Orange Pi 5

Hello, I have an orange Pi5, i had installed armbian a few years ago and everything was working fine. Roughly one year ago i turn it off and kept off until now. A few days ago I tried to turn it on again and i've inserted a new sd card containing armbian but it doesn't boot. I've re created the sd card a few times and also used another sd card because i was thinking something was wrong with the card. The board turn on but i got only the red led, and is stable. Searching on internet i found that maybe the Orange Pi is bricked, so i tried to use the MaskRom and Recovery button, but nothing happen. Also i'm not able to see the board inside the RKDevTool, neithe…

Hello All, Do you also have this kind of messages in syslog ? [ 1601.687044] ------------[ cut here ]------------ [ 1601.687070] WARNING: CPU: 2 PID: 112 at drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2986 vop2_crtc_load_lut+0x54/0x310 [ 1601.687075] Modules linked in: bnep zstd joydev sch_fq_codel fuse ip_tables ipv6 r8152 panfrost gpu_sched [ 1601.687114] CPU: 2 PID: 112 Comm: kworker/u16:1 Tainted: G W 5.10.110-rockchip-rk3588 #trunk.0184 [ 1601.687117] Hardware name: Orange Pi 5 (DT) [ 1601.687127] Workqueue: events_unbound commit_work [ 1601.687134] pstate: 40c00009 (nZcv daif +PAN +UAO -TCO BTYPE=--) [ 1601.68713…

I have issues enabling hardware acceleration on Debian CLI, anyone had same problem? can someone give a tutorial?

Hello ! Not found any devices How to make it work? hciconfig -a hci0: Type: Primary Bus: USB BD Address: E8:48:B8:C8:20:00 ACL MTU: 1021:6 SCO MTU: 255:12 UP RUNNING PSCAN RX bytes:1537 acl:0 sco:0 events:148 errors:0 TX bytes:3430 acl:0 sco:0 commands:136 errors:0 Features: 0xff 0xff 0xff 0xfe 0xdb 0xfd 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH HOLD SNIFF PARK Link mode: PERIPHERAL ACCEPT Name: 'orangepi5' Class: 0x000000 Service Classes: Unspecified Device Class: Misce…

Hello, i'm using Armbian 23.11 Jammy-amazingfated Gnome. Kernel 5.10 If to seek a couple of times in h264 1080p BD remux'es it will cause system restart. Any video players are affected. Tried mpv, vlc, kodi and others. Problem affect just h264 1080p remuxes, that typically are 30..40 Gb, smaller h264 or even larger h265 files seem to work fine. I tried fresh install of armbian, where no rkmpp is installed, then h264 files plays/seeks fine, in software mode of course. Once I did sudo update/upgrade, that also installs rkmpp and other rockchip stuff, then videos start to play with rkmpp and problem is back. I've tried disabling hw deco…

Degin: MounlAng root Tile syslel ... Degan: munning escrapusr cucad-lop ... uonc. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. done. Geve up waiting for root file system device. Cowmon problems: ⁃ Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! UUID=db80a2ac-ec37-4fda-91db-92604becfcce does not exist. Dropping to a shell! BusyBox v1.30.1 (Ubuntu 1:1.30.1-7ubuntu3.1) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) …

hi all, so i skipped i beleive 2 releases of armbian for opi5 and i just downloaded latest and installed. i am not english native and armbian installs local langauge automaticaly wich is ABSOLUTELY NOT WANTED and quite annoying from my perspective. what i need is just plain en.us or english internatinal for system and keyboard but i cant get it. i tried changing it with armbian config but it doesnt do a thing, local language is always there and its a huge PITA. please armbian dudes, return to manual selection, i beg you. any tips how i can fix it so its just plain english? or how can i force installation to ask me what language to choose? thanks for an…

How do I get DVB drivers to work. I have a Technotrend TT Connect S2-3650-CI. All DVB drivers are missing

Hello all, I have noticed that whenever I reboot my Orange Pi 5 board, all the 8 cpus slow down to 408 Mhz with no range, as stated by cpufreq-info: I have created a cronjob script in order to bring the frequency back to acceptable range. I don't even know if this is the correct way to solve this, but I am running the following: echo performance | sudo tee /sys/devices/platform/dmc/devfreq/dmc/governor cpufreq-set -c 0 -u 1800000 cpufreq-set -c 4 -u 2260000 cpufreq-set -c 6 -u 2300000 cpufreq-set -c 0 -g schedutil cpufreq-set -c 4 -g schedutil cpufreq-set -c 6 -g schedutil However, even though I set the frequency for processo…

The overlay for the ap6275p seems to be missing in the new fresh 6.10 images. Haven't tried to compile a custom image yet (so might just be disabled in current build), but how could I help to bring this overlay to the official image?

My Orange Pi 5 with latest debian does not reboot. I use it faceless (without local screen) via RDP (LAN) from Windows, works fine. But I cannot reboot. Neither via RDP nor via SSH. The green LED stops blinking, the red LED continues. But no LAN access. Must do hard reset via button or power off/on. Any ideas?

