Rockchip

I was getting kernel panics and discovered that my 32 GB Rock 5B Blue Edition just crashes when I try to malloc 8-9 gigabtes of memory. Is there a way to specify that this board has 32 GB ram? 5.10 works fine.

Hello everyone, Hello everyone, I have installed Armbian Bookworm 23.11.1 (kernel 5.10.110). The fan control does not work. The fan only runs at level 1. None of the many patches I tried worked. The last one tried was this: https://forum.radxa.com/t/guide-on-how-to-customize-you-pwm-fan-curve/17442 I can adjust the fan manually, but the automatic doesn't work. The "policy" file (/sys/class/thermal/thermal_zone0/policy) cannot be permanently changed to "step wise" (logged in as root). After restarting it is back to "user_space"... The access rights are: -rw-r--r--1 root root 4096 Feb 11 02:42 policy …

Since I am interested in the connection ability, I figured the info we gather should go into ONE thread. I have tried to build new kernels, but can only see USB controllers and devices two ports. I have seen a lot of work by Sebasitian Reichel @ Collabora, and his patches, but these do not seem to have the desired result on my test board. Orange PI 5. There seems to be an issue with the port mux, FUSB302, that either connects the last USB to the "vertical" port or to the "USB C" connector. I will comment my findings and attempts to correct this in this thread, and think we could find out where we are if you add your findings, successes…

Hi Gents, I would like to ask for your help or tips and tricks in the following problem... Basically to keep the long story short, I have a custom board with RK3566 and 2 GB of RAM, 32 GB Samsung emmc on it ... basically if you are familliar it is a Linxdot Helium miner which has some problems with the onboard Lora module. I had tried to flash using RKDevTool a few Debian version that I found for Rk3566 but not all of them worked properly. All the time I was able to reflash it by using RKDevTool by pressing the button while I powered up the board but after flashing the Armbian minnimal for Orange Pi3B I can't use the RKDevTool anymore, it is simply n…

I can't activate the orange pi 3b uarts Armbian Community_24.2.0-trunk.540_Orangepi3b_jammy_legacy_5.10.160_gnome_desktop, I did it this way armbianEnv.txt overlays=uart3-m0 uart7-m2 uart9-m2 overlays=uart3 uart7 uart9

Hello everyone, I have installed Armbian Bookworm 23.11.1 (kernel 5.10.110). The fan control does not work. The fan only runs at level 1. None of the many patches I tried worked. The last one tried was this: https://forum.radxa.com/t/guide-on-how-to-customize-you-pwm-fan-curve/17442 I can adjust the fan manually, but the automatic doesn't work. The "policy" file (/sys/class/thermal/thermal_zone0/policy) cannot be permanently changed to "step wise" (logged in as root). After restarting it is back to "user_space"... The access rights are: -rw-r--r--1 root root 4096 Feb 1102:42 policy Owner: = Root Root…

Hi there, I'm setting up microk8s cluster on: 2 x RockPi 4A (Linux 6.1.63-current-rockchip64) 2 x Rock 5 B (Linux 5.10.160-legacy-rk35xx) Installing microk8s and connecting cluster went without issue. My next step was to install https://microk8s.io/docs/addon-mayastor in order to create distributed volume between my nodes. The problem is that mayastor require linux-modules-extra which is not build for my kernel versions. I tried few different kernels but this module is not present there as well. My question is: Is there something what I can do? Is it possible to build this module for 6.1.63-current-r…

Hi Does anyone have a working U-boot or CLI image with serial console disabled for Rock Pi 4b or Rock 4SE? Been struggling for a week to build my own with ./compile.sh and user patch but no success, U-boot hangs at user input prompt because gps sends data from power on. Have tried all suggestions on the forum.

I tried the latest 6.8 kernel edge on my Rock 5A and noticed the CSI camera interface doesnt exist. Is there any plan or time schedule to fix that? I saw it's marked "TODO" on https://gitlab.collabora.com/hardware-enablement/rockchip-3588/notes-for-rockchip-3588/-/blob/main/mainline-status.md . So in 6.9 perhaps? (A LOT of other stuff works remarkably well though, great work!)

