Orange Pi 5 Plus

Hi, I was just trying to test locally build image with edge kernel (Armbian_23.11.0-trunk_Orangepi5-plus_bookworm_edge_6.6.0-rc1.img) by flashing it on SD card and then trying to boot off it in my Orange Pi 5+. The board just sits there with the LED blinking and that's it. The legacy kernel image (Armbian_23.11.0-trunk_Orangepi5-plus_bookworm_legacy_5.10.160.img) boots fine. Do I have to carry out some extra step(s) to test the edge kernel? It's not a show-stopper for me as I have legacy image booting of EMMC nicely (and I am running jellyfin in docker happily there). It's just I thought I might test out some bleeding-edge s…

I have tried to download at least 3 times this image: Armbian_25.8.1_Orangepi5-plus_noble_vendor_6.1.115_gnome_desktop.img.xz All sha256sum verified Ok. And wrote 5 times on 3 different SDCards, and this img does not boot on my OPI-5-Plus. No image on monitor, partition armbi_root not expanded, no green lights... Just unusable (for me). Other img's that boot are OK: Deb-xfce, noble-cinnamon, noble-neon... Someone got success with this img??? I'm looking for a distro that works well on OPI5-Plus, well configured, and that works with HDMI audio. The best for now is Noble-Cinnamo…

Hello everyone, and Happy New Year. One question about Orange Pi 5 Plus: i have installed a wifi module (supported than what the official Orange documentation reports) AX210NGW in my Orange Pi 5 Plus main board with Operating System: Armbian 23.11.1 bookworm and Kernel: Linux 5.10.160-legacy-rk35xx. I copied in /lib/firmware the firmware of the module (https://intel.ly/3S0QZrA). if from the terminal I run: lspci I see the device but in "Armbian-config" in hardware section don't see the wifi module, and I can't activate the module to surf the Internet or the local network in wifi. The question is: am I forgetting any steps to setup the wifi module cor…

Is there an Armbian image with home assistant that isn't minimalistic? or Is there a way to install HA on a more robust desktop armbian 25.2 image for the Orange Pi 5 Plus? I feel the orange pi 5 is robust enough to handle HA under a desktop Armbian environment than other SBCs.

How do I change the default desktop environment on Debian 12 startup from cinnamon to xfce4? I have installed xfce4 and it's related "goodies", added a .Xclients file containing "startxfc4" in both root and ~/ folder locations. But the unit sometimes boots back into cinnamon. I do not see anything under armbian-config to control the desktop environment or to switch between cli/gui. I recall such options under orangepi-config (at least the cli/gui switching).

I've found information on how to use your own IR remote controller from this site: https://forum.odroid.com/viewtopic.php?f=215&t=44671 In short: 1. Enable logging from the IR kernel module, enter in a terminal: sudo -i echo 1 > /sys/module/rockchip_pwm_remotectl/parameters/code_print dmesg -w 2. Check if your remote is supported by pressing the keys on your remote. It should give you info like: [ 3485.342354] USERCODE=0xfb04 [ 3485.369309] RMC_GETDATA=fd 3. Download the overlay file below and edit the usercode and the code for each key. So for like with the key above it'll be 0xfd 4. Place the header f…

the issue is as follows: 1. When using the Type-C interface to connect to an external monitor, the display works normally if the monitor is connected after the development board has started. 2. If the monitor is disconnected and then reconnected after approximately several hours (possibly more than 6 hours), the display fails to show any image. I used the `armbianmonitor -u` command, and it output the following URL. https://paste.armbian.com/foyecusoju If the Type-C interface is functioning normally, the latest output from `dmesg -w` would show the following: [ 1155.922647] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller [ 1155.922692]…

I will receive soon a Orange Pi 5 Plus. I have setup completely an Orange PI5 with Armbian. I had to recompile kernel, compile drivers ...... it took some time. If I run the Orange PI5 plus with the same SD card as the Orange Pi 5, would it work? If not, is there an easy thing to do to make it work? I think there is a device tree file hardware specific , but is it read when compiling the kernel or dynamically? I am asking because processors are very similar, and it would make my life easier! Your view will be appreciated. Thanks.

Hello, I tried to install the RTL8821CE card on Orange Pi 5 Plus, but only the Bluetooth is on, the wifi not working. Which driver i should use? I am using Armbian 24.2.1 Jammy with Linux 5.10.160-legacy-rk35xx here is the dmesg of admin@orangepi5-plus:~$ nmtui admin@orangepi5-plus:~$ dmesg | grep 8821 [ 5.588211] pci_bus 0003:30: root bus resource [mem 0x9c0000000-0x9ffffffff pref] [ 8.482106] rtw_8821ce 0002:21:00.0: enabling device (0000 -> 0003) [ 8.493940] rtw_8821ce 0002:21:00.0: Firmware version 24.11.0, H2C version 12 [ 8.534600] rtw_8821ce 0002:21:00.0: rfe 6 isn't supported [ 8.534719] rtw_8821ce 0002…

Hi, A UEFI-ARM64 install of armbian opi5+ 24.11.0-trunk fails during armbian-install due to incorrect knowledge of partitions: root@uefi-arm64:/usr/sbin# lsblk -l NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 1 14.4G 0 disk sda1 8:1 1 256M 0 part /boot/efi sda2 8:2 1 14.2G 0 part /var/log.hdd / zram0 252:0 0 7.7G 0 disk [SWAP] zram1 252:1 0 50M 0 disk /var/log zram2 252:2 0 0B 0 disk nvme0n1 259:0 0 953.9G 0 disk nvme0n1p2 259:3 0 953.6G 0 part /mnt/armbian-install.NQULbp/rootfs /mnt/tmp…

Introduction This guide describes a tested method for running Android, Armbian, and Ubuntu on the same NVMe SSD of the Orange Pi 5 Plus. This is not an official Orange Pi installation procedure. The entire workflow was developed through extensive real-world testing. The following configuration has been successfully verified: ✅ Android boots from the NVMe SSD. ✅ Armbian boots from the same NVMe SSD via UEFI. ✅ Ubuntu boots from the same NVMe SSD via UEFI. ✅ All three operating systems coexist on a single NVMe SSD. ✅ Armbian and Ubuntu share the same EFI partition. ✅ Android, Armbian, and Ubuntu can share a common data partition. 1. Requirements Har…

