Allwinner sunxi

Hello, perhaps it's a noob question, but I am a noob, sorry 🙂 I had my BTT CB1 on Armbian 24.2.3 Bookworm CLI, with a BTT HDMI 5 display attached. Display was working fine. Flashed Armbian 24.5.1 Bookworm Minimal (no CLI available on the downloads page) and the display shows absolutely nothing. Flashed Armbian 24.2.3 back, and it works again. What am I missing? armbianmonitor -u file: https://paste.armbian.com/esoboqemot

• 0

  Reputation Points

• 5 replies
• 5k views
• 3 followers

gensoloone

September 22, 20242 yr

Please help. Board: orange pi zero 2+ h5 Upgraded packages(from apt upgrade): Get:1 http://security.debian.org buster/updates/main arm64 libp11-kit0 arm64 0.23.15-2+deb10u1 [303 kB] Get:2 http://httpredir.debian.org/debian buster-updates/main arm64 tzdata all 2020e-0+deb10u1 [266 kB] Get:4 http://security.debian.org buster/updates/main arm64 nodejs arm64 10.23.1~dfsg-1~deb10u1 [87.3 kB] Get:5 http://security.debian.org buster/updates/main arm64 libnode-dev arm64 10.23.1~dfsg-1~deb10u1 [397 kB] Get:6 http://security.debian.org buster/updates/main arm64 libnode64 arm64 10.23.1~dfsg-1~deb10u1 [5,280 kB] Get:3 https://mirrors.dotsrc.org/armbian…

• 0

  Reputation Points

• 5 replies
• 4.9k views

Igor

January 11, 20215 yr

Hello, I‘m recently updated to Armbian 24.2.1 Bookworm with Linux 6.6.16-current-sunxi. The system is running fine but if I disconnect the network interface, the system gets stuck in kind of a dead loop. This behavior gave me the hint that my WiFi repeater is broken and needs to be exchanged. Anyway, the CPU temperature rises and no further interaction with the system is possible. If I disconnect it, from a normal operating switch, the OpiOne’s behavior looks the same. My problem with this behavior is that after reconnecting the network, it does not get back available, until I do a power cycle. I tried to read …

• 0

  Reputation Points

• 5 replies
• 3.8k views
• 2 followers

Stephen Graf

April 12, 20242 yr

vmlinuz-4.20.7-sunxi64 works fine (the Armbianmonitor URL is from that) but 5.1.0 breaks eth: 1c30000.ethernet: Unsupported interface mode: rgmii-txid

• 0

  Reputation Points

• 5 replies
• 4.3k views
• 1 follower

windysea

June 5, 20197 yr

After upgrading from 4.14.70-sunxi64 to 4.19.13-sunxi64 Pine64+ board started to misbehave after running for some time. Dmesg shows: Armbian-release: BOARD=pine64 BOARD_NAME="Pine64" BOARDFAMILY=sun50iw1 VERSION=5.70 LINUXFAMILY=sunxi64 BRANCH=next ARCH=arm64 IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image With Armbian Pine64 3.10 kernel board worked without hanging for 2+ years. I also tried 4.18.xx-sunxi64 kernel from dev branch - same problem.

• 1

  Reputation Points

• 5 replies
• 5.1k views
• 3 followers

Aurimas

July 11, 20197 yr

I'm hesitant to post this here, because I am not really sure that this is an armbian issue to begin with. But I'm somewhat stumped. During the build process I configured the kernel to enable real time threads. CONFIG_NO_HZ_COMMON=y CONFIG_HZ_1000=y CONFIG_HZ=1000 CONFIG_PREEMPT_RT=y However, as I started to migrate my development I discovered I couldn't create a real time thread. So I pulled down areal time test suite (https://wiki.linuxfoundation.org/realtime/documentation/howto/tools/rt-tests) And confirmed it has the same issue: Unable to change scheduling policy! either run as root or join realtime group I am …

• 0

  Reputation Points

• 5 replies
• 3.5k views
• 1 follower

jgauthier

April 13, 20251 yr

I have a Pine64+ 2GB and use Waveshare 3.5 (A). Armbian Bionic Ubuntu installed. I tried to initiate Waveshare screen by following steps: - Enable spidev0.0 from armbianEnv.txt (confirm with /dev/spidev0.0) - modprobe fbtft by: sudo modprobe fbtft_device name=piscreen But I got error with step 2. Here is the output of dmesg [ 4419.154174] fbtft: module is from the staging directory, the quality is unknown, you have been warned. [ 4419.163004] fbtft_device: module is from the staging directory, the quality is unknown, you have been warned. [ 4419.164436] spidev spi0.0: spidev spi0.0 1000kHz 8 bits mode=0x00 [ 4419.164564] spidev spi0.0: Deleting s…

• 0

  Reputation Points

• 5 replies
• 4.3k views

icce

January 21, 20197 yr

Hello, I am wondering what is the current status of wifi on Orange Pi Zero 2? Is it working? If yes then on which release? If not then what are the current problems related to this? Is somebody working on it? How one could help to make it working? I am asking because I am a little bit confused because of this This topic is more than 2 years old but I see no update.

• 1

  Reputation Points

• 5 replies
• 9.1k views
• 2 followers

Kiendeleo

January 10, 20233 yr

Old ugly EOL-kernel legacy image received fixes for booting. Feel free to test. https://imola.armbian.com/dl/orangepizero2/archive/

• 0

  Reputation Points

• 5 replies
• 5.8k views
• 2 followers

Werner

June 1, 20233 yr

LCD support does not appear to be working in the latest builds (stable kernel 5.8.6, development kernel 5.9.7) My understanding is that this has been an issue for a while with A64 boards, specifically the Pine64, but that it was working at one time. Here's what I've tried so far: -Followed instructions at https://docs.armbian.com/Hardware_Allwinner/ and added "setenv video-mode sunxi:480x272-24@60,monitor=lcd,hpd=1,edid=1" to boot.cmd and put "saveenv" at the end, re-compiled boot.scr -Did a modprobe of panel-olimex-lcd-olinuxino -Rebooted several times -Ensured that LCD jumper was closed and verifie…

• 1

  Reputation Points

• 5 replies
• 4.1k views
• 1 follower

Digitalman1983

November 24, 20205 yr

It looks like the May 28th release produced issues. I tried using the images on the OrangePI Zero 2 and the led only stays red. The prior version worked with no issue.

• 0

  Reputation Points

• 5 replies
• 6.3k views
• 1 follower

Dominik

August 14, 20224 yr

Hoping someone can help me out. When I use the desktop images from the following page: https://www.armbian.com/bananapi-m4-zero/, I get my display properly identified (connected via HDMI) and can change resolution, rotation, etc. However, as with noted in other posts, these do not have WiFi. In order to get WiFi working, I use the image from here: https://docs.banana-pi.org/en/BPI-M4_Zero/BananaPi_BPI-M4_Zero. For my needs, this image works fine with the one exception. It does not detect the display and only shows default with no ability to change settings. I have poked around and tried to find a solution but am coming up empty. Is there so…

• 1

  Reputation Points

• 5 replies
• 3.6k views

AryasDad

January 3, 20251 yr

I couldn't find a topic with this device, although support is announced, so I'm posting here. To moderators: please create an appropriate section. How to unlock UART1 and UART2 on this device?

