Rockchip

Hello I have installed Armbian 24.2.3 Bookworm with Linux 5.10.160-legacy-rk35xx on Orange Pi 5 plus with 32 Gb ram and mounted a heatsink with a fan on the CPU (this model: http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Cooling-Fan.html) I need help configuring the fan to turn on when the CPU temperature reaches 60°C and turn off when it reaches 50°C. Can you provide instructions on how to do this? Thanks for help or support

Hi all. Some time ago, in the release notes of a past Armbian version, I remember reading that the network LED should now be enabled by default and associated with eth0. Despite always keeping my Helios64 as up-to-date as possible, mine never lit up, but I didn't think much of it. Today I decided to investigate why, and I'm not sure where to go from here. First things first, the LED works, it's not a hardware issue. I can echo 1 and 0 to the LED path (/sys/class/leds/helios64:blue:net/brightness) and it lights on and off as expected. From what I can tell, this LED, along with the heartbeat one, is enabled by the Systemd unit helios64-hear…

I apologize in advance if I wrote to the wrong branch. Dear community, a question about OrangePi 5B (board without SPI-flash!). There is only an eMMC on the device. The computer is successfully running on the OS from the Orangepi website, recorded both on the SD card (Baleno Ether) and with eMMC (MaskROM+RKdevtool). At the same time, I see the devices themselves and their partitions, SD card and/or eMMC. The Armbian OS for OrangePi 5/5B/5 Plus (CLI or GUI) written to the SD card loads and works, BUT disk commands DO NOT SEE eMMC, only SD card partitions. In Armbian-config, there is only the Insatall/Update bootloader on SD/eMMC item, which does not change anything. If …

Hi, I bought a 2-pin piezo buzzer to use for alarm messages. It is connected to the P4 header on the board. When I execute the "beep" command in the console I only get short click noises. Are special kernel drivers necessary for a correct function?

Hi, I'm wondering if the NanoPi M4 can be made to work with a PiTFT 320x240 screen? When I set up the /dev/fb0 device and write to it, the display simply stays black/white (each time I write to the display only the shades change). NanoPi M4 has a different GPIO set-up from Raspberry Pi 3b+ (which PiTFT works with). Is there a possibility that the NanoPi M4's GPIO could be rewired in a way that it would support the PiTFT? E.g. Tinkerboard runs under RK3288 (vs M4's RK3399) and has the same GPIO layout as the RPi 3B+, so it could maybe be made possible?

Not sure if this is the place for this since it isn't really a software issue, but... So I decided to take apart my Helios64 to apply the 2.5Gb/1Gb Ethernet fix and things went badly. I ended up accidentally destroying the 402 caps on one of the SATA ports by scrapping the board against the standoffs as I was pulling it out of the case. As far as I can tell, they should be part of the SATA standard, 10nF DC blocking caps, so I have a rough idea of what they might have been but I don't know for sure since they are simply gone. Does anyone happen to know what those caps were or have access to a circuit diagram or BOM I could referenc…

I flashed a home built nanpim4v2 image to two brand new Silicon Power 32GB sdcards and they wont boot whereas SanDisk 32GB boot OK can anyone explain why ?

I have a strange problem with my R2S. I grabbed latest buster and focal images, burned them using Balena Etcher onto a pair of 32GB SanDisk Extreme Cards and neither is booting. Serial console shows that boot process gives up waiting for root file system and drops me into initramfs shell. Looking into /dev, I see no mmcblk0 device (or any other block device apart from loops). If I now eject and re-insert the card, the device shows up. If I do it during boot process, while the board is still waiting for rootfs, boot process continues correctly. Reboots are fine, but if I unplug the board for longer than a second it's back to initramfs for me. …

I have Rock64 board with latest Armbian Focal flashed on it. I want to use it with this HDMI display by Waveshare: https://www.waveshare.com/wiki/7inch_HDMI_LCD_(H)_(with_case) Now, when I connect it to Rock64 it runs as 1080p downscaled by HDMI controller on display, resulted image is garbage, even though it is present. As was discussed here: https://forum.armbian.com/topic/10071-tinker-board-hdmi-resolutions-do-not-all-work/ current kernel/u-boot doesn't have required video mode to run this display properly. I tried to set required mode with xrandr but with no success. Can anyone help me to figure out how to patch kernel/u-boot to get this thing work properl…

Hi. I am faced with the problem of installing overlays on Orange Pi 4. I need to use SPI and I use the following settings: verbosity=1 bootlogo=false overlay_prefix=rockchip rootdev=UUID=946e374a-7ca8-488d-ad86-ab38ccfc7cc1 rootfstype=ext4 overlays=spi-spidev param_spidev_spi_bus=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u As far as I know, after connecting the overlays, the devices should appear in the list / div, but this does not happen. New devices will not appear also when installing overlays w1-gpio or uart1 I also have problems with Ethernet connection if I use param_spidev_spi_bus=0, but if i use param_spidev_spi_bus=…

I have a development board, model eaidk-310, with soc rk3228h (which is said to be the same as rk3328). The official website of the board has been closed, so I cannot obtain more related information. However, I found the official firmware and can use rockchip's official tool for burning. The file structure is as follows. 190798 Jun 8 2020 MiniLoaderAll.bin 33554432 Jun 8 2020 boot_linux.img 374 Jun 8 2020 parameter-linux.txt 6815744000 Jun 8 2020 rootfs.img 4194304 Jun 8 2020 trust.img 4194304 Jun 8 2020 uboot.img parameter-linux.txt is: FIRMWARE_VER:8.1 MACHINE_MODEL:RK3328 MACHINE_ID:007 MANUFACTURER:Rockchip MAGIC: 0x5041524B…