Hi. I have the official raspberry TV hat https://www.raspberrypi.com/documentation/accessories/tv-hat.html I'm wondering if I can use it on the Orange Pi. https://pinout.xyz/pinout/tv_hat http://www.orangepi.org/orangepiwiki/images/a/ac/Plus5-img302.png

HW: OrangePi5 Plus 32 32 GB RAM 512 GB NVME 5K Monitor Image: Armbian_25.8.1_Orangepi5-plus_trixie_vendor_6.1.115_xfce_desktop.img prepare system before each case dd if=u-boot-V2024.04-orangepi5-plus-spi.img of=/dev/mtdblock0 flash_erase /dev/mtd0 0 0 case 1: 1. copy image to 64GB uSD 2. booting 3. system comes up with xfce 4. sudo apt-get -y update; apt-get -y upgrade 5. reboot 6. system comes up, without desktop. system is reachable with ssh case 2: 1. copy image to 64GB uSD 2. booting 3. system comes up with xfce 4. armbian-install 5. choose boot from mtd flash 6. choose nvme0n1p1 6. update mtdbloc…

Hi, I've read on here that you can apparently switch to a stable edge branch through Armbian Config, but the closest I can find is 'switch to rolling packages repository' and 'distribution upgrade to rolling unstable'. Are either of these correct? I'm running the Ubuntu Noble 6.12 kernel, btw. Many thanks.

Hi gals & guys, Came over to this forum from the OPI forums which seem.. rather low on real-user activity. I am quite new to the SBC Arm64 platform and have many questions. I am an experienced sysadmin on x86/amd64 and still figuring out the differences. I bought a Orange Pi 5 Plus 32G of RAM and i am running of the 256G emmc. I am able to run different OS's (OPI-Ubuntu, OPI-debian, plain Ubuntu and Armbian). As i intend to use the board as server i didn't look into Android and the like.. My plan is running (OMV) from the emmc and attaching ZFS storage by means of a nvme-to-sata adapter and providing iscsi storage from there to my home-lab with my VM's …

Hi all, Just want to share this issue i came across from my recently purchased OPI5+ 32GB version. I noticed it freezes when transferring .img from micro SD card to eMMC or NVMe drives via the command line. Now the img file are armbian OS and no its not the img file issue. at times I can get it to around 70seconds and it will freeze. hard reboot is required, unable to complete the transfer. I have also tried to reduce the bs=10 speed but still the same. Now i have also got the 16GB version and this works fine with no issues... Good chance there is something wrong with this latest hardware..…

I've got Orange Pi 5 Plus board with 16 Gb of RAM, 256 Gb of eMMC, Realtek RTL8852BE-CG wireless module. SD card is Samsung EVO Plus 32Gb. I tried to run Armbian images on this board (from the SD-card I've mentioned before) but it was absolutely failed. I tried 5 images: Armbian_23.11.1_Orangepi5-plus_jammy_legacy_5.10.160_gnome-amazingfated_desktop.img.xz Armbian_23.11.1_Orangepi5-plus_bookworm_legacy_5.10.160.img.xz Armbian_23.11.1_Orangepi5_jammy_legacy_5.10.160_gnome-amazingfated_desktop.img.xz Armbian_23.11.1_Orangepi5-plus_bookworm_edge_6.7.0-rc1.img.xz Armbian_23.11.1_Orangepi5-plus_jammy_edge_6.7.0-rc1.img.xz which…

Hey @amazingfate, I have an issue with the build-in IR receiver on my OPI5+: ##O#O## OS: Armbian 25.8.1 noble aarch64 ####### Host: Orange Pi 5 Plus ########### Kernel: 6.1.115-vendor-rk35xx ############# Uptime: 2 mins ############### Packages: 1934 (dpkg), 5 (snap) ################ Shell: bash 5.2.21 ################# Resolution: 3840x2160 ##################### DE: GNOME 46.0 ##################### WM: Mutter ################# WM Theme: Adwaita Theme: Adwaita [GTK2/3] Icons: Adwaita [GTK2/3] …

Board: Orange Pi 5 Plus (RK3588) Armbian image used: Downloaded from https://armbian.cn/boards/orangepi5-plus (Ubuntu 26.04, .img format) Comparison image: Joshua Riek's Ubuntu for Rockchip – https://joshua-riek.github.io/ubuntu-rockchip-download/boards/orangepi-5-plus.html Problem Description I downloaded the Armbian image for Orange Pi 5 Plus from the official Armbian page and flashed it to both a TF card and eMMC. The board fails to boot in either case. However, when I flash Joshua Riek's Ubuntu image using the exact same methods, the board boots successfully without any issues. I have compared the partition layouts of both images and found them to be essenti…

I somewhat recently used Armbian Build to compile a desktop Bookworm image, which is quite stable and functional except for EMMC support. Packages: Debian stable (bookworm) Support: DIY (custom image) Linux Atlas 6.1.84-vendor-rk35xx #1 SMP Tue Dec 24 13:36:04 UTC 2024 aarch64 GNU/Linux My question is where can one find the current status of the various kernel versions support for features like I2C, SPI, EMMC, MESA, etc.? I recognize that newer kernels like 6.12.yyy are very much a WIP. I also would love more information on the the RK3588 kit used with kernels to backport features.

After upgrading to kernel 6.10.1-edge-rockchip-rk3588 I started getting: fdee0000.hdmi_receiver: hdmirx_wait_lock_and_get_timing: HDMI pull out, return on the console. This repeats constantly and quite rapidly, and just doesn't stop. I can silence it by plugging a monitor into HDMI port, but... I prefer to run my board headless (serial + net). Does anybody know any other way to get rid of this? This "feature" was absent with the -rc7 kernel.

Any guidance on getting the native 2-pin fan connector and control working with Armbian Jammy? e.g. using pwm-fan driver to control the fan. Thanks for any help, please be kind, I'm a newbie 🙂

I have some problem starting Linux image with my OPi 5+. I just got an OPi 5+ 16Gb RAM no eMMC. I flashed official Android image into SD card with SDDiskTool following the instruction in wiki. It worked. Then I do the "Data Reset" in Android Settings. The board doesn't boot anymore. I re-flashed Android into the SD, and it worked again. Then, I want to try Linux. I flashed Joshua Riek ubuntu-22.04.3-preinstalled-desktop-arm64-orangepi-5-plus.img.xz into the same SD with balenaEtcher. It doesn't boot. I tried again with Armbian_24.2.1_Orangepi5_jammy_legacy_5.10.160_gnome-amazingfated_desktop.img.xz and official Ubuntu image as well. None of them ma…

Orange Pi 5 plus. It seems that in the 'edge' kernels, ssh is disabled by default. Since HDMI doesn't function this is a problem. I used the debugging UART and after setup I got the message "ssh.service is disabled" I enabled the service and all is well. Any reason why ssh would be disabled?