I just installed the most recent nightly image - this one looks like a major update but it broke armbian on my opi 5 1. I had to re-install the mali firmware to get x11/wayland to start - not sure why the update deleted the file 2. I had to re-install the mali-g610-firmware rockchip-multimedia-config packages 3. VLC cannot start the h264 decoder anymore [0000005583627590] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface. Warning: Ignoring XDG_SESSION_TYPE=wayland on Gnome. Use QT_QPA_PLATFORM=wayland to run on Wayland anyway. [00000055836b79e0] main playlist: playlist is empty [h264_rkmpp @ 0x7f4cc37630] Failed…

Hi friends, I have one nagging thorn in my side that I just cannot figure out. I need someone who has a 1password account for help with this one. The problem - their desktop app and browser plugin work in tandem -- and it will not synchronize on Armbian for some reason. I've tried everything I can think of - ensuring nothing is downloaded from Flatpak and therefore sandboxed and preventing any connectivity issues. But still not working. If someone can take 5 mins and create a free trial account on 1password, then here are the steps to reproduce: Download the latest arm64 version of 1password Desktop: curl -sSO https://downloads.…

Hello, I'm using Ubuntu noble lts with kernel 6.1 it appears. I've enabled the orangepi-5-sata overlay. In the photos I have showed how I've connected it. When plugging in the pi with my official 5v 4a usbc charger, the adapter lights up for awhile. I'm not sure if it needs to stay on. I then check fdisk -l and nothing new appears. This drive works if I put the sata to usb connector on it and plug it in - so it's not the drive.

Yeah so just like the title says, has anyone got a tip for a USB Bluetooth dongle that works with the mainline kernel? I got a UGREEN Bluetooth 5.0 dongle a while ago and have just tried again, installing firmware for it. It does get detected as a USB device and the firmware loads. But bluetoothctl never finds it. Gnome doesn't let me 'enable' bluetooth. I'd like to avoid buying a string of these so was just wondering if any are working with mainline? Cheers!

flashed to m2 mvme, board attempts to boot , then after armbian logo it falls into busybox command prompt (

I run a audio loop code on a Raspberry pi 4/5 and Orange Pi 5. The latency of audio loop is 0.2 seconds on Raspberry pi but on orange pi it takes 1.2 seconds. For orange pi, i am facing this problem with different Operating systems as well apart from armbian. I've used Ubuntu, Orange Pi OS, Armbian. All have got this problem. The code I have attached. Since the issue is faced in multiple Operating System I strongly feel this has to do with the driver level softwares or directly related optimization from Rockchip. Can anyone guide what I could do audio-loop.cpp

$ neofetch ubuntu@orangepi5 ---------------- █ █ █ █ █ █ █ █ █ █ █ OS: Armbian (23.11.0-trunk.145) aarch64 ███████████████████████ Host: Orange Pi 5 ▄▄██ ██▄▄ Kernel: 6.6.0-rc1-edge-rockchip-rk3588 ▄▄██ ███████████ ██▄▄ Uptime: 4 mins ▄▄██ ██ ██ ██▄▄ Packages: 427 (dpkg) ▄▄██ ██ ██ ██▄▄ Shell: bash 5.2.15 ▄▄██ ██ ██ ██▄▄ Terminal: /dev/pts/0 ▄▄██ █████████████ ██▄▄ CPU: (8) @ 1.800GHz ▄▄██ ██ ██ ██▄▄ Memory: 196MiB / 15718MiB ▄▄██ ██ ██ ██▄▄ ▄▄██ …

I'm using ffmpeg and Kodi from the @amazingfate ppa. All has been running great although I don't think that I'm using hardware acceleration. I'm still on an older Jammy with the old/legacy kernel. I've tried newer kernels but getting issues so I stuck with the older kernel. I've started noticing lately that videos are being encoded with pixel format yuv420p10le. In Kodi, I was getting black screens while the audio was playing. I was following up on the Kodi forums, and was told that Kodi needed to be compiled for OpenGL instead of OpenGLES to make the video render properly. This is the thread: https://forum.kodi.tv/showthread.php?tid=379167 …

I finally got wifi working on a fresh install of 24.5.1. Video acceleration is working perfectly in Chromium but I am not having any luck playing h264 mp4 videos with hardware acceleration in vlc or mpv. Is this possible or am I missing something? CPU is around ~30% with chromium playing 4k youtube but if I play one of my mp4 files it's a solid 130%

Hello I'm running the NAS on Orange PI 5. I've run Armbian with EDK2 from https://github.com/armbian/build/pull/5900. The system starts from SSD disk connected via PCIE card with 4 SATA ports. I wanted to run simple fan control via GPIO, but setting the value 1 or 0 on GPIO has no effect and the multimeter connected to GPIO always shows 2.85V. How I did it. I installed wiringOP as the manual says. I selected GPIO 0 and entered the commands gpio mode 0 out gpio write 0 0 I connected a multimeter to GPIO 0 but it always shows 2.85V when I did gpio write 0 1 the multimeter also shows 2.85V gpio readall shows 1 in column V when "gpio write 0 1" com…