When I boot any variant with kernel 6..x.x from SD there is no problem with hdmi. When I flash the same variant to the nvme, it boots fine but there is no hdmi output. The orange pi logo appears for a second, then nothing. I can ssh in and everthing works fine. Any variant with 5.x.x kernel works fine from the nvme, with hdmi output. What I don't understand is that if I have output to hdmi when booting from sd, why not from nvme. What I think is relevent entries in the boot log is below. mmu fe043e00.iommu: Enable stall request timed out, status: 0x00030b Jan 30 09:38:22 orangepi3b kernel: rk_iommu fe043e00.iommu: Enable stall reques…

I'm new to SBC and tinkering with Rock 4C+ (plus) board and appreciate some support and guidance for blueooth setup. Installed Armbian 23.11.1 Bookworm CLI build. Enabled BT package from Armbian config utility as well tried installing bluez package from CLI using apt command afterwards. Started bluetooth service but seems not working. Command sequence I used: sudo apt install bluez sudo service bluetooth start sudo service bluetooth status (output says Loaded & Active). 'hcitool scan' command however returns message "Device is not available: No such device". When I installed Radxa's official Debian 11 des…

Hi all, I've just booted my NanoPi M4 V2 after not using it for a year or so and when I log in via ssh I'm told the / usage is at 100% - I've deleted all logs and the usual suspects but to no avail uname gives Linux M4V203 5.10.63-rockchip64 #21.08.2 SMP PREEMPT Wed Sep 8 10:57:23 UTC 2021 aarch64 aarch64 aarch64 GNU/Linux I'm using a 32gb SD card df -h gives Filesystem Size Used Avail Use% Mounted on udev 1.9G 0 1.9G 0% /dev tmpfs 387M 41M 346M 11% /run /dev/mmcblk1p1 29G 29G 0 100% / tmpfs 1.9G 0 1.9G 0% /dev/shm tmpfs 5.0M 4.0K 5.0M 1% /run/lock tmpfs …

Hello! I'm able to reproducibly get a kernel oops whenever I start a docker container on my Helios64 The SD card I was running my Helios64 from died and so I reinstalled Armbian using the steps to install bookworm from this post. I did skip the steps related to hs400 and L2 cache as I'm currently running the system from an SD card. After the install seemed to be working well I installed zfs, imported my existing pool, and then installed docker. My previous setup was using docker's ZFS storage driver so I got that configured as well. Now, whenever I start up a docker container (ie by running "sudo docker run hello-world") I get the foll…

I have spent 7 hours now trying to connect to my Neo3 via my laptop using a USB to Ethernet Adapter. Ive also tried changing the nanopi microsd card image to see if it has any effect. from Ubuntu / Armbian / DietPi. When im powering on my Neo3, with ubuntu only the red led shows, with the other two, the Red LED shows plus the green LED flashes. Is this actually possible? Can I plug my Neo into my laptop with a ethernet usb adapter? or does it have to be into a router? The error im getting on my laptop is Connection Failed : Activation of network connection failed. the network manager shows it forever stuck on Connecting…

On a Rock 5B, I installed Armbian 23.11 Bookworm CLI via a SD card and now trying to setup boot via the NVMe drive. I followed the instructions on https://www.armbian.com/rock-5b/ to create a partition on the NVMe drive, format it, then tried `armbian-install` to boot from SPI. However armbian-install does not list the option to "Boot from SPI". It shows only the following options: 1 Boot from SD - system on SATA, USB, or NVMe 5 Install/Update the bootloader on SD/eMMC I then noticed I do not have a SPI device. /dev/mtdblock0 doesn't exist as well as "cat /proc/mtd" is empty. # ls /dev/mtd* ls: cannot access '/dev/mtd*': No such file …

I had one OPi5 setup and working properly with one of my TVs. I was running Kodi and using the remote from my TV to control Kodi using HDMI-CEC. I went to setup a second one on another TV but this time the TV remote did not work properly. Through elimination I came to determine the HDMI cable was the issue. I ordered another HDMI cable that had the Ferrite at each side of the cable. Now it worked properly. Thought this might be useful for others. This is the cable I ordered: https://www.amazon.ca/dp/B003PDHJ6M Conclusion: In order to make HDMI-CEC work properly, make sure the HDMI cable is of sufficient quality. I think ones with the Ferrite may be b…

Hello everyone. Please help me with the following problem. I have a Rock Pi 4b 1.4 (with SPI flash). I did the boot from the NVMe SSD using the image rkspi_loader-v20.11.2-trunk-v2.img according to the instructions. I installed Armbian 23.11 Jammy XFCE on NVMe SSD KingSpec NX 1TB. I’m using a power supply Baseus 65W GaN Pro (with PD). The system loads and works well. However, the system cannot reboot. When i click on reboot, the system starts to reboot and after the reset goes into a cyclic reboot. I need to turn off the power to reboot. What could be the problem and how to solve it? UART (Serial console) log: " " $&0 f@`B@@NF0f@`B@@NF 0f@`B@@NF@@@LN`b`N" " …