After installing official Armbian_25.2.1_Orangepi5-plus_bookworm_vendor_6.1.99_xfce_desktop.img to sdcard, then to nvme all is fine, until, I do an apt update & upgrade, after that point chromium fails to run. I explored the logs to see it a failure to load chromium.conf from /etc/chromium.d/chromium.config (failed symbolic link to /etc/armbian/chromium.config). Is there a known workaround besides utilization of firefox?

Hi, I've had my 5+ for a week now and tinker with it when I can. Some things I've noticed... Using Amrbian legacy 5.10 legacy.... the system draws about 2.2w idle using a USB meter and no peripherals attached. When using the trying the latest 24.2.0-trunk.79, the power draw increases to 3w idle. I also noted the LED flickers between green and red rather than blue and red with legacy. My guess is more peripherals are being enabled. When using legacy, the first time i run an apt-get update there are 39 'gets'. When I then added a launchpad ppa and run again I only get 6. Not sure why that is. I cannot get…

Updated: The Armbian vendor kernel version now includes Panthor, and will soon be able to run it as well. Waydroid images: https://github.com/WillzenZou/armbian_fork_build/releases/download/willzen-armbian-24.5.0/2.waydroid-panthorv10-240416-v1.img.tar.gz Note: Waydroid needs to be run in the Wayland desktop environment. (Such as Gnome wayland, KDE wayland session) What's work: OpenGL ES is ok, I have tested some game: Mincecrat, gameSHINE, Monument Valley 2 What's not work: Vulkan. Video hardware decode and encode. How to use Waydroid 1. To install Waydroid,…

##O#O## OS: Armbian 25.8.1 noble aarch64 ####### Host: Orange Pi 5 Plus ########### Kernel: 6.1.115-vendor-rk35xx ############# Uptime: 1 day, 8 hours, 17 mins ############### Packages: 1852 (dpkg), 5 (snap) ################ Shell: bash 5.2.21 ################# Resolution: 3840x2160 ##################### DE: GNOME 46.0 ##################### WM: Mutter ################# WM Theme: Adwaita Theme: Adwaita [GTK2/3] Icons: Adwaita [GTK2/3] Terminal: x-terminal-emul CPU: (8) @ 1.800GHz …

Hi I have been trying to install root file on btrfs using armbian-config from sd card to nvme The process completed successfully but cannot boot. (Note that I have also modified armbianEnv.txt from etx4 to btrfs) The same process works on ext4 Appreciate if someone can give some pointer to get this working

Every time I stop and then start Chromium, do a search on google, or on youtube, there seems to be a deletion of the cookies, and it asks consent again, login again .... I found lots of possible solutions on internet about that issue, but none work for me! I wonder what this is due to, any ideas?

Hi, I've been running Armbian legacy server on my 5+ for a month now. I had trouble initially with my EMMC not booting, but I discovered, I had to wipe the SPI Nor then using Armbian config to flash it, then write to EMMC. When a new version of Armbian comes out for the 5+ and it may be a 6.8 kernel build, will I need to re-flash the SPI before I can install the newer version of Armbian (or another image from that's not Armbian?) before updating the EMMC. I found the steps on the Radxa site insightful for a general overview of SPI Nor and flashing (I understand it not an OPi5 x board), but it's not clear to me if a different OS will ne…

Hardware: OrangePI-5-Plus (rk3588), with "32 GB" of RAM Operating System: Debian Trixie (pure, except EFI boot and Armbian edge kernel) Root File System: Ext4 (encrypted) Desktop: KDE Plasma 6.3.6 (wayland, GDM3), KDE Frameworks version: 6.13.0, QT version: 6.8.2 EFI Source: https://github.com/edk2-porting/edk2-rk3588 The boot messages, after a few starts (spaced apart) of the low-memory-monitor.service, say there's a failure to start it. After booting is complete, here's a screenshot of the output of: systemctl status low-memory-monitor.service This error didn't show up until I installed a number of packages. I tracked down the off…

Hi, The RK3588 supports frequencies as low as 408MHz, but in armbian the minimum is 1008MHz, which makes the cpu run hotter and draw more power even when idle, compared with the OPI ubuntu version. These are the available frequencies: $ cat /sys/devices/system/cpu/cpufreq/policy0/scaling_available_frequencies 1008000 1200000 1416000 1608000 1800000 $ cat /sys/devices/system/cpu/cpufreq/policy6/scaling_available_frequencies 1200000 1416000 1608000 1800000 2016000 2208000 2400000 I want to add the missing frequencies, I tried to look in the armbian repo for dts files that contain these frequencies, but I couldn't find anything. Is is possibl…

Please advise (see low/high values): nvme-pci-0100 Adapter: PCI adapter Sensor 1: +31.9°C (low = -273.1°C, high = +65261.8°C) Sensor 2: +39.9°C (low = -273.1°C, high = +65261.8°C) Sensor 8: +31.9°C (low = -273.1°C, high = +65261.8°C)

I understand that panthor is not supported for wayland but in that case I would expect libmali to fill in... but I ended up with lvmpipe. The overlay along with another recent post led me to believe that panthor was the expected default and libmali was an artifact, but I'm now questioning that after finding a thread identifying use cases where libmali can be preferred and a comment suggesting panthor wouldn't be available until 6.13. As a result, I am now questioning if there is a reason that software acceleration is the default and the user is expected to determine which path they want to go? I know support for the hardware has been slow going so I …

I'm trying to install https://dl.armbian.com/orangepi5-plus/Bookworm_vendor_minimal in my Orange PI 5 Plus to the emmc but I've got a black screen after removing sd card.

