Orange Pi 5 Plus

Board: Orange Pi 5 Plus (RK3588) Armbian image used: Downloaded from https://armbian.cn/boards/orangepi5-plus (Ubuntu 26.04, .img format) Comparison image: Joshua Riek's Ubuntu for Rockchip – https://joshua-riek.github.io/ubuntu-rockchip-download/boards/orangepi-5-plus.html Problem Description I downloaded the Armbian image for Orange Pi 5 Plus from the official Armbian page and flashed it to both a TF card and eMMC. The board fails to boot in either case. However, when I flash Joshua Riek's Ubuntu image using the exact same methods, the board boots successfully without any issues. I have compared the partition layouts of both images and found them to be essenti…

I have built and used it with the latest source and still HDMI audio and analog audio does not work. Is there any way to get HDMI audio to work other than using the vendor kernel?

I am running Ubuntu 24.04 Noble (Armbian Linux 6.1.115-vendor-rk35xx) and no additional packages affecting VPU performance have been installed; everything is stock. Jellyfin is running in Docker, and transcoding works perfectly, except for some movies. I tried to play a 4K video in Chrome (native HEVC support), set the bitrate to 40mbps, and the video played normally at a transcoding speed of about 3x, but after a while, Orange Pi crashed. In Firefox inside neko (where there is no hardware acceleration and HEVC), the crash happened even faster, after ~2 seconds of playback. The crash happens as if the board loses power: journalctl is not saved, nothing is …

i recently purchased an orange pi 5 plus 16gb with the wifi / bt card, the aluminum wifi case, fan and 1tb ssd. when i go to the official website i see different images there none of which seem to work 100%. i mean i was able to get each up and running but what i noticed is that the graphical drivers would not load. i saw a youtube video claiming armbian has the right driver support for the mali 610 gpu. can someone assist me getting this to work? im big into emulation gaming and right now it doesnt even have Vulkan support i crave. someone help thanks

I was able to install the latest Armbian/Ubuntu-Resolute 26.8.3 image on my Orange Pi 5 Plus without a lot of fanfare. It took a bit of hunting around to find the correct process to get the image written to an SD card with the new Armbian Imager and then push that image to my emmc storage after it booted, but it was rather painless otherwise. It seems to work without any issues on my 2.5GB/10GB network and is acting as my home Jellyfin media server for now. It was doing that before running Ubuntu 24.04 with a an older 6.1 kernel from the vendor. Zero complaints with the old setup, but I wanted a newer and better supported kernel build given all the excitement around t…

I'm using Armbian Orange Pi 5 Plus based on Debian 13 with vendor kernel v26.2.1 for Orange Pi 5 Plus running Armbian Linux 6.1.115-vendor-rk35xx I'm thinking about switching to Armbian based on Debian 13 with kernel current 6.18.33 because 6.1.115 is an old one => current the kernel is more recent Is that a good idea to swith to vendor kernel to current ? How can I do this ?

Dear team, On Armbian_25.11.1_Orangepi5-plus_trixie_current_6.12.58_minimal.img not possible to boot kernel, only u-boot seems available ? Bellow is the debug log on tty DDR V1.13 25cee80c4f cym 23/08/11-09:31:58 LPDDR4X, 2112MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=18 CS1 Row=18 CS=2 Die BW=8 Size=8192MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=18 CS1 Row=18 CS=2 Die BW=8 Size=8192MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=18 CS1 Row=18 CS=2 Die BW=8 Size=8192MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=18 CS1 Row=18 CS=2 Die BW=8 Size=8192MB Manufacturer ID:0xff CH0 RX Vref:28.5%, TX Vref:22.8%,21.8% CH1 RX Vref:27.1%, TX Vref:21.8%,21.8% CH2 R…

I am trying to build armbian image via WSL 2, as I have done hundreds of times in the past. I ensured that the wsl2 distro (Ubuntu) was up to date via apt update and apt upgrade, and ran git pull was issued within /build folder prior to issuing ./compile.sh. Several files failed to download during the build including: [💲|🔨] E: Failed to fetch http://security.debian.org/dists/trixie-security/main/binary-arm64/Packages 404 Not Found [IP: 151.101.130.132 80] [💲|🔨] E: Failed to fetch http://deb.debian.org/debian/dists/trixie/main/i18n/Translation-en 404 Not Found [IP: 151.101.130.132 80] [💲|🔨] E: Failed to fetch http://deb.debian.org/debian/dist…

I have an Orange Pi 5 Plus 16GB board, revision "1.3.1". I've been using it for about a year with official Armbian, Vendor kernel 6.1. The only issues I noticed were a non-working Type-C port and FAN connector. I thought it was an OS or DTS (Device Tree) bug... But it turned out to be a hardware problem. It started when I got another Orange Pi 5 Plus 8GB board for repair (needed to resolder the Type-C power connector). Same revision "1.3.1". Скрытый текст (left is my 16GB board, right is the 8GB board for repair; the PCB solder mask is slightly different in shade of blue — probably different manufacturers or production batches) …

Introduction This guide describes a tested method for running Android, Armbian, and Ubuntu on the same NVMe SSD of the Orange Pi 5 Plus. This is not an official Orange Pi installation procedure. The entire workflow was developed through extensive real-world testing. The following configuration has been successfully verified: ✅ Android boots from the NVMe SSD. ✅ Armbian boots from the same NVMe SSD via UEFI. ✅ Ubuntu boots from the same NVMe SSD via UEFI. ✅ All three operating systems coexist on a single NVMe SSD. ✅ Armbian and Ubuntu share the same EFI partition. ✅ Android, Armbian, and Ubuntu can share a common data partition. 1. Requirements Har…

Hello All.. I am trying to get rknpu working properly. I have resolute minimal install with 6.1 vendor kernel installed. Default install does not have `/dev/rknpu` and shows error with loading the rknpu driver. Can any one help resolve this? This is with fresh install of the OS on the NVME drive: There is no NPU option in the dtb list for orangepi5plus. PRETTY_NAME="Armbian 26.5.1 resolute" NAME="Ubuntu" VERSION_ID="26.04" VERSION="26.04 (Resolute Raccoon)" VERSION_CODENAME=resolute ID=ubuntu ID_LIKE=debian HOME_URL="https://www.armbian.com" SUPPORT_URL="https://forum.armbian.com" BUG_REPORT_URL="https://www.armbian.com/bugs" PRIVACY_POLICY_URL="https://w…

Hi I managed to fix an issue with the usb-c port of the orange pi 5 plus. It seems the device is not activated unless you put it in host mode yourself: as user root: echo host >/sys/kernel/debug/usb/fc000000.usb/mode I have tried a usb-c network card and usb stick. Both work after this command! I noticed this when I installed the 6.1.115-vendor-rk35xx kernel. This one does not need this setting, it switches automatically from device mode to host and vice versa. I had alot of problems with analog sound on older kernels, e.g. youtube just hangs unless you mute the sound. But sound in noble 6.19.0-edge-rockchip64 wo…

Hello, good afternoon. I'm using a translator, so I apologize if it's not clear. I have an Orange Pi 5 Plus SBC which I have Android installed on the m2 drive. I install Armbian on a microSD card. I don't remember what problem I was having, but I had to format the SPI Flash. After that, the Armbian version worked fine. Also, after formatting the SPI Flash, my microphone stopped working on Android (it works on Armbian). Could this be due to formatting the SPI Flash? Thank you.

