Rockchip

I don't know where else to share this so I'm putting this here. The board recognizes and tries to the load the driver for an AR9462 QCNA222 M.2 WiFi card, but fails. I tried a custom build found on Radxa forum/github, built Armbian myself, and tried an official build. All resulted in the same error. Card was tested and working correctly on 2 different Debian x86 machines. lspci 0000:00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01) 0000:01:00.0 Network controller: Qualcomm Atheros AR9462 Wireless Network Adapter (rev 01) 0002:20:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01) dmesg ath…

I had tried twice making OPi3b img but it always gave me kernel panic. The reason is my SBC v2.1 while all sources / firmware used in build framework corresponds to v1.1. I have given a week to study .dts .csc & defconfig files which are all different from latest SBC v2.1 v2.1 using Broadcom AP6256 & examining official builds by vendor it uses wl driver In order to get wireless working as well as solving kernel panic error I tried doing this Step 1 Changed .csc file in /home/ukhan/build/config/boards. From default to new (hastebin links) Default csc file was weird this file didn't exist BOOTCONFIG="orangepi-3b-rk3566_de…

Hello, I am selling a working unit of Kobol Helios64 with the fix done, without drives. Based in Czech Republic, able to send within EU. Please DM me if interested.

Hello I recently set up NextCloudPlus/NextCloudPi on a Rock64. I used the image that can be downloaded from the ownyourbits website, cat /etc/*-release resulted in the following output: BOARD=rock64 BOARD_NAME="ROCK64" BOARDFAMILY=rk3328 VERSION=5.44 LINUXFAMILY=rk3328 BRANCH=default ARCH=arm64 IMAGE_TYPE=user-built BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image 03af3b07-6131-4b1c-8cc2-7f716caf75e1 # PLEASE DO NOT EDIT THIS FILE BOARD=rock64 BOARD_NAME="ROCK64" BOARDFAMILY=rk3328 VERSION=5.44 LINUXFAMILY=rk3328 BRANCH=default ARCH=arm64 IMAGE_TYPE=user-built BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image PRETTY_NAME="Debian GNU/Linux 9 (stretch…

I tried building the mainline kernel (ayufan) for NanoPC T4. My aim is to bring up bluetooth. No quite familiar with device tree, just googling and reading the kernel doc, and now I had some luck. According to this post (https://discuss.96boards.org/t/updated-preliminary-support-for-bluetooth-in-debian-rock960/5588/7) in 96boards forum, in recent kernel, there is a serial bus support for bcm blutooth. ---- firmware. I used firmware from the repo mentioned in the post: https://github.com/openwetek/wlan-firmware-aml/blob/master/bcm_ampak/config/4356/bcm4356a2.hcd according to hci_bcm.c code, this file should be renamed to BCM4…

Has anybody successfully used the USB type-c displayport of the nanopc-t4? How do you configure it? It works on the images provided by friendlyelec, so, I guess it is just a config/install issue ?

I've got an m4v2 running current armbian (Armbian_19.11.4_Nanopim4_bionic_legacy_4.4.192_desktop.7z) I get a stack of messages on tty1 and in dmesg stating "get wrong frequency". it was also logging via syslog, but I have disabled those from logging. it also seems to generate one of these messages every time I hit a key on the keyboard. somehow related to kbd interrupt? ondemand cpu freq scaling works, running cpu intensive jobs, the following frequencies were observed Jan 11 10:45:01 m4-2 root: CPUTEMP 45.00 (600.00/600.00) Jan 11 21:50:01 m4-2 root: CPUTEMP 44.44 (1416.00/600.00) Jan 11 21:55:01 m4-2 root: CPUTEMP 45.62 (1416.…

Hi, I don't have an idea why it stucks. Armbian_20.05.0-trunk_Rockpi-4b_buster_current_5.4.43 EDIT: I have downloaded the pre-build image Armbian_20.05.1_Rockpi-4b_buster_current_5.4.43 and it works. It boots at an astonishing speed, only 18 sec which is a miracle. How can I build the same kernel? Is sufficient to copy just a .config file? T T DDR Version 1.13 20180801 In Channel 0: LPDDR4,50MHz CS = 0 MR0=0x98 MR4=0x3 MR5=0xFF MR8=0x8 MR12=0x4D MR14=0x4D MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x4D MR14=0x4D MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 Bus Width=32 Col=10 Bank=8 Row=15/15 C…

I can't get my 5B to recognise the Coral USB Accelerator. lsusb doesn't show anything but does when I attach a USB storage device. I've installed libedgetpu1-std with a validated gpg key but nothing happens - the led on the device doesn't even turn on. Do I need to install a special USB driver or something into the kernel ?

Since I am interested in the connection ability, I figured the info we gather should go into ONE thread. I have tried to build new kernels, but can only see USB controllers and devices two ports. I have seen a lot of work by Sebasitian Reichel @ Collabora, and his patches, but these do not seem to have the desired result on my test board. Orange PI 5. There seems to be an issue with the port mux, FUSB302, that either connects the last USB to the "vertical" port or to the "USB C" connector. I will comment my findings and attempts to correct this in this thread, and think we could find out where we are if you add your findings, successes…

I'm getting this weird graphical artifact on a Radxa Rock 4SE connected to a TV via HDMI. It covers roughly a third of the right side of the display, note that the terminal window is covered by the artifact but the cursor is above it. I started from a Debian minimal image and added the desktop environment via armbian-config. The artifact is visible on both GNOME and KDE Plasma (with fully updated system on both rolling and stable) but not with XFCE. It also disappears with resolutions lower than 4K or switching to tty. Any idea what might be causing this?

I have some bose speakers plugged into the A/V and i am getting no sound. does this feature work on the POCK 64? or is audio only through HDMI. my monitor has no audio support.