Hi! I am working on a project in which audio is transmitted over the I2S bus to TAS6424-Q1 chips. I am using the Radxa Rock S0 board, the latest stable Armbinan 6.6 kernel and an additionally compiled dummy-codec module. 1. If I use the following overlay // Definitions for 8-ch-output /dts-v1/; /plugin/; / { compatible = "radxa,rockpis", "rockchip,rk3308"; fragment@0 { target = <&i2s_8ch_0>; __overlay__ { #sound-dai-cells = <0>; rockchip,clk-trm = <1>; status = "okay"; }; …

Would like to be running fail2ban but missing an important kernel module -> xt_multiport Any ideas on obtaining this? modprobe: FATAL: Module xt_multiport not found in directory /lib/modules/6.12.22-current-rockchip64

I'm getting burst "VOP vblank IRQ stuck for 10 ms" error messages in dmesg and wondering what it means and if anything to improve/fix. I'm using Nanopi m4 $ uname -a Linux nanopim4 5.10.21-rockchip64 #21.02.3 SMP PREEMPT Mon Mar 8 01:05:08 UTC 2021 aarch64 aarch64 aarch64 GNU/Linux kern :err : [Sat Mar 13 22:20:13 2021] rockchip-vop ff8f0000.vop: [drm:vop_crtc_atomic_flush [rockchipdrm]] *ERROR* VOP vblank IRQ stuck for 10 ms kern :err : [Sat Mar 13 22:21:04 2021] rockchip-vop ff8f0000.vop: [drm:vop_crtc_atomic_flush [rockchipdrm]] *ERROR* VOP vblank IRQ stuck for 10 ms kern :err : [Sat Mar 13 22:21:04 2021] rockchip-vop ff8f0000.vop: [drm:vo…

Hi, I've booted the board from SD card with the latest image and I'm trying to configure the board to boot from MTD and use USB drive as a system drive. When running armbian-config (or armbian-install, or nand-sata-install), it fails with error "SPI u-boot image not found!". It looks like the bootloader package is missing the /usr/lib/linux-u-boot-current-rock64_23.02.2_arm64/rkspi_loader.img. Can I find it anywhere? Dmitry

Hi my Helios 64 do not boot up anymore. In serial console i can see U-boot crc problem. So what can i do? Spoiler port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 1500000 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no hangup is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is : omap is : emap is : crcrlf,delbs, logfile is : none initstring : none exit_after is : not set exit is : no Type [C-a] [C-h] to see available commands Terminal ready T T DDR Version 1.24…

Hi All, Below command works well on my other boards(Intel with Fedora and Ubuntu) $ compton -b --backend xrender This command make windows background transparent so it doesn't hide lower window completely. But same command doesn't work on RK3288/RK3399 board. Any idea what should be done to achieve same. Does anyone have idea if anything customized in x-server related to this?

I have 2 issues in LibreOffice installed by default in Armbian, running on RockPi 4B. First: special characters aren't working. Second: filenames or folders using special characters are not recognized - therefore I can't access or edit my files, and even can't save files with special characters... anyone has a tip to solve these two issues? Thanks a lot

Hi, I owe a rockpi4a which I like to reflash with a custom build dev image: ./compile.sh BRANCH=dev RELEASE=buster BUILD_MINIMAL=yes BUILD_DESKTOP=no KERNEL_ONLY=no KERNEL_CONFIGURE=no BOARD=rockpi4a Can I flash this image directly to emmc, so it boots from it ?

Hi ! I spent several hours looking for the solution, here and elsewhere, I didn't find. The Radxa wiki speaks about 2 SPI: 1 and 2 The device tree README speaks about 4 SPI: SPI 0 pins (MOSI, MISO, SCK, CS): GPIO3_A5, GPIO3_A4, GPIO3_A6, GPIO3_A7 SPI 1 pins (MOSI, MISO, SCK, CS): GPIO1_A7, GPIO1_B0, GPIO1_B1, GPIO1_B2 SPI 2 pins (MOSI, MISO, SCK, CS): GPIO1_C0, GPIO1_B7, GPIO1_C1, GPIO1_C2 SPI 3 pins (MOSI, MISO, SCK, CS): GPIO2_B2, GPIO2_B1, GPIO2_B3, GPIO2_B4 So, the correspondence seems to be: radxa SPI 1 <=> DT SPI 1 radxa SPI2 <=> DT SPI 3 With the latest kernel (5.10.12-rockchip64, Deb…

How do you control which PHY the Rock64 is going to use? Android 9 is available for Rock64 now, https://github.com/a9rock64/manifests But it is configured to use the internal PHY and I need to change it over to the external one. Is this controlled in the DTS or someplace else? It is running on this kernel: https://github.com/rockchip-linux/kernel

hi, I am running newest armbian for NEO3. I've noticed that when I issue poweroff command armbian shuts down correctly, but the CPU (with heatsink) remains hot. I left my board for 2 days in poweroff state and it remained 'warm' all the time. Is there something that can be done to put CPU to sleep before shutting down system (or some low power state) ?

I am using native camera ( NDKCameraManager2 ) in c++. I wanted to know whether rk3399 supports camera2 HAL3 with LEVEL_3 or not? 我在c ++中使用本机摄像头（NDKCameraManager2）。 我想知道rk3399是否支持LEVEL_3的camera2 HAL3？

Hi there, I'm using the latest version of armbian to run the linuxptp for the ieee1588v2 clock. When I check the timestamp status, the 1Gbps port which is the RTL8122 is no problem, but the 2.5G ports RTL8125BG are only supporting the software timestamp. However, when I checked the Realtek website, it says that the 8125BG also supports the IEEE1588 clock. I tried to install the driver, but it did not work. As a beginner in Linux, I probably don't have the knowledge to compile drivers, in this case I sincerely hope that armbian could officially support the hw ptp timestamp in 8125 NIC. Thank you very much! nanopi-r6s:~:# ethtool -T end0 Ti…

Note that I want to use Hardware acceleration also later, but the issue is that it seems there's no HA for ffmpeg on the chip as you can see here. Thanks in advance!

https://www.armbian.com/odroid-m1/ - kernel 6.1.y LTS

We are facing some issue while interfacing 5" MIPI display to RK3399.

