Rockchip

It does not matter which of the lastest Images I am downloading for the NanoPC T4, none of them is showing any sign of boot sequence. I flashed the images with balena etcher to the SD-Card before. I thought writing the image with etcher to SD-Card is all I need to do. My old system Shaitan with OMV is booting from SD-Card witout any issue. I have no idea, why none of the newer Images escpecially for the NanoPC T4 is not booting at all. Does someone has any idea?

i am trying to enable touch for the 8 inch display on your build, the display is from radxa, and after enabling the hadware configuration and enabling rock-5a-radxa-display-8hd from the menu, the display is working perfectly, but the touch isnt working, i was searching the official build for the touch related sources, the touch is controlled by godot GT911 driver IC, its using i2c for touch, https://forums.raspberrypi.com/viewtopic.php?t=284882 how do i get this to work on your image? attached are images on radxa images for rock 5a

Hello Each time I try to upgrade to kernel 6.6.39 on a rockpi-4a the system become unbootable: ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Loading Ramdisk to f01f6000, end f1f0Ad94 ... OK Loading Device Tree tn 00000000f0179000, end 0000 000f01f5fff ... OK Starting kernel ... efi_free_pool: illegal free 0x00000000f0f0d04 efi_free_pool: hllegal free 0x00000000f0f0a040 I have another rockpi-4a but with a rockpi4b image (installed by mistake) I was able to copy the file 6.6.32 from this system to my other one (creating the older symlink on /boot) , and I have be able to boo…

is it intended to integrate openzfs-2.0.0 and if so, is the timing already known?

I installed Armbian on my R5s Armbian 23.8 Bookworm Kernel 6.5, Size: 479Mb, Release date: Sep 18, 2023 On this version, I find the classical problem : a module I want to build does not build. Reason ? apt says : Coundn’t find any package by glob ‘linux-headers-6.5.3-edge-odroid’ And make creates an error because “build” directory is not found. I can find the linux-headers-6.5.3 : https://cdn.kernel.org/pub/linux/kernel/v6.x/linux-6.5.3.tar.gz But where can I find the odroid version ?

I have a nanopi m4 and I want to use the /dev/ttyS4 (UART4) for communication, but only the RX is working, and the TX does not, but when I set the GPIO nr. 40 (the TX pin) to output through sysfs I can change the voltage level from high to low and back... Please help, what am I missing here, that I can not transmit anything ? I am using the latest friendlycore.

I have a jammy Armbian install on one of the (really) new IndieDroid Nova devices. I have changed /etc/gdm3/custom.conf, setting AllowRoot=true and /etc/pam.d/gdm-password, disable root quiet setting. Typical of what you do for Debian to enable explicit user/password input of the Gnome greeter. But with Armbian jammy, I still only get the default 'ttt' user forced on me, and the only value I can enter is the password for ttt. How to get the user list to appear so I can select ANY user and enter the password?

I have a rock 4b+ and I used it as an android box for a while. Then today I tried to flash it with latest armbian image (23.8.1) and it does not boot in microSD or when I flash it through USB OTG. I have erased the SPI flash completely and install the correct spi_loader. It also boots properly with Radxa debian image. Initially I though this is a boot issue, but after checking with a serial cable, it turns out this is a HDMI issue.. After I finish the usual procedure to setup password etc... I got this: Now starting desktop environment... root@rockpi-4b:~# [ 633.211385] hdmi-audio-codec hdmi-audio-codec.5.auto: Only one simultaneous stream su…

I'm working on enabling secure boot on Orange Pi 4B. So far I was able to burn eFuses, sign rk loader, a trust image, and a uboot image. To extend secure boot chain to the Linux Kernel, I've enabled FIT_SIGNATURE in u-boot, and manually built FIT image (Linux Kernel, initramfs(initrd), and a kernel DTB). Now I want to add FIT image creation to the Armbian build system. What is the correct place/script to do it?

Hi there, So I'm having a problem connecting the helios to the router. I try different lan cables and different ports. It was working everything fine yesterday, I did a reboot and no more connection. I'm completely new to this. I was installing home assistance and plex before this happened but I believe I didn't mess with anything to do with network. Don't know what I might have done. I can connect to helios via putty and after logging in the part where ip should be there is none. Any advise would be most appreciated. Again I'm completely new to this.

It seems a package is missing from the Armbian 23.8 Bookworm CLI that results in this error. I encountered an add-apt-repository: traceback error. To fix it just run: sudo apt install python3-launchpadlib

I upgraded from my own-compiled Armbian kernel 6.8.0-rc5 to 6.8.4 and there are now very annoying stall when for example I drag a KDE Konsole window. Also when I play a 1080p50 HEVC video, as son as a move the mouse, the whole video stalls. Besides 6.8.0-rc5, the normal apt provide 6.8.1-edge-rockchip-rk3588 also works OK. 6.8.5 has the same issue as 6.8.4. As indicated, I use KDE, X11, compositor disabled. Enabled makes no difference. OS base is Armbian Bookworm, but I have also used kernels 6.8.1 and 6.8.4 with a rootfs copied from an RaspberryPiOS and Opensuse-Tumbleweed. RPiOs is also Debian Bookworm, Tumbleweed is latest, KDE6. So it is not KD…

Hi all! Is it possible to configure Orange Pi 4 wifi to work in AP mode ? Will both 5ghz and 2.4 ghz be supported ? Thanks for advance in answer.