Hi everyone! I have recently bought an Orange Pi 5 Plus (16 GB RAM) and installed Armbian (the Pi Plus version). Then I enabled GPU hardware acceleration, as suggested on the Armbian download page, which then updated chromium and other things to the rkmpp versions. Now, if I start chromium under Wayland (tried Sway, Gnome, and KDE), the hardware acceleration works nicely, so I get good FPS on e.g. WebGL aquarium, and similar things. However, the antialiasing of some items on the screen does not seem to be working. Antialiasing in WebGL seems off as well. You can see an example in the attached screenshot. Here's what I have tried so far: Before installing GP…

Hi all! I have a problem with Armbian images on kernel 5.10.160 (jammy & bookworm Armbian_23.11.1_Orangepi5-plus_***_5.10.160.img) When starting from the SD card the nvme device is not visible root@orangepi5-plus:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS mtdblock0 31:0 0 16M 0 disk mmcblk1 179:0 0 58G 0 disk ├─mmcblk1p1 179:1 0 256M 0 part /boot └─mmcblk1p2 179:2 0 57.1G 0 part /var/log.hdd / mmcblk0 179:32 0 233G 0 disk mmcblk0boot0 179:64 0 4M 1 disk mmcblk0boot1 179:96 0 4M 1 disk zram0 254:0 0 7.7G 0 disk [SWAP] zram1 254:1 …

Hello everybody. I own a Orange Pi 5 Plus with Debian and 3 partitions: boot, root and storage (fat, ext4, ext4). Now I want to try Armbian but I don't want to overwrite the storage partition, so I shoudn't use dd to write the .img file. Ant tip to solve this situation? Thanks.

Hi can anyone advise if they have come accross this issue. so somehow HDMIRX seems to be the hdmi input controller starts to freak out for no reason there is nothing plugged into it EVER and will randomly start to outpur this to console im thinking maybe the HDMIRX is faulty and want to remove it, I have tried removing it removed the DTB , decompiled and edited and removed it from DTB, tied to blacklist it but with no effect it does not stop spamming and the device [ 89.603095] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_phy_register_write wait cr write done failed! [ 89.613765] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_phy_register_write wa…

I would love to use Armbian Build to construct a Debian 12 Bookworm images with KDE Plasma as the windows manager. I note that KDE Plasma isn't an option in the armbian builder. I have no problem building with XFCE or Cinnamon.

Installed: Armbian_23.11.1_Orangepi5-plus_bookworm_edge_6.7.0-rc1 The analog device is visible, but there's no sound from the headphone jack. The hdmi device is not visible. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Analog [Analog], device 0: fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0 [fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0] Subdevices: 1/1 Subdevice #0: subdevice #0 There is no sound when I play a test file: aplay -D hw:0,0 /usr/share/sounds/alsa/Noise.wav Playing WAVE '/usr/share/sounds/alsa/Noise.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Mono apl…

Hello, I just got a wifi 7 adapter (QCNCM865) and I was thinking the ath12k driver was available starting from kernel 6.13, I'm running the edge kernel 6.16.4 and the ath12k driver is failing to load and I can't find any wireless drivers in /usr/lib/modules/6.16.4-edge-rockchip64/kernel/net/wireless. Do I need to rebuild the kernel with the ath12k driver? or is there a kernel version available with that driver? Thanks for your help!

Hmm, seems i need someone holding my hand all steps of the way 😇. Soon i'll need to pay some.. 🥰 I got my OPI5plus working from emmc with nvme-to-sata adapter on edge kernel and now i have 5 HDDs and 1 SSD connected to it. Intended for ZFS with cache... But : ZFS module won't build. I installed linux-headers and tried # apt install zfsutils-linux zfs-dkms. --- Setting up zfs-dkms (2.1.9-2ubuntu1) ... Loading new zfs-2.1.9 DKMS files... Building for 6.7.0-rc1-edge-rockchip-rk3588 Building initial module for 6.7.0-rc1-edge-rockchip-rk3588 configure: error: *** None of the expected "bops->release()" interfaces were detected. …

Hello Developers, I ran into some issues installing the latest release on an Orange Pi 5 Plus. The images I downloaded are as follows: Armbian_24.11.2_Orangepi5-plus_noble_current_6.12.0_kde-neon-kisak_desktop.img.xz Armbian_24.11.2_Orangepi5-plus_noble_vendor_6.1.75_gnome-kisak_desktop.img.xz The KDE version will install and boot from the 256GB emmc drive, however it only works if there is a 4K HDMI monitor attached to HDMI1, I was not able to get it to display on a 1920x1200 HDMI monitor nor a USB connected or HDMI connected portable display (2560x1440). The Gnome version will boot with any of those 4 types…

Built image with such flags: Etched img to sdcard and SBC has no response on power up. U-boot log: OS boots normally if I use ext4, but would like to stick to f2fs. Btrfs or f2fs used to work if I used 7 months old armbian-build git checkpoint but not any more. Anyone else had similar problems?

Hi all I hava an orange pi 5 plus with a 512GO NVME SSD. I have installed the latest version od Armbian to a SD card it work well, but for speed reason i would like to install the OS to th SSD drive and boot from this device and no longer from the SD card. Is there a way to do this ? i mean from u-boot point of view? i can keep a SD card inside it to store u boot but i would like to move usr var and such to SSD Thanks in advance for your answers comment or ideas W.

I installed latest Armbian_24.5.1_Orangepi5-plus_bookworm_vendor_6.1.43_minimal.img and I can't get wifi to work. The adapter is RTL8852BE. I installed armbian-firmware-full and the adapter is shown in lspci, but there is no wireless interface. armbian-config does not list wifi as an option. armbianmonitor -u

There's a strange issue with my orange pi 5 plus. When I boot into the ubuntu image, everything is fast, stable and zippy. But when I boot into the openmediavault image, it's incredibly slow. Simple operations like apt upgrade crawl. I noticed the cpu frequency is stuck at 408 MHz in htop in the openmediavault image. I ran a test. I opened another console and ran yes. Went back to htop and the frequency was still stuck at 408 MHz with one core pegged at 100% from the yes. So I fired up the ubuntu image and did the same thing. The core was at 100% but the frequency was at 2304mhz on that core. There is something wrong with the openmediavault …

I am trying to build armbian image via WSL 2, as I have done hundreds of times in the past. I ensured that the wsl2 distro (Ubuntu) was up to date via apt update and apt upgrade, and ran git pull was issued within /build folder prior to issuing ./compile.sh. Several files failed to download during the build including: [💲|🔨] E: Failed to fetch http://security.debian.org/dists/trixie-security/main/binary-arm64/Packages 404 Not Found [IP: 151.101.130.132 80] [💲|🔨] E: Failed to fetch http://deb.debian.org/debian/dists/trixie/main/i18n/Translation-en 404 Not Found [IP: 151.101.130.132 80] [💲|🔨] E: Failed to fetch http://deb.debian.org/debian/dist…