Hi, I am using Armbian_19.11.3_Rockpi-4b_buster_current_5.3.11_desktop. Facing issue when trying to use USB devices in the upper USB 3 port on a Rock Pi 4 v1.3. This port also supports USB OTG. The switch is set to Host mode. The storage is detected occasionally, while most of the time it does not work. dmesg contains no reference to the connected storage: $ dmesg | grep usb [ 0.000000] Kernel command line: root=UUID=590fca6f-9771-4245-86a7-34712bfe535b rootwait rootfstype=ext4 console=ttyS2,1500000 console=tty1 panic=10 consoleblank=0 loglevel=1 ubootpart=7ef2aff3-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u cgro…

I don't know if it's of any use. Just noticed this issue of reboot not working on Buster legacy. Seems to be hdmi related. When I pull out hdmi for a few seconds then it does start booting. I remember this used to be the same on bionic mainline. Don't know why it's here now. I'm on NanoPi M4V2.

Is anyone having issues with the Cinnamon desktop version restarting the desktop when using the menu app launcher? Can be repeated by launching with super key and typing anything for search or just launching any application. Happens with all 3 major menu app launchers. menu, cinnamenu and cinnstark Pinebook pro

Upgrading Helios64 from Armbian Buster to Bullseye (see below) works as expected on my system. However, I am using systemd-networkd and just a few services (nextcloud, netatalk, etc. and not ZFS) EDIT: Upgrading Buster installations to Bullseye also works fine if you use network-manager, even if you have a bridge configured (using bridge-slave; binutils-bridge). # cat /etc/os-release PRETTY_NAME="Debian GNU/Linux 11 (bullseye)" NAME="Debian GNU/Linux" VERSION_ID="11" VERSION="11 (bullseye)" VERSION_CODENAME=bullseye ID=debian HOME_URL="https://www.debian.org/" SUPPORT_URL="https://www.debian.org/support" BUG_REPORT_URL="https…

Last night I shutdown my Helios 64 (sudo shutdown now) but when i went to boot it this morning, after startup it looks to be hung, all blue lights solidly on. It's set to run from the micro SD card, so wondering if i hit a R/W limit on that. Serial log below, it doesn't progress beyond "starting kernel" I can mount the MicroSD on my ubuntu box and read the file structure DDR Version 1.24 20191016 In channel 0 CS = 0 MR0=0x18 MR4=0x2 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x18 MR4=0x1 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channe…

I've installed Armbian_v22.05.2_Rockpi-4cplus_jammy_current_6.1.33_minimal and whatever I try to play a 1080p video via the performance is horrible with very slow refresh, totally unusable. Normally loki gives me acceptable performance on SBCs of similar performance but not in this case. The Rock 4c plus is quite powerful so I'm really shocked at how badly it's performing. Let me be clear, I understand that the issue I see is not that the Rock 4c plus isn't cable of playing video, clearly it is and I'm not complaining about the hardware of the device. It's just that the software being used clearly needs to be optimised for it and most things out th…

Hi All, in an attempt speed up my Armbian image build process I put the last build choices in a bash script ./compile.sh BOARD=nanopim4v2 BRANCH=current BUILD_DESKTOP=yes BUILD_MINIMAL=no\ DESKTOP_APPGROUPS_SELECTED='browsers editors'\ DESKTOP_ENVIRONMENT=gnome\ DESKTOP_ENVIRONMENT_CONFIG_NAME=config_base\ KERNEL_CONFIGURE=no RELEASE=jammy but I still get prompted for input when I run the script - what am I doing wrong ?

Hi, on orangepi5B, not possible to insert module g_ether root@orangepi5:~# modprobe g_ether modprobe: ERROR: could not insert 'g_ether': Exec format error root@orangepi5:~# uname -a Linux orangepi5 6.1.75-vendor-rk35xx #1 SMP Wed Aug 21 11:45:59 UTC 2024 aarch64 GNU/Linux root@orangepi5:~#

Filed this as armbian/build#10551 and was (reasonably) pointed here instead, since it's a kernel-code observation rather than a build-framework bug. Posting for the record — this is a question about the code, not a bug report. Where: drivers/gpu/drm/rockchip/rockchip_drm_vop2.c — identical across Rockchip BSP 6.1, ubuntu-rockchip, and Armbian rk35xx-vendor-6.1 (carried unpatched). rk3568_vop2_cfg_done() waits for the layer-select latch to take effect when it changes: old_layer_sel_val = vop2_readl(vop2, layer_sel_offset); cfg_layer_sel_val = vop2->regsbak[layer_sel_offset >> 2]; ... vop2_writel(vop2, 0, val); /* Make sure the layer sel is take…

Hi! I have the problem that when I try to boot with any Kernel other than 4.4.x, U-boot gives me the "Bad ARM64 Image Magic" Error and stops booting. I can build my own 4.4 Kernels without any problem, those will boot fine. But If I try any newer kernel, for example a NEXT Kernel (package linux-image-next-rockchip), or a DEV Kernel (package linux-image-dev-rockchip), or even if I compile my own 5.3 Kernel, a boot attempt always results in the Bad Magic error. I also have this problem when I install a whole 5.3 Armbian Image (for example https://dl.armbian.com/rockpro64/Buster_current_desktop) I have three RK3399-…

Hello, I think this is my first post here. I am trying to operate an Epson L4150 on-board Rock pi4 b multifunction printer. I was successful in running the printer. But the scanner is another story. Xsane does not recognize it. I have been trying to install the driver which is downloaded from the Epson page, but it is for armhf. I tried a dpkg --add-architecture armhf, then update, but when I try to run install.sh from the Epson driver, it throws error: E: Failed to locate package libboost-filesystem1.58.0 Somebody could help me? Thank you

Hello, When I comment device via USB 3.0 I see it: ender3@ender3:~$ lsusb Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 004 Device 002: ID 1d50:614e OpenMoko, Inc. Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub However with pins GND, DP1, DM1, +5V Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID …

Hello everyone, i was thinking about running a jellyfin server on the Rock64, is there any chance for hardware encoding? Thank you in advance Regards

Hello! First off, thanks for the amazing product you all have created - huge props to everyone who contributes! I have been trying to get Armbian completely working on my Orange Pi 5b for a week now. Most notably: WiFi. Just a few moments ago I set up a new build of Armbian again, on an empty SD card. The one from https://www.armbian.com/orangepi-5/, Armbian 23.5 Jammy Gnome, as the more recent builds' armbian-config don't seem to have an option to enable overlays. After doing the default setup (user, locale, and it asks for "connect via wifi?" but shows no WiFi devices), I ran armbian-config. I go to System -> Hardware, b…

Seems like a great little box, but Radxa doesn't have much info about the hardware side of it. Simple stuff like accessing the LEDs and buttons when running Armbian. Posted on the Radxa website but no replies, so just curious if anyone has dug into it at all?

Orange Pi 5 pro,whith Armbian_community_26.2.0-trunk.7_Orangepi5pro_noble_vendor_6.1.115_gnome_desktop 。 when I try to start Eclipse/idea/vscode or other JavaApp , java processes crash and gets core dump every time, tested on Jdk 17,21 25 ,both openjdk and oracleJDK。 It seems there is a compatibility issue between the kernel and the JDK. How can I fix it? Or I have to wait kenel update? some error like Current thread (0x0000ffffa802b9b0): JavaThread "main" [_thread_in_vm, id=6202, stack(0x0000ffffaeb62000,0x0000ffffaed60000) (2040K)] Stack: [0x0000ffffaeb62000,0x0000ffffaed60000], sp=0x0000ffffaed5ce40, …

Hi, everyone. The Kobo site is kind of difficult to navigate if you're looking for relevant information, but I came to the conclusion that this is the right place for support. Forgive me if I'm mistaken. I was wondering if someone could help me interpret these bootlogs from serial term when trying to boot my Helios64 from the EMMC. Following the instructions on Kobol's site, I flashed their u-boot image to an sd card, booted the Helios64 off of said sd, fetched the latest image of Armbian, unpacked that image, and flashed it from my laptop to the Helios64 via usbc to what I presume is the correct interface. Could it be that I messed up? Here's a quick example …

I'm owner of a rock 5b with an nvme drive installed. I'm already running Armbian_23.02.2_Rock-5b_bullseye_legacy_5.10.110 from the nvme. I want try the edge images but I cannot boot them from the SD. I have tried with Armbian_23.05.0-trunk-e33842ef2_Rock-5b_lunar_edge_6.2.9 and Armbian_23.05.0-trunk-e33842ef2_Rock-5b_lunar_legacy_5.10.110 Am I missing something?

I just bought one NanoPi M4 on FriendlyArm Black friday, I was wondering if the Raspberry Pi Oficial 7" display works with the DSI connect on NanoPi M4?

Have anyone tried to use USB connected monitor with NanoPi? I'm thinking about buying one but not sure it can work with it or, if some change has to be done to NanoPi , I would like to know about it.

I have a Rock64 v2. For my project I wish to connect the board to an MCP3008 ADC chip via SPI so I can read some analog sensors. Pretty straightforward. But when I look at /lib/modules/4.4.178-rockchip64/kernel/drivers I see there are modules for i2c, usb, one wire, GPIO ... everything but SPI. Am I out of luck? ARMBIAN 5.75 stable Ubuntu 18.04.2 LTS 4.4.178-rockchip64

Hello, ttyS2 is used for console output by default. In my application I need this port for custom communication. Is there any way to disable the console on it? Thanks

Hi, I am testing mesa panfrost on RK3399 and I am facing an odd problem. When joint the chroot as root I get mesa working but if I join as pi, the user, I cant get it working and I've receive just a soft render (llvmpipe) How this could be fixed?? any experience??

I have recently started working with a NanoPi R2S. I have it booting from the built-in microSD. However, I would like to be able to boot off of USB. When I interrupt u-boot and start USB on the board, it finds the hub but does not seem to find *any* device. I have tried various USB sticks of different sizes and brands, and a few ordinary devices such as a mouse. Nothing. Is this a known problem? Should it be able to work? Thanks

After dist-upgrade, I got seg fault when using wget. Spoiler root@nanopi-r2s:~/lepup# cat /etc/debian_version 10.6 root@nanopi-r2s:~/# uname -a Linux nanopi-r2s 5.9.11-rockchip64 #20.11.1 SMP PREEMPT Fri Nov 27 21:59:08 CET 2020 aarch64 GNU/Linux root@nanopi-r2s:~/# apt-get install wget Reading package lists... Done Building dependency tree Reading state information... Done wget is already the newest version (1.20.1-1.1). 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. root@nanopi-r2s:~/# strace -o /tmp/wget.tr wget Segmentation fault root@nanopi-r2s:~/# cat /tmp/wget.tr execve("/usr/bin/wget", ["wget"], 0xffffcfbd4160 /* 23 vars */)…

Hi, I am trying to disable UAS mode on attached USB HDs (I have quite a good amount of those) to avoid quite common issues. However, it seems that the usb_storage.quirks string is limited to 127 chars! dmesg shows: usb_storage.quirks: string doesn't fit in 127 chars I do not really see the point of limiting the string length to 127 chars..a bit more would be appreciated. Thanks

Hi, any hope to have a 5.x server image with support for the M1 bluetooth soon ? Chris

I simply can not figure out why UART4 at GPIO1 header with the pins 19 (TX) and 21 (RX) not working at all. I see that here (ttyS2) is running an agetty but there is no serial activity at any baudrate (9600, 115200). Please help me.