OS: Armbian_22.11.0 (5.15.71) for RockPi-4C HW: RockPi-4C I would like shared my eth0 connection via integrated wlan0 adapter. I have do all steps stated here: https://linuxhint.com/create-wifi-hotspot-linux-mint/ but when I try to connect my notebook to the hotspot wlan, notebook does not get proper IP address and so a internet sharing does not work . Any ideas to solve this problem?

I hope I am posting this in the right forum ? Just installed Armbian 22.05 Jammy XFCE. No audio either from the main board jack or the HDMI. Tested by playing mp3 with MPV and Celluloid as well as with Chromium Capture from armbianmonitor - U attached below or here http://ix.io/457n Any hints would be appreciated...I don't know how to investigate further this. No_Audio.txt

Hello, I had a NanoPi M4v2 running 5.10.63 (buster) for a while without issue. Both I2C and SPI were working perfectly fine and the system was stable. Today apt updated the kernel to 5.15.25 and it broke multiple things, the first issue was that the network wasn't working properly, yellow light but not green one / no IP requested from the local DHCP server. The overlays on this system were: overlays=dwc3-0-host i2c7 i2c8 spi-spidev overlays=dwc3-0-host i2c7 i2c8 spi-spidev I connected the eMMC moule to a card reader and removed the overlays one by one and found out that `i2c8` was breaking my boot / network: overl…

@prahal There are two versions of the bootloader in the repository (edge and current). I just tried the current u-boot from the repository. It works but dmesg outputs seven of the following messages: [ 9.674633] rockchip-i2s ff8a0000.i2s: Could not register PCM This note mentions that such error messages could mean that DMA and sound are missing in the linux kernel, could this be ignored ? P.S.: Those messages are not thrown if the recommended bootloader (linux-u-boot-edge-helios64_22.02.1_arm64) is flashed to emmc.

Hi, I have troubled to set an u-boot environment variable of NanopiM4V2. I have tried changing the rootdelay parameter by making /etc/fw_env.config file. However, I don't know how to get the number I have to write in it. NanopiM4V2 is booted from microSD card. ("cat /proc/mtd" is none) If anyone know how to set the /etc/fw_env.config file with booting from microSD card??

Hi all, does anyone know of a good reliable way to flash an image to a FriendlyElec type eMMC card, originally I used their microsd adapter but for some reason my PC / Transcend adapter doesn't recognise them anymore.

My OPI will turn on but it shows android os via hdmi. I don't have a micro SD card and would like to install bullseye via usb instead. i've attempted ssh into the OPI via wifi and direct usb connect, but it denies the connection. I have the OPI on wifi and can see it on my network. i've tried using android adb to no use. is there a way to install armbian WITHOUT using a micro SD at all?

Hello! Id like to use UART1 in NanoPi R2s , but i cant turn on it in armbian-config. There is only UART4.

Would it be easy to port Armbian on the Pipo M6 Pro and integrate additional device drivers to provide support for the touchscreen, the front and back camera and the sound? https://www.geekbuying.com/item/Pipo-M6Pro-GPS-Android-4-2-RK3188-Quad-Core-1-6GHz-Tablet-PC-9-7-inch-Retina-Capacitive-Touch-Screen-2048-1536-2GB-16GB-319264.html Is this something feasible in the first place? Anybody out there who want to help me on this project?

I had one OPi5 setup and working properly with one of my TVs. I was running Kodi and using the remote from my TV to control Kodi using HDMI-CEC. I went to setup a second one on another TV but this time the TV remote did not work properly. Through elimination I came to determine the HDMI cable was the issue. I ordered another HDMI cable that had the Ferrite at each side of the cable. Now it worked properly. Thought this might be useful for others. This is the cable I ordered: https://www.amazon.ca/dp/B003PDHJ6M Conclusion: In order to make HDMI-CEC work properly, make sure the HDMI cable is of sufficient quality. I think ones with the Ferrite may be b…

We are evaluating many boards for Industrial purpose, often fails to pick the right one, form Raspberry PI to other boards, including Tinkerboard. We aim to bring the cost of the SBC to 60 to 100 USD, mainly used for Industrial, within 0-70 Deg C. In fact, I have posted similar questions to find out answers, including Rock64, Olimex etc. Olimex seems to be supporting Industrial temperature, but their A64 seems to have less USB ports. Many SBCs vendor advertise their board for Education, Hobby purpose, I see Nano PC boards, they advertise for robotics, Industrial purpose http://wiki.friendlyarm.com/wiki/index.php/NanoPi_M4 with WIKI stating worki…

Nanopi Neo 3 is typically offered in 1GB or 2GB DDR4 RAM versions, but the RK3328 datasheet says the RK3328 can support up to 4GB If I were to source 2x 2GB of the supported types could I resolder to increase RAM? Official product page : https://www.friendlyelec.com/index.php?route=product/product&product_id=279 RK3328 Datasheet : https://rockchip.fr/RK3328 datasheet V1.2.pdf Neo3 Schematic : https://wiki.friendlyelec.com/wiki/images/a/ae/NanoPi-NEO3-2005-Schematic.pdf could anybody identify the chipname of the 2GB DDR 4 ram on the board?