I booted the RC from 1/20/2024, set the ftdfile to rc3588s-orangepi-5b.dtb in armbianEnv.txt, and rebooted: no wifi or bluetooth. The hci0 and wlan0 devices are not present. They both work on the Linux 5.10 kernel. My armbianEnv.txt: -------------------------- verbosity=1 bootlogo=true overlay_prefix=rockchip-rk3588 fdtfile=rockchip/rk3588s-orangepi-5b.dtb rootdev=UUID=38eb4cb5-0503-4a0a-900f-7a5167517a20 rootfstype=ext4 overlays=sata1 sata2 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u

Hi all! There's a dedicated RTC chip in Rock3A (HYM8563TS), but unfortunately it doesn't work right with the standard Armbian image. The chip is correctly identified, but the problem is with the RK809 PMIC, which also contains an RTC. During boot RK809 is labeled as rtc0, and HYM8563TS as rtc1, and by default kernel uses rtc0 for hwclock manipulations. Since RTC battery is connected to HYM8563TS, after power cycle RK809 is reset to 2017-08-05 09:00:00. | _ \ ___ ___| | __ |___ / / \ | |_) / _ \ / __| |/ / |_ \ / _ \ | _ < (_) | (__| < ___) / ___ \ |_| \_\___/ \___|_|\_\ |____/_/ \_\ Welcome to Armbian 23.11.1 Bookwo…

Hello, i'm using the NanoPC-T4 with Armbian Bookworm (23.8.1 with Linux 6.1.63-current-media) Kernel and Mainsail/Klipper is running on in smooth and gently. Since i want to record timelapse videos, i've decided to buy the orginial "FriendlyELEC Cam1320 PI Camera Module" based on the OV13850. I've connected it in the expectation that it should work together. But the System is not detecting the camera module. $ v4l2-ctl --list-devices rockchip,rk3399-vpu-enc (platform: hantro-vpu): /dev/video2 /dev/video4 /dev/media1 rockchip-rga (platform:rga): /dev/video0 rkvdec (platform:rkvdec): /dev/video3 /dev/media0 rockchip-iep (platform:rockchip-i…

I am currently on Armbian 22.05.0-trunk with bleeding edge Linux 6.1.11-rockchip64 according to the main boot page in terminal I was in the process of converting an elegoo neptune 4 into a non-neptune version of klipper followed a guide that used a script was on the last step which was to do a system update...and upon reboot, I have no ethernet devices all I see is loopback what do I do to get my hardware ethernet interfaces back? this device does not have a removable SD card, but it does have a serial port... so everything must be done thru command line armbian monoitor.txt

Hello! Just wondered if an armbian image was planned for the Odroid M1S? Thank you in advance!

I first made a self-built image for nanopi-r2s and everything is fine. But another self-built image of Nanopi-R2S seems refuse to boot after enabling these configurations: `DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT`, then `DEBUG_INFO_BTF` and `MODULE_ALLOW_BTF_MISMATCH` But the LED on RJ45 blinks, and I can ping the IP that I get from my router DHCP, but SSH connection refused. So I guess it may have booted, but refuse SSH connection. I have no TTL serial connections yet, I'll check it and post the logs here some time later. Can anybody help? How can I enable ssh with? Is it possible to enable it at build stage? Thanks.

I have a project developed on Rock 4C+ v1.2 board. Now there is only v1.41 board available and Armbian is not booting on it at all, no matter it's compiled locally, or it's downloaded from the official sources. UART debug is producing unreadable sequence. So far, what I’ve tried: - I’ve built Armbian with the latest changes armbian build repo - hasn't helped - I’ve used rk3399-rock-4c-plus.dtb file instead of rk3399-rock-pi-4c-plus.dtb, dunno why there are two, but somewhere on the forum I read that this one without “pi” is the right one - hasn't helped - official Armbian images - not booting - Ubuntu and Debian - both booting fin…