) my Setup is : **Board**: Helios64 (RK3399) - **Kernel**: `6.18.44-current-rockchip64` - **Armbian**: 26.8.3 (upgraded from 25.11.2 via apt) - **Boot**: currently booting from SD card (rootfs on mmcblk0); b) symptoms : After upgrading to 26.8.3, my drives are no longer detected — but only on a "warm reboot": - ASM1061 PCIe-SATA controller (bays 1-2) completely missing from `lspci` - JMS561 USB-SATA bridges (bays 3-5) missing from `lsusb` - Other USB devices (VIA hubs, Realtek USB NIC) enumerate fine - No `sdX` block devices at all in `lsblk` The only fix is a "cold boot": `poweroff`, unplug the power cable, wait 1-2 minutes, power back …

I am running last stable armbian with kernel 4.4.192-rockchip64 on emmc - really everything works nice (only thunderbird is very slow) - thx a lot for your work. The only thing I could not figure out, how I can wake up from suspend by keyboard or mouse. The armbian image uses org.freedesktop.login1.suspend to suspend - normally I am used to upower or pm-utils and there it was until now all the time possible to wake up with keyboard. Its quite uncomfortable to wake up the Rock64 with the power button - hidden, very small hole, I just use now a wooden chopstick for wakeup. Does anybody know, how to configure wakeup-hooks / wakeup-events for systemd …

Hello, is it possible to install WiringPi on Rock Pi 4? I tried to install WiringX using the instructions on https://github.com/wiringX/wiringX , but after installing it the command "gpio" is not present. Any hint on how to get "gpio" command on Rock Pi 4? Thanks

For a few Weeks i have little problem with my Nano Pi M4. Whenever I boot up it says: "Loading, please wait...starting version 237" and then i have to wait . Finally it boots up, but there were times this SBC was booting really fast. Is there something i could do, to speed up booting again? Regards

Hello together, i experienced network problems with Helios64 and latest Debian Buster Image. I cannot setup a static ip address after installation of OMV5, moreover it crashes on install. I double checked it on a fresh image without any changes and an immediate installation of OMV over softy. The result is the same. After the crash OMV is in fact available, but the network configuration is broken and a static setup doesnt work over the OMV UI, nor armbian-config, also the boot takes about 2-5 minutes due to whatever reason. armbianmonitor http://ix.io/2PPJ

Hi folks, I am wondering if somebody with a mac enviroment has a decent / performant samba connectivity? After I upgraded to Big Sur I have severe issues with the samba protocol when accessing my shares on the helios running openmediavault. I know that Apple had made some changes with samba but there might be some users that dug a little bit deeper and could give me a hint. I did try it with different settings in the extra options over the past weeks but with no luck so far. Sidenote: Also NFS is terribly slow and laggy. I am back with AFP connection now that does the job perfectly and fast.

Hi Is it possible to install the system on NMVE M2 ? Or how to completely transfer the SD card OS to NMVEIs it possible to install the system on NMVE M2 ?

Hi, I've installed minimal cli version and it restarts when connected to PC via on-board USB-C connector. Board hangs after: [ OK ] Reached target Hardware activated USB gadget. Host computer does: [ 4881.959467] usb 1-5: new high-speed USB device number 47 using xhci_hcd [ 4882.140301] usb 1-5: New USB device found, idVendor=0525, idProduct=a4a6, bcdDevice= 5.15 [ 4882.140315] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4882.140322] usb 1-5: Product: Gadget Serial v2.4 [ 4882.140327] usb 1-5: Manufacturer: Linux 5.15.80-rockchip64 with ff580000.usb [ 4883.572730] usb 1-5: USB disconnect, device number 47 [ 4884.079492] usb 1-5: …

Hi I have install the armbian system into my SSD device. But how can i manage to get it to start from that? The system dont seems to want to boot only from that SSD. I need to have the Micro SD inserted into the card reader for it to be able to boot. After that it seems to first boot up whit the SD card after that switch over to the SSD. How is that happening? NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 465.8G 0 disk └─sda1 8:1 0 461.1G 0 part /var/log.hdd / mmcblk0 179:0 0 29.8G 0 disk └─mmcblk0p1 179:1 0 29.5G 0 part zram0 2…

Hello all, since I didn't find a hint in an other blog I opened this topic. I tried to install gdm3 on a Armbian_23.5.4_Rock-5a_jammy_legacy_5.10.160_gnome or xcfe installtion in order to enable Wayland. I always got the masseage: Does anybody have an idea? Thanks, Best regards, Kersten

I have an Orangepi5 ultra RK5388. I have tried the following versions of Armbian13. It doesn't recognize my USBs so I don't have a keyboard. vendor: https://armbian.systemonachip.net/dl/orangepi5-plus/archive/Armbian_25.8.1_Orangepi5-plus_trixie_vendor_6.1.115_minimal.img.xz.sha This one won't start ,current: https://armbian.systemonachip.net/dl/orangepi5-plus/archive/Armbian_25.8.1_Orangepi5-plus_trixie_current_6.12.43_minimal.img.xz There is also no reference to Debian13 in any repository on the Orangepi website.

Hi Folks, I have a NanoPiM4 and loaded Ambian 5.75 onto an SD card, it boots great (Thanks Armbian!). How I've added the FriendlyElec 2.8 TFT module (240x320) and want to configure it. So I used the handy `armbian-config` to pick up the kernel headers and sources, and went to go an add fbtft and select the ST7789V driver. Only when I went to run `make menuconfig` I got: root@nanopim4:/usr/src/linux-source-4.4.174-rk3399# make menuconfig scripts/kconfig/mconf Kconfig net/Kconfig:83: can't open file "net/wireguard/Kconfig" scripts/kconfig/Makefile:28: recipe for target 'menuconfig' failed I've updated the armbian monitor stuf…