Standard install - Armbian Bookworm, full 'firmware install'. I am getting some packet loss over the LAN. A raspberry pi, Synology NAS and Deban x86 install on the same LAN do not seem to exhibit the same loss. Anyone have experience or ideas? Oddly enough this never seems to occur on fresh installs. This is a docker host for pihole and home assistance, no other packages are really installed at all. I've not really tried much, but since this is a standard install, apt-get update & upgrade are about the only modifications outside of docker install that has occurred. 1. This plugs directly in to a Ubiquiti switch 2. I have tried a few differ…

Hello, I cloned the master branch of WiringOP one month ago, it reported same version 2.46 and it was working except for the option to activate internal pull up/down. Trying it in C code using: pullUpDnControl(n, PUD_DOWN); or by terminal with: gpio mode 1 down same behavior, nothing happen.. by default, unfortunately in my case, it seem active a pull up resistor for all inputs. I searched on the web and found there was a bug, fixed. I checked again the main branch and in effect it is different now, the new code is: *(gpio + GPPUD) = pud & 3 ; delayMicroseconds (5) ; *(gpio + gpioToPUDCLK [pin]) = 1 <&…

Hello, I am running Armbian 23.05 "minimal" (with the provided kernel 5.10.110) on my OrangePI 5 4GB. Upgraded all packets to latest. When trying to run GeekBench 5.5.1 ARM Preview, it reboots when approaching the end of multicore tests, with "performance" governor and default speed range (0.4 - 2.4 GHz for A76). Same goes if I drop the max clock speed to 2.2 for A76. After dropping to 2.0 GHz max, it runs fine; but this hurts performances quite a bit. I tried various power sources, including a bench PSU which can reliably supply up to 30A (but I only see a few spikes over 2A). The board has a large heatsink installed wit…

If anyone is looking at fixing the access for gpio and i2c - I found you can fix it with the following udev rules addgroup --system i2c addgroup --system gpio create in /etc/udev/rules.d/60-i2c-tools.rules SUBSYSTEM=="i2c-dev",KERNEL=="i2c*", GROUP="i2c", MODE="0660" create in /etc/udev/rules.d/61-gpio-tools.rules SUBSYSTEM=="gpio",KERNEL=="gpiochip*", GROUP="gpio", MODE="0660"

In the most recent builds, the kernel logs have been flood with Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x8…

pi@opi5:~/AoC-2023-cplusplus$ lscpu --all --extended CPU SOCKET CORE L1d:L1i:L2:L3 ONLINE MAXMHZ MINMHZ MHZ 0 0 0 0:0:0:0 yes 1800.0000 408.0000 1800.0000 1 0 1 1:1:1:0 yes 1800.0000 408.0000 1800.0000 2 0 2 2:2:2:0 yes 1800.0000 408.0000 1800.0000 3 0 3 3:3:3:0 yes 1800.0000 408.0000 1800.0000 4 0 0 4:4:4:0 yes 2256.0000 408.0000 2256.0000 5 0 1 5:5:5:0 yes 2256.0000 408.0000 2256.0000 6 1 2 6:6:6:0 yes 2304.0000 408.0000 2304.0000 7 1 3 7:7:7:0 yes 2304.0000 408.0000 2304.0000 Why the odd cortex a76 MAXMHZ …

root@orangepi5:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 223.6G 0 disk ├─sda1 8:1 0 256M 0 part /boot └─sda2 8:2 0 221.1G 0 part /var/log.hdd / mtdblock0 31:0 0 16M 0 disk mmcblk1 179:0 0 29.8G 0 disk ├─mmcblk1p1 179:1 0 256M 0 part └─mmcblk1p2 179:2 0 29.2G 0 part zram0 254:0 0 7.7G 0 disk [SWAP] zram1 254:1 0 50M 0 disk /var/log root@orangepi5:~# cat /boot/armbianEnv.txt verbosity=1 bootlogo=false overlay_prefix=rockchip-rk3588 overlays=orangepi-5-sata fdtfile=rockchip/rk3588s-orangepi-5.dtb r…

Ubuntu Noble had some early day issues with default key ring not being stored properly and or synced to the logged in user and users getting popup prompts about the default keyring locked. A week ago I downloaded Armbian Noble 25.5.2 desktop onto my OPi5. It has been my daily driver for the past week or so. It has been a really nice release for my OPi5. All has been good except the default keyring popups. I have created new users, deleted stored keyrings, changed passwords among other things. At this point I am able to store the default keyring password (which is the same as my login PW). However, when launching chromium, and ProtonVP…

For a fresh install of the latest desktop version for OrangePi5 I cannot get the system to run from NVME which is a Samsung 960 Pro. It gets stuck on the spinner at boot for the first-time boot after NVME using SD - NVME in armbian-installer. Any suggestions...