• 0

  Reputation Points

• 5 replies
• 4.8k views

AlexNVZ

October 15, 20232 yr

Hello, today I made an upgrade of my pine64-mainline and failed miserably - my new armbian image won't boot any more. So I did some more tests with a new more different sd-cards, power supply and the mailine kernel form the download site (https://dl.armbian.com/pine64/Ubuntu_xenial_dev_nightly.7z): Again, the same behaviour, the image doesn't bott any more after "apt update" and "apt upgrade". Please, could someone help me with this problem? I hope these lockup logs help in troubleshooting. Thanks a lot! boot-fail-2017-09-06-A.log boot-fail-2017-09-06-B.log

• 1

  Reputation Points

• 5 replies
• 4.5k views
• 2 followers

Menion

September 11, 20179 yr

Hello all, i have some trouble with my CB1 and perhaps any of you know a solution :). I want to use the "Spoolman", a Database to watch my Filaments for 3d Printers. All my pi´s are currently in use, so i took a BTT CB1 i never touched since i got them with one of my voron Printers xD. I installed Armbian Server os i downloaded from this page, installed it and can connect with putty. I installed Spoolman and tried to connect to the PI with my Browser, but i cant reached the "Website". So i can ping from the PI into every other client into my LAN. I can ping my PI from every Client in my LAN. …

• 0

  Reputation Points

• 5 replies
• 4k views

webs

September 27, 20242 yr

Orange pi zero plus 'shutdown -r now' shuts down, won't reboot within 20 minutes. Have to power cycle. reboot worked initially. I installed a few bits and firefox. Not sure what triggered it. In other reports I read kernel upgrades. Could it do a lengthy fsck during boot? 64 GB SD-card/file system. Would some (red or green) LED shine? It's all dark.

• 0

  Reputation Points

• 4 replies
• 7.1k views

schwar3kat

April 14, 20224 yr

Hi everyone I just want to ask a question, Im using Miktver 7 inch HDMI touch screen lcd and Orange Pi one. The hdmi port and touch port connects fine to the orange pi one but the touchscreen not responding, but when I connect the Miktver to my laptop the touchscreen is responding. My question is what should I do to have touchscreen response to the orange pi one? The OS that i use is android 4.4.2

• 0

  Reputation Points

• 4 replies
• 3.5k views
• 2 followers

Jose Fernando Babasa

October 14, 20232 yr

Hi, I just installed the Armbian on a Pine A64+ (Armbian Focal, mainline based kernel 5.9.y). I'm having trouble getting audio from the 3.5mm stereo output. I've tried several things, including a speaker test: speaker-test -c 2 -Dsysdefault:sun50ia64audio I tried editing /etc/asound.conf but it doesn't seem to affect anything. Do changes to that file apply instantly? What can I do to test/diagnose the issue?

• 0

  Reputation Points

• 4 replies
• 5.2k views
• 1 follower

Pander

August 28, 20224 yr

Hi, I've tried to change the default console from ttyS0 to ttyS3, using the mainline kernel but I don't get it to work. Modifying boot.cmd I managed to change the tty's baudrate like this: "if test "${console}" = "serial" || test "${console}" = "both"; then setenv consoleargs "${consoleargs} console=ttyS0,38400"; fi" after recompiling with "mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr" it gave me an 38400-baud-output begining with line "Loading, please wait...starting version 229" But changing the settings to use ttyS3 does not work at all: "if test "${console}" = "serial" || test "${conso…

• 1

  Reputation Points

• 4 replies
• 3.4k views

linda

July 9, 20179 yr

I just received my Pine A64 LTS V1.2 board, 7" LCD TOUCH SCREEN PANEL, and playbox enclosure. I flashed an sd card with Linux Armbian Focal: https://dl.armbian.com/pine64so/Focal_current If the LCD is connected via the DSI port, the boot freezes during UBoot. If I disconnect the LCD from the DSI connector, we get past the first part of UBoot immediately and it eventually brings me to the login prompt. I do observe that the green power LED appears to light then turn off about when it freezes on boot with the DSI connector attached. I have the official 5 V 2 A SOPINE supply from the store (https://store.pine64.org/product/sopine-baseboard-us-p…

• 0

  Reputation Points

• 4 replies
• 3.8k views
• 1 follower

mudcat

August 9, 20206 yr

I am using Armbian Buster on Pine64-LTS units. I recently upgraded version 19.11.3 to 20.02.1 and since having problems with high kworker load and strange warning in dmesg output: [ 7.734729] ------------[ cut here ]------------ [ 7.737084] WARNING: CPU: 1 PID: 30 at drivers/clocksource/arm_arch_timer.c:360 sun50i_a64_read_cntpct_el0+0x24/0x30 [ 7.738928] Modules linked in: cpufreq_dt realtek axp20x_usb_power industrialio pinctrl_axp209 dw_hdmi_cec lima dw_hdmi_i2s_audio gpu_sched dwmac_sun8i mdio_mux [ 7.741485] CPU: 1 PID: 30 Comm: kworker/1:1 Not tainted 5.4.20-sunxi64 #20.02.1 [ 7.743435] Hardware name: Pine64 LTS (DT) [ 7.745514] Wor…

• 0

  Reputation Points

• 4 replies
• 5k views

Patrick Peters

February 8, 20215 yr

@Igor What is the status of the orangepione? On the download page there are no images presented yet in the build framework is shows up as "conf" in the support (1st) page.

• 0

  Reputation Points

• 4 replies
• 2.8k views
• 1 follower

Stephen Graf

February 5, 20242 yr

I can't boot orange pi zero 2 from first use... It displays only red LED and it doesn't change. I connected lan, SD card and power source. What is wrong with my orange pi?

• 0

  Reputation Points

• 4 replies
• 12.1k views

jscax

September 15, 20224 yr

SOURCE: https://github.com/MathiasStadler/orange-pi-zero-boot-from-spi I spent the whole day trying to boot without a microSD, and I finally got it, using the Orange Pi Zero SPI boot tutorial, with a few adjustments. First of all, you’ll need a microSD card. I used this Armbian version Armbian_24.11.1_Orangepizero2_noble_current_6.6.62_minimal.img.xz Once the system has booted from the microSD: sudo apt update && sudo apt upgrade -y reboot After the system reboots, we need to check if the SPI flash is detected: cat /proc/mtd #It should return something like: dev: size erasesize name mtd0: 00200000 00001000 "spi0.0…

• 0

  Reputation Points

• 4 replies
• 10.3k views

Guest

August 13, 20251 yr

a device hooked up on the microusb OTG port does not power up anymore (webcam, used to work a long time ago then I did system update but did not configure the webcam again, until now...) bruno@orangepione:~$ sudo cat /sys/kernel/debug/gpio [sudo] password for bruno: gpiochip0: GPIOs 0-223, parent: platform/1c20800.pinctrl, 1c20800.pinctrl: gpio-15 ( |orangepi:red:status ) out lo gpio-166 ( |cd ) in lo ACTIVE LOW gpio-204 ( |usb0_id_det ) in lo IRQ gpiochip1: GPIOs 352-383, parent: platform/1f02c00.pinctrl, 1f02c00.pinctrl: gpio-354 ( |us…

• 0

  Reputation Points

• 4 replies
• 3.9k views

bschwand

January 11, 20242 yr

Hi! I'm using the Sopine A64 Armbian Buster image version 5.91 in combination with my PineA64-LTS SBC. First off I'd like to say that it runs great, thank you guys very much for providing this fully featured image and thereby keeping this SBC up to date! For the last few weeks I've been trying to get the Pine 64 7" LCD screen to work with it, but so far unfortunately I haven't been able to. What I've tried: Follow instructions to get LCD working as stated on the older brother's PineA64 page: add 'pine64_lcd=on' to /boot/armbianEnv.txt, and add 'gt9xxf_ts' to /etc/modules, then reboot. No luck. Read about the Allwinne…