If someone of you likes karaoke I highly can recommend running UltraStar Deluxe (OpenSource SingStar clone) on the Rock Pi 4. https://github.com/UltraStar-Deluxe/USDX I‘ve used the Focal gnome desktop 5.10 image and built UltraStar Deluxe as described. Performance is very good!!! Even with 1080p videos I can‘t see a difference compared to my desktop pc. With the original wireless PS3 SingStar microphones this is a pretty nice and portable setup.

I'm trying to enable UART6, UART7, and UART10 via overlays on a sige5 board. UART6 AND UART7 are working fine but I'm not seeing UART10 in the /dev directory. Could someone help me debug this?

Hi, Is TrustZone being utilized at all? I can't seem to find any documentation on what execution level Kobal is running at during boot. I assume it's dropping the Kernel into EL2? Cheers

hi everyone How can I activate the SPI in the nanopi neo3 board?

Hi, I am strugling with the OV13850 camera on the NanoPC T4. Its working with the command : GStreamer 1.1 command: gst-launch-1.0 rkisp io-mode=4 path-iqf=/etc/cam_iq/rk-ov13850.xml ! video/x-raw,format=NV12,width=1280,height=720,framerate=30/1 ! rkximagesink But I can not connect to it through OepnCv VideoCapture cap(0) . or 1 2 3 . It give s error : VIDIOC_QUERYCTRL: Inappropriate ioctl for device Is there anybody experienced on this ? thx

Hello, target : nanopi R4S/4Gb I downloaded the last image from the armbian site for the friendlyelec nanopi RS4. I flashed an A1 SD card of 32GB. I only see one partition (after a 17MB offset). When I try to use it on my R4S, the red power led lights up, then nothing, even after several minutes. I opened the router and connected a serial converter on the console, in this case also there is no sign of life after the power on... I have flashed on another SD card an ubuntu image from the friendlyelec site. This image boots, but it seems that the configuration of the console is not the usual default one => the speed 115200 does not w…

Hi i have a orangepi 4 , i try install armbian mainline based kernel 5.4.y having issue with hdmi, no display, the os cant sense any hdmi connection. But when i try kernel 4.4 the hdmi work with? anyone having the sane issue?

Dear all I have a question concerning the Tinker Board video playback function. Until now I used some raspberry PIs 3b to create a simple system that video playbacks in loop after booting for my video installations. Now as the raspberries are not in stock at the moment but i need very urgently another working system, i saw that i can buy the tinker board 2.0 for a reasonable price. However, I'm not a programming specialist and was happy when I got the raspberry to run, I couldn't found anything about the tinker board and specially about a video loop function. I imagine that it is possible, just wondering how complicated it is. Can someone tell me …

Now I'm no expert but I got Mate working maybe there are some shortcuts I did not take, but it works great. So feel free to point out any flaws or improve it, #!/bin/sh -vx packages=' cryptsetup libblockdev-crypto2 engrampa firefox ffmpeg libavcodec-extra gufw lightdm lightdm-settings slick-greeter ubuntu-mate-wallpapers-common mate-desktop-environment-extras mate-applet-brisk-menu mate-applets mate-calc mate-indicator-applet ayatana-indicator-application ayatana-indicator-bluetooth ayatana-indicator-common ayatana-indicator-display ayatana-indicator-keyboard ayatana-indicator-messages ayatana-indicat…

TL;DR: How to make HDMI screen with custom resolution work? Including boot log/boot splash screen. How to configure auto use of/auto switch to newly connected display? Means moving tty/X Session to connected display like it works on e.g. Ubuntu desktop. Why HDMI screens with non standard resolution works well on kernel v5.x but stop working on v6.x ones? Where are HDMI related I2C interfaces in Armbian? Full version: In theory host system (SBC, laptop, PC) should detect new HDMI device connection, load EDID data from screen and use it to configure video output (resolution, timings etc). In practice it works well for Ubuntu deskto…

There is a uwe5621ds WiFi module on my rk3576 development board. I burned the system image of armsom-cm5-io. After booting, calling the modprobe sprdwl_ng command will encounter the following kernel pannic [ 71.088504] Unable to handle kernel NULL pointer dereference at virtual address 00000000000001d0 [ 71.089376] Mem abort info: [ 71.089655] ESR = 0x0000000096000004 [ 71.090002] EC = 0x25: DABT (current EL), IL = 32 bits [ 71.090490] SET = 0, FnV = 0 [ 71.090784] EA = 0, S1PTW = 0 [ 71.091069] FSC = 0x04: level 0 translation fault [ 71.091509] Data abort info: [ 71.091772] ISV = 0, ISS = 0x00000004 [ 71.092147] CM = 0, WnR = 0 [ 71…

I just received my Helios64, I immediately checked it for the Magjack center point to ground concern, and mine tests that it is connected. Is there a revision number on the board which can be used to identify the clean point between the pre and post fix boards?

Hi Distro Debian Buster, Linux rockpi-4b 5.10.21-rockchip64 #21.02.3 SMP PREEMPT Mon Mar 8 01:05:08 UTC 2021 aarch64 GNU/Linux I trying run HDMI-CSI bridge (auvidea B101) with board RK3399. Driver is loaded but dmesg not see any communications. root@rockpi-4b:/home/stream# lsmod |grep tc tc358743 40960 0 v4l2_dv_timings 36864 1 tc358743 v4l2_fwnode 28672 1 tc358743 videodev 299008 8 rockchip_vdec,v4l2_fwnode,videobuf2_v4l2,hantro_vpu,rockchip_rga,videobuf2_common,tc358743,v4l2_mem2mem mc 61440 7 rockchip_vdec,videodev,videobuf2_v4l2,hantro_vpu,videobuf2_common,tc358743,v4l2_m…

Libre Renegade overlays opp-1.4ghz and opp-1.5ghz load but not working in trixie edge (24.5.0-trunk.512). Both overlays do work in 24.2.1 bookworm.