I want to share some information about an issue that I see on my OPi5+. Since I got it I am messing around with it and everything works great so far with the edge 6.7 kernel. One thing I noticed though was, that right after installation with nothing connected and when idle, there was one kernel process that was constantly consuming around 10% CPU time and the load stays at 1. The process was irq/136-hym8563. The number varies of course after each boot. Kernel driver is rtc_hym8563. Since it is build into the kernel I was not able to unload it as a first test. Side node, the issue is not seen on the Rock5b, so it seems OPi5+ hardware specific. Even if bot…

I am trying to compile a new kernel in order to support some satellite receiver tuner (from TBS). I did that successfully (In February 2023) on Orange Pi 5 with Linux kernel 5.10.110, but I am struggling doing it with Orange PI 5 Plus with Linux 5.10.160 (jammy). Basically I would like to turn as Modules lots of CONFIG_VIDEOBUF2_*, in order to replace the modules with the ones compiled separately (that I know are working fine with my TBS USD card). These are my issues: - I do not manage to set separately those CONFIG_VIDEOBUF2_* through the menu config. - Thus I tried to set the whole "multimedia support" as a module and go…

Hello everyone, This is my 1st post on the forum. My intention with this post is not to report a specific issue that I am running into, but more because I would like to collect info and suggestions from people with more experience than myself. I've recently received an Orange Pi 5 Plus and have spent a bit of time exploring operating systems suitable for this system and have settled on the Armbian solution. I'm a HW designer by trade, and have done some SW work, but I do not consider myself proficient in SW at all. I find my way around things, but that's about as far as it goes.... For the my planned use of the OPi5+, I will need eMMC b…

After enabling the rk3588-hdmirx overlay in armbian-config device tree overlays, whenever I boot, I am greeted with multiple hdmirx (fdee0000.hdmirx-controller: hdmirx_wait_lock_and_get_timing HDMI pull out, return!) errors on boot. On a previous install, the hdmirx errors would block the entire boot process and it would just hang forever. I do not know the exact cause, but the issues seemed to arise after I ran this command to disable the X Display Server "systemctl set-default multi-user.target". The errors could only be resolved if I plugged in the sd card into another device and removed rk3588-hdmirx from overlays in /boot/armbianEnv.txt . …

Can you help me with the contents of the file name? I understand edge, vendor, but then there are other suffixes that are not clear to me: are gnome-oibaf_desktop the same "kernel release" as the xfce_desktop or minimal? Or there are patches that are applied only to a specific version? Thanks!

I'm running armbian 23.08 bookworm on an orange pi 5 plus. I'm trying to run VMs that boot with UEFI, but these are hanging. I suspect a bug in the vendor kernel (5.10.160-rk35xx), since this works fine on an AWS bare metal arm64 host. Example: ``` $ sudo apt install qemu-system qemu-efi-aarch64 ... $ cp /usr/share/AAVMF/AAVMF_VARS.fd ./aavmf_efivars.fd $ qemu-system-aarch64 \ -machine virt \ -cpu max \ -drive if=pflash,unit=0,format=raw,readonly=on,file=/usr/share/AAVMF/AAVMF_CODE.fd \ -drive file=aavmf_efivars.fd,format=raw,if=pflash -net none \ -nographic \ -enable-kvm …

Dear Armbian Community, I hope this message finds you well. I am encountering an issue with PWM on my Orange PI 5 Plus running Armbian. Despite my attempts, I am unable to utilize PWM via GPIO pins. Upon navigating to /sys/class/pwm, I can only see the pin designated for controlling the fan. The PWM pins on the GPIO are not visible. I have successfully controlled GPIO pins using WiringPi and Go Lang Periph libraries; however, when attempting to use PWM via GPIO, I encounter the following error: I have also checked the “hardware setup” screen in armbian-config, where I can see two hardware components listed, but PWMs are not among them. …

So I was messing around with my new OrangePi-5+ and installed the EDK2 UEFI firmware for Rockchip RK3588 platforms onto the SPI flash (/dev/mtdblock0). After which I tried all sorts of images and kernels with varying success, only the 5.10.160-legacy-rk3588 kernel would really have a working display. Until I tried a generic UEFI arm64 image (Jammy-CLI on a USB stick) which gave a working display, albeit at 1080p max. (my monitor is 4K) with no acceleration (after the extra steps), and installed the Mate desktop (just my preference). The big caveat is that it does not recognize the SD-card, EMMC or SPI-flash, just regular drives (e.g. sda/nvme0n1 etc) and I'm…

I purchased the wifi + bt module. It is RTL8852BE. my armbian: Linux orangepi5-plus 5.10.160-legacy-rk35xx #1 SMP Fri Feb 2 07:51:33 UTC 2024 aarch64 aarch64 aarch64 GNU/Linux My Bluetooth never works. It cannot be listed under hciconfig: vnc@orangepi5-plus:~$ hciconfig -a vnc@orangepi5-plus:~$ rfkill ID TYPE DEVICE SOFT HARD 0 bluetooth bt_default blocked unblocked 1 wlan phy0 unblocked unblocked vnc@orangepi5-plus:/$ sudo cat /var/log/dmesg | grep "\(luetooth\|RFKILL\)" [sudo] password for vnc: [ 4.299662] kernel: Bluetooth: Core ver 2.22 [ 4.299678] kernel: Bluetooth: HCI device and connection …

Hi, I've been compiling my own Armbian images since 6.13-rc5, and now 6.13 and I noticed that when I compile i3, youtube videos and webgl tests don't work as great when I compile i3 with mesa-vpu as it does when I compile e.g., cinnamon. I also noticed that the suffix is not -mesa-desktop, only -desktop. Is it as per design and i3 doesn't include mesa at all, or is it some kind of bug? Thanks!

Hello! First time poster, long time admirer. I've been unable to get ANY of the 6.10.x images to boot off SD card (Sandisk Extreme) for the Orange Pi 5 Plus. Specific images which are not working for me: Armbian_24.8.0-trunk.472_Orangepi5-plus_noble_edge_6.10.2_gnome-kisak_desktop.img.xz Armbian_24.5.5_Orangepi5-plus_noble_edge_6.10.1_gnome-kisak_desktop.img.xz Armbian_24.8.0-trunk.472_Orangepi5-plus_trixie_edge_6.10.2_minimal.img.xz Has anybody else had better luck?