• 0

  Reputation Points

• 4 replies
• 6.1k views
• 1 follower

jeanrhum

November 20, 20205 yr

Hello. I'm a bit confused, i have a PINE64 board ("PINE A64+", 2GB mem.) (this one : https://www.pine64.org/?product=sopine-a64-baseboard-combo) I installed some years ago ARMBIAN on it - everything is running fine. But i'm still on kernel 3.X something : ``` uname -a Linux pine64 3.10.107-pine64 #2 SMP PREEMPT Fri Feb 8 10:23:10 CET 2019 aarch64 GNU/Linux cat /etc/armbian.txt ------------------------------------------------------------------------------- Title: Armbian 5.73 Pine64 Debian jessie default Kernel: Linux 3.10.107 Build date: 28.01.2019 ... ``` …

• 0

  Reputation Points

• 4 replies
• 5k views

Igor

September 18, 20206 yr

This is my DTS file for OrangePi Zero2, opened UART5 for attach a GPS module on GPIO. Tried to add 1wire, PPS and SPI , but can't work. maybe help someone. sun50i-h616-orangepi-zero2.dts

• 0

  Reputation Points

• 4 replies
• 5k views

Guest

December 4, 20241 yr

Hello. Because of bad CB1 eMMC board manual, and very incompetent and formal tech support (they approve that their boards can only be used for 3D printers🤦🤣) I don't understand, what pins (GPIOs) of CB1 eMMC board are used for I2C and SPI interfaces. And what pins will correspond to I2C and SPI interfaces in armbian-config -> System -> Hardware? I tried to test the board with the Pi4b_Adapter, but as I understood from pinout in the manual for the adapter (the pins for I2C 3 and 5) don't work with CB1 (NC - not connected), it works only with CM4. Does anyone know what other I2C pins are exposed on the adapter board? I plan to use the CB1 board as a platform for …

• 0

  Reputation Points

• 4 replies
• 5k views
• 1 follower

Maksim Davletchin

October 1, 20242 yr

The notes here, https://www.armbian.com/pine64/ talk about a beta image that has hardware acceleration enabled for the pine64. Unfortunately, the link is no longer valid. Anyone have a link to images I can use with the pine64 that have hardware (2d primarily) that i can use?

• 0

  Reputation Points

• 4 replies
• 3.3k views

zador.blood.stained

April 9, 20179 yr

I have tried searching but there doesn't seem to be much info on PPS support. It is a standard part of modern kernels and should be pretty consistent. On a Pine64+ using mainline kernel (debian-stretch-next) I chose an interrupt-enabled pin (PH9) updated /boot/armbianEnv.txt with overlays=pps-gpio uart1 uart2 param_pps_pin=PH9 and rebooted. I have a device (a GPS) with its PPS output connected to the Pi2 bus pin 13 that corresponds to PH9 and during boot this appears to be configured as a new PPS source: [ 5.548061] pps pps0: new PPS source pps@0.-1 [ 5.548135] pps pps0: Registered IRQ 145 as PPS source /dev/pps0 is indeed created by udev…

• 0

  Reputation Points

• 4 replies
• 4.7k views
• 1 follower

reg.swensen

July 19, 20188 yr

Everytime i reboot and/or turn-off both of my Pine A64, they dont boot again until i manually turn-off/on them a lot of times, is there any fix to it? the img i use is: Armbian_5.35_Pine64_Debian_jessie_default_3.10.107.img

• 0

  Reputation Points

• 4 replies
• 2.5k views

barart

February 7, 20188 yr

When assembling custom image through armbian build env, how to insert my own config. How to enable support for booting from USB flash? To flash the bootloader in spi-flash I'm flash u-boot-sunxi-with-spl.bin into spi-flash, but have error No Bootable media found. Sorry for my English

• 1

  Reputation Points

• 4 replies
• 16.9k views

going

January 29, 20233 yr

I am trying to port my app running on legacy OS to Mainline OS and found some problems: I was able to replicate problem with following actions: 1) git cloned fresh copy of source to new directory - OK 2) edited config-default.conf: KERNEL_ONLY="no" KERNEL_CONFIGURE="no" CLEAN_LEVEL="make,debs,oldcache,images" DEST_LANG="en_US.UTF-8" BOARD="pine64so" BRANCH="next" RELEASE="xenial" BUILD_DESKTOP="yes" KERNEL_KEEP_CONFIG="no" # do not overwrite kernel config before compilation EXTERNAL="no" # build and install extra applications and drivers EXTERNAL_NEW="prebuilt" …

• 0

  Reputation Points

• 4 replies
• 5.3k views

mikebargauan

March 1, 20188 yr

Hi al!! I managed to find img with which my OPi Zero 2 starts, it's Armbian_22.02.2_Orangepizero2_focal_legacy_4.9.255. But it stops load after first `apt upgrade`. I've freezed kernel with armbian-config. Now I want to use wireguard + nftables. But everytime i'm trying to set wg up I've message: [#] nft -f /dev/fd/63 /dev/fd/63:1:1-26: Error: Could not process rule: Operation not supported ... Quick google search showed something concerning nf_tables module in kernel or something like this. (I'm not an experienced linux user). Is there any chance to set up my OPi Z 2 with wg + nftables? Thanks.

• 1

  Reputation Points

• 4 replies
• 5k views

Igor

August 30, 20224 yr

Just tried the latest image for Orangepi Zero2, the Armbian Focal Image(Armbian_22.02.2_Orangepizero2_focal_edge_5.16.11.img Built March 7 2022) The board has startup issue, the serial output seems to load some files in wrong format: U-Boot SPL 2021.10-armbian (Feb 26 2022 - 17:45:38 +0000) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.6(debug):510155aa-dirty NOTICE: BL31: Built : 17:45:34, Feb 26 2022 NOTICE: BL31: Detected Allwinner H616 SoC (1823) NOTICE: BL31: Found U-Boot DTB at 0x4a082570, model: OrangePi Zero2 INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP305 on …

• 1

  Reputation Points

• 4 replies
• 6.8k views

Gunjan Gupta

December 29, 20232 yr

Hi, I would like to use st7735 in an orangePI zero 2 (H616). The st7735 module was purchased at the following link: https://it.aliexpress.com/item/33031122936.html?spm=a2g0o.order_list.order_list_main.32.c5eb36966Y6eGs&gatewayAdapt=glo2ita Armbian usage. I connected st7735 in the following way: OPI --------> st7735 23 --------> SCK 19 --------> SDA 24 --------> CS 13 --------> AD 11 --------> RTD 4 --------> VCC 25 --------> GND I then ran the following command: sudo modprobe fbtft_device custom name=fb_st7735r gpios=dc:3,reset:0 speed=16000000 rotate=90 The screen stays white with a red stripe at the bo…

• 0

  Reputation Points

• 4 replies
• 4.7k views

konsD

March 20, 20251 yr

Hi all, I've read on the forum that support for usb gadget using the µ-usb port on the libre computer tritium needed a kernel reconfigure & recompile. I tried to start with that, but during configuration, I've seen full support already. So, was it supposed to just work ? I target armbian buster server variant. my need is to use IP over an usb (and power) cable between a linux machine (x86 and then arm) and a tritium h5 Thanks in advance

• 0

  Reputation Points

• 4 replies
• 6k views

usual user

July 5, 20206 yr

(One liner added later : the problem turned out to be the Cisco SOHO switch. They're "broken from the factory". Not what you'd expect, normally or in particular from Cisco.) Hi, everyone. I've taken the liberty of posting here with regard to my problem as I have the understanding the PINE64 forums proper are run by crazy people; my thought being to stay away from there. So, I have a 1 GB PINE64. I have ethernet performance problems - but NOT, I believe, in any way related to the early production models with their hardware fault or with gigabit ethernet being flakey. My PINE64 is in fact connected to a 100mbit hub, and is …

• 1

  Reputation Points

• 4 replies
• 3.7k views

tkaiser

June 11, 20179 yr

I'm guessing it wasn't intentional that the current legacy Armbian_5.30_Pine64_Ubuntu_xenial_default_3.10.105 image for the pine64 wouldn't work without the battery? Because the "Warning: Low battery power, shutting down to recharge" line (10th line from the end) is an absolute corker (or should I say showstopper?) when there is no battery connected to the pine64! It fell over on a 2G pine64 board that I was about to build up with Armbian. Spoiler HELLO! BOOT0 is starting! boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f boot0 version : 4.0.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0…

• 1

  Reputation Points

• 4 replies
• 3.7k views

zador.blood.stained

July 31, 20179 yr

Hi, Armbian gurus. I tried latest Armbian image for PineH64-b. (Armbian_20.11_Pineh64-b_focal_current_5.8.16_desktop) And I surprisingly found there is no audio device when I looked around.( by #aplay -l ) Is this expected for now? My older 5.6 kernel has HDMI device at least. I tried search audio problem around but had no discover so far. Please allow me to confirm with you. I'm looking for a good 5.8 multimedia-capable kernel to merge with my gentoo rootfs. Thank you.