Hi all, been trying to sort out a stability problem with what was a rock solid helios64, i moved from running armbian on the eMMC to a 256GB sandisk extreme SD card due to plex continually filling it up. currently running Armbian 21.05.6 Buster with Linux 5.10.43-rockchip64, running OMV, Plex and ZFS not much more it appears this is where things go pear shaped: Spoiler [ 6636.457621] ata1.00: exception Emask 0x2 SAct 0x3800000 SErr 0x1000400 action 0x6 [ 6636.458306] ata1.00: irq_stat 0x08000000 [ 6636.458659] ata1: SError: { Proto TrStaTrns } [ 6636.459051] ata1.00: failed command: READ FP…

I'd like to build a portable LimeSDR Transceiver. I would like to use a USBC 1080p IPS touchscreen. Has anyone had any experience with USBC touchscreens with the RK3399 SBC ?

Hey folks, So here's the setup I have: I have an Orange Pi 4B running the Orange Pi 4 image and kernel 5.6.17-rockchip64. I have an Orange Pi 4 running the Orange Pi RK3399 image and kernel 5.4.26-rockchip64 (cause when I got it, the Orange Pi 4 images weren't out yet). The OPi4 is running just fine. I imagine that I'm running the wrong DTB and that not all the hardware is working properly -- but the hardware I need is working just fine. The OPi4B is another story. It'll boot just fine, and it'll run just fine for days/weeks on end -- as long as I don't put it under any sort of heavy CPU load. But if I start running anythi…

Please, I need an img of Armbian compatible with the following: RK3399T and with HDMI. I have tried all versions of Armbian and they do not work. Some do, but the problem is that it does not display an image. I believe it could be the HDMI. The most preferable versions for me are Armbian Noble or Bookworm. The problem also occurs during updates. After updating, the wireless does not work. If there is a version with this fixed, I would be grateful if someone could post a version for me, as up-to-date as possible. My Radxa is a Rock Pi 4Plus v1.73. With a 256GB microSD, I need an img of Armbian that is compatible with wireless and HDMI. If anyone can send me the link, I wou…

Hi guys , I installed the Buster WIP image on my M4 V2 and it appeared to be functioning ok wifi,USB etc all working until this morning. It wouldn't boot so I connected a serial cable and saw where it failed ( I think it part of the uboot process) ERROR: Did not find a cmdline Flattened Device Tree Any ideas why this should suddenly happen ? I have two V2's running this build and the other is still working fine

Hi all, I've been away for a while - is the version shown below the latest for the NanoPi M4 V2 ? Linux M4V202 4.4.213-rk3399 #23 SMP Sat Mar 28 16:58:50 CET 2020 aarch64 aarch64 aarch64 GNU/Linux

Today I decided to update my kernel to 6.3.9 with the mainline ubuntu kernel/ppa https://ubuntuhandbook.org/index.php/2020/08/mainline-install-latest-kernel-ubuntu-linux-mint/ However this does not work if you have disk-encryption . After rebooting and being greeted by enter your password, it did not work claiming its missing the dm_mod module. This is the device-mapper module needed by cryptsetup to create a device in /dev/mapper/ After running unmkinitramfs on the 6.3.9 kernel /usr/lib/modules/6.3.9/kernel/drivers/md/dm-mod.ko was indeed missing. Is this normal for mainline ubuntu kernels ? and does anyone know how…

I'm working on a project using the nanopim4v2-current image. I noticed an issue with the available HDMI output resolutions. Only a select few resolutions are available, despite the connected screen advertising support for additional ones. I was also unable to output a custom resolution (for example 1920x538) by adding the proper modeline in manually through xrandr. I've been looking into this for a bit and managed to find a partial solution in Miouyouyou's recent pull request "[RFC] RK3288 : Add HDMI resolutions". Adding the patches to my build enabled support for my monitor's native resolution (1920x1200) and allowed me the ability to output custom resol…

I have the latest revision of the armsom sige 5. This board has an updated Wi-Fi chip set. It was changed from RTL wireless to a Broadcom chip connecting to the rk3576 with SDIO 3.0. I grabbed the latest Armbian image and it appears in the device tree It is still referencing the RTL Wi-Fi device. has anyone encountered this and found a solution? Or has gotten Wi-Fi working? I’ve attached the device tree. sige5.dts

Hello, I have installed the "Armbian_community_25.2.0-trunk.124_Tinkerboard-2_bookworm_current_6.6.63_minimal.img.xz" image on my tinkerboard-2 to develop a library for one wire devices. There is a problem with the usage of armbian-config on activating overlays. The entry in armbianEnv.txt includes the prefix in the overlay name. This can be workarounded manually, e.g. for w1-gpio the correct entry needs to be: overlays=rk3399-w1-gpio2 If anyone can point me to the source code I maybe can provide a PR to fix it. Another problem is the content of the overlay of this w1-gpio. After activating the dmesg give an error (the first w…

Hello. I have not been able to make the ethernet port working on a MKS Pi board with the latest armbian image found here : https://www.armbian.com/mks-pi/ I don't even get a link led ON on the ethernet connector when connected. Can anyone offer guidance? Thanks! P.S. I could not find a MKS-PI tag in the tag menu to identify this thread correctly. Can anyone fix this?