Hello, I have a Helio64 not yet configured and I would like to be able to install the latest image available on https://armbian.hosthatch.com/dl/helios64/archive/ and especially to install the latest OpenMediaVault 6 version. Do you think this is possible ? Or will OpenMediaVault 6 not be available from armbian-config? As I write this post, the latest image available for Helios64 is Armbian_21.05.9_Helios64_bullseye_current_5.10.63.img.xz I thank you for your help Flolm

Hi there ... Not sure if anyone has an idea here, but I have the following topic: I have a helios64, equipped with 3 2.5" disk drives, running Debian 10 with Kernel 5.10.43. Usually the system runs stable ... even for days (24/7). But every now and then the disks "fail" - which means, during normal operation suddenly the disk turn of, linux reports "sata link down" ... and the disks are off. As if they were removed. If I reboot I usually here only some "klicks" ... I assume the disks try to spin up, but fail due to not enough power (?). To recover from that situation, I usually disconnect power (incl. the internal UPS) ... try a few times, and …

Hello, I apologize for my bad English. I have a NanoPi R6S and a NanoPC T6. Both Nano devices have Armbian images. Both devices use a processor: CPU Model: Rockchip RK3588 Number of Cores: Quad-core ARM Cortex-A76 + Quad Core Cortex-A55 Frequency: Cortex-A76 (up to 2.4GHz), Cortex-A55 (up to 1.8GHz) A few things struck me On NanoPi R6S in the dts file, the frequency of A76 cores is up to 2.4GHz you can see the frequencies at which each core works cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_available_frequencies 408000 600000 816000 1008000 1200000 1416000 1608000 1800000 408000 600000 816000 1008000 1200000 1416000 1608000 1800000…

Despite this being the supported image advertised for the board, it just does not boot on this board, whereas the "current" image does boot (but with limited hardware support). I'm booting with just the serial console connected, to limit interferences On serial console with default config I get: Found U-Boot script /boot/boot.scr 3185 bytes read in 4 ms (777.3 KiB/s) ## Executing script at 00500000 Boot script loaded from mmc 1 117 bytes read in 3 ms (38.1 KiB/s) 7861795 bytes read in 361 ms (20.8 MiB/s) 20770824 bytes read in 941 ms (21.1 MiB/s) 104363 bytes read in 11 ms (9 MiB/s) 2698 bytes read in 7 ms (376 KiB/s) Applying kernel provided DT fixup…

Hi I found the following page https://www.armbian.com/rockpi4/ but I guess those files are for rock pi 4 and not rock pi 4 c? It has a link to 4 c plus images https://fi.mirror.armbian.de/dl/rockpi-4cplus/archive/ but they only contain bullseye? So are there any plans for rockpi 4 c plus to have a bookworm image? Are there any github pipelines that build them where I could send a pull request? (not that my c or c++ compilation skills are existing but I would be happy to give it a try).

Hello all, I am trying to host the rtsp server using gstreamer on armbian. everything is latest and updated. I found, bare rtsp server is taking 3-4% of cpu usage. when I add timestamp and text overlay, cpu goes 23-25%. I was checking if I can enable GPU support, here is output. My system is on NVME, and its working so not sure why error popped. I am connected to wifi, so again not sure why wifi drivers are having issues. however my board never shows it has gpu. can some one guide me ? I have 2 mp camera, not a huge load. again memory is 8GB but never used beyond 1GB, but CPU is most of the time on above 70% dmesg | grep -i error …

HI I just bought 2 neo3 and started with Armbian and the MAC address is the same. But using the official image is a different MAC address.How can I use Armbian so that neo3 has the correct unique MAC address? I use cmd xxd / sys / bus / nvmem / devices / rockchip-efuse0 / nvmem I get the same value.

I built a version of Buster with the legacy kernel (4.4). when I try to install the media-buster-legacy-rk3328 package on the system, I get an error - unsatisfied dependencies on the kodi-rk package. I tried installing the Kodi-rk package manually, but it has an unsatisfied dependency on kodi-rk-bin. The kodi-rk-bin package is available and installed, but its version does not correspond to the links with Kodi-rk. Perhaps packages were updated in the repository, but dependencies do not work because of a complex package name (the alphabetical comparison condition is not met) ?

Setup: Helios64 with Armbian 20.08.8 Buster with Linux 4.4.213-rk3399. Will change to Linux 5.8 soon though. 5 x 8 TB drives. Not using battery. I’ve had this issue ever since beginning to use my Helios. It first happened when I tried building a RAID with OpenMediaVault: It would crash and reboot while building. Sometimes after only 10 minutes, sometimes after 8+ hours of working. The same is true for video transcoding nowadays: it will sometimes crash after a little while, sometimes after a few consecutive hours of working, but it will never be able to work much longer than 12 hours on such a task. Copying large files from the internet has a similar risk of c…

Hi there, Just got OPi4 after some problem from Chineses... Problem: - no at all output at HDMI (connected to HDMI-VGA converter and 1920x1024 VGA LCD display, works with OPi PC+), - if Eth connected device gots (after few minutes) IP from DHCP. - no server running on that IP (tried telnet, ssg, WWW), PING works. uSD card with Armbian Buster for OPi4. What to check next? Console? What speed? 115200 or 1.500.000?