Built image with such flags: Etched img to sdcard and SBC has no response on power up. U-boot log: OS boots normally if I use ext4, but would like to stick to f2fs. Btrfs or f2fs used to work if I used 7 months old armbian-build git checkpoint but not any more. Anyone else had similar problems?

Hi, I've read on here that you can apparently switch to a stable edge branch through Armbian Config, but the closest I can find is 'switch to rolling packages repository' and 'distribution upgrade to rolling unstable'. Are either of these correct? I'm running the Ubuntu Noble 6.12 kernel, btw. Many thanks.

Hi there, I'm really happy with Armbian on my Oprange Pi 5 Plus but recently I noticed that I'm not getting kernel updates so often as before. I use rockchip-edge branch and I'm stuck at kernel "6.18.0-rc6-edge-rockchip64". I know there are new versions being tested (https://github.com/armbian/os/pkgs/container/os%2Fkernel-rockchip64-edge), will they be released to armbian? Maybe you are working hard on Armbian version 26.2 and I'm just anxious Thanks in advance!

It was found that 3.5mm jack has issue with using headset. Speakers are work good on my "uname -a Linux orangepi5-plus 6.19.0-rc5-edge-rockchip64 #1 SMP PREEMPT Mon Jan 12 03:03:14 UTC 2026 aarch64 aarch64 aarch64 GNU/Linux" system but micro is silent. By debugging it was found that register 0x2b(43) "DAC Control 21" has difference between actually used es8388 on OP5+ and original driver's IC es8328. Also microphone bias was never activated by bits 2,3 in register 0x03. I create patch and now microphone work properly. I don't know how to properly share this patch so I will attache it here. orangepi-5-plus_ES8388_Microphone.patch

Hi all Cannot make usable wol on my orange pi 5 plus. Os: Armbian 24.5.1 Bookworm with Linux 6.1.75-vendor-rk35xx WOL tested in magic or unicast settings or all flags enabled (phy, unicast, multicast, broadcast, arp, magic) Test sending wol packets with running tcpdump -i enP3p49s0 '(udp and port 7) or (udp and port 9)' show that orange pi successfully receive wol packets on speeds 1000 or even 10 mbps while powered on. But after sending orange pi to suspend or power off I cannot bring it online via WOL. So I suppose network component outside orange pi is ok and it is something wrong with orange pi. Any ideas?

Continuing the tradition (1, 2) of micro-optimizations for single-board computers that come into my hands. This time I optimized or rather fixed the wake-up function via USB/WoL/WWoL on the Orange Pi 5 Plus. Also got the WiFi adapter RTW8852BE/RTW8852CE working (at least those are the ones I tested). I tested exclusively on the Vendor 6.1.x kernel since the main wake-up features via USB/PCIE/GPIO1-GPIO4 only work in it. I don't currently have the ability to test the new current kernel and I doubt that Power Management will work fully there. Armbian for Orange Pi 5 Plus from the official website, Vendor kernel (kernel 6.1.115-vendor-rk35xx), what does…

I understand that panthor is not supported for wayland but in that case I would expect libmali to fill in... but I ended up with lvmpipe. The overlay along with another recent post led me to believe that panthor was the expected default and libmali was an artifact, but I'm now questioning that after finding a thread identifying use cases where libmali can be preferred and a comment suggesting panthor wouldn't be available until 6.13. As a result, I am now questioning if there is a reason that software acceleration is the default and the user is expected to determine which path they want to go? I know support for the hardware has been slow going so I …

Why so few Debian (Trixie) images with this batch of newly released images? Not one full desktop image for Debian?

Hi Guys, I just did a new custom Armbian build ./compile.sh BOARD=orangepi5-plus BRANCH=vendor RELEASE=noble KERNEL_ONLY=yes KERNEL_CONFIGURE=no. The image is Armbian-unofficial_25.11.0-trunk_Orangepi5-plus_noble_vendor_6.1.115_cinnamon_desktop and when I installed it on orangepi I see it is not supporting Panfrost/Mail: glxinfo | grep -E "OpenGL renderer|OpenGL version" OpenGL renderer string: llvmpipe (LLVM 20.1.2, 128 bits) OpenGL version string: 4.5 (Compatibility Profile) Mesa 25.0.7-0ubuntu0.24.04.2 but for older image Old_Armbian-unofficial_25.08.0-trunk_Orangepi5-plus_noble_vendor_6.1.115_cinnamon_desktop All was well glxinfo | grep -E "OpenGL rend…

I have tried to download at least 3 times this image: Armbian_25.8.1_Orangepi5-plus_noble_vendor_6.1.115_gnome_desktop.img.xz All sha256sum verified Ok. And wrote 5 times on 3 different SDCards, and this img does not boot on my OPI-5-Plus. No image on monitor, partition armbi_root not expanded, no green lights... Just unusable (for me). Other img's that boot are OK: Deb-xfce, noble-cinnamon, noble-neon... Someone got success with this img??? I'm looking for a distro that works well on OPI5-Plus, well configured, and that works with HDMI audio. The best for now is Noble-Cinnamo…

Hello, I've been using https://joshua-riek.github.io/ubuntu-rockchip-download/boards/orangepi-5-plus.html with a custom kernel that I built to activate my TPM2.0 device and it works. Now I'm asked to use an UEFI compatible image with my Orange Pi 5 Plus. So what I did is more or less the same thing that in here But instead of the legacy kernel I used the 6.1.115-rockchip-vendor-rk35xx kernel and my device booted, I got an HDMI output, etc. And then I updated it to my custom kernel (6.1.0-1027-rockchip) that has the necessary configurations to allow TPM over SPI. Now I'm trying to activate my TPM2.0 as I did before. To do th…