Hi all, I'm trying to debug a sporadic problem with my Orange Pi 5 (16GB) which I'm unable to reproduce. I'm hoping maybe someone else experienced a similar issue or at least has any pointers on how to debug it further. The problem: At random times of the day, the board just appears to freeze up. All communications stop. Board is powered on, with red LED on and green LED off. I have to manually unplug the device to reset it. Within the last 2 weeks, this happened 3 times already. Each time, the last log appears to be a journalctl flush (example: https://pastebin.com/dDm5Xtis - the board froze at midnight, no more logs until …

Hello everyone, I use my Orange Pi 5 board to run Open Media Vault with Wireguard installed. But there is a known issue with Wireguard that, when installing it, you have to manually reinstall the correct kernel into the board again, otherwise it won't be able to boot. However, ever since it has been installed, during apt update / apt ugrade of my board, it keeps recognizing the wrong kernel to be updated and changing the symlinks inside the /boot/ folder, rendering the board unbootable. If I see this happening, I can change the symlinks and it works normally after that. However, sometimes the symlinks changes unnoticed and I cannot boot anymore. I…

Good day, I have Opi 5 and bought this display https://www.aliexpress.com/item/1005005641383181.html?src=google&aff_fcid=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&aff_fsk=UneMJZVf&aff_platform=aaf&sk=UneMJZVf&aff_trace_key=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&terminal_id=b834b596955b44a1bf643629f5ba5647&afSmartRedirect=y . It was a blind buy ... And now I can't get it work if its even possible. I'm its my first time trying to get display on these boards usually use them trought Monitor or TV and it works flawlessly. Cant find even config.txt . But now im lost at how to get …

We have tried to connect the MIPI DSI 10.1 inch OPI Display. It is working fine alone but when we tried to connect another display with the HDMI. we expect it to work as our 2nd display but it did'nt work unless i disable the MIPI display from the OPI Config.

There is no Orange Pi 5 results yet, but we can see already results of RK3588S. https://github.com/ThomasKaiser/sbc-bench/blob/master/results/Sorted-Results.md

I thought I had read that someone had the T2U working out of the box. Well, it's mostly there. When I tried it, didn't work. Got message in dmesg that firmware file not found. Did a Google search and found that it came down to the mediatek firmware files needing to be in the /lib/firmware/mediatek directory but they are currently in the /lib/firmware directory. FYI, the /lib/firmware/mediatek directory already existed and did not need to be created. Also in the current Jammy Gnome desktop Armbian, the file that was being loaded, mt7610e.bin, was not there and only the backup file, mt7610u.bin, was there in the /lib/firmware directory. What I d…

The armbian can't support the third usb bus with pi5.But the official system debian runs normal to support the third usb bus.How to solve the problem?

Hi, I have the board connected by HDMI to a TV but when I start I have no sound, I have to go to the speaker icon, configuration and the option is always selected "Speakers - internal audio" but if I want to have sound I have to choose the output option "Analogic ouput- internal audio" and if I restart I have to do the process again. According to the fine adjustment guide of ARMBIAN I must execute the command pacmd list-sinks | less And should be marked with * the selected card but none appears with that symbol. I attach the terminal output after selecting the right output on the desktop to have sound to see if someone is so kind to help me solve my problem. Thanks a…

Just interested if anyway has being able to set this up in Armbian yet? I had a brief look this morning but couldn't get it to work.

Hello, I have installed the minimal Trixie based image for Orange Pi5 (the image named Armbian_26.2.1_Orangepi5_trixie_current_6.18.8_minimal) and then attempted to build an out-of-tree kernel module. Having installed dkms and build-essentials, plus the kernel headers through armbian-config, I found the headers package hasn't been fully set-up, the build symlink in /lib/modules/<KVER> is missing and dkms complains that the kernel headers for the kernel are not installed. The kernel headers are installed though, but it looks like they're from a previous release (25.11.2 instead of 26.2.1). # dpkg -l | grep rockchip ii linux-dtb-cur…

I've setup the pwm overlay but while it shows up the pwm devices in /devices - it is missing the pwm0 control I've read couple posts where ppl have been able to override the overlays by decompiling the original one, but I can't make sense of the dtc dtb dtbo and dtsi files 😕 Any guides or other suggestions to fix the pwm control? Temperature and fan control on OPI5 - Orange Pi 5 / 5B / 5 Plus - Armbian Community Forums Rock Pi4 pwm control - no overlay? - Rockchip - Armbian Community Forums

Hi, SD card did not load Armbian_25.8.1_Orangepi5_trixie_current_6.12.41_xfce_desktop. I noticed that in boot.cmd line 9 , rootdev is defined as /dev/mmcblk0p1. Should that be /dev/mmcblk0n1 or /dev/mmcblk0n1p1? I note that this file should not be edited and the armbianEnv.txt only refers to rootdev=UUID=7e27c862-0a39-41cd-891e-7d77ff7968fd. Is this an error or am I off course? If so where do I correct it? cheers

With the vendor kernel, my logs are getting flooded with drm error messages Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:r…

Hello, I have a problem with mounting a USB HD via fstab. If I enter the HD in the fstab, the system hangs when booting. The problem, USB is not activated yet and will be loaded later. If I remove the HD from fstab, it is automatically mounted under /run/media/USER. However, this must not be mounted under a user, but should be mounted as root. What can I do. Thanks very much