• 0

  Reputation Points

• 4 replies
• 3.2k views

Pander

August 28, 20224 yr

Hello , i have used now for some year armbian for this board, very many thanks for that; lately have updated to newer version Debian Trxiie and found that "htop" report a higher CPU usage after freshboot (around 50%) whereas previously it sat a 10% probably; now when evoking htop it gives (CPU offline for core 2-3-4) also nproc report "1" instead of "4"=? not sure if this an error ; noticed a similar report of nproc also with a build of volumio; thank you very much;

• 1

  Reputation Points

• 4 replies
• 2.1k views

kapqa42

August 28Aug 28

Fresh install on the latest image (Armbian_25.2.2_Bigtreetech-cb1_bookworm_current_6.6.75_minimal.img.xz). First thing I wanted to do was an armbian-upgrade, but: Hit:1 http://deb.debian.org/debian bookworm InRelease Hit:2 http://deb.debian.org/debian bookworm-updates InRelease Hit:3 http://security.debian.org bookworm-security InRelease Hit:4 http://deb.debian.org/debian bookworm-backports InRelease Hit:5 https://github.armbian.com/configng stable InRelease Hit:6 https://netcup-02.armbian.com/beta bookworm InRelease Reading package lists... Done W: Target Packages (main/binary-arm64/Packages) is configured multiple times in /etc/apt/sources.list:1 and /etc…

• 0

  Reputation Points

• 4 replies
• 2.4k views
• 1 follower

Paul Damian

May 14, 20251 yr

Hello. I am taking the task of organizing and performing the BTT Pi and CB1 support update. The plan is to use mainline kernel 6.6 and 6.8 (basically the default sunxi64 config) instead of the BTT fork and use patches to backport kernel patches for drivers and hardware support. The Jira issue is AR-2312, which is a collection of things that will need to be done for this initiative. @Gunjan Gupta @c0rnelius @ag123 @jernej @ALIGMSTEN I'm asking for your help on this, as Igor has said to me that you are more knowledgeable on the state of the board and what it needs. From what I've found, there has been a PR that upgraded the kernel used for BTT CB1 to 6.1.79 using patch…

• 1

  Reputation Points

• 4 replies
• 7.7k views
• 1 follower

JohnTheCoolingFan

May 20, 20242 yr

I am using an armbian build image on PINE A64+ board with the kernel 3.10.107. During build i enabled below I2S driver as built-in. CONFIG_SND_SOC_SUNXI_RW=y CONFIG_SND_SOC_SUNXI_AUDIO_DMA=y CONFIG_SND_SOC_SUNXI_TDM=y CONFIG_SND_SUNXI_SOC=y CONFIG_SND_SOC_INTERNAL_AUDIOCODEC=y CONFIG_SND_SOC_INTERNAL_I2S=y CONFIG_SND_SOC_AUDIO_CODEC_MACHINE=y CONFIG_SND_SOC_DAUDIO_PLATFORM=y CONFIG_SND_SOC_VIRCODEC=y CONFIG_SND_SOC_DAUDIO0_MACHINE=y # CONFIG_SND_SOC_DAUDIO1_MACHINE is not set CONFIG_SND_SUNXI_SOC_HDMIAUDIO=y The Internal Audio and HDMI Audio are initialized successfully but failed to snddaudio0 which can be accessed from Euler bus…

• 0

  Reputation Points

• 3 replies
• 4.4k views
• 2 followers

gkkpch

December 17, 20187 yr

Hello, I have an issue, i am running the Pine LTS board on eMMC using Armbian latest stable image. We want to access the serial port on the board, so to test i downloaded putty, i select serial and click open. I get an error when opening this, so i have to run: sudo chmod 777 /dev/tty50 and sudo chmod /dev/tty52 on each boot, then i am able to open the serial port using putty. When i look at the ls -l /dev/tty50 i get: crw--w---- 1 root tty 4, 50 Jan 30 30 16:07 tty50. After etensive research i added my user cst to the tty group, but when i reboot i still have to manually run chmod again to access the serial port. Can someone please …

• 0

  Reputation Points

• 3 replies
• 4.5k views

Matthew Harding

January 31, 20197 yr

By following the instruction how to enable ili9486 on orange pi, I have tried to do that with pine64. So, I installed armbian focal 22.10 with 5.15 kernel, enabled spidev and overlayed dts with tft installation and initialization. But still have a white display. Also I was trying another way to use/edit fbtft, the same issue. `dmesg` shows that spi driver no compatible with ili9486

• 0

  Reputation Points

• 3 replies
• 3.2k views
• 2 followers

robertoj

January 21, 20251 yr

Thanks for everyone's work on this project! I'm working on a few Orange Pi Zero 2 v1.5's, and they won't finish booting on a few of the most recent images. (Just testing jammy right now to keep things consistent) Boot Successfully: Armbian_22.11.3_Orangepizero2_jammy_edge_6.1.4 Armbian_22.05.3_Orangepizero2_jammy_edge_5.17.11 Do Not Boot Successfully: Armbian_23.02.2_Orangepizero2_jammy_edge_6.1.11 Armbian_22.11.1_Orangepizero2_jammy_edge_6.0.10 Armbian_22.08.7_Orangepizero2_jammy_edge_5.19.16 Typically, when the boot fails, all I get is this over serial with no LED's: U-Boot SPL 2022.07-armb…

• 1

  Reputation Points

• 3 replies
• 5.3k views
• 1 follower

ALIGMSTEN

March 1, 20233 yr

Suddenly the 6.16 kernel was released in apt , who did it? why all overlays missed?

• 0

  Reputation Points

• 3 replies
• 2.5k views

Werner

August 18, 20251 yr

I'm trying to connect Nokia 5110 / PCD8544 LCD to my Orange Pi One H3 (Board v1.1). This is my wiring: Connection (LCD to OPi) Nokia 5110 LCD pin Orange Pi One pin GND GND LIGHT GND VCC 3.3v CLK PC2 (CLK) DIN PC0 (MOSI) DC PA6 CE PC3 (CE) RST PA9 This is my LCD: The backlight is working upon turning on OPi One. The official Orange Pi One H3 manual suggests…

• 1

  Reputation Points

• 3 replies
• 1.8k views

heltheowl

June 29Jun 29

Hello, I have orange pi zero 2 but it doesn't work with armbian versions after kernel version 4.9.318, I tried many versions. When I check it through the serial port, it stays on "trying to boot from MMC1 armbian" and the led on it is constantly red. Also, if I upgrade the kernel with apt-get upgrade in version 4.9.318, the card does not boot afterward and gets a "No ethernet found" error. Versions I tried : Armbian_22.11.3_Orangepizero2_jammy_legacy_4.9.318.img [Worked but no wifi connection] Armbian_22.02.2_Orangepizero2_bullseye_legacy_4.9.255.img [Works good] Armbian_22.08.7_Orangepizero2_jammy_edge_5.19.16.img [Not working !!] Armbian_…