Hi , I am trying to configure orangepi to turn on and turn off tv. I installed and used cec-ctl to register the boad as playbac device. And then was able to put the TV on standby mode via sudo cec-ctl --device /dev/cec0 --standby --to 0 but not able to find how to turn ON the TV. Can someone please help. Thanks Manish

Hello everyone! I was struggling to make wiring work on OrangePi 5 Plus armbian. Tried everything and came up with a solution that worked for me. I was constantly getting these errors: wiringPiSetup: mmap (PWM) failed: Operation not permitted wiringPiSetup: mmap (GPIO) failed: Operation not permitted I'm on 23.8.2. 1. Install armbian and update apt sudo apt update 2. As stated in OrangePi5Plus wiki page I got .deb installer for wiringPi on OrangePi Now here's the link to this file: https://github.com/orangepi-xunlong/orangepi-build/blob/next/external/cache/debs/arm64/wiringpi_2.51.deb 3. The mos…

due to network limitations， how to compile Ubuntu 22.04 Gnome OS image in offline mode, build.sh need to download many debs，can I download them in advance，then install them locally. I have already downloaded kernel and uboot.

I recently bought an orange pi plus and am using the armbian 6.12 server (https://dl.armbian.com/orangepi5-plus/Noble_current_server) I'm wanting to setup hardware acceleration for jellyfin but having trouble with the right steps. I'm using jellyfin inside docker on the orange pi inside armbian. I've found various tutorials but it seems like some of them reference things that no longer exist (like panfork seems to no longer be needed for latest mesa if I'm understanding correctly?), so wanting to see what I need to do to set this up. So it seems like I need to disable panthor and use mali instead, but I can't find in the armbian config menu the opt…

Hello, I just got a wifi 7 adapter (QCNCM865) and I was thinking the ath12k driver was available starting from kernel 6.13, I'm running the edge kernel 6.16.4 and the ath12k driver is failing to load and I can't find any wireless drivers in /usr/lib/modules/6.16.4-edge-rockchip64/kernel/net/wireless. Do I need to rebuild the kernel with the ath12k driver? or is there a kernel version available with that driver? Thanks for your help!

So I was messing around with my new OrangePi-5+ and installed the EDK2 UEFI firmware for Rockchip RK3588 platforms onto the SPI flash (/dev/mtdblock0). After which I tried all sorts of images and kernels with varying success, only the 5.10.160-legacy-rk3588 kernel would really have a working display. Until I tried a generic UEFI arm64 image (Jammy-CLI on a USB stick) which gave a working display, albeit at 1080p max. (my monitor is 4K) with no acceleration (after the extra steps), and installed the Mate desktop (just my preference). The big caveat is that it does not recognize the SD-card, EMMC or SPI-flash, just regular drives (e.g. sda/nvme0n1 etc) and I'm…

I'm adding this here as I want to contribute to the community, but I'm still not sure how. I've been playing with Armbian Build lately and found it's great for quick build images for testing purposes before it's officially made available. So I started build my own images with i3, mate, kde, and I noticed that, in my personal taste, the one that was better suited for my needs was Sway, but there's no desktop image with it. So I built a Server version and start installing it. I know it may not be of interest of everybody, so I was planning to do it for myself, so I can continue building with the interface, but having Sway "automatically" installed. …

Hey @amazingfate, I have an issue with the build-in IR receiver on my OPI5+: ##O#O## OS: Armbian 25.8.1 noble aarch64 ####### Host: Orange Pi 5 Plus ########### Kernel: 6.1.115-vendor-rk35xx ############# Uptime: 2 mins ############### Packages: 1934 (dpkg), 5 (snap) ################ Shell: bash 5.2.21 ################# Resolution: 3840x2160 ##################### DE: GNOME 46.0 ##################### WM: Mutter ################# WM Theme: Adwaita Theme: Adwaita [GTK2/3] Icons: Adwaita [GTK2/3] …

Hi there I'm using Ubuntu 24.04 (Noble) KDE Neon image from may 26, 2025. After download this image and installing it, Wayland was working fine, not problems at all. Then, after a system upgrade, if i choose Wayland from session manager, the system freezes and i can't boot with Wayland, only X11... Before the update, the system was smooth, now it's really laggy....Like i said, i'm using Desktop image with Armbian Linux v6.12 KDE Neon (Ubuntu 24.04) There's something wrong with the update Anyone knows why is this happening, and any turnaround to use Wayland again?

Hardware: OrangePI-5-Plus (rk3588), with "32 GB" of RAM Operating System: Debian Trixie (pure, except EFI boot and Armbian edge kernel) Root File System: Ext4 (encrypted) Desktop: KDE Plasma 6.3.6 (wayland, GDM3), KDE Frameworks version: 6.13.0, QT version: 6.8.2 EFI Source: https://github.com/edk2-porting/edk2-rk3588 The boot messages, after a few starts (spaced apart) of the low-memory-monitor.service, say there's a failure to start it. After booting is complete, here's a screenshot of the output of: systemctl status low-memory-monitor.service This error didn't show up until I installed a number of packages. I tracked down the off…

##O#O## OS: Armbian 25.8.1 noble aarch64 ####### Host: Orange Pi 5 Plus ########### Kernel: 6.1.115-vendor-rk35xx ############# Uptime: 1 day, 8 hours, 17 mins ############### Packages: 1852 (dpkg), 5 (snap) ################ Shell: bash 5.2.21 ################# Resolution: 3840x2160 ##################### DE: GNOME 46.0 ##################### WM: Mutter ################# WM Theme: Adwaita Theme: Adwaita [GTK2/3] Icons: Adwaita [GTK2/3] Terminal: x-terminal-emul CPU: (8) @ 1.800GHz …

HW: OrangePi5 Plus 32 32 GB RAM 512 GB NVME 5K Monitor Image: Armbian_25.8.1_Orangepi5-plus_trixie_vendor_6.1.115_xfce_desktop.img prepare system before each case dd if=u-boot-V2024.04-orangepi5-plus-spi.img of=/dev/mtdblock0 flash_erase /dev/mtd0 0 0 case 1: 1. copy image to 64GB uSD 2. booting 3. system comes up with xfce 4. sudo apt-get -y update; apt-get -y upgrade 5. reboot 6. system comes up, without desktop. system is reachable with ssh case 2: 1. copy image to 64GB uSD 2. booting 3. system comes up with xfce 4. armbian-install 5. choose boot from mtd flash 6. choose nvme0n1p1 6. update mtdbloc…

the issue is as follows: 1. When using the Type-C interface to connect to an external monitor, the display works normally if the monitor is connected after the development board has started. 2. If the monitor is disconnected and then reconnected after approximately several hours (possibly more than 6 hours), the display fails to show any image. I used the `armbianmonitor -u` command, and it output the following URL. https://paste.armbian.com/foyecusoju If the Type-C interface is functioning normally, the latest output from `dmesg -w` would show the following: [ 1155.922647] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller [ 1155.922692]…

I followed this manual I tried to boot , led was green and red , Display did not work. But Orange pi official images ca n boot my machine. How can I solve this problem?