Hello My Helios64 arrived two weeks ago, after a loooong trip through the Silk Road all the way down to South Europe. First thing I want to give a GREAT THANK YOU to the people at kobol shop support, as they have helped me with my transport/forwarded/ carrier nightmare loop: the address is in Chinese-no address specified-contact the sender-won’t give you your parcel-please call again- no address specified.... So. After reading a good slice of the wiki I couldn’t find a comprehensive manual/article about the simplest usage of the front panel. Glad if you can point me to such information. The principal source of confusion for me are the comments section of …

Hello, good morning from Spain. My sincere congratulations to the Kobol and Helios64 team. A really good and well designed product. I have a question about the compatibility of a hard drive with the Helios64 NAS. My hard drive is ---> https://www.senetic.es/product/0F38459 <--- ( Wd Ultrastar 18TB) With a capacity of 18TB, my question is: Is that hard drive (18TB) compatible with the Nas Helios64? I think that in the Nas Helios64 technical description, it only accepts a maximum capacity of 16 Tb hard drives Thank you very much for the information and help.

Hi everybody! I have been working for days to ensure that the MIPI-DSI output works with the Raspberry PI compatible display panel (Product OSOYOO which has a Toshiba TC358762 DSI/DP bridge chip and a I2C backlight controller as Focal FT5406). The following overlay works perfectly with the Radxa kernel 4.4.153 and unfortunately not with the Armbian kernel: Linux rockpi-4c 5.8.13-rockchip64. So far so good. Now if you look at the DTS source files of the two kernels, they have a similar structure but are very different in content. I wonder why you now get the idea to reinvent the wheel. The Radxa kernel contains everything that is needed. What is particularly ann…

I have Rock-5b with 6.2.0 kernel uname -a Linux rock-5b 6.2.0-rc1-station-m3 #23.06 But it does not contain some modules for multimedia USB devices, such as si2157. How can I install the sources, import default config for Rock-5b and build & install custom kernel? It's OK to build it natively on Rock-5B

Hi, To my side, below work in root but not with systemd service: # Helios64 PWM Fan Control Configuration # Temp source : /dev/thermal-cpu #INTERVAL=10 INTERVAL=30 FCTEMPS=/dev/fan-p6/pwm1=/dev/thermal-cpu/temp1_input /dev/fan-p7/pwm1=/dev/thermal-cpu/temp1_input MINTEMP=/dev/fan-p6/pwm1=40 /dev/fan-p7/pwm1=40 MAXTEMP=/dev/fan-p6/pwm1=50 /dev/fan-p7/pwm1=50 MINSTART=/dev/fan-p6/pwm1=20 /dev/fan-p7/pwm1=20 MINSTOP=/dev/fan-p6/pwm1=20 /dev/fan-p7/pwm1=20 MINPWM=20 To my side, below work in root and with systemd service: # Helios64 PWM Fan Control Configuration # Temp source : /dev/thermal-cpu INTERVAL=10 …

Hi armbian community, Does someone know, if it is possible to boot armbian from external ssd via usb using a NanoPi M4. If yes, is there somewhere a how-to? - I did not find anything so far about this topic. with best regards, newAB

Hello. I have this old rk3188 based board with 32gb rom 1gb ram. The arduino is attached for console output. I wanted to install linux in it so i flashed rk3188 armbian to my sd card and it was able to boot up from sdcard successfully. But there is no hdmi signal. I tried to modify dtb file extlinux.conf file but it didnt work. Can anyone figure out what is the problem? This is my extlinux.conf: LABEL Armbian LINUX /boot/zImage INITRD /boot/uInitrd FDT /boot/dtb/rk3188-rbox-cs968.dtb APPEND root=UUID=61de6b0d-dcd6-4049-9fe8-3a15872992b5 console=uart8250,mmio32,0x20064000 console=tty0 …

Can’t figure out how to enable SPDIF on NanoPi NEO3. rk3328-nanopi-neo3-rev02.dtb sources contain SPDIF sound-spdif { compatible = "simple-audio-card"; simple-audio-card,name = "SPDIF"; simple-audio-card,cpu { sound-dai = <&spdif>; }; simple-audio-card,codec { sound-dai = <&spdif_out>; }; }; spdif_out: spdif-out { compatible = "linux,spdif-dit"; #sound-dai-cells = <0>; }; ............ &spdif { status = "okay"; pinctrl-…

Hi, I have success boot armbian on MIQI Board, But I didt see emmc node on dev. So I cannt use dd to flash the emmc . root@miqi:~/repos$ ls /dev/ ashmem dri i2c-2 loop2 mapper network_throughput rtc tty0 tty16 tty23 tty30 tty38 tty45 tty52 tty6 ttyS0 usbmon1 vcs5 vcsa6 block fb0 i2c-5 loop3 mem null rtc0 tty1 tty17 tty24 tty31 tty39 tty46 tty53 tty60 ttyS1 usbmon2 vcs6 vhci btrfs-control fd initctl loop4 memory_bandwidth ppp shm tty10 tty18 tty25 tty32 tty4 tty47 tty54 tty61 ttyS2 v4l …

I'm a complete noob to compiling kernels and have been struggling (and failing) for the past week to get an RT kernel compiled using Armbian build and reading various threads in the forum. Is it even possible? If so, what config options need to be set to get the correct kernel version matching the available rt patches? Thanks!

Hi, I'm using a bananaPI m5 pro SBC with a rk3576 CPU and built-in emmc and linaro OS. I'd like to install minimal/IOT images using Armbian Linux v6.1. I went through all of the banana PI docs, but none of them contained any useful information about installing the OS and booting from SD cards. Can someone help me with this?

Hello, I am selling a working unit of Kobol Helios64 with the fix done, without drives. Based in Czech Republic, able to send within EU. Please DM me if interested.

