Allwinner sunxi

I am working on a project with armbian 23.8.1 embedded in a banana pi m2 zero. I need to use the spi 0 with the two select chips. When I initialize I can only initialize spidev0.0 or spidev 0.1. There is no way that can initialize both. Configure the armbianEnv.txt file with the following parameters: overlays= spi-add-cs1 spi-spidev param_spidev_spi_bus=0 param_spidev_spi_cs=1 Also try other combinations and nothing. Then try to modify the .dtb file by adding cs-gpios and changing status = "okay" but it doesn't work

I want to use the OPI3, but I need 2 uarts, in 26 headers there is 1 availabe, but I need one more. Is possible to disable the debug, and use it for my application?

I have board which has 2 slaves on the SPI bus, requiring ce0 and ce1. My system: Armbian 23.8.1 Bookworm with Linux 6.1.47-current-sunxi I applied overlays: spi-add-cs1 and spi-spidev, there's an spi in the system. As soon as I apply spi-double-spidev-bus.dts, the spi disappears. Скрытый текст /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target = <&spi0>; __overlay__ { #address-cells = <1>; #size-cells = <…

Hi all, I have a Nano Pi Neo Core board with Armbian 5.15.93, and I want to upgrade it to 6.1. I ran the "armbian-config", and selected the new version linux-image-edge-sunxi=23.02.2 based on kernel 6.1.11-sunxi. After the update the board does not boot anymore. Further investigation shows that the original "/boot" folder was looking like this: And after the upgrade, I get this: A "uInitrd" symlink is broken, the "uInitrd-6.1.11-sunxi" file is missing, and obviously, the board cannot boot. Question N1: where can I get the proper "uInitrd-6.1.11-sunxi" file? I cannot find it online,…

Hello, I have Orange Pi 3 LTS with Armbian 22.*.1 5.15.80-sunxi64. It have been working well for about a year, but after upgrading to 23.8.16.1.47-current-sunxi64 network interfaces stop working at all. I can't downgrade kernel with arbian-config because it need internet access. Here is output from armbianmonitor: armbianmonitor.txt Could you please guide me how to solve this issue?

I'm connecting my Orange PI PC 3.5mm jack to this power amp: HiLetgo 5pcs PAM8403 2x 3W Mini Digital Power Amplifier Board AMP Class D 2.5-5V Input If I connect a 5v 2a power supply to the amp and a 3a 5v power supply to the Orange PI PC, it sounds great with no noise form the Orange PI and no distortion from the amp power supply. If I try to run the amp from the 5v pins on the Orange PI PC with the 3amp 5v supply, it will work, but there is a lot of noise from the main board and the amp does not get enough power to run properly. Should 3a be enough to run both these peripherals? I think the power amp will pull about 600ma, not sure what the Orange PI…

Should it be possible to take a working SD card out of one OrangePi Zero and put it in a new one? Same board and amount of RAM and everything.

I'm on an Orange PI PC running Armbian_23.08.0-trunk_Orangepipc_bullseye_edge_6.5.1_minimal I've enabled analog audio out the 3.5mm jack using overlays=analog-codec in /boot/armbianEnv.txt I'm connecting the analog 3.5mm jack to a 3watt amp & speakers. It works mostly, but I only get audio on the left channel. Alsa mixer Line Out only allows one channel to be unmuted at a time - left channel or right channel. Left channel sounds pretty good (DAC reversed appears to increase dynamic output). Right channel is very low volume and appears to be "squelched" - is the audio signal reversed from ground or something? Anyway, is there some …

Hello there. I'm trying to set up GPIO pins PD15 and PD16 on my OrangePi 3 LTS to work as input pins using device tree overlays. The overlay I have created is the following (for PD15 only): /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h6"; fragment@0 { target = <&pio>; __overlay__ { my_pins:my_pins { pins = "PD15"; function = "gpio_in"; default-state = "on"; }; }; }; fragment@1 { target-path = "/"; __overlay__ { my@0 { compatible = "my-gpio"; pinctrl-names = "default"; pinctrl-0 = <&my_pins>; gpios = <&pio 3 15 0>; status = "okay"; }; }; }; }; Probably …

Hi guys. I installed Armbian 23.8 Bookworm on mmc and I have not eth0 interface. WiFi works. Could you help me?

I am having a network problem that I can not figure out. First I had to roll back the kernel to version 5.x to even get wifi to work. Since then I have tried all sorts of things. No matter what I do, when I unplug the eth0 the wifi goes away as well. Here is some stuff that might help. __ __ _ _ _ ____ _____ | \/ | (_) (_) |/ __ \ / ____| | \ / | __ _ _ _ __ ___ __ _ _| | | | | (___ | |\/| |/ _` | | '_ \/ __|/ _` | | | | | |\___ \ | | | | (_| | | | | \__ \ (_| | | | |__| |____) | |_| |_|\__,_|_|_| |_|___/\__,_|_|_|\____/|_____/ Version 1.1.1, based on Armbian 23.02.2 Bullseye Running on OPi 3 L…

[root@lalaki ~]# journalctl -p4 Sep 16 14:27:11 lalaki kernel: watchdog: watchdog0: watchdog did not stop! Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 0 Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 1 Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 2 Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 3 Sep 16 14:26:51 lalaki kernel: KASLR disabled due to lack of seed Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 0 Sep 16 14:26:51 lalaki kernel: axp20x-regulator axp20x-regulator: DCDC frequency o…