On the OrangePI-5-Plus, using an edge kernel, I've found that the desktop environment's GPU rendering works very smoothly on Wayland, in KDE 6 on Debian Trixie. It renders much more smoothly than gnome with Wayland (it's been my experience that the edge kernel is the only one that works). But I've encountered a major rendering bug. It only appears in Trixie KDE Plasma 6 with Wayland rendering. It does not appear when using x11 or when using either rendering in gnome. Nor does it appear at all in Bookworm. I have tried all kinds of things to "fix" these to no avail, including installing more wayland and mesa packages, then upgrading them to stable b…

I made a configuration via armbian-config, but the camera does not work, here are the messages /sys/bus/i2c/drivers/ov13855 3-0036 bind uevent unbind sudo i2cdetect -y 3 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- UU -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- UU -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- 58 -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -- …

Hello everyone, I flashed the armbian into my tf cand and inserted it into my OrangePi 5 Plus, with my fans inserted to the specific socket on board (2pin, 1.25mm, 5V, PWM3_IR_M1). However, when I booted it, the fans was running constantly instead of controlled by temperature dynamically, like the official OS images that did only the fans running when the temperature over 50 celsius. I wanna know how to configure my OS to enable the temperature-controlled fans like the official images. The offical documents shows: Linux uses the default pwm-fan drivers to control thye fans and the device tree was defined in orange-pi-5.10-rk3588/arch/arm64/boot/dts…

Hi Guys, Here is my requirements for an electron app running Armbian OS on orangepi5 plus to support: Need GPU hardware acceleration to play video Need HDMI audio And possible NPU support. I really need help, I did lots of custom builds to find solution support all my above requirement and I found Armbian-unofficial_25.08.0-trunk_Orangepi5-plus_noble_edge_6.16.0-rc7_cinnamon_desktop.img. But my electron add crashes after running say 8 hrs or so, means it is not very stable for us [83833:0723/100030.362659:ERROR:ssl_client_socket_impl.cc(877)] handshake failed; returned -1, SSL error code 1, net_error -202 [83790:0723/101648.420086:ERRO…

Hi. I am not complaining. I just would like to understand why I must deactivate https://ppa.launchpadcontent.net/liujianfeng1994/rockchip-multimedia/ubuntu/ if I want watching video on Youtube. If it's needed to disable this repo for watching video. I am ok. But why I can't read video with package from this repo? https://paste.armbian.com/vaxedisuda

Is there an overlay or any other way of getting the Orange Pi 5 Plus to work with a 1024x600 display?

I've downloaded the Armbian 25.5.1 (Kernel 6.12) Home Assistant image (https://dl.armbian.com/orangepi5-plus/Bookworm_current_minimal-homeassistant), burned to microsd and rebooted the orange pi 5 plus. I burned the image to a microsd cards, inserted the microsd and did a hard reboot of the SBC. The error message is "Gave up waiting for root filesystem device."

Is there an Armbian image with home assistant that isn't minimalistic? or Is there a way to install HA on a more robust desktop armbian 25.2 image for the Orange Pi 5 Plus? I feel the orange pi 5 is robust enough to handle HA under a desktop Armbian environment than other SBCs.

i also have issues to move the system to the nvme ssd 😞 my base is the Armbian 25.5.1 with 6.1.115 (vendor kernel) image .... "copied" (usbimager) it to the sdcard and its booting ... 🙂 so I upgraded the system on the sdcard, still running 🙂 I read some posts and advices .... so I partioned the nvme with one big partition (/dev/nvme0n1p1) running armbian-install choosing option 7, (loading/upgrading bootloader to mtd ) after this i choose option 4 (boot from mtd, system on sata, usb ... ) only possible selection was /dev/nvme0n1 ... looked ok said yes to everything no Error system goes to shutdown /power off …

Hello all, I'm also bought an orange pi 5 pro :-) I have red a little bit in the Forum (after i'm bought) and I'm a little bit confused now 🙂 I'm new in the embedded (arm) world but have some knowledge from the desktop/x86 windows & linux world. my first expirience with the device was also .... intresting. I'm installed the official (orangepi.org) debian-booksworm image with the 6.1.xx kernel .... and diddnt get the network interfaces to run, and no nvme device available ... next try was with debian-booksworm image and the 5.10..xx kernel and the networks just runned and the nvme showed up. But i think for my need this kernel is…

After enabling the rk3588-hdmirx overlay in armbian-config device tree overlays, whenever I boot, I am greeted with multiple hdmirx (fdee0000.hdmirx-controller: hdmirx_wait_lock_and_get_timing HDMI pull out, return!) errors on boot. On a previous install, the hdmirx errors would block the entire boot process and it would just hang forever. I do not know the exact cause, but the issues seemed to arise after I ran this command to disable the X Display Server "systemctl set-default multi-user.target". The errors could only be resolved if I plugged in the sd card into another device and removed rk3588-hdmirx from overlays in /boot/armbianEnv.txt . …

It's been a while since I used Armbian. I have tons of ARM SBCs from a few years back because I think they're fascinating but they either wind up being too slow or just not worth using it for whatever since x86 "SBC like" boards exist and are pretty cheap. Fast forward to now and I'm doing some touchscreen development and just because of how I have things setup I needed 3 things, I2C, Interrupt capable GPIO and an actual DisplayPort. That combination of things is surprisingly hard to find. I had a couple of things on hand, (Seeed Odyssey x86, Odroid H2/H3, Rpi's, Nvidia Jetson Nano). I spent way more time than I should have trying to make each of these work, i…

After installing official Armbian_25.2.1_Orangepi5-plus_bookworm_vendor_6.1.99_xfce_desktop.img to sdcard, then to nvme all is fine, until, I do an apt update & upgrade, after that point chromium fails to run. I explored the logs to see it a failure to load chromium.conf from /etc/chromium.d/chromium.config (failed symbolic link to /etc/armbian/chromium.config). Is there a known workaround besides utilization of firefox?