Last night I shutdown my Helios 64 (sudo shutdown now) but when i went to boot it this morning, after startup it looks to be hung, all blue lights solidly on. It's set to run from the micro SD card, so wondering if i hit a R/W limit on that. Serial log below, it doesn't progress beyond "starting kernel" I can mount the MicroSD on my ubuntu box and read the file structure DDR Version 1.24 20191016 In channel 0 CS = 0 MR0=0x18 MR4=0x2 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x18 MR4=0x1 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channe…

I've installed Armbian_v22.05.2_Rockpi-4cplus_jammy_current_6.1.33_minimal and whatever I try to play a 1080p video via the performance is horrible with very slow refresh, totally unusable. Normally loki gives me acceptable performance on SBCs of similar performance but not in this case. The Rock 4c plus is quite powerful so I'm really shocked at how badly it's performing. Let me be clear, I understand that the issue I see is not that the Rock 4c plus isn't cable of playing video, clearly it is and I'm not complaining about the hardware of the device. It's just that the software being used clearly needs to be optimised for it and most things out th…

Orange Pi 5 pro,whith Armbian_community_26.2.0-trunk.7_Orangepi5pro_noble_vendor_6.1.115_gnome_desktop 。 when I try to start Eclipse/idea/vscode or other JavaApp , java processes crash and gets core dump every time, tested on Jdk 17,21 25 ,both openjdk and oracleJDK。 It seems there is a compatibility issue between the kernel and the JDK. How can I fix it? Or I have to wait kenel update? some error like Current thread (0x0000ffffa802b9b0): JavaThread "main" [_thread_in_vm, id=6202, stack(0x0000ffffaeb62000,0x0000ffffaed60000) (2040K)] Stack: [0x0000ffffaeb62000,0x0000ffffaed60000], sp=0x0000ffffaed5ce40, …

Hi, everyone. The Kobo site is kind of difficult to navigate if you're looking for relevant information, but I came to the conclusion that this is the right place for support. Forgive me if I'm mistaken. I was wondering if someone could help me interpret these bootlogs from serial term when trying to boot my Helios64 from the EMMC. Following the instructions on Kobol's site, I flashed their u-boot image to an sd card, booted the Helios64 off of said sd, fetched the latest image of Armbian, unpacked that image, and flashed it from my laptop to the Helios64 via usbc to what I presume is the correct interface. Could it be that I messed up? Here's a quick example …

I just bought one NanoPi M4 on FriendlyArm Black friday, I was wondering if the Raspberry Pi Oficial 7" display works with the DSI connect on NanoPi M4?

Hi, I am testing mesa panfrost on RK3399 and I am facing an odd problem. When joint the chroot as root I get mesa working but if I join as pi, the user, I cant get it working and I've receive just a soft render (llvmpipe) How this could be fixed?? any experience??

) my Setup is : **Board**: Helios64 (RK3399) - **Kernel**: `6.18.44-current-rockchip64` - **Armbian**: 26.8.3 (upgraded from 25.11.2 via apt) - **Boot**: currently booting from SD card (rootfs on mmcblk0); b) symptoms : After upgrading to 26.8.3, my drives are no longer detected — but only on a "warm reboot": - ASM1061 PCIe-SATA controller (bays 1-2) completely missing from `lspci` - JMS561 USB-SATA bridges (bays 3-5) missing from `lsusb` - Other USB devices (VIA hubs, Realtek USB NIC) enumerate fine - No `sdX` block devices at all in `lsblk` The only fix is a "cold boot": `poweroff`, unplug the power cable, wait 1-2 minutes, power back …

I am running last stable armbian with kernel 4.4.192-rockchip64 on emmc - really everything works nice (only thunderbird is very slow) - thx a lot for your work. The only thing I could not figure out, how I can wake up from suspend by keyboard or mouse. The armbian image uses org.freedesktop.login1.suspend to suspend - normally I am used to upower or pm-utils and there it was until now all the time possible to wake up with keyboard. Its quite uncomfortable to wake up the Rock64 with the power button - hidden, very small hole, I just use now a wooden chopstick for wakeup. Does anybody know, how to configure wakeup-hooks / wakeup-events for systemd …

Hi I have install the armbian system into my SSD device. But how can i manage to get it to start from that? The system dont seems to want to boot only from that SSD. I need to have the Micro SD inserted into the card reader for it to be able to boot. After that it seems to first boot up whit the SD card after that switch over to the SSD. How is that happening? NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 465.8G 0 disk └─sda1 8:1 0 461.1G 0 part /var/log.hdd / mmcblk0 179:0 0 29.8G 0 disk └─mmcblk0p1 179:1 0 29.5G 0 part zram0 2…

I have an Orangepi5 ultra RK5388. I have tried the following versions of Armbian13. It doesn't recognize my USBs so I don't have a keyboard. vendor: https://armbian.systemonachip.net/dl/orangepi5-plus/archive/Armbian_25.8.1_Orangepi5-plus_trixie_vendor_6.1.115_minimal.img.xz.sha This one won't start ,current: https://armbian.systemonachip.net/dl/orangepi5-plus/archive/Armbian_25.8.1_Orangepi5-plus_trixie_current_6.12.43_minimal.img.xz There is also no reference to Debian13 in any repository on the Orangepi website.