Hey everyone. New to Armbian and Orange Pi, but no stranger to everything I ever try do do being a major hassle! So here's the deal. Installed Armbian jammy 5.1 for orange pi plus. Working nicely. Except some of you might remember me from earlier today when I was struggling to get my ax210ngw working correctly (thanks by the way. Fixed that)! So I follow the process to switch from SD card to my Samsung 980 pro 1tb nvme. Bit of confusion getting it to show as an option in armbian-install, but I got it. Formatted in ext4 with a partition via gparted--now every time I try to run the install script, no matter which option I choose, it either freezes or…

Since at least one week I find the system every morning with solid red led, waiting for a command in uboot. When looking at the journal messages, the last messages are always: Feb 10 23:45:01 etnas2 CRON[5176]: pam_unix(cron:session): session opened for user root(uid=0) by (uid=0) Feb 10 23:45:01 etnas2 CRON[5177]: (root) CMD (/usr/lib/armbian/armbian-truncate-logs) Feb 10 23:45:01 etnas2 CRON[5176]: pam_unix(cron:session): session closed for user root Feb 11 00:00:01 etnas2 CRON[5213]: pam_unix(cron:session): session opened for user root(uid=0) by (uid=0) Feb 11 00:00:01 etnas2 CRON[5212]: pam_unix(cron:session): session opened for user root(uid=0) by (uid=0) Feb…

Is there an overlay or any other way of getting the Orange Pi 5 Plus to work with a 1024x600 display?

SoC Rockchip RK3588 (8nm LP process) CPU • 8-core 64-bit processor • 4 x Cortex-A76(2.4GHz), 4 x Cortex-A55(1.8GHz) and separate NEON co-processors GPU • Arm Mali-G610 • Built-in 3D GPU • Compatible with OpenGL ES1.1/2.0/3.2, OpenCL 2.2 and Vulkan 1.2 NPU Embedded NPU supports INT4/INT8/INT16/FP16 mixed operation, with up to 6Tops computing power PMU RK806-1 RAM 4GB/8GB/16GB （LPDDR4/4x） Memory • QSPI Nor FLASH: 16MB/32MB • MicroSD card slot: up to 128GB • eMMC socket: 16GB/32GB/64GB/128GB/256GB eMMC module can be attached • M.2 2280 slot for NVMe SSDs (PCIe 3.0 x4) up to 2,000 MB/s USB • USB3.0 × 2 • USB2.0 × 2 • Type-C ×1 Video • 2x HDMI …

Continuing the tradition (1, 2) of micro-optimizations for single-board computers that come into my hands. This time I optimized or rather fixed the wake-up function via USB/WoL/WWoL on the Orange Pi 5 Plus. Also got the WiFi adapter RTW8852BE/RTW8852CE working (at least those are the ones I tested). I tested exclusively on the Vendor 6.1.x kernel since the main wake-up features via USB/PCIE/GPIO1-GPIO4 only work in it. I don't currently have the ability to test the new current kernel and I doubt that Power Management will work fully there. Armbian for Orange Pi 5 Plus from the official website, Vendor kernel (kernel 6.1.115-vendor-rk35xx), what does…

On the OrangePI-5-Plus, using an edge kernel, I've found that the desktop environment's GPU rendering works very smoothly on Wayland, in KDE 6 on Debian Trixie. It renders much more smoothly than gnome with Wayland (it's been my experience that the edge kernel is the only one that works). But I've encountered a major rendering bug. It only appears in Trixie KDE Plasma 6 with Wayland rendering. It does not appear when using x11 or when using either rendering in gnome. Nor does it appear at all in Bookworm. I have tried all kinds of things to "fix" these to no avail, including installing more wayland and mesa packages, then upgrading them to stable b…

It was found that 3.5mm jack has issue with using headset. Speakers are work good on my "uname -a Linux orangepi5-plus 6.19.0-rc5-edge-rockchip64 #1 SMP PREEMPT Mon Jan 12 03:03:14 UTC 2026 aarch64 aarch64 aarch64 GNU/Linux" system but micro is silent. By debugging it was found that register 0x2b(43) "DAC Control 21" has difference between actually used es8388 on OP5+ and original driver's IC es8328. Also microphone bias was never activated by bits 2,3 in register 0x03. I create patch and now microphone work properly. I don't know how to properly share this patch so I will attache it here. orangepi-5-plus_ES8388_Microphone.patch

Desktop images with Armbian Linux v6.12 variant Cinnamon with mesa/vpu support fails to boot from SD card. The message displayed on screen is "Begin: Running /scripts/init-premount ... (initramfs) _" SPI was erased, and the minimal install have no issues booting from a sd card. The SBC is an Orange Pi 5 Plus with 16gb ram

After looking at this message from @Seb042 I thought it would be better to open a new topic to discuss this. From what I saw from my install: $ dmesg ... [ 6.166453] iwlwifi 0002:21:00.0: api flags index 2 larger than supported by driver [ 6.166480] iwlwifi 0002:21:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 93.8.63.28 [ 6.167021] iwlwifi 0002:21:00.0: loaded firmware version 59.601f3a66.0 ty-a0-gf-a0-59.ucode op_mode iwlmvm [ 6.267334] iwlwifi 0002:21:00.0: Detected Intel(R) Wi-Fi 6 AX210 160MHz, REV=0x420 [ 6.273748] iwlwifi 0002:21:00.0: reporting RF_KILL (radio disabled) [ 6.450150] iwlwifi 0002:21:00.0: WFPM_UMAC_PD_NOTIFIC…

Hi all, I'm using a UEFI based edge ubuntu 24.04 image which reported a kernel stack trace (system still seems functional and no ongoing issue/messages) - [ 22.382942] rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 5-.... } 6 jiffies s: 381 root: 0x20/. [ 22.382966] rcu: blocking rcu_node structures (internal RCU debug): [ 22.382972] Sending NMI from CPU 7 to CPUs 5: [ 22.382983] NMI backtrace for cpu 5 [ 22.382995] CPU: 5 PID: 92 Comm: kworker/u16:2 Tainted: G W 6.8.5-edge-arm64 #2 [ 22.383004] Hardware name: Orange Pi Orange Pi 5 Plus/Orange Pi 5 Plus, BIOS v0.9.1 10/12/2023 [ 22.383009] Workqueue: writeb…

playing around with armbian-config after switiching to vendor kernel - missing "toogle hardware configuration" Left is on (previous legacy vendor) kernel with "24.5.1 and right is legacy kernel with "24.2.1"" Just curious if anyone know why that is? Perhaps I should have taken other steps when switching to vendor kernel(I have rebooted and confirmed it is running vendor kernel prior to screenshot)

HI, On one orangepi5B, it seems not possible to have details from u-boot when starting target. The first messages on HDMI start with the kernel root@hn-orangepi5b-450:~# dmesg |head [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000] Linux version 6.12.0-current-rockchip-rk3588 (build@armbian) (aarch64-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #3 SMP PREEMPT Sun Nov 17 22:15:08 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Xunlong Orange Pi 5 [ 0.000000] efi: UEFI not found. [ 0.000000] NUMA: Faking a node at [m…

Hello, I am using Armbian 23.8.2 Jammy for Orange Pi 5 PLus and it cannot diplay 4K via HDMI. How to enable/switch this on?