• 0

  Reputation Points

• 3 replies
• 4.3k views
• 4 followers

Darius82

March 7, 20233 yr

Hi. I am getting a kernel Oops in the Pine64+ . . . .see below. Kernel is 5.8.13-sunxi64. It was installed after a recent update. I would like to drop back to the previous kernel if possible. Does this seem like a reasonable search term for a suitable kernel? Any ideas on searching and installing a previous kernel appreciated. sudo apt-cache search kernel 5.8* | grep sunxi64 linux-dtb-current-sunxi64 - Linux DTB, version 5.8.13-sunxi64 linux-dtb-dev-sunxi64 - Linux DTB, version 5.9.0-rc7-sunxi64 linux-dtb-legacy-sunxi64 - Linux DTB, version 5.4.62-sunxi64 linux-headers-current-sunxi64 - Linux kernel headers for 5.8.13-sunxi64 on arm64…

• 0

  Reputation Points

• 3 replies
• 4.7k views

Igor

October 7, 20206 yr

So there is some weirdness happening with Armbian on the Orange Pi Zero 2 that I bought from Amazon. These are the V1.5 version of the hardware. With the Orange Pi image (which looks strangely like armbian), once the device is booted, the red led goes off, and the green led turns on. With the armbian image, the red light stays on, and the HDMI output does not turn on in the CLI image. This led me initially to think this board was not working. Once I hooked up a USB to Serial interface, I noticed it booted. Well, at least when the SD card was seated correctly, but that is a hardware problem. Once booted, `armbian-config` does not show the wif…

• 0

  Reputation Points

• 3 replies
• 3.5k views
• 1 follower

ALIGMSTEN

January 10, 20233 yr

any one have a succes with? using Armbian_25.2.2_Bananapim4zero_noble_current_6.6.75.img wifi not work, thats fixed with: overlays=bananapi-m4-sdio-wifi-bt Applying kernel provided DT overlay sun50i-h616-mcp2515.dtbo failed on fdt_overlay_apply(): FDT_ERR_NOTFOUND and then: Error applying DT overlays, restoring original DT and have no wifi and any overlays at all.. on a bpi 2W Zero runs double mcp2515 on a spi1 as can0 + can1, but on M4 zero - no success at all, everythings are tried, all armbian builds, trying self writed overlays, tried boot from uSD, emmc - no success. always took this…

• 0

  Reputation Points

• 3 replies
• 2.9k views

Netcrusher

December 26, 2025Dec 26

Hey Igor and fellow Armbian forum members! I have worked with Armbian on my OPi PC and used the rtl8192cu-fixed github replacement driver, and recently just edited /etc/modules to include 8192cu(btw apt-get upgrade breaks this). However on my Pine64, dmesg says: rtlwifi/rtl8192cufw.bin isn't available. I have tried manually placing the Debian .bin file into the proper /lib but haven't been able to get the wlan0 to show up under iwconfig(yea I have already enabled it in /etc/network/interfaces. lsusb and lsmod both show some entries for 8912cu. Thanks for any insight, and let's hope we can fix this so that people can use their wifi adapters soon .

• 1

  Reputation Points

• 3 replies
• 5.3k views

pfeerick

November 23, 20169 yr

On the latest image (25.2.2) of both Server - Noble and Desktop - XFCE - Bookworm, the wireless interfaces show up as expected and connect to wifi. After the first apt upgrade and reboot, the system no longer detects the wireless interface at all. For my armbianmonitor output, there is a mediatek wireless interface plugged into USB, but there is no mention of the rtl8189 in any of the boot or hardware logs. Did something change in the overlay or other pre-kernel bootloader configs which disable the device? I would think if it were merely kernel / driver related, the hardware would still show up, but be unusable until a driver was configured.

• 0

  Reputation Points

• 3 replies
• 4.5k views
• 3 followers

Paul Damian

May 14, 20251 yr

Hi team, There are no current images for Orange Pi Zero 2 at https://www.armbian.com/cf7stdb-entries/orange-pi-zero-2/ The Zero image does not work. I did manage to find an archived legacy image based on some posts from 2022 however nothing on the new kernel works. My question is this: Is there a reason why these devices require unique builds? I understand the kernel drivers may not be in 6.x for this board however I'm more referring to the huge number of builds that need to be supported. Thanks, Jason

• 0

  Reputation Points

• 3 replies
• 7.1k views
• 1 follower

stallion25

April 4, 20233 yr

The stable armbian Focal image with Kernel 5.16.y fails to initialize the board. If I install the kernel 4.19.y image it does work in both Focal and Bullseye but when I try to change the kernel from armbian -config then it installs but on reboot it fails once again to reinitialise the board. I am using an orange pi zero 2 1gb. Just a couple of days ago Orange pi released two new images (Bullseye and Focal) with kernel 5.16 and 5.13 respectively. They do work and install. Although I would prefer to use armbian to the orange pi versions of it. Maybe someone can have a look at those two images to compare them with armbian to see where do they differ and why on…

• 0

  Reputation Points

• 3 replies
• 4k views

qiurui

May 29, 20224 yr

I am trying to display a bootlogo.bmp on boot without success. HDMI and also LCD. I don't mean the four tuxes (pines) on kernel load, i want to display it from u-boot. I am using Armbian 5.26 (don't know why kernel is 3.10.104), upgraded from 5.25. I have placed bootlogo.bmp on /boot but still nothing displayed by u-boot. All my u-boot builds also fails to display it. Has anyone tried it with success?

• 0

  Reputation Points

• 3 replies
• 3.3k views

Igor

June 12, 20179 yr

Hi guys, I've been running an armbian edge image i've compiled using the build tool (armbian bookworm 6.7.12), and it's been working perfectly, with good gpu support and hdmi out working. Now this is not strictly an armbian question, but i've been wondering: is there any way to overclock that chip even slightly? There doesn't seem to be a single post about that that i could find specifically for the H616? Any and all answers welcome!

• 0

  Reputation Points

• 3 replies
• 4.3k views
• 1 follower

nick gelinas

April 25, 20242 yr

I built an Ubuntu current image, as of commit f15f594d0bd4ad1e5d0fa412f1d25120e76e4f9a (Armbian-unofficial_26.05.0-trunk_Bigtreetech-cb1_noble_current_6.18.20.img) and started my newly arrived Pad 7 from it. Things that work out of the box: display, touchscreen, wifi, USB. Not working: LAN is not visible at all (only two wlan interfaces). Also, no audio device. According to schematics, audio is taken from HDMI output, so it should be supported by standard HDMI drivers. Where do I enable it in kernel config? https://github.com/bigtreetech/Pad7/tree/master/Hardware your hints will be appreciated. smar…

• 0

  Reputation Points

• 3 replies
• 1.6k views
• 1 follower

clackups

March 27Mar 27

How can PINE A64 GPU hardware acceleration be enabled? Playing a 24 fps full HD MP4 movie is not working smoothly. Here are some results on Armbian Jammy cli from June 30 version 22.05.3 with only installing via apt-get: - mpv, best result, probably ~10 fps - mplayer -vo sdl/fbdev2, probably ~5 fps - cvlc, probably 2~3 fps - kodi, probably 1~2 fps - gst123, could not get it running because issue with ALSA The fps are sort of guessed. Any other software and tips for testing are welcome. None of the movies playing played sound. speaker-test also did not play sound even though alsamixer showed all is well. Tips for this please too. …

• 0

  Reputation Points

• 3 replies
• 3k views
• 1 follower

Pander

October 3, 20224 yr

Unfortunately, the Orange pi zero 2 does not start with the Armbian img, it does turn on, but there is only a white line in the top left and it does not boot any further. I once downloaded the original ubuntu image from the manufacturer, this works without problems but is just outdated. Can you take a look at it? Actually wanted to install the pi hole project with Armbian Image: Armbian 22.11 Jammy Kernel 4.9.y, Size: 445Mb, Release date: Jan 10, 2023 SHA hash | PGP signature

• 0

  Reputation Points

• 3 replies
• 7.7k views

materockt

March 2, 20233 yr

Hello, I'm using a Pine 64 LTS with the SoPine image Armbian 21.02.3 Bionic with Linux 5.4.88-sunxi64 I have made various changes and installations to this image, so I want/need to continue using this image. Unfortunately, with the new hardware of the Pine 64 LTS (Pine64 LTS-V2) network connection is no longer possible. (Note: With the current SoPine image there is a network connection). Is there any way to reinstall the current network drivers in my image? I would be very grateful for any help.