On an OrangePi-5b, `apt-get update` a few days ago updated the kernel, and now bluetooth no longer works. What's the proper way to downgrade the kernel to whatever I had before? (armbian-config shows way too many options)? Better yet, get it working again? bluetoothctl does not see the controller at all, and dmesg gives the following: $ dmesg|grep -i bluetoo [ 2.796188] Bluetooth: Core ver 2.22 [ 2.796203] NET: Registered PF_BLUETOOTH protocol family [ 2.796206] Bluetooth: HCI device and connection manager initialized [ 2.796211] Bluetooth: HCI socket layer initialized [ 2.796214] Bluetooth: L2CAP socket layer initialized [ 2.796220] Blue…

I want to share a solution to a problem that I had: Problem: The problem was that no HDDs nor JMB585 were being detected. If I run the `lspci -nn`, it would show no devices: # lspci -nn And there were some `PCIe link training gen1 timeout` in the kernel messages. root@helios64:/home/amreo# dmesg | grep -Ei 'sata|ahci|scsi|ata|sas|sd[a-z]|helios' [ 0.000000] Machine model: Kobol Helios64 [ 0.000000] NODE_DATA(0) allocated [mem 0xf77c6800-0xf77c8fbf] [ 0.000000] printk: log buffer data + meta data: 262144 + 917504 = 1179648 bytes [ 0.016416] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.022065] Memory: 3778312K/4061184…

Hey there, I just joined the ARM universe & to be honest I lost all my skills with Linux. First I tried some official images Armbian_22.11.1_Rockpi-4cplus_jammy_current_5.15.80_xfce_desktop.img & with all of them I got a Blackscreen after the Logo. (all settings were made) Then I a tried a pre-release so I could finally get into armbian. Wifi : I couldn't connect via. wifi, "wifi network could not be found" But it was listed with a good signal strength. BT: no adapter was found. ( I used armconfig to enable BT) USB: just 3 of 4 usb ports were working. ( I guess it was 1x usb 3.0 & 2x usb 2.0) The Rock P…

Brand new out of box, the wireless works fine on the orange android os. I then downloaded the orange os aarch64 image and installed. It was the latest. Wireless did not work, but after a couple lines of code/commands it did. I had to add a line to the orangepienv.txt file that was dealing with overlays. After that and a reboot it worked fine. BUT it is seriously boxed in. That is, because of lack of aarch64 support I could not download what I needed...so I tried debian which worked ok, but had issues with processing streaming video over 480p...anything higher I was having screen stutter and ripping plus their was artifacts everywhere. Finally I settled on Armbian,…

I am trying to extend the chipselect from spi4. Because I will need to control more boards, so I tried to transform GPIO into chipselect (CS). This is the original SPI4: /dts-v1/; / { fragment@0 { target = <0xffffffff>; __overlay__ { status = "okay"; #address-cells = <0x01>; #size-cells = <0x00>; pinctrl-names = "default"; pinctrl-0 = <0xffffffff 0xffffffff 0xffffffff>; spidev@0 { compatible = "rockchip,spidev"; …

Dear all, i have been using Armbian bionic currently running kernel 4.4.156-rockchip64, for sharing files over the internet, i am currently using sshfs. Openssl benchmark ls as followed OpenSSL 1.1.0g 2 Nov 2017 built on: reproducible build, date unspecified options:bn(64,64) rc4(char) des(int) aes(partial) blowfish(ptr) compiler: gcc -DDSO_DLFCN -DHAVE_DLFCN_H -DNDEBUG -DOPENSSL_THREADS -DOPENSSL_NO_STATIC_ENGINE -DOPENSSL_PIC -DOPENSSL_BN_ASM_MONT -DSHA1_ASM -DSHA256_ASM -DSHA512_ASM -DVPAES_ASM -DECP_NISTZ256_ASM -DPOLY1305_ASM -DOPENSSLDIR="\"/usr/lib/ssl\"" -DENGINESDIR="\"/usr/lib/aarch64-linux-gnu/engines-1.1\"" The 'numbers' are in 1000s of bytes per…

Hi, I've flashed the Armbian SPI image following these instructions: https://wiki.radxa.com/Rock5/install/spi I've flashed this image: Armbian_22.11.2_Rock-5b_jammy_legacy_5.10.110_gnome_desktop.img.xz to a M.2 NVME SSD I own a DVB-S2 USB 2.0 device from PCTVSystems: https://www.linuxtv.org/wiki/index.php/Pinnacle_PCTV_DVB-S2_Stick_(461e) currently working in a RPi4 with OSMC. Firmware file (dvb-demod-m88ds3103.fw) is on /lib/firmware When I connect it to Rock5b I can see it with lsusb command Bus 002 Device 003: ID 2013:0258 PCTV Systems DVB-S2 Stick 461e and dmesg usb 2-1: new high-speed USB device number 3 using ehci-pla…

Hello, after some u-boot test, my helios64 don't start the bootloader stage. I can etablish a serial connection on USB Type-c port, but when I tried to start the system, I have no output on it. After I disconnected everything : - I connect usb-c cable, I'm able to connect to serial console with picocom - I connect the power cable, The LED1 (System Rail Power) is on, and the LED9 (Battery Status) flashes. - I press the power botton (without sdcard) : - LED2 and LED3 (Periph. Rail Power and HDD Rail Power) are on - LED4 and LED5 (System ON and HDD Activity) are on. - nothing happen on serial console - If I keep SWI (power …

Hi! How can I install the edge kernel while still being able to boot armbian and keeping the built-in wireless module working? Is there any firmware for this module at all for kernel 6.2?

That newsletter indicated that USB-C to HDMI cables promised were still delayed. Is there an update on that? Thanks!

The rock pi 4 is no longer on the download page? https://www.armbian.com/download/?device_support=Supported&tx_maker=radxa&arch=aarch64 There is no rock pi 4 link any more?