I am running an unmodified Server version of Armbian Linux v6.12 (Ubuntu 24.04) on an Orange Pi 5 Plus. I need to play sounds using the headphone jack on my SBC. Unfortunately the ES8388 sound chip is not recognized, the aplay -l output is as follows: **** List of PLAYBACK Hardware Devices **** card 0: Analog [Analog], device 0: fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0 [fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0] Subdevices: 1/1 Subdevice #0: subdevice #0 The correct output on desktop systems should like this (and it was like this on Desktop Armbian). What should I do to enable the ES8388 sound chip while staying on a server OS? …

Hi, The RK3588 supports frequencies as low as 408MHz, but in armbian the minimum is 1008MHz, which makes the cpu run hotter and draw more power even when idle, compared with the OPI ubuntu version. These are the available frequencies: $ cat /sys/devices/system/cpu/cpufreq/policy0/scaling_available_frequencies 1008000 1200000 1416000 1608000 1800000 $ cat /sys/devices/system/cpu/cpufreq/policy6/scaling_available_frequencies 1200000 1416000 1608000 1800000 2016000 2208000 2400000 I want to add the missing frequencies, I tried to look in the armbian repo for dts files that contain these frequencies, but I couldn't find anything. Is is possibl…

How do I change the default desktop environment on Debian 12 startup from cinnamon to xfce4? I have installed xfce4 and it's related "goodies", added a .Xclients file containing "startxfc4" in both root and ~/ folder locations. But the unit sometimes boots back into cinnamon. I do not see anything under armbian-config to control the desktop environment or to switch between cli/gui. I recall such options under orangepi-config (at least the cli/gui switching).

I want to install jellyfin on my OrangePi 5 Plus and need OpenCL to enable HDR-SDR mapping. I tried to follow the instruction on Jellyfin's official website: Rockchip VPU | Jellyfin However, I'm stucked on the step of installing OpenCL. I also tried this: Install OpenCL on Debian and Ubuntu and Armbian for Orange Pi 5 RK3588 But no luck either. Both instruction led to broken hardware acceleration in chrome and failing to start kernal in Jellyfin. Logs from ffmpeg: sudo /usr/lib/jellyfin-ffmpeg/ffmpeg -v debug -init_hw_device rkmpp=rk -init_hw_device opencl=ocl@rk Applying option init_hw_device (initialise hardware device) with argu…

EDIT: I tried using ext4 rather than btrfs and.. somehow that solved it? I don't understand how the SSD file system would change how the bootloader is flashed because if properly flashed, the SD card shouldn't work at all, unless something has changed. Hey all, I wanted to move to the newest version of armbian (25.2.1) and for whatever reason neither `apt update && apt upgrade` nor `armbian-upgrade` (as a sanity check) worked so I wiped the SPI flash using `mtdtools` as prescribed in the forum post linked on the support page. 1) Booted from SD, installed Armbian and the bootloader. 2) Shut down, removed SD and turned on. Machine hung and never boote…

My setup includes orange pi 5 plus, Samsung NVME SSD M2 4 TB with Armbain os. 256 GB eMMC and Intel BE 200 Wi-Fi. There are no drivers for the intel BE 200 Wi-Fi or any instructions to make it work.

I have installed Armbian 25.02 via an official Armbian image for Armbian 25.02 (Debian 12) Vendor Kernel 6.1.xx, is it possible (and sane) to upgrade to Armbian 25.05 (Debian 12) Vendor Kernel 6.1.xx? If so besides downloading the new image and installing fresh what are one's options?

I would love to use Armbian Build to construct a Debian 12 Bookworm images with KDE Plasma as the windows manager. I note that KDE Plasma isn't an option in the armbian builder. I have no problem building with XFCE or Cinnamon.

Is there a list of Armbian Kernels that include EMMC support? I've tried the vendor kernel build 6.1.99, the LTS 6.12.21, and Bleeding Edge 6.14.0 to find they all lack the mmcblk0 under /dev/ , and lack overlays for it under /boot/dtb/rockchip/overlays/. I have wiped SPI and SPNOR without success.

Hi @ all, long time reader, but never managed to register. Now it is time... as I'm not able to solve this myself, kindly asking for help. I'm stuck, my Orangepi 5 plus stops boot at this: Loading, please wait... Starting systemd-udevd version 252.36-1~deb12u1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... (initramfs) What happened before? Last year I bought the Orangepi 5 plus (8GB) and went ahead, testing everything out - having incredible fun with this little box. But with a way to old/slow sd card which finally failed two or three months ago. I went ahead and wrote the A…

Since at least one week I find the system every morning with solid red led, waiting for a command in uboot. When looking at the journal messages, the last messages are always: Feb 10 23:45:01 etnas2 CRON[5176]: pam_unix(cron:session): session opened for user root(uid=0) by (uid=0) Feb 10 23:45:01 etnas2 CRON[5177]: (root) CMD (/usr/lib/armbian/armbian-truncate-logs) Feb 10 23:45:01 etnas2 CRON[5176]: pam_unix(cron:session): session closed for user root Feb 11 00:00:01 etnas2 CRON[5213]: pam_unix(cron:session): session opened for user root(uid=0) by (uid=0) Feb 11 00:00:01 etnas2 CRON[5212]: pam_unix(cron:session): session opened for user root(uid=0) by (uid=0) Feb…

Hi can anyone advise if they have come accross this issue. so somehow HDMIRX seems to be the hdmi input controller starts to freak out for no reason there is nothing plugged into it EVER and will randomly start to outpur this to console im thinking maybe the HDMIRX is faulty and want to remove it, I have tried removing it removed the DTB , decompiled and edited and removed it from DTB, tied to blacklist it but with no effect it does not stop spamming and the device [ 89.603095] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_phy_register_write wait cr write done failed! [ 89.613765] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_phy_register_write wa…

Hi, I've come from Joshua's 24.04 Server build. I was concerned that the support was dropping off as he's having a well deserved break. I've installed the latest Server build from here. https://dl.armbian.com/orangepi5-plus/Noble_current_server-kisak Works fine, have moved it to EMMC and removed the SD card. I use a USB power meter to see how much juice it uses. I noticed this build uses about 20 to 25% more when idle or under load compared to Josh's 6.1 kernel build. I am suspecting 6.12 has enabled more hardware in the OPi5+ and this is the reason. Is there a way to disable some of the HW to low…