Orange pi 5 (i dont find way hot to make it in orange pi 5 section) English is not my native, i hope you understand and sorry for mistakes I spend like 3 days on this problem and i think i am stuck I tested offisial image and Josua and there i can use my wifi normally Setup orange pi 5 v1.3.2 clened spi (i got problem like here) armbian 26.5.1 vendor 6.1.115 (from armbian imager on windows) sandisk extreme 64gb sd card after boot i runs sudo apt update sudo apt upgrade -y armbian-config (choose orange pi 5 ap6275p overlay) /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both e…

when I switch to static IP, there is no a connection to default gateway. but when using DHCP everything works fine. $ ip route default via 192.168.88.1 dev end1 proto static metric 100 169.254.0.0/16 dev end1 scope link metric 1000 192.168.88.0/24 dev end1 proto kernel scope link src 192.168.88.32 metric 100 $ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 2: end1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 …

Hello all! In Orange Pi OS latest image all works well EXCEPT it keeps launching apps in a stupid bordered window that has a huge obnoxious bar at the top with 2 absolutely useless buttons, a window to full screen option and the X button How do I hide this stupid thing? It's blocking the whole top of my screen and cutting off part of my TiviMate Pic here https://imgur.com/a/8uo8WrM

Been trying to enable multiple overlays on kernel 6.12 (orange pi 5) but I am not able to get any pwm device in /sys/class/pwm/ The i2c also seems to be missing. Is going back to 6.1 the safest option? Thanks

Hi guys, Would someone point me to where to get a particular distro, mainly looking for jammy_legacy_gnome-amazingfated_desktop for OPi 5 Pro ? I have jammy_legacy_5.10.160_gnome-amazingfated_desktop for Pi5 and Pi5 Plus but it does not work on the Pro version. thank you in advance.

Hi, I've trouble getting 3840x2160 resolution to work. When I try to switch to that resolution the monitor says resolution is 3848x2160 and display is all garbled. 2560x1440 works fine. Also, If I try to login to Gnome (Wayland) I get blank screen and I'm back at the login screen. X11 lets me login to the system. uname -a: Linux lindon 5.10.110-rockchip-rk3588 #trunk.0184 SMP Fri Jan 20 18:24:04 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux I've fetched the latest updates (apt update && apt upgrade) and I've just ran firmware update using armbian-config. Edit: display is connected via usb-c - - > displayport cable.

I have the latest armbian 6.1.75-vendor-rk35xx (ubuntu with gnome desktop) installed and everything works perfectly except that some videos are hanging in chromium. In dmesg I get [23230.260311] [drm:rockchip_vop2_mod_supported] *ERROR* Esmart0-win0 unsupported format modifier 0x800000000000351 and then boom, the whole thing stops playing and hangs. No other error anywhere. This happens with specific mp4 videos on specific frames. Any suggestions?

404 when trying to download SHA on this link:

Hello, finally I have time to play with my OPI5, first thing I tried is to install on USB-C, but the port doesn't seem to work. Then I tried to install using USB3 port, on a ssd drive. The armbian-install utility seems to do the job and after installing the bootloader on mtdblock0 I powered off. At reboot everything is like before: if I remove the sd card the systen won't boot. If I boot with the sd card inserted the root partition is on /dev/mmcblk0p2 First thing that came into my mind is to mount SPI and check if bootloader is ok, but I'm unable to mount it: ~# mount /dev/mtdblock0 /mnt/spi mount: /mnt/spi: wrong fs type, bad optio…

I installed U-Boot in the Orange Pi 5's SPI memory, connected via UART via the CH340G adapter (the power switch is lost). The speed is 1500,000 baud, 8n1. Connected TX-RX, RX-TX, GND-GND. After starting the board, I see the logs, but I can't enter anything at all. When I change the power supply, the input works, but it enters incomprehensible characters instead of the usual ones. When installing the EDK2-RK3588, there was no such problem on the same power supply and adapter. How can I fix the UART input?

*UPDATED - The issue is the powered USB3 hub which is actually NOT USB3 as advertised and is instead USB2. Sorry to have wasted your time* Hi, I have a 1TB SATA SSD in a USB3 enclosure (that supports UASP) connected to a USB3 powered hub, which in turn connects to the Top USB3 port of an Orange Pi 5 4GB. Armbian (Debian Bookworm) is installed and running from a 128GB NVME drive plugged into the M2 slot of the Orange Pi 5. If I do an "lsusb -t" I get the output shown below. The SSD is Bus 02, Port 3, Dev 5 and is using the uas driver but is showing USB2 speed of 480M rather than USB3 speed of 5000M. I have also tried pluggi…

I was running on Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop. For the most part, it worked but the mouse cursor would randomly disappear while remaining functional but invisible. I tried to upgrade using apt-get update and apt-get full-upgrade and after a reboot, it now just displays a flashing underscore. I can SSH into the OS so it's partially functional. Shows as Armbian 23.02.2 Jammy with Linux 5.10.110-rockchip-rk3588 Contents of boot.log: ------------ Mon Feb 27 07:24:15 PST 2023 ------------ done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running…

Been trying to play 4k youtube videos with VLC and I haven't had any luck with vp09 and mp4 files. Is VP9 supported with 24.2.1 + kernel 5.10.160? I have no issues with hardware decoding of mp4/h264 in vlc but is vp9 hardware decoding possible? Browser seems to play youtube in 4k but not sure which codec it is using

My orange pi 5 armbian Os isn’t displaying hdmi output to my monitor. However, it works on my flat screen tv, any reason why this might be ?