I have built an Orange Pi 5 Plus systems. I have a 256gb eMMC card which seems to run as speed would expect. Yet when I test the NVMe drive I get slow speeds compared to what is suggested to get. I have seen other people posts that suggest they are getting at least 4gb/s using NVME drives. I have searched for other issues but there is no errors in the logs just can't get the speeds I was expecting. I have the following which suggests at least 5gb/s KINGSTON SNV3S500G I have formatted it using Ext4. root@orangepi5-plus:/boot# hdparm -Tt /dev/nvme0n1 /dev/nvme0n1: Timing cached reads: 2804 MB in 2.00 seconds = 1404.10 M…

I have set up Armbian 24.8.4 bookworm on my 32GB Orange Pi 5 Plus. Most everything works as expected out of the box. The second HDMI port doesn't detect the second screen, and the screen displays No Signal. I have tested the cables and monitors to ensure they are functioning. I have also ensured I wasn't plugged into the HDMI input by accident. I was about ready to proclaim it a hardware issue, but on booting the "Official" Orange PiOS Arch image, the dual monitor support worked as expected. I checked the dtb file included with the Arch image, and it has many references to HDMI0 and HDMI1 devices, while the one used by default with the Armbian ima…

I have Orange Pi 5 Plus that I plan to install in a remote location. To boot Orange Pi, I need to press the physical Power On button. How I can setup the machine to boot automatically once the power is supplied? There is nobody on the remote side to press this button. Or maybe there are other options to boot remotely like WakeOnLAN? Where it can be configured? In orangepi-config?

Hello everyone I was trying to look for information in the forum but I can't find any topic where this specific issue is discussed. I also looked for help in the omv forum and they told me it was a problem with the distribution, hopefully you can help me. My system running Armbian_24.5.1_Orangepi5-plus_bookworm_vendor_6.1.43_minimal Install OMV, omv extras, i try to configure the compose folders and i get the 500 internal server error, clear cache, update and reboot system but there is no change, a moderator asked me for the log by executing the following command "Your error output is incomplete. What is the output of: sudo omv-salt …

Hi there, I've been trying to enable g_ether and USB OTG on my Orange PI 5+. I've tried things like editing /boot/orangepiEnv.txt and adding module-load dwc2,g_ether. However, I don't get any usb0 interface pop up which indicates to me that the USB/OTG mode is not set to peripheral on the settings. I'm not sure how to go about it? Would anyone be able to advise? I want to use the power port for also Ethernet.

Hi Guys, I just did a new custom Armbian build ./compile.sh BOARD=orangepi5-plus BRANCH=vendor RELEASE=noble KERNEL_ONLY=yes KERNEL_CONFIGURE=no. The image is Armbian-unofficial_25.11.0-trunk_Orangepi5-plus_noble_vendor_6.1.115_cinnamon_desktop and when I installed it on orangepi I see it is not supporting Panfrost/Mail: glxinfo | grep -E "OpenGL renderer|OpenGL version" OpenGL renderer string: llvmpipe (LLVM 20.1.2, 128 bits) OpenGL version string: 4.5 (Compatibility Profile) Mesa 25.0.7-0ubuntu0.24.04.2 but for older image Old_Armbian-unofficial_25.08.0-trunk_Orangepi5-plus_noble_vendor_6.1.115_cinnamon_desktop All was well glxinfo | grep -E "OpenGL rend…

Hi. I am not complaining. I just would like to understand why I must deactivate https://ppa.launchpadcontent.net/liujianfeng1994/rockchip-multimedia/ubuntu/ if I want watching video on Youtube. If it's needed to disable this repo for watching video. I am ok. But why I can't read video with package from this repo? https://paste.armbian.com/vaxedisuda

Hi all Cannot make usable wol on my orange pi 5 plus. Os: Armbian 24.5.1 Bookworm with Linux 6.1.75-vendor-rk35xx WOL tested in magic or unicast settings or all flags enabled (phy, unicast, multicast, broadcast, arp, magic) Test sending wol packets with running tcpdump -i enP3p49s0 '(udp and port 7) or (udp and port 9)' show that orange pi successfully receive wol packets on speeds 1000 or even 10 mbps while powered on. But after sending orange pi to suspend or power off I cannot bring it online via WOL. So I suppose network component outside orange pi is ok and it is something wrong with orange pi. Any ideas?

Hi, my orange pi 5 plus cant boot armbian, its hang and screen goes flicker, im currently not been able to boot android images to (its hang and flicker to),, i cant boot armbian and android version.. but other linux is normally booting fine.. any advise?

Hi, I went to see if there were any updates to the OPi5+ images and saw the OPi5 had updates. I clicked on the link on the main download page. https://www.armbian.com/orangepi-5/ https://redirect.armbian.com/orangepi5-plus/archive/ I've come back and now it has desktop images but no server images.