I have built quite a few Debian12 Desktop images from github.com/armbian/build for a Debian Bookworm/XFCE/Vendor Kernel environment and noticed that recent vendor kernels do not have I2C-2.M0 as a kernel module listed within armbian-config. It appears that only two kernel modules are to be found, one being Panthos, the other involving a change in frequence of some item. This image does include I2C-2.mo: Armbian-unofficial_25.02.0-trunk_Orangepi5-plus_bookworm_vendor_6.1.84_xfce_desktop.img which includes kernel: Linux Atlas 6.1.99-vendor-rk35xx #1 SMP Fri Feb 21 18:11:03 UTC 2025 aarch64 GNU/Linux But these images do not contain the I2C-2…

I have a new Orange Pi 5 plus 16GB. Seems a pretty cool board and I want to replace my old Rpi 4 for Media center and Home assistant. I tried several distribution but can't get all my stuff working. The OPI5+ is attached to an onkio 5.1 receiver and the receiver go to a FHD TV. What is want to achieve is in Kodi 1. play video with GPU 2. libCec in Kodi to control Onkio volume 3. Passthrough audio Is there a working solution? Thank you

Hello everyone, This is my 1st post on the forum. My intention with this post is not to report a specific issue that I am running into, but more because I would like to collect info and suggestions from people with more experience than myself. I've recently received an Orange Pi 5 Plus and have spent a bit of time exploring operating systems suitable for this system and have settled on the Armbian solution. I'm a HW designer by trade, and have done some SW work, but I do not consider myself proficient in SW at all. I find my way around things, but that's about as far as it goes.... For the my planned use of the OPi5+, I will need eMMC b…

HI, On one orangepi5B, it seems not possible to have details from u-boot when starting target. The first messages on HDMI start with the kernel root@hn-orangepi5b-450:~# dmesg |head [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000] Linux version 6.12.0-current-rockchip-rk3588 (build@armbian) (aarch64-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #3 SMP PREEMPT Sun Nov 17 22:15:08 UTC 2024 [ 0.000000] KASLR disabled due to lack of seed [ 0.000000] Machine model: Xunlong Orange Pi 5 [ 0.000000] efi: UEFI not found. [ 0.000000] NUMA: Faking a node at [m…

Hi, I've been compiling my own Armbian images since 6.13-rc5, and now 6.13 and I noticed that when I compile i3, youtube videos and webgl tests don't work as great when I compile i3 with mesa-vpu as it does when I compile e.g., cinnamon. I also noticed that the suffix is not -mesa-desktop, only -desktop. Is it as per design and i3 doesn't include mesa at all, or is it some kind of bug? Thanks!

There's a strange issue with my orange pi 5 plus. When I boot into the ubuntu image, everything is fast, stable and zippy. But when I boot into the openmediavault image, it's incredibly slow. Simple operations like apt upgrade crawl. I noticed the cpu frequency is stuck at 408 MHz in htop in the openmediavault image. I ran a test. I opened another console and ran yes. Went back to htop and the frequency was still stuck at 408 MHz with one core pegged at 100% from the yes. So I fired up the ubuntu image and did the same thing. The core was at 100% but the frequency was at 2304mhz on that core. There is something wrong with the openmediavault …

Hello again, Based on the recommendations provided in a previous ticket, I have decided to attempt to build a custom image for the Orangepi 5 Plus. I read the docs provided in the link of that post and noticed that there is no mention of installing the cross complier tool chain for arm in ubuntu 22.04, which I just downloaded for this purpose. Do I need to install those tools or will that be addressed once I clone the git repo and run the compile.sh BOARD=orangepi5-plus ? Also the instructions mention Multipass and Docker, I have a Debian 12 workstation with virt-manager installed, will that work or will I need a dedicated ubuntu 22.04…

Hello Developers, I ran into some issues installing the latest release on an Orange Pi 5 Plus. The images I downloaded are as follows: Armbian_24.11.2_Orangepi5-plus_noble_current_6.12.0_kde-neon-kisak_desktop.img.xz Armbian_24.11.2_Orangepi5-plus_noble_vendor_6.1.75_gnome-kisak_desktop.img.xz The KDE version will install and boot from the 256GB emmc drive, however it only works if there is a 4K HDMI monitor attached to HDMI1, I was not able to get it to display on a 1920x1200 HDMI monitor nor a USB connected or HDMI connected portable display (2560x1440). The Gnome version will boot with any of those 4 types…

Hi Anyone else having problems with NVMe disks on the Orange Pi 5 Plus 16gb? I have a WD Black SN750 and use the original power supply, I have tried with Armbian and Ubuntu Rockchip and with both I have random failures at startup not recognizing the drive. When fail I do this tests: 08:13:33 cristian@orangepi5-plus ~ → lspci 0000:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd Device 3588 (rev 01) 0000:01:00.0 Non-Volatile memory controller: Sandisk Corp Device 501e 0002:20:00.0 PCI bridge: Rockchip Electronics Co., Ltd Device 3588 (rev 01) 0002:21:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8822CE 802.11ac PCIe Wireles…

I somewhat recently used Armbian Build to compile a desktop Bookworm image, which is quite stable and functional except for EMMC support. Packages: Debian stable (bookworm) Support: DIY (custom image) Linux Atlas 6.1.84-vendor-rk35xx #1 SMP Tue Dec 24 13:36:04 UTC 2024 aarch64 GNU/Linux My question is where can one find the current status of the various kernel versions support for features like I2C, SPI, EMMC, MESA, etc.? I recognize that newer kernels like 6.12.yyy are very much a WIP. I also would love more information on the the RK3588 kit used with kernels to backport features.

Hi. I have the official raspberry TV hat https://www.raspberrypi.com/documentation/accessories/tv-hat.html I'm wondering if I can use it on the Orange Pi. https://pinout.xyz/pinout/tv_hat http://www.orangepi.org/orangepiwiki/images/a/ac/Plus5-img302.png

I installed latest Armbian_24.5.1_Orangepi5-plus_bookworm_vendor_6.1.43_minimal.img and I can't get wifi to work. The adapter is RTL8852BE. I installed armbian-firmware-full and the adapter is shown in lspci, but there is no wireless interface. armbian-config does not list wifi as an option. armbianmonitor -u

I'm using an Orange Pi 5 Plus 16GB SBC, with Armbian image (https://dl.armbian.com/orangepi5-plus/Bookworm_current_cinnamon-backported-mesa) which uses Kernel 6.12. I am trying to get a BME280 I2C sensor attached to the following pins of the 40 pins; 1 (3.3v), 3 (GPIO0C0), 5 (GPIO0B7), and 6 (GND). The BME280 sensor has the VIN wired to 3.3v (pin 1), SDA wired to SDA (pin 3), SCL wired to SCL (pin 5), and GND to GND (pin 6). The device should use address 0x76, but isn't listed under the four I2C buses found in /dev. This configuration worked fine when using the stock OrangePi 5 Plus Debian Bookworm image, but does not have I2C2 listed as a device under /dev un…

This is a new release of the uefi firmware for Orange Pi 5 Plus which now has mainline kernel support. My thought was that this new release would support armbian uefi builds but so far no love. Does anyone know of an armbian build that would work with this??? The is the one of the tag lines from readme.md found @ https://github.com/edk2-porting/edk2-rk3588 "It delivers a PC-like standardized boot experience, supporting multiple operating systems, such as Windows, Linux, BSD and VMware ESXi."