I have a 5B and it came in a kit with the 10.1" touchscreen because I wanted to try to do a kiosk. I used Armbian Lunar rolling to get the OS installed on the emmc but I haven't been able to get the touchscreen working. It uses a breakout board to split the LCD2 connector into two connections on the display (I'm assuming one is touch and one is display) and when it's all plugged together, nothing happens. I've tried enabling and disabling both orangepi5lcd dtds and it doesn't help. When I do a dmesg (regardless of the screen being attached) I have Goodix i2c error for touchscreen@14 I've been doing Rockchip SBCs …

Happy new year everyone, So I really do not like the stub-resolver in Debian/Armbian , and I do not like forwarding any DNS request to any 3rd party in general. After some searching I found this: https://www.turek.dev/posts/disable-systemd-resolved-cleanly/ . Since we are on Armbian we need also remove the 00-armbian-default-dns.conf which points to cloudflare's 1.0.0.1 . 1. We probably do not need this, but just in case someone does not have it. sudo mkdir -p /etc/systemd/resolved.conf.d/ 2. We set the DNS Stub Listener to no and remove the comment from the line if applicable: sudo sed -i '/DNSStubListener=/s/^#//;s/=.*/=no/' /etc/…

On an OrangePi-5b, `apt-get update` a few days ago updated the kernel, and now bluetooth no longer works. What's the proper way to downgrade the kernel to whatever I had before? (armbian-config shows way too many options)? Better yet, get it working again? bluetoothctl does not see the controller at all, and dmesg gives the following: $ dmesg|grep -i bluetoo [ 2.796188] Bluetooth: Core ver 2.22 [ 2.796203] NET: Registered PF_BLUETOOTH protocol family [ 2.796206] Bluetooth: HCI device and connection manager initialized [ 2.796211] Bluetooth: HCI socket layer initialized [ 2.796214] Bluetooth: L2CAP socket layer initialized [ 2.796220] Blue…

I want to share a solution to a problem that I had: Problem: The problem was that no HDDs nor JMB585 were being detected. If I run the `lspci -nn`, it would show no devices: # lspci -nn And there were some `PCIe link training gen1 timeout` in the kernel messages. root@helios64:/home/amreo# dmesg | grep -Ei 'sata|ahci|scsi|ata|sas|sd[a-z]|helios' [ 0.000000] Machine model: Kobol Helios64 [ 0.000000] NODE_DATA(0) allocated [mem 0xf77c6800-0xf77c8fbf] [ 0.000000] printk: log buffer data + meta data: 262144 + 917504 = 1179648 bytes [ 0.016416] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.022065] Memory: 3778312K/4061184…

I've got bluetooth working flawlessly. OpenGL works fine, Plex Media Server works , SONICC, RADARR all performed well, I built the latest and greatest Plex Media Player. A attempted to get VDPAU acceleration working. I'm running the nightly build with the nanopc-t4 overlay. Just about everything works. video playback works with GL accelleration but VDPAU is needed for mkv files. I installed the vdpau mesa support, and tried the libvdpau-sunxi1 driver. Is there anyone else working on something similar ? vdpauinfo display: :0.0 screen: 0 Error creating VDPAU device: 25

https://www.cnx-software.com/2019/11/19/orange-pi-4-4b-sbc-rockchip-rk3399-soc-gyrfalcon-2801s-npu/

Focal / root on eMMC / ZFS on hdd / LXD / Docker I received my Helios64 yesterday, installed the system, and decided to write down my steps before I forget them. Maybe someone will be interested. :-) Preparation: Assembly your box as described here. Download Armbian Focal image from here and flash it to SD card. You may use Ether. Insert the SD card to your Helios64 and boot. After 15-20s the box should be accessible via ssh. (Of course you have to find out it's IP address somehow. For example check your router logs or use this.) First login: ssh root@IP Password: 1234 After prompt - change passw…

I originally installed Armbian witk Kernel 4.4 on my Nanopi.m4 and later upgraded it to 5.10 via armbian-config. Things work fine but whenever I got a new update via apt update, things get messed up a bit the /boot/Image got linked to vmlinux-4.4.213-rk3399 instead of vmlinuz-5.10.35-rockchip64 while others uInitrd -> uInitrd-5.10.35-rockchip64 dtb -> dtb-5.10.35-rockchip64 The result's the board couldn't boot-up, when I restarted it. And, I need to correct the Image -> vmlinuz-5.10.35-rockchip64 and doing mkimage -C none -A arm -T script -d boot.cmd boot.scr from another linux machine to the SDCard. It works fine …

Hey there, I just joined the ARM universe & to be honest I lost all my skills with Linux. First I tried some official images Armbian_22.11.1_Rockpi-4cplus_jammy_current_5.15.80_xfce_desktop.img & with all of them I got a Blackscreen after the Logo. (all settings were made) Then I a tried a pre-release so I could finally get into armbian. Wifi : I couldn't connect via. wifi, "wifi network could not be found" But it was listed with a good signal strength. BT: no adapter was found. ( I used armconfig to enable BT) USB: just 3 of 4 usb ports were working. ( I guess it was 1x usb 3.0 & 2x usb 2.0) The Rock P…

Brand new out of box, the wireless works fine on the orange android os. I then downloaded the orange os aarch64 image and installed. It was the latest. Wireless did not work, but after a couple lines of code/commands it did. I had to add a line to the orangepienv.txt file that was dealing with overlays. After that and a reboot it worked fine. BUT it is seriously boxed in. That is, because of lack of aarch64 support I could not download what I needed...so I tried debian which worked ok, but had issues with processing streaming video over 480p...anything higher I was having screen stutter and ripping plus their was artifacts everywhere. Finally I settled on Armbian,…

Hello everyone, Hello everyone, I have installed Armbian Bookworm 23.11.1 (kernel 5.10.110). The fan control does not work. The fan only runs at level 1. None of the many patches I tried worked. The last one tried was this: https://forum.radxa.com/t/guide-on-how-to-customize-you-pwm-fan-curve/17442 I can adjust the fan manually, but the automatic doesn't work. The "policy" file (/sys/class/thermal/thermal_zone0/policy) cannot be permanently changed to "step wise" (logged in as root). After restarting it is back to "user_space"... The access rights are: -rw-r--r--1 root root 4096 Feb 11 02:42 policy …