Hi, I have orange pi 5. I searched all over internet for information how to set on startup/power on GPIO pins behavior, but i cannot find anything. Most of GPIO pins are set to IN mode 1. Sadly I need them to output mode 1. I am scared something could burn this way since i set them to though wiringPI after kernel boot sequence is complete. Can some one give information how I can set them up at earlier point when I power on the board? I found that DTB/DTS file could do it. But there is no clear information / pin addresses I should set. Thanks in advance! Regards!

I had some difficulties to make my sata disk work and found out that the regulator had to be switched on. So here a dtbo and source to make it hopefully a bit easier for some others. Easiest way to install is "sudo armbian-add-overlay orangepi-5-sata.dts" orangepi-5-sata.dtbo orangepi-5-sata.dts

Hello! Has anyone tried to play straight unconverted hevc video from a GoPro 11? Iv'e tried ffplay and gst-play but I'm just getting a static image and a bunch of these errors, [swscaler @ 0x7f49d399c0] [swscaler @ 0x7f49d47a50] deprecated pixel format used, make sure you did set range correctly I have successfully played example jellyfish videos of hevc and hevc 10bit formats, ffmpeg reports the following details from the GoPro footage, Stream #0:0[0x1](eng): Video: hevc (Main) (hvc1 / 0x31637668), yuvj420p(pc, bt709), 3840x2160 [SAR 1:1 DAR 16:9], 119725 kb/s, 119.88 fps, 119.88 tbr, 120k tbn (default) …

Hello friends: I have opi5 with the spi removed, which spiloader do I use to boot from the sd card? Thank you so much

as the title says i used latest build of armbian cinamon for opi5 and i am tryin to set thing up but chromium is basicaly useless since its reset everytime its closed. i had older armbian build on ssd and after few updates chromium started doing same thing so i guess its not the armbian but some fail within chromium? anyone knows whats wrong with it or how to fix it? so what i mean by useless is it doesnt remeber any logins or passwords so if i open it 100 times i have to login 100 times. thanks for any help

Only sharing what I managed to make working on the Orange Pi5: a Tvheadend server with satellite cards TBS 5527 and TBS 5520se. The rough path I followed: - recompiled the kernel in order to have "Linux tv" as a module (CCONFIG_DVB_CORE=m). This will be replaced by the tbs driver in next steps. - installed TVheadend from the armbian-config - compiled tbs drivers by following standards instructions....but: - had to add a CFGLAGS += -w to avoid some warning stopping the build (Makefile in the v4l directory) - had to disable the creation of the mc.ko (MEDIA_CONTROL) to avoid conflict with kernel built-in module (n…

See for more details but without using the overlay-user folder - I was not able to get the pwm to work on a fresh download.

I built apt packages for the OPI 5 wiring pi and have them hosted in lauchpad https://launchpad.net/~erik1220/+archive/ubuntu/wiringpi-opi Any way to contribute them to the official build? Btw apt-add-repository is broken on 25.8 - I assume it is a side effect of python 3.11... seen similar errors on ubuntu

Expected behavior: rastered content is smooth like so: Observed behavior: rasterization is very pixelated: Workaround: go to about:flags and change #enable-gpu-rasterization to disabled, however this makes sites such as geogebra.org/calculator run very slow.

I am attempting to install the file Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop.img from https://www.armbian.com/orangepi-5/ but the installation hangs at the point where the root password should be entered. The same happens with the file Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_minimal.img. If i use the file Armbian_22.11.3_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop.img from the Github archive the installation completes. I have tried to raise a bug but the only solution for not booting are hardware and the installation has not progressed far enough to enter any commands. Any assistance welcomed.

I have my kernel locked to 6.1.75 but still after 25.8.2 update, I lost all USB devices on both of my Orange PI 5. Only the USB3 port is working. The only way I've been able to get access to the USB is by switching to the latest `current` kernel... Any clues on what is going on? Firmware or kernel upgrades are not doing anything... where can the issue be???? I tried downgrading to many different versions but beside the current branch, USB is gone. Thanks

After upgrading to kernel 6.8, I've noticed my orange pi 5 running a bit hotter than when using kernel 5.10, even with the CPU load a little bit lower than before. Nothing alarming, just an observation. Did anyone else notice the same behaviour?