• 0

  Reputation Points

• 3 replies
• 3.4k views

Alexander Ressler

April 12, 20233 yr

Hi everyone, I’m trying to get a 3.5-inch RPi display with the XPT2046 touch controller (480x320 resolution) to work on my Orange Pi One (H3). I’ve been looking for guides, but most of them are Raspberry Pi-specific and not directly applicable to the Orange Pi. Here’s what I’ve tried so far: Installed Armbian on the Orange Pi One. Connected the display via the SPI interface. Installed fbtft and tried different configurations for the screen. However, I haven’t been able to get the display to show anything or to interact with the touch input. Does anyone have experience using this specific setup? What drivers or overlays shou…

• 0

  Reputation Points

• 3 replies
• 10.6k views

robertoj

December 18, 20241 yr

Using Orange Pi zero 2 Debian bookworm minimal 24.5.1 image , I have disabled Network manager and enabled ifupdown service with static IP configuration. Linux orangepizero2 6.6.31-current-sunxi64 #1 SMP Fri May 17 10:02:40 UTC 2024 aarch64 GNU/Linux Trying to restrict ssh to listen on IP assigned to end0 only, but it is ignoring the ListenAddress 192.168.8.1:22 directive. It listens on all interfaces, which I do not want. sudo service ssh status ● ssh.service - OpenBSD Secure Shell server Loaded: loaded (/lib/systemd/system/ssh.service; disabled; preset: enabled) Active: active (running) since Thu 2024-05-30 16:10:42 UTC; 22s ago Tri…

• 0

  Reputation Points

• 3 replies
• 5.5k views

Alessandro Lannocca

June 2, 20242 yr

Over the years have been using the Pine64 2Gb computer as an automation server running with original Xenial Base Image [20161218-1] by longsleep. This is a first generation Pine64 2Gb computer that I got during the start up of the company. Currently utilizing a 2 AMP 5VDC PS connected to the Euler bus, heatsinks on the top and bottom of the board and a boot up 100Mb mode. It would run fine for months then occassionally wouldn't start on boot. Recently redid the box using Armbian. | _ \(_)_ __ ___ / /_ | || | | |_) | | '_ \ / _ \ '_ \| || |_ | __/| | | | | __/ (_) |__ _| |_| |_|_| |_|\___|\___/ |_| …

• 0

  Reputation Points

• 3 replies
• 3.1k views

Petee

April 17, 20197 yr

Armbian image version: Armbian 22.08 Bullseye Kernel 5.19.y, Size: 388Mb, Release date: Oct 22, 2022 Bug report: 1: When i reboot my orangepi zero 2 , my devices will be power off. 2: I use the newest image , display nothing on screen. But i have an older version image. It display to screen by Micro-HDMI perfect. 3: Is possible to light up green LED after system start? I mean, when the device power on, red LED light up. It's nice. But if light the green LED up after system start up, I can know my system get no troubles and it's running now.

• 0

  Reputation Points

• 3 replies
• 6.1k views
• 1 follower

tpou

December 29, 20223 yr

Looking for a working Armbian OS for Orange Pi Zero 2 seeing alot about newer images not working if anyone has confirmed working image for Running Klipper that would be appreciated Ive tried to flash both the cli images from the orange pi zero 2 section of armbian site but neither result in lights.

• 0

  Reputation Points

• 3 replies
• 5.3k views
• 1 follower

Tina

December 25, 20223 yr

Hi all, I am trying to get an OV5640 camera working on the orangePiOne. I found this thread and was wondering if the overlay (or some overlay) is still required. Without anything extra, the camera is not detected. It says that sun6i-csi and ov5640 kernel modules should be loaded, so I loaded them manually with modprobe but nothing happens and nothing is shown in dmesg. Adding the mentioned overlay with "sudo armbian-add-overlay csi-ov5640.dts" just gives me an error in dmesg at reboot time "failed on fdt_overlay_apply(): FDT_ERR_NOTFOUND Error applying DT overlays, restoring original DT" uname -a Linux orangepione2 6…

• 0

  Reputation Points

• 3 replies
• 4.2k views

bschwand

January 26, 20242 yr

Hi, Pine 64's delivery is in full swing and thousands of people are receiving/received their Pine64 boards (Mine is scheduled for May). One of the survey shows that majority of the people have chosen to install linux on their boards. Many people are struggling to find a good image for their boards and current some what stable image is based on already end of life 3.10 kernel and there is promising development by sunxi. I am sure that thousands will get benefited if they get Armbian for Pine64. So How about Armbian for Pine 64? Regards, -- Avinash

• 1

  Reputation Points

• 3 replies
• 4.4k views
• 1 follower

chrisf

June 17, 201610 yr

Hey, in lieu of a better place on the internet, I just wanted to document that the i2s overlay found here: https://gist.github.com/zuigon/65bfb73bb8a3f971774f80d3e2954adb works flawlessly with Armbian 23.08.0-trunk Bookworm with bleeding edge Linux 6.4.2-sunxi. after executing the script my PCM 5102 DAC works like a charm.

• 0

  Reputation Points

• 3 replies
• 5k views

Teddy Samsi Suwarnady

October 12, 20233 yr

As highlighted by an issue on BTT's GitHub, why are two wireless interfaces present (wlan0 and wlan1)? What should we use ? armbian-config presents them both.

• 1

  Reputation Points

• 3 replies
• 2.2k views
• 1 follower

Igor

November 18, 2025Nov 18

If someone is interested i have compiled some TSLIB deb packages for the Pine64 Touch Screen to work without evdev driver or any other service behind. Advantages: * Easy to install (if you know how to edit xorg.conf) * No service needed * No calibration needed Disadvantages: * works on X11 only Information and deb packages: https://github.com/avafinger/pine64-touchscreen Hope it can be useful.