Armbian 24.5 works normally, but this issue occurs in versions 24.8, 25.5 and 25.8 [ 0.872698] dwhdmi-rockchip ff940000.hdmi: supply avdd-0v9 not found, using dummy regulator [ 0.872852] dwhdmi-rockchip ff940000.hdmi: supply avdd-1v8 not found, using dummy regulator [ 2.361552] dwhdmi-rockchip ff940000.hdmi: supply avdd-0v9 not found, using dummy regulator [ 2.361723] dwhdmi-rockchip ff940000.hdmi: supply avdd-1v8 not found, using dummy regulator [ 2.361912] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY) [ 2.363007] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffff80008120fe60) …

I am trying to extend the chipselect from spi4. Because I will need to control more boards, so I tried to transform GPIO into chipselect (CS). This is the original SPI4: /dts-v1/; / { fragment@0 { target = <0xffffffff>; __overlay__ { status = "okay"; #address-cells = <0x01>; #size-cells = <0x00>; pinctrl-names = "default"; pinctrl-0 = <0xffffffff 0xffffffff 0xffffffff>; spidev@0 { compatible = "rockchip,spidev"; …

Dear all, i have been using Armbian bionic currently running kernel 4.4.156-rockchip64, for sharing files over the internet, i am currently using sshfs. Openssl benchmark ls as followed OpenSSL 1.1.0g 2 Nov 2017 built on: reproducible build, date unspecified options:bn(64,64) rc4(char) des(int) aes(partial) blowfish(ptr) compiler: gcc -DDSO_DLFCN -DHAVE_DLFCN_H -DNDEBUG -DOPENSSL_THREADS -DOPENSSL_NO_STATIC_ENGINE -DOPENSSL_PIC -DOPENSSL_BN_ASM_MONT -DSHA1_ASM -DSHA256_ASM -DSHA512_ASM -DVPAES_ASM -DECP_NISTZ256_ASM -DPOLY1305_ASM -DOPENSSLDIR="\"/usr/lib/ssl\"" -DENGINESDIR="\"/usr/lib/aarch64-linux-gnu/engines-1.1\"" The 'numbers' are in 1000s of bytes per…

Hi, I just bought a Rock Pi4B v1.4 recently. I tried to boot it with https://dl.armbian.com/rockpi-4b/Debian_buster_default_desktop.7z and https://dl.armbian.com/rockpi-4b/Ubuntu_bionic_default_desktop.7z However it was all in vain. I also had tried SDCard and emmc but none of them worked. Any suggestion? Thanks

Hi, I own a NanoPi M4 and I am wondering how to get the USB OTG working. I would like to set up Ethernet via USB OTG on my NanoPi M4. The only reference I can find is with https://vjordan.info/log/fpga/nanopi-neo-usb-otg-with-armbian-mainline-4x-kernel.html and I want to know if the steps are similar for NanoPi M4.

EDIT: Just realized I posted this in the bug tracker forum. My apologies! See:

I'm not sure this is right place to submit libgnutls30 armbian package issues. If anyone libgnutls30 to 3.6.7.4-deb10u9, you may have trouble to connect some SSL destinations. I revert it back to 10u7, then problem was gone. 20220817.05:18:10 root@armbianr2s:~/lkm# echo -e "GET / HTTP/1.1\n\n\n" | openssl s_client -connect web.telegram.org:443 -tlsextdebug CONNECTED(00000003) ^C 20220817.05:18:47 root@armbianr2s:~/lkm# #SSL_CONNECTION_PROBLEM_SOME_SITES_AFTER_UPGRADE_libgnutls30_THEN_REBOOT; 20220817.05:19:03 root@armbianr2s:~/lkm# #PROBLEM_ALSO_HAPPENED_WHILE_tcptraceroute_THEREFORE_I_WAS_REALLY_CONFUSED_AND_WASTED_TIME. BECAUSE, tcptrace and python N…

🏆 Become a sponsor, help to add other boards in armbian standart, you don't need to be a programmer to help the community, just need a copy of the ARM BOARD and a x86 computer to compile new versions. If you like what you see here and want to help: Donate Armbian the like button only costs a few dollars. Here, I will document the efforts to get the Easy EAI RV1126 board into Armbian. Uboot: Link boot: Link MiniLoaderAll.bin: Link Docs available on: Link Build Command: ./compile.sh BOARD=easy-eai-nano BRANCH=vendor BUILD_DESKTOP=no BUILD_MINIMAL=yes KERNEL_CONFIGURE=no RELEASE=resolute ./compile.sh BOARD=ea…

Hi all, is it possible to boot a Nanopi M4 V2 from a NVME M2 ?

hi, i have only one fan that spin, i have set the systemctl stop fancontrol and checked the pwm1 the value is 255, and only one who spin i can turn off the only fan spinning with value 0, but i can't control the seconds fan at all, i have verified the connectique on the board and everything is fine, when i opened it and checked without disk , and i saw that both fan was spinning, so i thought it was fine, when i closed the board and disk's are on, i again have the same issue, i can control only 1 fan, it's always the same one. any idea how to fix this issue? is it a software related?

I was getting kernel panics and discovered that my 32 GB Rock 5B Blue Edition just crashes when I try to malloc 8-9 gigabtes of memory. Is there a way to specify that this board has 32 GB ram? 5.10 works fine.

Title. Since apparently the proprietary drivers have better support for both. Thanks in advance.