Hi, I have an issue with an USB device which is not detected; looking on other forum, it seems that additional modules shall be added: - cdc_acm,cdc_ether - rndis_host - rndis_wlan - usbnet I'm not able to load these using the modprobe cmd & checking loaded modules with lsmode cmd. I suspect that they are not part of the kernel. Any hint how to solve this, eventually recompile / install ? Thanks by advance, Samuel

I always received beacons with Country "US", until I created the file "brcmfmac43456-sdio.xunlong,orangepi-4.txt". It is a copy of brcmfmac43456-sdio.txt and I added the line: ccode=DE With this modification, I see the expected beacon. (Country: "DE", correct tx-power, ...) I think this is not the intended way to configure it. What I checked before: My hostapd.conf contains; ... country_code=DE ieee80211d=1 ... iw reg get global country DE: DFS-ETSI (2400 - 2483 @ 40), (N/A, 20), (N/A) (5150 - 5250 @ 80), (N/A, 20), (N/A), NO-OUTDOOR, AUTO-BW (5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS, AUTO…

Could anyone help me to enable display with Armbian? I just can’t figure out why it doesn’t work. I don’t see the backlight turning on either. What do I have to change? I have tru to add a custom dts on kernel but don't work

RockPi 4 Model C support will come in the near future?

Hi, I'm wondering if the NanoPi M4 can be made to work with a PiTFT 320x240 screen? When I set up the /dev/fb0 device and write to it, the display simply stays black/white (each time I write to the display only the shades change). NanoPi M4 has a different GPIO set-up from Raspberry Pi 3b+ (which PiTFT works with). Is there a possibility that the NanoPi M4's GPIO could be rewired in a way that it would support the PiTFT? E.g. Tinkerboard runs under RK3288 (vs M4's RK3399) and has the same GPIO layout as the RPi 3B+, so it could maybe be made possible?

Hi, I am posting this here to notify you about the serious networking performance issue on my Rockpi 4B board. Ever since I installed the Trixie release, the networking on the board has been poor/not working at all. I cannot even run an apt update If I try to connect via SSH, I get: root@rockpi:~# apt update 0% [Connected to github.armbian.com (185.199.110.153)] [Waiting for headers] [Waiting for headers]client_loop: send disconnect: Connection reset >ssh root@192.168.0.200 ssh_dispatch_run_fatal: Connection to 192.168.0.206 port 22: Connection timed out I don't know where to start / what to check here. When I turn on the board, it wo…

Hello guys, does anyone activated CVBS output on Rock64 board? After a short look into datasheet Rock64 should support 480i and 576i. Many thanks.

Has anyone made WiFi adapter MT7601u to work with Rockchip64 as AP? I'm unable to compile the driver. I've tried: https://github.com/muratdemirtas/MT7601u https://github.com/Vyacheslav-S/mt7601u-AP https://github.com/Anthony96922/mt7601u-ap I've installed current headers, build-essential libncurses-dev bison flex libssl-dev libelf-dev. Any help appreciate it.

I have the Helios64 NAS and am now at the point where I'll either get it working or toss it out and get something else.... it boots and runs and stops most of the time let's get some of the basics out of the way so we can figure out if here is the "best" spot to get help... uname -a returns root@helios64:/home/rmleonard# uname -a Linux helios64 5.10.21-rockchip64 #21.02.3 SMP PREEMPT Mon Mar 8 01:05:08 UTC 2021 aarch64 GNU/Linux cat /etc/os-release root@helios64:/home/rmleonard# cat /etc/os-release PRETTY_NAME="Debian GNU/Linux 10 (buster)" NAME="Debian GNU/Linux" VERSION_ID="10" VERSION="10 (buster)" VERSI…

I'm trying to setup disk encryption, but for some reason its not opening devices after installing cryptsetup-bin on the installation image. After typing the password it just hangs and does nothing $ cryptsetup open /dev/sda sda_crypt Anyone?

First of all, I would like to express my gratitude to the maintainers for their contributions. This project has helped me a lot, and it runs smoothly on my device. It seems that the status of the nanopi-r5s has been in the staging phase for a long time. I am wondering if there is an opportunity for it to be promoted to the standard support phase. Additionally, I would greatly appreciate having a compiled version of Ubuntu Server. Is there anyone willing to help with this? Thank you very much.

Looked at a lot of other forums posts and it seems to be a common problem for the Orange pi 5B, but all the solutions i've tried hasn't worked. Most of the problems they seemed to have is not updating the armbianEnv.txt to include the "b" for this specific model from the opi 5. Below is the error message I always get whenever trying to boot from the EMMC. Using 6.1 kernel sometimes I can't see the EMMC in /dev, after installing the orange pi Ubuntu image I can see it. After I run armbian-install I can't see it in /dev. I put the orange pi image back on the sd card and I can see the EMMC was installed, the boot/armbianEnv.txt also does have the "b". …

Hiya peoples, Finally figured out what caused my black screen after updating After installing a new kernel (via apt) the '/boot/dtb' symlink is not updated, and fails to boot properly. lrwxrwxrwx 1 root root 31 Oct 7 11:38 dtb -> dtb-6.11.2-edge-rockchip-rk3588 lrwxrwxrwx 1 root root 38 Oct 7 08:49 Image -> vmlinuz-6.11.2-current-rockchip-rk3588 lrwxrwxrwx 1 root root 38 Oct 7 08:49 uInitrd -> uInitrd-6.11.2-current-rockchip-rk3588 So I wrote a systemd service that: 1. Runs before shutdown/reboot 2. Changes into the /boot directory 3. Reads the version from the dtb symlink 4. Reads th…