Desktop images with Armbian Linux v6.12 variant Cinnamon with mesa/vpu support fails to boot from SD card. The message displayed on screen is "Begin: Running /scripts/init-premount ... (initramfs) _" SPI was erased, and the minimal install have no issues booting from a sd card. The SBC is an Orange Pi 5 Plus with 16gb ram

Not an issue nor a bug nor a trouble abour my Orange pi or Armbian. I wanted to build my "own" armbian for educational purpose. I mean to raise my knowledge. I followed this page. https://docs.armbian.com/Developer-Guide_Build-Switches/ however since it's done. I'm looking for about how to make the *.img file or if I can use *.deb located in my ~/build/output/debs I just miss these informations to finish and trying my failure compilation. I say failure compilation because "first time" is always a fail By the way, if I posted in the wrong place. Delete my post and please accept my apologies.

I have built an Orange Pi 5 Plus systems. I have a 256gb eMMC card which seems to run as speed would expect. Yet when I test the NVMe drive I get slow speeds compared to what is suggested to get. I have seen other people posts that suggest they are getting at least 4gb/s using NVME drives. I have searched for other issues but there is no errors in the logs just can't get the speeds I was expecting. I have the following which suggests at least 5gb/s KINGSTON SNV3S500G I have formatted it using Ext4. root@orangepi5-plus:/boot# hdparm -Tt /dev/nvme0n1 /dev/nvme0n1: Timing cached reads: 2804 MB in 2.00 seconds = 1404.10 M…

I connected a 49" super wide curved monitor (philips 49b2u5900) to opi5+ through HDMI. I would expect to have the possibility to choose between resolutions of 5120x1440 or 3840x1080. Unfortunately I only get 16:9 resolutions. v24.8.4 for Orange Pi 5 Plus running Armbian Linux 6.1.75-vendor-rk35xx Packages: Ubuntu stable (noble) david@orangepi5-plus:~$ xrandr Screen 0: minimum 16 x 16, current 3840 x 2160, maximum 32767 x 32767 HDMI-1 connected 3840x2160+0+0 (normal left inverted right x axis y axis) 1190mm x 340mm 3840x2160 59.98*+ 2048x1536 59.95 1920x1440 59.97 How can I configure the proper resolution? I as have little e…

I followed the provided instructions to install Arbmbian on Orange Pi 5 Plus 16GB, so I downloaded the official Ubuntu image from the Orange Pi website, and when it booted, it sudo apt update sudo apt install mtd-utils sudo flash_eraseall /dev/mtd0 The flash operation was finished successfully. Then I turned off, loaded Armbian Ubuntu 24.04 (Noble) (Desktop images with Armbian Linux v6.12) on SD and started the machine. I have a monitor connected to the machine, but there is no output. My router doesn't show any new network device, so I suppose that Armbian doesn't load. It's exactly the same situation when I tried to install Armbian without /dev/mtd0 erasin…

I have Orange Pi 5 Plus that I plan to install in a remote location. To boot Orange Pi, I need to press the physical Power On button. How I can setup the machine to boot automatically once the power is supplied? There is nobody on the remote side to press this button. Or maybe there are other options to boot remotely like WakeOnLAN? Where it can be configured? In orangepi-config?

I have set up Armbian 24.8.4 bookworm on my 32GB Orange Pi 5 Plus. Most everything works as expected out of the box. The second HDMI port doesn't detect the second screen, and the screen displays No Signal. I have tested the cables and monitors to ensure they are functioning. I have also ensured I wasn't plugged into the HDMI input by accident. I was about ready to proclaim it a hardware issue, but on booting the "Official" Orange PiOS Arch image, the dual monitor support worked as expected. I checked the dtb file included with the Arch image, and it has many references to HDMI0 and HDMI1 devices, while the one used by default with the Armbian ima…

Hi, last night a set of updates was installed and I rebooted the Orange Pi 5+ this morning. After the reboot I've seem to have lost the connection to the Orange Pi 5+, it is normally connected without a screen so I access it through SSH and the Open Media Vault web GUI. I've tried to connect it to a screen and then it seems to boot up just fine. Looking around with the screen connected it seems like the network cards aren't detected. My Linux skills are very limited but "sudo lshw -class network" shows nothing. One detail is that my router seems to detect it when it's connected and gives it the normal IP address that I've set in the 192.168.0.x ran…

Folks, I've got an Orange pi 5 plus up and running using Armbian, I've used the minimal install and although it's been plain sailing for the main part, no matter what I do I can't work out how to give it a static IP address (dynamic works fine). I've spent an hour trying: armbian-config, - Network | IP | Static and setting it to what I want - it ignores it and when I go back in it's gone back to 127.0.0.1 This page: https://docs.armbian.com/User-Guide_Networking/ Creates the yaml file with my interface abd required address as here: GNU nano 7.2 /etc/netplan/20-static-ip.ya…

Hi all , Just installed last supported version: Armbian 24.8.1 Noble Gnome, MESA / VPU, Kernel: 6.1.75, Size: 1.5 GB, Release date: Aug 26, 2024 I have 2 dell monitors : u2515h ultrasharp 1440p, and more modern P3424WE with 3440x1440 max resolution. With both - armbian max resolution in display settings is always 1920x1080. My previous experience here was with radxa zero D1 and 1440p was working here smoothly out of box on different armbian images. I also tried Ubuntu 22.04 (Jammy)KDE NeonMESA / VPU https://dl.armbian.com/orangepi5-plus/Jammy_current_kde-neon-kisak with same results: no resolution higher then 1080p …

Hi everyone, I just received an "orange pi 5 plus" and I wanted to use the hdmi-input feature in it. I installed armbian and added the hdmirx overlay, and now I can use ffmpeg or gstreamer to stream video input. Good. Alas, I see no alsa hdmi input card. I tried to search for some settings but didn't find any... The only information I found on this feature are here https://github.com/armbian/linux-rockchip/blob/rk-6.1-rkr3/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts do you have any pointer to give me on how to enable this feature? (I know how to compile stuff, using Linux since 1998 ) thanks …