Morning all, so I got myself a FriendlyElec CM3588 NAS board for testing and in the end integrating in my homelab. I tried a few Armbian images - FriendlyElec suggests the NanoPi R6S image and I tried the NanoPC T6 image. Both boot but both have some issues, e.g. no USB connectivity and no HDMI out (T6). While not a being developer or SBC specialist, I am a Linux user since 1995 (server)/1996 (desktop) and I am used to some pain, tinkering and problem solving. Is there any kind of "getting started with a new board"- or similar document that I could use as a starting point to tinker with this board? Any hints, advice? Of course I could use the …

Not at the time of generation, but Armbian is stuck on reboot, not going to heartbeat led nor getting IP, and does nothing. I have no idea how it is related and what I should do to: - restore boot; - apply a key without ruining the installation. OMV 6.9.11-4 (Shaitan) on Armbian 23.8.1 Bullseye SBC RockPi-4A 4GB RAM with Penta SATA HAT (PCIe to SATA 4-channel for RAID + 1 eSATA). Eugenijus.

Hello, As stated recently I had setup a Rock5B with Jammy/Mutimedia and had issues with a 2160P / 3840 x 2160 screen. Initially bootup would show a flickering screen. Adding the custom resolutions via cvt/xrandr and setting line in boot env: "exrtaargs-video=HDMI-A-1:3840x2160@60" fixed that issue However the initial login screen and logout screen resulted in a vibrant flickering background . This was on a Sceptre 50" TV and other perihperials would normally work fine. This took a while to figure out because I was confusing my active desktop provider and Gdm was being used: https://askubuntu.com/questions/91…

I tried to update my odroidm1 to 23.11.2 (from 23.8.1) by fresh install using Armbian_23.11.2_Odroidm1_bookworm_current_6.1.68 flashed to sdcard but when booting the device (holding recovery button) I see "Gave up waiting for root file system device." The same issue when using the other CLI images flashed to sdcard. Any idea how to fix this? When mounting the sdcard from a ubuntu system the uuid seem to match and the sdcard is mountable.

Hi, does anyone know how to get this working please? Thanks.

I have a problem on 2 rock-5b boards with emmc drives. on both I am unable to update the distro immediately after the first boot. On the firs SBC upon doing an apt upgrade I get: Setting up perl-base (5.36.0-7+deb12u1) ... (Reading database ... 27044 files and directories currently installed.) Preparing to unpack .../0-perl-modules-5.36_5.36.0-7+deb12u1_all.deb ... Unpacking perl-modules-5.36 (5.36.0-7+deb12u1) over (5.36.0-7) ... dpkg: unrecoverable fatal error, aborting: unable to fsync updated status of 'perl-modules-5.36': Input/output error E: Sub-process /usr/bin/dpkg returned an error code (2) W: Problem unlinking the file /var/cache/apt/pkgcac…

Hi, I use Helios64 from the begin and this board is very unstable according to my experience and many posts here... After many dialogue here and settings shared about Frequency and Governor Kernel... maybe i find the problem and i ask anyone return of experiences about the procedure and setting belong: - Connect USB Wireless Dongle or USB(-c) Ethernet Plug - Configure it - Disconnect all ethernet cable to the board - Use with last time crash configuration and do a endurance test your helios64 board Have a good day

The mainline 5.11 patch "phy: rockchip: set pulldown for strobe line in dts" https://github.com/torvalds/linux/commit/8b5c2b45b8f0a11c9072da0f7baf9ee986d3151e (not backported to 5.10.y) seems to have broken most if not all rockchip board EMMC HS400 enhanced strobe support. This probably affects supported rockchip boards (at least rk3399 ones, but probably most). That is boards exhibit: [ 18.985162] mmc1: running CQE recovery [ 18.988056] ------------[ cut here ]------------ [ 18.988500] mmc1: cqhci: spurious TCN for tag 12 and the filesystem ends up corrupted on write attempt. Note that another bug about regulator core DEFER…

i got below command in orangepi official databook, when i do like below, it can't start up(led flashes but nothing in display monitor). Not sure if the armbian supports the "dd" install?

I'm working on enabling secure boot on Orange Pi 4B. So far I was able to burn eFuses, sign rk loader, a trust image, and a uboot image. To extend secure boot chain to the Linux Kernel, I've enabled FIT_SIGNATURE in u-boot, and manually built FIT image (Linux Kernel, initramfs(initrd), and a kernel DTB). Now I want to add FIT image creation to the Armbian build system. What is the correct place/script to do it?

Hello, as said in the title The latest Armbian 23.11 images don't display anything but it seems to start well. Is it possible that this is incompatible with my screen?