• 0

  Reputation Points

• 3 replies
• 5k views

Learnincurve

February 14, 20179 yr

Hello! I installed a fresh Armbian (5.31; Server) on my Pine64 yesterday. Today I wanted to start playing around with GPIO ... And it seems like Pin 72 isn't working ... Doing the same on Pin 77, everything works fine ... For the secound test, I used https://github.com/databit/Pine64-CPP. I only added some Debug info to example.cpp. Spoiler Script started on Fri 28 Jul 2017 01:35:44 PM CEST root@pine64:/sys/class/gpio# echo "72" > export bash: echo: write error: Device or resource busy root@pine64:/sys/class/gpio# echo "72" > unexport bash: echo: write error: Invalid argument root@pine64:/sys/class/gpio# ls export gpi…

• 0

  Reputation Points

• 3 replies
• 3.7k views
• 1 follower

martinayotte

July 28, 20179 yr

Hello, I am new to Armbian and Linux in general. I am using an OrangePi Zero 2 (H616) board and need to enable the hardware UART. To do this, I tried using the simplest method I could find: running the command armbian-config -> System -> Hardware. However, in the section where I should find options for peripherals to enable, I found nothing. I have tried installing different versions of Armbian, but nothing changed: - Armbian_24.5.1_Orangepizero2_jammy_current_6.6.31.img - Armbian_24.2.1_Orangepizero2_bookworm_current_6.6.16.img - Armbian_23.8.3_Orangepizero2_bookworm_current_6.1.53.img - Armbian_24.5.1_Orangepizero2_noble_current_6.6.31.i…

• 1

  Reputation Points

• 3 replies
• 5.9k views
• 1 follower

ALIGMSTEN

June 10, 20242 yr

I just download the image for Oranegpi Zero2 : Armbian 21.08 Bullseye Kernel 4.9.y, Size: 337Mb, Updated: Jan 24, 2022 And I use "usbimage" write the image to my SD card . And, nothing happen, Red LED and Green LED not lighting. Serial Port has no any message. I have 3 SD card, 2 Orangepi Zero2. All of it I test still failure. I have a older image for Orangepi Zero2 name "Armbian_21.08.1_Orangepizero2_buster_legacy_4.9.280.img.xz". This one is useful. BUT, can not "apt upgrade". If you do so , you cannot boot up next time. So I just confuse now......

• 0

  Reputation Points

• 3 replies
• 4.7k views

TheOWL

March 12, 20224 yr

Hello everybody, since an Softwareupdate some time ago, i m not able to boot up the Pine64 with any Image. It doesnt matter what distro, or what channel. Does anybody have the same issue?

• 0

  Reputation Points

• 3 replies
• 2.9k views

martinayotte

August 8, 20188 yr

I got my 320x240 ILI9341 touchscreen to work with the image from the OrangePI site: Armbian_23.5.2_Orangepizero2_bookworm_legacy_4.9.318_minimal The display is one I bought from Amazon Hosyond 2.8 Inches TFT LCD Touch Screen Shield Display Module 320x240 SPI Serial ILI9341 with Touch Pen Compatible with Arduino R3/Mega2560 Development Board This document was very helpful getting the display set up on the OPZero 2: https://tienda.tettsa.gt/wp-content/uploads/2022/08/OrangePi_Zero2_H616_User-manual_v3.7.pdf I still don't have the touch part working. If anyone has success getting 2 selects working with SPI1 on OPZero2 and touc…

• 0

  Reputation Points

• 3 replies
• 12.5k views

robertoj

July 16, 20242 yr

HI, recently downloaded Armbian Jammy CLI for Orange Pi Zero 2 It boots up but doesn't display anything on HDMI. I have to access it via remote ssh on another computer. Any way to enable the HDMI. I was hoping to run a desktop on it. Reading different forums it's suggested that the default check is too short so HDMI is disabled but I've no idea how to disable this. Will there be a desktop version of Jammy for Orange pi Zero 2 available to download? I'm using Jammy with a desktop on a Orange Pi One and it works fine. Thanks

• 0

  Reputation Points

• 3 replies
• 3.3k views

ALIGMSTEN

November 24, 20223 yr

Hi guys, I am newbie, my monitor iiyama ProLite B2888UHSU is flickering random white lines on black screen. U-boot console was displayed correctly. Same flickering I have seen on stock Armbian Bionic mainline kernel 4.19.y (next). Only Armbian Xenial desktop legacy kernel 3.10.y is working correctly. Can you help me? Maybe I can fix it, too, but I don't know, how and where to start. Thanks

• 0

  Reputation Points

• 2 replies
• 3k views

jadamcak

March 27, 20197 yr

Hello everyone, I would like to ask for help in a few subjects where I am a bit lost. I have an orange pi zero 2 (h616) with a tpm2 module and I need some specific kernel modules to be able to build my application on top of the orange pi zero 2 (h616). What I have done: Compiled the trusted firmware from master and generated bl31.bin Compiled the U-boot bootloader from master and generated the u-boot-sunxi-with-spl.bin Compiled the linux kernel version 5.15 (LTS) with the modules I need (mainly about tpm specific modules) and generated the kernel Image Compiled the modules from this kernel Compiled and generated the device tree binary (.dtb) for t…

• 1

  Reputation Points

• 2 replies
• 4.7k views

Felipe

May 5, 20233 yr

Good day. We have a medical device project. We always wanted to have bananapi m4 zero hardware on our main board, with armbian as an OS seeing as it is up to date and fit for purpose. However, our Hardware supplier has not been able to solve the full hardware stack. We currently are able to boot the orangepi zero 3 image... and as far as I understand the hardware chips are very close to each other. We also have emmc on the board. But not working. We desperately need hardware development help so we can get banana pi m4 zero armbian supported OS working. Any advise please. We have 2GB RAM , allwinner h618, axp313. All the same as orangepi zero 3. Pl…

• 0

  Reputation Points

• 2 replies
• 4.4k views
• 1 follower

SUPA

February 22Feb 22

Latest Ubuntu Jammy CLI version and I get: update-initramfs: Generating /boot/initrd.img-5.15.48-sunxi64 W: Possible missing firmware /lib/firmware/rtl_nic/rtl8156b-2.fw for module r8152 after apt upgrade.

• 0

  Reputation Points

• 2 replies
• 6.2k views
• 1 follower

sgjava

August 7, 20224 yr

I have an Orange Pi Zero 2 set up with Octoprint and a webcam. No keyboard or screen, all access over ssh... if it's running. If it started OK, then no problem, everything works fine. If. Usually powering it up lights up the red LED and... it ends here. I waited even half an hour, red, no boot. Occasionally - one in five-ten attempts to boot - the LED turns green after a couple seconds and the board boots fine. Very rarely the red turns to green after a minute or so, and the board boots up. Unfortunately, having no cable to connect it to a monitor or serial, my diagnostics are quite limited - after booting dmesg looks mostly clean, but maybe in case it's a sem…

• 0

  Reputation Points

• 2 replies
• 4.6k views

Werner

February 1, 20233 yr

I believe the TP-Link AC600 wireless usb adapter uses the Mediatek chipset. Has anybody got this running on a Pine A64?

• 0

  Reputation Points

• 2 replies
• 4.4k views

Andro

August 10, 20179 yr

Hello, I've been using OPiZ2 for about 2 years as Pi-hole in gravity-sync with another one (Orange Pi 3 LTS running Open Media Vault with no problem). Today I found out it was dead, no connection and just a blank screen. It must have happened in the past few days, because I checked it on sunday and it was up and running. I'm almost sure I was using it with Armbian_22.11.0-trunk_Orangepizero2_sid_edge_6.0.6. i have extracted the sd card and checked it on Windows with Diskinternals reader and Minitool Partition Wizard, no problem found. The most recent files and folders have been modified on 2024-07-12, eleven days ago, much prior to my checking, so…

• 0

  Reputation Points

• 2 replies
• 3.2k views
• 1 follower

jan_axhell

July 29, 20242 yr

I have PINE A64 WIFI 802.11BGN/BLUETOOTH 4.0 MODULE I can see wifi card but bt is not working Please help me to make this bt module working $ sudo rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no $

• 0

  Reputation Points

• 2 replies
• 2.4k views

Onira

July 17, 20251 yr

Hi guys, I downloaded Armbian 24.2.1 Jammy CLI (Armbian_24.2.1_Orangepizeroplus_jammy_current_6.6.16.img.xz) for the Orange Pi Zero Plus and it's not booting. Boot log below: U-Boot SPL 2024.01-armbian (Feb 09 2024 - 19:21:37 +0000) DRAM: 512 MiB Trying to boot from MMC1 NOTICE: BL31: v2.9(debug):armbian NOTICE: BL31: Built : 19:20:27, Feb 9 2024 NOTICE: BL31: Detected Allwinner H5 SoC (1718) NOTICE: BL31: Found U-Boot DTB at 0x20a4ef0, model: Xunlong Orange Pi Zero Plus INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller NOTICE: PMIC: Assuming H5 reference regulator design INFO: BL31: Platform setup done INFO: BL31:…