Hello. I have problem with SSH on Armbian 23.8 Bookworm Orange Pi 3 LTS. Orange seems like booting ok, DHCP works too, since I see Pi's IP in my router settings, also I can ping it, and I'm 100% sure its Pi's IP since I have only my PC connected to LAN. I waited for 5 mins, and still couldn't connect to SSH. I tried to do port scan on Pi's IP and nmap says that only 5555 port is open. I am using 2A Adapter, so there should be no power issues. Here are some logs. Spoiler ping 192.168.1.82 Pinging 192.168.1.82 with 32 bytes of data: Reply from 192.168.1.82: bytes=32 time=2ms TTL=64 Reply from 192.168.1.82: bytes=32 time&lt…

as per title, armbian sucks. The last version is totally broken, unusable. Only one quarter of the screen is readable, the rest is black: why nobody has said that? Why nobody says that vlc and mpv crashes every 2 min making watching a movie impossible? The once half-decent armbian is ready for the bin now

Hi, I recently purchased a Banana Pi M2 zero, and I can't seem to get the OTG port to work with any kind of operating system. I have tried all of the normal remedies like cable issues, power supply, etc. With no luck. I know Armbian is usually the best OS for these little boards, but I can't seem to get a keyboard or mouse to work with it. Although it boots up just fine. Any help would be greatly appreciated!

I just run an "sudo apt upgrade" and my 22.05 system was upgraded to 23.8.1 As a result WiFi stopped working. The wireless interface disappeared and can not be configured with armbian-config. On the positive side it seems like the load bug is now fixed, load can now be 0.0.0 at its lowest as opposed to 1.1.1 before. is there a way to revert back to the old kernel with Armbian?

The topic is no longer new, but I have not found the reason and its solution! If you turn off the power (just pull out the wire) then you can get a non-working system. As I noticed, the files opened at the time of launch are broken. And some files such as /etc/boot/armbianEnv.txt in general, they are recorded with some kind of garbage!!! Because of this, your settings fly off! For example, I use ttys1 and this option is registered armbianEnv.txt , but after the power loss, there is just terrible garbage in this file, as if the memory dump fell there!!! For example, I still use dotnet, so it also breaks down and does not start anymore!! When y…

I'm trying to get a HDMI LCD touchscreen working. The pinout is compatible with Orange PI PC except the SPI CS pin is on pin 26 (WPI 11) instead of pin 24 (WPI 10). Is there an easy way to move the SPI CS pin to another GPIO pin? Also, I'm not sure how to properly configure the pen down interrupt pin for pin 22 (WPI 6) So far, I've got the following working: Image: Orangepipc_2.0.8_debian_buster_desktop_linux5.4.65.7z Touchscreen: 3.5 Inch HD HDMI USB LCD Touch Screen 3.5" Display Module 480×320 1920x1080 for Raspberry Pi 3rd 4th Generation 4B/3B+/3B/2B orangepiEnv.txt: overlays=spi-add-cs1 spi-spidev param_spidev_spi_bus=0 para…

Hello. I decided to build an original image for my Fly Pi board. HDMI output not working. The image is shown only when loading Uboot, and then turns off and a black screen appears. Here are the logs: https://ix.io/4EWM DISPLAY=:0 xrandr output: can't open display :0 X org log: https://paste.debian.net/1290516 I'm confused and don't know what to do...

After flashing the sd card with armbian and booting it, it asks me to enter the root password, however the keyboard that is plugged in isnt detected and nothing is typed on the screen. Ive already tried bookworm and jammy, both cli and minimal-cli variants. It is not a keyboard or usb related issue, i tested it with an older version of armbian and the keyboard still works.

Hello, I bought an orange pi plus 2 and connected it to the power supply, the android that is already installed recognized the mouse and keyboard without any problem. I tried to boot the ARMbian using the version I was given, the orange pi plus 2e version, because there is no direct support for the orange pi plus 2. The BOOt works without any problem, but when I create the user, the system doesn't recognize my keyboard or mouse and I get stuck on the creating user screen. I'm using a 5V/3A power supply and a bluetooth mouse. Can anyone tell me if this is a kernel bug or am I using the wrong version to BOOT?

Hi all! Could someone help me? I am triying to setup Kedei 3.5 HDLCD touchscreen. I found a common example sunxi-DT-overlay for ads7846. /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target = <&pio>; __overlay__ { ads7846_pins: ads7846_pins { pins= "PA7"; function = "irq"; }; }; }; fragment@1 { target = <&spi0>; __overlay__ { #address-cells = <1>; #size-cells = <0>; status = "okay"; ads7846@0 { compatible = "ti,ads7846"; reg = <0>; /* Chip Select 0 */ …

Hi, I use an OrangePi Zero as a race timer for a car. It is powered from the car. So when the car starts the OrangePi gets power and boots and when the car is turned off the OrangePi loses power and "turns off". This isn't ideal but I don't have a lot of options. I feel like this is a fairly common use case for electronics in cars especially ones like race timers etc. Unless I have a battery as well. I was wondering what are the best things to do to protect against the sudden power loss so that I don't corrupt anything? Is it possible to make parts of the file system read only maybe? All I do with the OrangePi is run a C++ application, it use…

Hi there! I've recently configured the ov5640 camera overlay and was able to capture videos either with mjpg-streamer of ffmpeg. Now on 6.1.34 both causes now a kernel oops. From the stack trace it looks like it happens inside v4l2 "media_pad_remote_pad_first" Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... ... PC is at media_pad_remote_pad_first+0xa/0x58 I don't think v4l2 is the root cause because this may mean it fails alle the time which is unlikely. Looks like a null ptr gets passed in into media_pad_remote_pad_first ffmpeg used like this, but other parameters all resulting in the kernel oop…