Hey guys, So I wanted to update the OS on my NAS to patch the Copy Fail vulnerability today. I installed everything, I also did an apt-upgrade (not a full one) to make sure my kernel was as up to date as I could get it, and I also updated the initramfs, too. Now when I boot up the Kobol, I can hear the disks spinning up after a few seconds upon powering up, they make an odd noise and then just stop. The LEDs on the front panel also no longer show blue anymore, and `fdisk -l` no longer shows anything. I know for a fact these HDDs are not dead. They have worked perfectly fine before the upgrade, and the SATA pins look perfectly clean. I e…

Hi Armbians I have a problem with one of my NanoPi Neo 3 boards and dropped RX packages on eth0. From multiple Neo 3`s I have running, this is the only one having this issue. But its also the only one with 1GB of RAM. All other boards have 2GB of RAM. But this should not matter I think. Output ifconfig: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet XXXXXXXXXX netmask 255.XXXXXXX broadcast XXXXXXXXXX ether XXXXXXXXXXX txqueuelen 20000 (Ethernet) RX packets 140166777 bytes 110091299296 (102.5 GiB) RX errors 0 dropped 3686 overruns 0 frame 0 TX packets 12724…

I have a 4G Rev 2 Rock64 that is running like a champ on current - 5.4.2 as of this writing, as far as USB and Ethernet are concerned. I did have to blacklist UAS for all my USB drives, and now the board is rock solid even with heavy disk and network IO. I do have one problem though, I have no sound. I have the following loaded (automatically): root@chdock:/home/sugata# cat /proc/modules |grep snd snd_soc_rk3328 16384 0 - Live 0xffff800008dc9000 And yet, I get this: root@chdock:/home/sugata# aplay -l aplay: device_list:272: no soundcards found... I searched around this forum and nothing obvious came up. Any ideas?

Has anyone been able to install a remote desktop on the R2S? If so I would be very interested in how that was achieved?

Hi all Been playing with this rockpi s bluetooth . I noticed debian kernel 5.x and bluetoothctl, just hangs. No issues with debian kernel 4.x. Anyone else had this, and able to get it to work?

Device: Orange Pi 5B OS: Armbian 23.5.0-trunk.135 Bookworm Pipewire devices listed using pactl list sources only lists a single input device, which I think corresponds to the headphone jack input device. There should be 2 input devices, one for the onboard MIC and one for the headphone mic. When trying to test the onboard mic with arecord -l the audio is completely silent which indicates that the only device enumerated by arecord actually corresponds to the headphone MIC Unforunately, I don't recall if the original OrangePi OS had both mic options listed or not, but I can check if necessary. Has anyone previously teste…

On a Rock 5B, I installed Armbian 23.11 Bookworm CLI via a SD card and now trying to setup boot via the NVMe drive. I followed the instructions on https://www.armbian.com/rock-5b/ to create a partition on the NVMe drive, format it, then tried `armbian-install` to boot from SPI. However armbian-install does not list the option to "Boot from SPI". It shows only the following options: 1 Boot from SD - system on SATA, USB, or NVMe 5 Install/Update the bootloader on SD/eMMC I then noticed I do not have a SPI device. /dev/mtdblock0 doesn't exist as well as "cat /proc/mtd" is empty. # ls /dev/mtd* ls: cannot access '/dev/mtd*': No such file …

EDIT: I hate to have to admit this, but I completely forgot that the nanopi m4 v2 needs external antennas for its wifi to operate properly. (I bought just before the coronavirus hit, and it was several weeks before I got back to setting up the board. First board I've had that needs that.) Having terrible troubles getting a working wifi on various Armbian OSes on nanopi-m4v2. Tried: Armbian_20.05.1_Nanopim4v2_bionic_legacy_4.4.213_desktop.img Armbian_20.02.7_Nanopim4v2_buster_legacy_4.4.213_desktop.img (Armbian_20.05.2_Nanopim4v2_focal_current_5.4.43_desktop.img - just won't boot, as of 24h ago) Armbian_20.05.2_Nanopim4v2_bus…

Hi, I noticed that on my board I didn't have notification with MOTD when updates were available and I think that I've found the culprit: In the file /usr/lib/armbian/armbian-apt-updates of the package linux-buster-root-legacy-nanopim4_20.08.17_arm64.deb, this line stop the script to go further : # give up if packages are broken [[ ! $(dpkg -l | grep ^..r) ]] && exit 0 If I remove the ! then it works (because the script, in fact, gives up if packages are not broken )

Hello, With the new version for rockpi 4 (Buster Kernel 5.X). I put in my armbianEnv.txt: overlays=uart2 console=display my ttyS2 has a very weird permission compared to other, (on the other hand I don't have this problem at all on a 4.X kernel) crw-rw---- 1 root dialout 4, 64 Dec 23 14:00 /dev/ttyS0 crw-rw---- 1 root dialout 4, 65 Dec 23 14:00 /dev/ttyS1 crw--w---- 1 root tty 4, 66 Dec 23 14:01 /dev/ttyS2 crw-rw---- 1 root dialout 4, 67 Dec 23 14:00 /dev/ttyS3 crw-rw---- 1 root dialout 4, 68 Dec 23 14:00 /dev/ttyS4 crw-rw---- 1 root dialout 4, 69 Dec 23 14:00 /dev/ttyS5 crw-rw---- 1 root dialout 4, 70 Dec 23 14:00 /dev/tt…

Hello everyone. I have a defunct Helm Email server which carries a Rockchip rk3399 SoC. I have flashed with a custom Armbian image provided by the Helm folks. After flashing the box with the .img file, I am able to ssh into the new armbian box and go through the basic initial armbian setup. The box recognizes my 1TB nvme drive, so I then create a primary partition and format the nvme using fdisk and mkfs. I then install armbian-config and use it to install the root system to the nvme0n1p1 by using the following option on the menu: System -> Install -> 1 Boot from SD, and chose the nvme0n1p1 partition. After that I verify the BootE…

This is a work-in-progress resource for bare-metal bringup for Rockchip devices. Source code: https://github.com/petabyt/rk https://danielc.dev/rk/

Hello, Since few days, my PSU makes a high-pitched noise. As my NAS is installed in my living-room, it is annoying. I have changed my PSU three weeks ago, it was good during these three weeks, but it comes suddenly noisy... Does anyone else has the same issue ? And any ideas on how to fix this ? Thanks

My question to the developer: Is there any probability that the native ethernet (gigabit) connection will be working in the future? I think that's the main advantage of the rock64 board (gigabit ethernet AND usb 3.0). Otherwise many other boards will work as well as NAS as the rock64. Thanks in advance for answers!