Hello everybody, Is it possible to use the box with another card (odroid n2 for example)? Thanks a lot

I have several orange pi 5B running Armbian Bookworm Cinnamon doing various task and they are working quite well. when i want to check up on a system that was booted without a monitor connected at boot time i get no video output on the HDMI. when reboot with the HDMI connected the HDMI outputs video just fine. Are there any settings i can change so the HDMI will output video if a HDMI monitor is connected it boots with no monitor connected

Hi, I'm looking for the headless version of stretch and xenial for the rock 64. I only see the gui versions of strtech and xenial on the website. I got a special download from Igor a couple days ago but it has some strange issues so I was hoping to find a release version to try. Thanks! Mark

Hi all i tried to compile BTT CB2 with bookworm and vendor kernel to get MPP and NPU working, but got that : sha256sum: config/kernel/linux-rockchip64-vendor.config: No such file or directory is it missed ? How to compile vendor kernel for MPP support? thanks

Hello, When it's planned the support of wakeonlan? I want to keep my nas powered off, and power it trough a raspberry pi when I need It. Do you think is planned on the next days or in the next mounths? Thanks

Here's a video of GQRX receiving NOAA Weather Radio on my NanoPC-T4 armbian-nanopc-t4-gqrx-gnuradio.mp4

I’m using an Android TV Box X96 X6. Right now, I want to find a way to install Armbian on it, but I haven’t been able to figure it out yet. I’d appreciate any help or guidance from the community.

Hi folks I'm running a fresh install of the Debian branch with 5.X Kernel branch. I got 2 new 4TB HD setup with MDAM in RAID 1 mode to store my photo and documents with Syncloud also running on the HELIOS64. I Got also a 2,5 Sata drive mount and share via Samba to my home network. My Helios64 is plugged via the 2,5GB Ethernet port directly to my Router on the 2,5GB port. I didn't fix the hardware bug, but if I understood it's not necessary in my case ( 2,5GB Ethernet on a 2,5GB Ethernet Router) My problem is that on the same router I got an Apple TV (on ethernet port too) with Infuse app on IT. And there is the problem I got big…

After installing the hardware and software, my hdd 1 is inactive. I swapped my disk 1 and 5, 1 is still inactive. I checked my connections in the box but I don't see any problems. Could this be due to a software error?

I'm trying to get this rockpro64 board to boot off of pxe/nfs. I'm able to get it to boot into armbian and to the point where it asks for the new root password. But something happens on the device where the network gets disabled which stops the NFS connectivity and the rest of the system with it. All traffic stops on the device and it becomes unreachable. NFS traffic stops, it no longer responds to pings, etc. It's not entirely frozen, for example it prints kernel messages to console if the ethernet is pulled. And after a few minutes the nfs connection times out and it starts printing this over and over. It always happens about 75 seconds…

I've done quite a bit of searching and can't find anyone else reporting this specific issue. As the title says any 6.8 image I try fails to boot. The LED is red for approx 4 seconds, turns green for 2 or 3 seconds, and then turns red again and stays that way no matter how long I wait. There is never any video regardless of which HDMI port I use. I've tried the following images: Armbian_24.8.0-trunk.85_Orangepi5-plus_noble_edge_6.8.12_gnome-oibaf_desktop.img.xz Armbian_24.5.1_Orangepi5-plus_noble_edge_6.8.10_gnome-oibaf_desktop.img.xz Armbian_24.5.1_Orangepi5-plus_noble_edge_6.8.10_xfce_desktop.img.xz Armbian_24.5.1_Orangepi5-plus_bookworm_edge_6.8.10…

Hi, I'm struggling to get some sound through a PCM5102a module connected to GPIOs. I guess I've to make a dts-overlay to enable it on i2s0 but I didn't succeed, I'm very new to that. Could anyone tell me how to achieve that ? Many thanks for your work !

I have a rock5b running Armbian_23.02.2_Rock-5b_jammy_legacy_5.10.110_gnome_desktop.img Recently, somehow the kernel become corrupt in some manner. I restarted the board and it just never booted again. Blue light stays lit, never flashes. I am in the process of attempting recovery following the guide here: https://docs.armbian.com/User-Guide_Recovery/ however I get a little lost once downloading the required files, considering the naming scheme is a bit different and file locations are different. Currently I have downloaded: armbian-firmware_23.02.2_all.deb and linux-source-legacy-rockchip-rk3588_23.02.2_all.deb Can someon…

For a few Weeks i have little problem with my Nano Pi M4. Whenever I boot up it says: "Loading, please wait...starting version 237" and then i have to wait . Finally it boots up, but there were times this SBC was booting really fast. Is there something i could do, to speed up booting again? Regards

When I reboot with kernel 6.8.4 (edge) installed by apt upgrade, I noticed my scripts that uses snapper for remove differential backups. It turns out that, if no cleanup algorithm option is used, snapshot is created. Before the reboot, with kernel 6.8.1 version, there was no issue. I on Armbian Bookworm, but also with other Debian Bookworm based OS running those same kernel binaries. Same failure with 6.8.5 Currently I don't know any more, I could run this faulty kernel in a VM as the .config is such that it also boots on virt hardware (virt-7.2 as Bookworm uses). EDIT: Also in a VM, the problem is there: root@armbian64:/tmp# sn…