I only have options 1,4,5,7 on my nand-sata-install utility and can only boot from a single armbian microsd card but no other. /dev/mtdblock0 shows no files. Everything has been fine till now! Would love some help. Thanks

Hi, what is the appropriate way to upgrade from the earlier 23.5.1 to the latest 23.5.5 on the orange pi 5? Thanks

Hello people, Happily running Bookworm, because it was the mainstream download for OPI5 a few months ago, I now see that the main download for OPI is back to Jammy. Apart from hardware accceleration, Bookworm runs great for me. In fact HA is not crucial for my server usage, though it would be nice. Question: what is the reason the main OPI5 download is now back to Jammy in stead of Bookworm? And what would be the advantages of going back from Bookworm to Jammy? (Got the aluminium passively cooling case for the OPI5, so far it's been great, 10 minutes of stresstesting all 8 cores doesn't get above 70 degrees celsius. For reference my…

I recently added a monitor to my server as there were issues and I wanted to see logs directly on the OPi5. The monitor is part of the Motorola HD Dock. I'm using it for it's keyboard and monitor. In any case, the following messages appear in DMESG and keeps repeating ever second or two: [522074.762209] vop2_isr: 107217 callbacks suppressed [522074.762239] rockchip-vop2 fdd90000.vop: [drm:vop2_isr] *ERROR* POST_BUF_EMPTY irq err at vp0 [522074.762321] rockchip-vop2 fdd90000.vop: [drm:vop2_isr] *ERROR* POST_BUF_EMPTY irq err at vp0 [522074.762359] rockchip-vop2 fdd90000.vop: [drm:vop2_isr] *ERROR* POST_BUF_EMPTY irq err at vp0 [522074.762400] rockch…

Hello! I installed the latest Gnome Noble image from the very top of the Orange Pi 5 page, it has Wayland and generally is working really well - it even is doing higher refresh rate for my monitor and is smooth! HOWEVER the one big thing I noticed right away - my screen never turns off anymore And my Power options are missing such settings? It only gives the option to blank, which still is running my monitor at 100% brightness and a horrible solution Where is the setting to turn my screen off after 5 minutes? NOT blank, but into standby mode Worked on the previous Cinnamon version but that version lacked higher refresh rates and I think…

booted opi5 via nvme one day and the boot screen mentions about btrfs partition missing even tho it was using ext4 partition. booted via sdcard and the root partition is entirely missing on the nvme. the boot partition is still there and working. not sure if relevant but the previous time i shut the opi5 down, i forgot to unplug it and it was plugged in for about an hour after shutdown with the red led and fan on. the nvme is kingspec which while cheap doesnt seem to have that many bad reports online that i can find (the boot partition was fine so i suspect kingspec isnt at fault). the power adapter is a 25w phone charger w/ pd/qs; it hasnt exhibited any weird behavior (l…

For some odd unknown reason. I can not get the following installed and running. (using official os for Opi5) 1- A virtual machine running on armbian. 2- Dolphin emu 3- Waydroid Thx, vandyman