Hello, I'm running Armbian on the original (LeMaker) A20 powered BananaPI : cat /etc/issue Armbian 21.08.6 Buster \l I did an apt-get upgrade few days back, and since, it's CPU load is always around 1.00 even if I don't run my custom application (obviously, it wasn't the case before). Nothing special in /var/logs/messages, but top show me a kernel process always on top : top - 15:03:43 up 1 day, 17:40, 1 user, load average: 0,98, 1,03, 1,12 Tasks: 112 total, 2 running, 110 sleeping, 0 stopped, 0 zombie %Cpu(s): 4,5 us, 6,3 sy, 0,0 ni, 89,0 id, 0,0 wa, 0,0 hi, 0,2 si, 0,0 st MiB Mem : 993,9 total, 583,3 free, 119,7…

Hello, The Orange Pi 3 ARMBIAN image is no longer available on ARMBIAN Website, is there any way to get it ? https://www.armbian.com/orange-pi-3/ Thanks

My OrangePi Zero is on 23.02 and I intend to stay with it (unless/until xradio wifi works on kernel 6.x). Just ran apt update and it shows these available packages: armbian-config/bullseye,bullseye 23.08.0-trunk--1-SA9048-Baeda all [upgradable from: 23.02.2] armbian-firmware/bullseye,bullseye 23.08.0-trunk--1-SA1251-B226d all [upgradable from: 23.02.2] armbian-zsh/bullseye,bullseye 23.08.0-trunk--1-SAbfee-Baf88 all [upgradable from: 23.02.2] I'm surprised to see anything related to 23.08 seeing as that version hasn't been released yet, so obviously I don't really understand what it means to be seeing this. Should I go ahead and install these ev…

Hi there! I've just compiled from armbian buil tools a new image for Orange Pi 3 LTS. Then flash it on sdcard, anything was well, but armbian doesn't start at all. Nothing on the HDMI, nothing on the debug serial. Also LED doesn't light. I've tried two images: ubuntu jammy with GNOME and next case XFCE. Both cases didn't work. I've downloaded prebuilt image from armbian.org and it starts well. In my opinion, some problem with custom images in u-boot. but I don't know how to give a diagnosis.

So I am using Armbian on Linux with Orange Pi 5 and as I connect my Ethernet cable it is not able to connect as if i got to Firefox a tab will not be able to load. Any suggestions.

Under kernel 4.9, using a usb3.0 to Gigabit interface with RTL8153b card, the upstream and downstream speed can reach Gigabit. But with kernel5.10, the speed can't reach gigabit, and the driver file has been changed to the latest version, but still no effect. kernel5.10 Speed measurement root@orangepi3-lts:~# iperf3 -c 192.168.3.201 Connecting to host 192.168.3.201, port 5201 [ 5] local 192.168.3.146 port 44376 connected to 192.168.3.201 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 24.8 MBytes 208 Mbits/sec 0 147 KBytes [ 5] 1.00-2.00 sec 23.5 MBytes 198 Mbits/sec 0 147 KBytes [ 5] 2.00-3.00 sec 23.5 MBytes 197 Mbit…

Hi there, I have OPi3 (not B nor LTS), now I got an SSD module ( https://allegro.pl/oferta/dysk-ssd-128gb-msata-6gb-s-13044566959 ), and it does not seem to work (nothing related in lsblk). I am using Armbian 21.02.3). Any ideas? the red LED is on, mechanically looks compatible with socket do I need something to enable this? armbianmonitor -u : http://ix.io/4Bkf

I just installed the image located here and am unable to get a bluetooth keyboard and mouse to connect. https://www.armbian.com/orange-pi-zero-plus-2-h3/ And used armbian-config -> Network -> Enable bluetooth. Here's the output of some common debugging commands I found in the forums. root@orangepizeroplus2-h3:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0001 Linux Foundation…

has anyone ordered and/or played with this https://www.cnx-software.com/2023/07/03/orange-pi-zero-3-allwinner-h618-sbc-ships-with-up-to-4gb-ram/ https://liliputing.com/orange-pi-zero-3-is-a-cheap-tiny-single-board-pc-with-up-to-4gb-ram-gigabit-ethernet-and-allwinner-h618/ http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-Zero-3.html even the linux images is very 'fresh' as in that they are just released *yesterday* 😄

With Armbian 22 (kernel 5.15 and bullseye/jammy) the Orange PI 3 LTS worked great including WiFi, ETH, Bluetooth. Partly thanks to @Ukhellfire and @going. Downloadable here: https://xogium.performanceservers.nl/archive/orangepi3-lts/archive/ Below is what I find the status is for the new Armbian 23 images provided for here : https://www.armbian.com/orangepi3-lts/ Branch current: Main downloads Armbian 23 with kernel 6.1 bookworm: It boots, but every 3rd or 4th keystroke is ignored. No ETH, no WiFi. Armbian 23 with kernel 6.1 jammy: It boots, keystrokes are OK, ETH is OK, but WiFi doesn't work. Branch edge: Rolling release…

Basically, just did 3 consecutive runs of iperf3, and they look like this. And it is not cpufreq, since setting it to performance on all CPU cores does not affect things. Using the current stable Debian image with kernel 6.1.30. Any ideas? $ iperf3 -c 192.168.103.156 Connecting to host 192.168.103.156, port 5201 [ 4] local 192.168.0.101 port 58758 connected to 192.168.103.156 port 5201 [ ID] Interval Transfer Bandwidth Retr Cwnd [ 4] 0.00-1.00 sec 27.3 MBytes 229 Mbits/sec 0 201 KBytes [ 4] 1.00-2.00 sec 26.4 MBytes 222 Mbits/sec 0 195 KBytes [ 4] 2.00-3.00 sec 26.3 MBytes 221 Mbits/sec …