Hi, I had to change the Rack 1 HDD because I got an email telling me that this disk was broken. So I ordered new discs to make my replacement. When I put my new disk my problem started. For information my old disk was perfectly visible before I changed it and the led was functional too. I have a strange problem and I'm afraid it's hardware. Currently I have Rack 1 (HDD 1) which no longer detects my disks, there are no more LEDs lighting up, we can clearly hear the HDD lighting up, but it is not visible in the CLI and not via the WebUI. Im using OMV 6.x with kernel 5.15.89 (current) stable RAID 6 with 5 x 8To Have try…

Hello, as said in the title The latest Armbian 23.11 images don't display anything but it seems to start well. Is it possible that this is incompatible with my screen?

Hello Guys, I would like to have question maybe unwise but it's hard to find information about it. I would like to prevent somehow my Helios64 or it's power supply to minimize risk of fire. Do you have any propositions to minimize that risk? Thank you for your help in advance

Dear all, Has anyone tested using Wifi‘s AP and Station at the same time? I checked the info of wifi on this NanoPi M4V2 board with command: sudo iw list. the infomation of this wifi: .... valid interface combinations: * #{ managed } <= 1, #{ P2P-device } <= 1, #{ P2P-client, P2P-GO } <= 1, total <= 3, #channels <= 2 * #{ managed } <= 1, #{ AP } <= 1, #{ P2P-client } <= 1, #{ P2P-device } <= 1, total <= 4, #channels <= 1 .... This information shows it support the AP and station at the same time, but I only find a create…

Board: NanoPC-T4(rk3399) OS: Welcome to ARMBIAN 5.69 stable Ubuntu 18.04.1 LTS 4.4.167-rk3399 In VLC preferences, i have set video output to OPENGL ES(and here OPENGL ES is soft link to libMali.so). In short hardware accelerated Rendering. Problem Statement: When a video file is played in fullscreen mode it works perfect. But as soon as other x-window(for eg: small sized terminal window) comes in front of this fullscreen window, tearing effect starts. Now i don't understand why this happen. Whether it happens due to libMali and X-server Glamor compositing or something else. i don't have full understanding of linux graphics stack. …

Hello, we have a strange thing here. Since ... (I don't remember), the tray number 2 is not working. We tried with 3 different disks but each of them, when inserted in tray n2, aren't start. Why ? And how to fix that ? Thank you. PS: other trays (n1, n3, n4, n5) are ok.

I can use echo 0 >/sys/class/leds/status/brightness to turn off the status led (blinking blue one, but I was to turn off the bright ass green one. I assume this is mmc1::, but I cannot turn it off.

(Note: this is crossposted from an ATS issue, since I think it might be quicker to get answers here. Will post on one thread when I get answers that work in the other) Have installed ats on my Rock64, running Armbian 22.05 Jammy with kernel version 5.10.63, and am having trouble getting the fan to spin. The fan I'm using is the one that comes with this case, and it spins when I connect it to a battery. One possible issue is that I had to manually add an entry for PWM_CTL: running sudo find /sys -name pwm\*, I get: /sys/kernel/tracing/events/pwm /sys/kernel/tracing/events/pwm/pwm_apply /sys/kernel/tracing/events/pwm/pwm_get /sys/kernel/debug/tracing/events/p…

Hi I have install the armbian system into my SSD device. But how can i manage to get it to start from that? The system dont seems to want to boot only from that SSD. I need to have the Micro SD inserted into the card reader for it to be able to boot. After that it seems to first boot up whit the SD card after that switch over to the SSD. How is that happening? NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 465.8G 0 disk └─sda1 8:1 0 461.1G 0 part /var/log.hdd / mmcblk0 179:0 0 29.8G 0 disk └─mmcblk0p1 179:1 0 29.5G 0 part zram0 2…

[22787.457010] Internal error: Oops: 0000000086000004 [#1] PREEMPT SMP [22787.457594] Modules linked in: xt_nat xt_tcpudp veth xt_conntrack nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlinks [22787.465404] CPU: 1 PID: 609416 Comm: kworker/u8:5 Not tainted 6.1.11-rk35xx #23.02.2 [22787.466103] Hardware name: Radxa ROCK3 Model A (DT) [22787.466552] Workqueue: ext4-rsv-conversion ext4_end_io_rsv_work [22787.467107] pstate: 804000c9 (Nzcv daIF +PAN -UAO -TCO -DIT -S…

I just received my Helios64, I immediately checked it for the Magjack center point to ground concern, and mine tests that it is connected. Is there a revision number on the board which can be used to identify the clean point between the pre and post fix boards?

Hello I need to change a drive in the Helios64, and so I bought a new WD 2TB drive. Using a WD My Book 111D USB enclosure, I have partitioned, formatted and copied the data from the old drive. But when I change the drives to put the new one in the Helios64, the drive appears unformatted. See below. I can't understand what's happening, when I plug it back through USB everything is back to normal. Does the partitioning through USB differ somehow??? It appears as if the partition table "stays in the USB enclosure", which doesn't make sense for me. Is there something to try? Do I have to start again the process in the NAS enclosure? I…

I enabled spi-spidev through armbian-config but it does not show in the /dev/ directory. How do i fix this?