• 0

  Reputation Points

• 2 replies
• 3.8k views
• 1 follower

cvxx

April 26, 20242 yr

Hello. BTT says what BTT Pi and CB1 is same, but realy not. Dunno why i brought what board. But now I owner of this "piece of ****" So. New board, clean install v25.11.2 for BigTreeTech CB1 running Armbian Linux 6.12.58-current-sunxi64 Packages: Debian stable (trixie) armbianEnv: overlays=gpu tft35_spi extraargs=fbcon=rotate:2 fbcon=rotate:2 for screen rotation, because armbian not from btt and didn`t have feature like param_tft35_spi_rotate Next, help me to determine how to enable UARTs and I2C From BIGTREETECH_Pi_V1.2.1 Hardware Pdf UART0: CPUX-UTX CPUX-RX UART2 (May work as i2c0; uart2-pi-pins;…

• 0

  Reputation Points

• 2 replies
• 2.6k views
• 1 follower

ComProf

March 13Mar 13

Hello, I have Pine64 2GB I want to connect the temperature sensor DS18B20. How to connect it. Sorry for my English

• 0

  Reputation Points

• 2 replies
• 3k views

chwe

May 5, 20197 yr

Hi everyone. Tried stable and experimental builds. Also build my own image. All 6.x kernels don't seem to have a working wifi on this board. Tried modprobe brcmfmac without any luck - module loads but no wlan0 comes up. The board to my understanding has CYW43455 chip (from Cypress). Apparently there are several variations of BPI M4 Zero. The only image that has working wifi is from BPI website but it's a backports build with 5.4 kernel, so fairly old and outdated (running an upgrade makes the board unbootable). Any ideas? Thanks in advance.

• 0

  Reputation Points

• 2 replies
• 4.1k views

Nikolai Danylchyk

October 16, 20241 yr

I have one on a shelf and want to use it for h265->h264 transcoding. http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-One-Plus.html says it can. H6 Quad-core 64-bit ARM Cortex™-A53 Decoding: H265/HEVC Main/Main10 profile@Level5.2 High-tier ;4K@60fps, up to 6Kx4K@30fps Encoding: H.264 BP/MP/HP encoder up to 4K@25fps or 1080p@60fps Googling finds some old branches of ffmpeg and kernel for H3. Current armbian 25.2.3 comes with 6.12.20-current-sunxi64 which has: sunxi_cedrus v4l2_mem2mem videobuf2_dma_contig videobuf2_v4l2 videodev videobuf2_common …

• 0

  Reputation Points

• 2 replies
• 2.3k views
• 1 follower

aik

May 20, 20251 yr

Dear friends! I have a project, where I needed to use 4 infrared receivers and 2 transmitters connected to GPIO. After a lot of research I realized how to cook all stuffs together: So I have Pine64 A64 512MB cards (not the plus model), running Armbian 20.05.0-trunk.038 nightly, (uname -r: 5.4.18-sunxi64). I needed to freeze upgrades for two reasons: Boot hangs up: The armbian thinks that I have the plus model: on every upgrade I need to replace the "sun50i-a64-pine64-plus.dtb" file with "sun50i-a64-pine64.dtb" at /boot/dtb/allwinner because the non-plus model (512MB) has different ethernet hardware. Missing gpio-ir-recv kernel module from stock A…

• 0

  Reputation Points

• 2 replies
• 5.5k views
• 1 follower

vr1152

August 12, 20215 yr

Mainline stable Armbian stable for Pine64 worked great. I have successfully make my 3.5 TFT screen work but not the touch screen. I read some tutorials, mostly guide. This guide for TFT and Touch is really detailed. For touch: - Step 1: ads7846 driver seems ok - Step 2: ads7846_device there is a warning after make and make install, and it said to skip depmod - After this, I tried sudo modprob ads7846 sudo modprob ads7846_device model=7846 cs=1 gpio_pendown=1 keep_vref_on=1 swap_xy=1 pressure_max=255 x_plate_ohms=60 x_min=200 x_max=3900 y_min=200 y_max=3900 ads7846 is ok (confirmed with lsmod). But ads7846_device return invalid argum…

• 0

  Reputation Points

• 2 replies
• 3.6k views
• 2 followers

shaddow501

June 2, 20197 yr

I'm using a Pine 64 LTS. For this I have downloaded the SoPine images Armbian_21.08.1_Pine64so_buster_current_5.10.60.img and Armbian_21.08.1_Pine64so_focal_current_5.10.60.img Both images boot normally (including network connection), but after the update (apt update, apt upgrade) no IP4 network connection is established for eth0. For help I am very grateful for any help.

• 0

  Reputation Points

• 2 replies
• 2.7k views

Pander

August 28, 20224 yr

Hi, After many attempt to installs and remove various version of teamviewer, I finally was able to make it run successfully. I try to use many architecture package even if they were not supposed to work. The running teamviewer is at the following link. I know it's not supposed to work but it is. https://download.teamviewer.com/download/linux/teamviewer-host_armhf.deb Here kind of command that I used randomly (I know, not really scientific approach!) sudo dpkg --add-architecture amd64 sudo dpkg --add-architecture i386 sudo apt-get install -f sudo apt-get update sudo dpkg --remove-architecture amd64 …

• 0

  Reputation Points

• 2 replies
• 3.9k views
• 1 follower

Guest

October 15, 20178 yr

Hi I have been trying to allocate specific gpio's as input via the Device Tree, this ultimately being for a custom made board. I can and have successfully allocated pins PB0, PB1, PB3 & PB5, which are showing in /dev/inputs/by-path and have been verified working with evtest. Working code :- /dts-v1/; /plugin/; / { fragment@0 { target = <&pio>; __overlay__ { input_0: input_0 { pins = "PB0"; function = "gpio_in"; bias-pull-up; }; }; }; fragment@1 { target-path = "/"; __overlay__ { button_1 { compatible = "gpio-keys"; pinctrl-names = "default"…

• 0

  Reputation Points

• 2 replies
• 3.8k views
• 1 follower

Gavinb

May 24, 20188 yr

Hi, I'm trying to use the emmc device located on the Pine64LTS - not neccessarily to boot (though that would be nice). I'm employing a 16GB FORESEE card, which I obtained from the Pine folks. First I installed the Stable SoPine64 Armbian_5.30_Pine64so_Ubuntu_xenial_default_3.10.105 image from the Download web page. When I booted the image from an microSD card, only /dev/mmcblk0 showed up - no /dev/mmcblk1. When I tried to boot from the image loaded on the emmc card, the boot failed. Next I tried to build a more up-to-date image, using: git clone --depth 1 https://github.com/armbian/build cd build ./compile.sh And using the ch…

• 0

  Reputation Points

• 2 replies
• 3.9k views
• 1 follower

linda

September 11, 20188 yr

I am currently using the Armbian 20.02 release and doing some tests with the serial ports of a Pine64-LTS board. I noticed that i could not get all the serial ports to work. I needed to make a couple of changes in order to get them all working. Maybe i did something wrong and my changes were not needed, but i still would like to list them here in order to help other users who are having problems with the serial ports. When first starting up the armbian release i used the armbian-config tool to enable the uart 1, uart 2, uart 3 and uart4. I rebooted but noticed not all ports where present. I noticed a message in the dmesg log showi…

• 0

  Reputation Points

• 2 replies
• 4k views

Patrick Peters

February 25, 20206 yr