Hello everyone! Yesterday I downloaded "Armbian 23.5 Jammy". Unfortunately the integrated wifi module does not work. I tried several alternatives but with the same problem. I am not an expert on the subject. Any solution? I'm trying to compile and in one of the steps it tells me that the "Orange Pi 3 LTS - H6" is no longer supported. If anyone knows and can help would be appreciated. https://paste.armbian.com/varepekose Original: Hola a todos! En el dia de ayer descargue "Armbian 23.5 Jammy". Lamentablemente no funciona el modulo wifi integrado. Probe con varias alternativas pero con el mismo problema. …

For a long time, for more than three years, I did not use my BananapiPro board. And recently I decided to launch it again.I downloaded new Armbian image distribution. But the system when loading gives out an error. After the initialization of the devices, a message appears: Device 0: unknown device ethernet@1c50000 Waiting for PHY auto negotiation to complete......... done Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.2.200 (5ms) *** Warning: no boot file name: using 'COA802c8.img' Using ethernet@1c50000 device TFTP from server 192.168.2.1; our IP address is 192.169.2.200 Filename 'COA802C8.img'. Load address: 0x42000000 Loading: T T T …

Hello, I try to enable audio linein, controls with alsamixer are the following. Is it possible to redirect audio input to output directly or with audio equalizer ? I actually have sound with a speaker test, but I can't listen to the audio line-inActually I have sound with speaker test, but I can't listen audio linein Best regards

Hi all I have a project need high uart baudrate, > 2Mbit/S, how can I get this work, seems the stty not work correctly

I switched mentioned pins to IN mode. And it is seems they are pulled up by default. +-----+-----+----------+------+---+-Orange Pi+---+---+------+---------+-----+--+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+----------+------+---+----++----+---+------+----------+-----+-----+ | | | 3.3v | | | 1 || 2 | | | 5v | | | | 12 | 8 | SDA.0 | IN | 1 | 3 || 4 | | | 5V | | | | 11 | 9 | SCL.0 | IN | 1 | 5 || 6 | | | 0v | | | If physically connect that pins to the ground it shows 0 level. But I need it 0 by default. A…

Hello, I am a beginner on NanoPi. I had a NanoPi neo 512M, and I am searching for a campatible image for it. unfortunately, I didn't find my device in the list but I found NanoPi Neo 2 instead. I believe that its image is not compatible with my device so, can anyone give some hands to have a compatible image? thanks in advance

Image Armbian_23.5.2_Nanopiduo2_bookworm_current_6.1.30.img uname -a Linux nanopiduo2 6.1.30-sunxi #1 SMP Wed May 24 16:32:53 UTC 2023 armv7l GNU/Linux It turns out the dtb has some missing pieces: ethernet@1c30000 { compatible = "allwinner,sun8i-h3-emac"; syscon = <0x1e>; reg = <0x1c30000 0x10000>; interrupts = <0x00 0x52 0x04>; interrupt-names = "macirq"; resets = <0x03 0x0c>; reset-names = "stmmaceth"; clocks …

I've change OpiZero's cpu from H2+ to H5, and made linux5.4.65 image with the option of "Orangepiplus (H5)" of the Build-Package which described in the Orangepi manual. After the linux startup, the output of command DMESG shows "sunxi-mmc 1c10000.mmc: Cannot do DMA to address 0x00008000514a3870", and TRACE as follows: [ 212.402793] xradio_wlan: version magic '5.15.27-station SMP preempt mod_unload aarch64' should be '5.4.65-sunxi64 SMP mod_unload aarch64' [ 248.019893] xradio_wlan: loading out-of-tree module taints kernel. [ 248.024327] xradio_wlan: module verification failed: signature and/or required key missing - tainting kernel [ 248.027…

Initially I attempted upgrading the kernel from 6.1.26 to 6.1.33 using the build scripts to generate the newer kernel and headers. After rebooting I found that the system just appeared to hang around starting kernel. I did wait 10 minutes at first, thinking that perhaps their maybe some stuff going on in the background but after that conclude that it had most certainly crashed. The frustrating thing being that I did not appear to get any errors come through the debug port. At this point I assumed that perhaps something may have broke during the upgrade. My second attempt was using a completely fresh compiled image but unfortunately the result was still the same. …

Hello, I'm working on a project which include a microcontroller and a NanoPi NEO Core running Armbian FriendlyCore distribution. The NanoPi is wired to the µcontroler ICSP which can reset the µcontroller for update purpose. The allwinner H3 datasheet state that the GPIOA6 (the one linked to ICSP) should start with HIGH-Z and no resistance pulling, it seems to do so but a few second after reboot it seems to go low as all other GPIO... resulting in an unwanting reset of the µcontroller. Is there a way to change this by setting the default state somewhere in the system, or should I have to use dts files or core compilation ? Any solution would be appreciated. …

Hi all, I'm new here and somewhat new to "modern Linux"..I'm more a BSD Guy... I'm using, administering and programming on unices since approx 1992, using FreeBSD (mostly) at home, my wife has a Laptop using Mint installed by me, but I haven't put much effort into my Linux experiences since systemd came up... Ok, approx 2 years before I've got a bunch of more or less unusual embedded HW..Beaglebone, Olinuxino with an A10, some Intel based thingy and something from AnalogDevices if I remember correctly. All of them are more or less old. Now I want to build a kind of a home automation appliance that is reading out data f…

Hello, I'm trying the currently offered Armbian Bookworm images for the Orange Pi Prime, using kernels 6.1.30 and 6.2.16, and notice that there is no support for SoC temperature monitoring, neither in armbianmonitor, nor in /sys/devices/virtual/thermal/. Here is the debug info from 6.2.16: https://paste.armbian.com/cetovulubu Is that a known issue? An older Armbian image that I have downloaded previously, using the kernel 5.15.93, shows the temperature just fine.

i have orange pi pc plus and i use a hdmi monitor with it, i use xorg to run browser kiosk there is a problem with monitor if i connect hdmi before armbian starts monitor works well and show desktop but if i start orange pi (wait few seconds) and then connect hdmi cable then the monitor shows nothing