The Radxa bullseye image looks to boot fine, but Armbian forky does not boot at all.

hi, i have only one fan that spin, i have set the systemctl stop fancontrol and checked the pwm1 the value is 255, and only one who spin i can turn off the only fan spinning with value 0, but i can't control the seconds fan at all, i have verified the connectique on the board and everything is fine, when i opened it and checked without disk , and i saw that both fan was spinning, so i thought it was fine, when i closed the board and disk's are on, i again have the same issue, i can control only 1 fan, it's always the same one. any idea how to fix this issue? is it a software related?

I have a ROCK 3A that reaches Maskrom/recovery but will not boot any Radxa or Armbian SD image and produces no useful UART output. UART is configured per Radxa docs at 1500000 8N1 on the debug header, and the exact same adapter/host/settings work on another ROCK 3A. There is no eMMC and no NVMe installed. I also tried resetting/loading SPI via Maskrom using rkdeveloptool db rk356x_spl_loader_ddr1056_v1.12.109_no_check_todly.bin, then loading Radxa’s rock-3a-spi-image-gef9f6b1caad.img. Radxa’s ROCK 3A loader directory contains the matching SPI artifacts, including rock-3a-spi-image-gef9f6b1caad.img, rock-3a-idbloader-gef9f6b1caad.img, and rock-3a-u-boot-gef9f6b1caad.itb, a…

Hi folks, I am wondering if somebody with a mac enviroment has a decent / performant samba connectivity? After I upgraded to Big Sur I have severe issues with the samba protocol when accessing my shares on the helios running openmediavault. I know that Apple had made some changes with samba but there might be some users that dug a little bit deeper and could give me a hint. I did try it with different settings in the extra options over the past weeks but with no luck so far. Sidenote: Also NFS is terribly slow and laggy. I am back with AFP connection now that does the job perfectly and fast.

Good evening, I have a Rock64/4G board and just downloaded and installed the Armbian_5.42_Rock64_Debian_stretch_default_4.4.124_desktop.7z to the SD card. After the reboot I saw X11 login interface and everything was great. After that I installed the latest packages with an apt update and then apt upgrade and restarted. Now I only see "rock64 login:" on the screen. The Xorg.0.log I have attached looks actually quite good. Xorg.0.log

How do you control which PHY the Rock64 is going to use? Android 9 is available for Rock64 now, https://github.com/a9rock64/manifests But it is configured to use the internal PHY and I need to change it over to the external one. Is this controlled in the DTS or someplace else? It is running on this kernel: https://github.com/rockchip-linux/kernel

Hi, my current CI build fails, and i cannot make up, whats wrong with it. It was working previously until i moved my project within the GitLab instance to another folder. Now i'm getting the following errors: tail output.log OBJCOPY lib/efi_loader/dtbdump.efi CC lib/vsprintf.o CC lib/strto.o CC lib/abuf.o OBJCOPY lib/efi_loader/initrddump.efi CC lib/date.o CC lib/rtc-lib.o CC lib/elf.o AR lib/built-in.o [ error ] ERROR in function compile_uboot [ functions/cli/cli-entrypoint.sh:109 -> functions/main/build-tasks.sh:261 -> functions/main/build-tasks.sh:128 -> functions/compilation/uboot.sh:13…

I've been playing around with the 3d hardware acceleration on jammy, so I can use KODI without stuttering. And that works fine although the KODI version is a bit outdated. So I installed it doing this, under root: add-apt-repository ppa:liujianfeng1994/panfork-mesa add-apt-repository ppa:liujianfeng1994/rockchip-multimedia apt update apt dist-upgrade apt install mali-g610-firmware rockchip-multimedia-config but how do I revert: apt purge --yes mali-g610-firmware rockchip-multimedia-config apt autoremove --yes apt dist-upgrade --yes add-apt-repository --yes --remove ppa:liujianfeng1994/panfork-mesa add-apt-repository --yes --r…

I don't have a NanoPC-T4, but I have a NanoPC-T6 which I mainly bought because of the Dual Camera options of the MCAM400 on the T4 and the high-speed encoding properties of the Rockchip... those possibilities should be very similar for the T6 actually... Whatever, the camera configuration seems to be mostly here but I struggle to do the similar thing with the device tree of the T6... Anyone who has an idea about this and is willing to help me with that?

https://rosenzweig.io/blog/a-panfrostian-october.html The dev machine they used seems to be a rk3399 based chromebook. Looks like they will get a working panfrost after all!

Hi, the rockchip64 missing the gre modules for ipv4 and ipv6. they had been existing in 4.4.156-rockchip64 /lib/modules/4.4.156-rockchip64/kernel/net/ipv4/gre.ko /lib/modules/4.4.156-rockchip64/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko /lib/modules/4.4.156-rockchip64/kernel/net/ipv4/ip_gre.ko /lib/modules/4.4.156-rockchip64/kernel/net/netfilter/nf_conntrack_proto_gre.ko /lib/modules/4.4.156-rockchip64/kernel/net/ipv6/ip6_gre.ko is it possible to add these? thx in advance meno

I see that there is a lot of work ongoing on improving the UEFI boot support for Rock 5B and this is quite exciting. In my view this seem to be the ideal route for future SBC boards. However, I am yet to try it so I am still a novice in the area. How do you guys look at the future of UEFI vs U-boot for Linux on SBC’c in general and on the Rock 5B in particular? Will the UEFI version be as capable as a u-boot version or do you see limitations?