Hi Ive just installed the latest version of Armbian (Ubuntu Noble+KDE) and everything works fine except it looks like it is not detecting my TV resolution correctly. I can choose 1920x1080@120hz but if I try yo go to 4K I can only select 24Hz I attach armbian monitor logs url, modetest and kscreendoctor My cable is HDMI 2.1 Any help would be appreciated modetest -c trying to open device '/dev/dri/card1'... is not a KMS device trying to open device '/dev/dri/card0'... done opened device `RockChip Soc DRM` on driver `rockchip` (version 1.0.0 at 0) Connectors: id encoder status name size (mm) …

``` May 21 21:53:26 rpc.idmapd[21345]: main: fcntl(/run/rpc_pipefs/nfs): Invalid argument May 21 21:53:26 systemd[1]: nfs-idmapd.service: Control process exited, code=exited, status=1/FAILURE ``` The rpc.idmapd version in Debian is still ancient (as with many things in debian) and still requires dnotify but the armbian kernel for the orange pi 5 build ``` $ grep -i dnotify /boot/config-5.10.110-rockchip-rk3588 # CONFIG_DNOTIFY is not set ``` It looks like bookworm will likely fix this when it's out, so maybe the right thing to do is simply move to bookworm asap but this does prevent the ability to fully support nfsv4 with…

Hi all, Is anyone here good with upbringing MIPI panels on Linux via device tree modifications? I've had an attempt with a specific LCD panel but I am not having any luck to be honest. I would love someone to kindly review my Git Diff/device tree changes for any errors. I've attached my LCD init code as well, as well as the DSI portion of the dmesg output log, as well as my schematics for the custom driver board I have designed. https://drive.google.com/file/d/18E5zOGlNpdWLrD43R7bB4N-Mf_8mQFKY/view Thank you! DSI_Debug_Log.txt

I have an Orange Pi 5 running Armbian Noble and I need a distribution that supports USB OTG in peripheral mode and supports dcw3_generic kernel module. I've tried to compile one with support, but I keep getting: modprobe: FATAL: Module dwc3_generic not found in directory /lib/modules/6.1.115-vendor-rk35xx I triple checked .config and the appropriate flags are set to Y. I am trying to get the Pi to act as a mouse attached to another machine's USB port. Any help is greatly appreciated.

I have edge kernel installed and working. I compiled the v4l2 ffmpeg but some of my av1 videos are not working. After some digging I noticed that v4l2-ctl --device=/dev/video4 --list-formats-ext ioctl: VIDIOC_ENUM_FMT Type: Video Capture Multiplanar [0]: 'VT12' (Y/UV 4:2:0 (4x4 Linear)) [1]: 'NV12' (Y/UV 4:2:0) Shouldn't this include the 10 bit formats as well? (NV15?) Does anyone know why the 10 bit format is missing in the kernel? Is this specific to the orange pi? I found this GitHub - dongioia/rock5bplus-rkvdec2: Rock 5B+ (RK3588) on mainline Linux 7.1: V4L2 stateless RKVDEC2/Hantro hardware video decode (…

Greetings, I have an Orange Pi 5 with the edk2 1.1 UEFI bios on the SPI, and an NVMe installed. The BIOS has been set to "Mainline" in the device tree option I tried visiting here https://armbian.com/boards/uefi-arm64 and burning the minimal current6.18.8 CLI image to my USB stick. The Orange Pi 5 displays the graphical grub menu with no problems, complete with penguin in the background etc, but once I choose the boot Armbian option, it displays a few lines of terminal output and then the monitor goes black as if the GPU is initializing and a desktop or graphic would be about to show - when instead, the monitor just reports no signal instead. The system isn't…

Needed/wanted to add Bluetooth to my OPi5 and also needed WiFi at the same time. Did not want to use 2 USB ports so I tried the T2UB. Working well. Bluetooth appeared on my Armbian Ubuntu Jammy setup and I plugged in the dongle. It saw a few of my bluetooth devices. Reason I wanted bluetooth is to use a controller for some games/emulators. I'll make another post for that. My PS4 Dualshock controller is not showing up in the list of devices. My version is an older version, Armbian 23.06.420 Jammy with Linux 5.10.160-rk35xx No end-user support: built from trunk Conclusion: TPLink T2UB should work properly on Armbian Ubuntu desktop.

Has anyone found a working gpiolib implementation for Armbian on Orange Pi 5? I'm aware of wiringPi and it sort of works. However, being able to use the "real stuff" so to speak would make my life easier.

Has anyone successfully set up a MIPI screen with their LCD ribbon connectors on Armbian? Any wisdom from someone who has done this would be appreciated.

I download the following image and encountered serious problem; Armbian_23.8.1_Orangepi5_bookworm_legacy_5.10.160_cinnamon_desktop.img.xz The problem is that after screen blank out, 8 CPU cores get near full 100% usage and OPi5 gets very hot. They all have the following htop profile. Pri NI VIRT SHR S CPU% Command 20 0 5725M 224M R 96% cinnamon -- replace

Got quite excited seen that the wifi driver is finally available and was going to test the browser and graphic acceleration in the current kernel but I flashed 3 times the Desktop image with Gnome/Current 6.18.33 and it did not boot. Is there possibly an issue with u-boot?

Inspired by Bazzite OS, and remind me of experience on Armbian (not just armbian), basically on Orange PI 5/ OPI5+, it'll be solid OS if update failure/ anything went wrong can rollback to previous safe copy. Pain-point: I just want to use the system, not keep re-flashing OS. nixOS is good, but I don't want to re-learn everything ... and giving up my Ubuntu eco-system. Sorry I'm still testing out, and failing with existing Armbian-Config approach, I'm trying my own appraoch, Iknew the rules here, wait until I success I'll share it here. (note: or anyone did it before, can give me some direction) Inspired by Bazzite OS, and remind me of experienc…

Ok I wasnt going to say But Sandi, says Prove The Shit. Who Is Wrong.... nyanmisaka left a comment (jellyfin/jellyfin-ffmpeg#765) I am unable to reproduce the issue. jellyfin-ffmpeg is intended solely for use with the Jellyfin server. If the custom version of our MPP dependency is causing your specific problem, please build your own version using the upstream MPP. Additionally, you completely ignored the issue report template. — Reply to this email directly, view it on GitHub, or unsubscribe. Triage notifications, keep track of coding agent tasks and review pull requests on the go with GitHub Mobile for iOS and Android. Download it today! You are receiving this because …

Hi all! I'd like to share a small personal project that I've been working on recently for the Orange Pi 5 (and potentially other RK3588 boards). Like many RK3588 users, I wanted to run Kodi on a modern mainline Linux kernel instead of relying on older vendor kernels. After a lot of testing, debugging and learning, this project started to take shape, and I've a stable almost "all works" setup Tested on Armbian (minimal Debian and Ubuntu 24.04) with mainline kernel Not working: -HDR -Maybe some network services Next up: -Wayland support -Audio visualisers https://github.com/Danibos/mainline-…

orangepi5-max:~:% sudo apt upgrade -y Upgrading: armbian-bsp-cli-orangepi5-max-edge bsdutils fdisk libbz2-1.0 libmysqlclient24 libudisks2-0 linux-u-boot-orangepi5-max-edge rfkill zlib1g-dev armbian-firmware bzip2 gnu-coreutils libfdisk1 libsmartcols1 libuuid1 login udisks2 armbian-plymouth-theme diffutils libattr1 libminizip1t64 libssh-4 linux-dtb-edge-rockchip64 mount util-linux base-files eject …