process because I added an M.2 SATA drive in yesterday and have since removed it. Hence my quest to simply get the SBC up and running from the SD card. I have tried everything this morning, I cannot get an image to load at all. One of my questions is; do the hard drives need to be installed just to get the SBC working? I have tried with them in and out to no avail. Are there some lingering config files residing on the HDs th…

Fresh build edge bullseye image with kernel Linux helios 5.18.0-rockchip64 #trunk SMP PREEMPT Sun May 29 20:19:27 EEST 2022 aarch64 GNU/Linux fancontrol not work, because there no /dev/fan devices How to get fancontrol back to work?

Hello I was finishing setting up my Helios64 (system installed on emmc) with Openmediavault (luks + snapraid + mergerfs + samba) on 3 disks, everything was working and I thought I should reboot to make sure that it is indeed the case (especially making sure that luks locked disks would not be an issue). An what a surprise, after booting up I couldn't ssh in so I connect the serial to log in as root. It seems that all services are dead like below. # service ssh status ● ssh.service - OpenBSD Secure Shell server Loaded: loaded (/lib/systemd/system/ssh.service; enabled; vendor preset: enab Active: inactive (dead) Docs: man:sshd(8) man:sshd_co…