Hi, i've a tablet that has an Allwinner A20 socs. Can i install armbian? Which are installation steps? Thank You Luigi

I'm missing something essential. I have NanoPi Neo v1.4 with Armbian 23.5 Jammy CLI (Linux nanopineo 6.1.30-sunxi). My display is Nokia5110 LCD or PCD8544 With spi-spidev DT I can successfully via `spidev0.0` with `spi-tools`. I.e. I confirm that spi is working. Now, I studied about DTO and fbtft driver, found that it supports pcd8544. I wrote this kind of DTO and added it to `armbianEnv.txt` /* * Device: LCD5110 (nokia5110) 1.6"(84x48px) SPI display Module PCD8544 * Module Connector * SDI(MOSI) <- PC0 * SCK <- PC2 * CS <- PC3 * RESET <- PA1 * DC/RS <- PA3 * LED <- PA2 */ /dts-v1/; /plugin/; / { compatible = "all…

Hi, I am working on enabling crust support in Armbian. A draft version of pull request is here. I have made the changes for the same. With my changes, crust compiles as part of building the image and gets bundled in u-boot. I can also see the following message from U-boot U-Boot 2022.10-armbian (Jun 14 2023 - 13:49:59 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: FriendlyARM NanoPi NEO DRAM: 512 MiB Core: 61 devices, 18 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: serial Starting SCP... Net:…

Hi, my Armbian Reports as 23.02.2 with Kernel 5.15.93. According to website there is already 23.5 with Kernel 6.x. How can I upgrade my existing installation? I tried apt update dist-upgrade and the "Update all packages and firmware" option in armbian-config. best regards thommy

Bookworm 6.1.30 - wi-fi don't work.

Armbian Jammy (Minimal CLI) boots/works fine from an SD Card. (Armbian_23.5.2_Nanopi-r1_jammy_current_6.1.30_minimal.img.xz) apt update && apt upgrade -y && apt autoremove apt install armbian-config -y armbian-install I choose option #2 - Boot from eMMC - System on eMMC Accept the warning. I choose option #1 - ext4 The install appears to move along smoothly. I choose the "Power Off" option. Pull the power, remove the SD Card. Reconnect the power. I never see the "heartbeat" on the "System"(red) LED. The NanoPi never boot or obtains an IP address.

Hello I need to connect my modem Huawei E3372-325 to my NanoPI but when i write command ls usb get it root@PC_42:~# lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 3566:2001 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub…

Hi, I need a help. I have waveshare 4inc lcd touch play display but I don’t know how to enable touch play. Please Help me.

Thought this might be useful: FROM: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=2236 01 3.3V 02 5V 03 TWI0-SDA PA12 04 5V 05 TWI0-SCK PA11 06 GND 07 PWM1 PA06 08 UART1_TX PG06 09 GND 10 UART1_RX PG07 11 UART2_RX PA01 12 SIM_CLK/PA_EINT7 PA07 13 UART2_TX PA00 14 GND 15 UART2_CTS PA03 16 TWI1-SDA PA19 17 3.3V 18 TWI1-SCK PA18 19 SPI1_MOSI PA15 …

Hello all, I'm trying to revive my old OPIZ + cheap expansion board. I've tried all recent images available but I couldn't get it to work. Is there any old version (with repository still alive) available with which I can install sox + alsa. I don't need recent kernel or software (but wifi) Any idea? Thanks for help Pascal

I use Armbian_23.5.1_Orangepi3-lts_bookworm_current_6.1.30. I'm trying to download in armbian-config kernel headers, but linux-headers-5.15.93-sunxi64 are downloaded. How to download kernel headers 6.1.30.?

http://paste.armbian.com/icedujiguw.yaml Hello everyone, trying to give new life to this old Orange Pi+ 2. Here is described what hapens when i try to boot up latest image. Can anyone help. Thanks in advance. Armbian 23.8 Bookworm Kernel 6.2.y, Size: 421Mb, Release date: Jun 3, 2023 SBC gets stuck after the request Sense .. and doesnt booy up, if i plug a device in usb ports, it bootloops .. see below using same sd-card and a diffrent image file works with no issues . hardware : grounded out pin 9 of the SD card slot (checked with multimeter and works) U-Boot SPL 2022.07-armbian (Jun 03 2023 - 19:37:25 +0…

Attention, whatever you do next is at your own risk! Fixed dts overlay file for Armbian 23.02.2 (attached). 1. Now the system can fall asleep and wake up by a timer (without an external RTC, provided that it is powered) or by pressing a button - while wifi connects itself (if there is an automatic connection) and the system continues to work as if nothing had happened without unnecessary loading. 2. As a bonus, I added an indication of reading from a flash card as a red LED (this can be turned off). 3. I also activated the host on the micro-usb connector - now you can connect something else via the otg adapter as a third USB connector. To apply t…

How to install Home Assistant Supervised on Armbian 23.02 Jammy (plus minus, but quite installed on the previous release of Armbian, this is based on Debian 10) Performed exclusively without a graphical interface, from the console. Works stably on Orange Pi Lite , including a connected Bluetooth dongle via USB and sensors to it. 1. The first installation of Armbian and the subsequent creation of a user and passwords, the next is required to install all updates via sudo apt update && sudo apt upgrade -y . Then you need to install the Firmware update through the armbian-config ->System utility as in the screenshot. Скрытый текст …

Tried both Debian and Ubuntu based 23.5 releases on my v1.4 board Boot process stops at "Starting kernel..." Also tried the "minimal CLI" debian release with same results. The previous versions 23.02 are fine. ▒ U-Boot SPL 2022.07-armbian (May 27 2023 - 19:26:49 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.07-armbian (May 27 2023 - 19:26:49 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 512 MiB Core: 65 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c10000: 1 Loading Environment from FAT... Unable to use mmc 0:1.…