Has anyone here tested the Rock64 successfully with an u-boot version which is not the one from ayufan? I did not have much luck with the rk3328 default config and mainline u-boot when I tried it a while back. The same is true when I tried to use the board config from ayufan with mainline u-boot. The version by ayufan is working in principle but also is rather dated as far as I know and therefore does not support some newer features. Anyone knows if the version from ayufan will be bumped or has a working config for a more recent u-boot version?

I have a 4G Rev 2 Rock64 that is running like a champ on current - 5.4.2 as of this writing, as far as USB and Ethernet are concerned. I did have to blacklist UAS for all my USB drives, and now the board is rock solid even with heavy disk and network IO. I do have one problem though, I have no sound. I have the following loaded (automatically): root@chdock:/home/sugata# cat /proc/modules |grep snd snd_soc_rk3328 16384 0 - Live 0xffff800008dc9000 And yet, I get this: root@chdock:/home/sugata# aplay -l aplay: device_list:272: no soundcards found... I searched around this forum and nothing obvious came up. Any ideas?

I use orangepi 4B. I use console Ubuntu with kernel 4 from Xunlong And my CPU Temperature (by htop) is about 70°C I use console armbian with kernel 5 (Governor = powersave). And my CPU Temperature is about 79°C Why so? I want to get 70°C in armbian too.

lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 11 (bullseye) Release: 11 Codename: bullseye hwinfo --disk 20: PCI 00.0: 10600 Disk [Created at block.245] Unique ID: wLCS.EJHvc9MwvZ7 Parent ID: VCu0.AxGd7hiuG+6 SysFS ID: /class/block/nvme0n1 SysFS BusID: nvme0 SysFS Device Link: /devices/platform/f8000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/nvme/nvme0 Hardware Class: disk Model: "Samsung Electronics NVMe SSD Controller SM981/PM981/PM983" Vendor: pci 0x144d "Samsung Electronics Co Ltd" Device: pci 0xa808 "NVMe SSD Controller SM981/PM981/PM983" …

Hi i have a orangepi 4 , i try install armbian mainline based kernel 5.4.y having issue with hdmi, no display, the os cant sense any hdmi connection. But when i try kernel 4.4 the hdmi work with? anyone having the sane issue?

I have successfully built 21.08 and 22.02 branches for miqi (rockchip) with EXTRAWIFI=no only, but unfortunately 23.05 build fails with error: arm-linux-gnueabihf-gcc: error: unrecognized -march target: armv5 arm-linux-gnueabihf-gcc: note: valid arguments are: armv4 armv4t armv5t armv5te armv5tej armv6 armv6j armv6k armv6z armv6kz armv6zk armv6t2 armv6-m armv6s-m armv7 armv7-a armv7ve armv7-r armv7-m armv7e-m armv8-a armv8.1-a armv8.2-a armv8.3-a armv8.4-a armv8.5-a armv8.6-a armv8-m.base armv8-m.main armv8-r armv8.1-m.main iwmmxt iwmmxt2; did you mean ‘armv4’? arm-linux-gnueabihf-gcc: error: missing argument to ‘-march=’ Is there a way to get this to c…

In page station m2 -armbian say: Important. For the new images to work, it is necessary to update the u-boot in eMMC on M2\P2. The new version of u-boot is compatible with the existing official versions of Station and Ubuntu, which are released by Firefly. To upgrade to the new version of u-boot, you need to follow several steps. 1. Download a special version of the image from the link. download link but the download link: Nothing found There's a typo in the link, or the owner deleted the files or restricted access to them. Please update the download link，thanks！

What gives with the Armbian website links? Links to all previous versions Armbian for the OrangePi R1 Plus LTS have been removed. The links to SHA hash and PGP signature do nothing. I was hoping to use an image that was based on Debian Bullseye, but that link has been recently removed. It is possible to create my image, but I would spend my time working on my code, not wading through the options to create an image.

I installed panfrost but glxinfo still lists the device as llvmpipe. I'm using Armbian_23.02.2_Rockpi-4cplus_jammy_current_5.15.93_gnome_desktop running wayland. This is how I built panfrost meson . build/ -Dvulkan-drivers= -Dgallium-drivers=panfrost -Dllvm=disabled ninja -C build/ ninja -C build/ install i have no idea what to do next because there is no errors that I can find and I was under the impression that with a kernel 5.1> it is supposed to work. Any help is appreciated

Hi guys, can anyone give me a link as to where I can download a working image for the new Nanopim4 v2 - the friendly arm download section is very confusing - it states there is an eMMC image but when I downloaded it it didn't contain a *.img file that I could flash but a lot of other *.gz *.img files e.g. boot.img etc etc

My Orange Pi 4B has gone to community support. After an overheat with a compilation, the ssd dies, and I reflashed to the new community version Armbian_community_24.8.0-trunk.399_Orangepi4_noble_current_6.6.40_gnome-oibaf_desktop Anyway I got no HDMI output so I left it running, and suddenly I got a new device on the network. Since I am going to use it headless it works well for me. Bug 1 No HDMI Expected HDMI output works Actual Result No HDMI output. Bug 2 The second was when I downloaded llvm compiler normal output from clang compiler: (took the whole day yesterday to compile from source without overheating) clang++…