Hello again, Based on the recommendations provided in a previous ticket, I have decided to attempt to build a custom image for the Orangepi 5 Plus. I read the docs provided in the link of that post and noticed that there is no mention of installing the cross complier tool chain for arm in ubuntu 22.04, which I just downloaded for this purpose. Do I need to install those tools or will that be addressed once I clone the git repo and run the compile.sh BOARD=orangepi5-plus ? Also the instructions mention Multipass and Docker, I have a Debian 12 workstation with virt-manager installed, will that work or will I need a dedicated ubuntu 22.04…

EDIT: I tried using ext4 rather than btrfs and.. somehow that solved it? I don't understand how the SSD file system would change how the bootloader is flashed because if properly flashed, the SD card shouldn't work at all, unless something has changed. Hey all, I wanted to move to the newest version of armbian (25.2.1) and for whatever reason neither `apt update && apt upgrade` nor `armbian-upgrade` (as a sanity check) worked so I wiped the SPI flash using `mtdtools` as prescribed in the forum post linked on the support page. 1) Booted from SD, installed Armbian and the bootloader. 2) Shut down, removed SD and turned on. Machine hung and never boote…

Hello. The official adapter does not work for my orange pi 5 plus. https://aliexpress.ru/item/1005005956334270.html?spm=a2g2w.orderdetail.0.0.4e224aa6r3APff&sku_id=12000035019805399 The problem is this. Wi-Fi works, you turn on bluetooth, bluetooth doesn’t work initially. After turning on bluetooth, Wi-Fi does not work and bluetooth does not work either. Realtek RTL8852BE-CG BE CPU work in all officials builds. Help me please

Hi, newbie here again.... I recently switched to Armbian from Orange Pi Ubuntu. I am running Armbian 23.8.1 Jammy with Linux 5.10.160-legacy-rk35xx My issue is a noticeable slowdown in NVME performance. I now get 522.35 MB/sec (as per hdparm test), but before on orange pi ubuntu it was around 1900 MB/s . FYI...Armbian is installed on and booting from the NVME. everything else seems to work perfect and I don't get smartctl errors. Please advise - Crucial P3 4TB PCIe M.2 2280 SSD NVMe (PCIe Gen 3 x4) - Have all the latest updates /dev/nvme0n1: Timing cached reads: 7988 MB in 2.0…

I installed latest vendor image and because of the wifi issues I switched to the edge kernel. I messed up my fstab, couldn't connect with ssh, so I plugged it to my monitor and a keyboard, but there was no video. Eventually, I fixed it by booting vendor image from my sd card, but I got curious. I know, that vendor image just works, so I flashed edge image to my sd card to see what's wrong. The monitor recognizes the presence of the board, but it's just a black screen. I can ssh to the board, so the image definitely booted, but there's just no video. Here's the log from my original installation. I kept 6.8 kernel because the video is not important to me.

I am using Orange Pi 5 Plus with eMMC. I tried to install a program I need, but an error occurred saying that installation was not possible because SecureBoot was disabled on the system. So I need to enable SecureBoot, how do I do that? Thank you.

I have built and used it with the latest source and still HDMI audio and analog audio does not work. Is there any way to get HDMI audio to work other than using the vendor kernel?

Hello, good afternoon. I'm using a translator, so I apologize if it's not clear. I have an Orange Pi 5 Plus SBC which I have Android installed on the m2 drive. I install Armbian on a microSD card. I don't remember what problem I was having, but I had to format the SPI Flash. After that, the Armbian version worked fine. Also, after formatting the SPI Flash, my microphone stopped working on Android (it works on Armbian). Could this be due to formatting the SPI Flash? Thank you.

I followed the provided instructions to install Arbmbian on Orange Pi 5 Plus 16GB, so I downloaded the official Ubuntu image from the Orange Pi website, and when it booted, it sudo apt update sudo apt install mtd-utils sudo flash_eraseall /dev/mtd0 The flash operation was finished successfully. Then I turned off, loaded Armbian Ubuntu 24.04 (Noble) (Desktop images with Armbian Linux v6.12) on SD and started the machine. I have a monitor connected to the machine, but there is no output. My router doesn't show any new network device, so I suppose that Armbian doesn't load. It's exactly the same situation when I tried to install Armbian without /dev/mtd0 erasin…

Hi all , Just installed last supported version: Armbian 24.8.1 Noble Gnome, MESA / VPU, Kernel: 6.1.75, Size: 1.5 GB, Release date: Aug 26, 2024 I have 2 dell monitors : u2515h ultrasharp 1440p, and more modern P3424WE with 3440x1440 max resolution. With both - armbian max resolution in display settings is always 1920x1080. My previous experience here was with radxa zero D1 and 1440p was working here smoothly out of box on different armbian images. I also tried Ubuntu 22.04 (Jammy)KDE NeonMESA / VPU https://dl.armbian.com/orangepi5-plus/Jammy_current_kde-neon-kisak with same results: no resolution higher then 1080p …

Hello, I've been using https://joshua-riek.github.io/ubuntu-rockchip-download/boards/orangepi-5-plus.html with a custom kernel that I built to activate my TPM2.0 device and it works. Now I'm asked to use an UEFI compatible image with my Orange Pi 5 Plus. So what I did is more or less the same thing that in here But instead of the legacy kernel I used the 6.1.115-rockchip-vendor-rk35xx kernel and my device booted, I got an HDMI output, etc. And then I updated it to my custom kernel (6.1.0-1027-rockchip) that has the necessary configurations to allow TPM over SPI. Now I'm trying to activate my TPM2.0 as I did before. To do th…

My setup includes orange pi 5 plus, Samsung NVME SSD M2 4 TB with Armbain os. 256 GB eMMC and Intel BE 200 Wi-Fi. There are no drivers for the intel BE 200 Wi-Fi or any instructions to make it work.

Hi folks, Ran into some issues with July 6 bookworm images for Orange Pi 5 Plus - it boots but there is no video or network. Orange Pi 5B has a note to change the dtb - one is also needed for the 5 Plus. It should be `fdtfile=rockchip/rk3588-orangepi-5-plus.dtb`. (I tried to search for related issues, but the rate limit is stopped me so I gave up.)

I have a new Orange Pi 5 plus 16GB. Seems a pretty cool board and I want to replace my old Rpi 4 for Media center and Home assistant. I tried several distribution but can't get all my stuff working. The OPI5+ is attached to an onkio 5.1 receiver and the receiver go to a FHD TV. What is want to achieve is in Kodi 1. play video with GPU 2. libCec in Kodi to control Onkio volume 3. Passthrough audio Is there a working solution? Thank you

I've downloaded the Armbian 25.5.1 (Kernel 6.12) Home Assistant image (https://dl.armbian.com/orangepi5-plus/Bookworm_current_minimal-homeassistant), burned to microsd and rebooted the orange pi 5 plus. I burned the image to a microsd cards, inserted the microsd and did a hard reboot of the SBC. The error message is "Gave up waiting for root filesystem device."

Hello Is it possible to install Emby Server in Orange Pi5 plus? Regards Hugo