Hi! I am trying to use Armbian 23.5 Jammy XFCE for new Orange Pi Zero Plus 2. I have TTL-USB connection through Serial port. In pyutty window i see log U-Boot SPL 2022.07-armbian (May 27 2023 - 19:28:04 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.07-armbian (May 27 2023 - 19:28:04 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero Plus 2 DRAM: 512 MiB Core: 65 devices, 18 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: serial Net: …

The problem seems to be kernel version 6.1.30; Just writing image file 'Armbian_23.5.1_Nanopineo_bookworm_current_6.1.30_minimal.img' to SD-card gives the following output via serial console: U-Boot SPL 2022.04-armbian (May 27 2023 - 19:27:28 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.04-armbian (May 27 2023 - 19:27:28 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: FriendlyARM NanoPi NEO DRAM: 512 MiB Core: 33 devices, 12 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: seria…

Hi! I have banana pro, 5.15.93-sunxi #23.02.2 (bullseye), and use internal wifi adapter as a wifi client. The medium btw my client and ap is instable, there are frequent rate changes (6Mbps...54Mbps), so in order to get rid of it I need to set mandatory wifi rate no more than 6 Mbps. Give me the hint, please: 1. To set wifi rate strictly to 6 Mbps. I had tried iwconfig wlan0 rate 6M - I got "Error for wireless request "Set Bit Rate" (8B20) : SET failed on device wlan0 ; Operation not supported." . 2. To adjust 802.11n parameters (rate, number of spatial streams and so on). Thank you in advance, Aleksei

Hello everyone, I encountered an issue while using SPI with my Orange Pi 3 LTS, and now I'm going to share some solutions. Perhaps the Armbian Team can assist me in resolving the final problem. These tests were conducted on Armbian 23.02.2 Bullseye with Linux 5.15.93-sunxi64. The initial step I took to ensure the appearance of `spidev` on the Orange Pi 3 LTS was to include these configurations in `/boot/armbianEnv.txt`. overlays=spi-spidev1 param_spidev_spi_bus=0 param_spidev_spi_cs=0 Note: If `spi-spidev` and `spi-spidev1` are added together, it will not work, and the `spidev` will not appear when using the `ls /dev/sp*` command. …

I've tried many permutations of overlays and user-overlays and I can get /dev/spidev0.0 or /dev/spidev0.1 to be present, but I can't seem to get both simultaneously. I need both to migrate a project from an older Fedora distribution relying on modprobe to the latest version of Armbian. Any suggestions will be greatly appreciated! I started with very recent Armbian 23.02 Bullseye XFCE downloaded from arbian.com/banana-pi-plus .. Armbian_23.02.2_Bananapi_bullseye_current_5.15.93_xfce_desktop.img and I added the following to the /boot/armbianEnv.txt file, as described in the Armbian page associated with the BananaPi M1+ .. f…

At Raspberry Pi (at least on R.Pi 4) it is possibility to set up more than one 1-wire bus. Can that be done on Orange Pi plus 2e with Armbian? uname -a Linux XXXXXXXXXXX 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l armv7l armv7l GNU/Linux /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=d908a8da-8d2e-4802-8a05-aaab4f3290bb rootfstype=ext4 overlays=w1-gpio param_w1_pin=PD14 param_w1_pin_int_pullup=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u If it is possible: Any tip on configuration will make me happy. And can it be internal pu…

I'm using Armbian 23.02 Bullseye CLI. I didn't want the HDMI to show the boot system log and TTY1 login screen. According to the armbian documentation, I changed "console=both" to "console=serial" in /boot/armbianEnv.txt. I checked /boot/boot.cmd related to console, and I confirmed that this modification is OK, but it cannot start, uboot printed "Starting kernel..." After that, there is no output, and the power supply is only 5V 170mA. The following is the printing of the serial port. If anyone has been in a similar situation, please give me a little help, thank you very much. U-Boot SPL 2022.07-armbian (Feb 17 2023 - 22:32:08 +0000) DRAM: 2048 MiB Trying …

Hello! Brand new user here to the NanoPi Neo and even the forum. I'm planning to use a NanoPi Neo as hardware "interactor", the main idea is to connect a NanoPi Neo to a smartphone (Android or iOS), power the board from the USB cable and work in Host Mode to interact with de smartphone with libimobiledevice or adb. OTG does not support charging + data at the same time without a "special" OTG adapter. What I want to do is power the NanoPi by using the smartphone and even interact with it in host mode, like a regular computer will do, in simple terms, using a single cable, but getting power from it. Is this possible using NanoPi microUSB+OT…

ARMBIAN 5.41 user-built Debian GNU/Linux 9 (stretch) 4.14.34-sunxi, Orange Pi Zero board. Very limited Debian installed, wifi doesn't work. I found lines install xradio_wlan /bin/false install 8189es /bin/false in /etc/modprobe.d/blacklist.conf and removed it. In /etc/modules-load.d/modules.conf I added the lines 8189es xradio_wlan. No help, wi-fi didn't work, nothing about xradio or wifi in dmesg. I figured out that there was no drivers (modules) for wifi. Found this article https://linux-sunxi.org/Wifi I execute the commands from the article, section RTL8189ES / RTL8189ETV The driver has its own repository: git clone https://github.com/jwrdegoede/rtl8189ES_li…

Hi gang. I am having a consistent problem changing the board over boot from the SD with the system on any kind of USB attached drive. The drive I want to put it on is a 1t ssb, which otherwise formats fine, over and over again, burns images on it fine (though rpi doesn't like how much power it grabs). But I duplicated the problem with a formatted SD card in a reader in the USB port as well. The same error message appeared. Now I have to say that I have read this post here: to see if there was anything unique to the H3 to accomplish this, but Igor said there to just follow the simple directions at Getting Started, which though dated, still work close…

Is there any way to get interrupts working on BPI M2 Berry/Ultra? I tried with raspbian and wiringPI/RPi.GPIO but there is a wait for support() “bug” which has been reported a while ago but no updates have been made in the thread. Currently Im running Armbian 22.11.00. If anyone has some experience or suggestion for a library/smth and is willing to share it that would be great. Thank you for your time.