I have a nanopi m4 and I want to use the /dev/ttyS4 (UART4) for communication, but only the RX is working, and the TX does not, but when I set the GPIO nr. 40 (the TX pin) to output through sysfs I can change the voltage level from high to low and back... Please help, what am I missing here, that I can not transmit anything ? I am using the latest friendlycore.

Greetings everyone, I am new to the forum. I have recently completed an initial boot of Armbian 20.11.3 (stable) which appeas to be Debian Buster under the skin. I have a Sabrent 256GB NVME ready to go (works on other Rk3399 boards and my Pinebook Pro). I am booting from a 64GB uSD card. Using Armbian-config, I was able to update my board's SPI u-boot to mainline and rebooted to confirm I didn't mangle the SPI. The next step was to run the nand-sata-install.sh script to get it to copy the root and boot filesystems onto the NVME drive. While everything has worked so far and I copied the latest nand-sata-install.sh script from Github yesterday (when…

I saw the official document of NEO4 that FriendlyDesktop had full hardware acceleration support, including video decoder, opengl, built-in Chromium browser, etc. So does this ARMBIAN NEO4 have the same complete hardware acceleration support?

Any guesses whats wrong? The bootup stucks at [ 311.991668] random: crng init done for such a long time with 5.4.49... That happend on two different ROCK PI 4B 4GB v1.3 with SPI and NVME SSD boot without SD/eMMC. (fdtfile=rockchip/rk3399-rock-pi-4.dtb). It is only happening if I disconnect power and boot up. It seems working fine if I just restart the board. No problems with 4.4.213 Kernel (fdtfile=rockchip/rk3399-rockpi4b.dtb). It was also working fine with an older version of 5.4.xxx... channel 0 CS = 0 MR0=0x98 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 CS = 1 MR0=0x18 MR4=0x2 MR5=0xFF MR8=0x8 MR12=0x72 MR…

I have the Rock64 4G Version with emmc module Since the latest Kernel Update two weeks ago on friday the board does not boot up anymore. (I was on Stretch initially and updated regularly since.) Even with a newly flashed sd card and without emmc module the board will not but into armbian. I managed to boot into raspbian buster 5.91 once, but after rebooting it, it failed again and stayed that way. until now I have tried the latest 3 images. The Kernel is now 4.4182 and is unchanged whatever I do. with any armbian on an sd card i am getting: Failed to start armbian zram config - failed to start journal service Failed to flush Journal to Persi…

When comparing network speeds on the orange pi 3b 8gb model using armbian (Jammy Gnome 6.8.2) and Opios (aarch64-xfce-opi3b-23.08.1-linux5.10.160), there seems to be an issue with uploads on armbian. Using iperf3 for testing, the results were as follows: For orange pi os (arch): From other device (server) to orange pi 3b (client): 112mb/s From orange pi 3b (server) to other device (client): 112mb/s For armbian: From other device (server) to orange pi 3b (client): 112mb/s From orange pi 3b (server) to other device (client): 42mb/s I would like to know the cause of this problem and how to solve it.

Hello, we have a strange thing here. Since ... (I don't remember), the tray number 2 is not working. We tried with 3 different disks but each of them, when inserted in tray n2, aren't start. Why ? And how to fix that ? Thank you. PS: other trays (n1, n3, n4, n5) are ok.

I have completed a build for the turing-rk1 SBC with an aim toward getting a functioning graphical console, and possibly installing desktop packages later. I built an image without issue that picked up kernel 6.17.2. git commit: 09160da3b9c1231cf20837e8c857f7e605130449 main branch Command used: ./compile.sh RELEASE=trixie CARD=turing-rk1 BRANCH=edge Image created: Armbian-unofficial_25.11.0-trunk_Turing-rk1_trixie_edge_6.17.2.img When booted, I get an error from dmesg about VOP drivers and HDMI video does not turn on. Is this normal for this board or am I doing something wrong? [ 0.965616] rckchip-drm display-subsystem: [drm:rockchip_d…

Hello everyone! I have an issue with rebooting my orangepi 4. when i use tf card, reboot is working. but when i using system in emmc, the board can't reboot. the output from debug ttl is like this: [ 41.329350] watchdog: watchdog0: watchdog did not stop! [ 42.148627] xhci-hcd xhci-hcd.5.auto: Host halt failed, -110 [ 42.170221] gpiod_set_value: invalid GPIO (errorpointer) [ 42.188751] xhci-hcd xhci-hcd.5.auto: Host halt failed, -110 [ 42.189252] xhci-hcd xhci-hcd.5.auto: Host controller not halted, aborting reset. [ 42.190309] reboot: Restarting syste

Looked at a lot of other forums posts and it seems to be a common problem for the Orange pi 5B, but all the solutions i've tried hasn't worked. Most of the problems they seemed to have is not updating the armbianEnv.txt to include the "b" for this specific model from the opi 5. Below is the error message I always get whenever trying to boot from the EMMC. Using 6.1 kernel sometimes I can't see the EMMC in /dev, after installing the orange pi Ubuntu image I can see it. After I run armbian-install I can't see it in /dev. I put the orange pi image back on the sd card and I can see the EMMC was installed, the boot/armbianEnv.txt also does have the "b". …

Current issues with Armbian board support: -U-Boot problems (various) Solutions so far: - fix the method of generating idbloader.bin. <--- update: the "release" and "mainline-master" behave significantly differently. Mainline-master behaves as it should as far as writing the bootloader. Release does not.

Hi, I want to use the I2S GPIO output pins on Nanopi m4 to connect to multi channel DAC. Unfortunately I can not see it as a playback device: user@nanopim4:/home$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: realtekrt5651co [realtek,rt5651-codec], device 0: ff890000.i2s-rt5651-aif1 rt5651-aif1-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: rockchiphdmi [rockchip,hdmi], device 0: ff8a0000.i2s-i2s-hifi i2s-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Is there a way to enable I2S output on GPIO? 36 | I2S0_SDO0(1.8V) 37 | I2S0_SDI1SDO3(1.8V) 38 | I2S0_SDI2SDO2(1.8V) 39 | …