Hi, A UEFI-ARM64 install of armbian opi5+ 24.11.0-trunk fails during armbian-install due to incorrect knowledge of partitions: root@uefi-arm64:/usr/sbin# lsblk -l NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 1 14.4G 0 disk sda1 8:1 1 256M 0 part /boot/efi sda2 8:2 1 14.2G 0 part /var/log.hdd / zram0 252:0 0 7.7G 0 disk [SWAP] zram1 252:1 0 50M 0 disk /var/log zram2 252:2 0 0B 0 disk nvme0n1 259:0 0 953.9G 0 disk nvme0n1p2 259:3 0 953.6G 0 part /mnt/armbian-install.NQULbp/rootfs /mnt/tmp…

I have a couple Orange Pi's, and the HDMI is broken. I noticed that many believe that it is Armbian, but it is not. Orange Pi's probably won't be where we want them until 2025. I found a couple notes from development teams, one below and one from September. Both say the same thing: essentially it's in the works: "The RK3588 SoC family integrates the newer Synopsys DesignWare HDMI 2.1 Quad-Pixel (QP) TX controller IP and a HDMI/eDP TX Combo PHY based on a Samsung IP block. Add just the basic support for now, i.e. RGB output up to 4K@60Hz, without audio, CEC or any of the HDMI 2.1 specific features." https://patchwork.kernel.org/project/linux-rockchip/pa…

Hello, I would like to have dual boot with a startup menu similar to GRUB on a PC, the idea is to have Android installed on the eMMC and Ubuntu on the NVMe, I am referring to an Orange Pi 5 Plus. Has anyone gotten it or is working on it? Thank you

Hello, I tried to install the RTL8821CE card on Orange Pi 5 Plus, but only the Bluetooth is on, the wifi not working. Which driver i should use? I am using Armbian 24.2.1 Jammy with Linux 5.10.160-legacy-rk35xx here is the dmesg of admin@orangepi5-plus:~$ nmtui admin@orangepi5-plus:~$ dmesg | grep 8821 [ 5.588211] pci_bus 0003:30: root bus resource [mem 0x9c0000000-0x9ffffffff pref] [ 8.482106] rtw_8821ce 0002:21:00.0: enabling device (0000 -> 0003) [ 8.493940] rtw_8821ce 0002:21:00.0: Firmware version 24.11.0, H2C version 12 [ 8.534600] rtw_8821ce 0002:21:00.0: rfe 6 isn't supported [ 8.534719] rtw_8821ce 0002…

I'd like to add hardware acceleration for my Orange PI 5 Plus, i've installed ` apt install -y clinfo` on the host (armbian) docker exec -it jellyfin /usr/lib/jellyfin-ffmpeg/ffmpeg -v debug -init_hw_device rkmpp=rk -init_hw_device opencl=ocl@rk ffmpeg version 6.0.1-Jellyfin Copyright (c) 2000-2023 the FFmpeg developers built with gcc 12 (Debian 12.2.0-14) configuration: --prefix=/usr/lib/jellyfin-ffmpeg --target-os=linux --extra-version=Jellyfin --disable-doc --disable-ffplay --disable-ptx-compression --disable-static --disable-libxcb --disable-sdl2 --disable-xlib --enable-lto --enable-gpl --enable-version3 --enable-shared --enable-gmp --enable-gnutls …

Hello! First time poster, long time admirer. I've been unable to get ANY of the 6.10.x images to boot off SD card (Sandisk Extreme) for the Orange Pi 5 Plus. Specific images which are not working for me: Armbian_24.8.0-trunk.472_Orangepi5-plus_noble_edge_6.10.2_gnome-kisak_desktop.img.xz Armbian_24.5.5_Orangepi5-plus_noble_edge_6.10.1_gnome-kisak_desktop.img.xz Armbian_24.8.0-trunk.472_Orangepi5-plus_trixie_edge_6.10.2_minimal.img.xz Has anybody else had better luck?

I'm trying to install https://dl.armbian.com/orangepi5-plus/Bookworm_vendor_minimal in my Orange PI 5 Plus to the emmc but I've got a black screen after removing sd card.

Hello, Long time Gentoo and Raspberry Pi user, but I am interested in a more powerful Arm device. Will buy an Orange Pi 5 plus device if it meets my requirements. I am interested about dual or multiple boot: let's say Linux and Android or, at least multiple Linux distro - let's say Armbian and Gentoo. It is possible ? On Raspberry Pi 4 with a larger boot partition I switch content of /boot from boot/debian /boot/gentoo, have multiple partition on SATA SSD connected via USB edit root parameter in /boot/cmdline.txt and that way I choose which distro to boot. On Orange PI 5 (Plus) I read that SPI chip have to be flashed to choose the boot device fro…

Updated: The Armbian vendor kernel version now includes Panthor, and will soon be able to run it as well. Waydroid images: https://github.com/WillzenZou/armbian_fork_build/releases/download/willzen-armbian-24.5.0/2.waydroid-panthorv10-240416-v1.img.tar.gz Note: Waydroid needs to be run in the Wayland desktop environment. (Such as Gnome wayland, KDE wayland session) What's work: OpenGL ES is ok, I have tested some game: Mincecrat, gameSHINE, Monument Valley 2 What's not work: Vulkan. Video hardware decode and encode. How to use Waydroid 1. To install Waydroid,…

Hi, Like the topic says, both NICs are underperforming, they are connected to a Gb switch which I use and benched with other machines, neither iperf nor iperf3 (threaded and not threaded) go higher than 700Mbps. Another server plugged on the same switch reaches Gb steadily. I applied CPU affinity so both IRQ's are handled by the A76 cores but it makes no difference. OS: Armbian 24.5.5 Bookworm, uname -a: Linux geonosis 6.1.75-vendor-rk35xx #1 SMP Fri Jul 19 14:49:03 UTC 2024 aarch64 GNU/Linux There's not much running on the board for now.

Hi all, Just want to share this issue i came across from my recently purchased OPI5+ 32GB version. I noticed it freezes when transferring .img from micro SD card to eMMC or NVMe drives via the command line. Now the img file are armbian OS and no its not the img file issue. at times I can get it to around 70seconds and it will freeze. hard reboot is required, unable to complete the transfer. I have also tried to reduce the bs=10 speed but still the same. Now i have also got the 16GB version and this works fine with no issues... Good chance there is something wrong with this latest hardware..…