Hello, I am trying to communicate using UART PORT. I have connected to 8, 10 and GND pin. Also I enabled UART3, but it doesn't work. Any solution? Thanks !! Enviado desde mi iPhone utilizando Tapatalk

Hi, Is it possible to remap the i2c1 to use the i2c0 default pins via armbianEnv,txt ?. What I want to achieve is to have the PD25 and PD26 to appear as bus 1. Thank you.

Hi, When I scan the I2C with i2cdetect, I get the following, without connecting any i2c device. May I know which device on the motherboard is taking up the three addresses. Thank you sudo i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: 30 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: 50 -- -- -- 54 -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -…

I did try the latest Armbian 23.5 Bookworm on my banana pi m2 zero with allwinner h3 chip and I couldn't get the USB OTG port working (i. e. no keyboard recognition) and eth0 also did not work. After a lot of searching I found an old image (BananaPi-M2zero_Armbian_2021.08.1_bullseye_CLI_5.10.60.img) which did work. I wonder what happened to the kernel Kernel 6.2.y edition and why those crucial hardware features are not working anymore. Is there a vault somewhere of older armbian software revisions?

I've been trying to bring up Armbian on my Banana Pi M2 Ultra (with A40i SoC). First I tried using the community rolling release, and then building it myself from source code. In every case, it was failing to boot; on the HDMI console it was hanging at the stage where the initrd was attempting to scan for the root partition. ("Scanning for btrfs filesystems") Taking a closer look at the verbose output of the UART console during a boot attempt, I saw that there was an error message about the sunxi-mmc device driver experiencing a failure while it was enumerating the EMMC chip: [ 4.136553] mmcblk2: mmc2:0001 8GTF4R 7.28 GiB [ 4.144362] sunxi…

Hello everyone, Would like to ask for some guidance regarding how to install armbian on a t507 processor. as written here in this post allwinner 507 processor it says For this reason I have tried to burn an image for orangepi zero 2 but it doesn't boot, it just get frozen and I can't get any logs because the serial console do not prints anything all black. Does someone could maybe have some suggestion of what I could try? anything is more than welcome. Thank you in advance

Hi all, I try to use SPI on the BananaPi M2 Berry. The devices are activated in the configfile and the devices spidev0,0 and spidev1.0 are shown in the /dev .directory but the spi-bus did not work. DMESG shows the following error - messages : [ 0.944871] sun6i-spi 1c05000.spi: Failed to request TX DMA channel [ 0.944893] sun6i-spi 1c05000.spi: Failed to request RX DMA channel [ 0.945987] sun6i-spi 1c06000.spi: Failed to request TX DMA channel [ 0.946006] sun6i-spi 1c06000.spi: Failed to request RX DMA channel OS version is 6.2.12-sunxi Any idea what's wrong ?

Pinecube fails to boot with Armbian_23.5.0-trunk.140_Pinecube_bookworm_edge_6.2.13.img . In the boot log is this line: So I tried to modify `fdt_addr_r` env variable and were able to succesfully boot with theese commands executed in u-boot console: So adding following line to /boot/armbianEnv.txt on sdcard can fix booting permanently: Complete boot log:

Currently I receive rustc crashes after memory usage get to 3GB (1GB RAM + 2GB SWAP) when building firefox. After looking around why, I found that kernel isn't build with lpae extension. Although H3 soc supports lpae (Large Physical Address Extension), but kernel has CONFIG_ARM_LPAE flag not set and so we can't use more than 3GB of memory (1GB is reserved for kernel). (Processors that implement the ARMv7-A Large Physical Address Extension (LPAE), expand the range of accessible physical addresses from 4GB (232 bytes) to 1024GB (240 bytes) a terabyte, by translating 32-bit virtual memory addresses into 40-bit physical memory addresses.) After looking a…

Hello, long time Banana Pi user here. I have a BPI-M2+ and recently decided to write Armbian_23.02.2_Bananapim2plus_bullseye_current_5.15.93_minimal.img to emmc. I am using cat6 over gigabit LAN and am seeing scp and rsync transfers to the device averaging 1.7mb/s. Transfering an 850mb file took unusually several minutes. It starts off at 40mb/s then quickly drops to under 2mb/s. Is this typical? I would think over LAN I would be seeing much faster speeds. Untarring this same 850mb archive also took unusually long. Could the emmc be damaged or on it's way out? How would I check? Please see armbianmonitor output. https://pastebin.com/RCa…

Neo has one SPI port and I need two, so would like to add another spi using spi-gpio, but no success (I think). I am using Armbian 23.02.2 Bullseye, default kernel does not enable it, recompiled using linux-source-5.15.93-sunxi.tar.xz, enabled spi-gpio as module. Digged around forum, prepared below dts and armbian-add-overlay succeeded. But there is no message arrived when loading (dmesg shows nothing about spi) and no /dev/spi* created. Is it OK or there must be something? Please advise.... / { compatible = "allwinner,sun8i-h3"; fragment@0 { target-path = "/"; __overlay__ { …

I configured Armbian on a mSD card and decided to try and move it to the eMMC. I used the nand-sata-install utility, All files from the mSD card are copied, and the last step fails. I get Error: no u-boot package found, exiting Any pointers?

i am normal write the sd card by rufus, can boot into system, when i use armbian-config install system in emmc boot in emmc after copy i try shut down and remove the sd-card, boot fail, power led no on, how to fix, thanks

Just tried Armbian 23.5 Bookworm, cli & minimal. Both report the same in the console. Board works just fine with official img from www.friendlyelec.com Here is the terminal output.