Here's some photos of my M4 with SATA hat and 4 SSD's in a drive case - all working beautifully

Hello, I'm using Nanopi M4 installed Armbian Buster. It works like charm but I found a strange behavior of the system. In htop all cores are displayed as little core. but when I checked actual clocks in /sys/devices/system/cpu/cpu*/cpufreq/cpuinfo_cur_freq big cores are doing well (up to 1.8GHz). htop result: lscpu results: Architecture: aarch64 Byte Order: Little Endian CPU(s): 6 On-line CPU(s) list: 0-5 Thread(s) per core: 1 Core(s) per socket: 3 Socket(s): 2 Vendor ID: ARM Model: 4 Model name: Cortex-A53 Stepping: r0p4 CPU max MHz: 1800…

@Igor Kernel enabled Bootsplash works great on the recent 20.08 on Orange Pi 4. However there is a delay of around 20 - 30 seconds before this Bootsplash comes up. Is is possible to enable bootsplash on u-boot also on this image? I built a custom image 20.08-trunk with option "Kernel enabled bootsplash' disabled however could not see u-boot bootspalsh on this image. -Rajesh

I backed this early, and I have had nothing but stability problems since I built the thing. Sometimes my machine runs for as few as 6 minutes before crashing, and helpfully, it keeps clearing the systemd journal every time it starts up so I can't even see what happened just before it crashed. It crashes running OMV and Syncthing with high load, it crashes doing absolutely nothing but watching the systemd journal. It crashes doing nothing at all. When it crashes, it corrupts my files, and often the OMV Database requiring me to CONSTANTLY reset the GUI password for OMV, and then find that half of OMV isn't working. It does this on both uSD cards and on the inbuilt MMC.…

Hello, I have an ARMBIAN image 08.21.6 kernel 5.10.16 it works very well on rockpi 4B + rev 1.6 I tested the last Kernel but without more success. when we fix the ip address and we up (several times) the eth0 network this one puts to work at a time. Do you have an idea ? Regards.

My nanopi m4b has been showing slowness problems that I believe to be caused by the ethernet, I access a site inside it that has a camera stream and sometimes it is slow, and now the connection via ethernet completely stopped working, I looked for something in the logs but I didn't find anything that could indicate the problem, I can access my site over wifi

Hi, i use a Rock Pi 4b with a external USB3 Seagate 4TB HDD on USB3 Port on RockPi 4B. Der HardDisk ist ext4 formatet und mounted via fstab The maximum troughput over Samba Share is around 11 Mbit The same USB HDD on a Odroid with same samba settings has an troughput over 100 MBit Any Ideas ? Thanks Ingo

When using my (intel) laptop I get when I check my nvme (as root): # lspci -vvvs 01:00|grep -E "ASPM|L1" DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited LnkCap: Port #0, Speed 16GT/s, Width x4, ASPM L1, Exit Latency L1 <8us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ Capabilities: [900 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+ L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- L1SubCtl2: T_PwrOn=500us With the 6.1-…

Hey, I also wanted to use the Rockchip VPU inside my Jeyllfin docker-container. But on my machine (RK3389, 6.6.47-current-rockchip64, Armbian v24.8.4 bullseye), I only can only see "dri": ls -l /dev | grep -E "mpp|rga|dri|dma_heap" drwxr-xr-x 3 root root 120 Oct 18 11:18 dri How can I install the missing parts? All I found when googling was finding installing for ubuntu and not debian. For the required OpenCL (libmali) I used this: mkdir -p ~/tmp/libmali && cd ~/tmp/libmali wget 'https://github.com/tsukumijima/libmali-rockchip/releases/download/v1.9-1-55611b0/libmali-valhall-g610-g13p0-gbm_1.9-1_arm64.deb' sudo dpkg -i ./libmali-valh…

Hi, I had to change the Rack 1 HDD because I got an email telling me that this disk was broken. So I ordered new discs to make my replacement. When I put my new disk my problem started. For information my old disk was perfectly visible before I changed it and the led was functional too. I have a strange problem and I'm afraid it's hardware. Currently I have Rack 1 (HDD 1) which no longer detects my disks, there are no more LEDs lighting up, we can clearly hear the HDD lighting up, but it is not visible in the CLI and not via the WebUI. Im using OMV 6.x with kernel 5.15.89 (current) stable RAID 6 with 5 x 8To Have try…

I need to turn off the pwr_led light under the armbian system, thank!

Hello since kernel 6.12 led (heartbeat and mmc activity) on board rock64 don't work. I've created issue in dietPI github: https://github.com/MichaIng/DietPi/issues/7618 but DietPI is using armbian kernel. Now I'm using recent armbian with kernel 6.11.0-edge-rockchip64. Any idea how to restore led activity on recent kernels?

I have installed Armbian 21.02 Ubuntu 20.04 Focal with Linux kernel 5.10.16 and OpenZFS 2.0.1-1 on my Helios64. Created a three-disk encrypted RAIDZ pool with the following command: sudo zpool create -f -o ashift=12 -O compression=lz4 -O atime=off -O acltype=posixacl -O xattr=sa -O encryption=aes-256-gcm -O keylocation=prompt -O keyformat=passphrase tank raidz1 /dev/disk/by-id/foobar1 /dev/disk/by-id/foobar2 /dev/disk/by-id/foobar3 Then I did a single sequential read benchmark with fio on /tank: cd /tank sudo fio --name=single-sequential-read --ioengine=posixaio --rw=read --bs=1m --size=16g --numjobs=1 --iodepth=1 --runtime=60 --time_based …

Today I flashed the latest version CLI Jammy img instead of my old OS.First system boot,I can get the IP from my router DHCP and I can ping the Board's IP,but SSH connection refused.Now the Latest System won't start SSH service in first boot?I haven't a monitor,so I cant check the system booted or not.

Hi, I've flashed the Armbian SPI image following these instructions: https://wiki.radxa.com/Rock5/install/spi I've flashed this image: Armbian_22.11.2_Rock-5b_jammy_legacy_5.10.110_gnome_desktop.img.xz to a M.2 NVME SSD I own a DVB-S2 USB 2.0 device from PCTVSystems: https://www.linuxtv.org/wiki/index.php/Pinnacle_PCTV_DVB-S2_Stick_(461e) currently working in a RPi4 with OSMC. Firmware file (dvb-demod-m88ds3103.fw) is on /lib/firmware When I connect it to Rock5b I can see it with lsusb command Bus 002 Device 003: ID 2013:0258 PCTV Systems DVB-S2 Stick 461e and dmesg usb 2-1: new high-speed USB device number 3 using ehci-pla…