Hello, I have installed the latest version of armbian on my Orange pi win and I have not been able to make the desktop appear, it always stays waiting for a command, I have done update and upgrade and nothing. Can somebody help me

Hi. I want to install RTL8188fu on this orange pi pc but I have no luck. Bus 003 Device 005: ID 0bda:f179 Realtek Semiconductor Corp. RTL8188FTV 802.11b/g/n 1T1R 2.4G WLAN Adapter I'm using this repository https://github.com/kelebek333/rtl8188fu , but....: orangepipc:~:# sudo dkms install ./rtl8188fu Creating symlink /var/lib/dkms/rtl8188fu/1.0/source -> /usr/src/rtl8188fu-1.0 Error! Your kernel headers for kernel 5.15.93-sunxi cannot be found. Please install the linux-headers-5.15.93-sunxi package or use the --kernelsourcedir option to tell DKMS where it's located. sudo apt install linux-headers-$(uname -r) Reading package lists…

i have a tablet on Allwinner A20, I burned Armbian_23.5.0-trunk.134_Lime2_bookworm_edge_6.2.12_xfce_desktop.img.xz into sdcard, it looks like everything is okay, but the tablet work only via HDMI, how to enable the tablet display ?

Can anyone provide any information on getting the GPU driver working with a Banana Pi M2 Zero? It supposedly has a Mali 400 GPU. In my tests, it seems I am stuck with Mesa software rendering with OpenGL. When I write a program that creates an OpenGL 2.0 ES context, the vendor and renderer both list Mesa and performance is terrible (2-10 fps and GLSL shaders are incorrect) when rendering even the simplest scenes. I am using DRM (Direct Rendering Manager) with boots straight to a CLI and no desktop environment if that makes any difference. With the same code and same conditions on a Raspberry Pi Zero 2 W, OpenGL works perfectly in my tests. I am usin…

The 1-bay NAS kit v1.2 has an RTC with option to add CR2032 button cell to keep HW time when system is shut down. But running `timedatectl` when device is booted in offline mode shows RTC is set to 1970-01-01 00:00:00 which defeats the purpose of having the option of CR2032. And yes, the button cell have juice; I've bought it a week ago and tested it before putting it in the kit.

The system displays two WLANs, but in reality, there is only one onboard wireless network card. The network connection is slow and disconnected. The official system of Orangepi is normal, this issue occur in the new version of the Armbian system. logs：https://paste.armbian.com/eborebaviq

I'm a newbie. Got the NanoPi R1 that sports a UART but no Video Output. Now when I want to read the output of the serial console I need a 3-wire cable and a converter, that much I know. But what is the baud rate? Where is this configured on the armbian NanoPiR1 image (on my raspberry Pi I just checked and found the file /boot/cmdline.txt with that settings, in my case it's 115200) Why is the baud rate nowhere documented? On the download page https://www.armbian.com/nanopi-r1/ it is stated that "serial console is enabled on UART1, which is exposed on chasis" , but no hint about which speed to use. There neither is any info about the baud rate on…

I can't set up gpio-poweroff feature described here. I tried made overlays from here and here - no effect. U-boot boots with no errors. Then i am tried to edit DT (armbian-config > System > Dtc), - manually add node at pinctrl@1c20800: Скрытый текст pwr_off_pins: pwr_off_pins { pins = "PA21"; function = "gpio_out"; }; and node at "/": Скрытый текст gpio-poweroff { compatible = "gpio-poweroff"; pinctrl-names = "default"; pinctrl-0 = <&pwr_off_pins>; gpios = <&pio 0 21 0>; }; …

raw_gadget compile failed make make -C /lib/modules/5.15.93-sunxi/build M=/root/raw-gadget-master/raw_gadget SUBDIRS=/root/raw-gadget-master/raw_gadget modules make[1]: Entering directory '/usr/src/linux-headers-5.15.93-sunxi' MODPOST /root/raw-gadget-master/raw_gadget/Module.symvers make[3]: *** No rule to make target '/root/raw-gadget-master/raw_gadget/raw_gadget.mod.o', needed by '/root/raw-gadget-master/raw_gadget/raw_gadget.ko'. Stop. make[2]: *** [scripts/Makefile.modpost:139: __modpost] Error 2 make[1]: *** [Makefile:1820: modules] Error 2 make[1]: Leaving directory '/usr/src/linux-headers-5.15.93-sunxi' I cat Module.sysmvers in /usr/src/linu…

Hi. Please help me to understand how hardware encoding works in nanopi with H3 chipset. I have newest version of armbianos: cedrus and related modules is loaded by kernel There are following hardware acceleration methods and encoders Please explain me what i am doing wrong here : and here: Thanks a lot.

Hi all! After upgrading to 6.1.24-sunxi64 on my Orange Pi 3 LTS I lost sound at the audio output. dmesg shows this: platform sound_ac200: deferred probe pending I am a newbie to linux - can you, please, provide me a hint how to install the sound card back or revert to the older kernel with a working sound? Thank you!

Good morning, I'm trying to activate PWM by hardware to use wiringpi. I activate the PWM option from Armbian config hardware, but it doesn't seem to have any effect, and UART0 doesn't seem to be deactivated. I'm not sure if there's any issue or if I'm doing something else wrong. The build is Armbian 22.11.1 Jammy with Linux 5.15.80-sunxi. Thanks for the help!