Hello, The last image for orange pi 5 with kernel 6.7 doesn't contain the overlay rk3588s-orangepi-5b.dtb on /boot/dtb/rockchip. So there is no way to mount the emmc on the orange pi 5B Is it possible to download the binary overlay separatelly? Thank you.

Hello, I got a nanopc-t6, when trying to install mdadm or another package that regenerates initramfs or installs a new kernel, I get an error that there is no space in /boot. Can it be increased and how? Regards,

I wanted to upgrade from the previous release to the current one. apt update & apt upgrade and reboot worked fine but I noticed it was still on the 5.10 kernel so I used the config utility to switch to 6.7 and now I can't get a display output on HDMI 1 or 2 and its not getting an IP address either. I'm booting from M.2 NVME. Is there any way to fix my setup?

On my NanoPi R6C I downloaded the Armbian 23.11 Bookworm CLI and booted the machine from the SD card. Then I installed gnome and firefox. Most things works so far, but I get no sound over hdmi (there is no headphone jack). The gnome - settings - sound shows only the dummy device. Youtube videos play ok, but somewhat laggy and with very high processor load (all cores close to 100% on the gnome system monitor).

Wich Armbian destop version to use on PI 5b to be able to setup/use onboard wifi and BT ?

With my bigtreetech 7” hdmi lcd the orange pi 3b does not show image with edge kernel. It works with legacy. if i ssh it to it, dmesg show some error about unsupported mode and no crt connected. best regards Jesper

Hi, Today i make upgrade to 23.11 armbian on my Helios64. It's in bookworm version (apt source list is good, no change since 23.08) but now it display this: Welcome to Armbian 23.11.1 Buster with Linux 6.1.63-current-rockchip64 No end-user support: community creations & unsupported (buster) userspace! it's a bug? thank have a nice day

I installed the armbian image on an SD card and it runs fine. Now I would like to run it from the EMMC for long term reliability. i tried following what Dara Ó hEidhin did in this thread but am not successful For some reason google drive is not letting me download the driver assistant so RKdrivetool doesn't see the orange pi board like the video referenced in the thread so i cant flash it that way. I tried running it from the SD card and editing the armbianEnv.txt in the /boot folder from fdtfile=rockchip/rk3588s-orangepi-5b.dts to fdtfile=rockchip/rk3588s-orangepi-5b.dts and am able to see the EMMC drive. then i try a s…

Hi, I'm testing the latest Armbian 23.08 Bookworm on a Rock3A board. I have installed the Armbian base system on both SD-CARD and eMMC. For my application I need to use an Intel WiFi M.2 board, precisely an Intel AX210 NGW with both Bluetooth and WiFi enabled at the same time. Currently I have found this situation: boot from the SD-CARD (eMMC removed from its socket) Intel AX210 M2 card plugged-in the OS boots corectly installed the firmware-iwlwifi package and bluetooth+wifi works without problems boot from the eMMC memory (SD-CARD removed from its socket) Intel AX210 M2 card plugged-…

Hi people! I'm trying to use Armbian 23.8.1 CLI with the Rock 4 SE board without success. I write the eMMC in the classic way: xzcat Armbian_23.8.1_Rockpi-4b_bookworm_current_6.1.50.img.xz | sudo dd of=/dev/sdb bs=4M status=progress; sync but nothing seems to happens, i have only the green led on, the blue led is not blinking and the display says "no hdmi signal". No problems with the image from radxa. Do you have any idea what's going wrong?

Hello, As far as i know Orange PI 3B using the Rockchip RK3566, is this SOC support graphic acceleration? I am running Armbian 23.8.2 Jammy with bleeding edge Linux 6.5.2-edge-rockchip64, only 1 tab of Chromium with video player but the CPU reached 100% all time

Hello! On newer kernel (5.10.63+) gpio behaves strangely. Led connected to gpio pin blinking opposide status led. Also it break spi work. armbianmonitor logs https://paste.armbian.com/faqorefumi VID202304051140011.mp4

I installed Armbian on my R5s Armbian 23.8 Bookworm Kernel 6.5, Size: 479Mb, Release date: Sep 18, 2023 On this version, I find the classical problem : a module I want to build does not build. Reason ? apt says : Coundn’t find any package by glob ‘linux-headers-6.5.3-edge-odroid’ And make creates an error because “build” directory is not found. I can find the linux-headers-6.5.3 : https://cdn.kernel.org/pub/linux/kernel/v6.x/linux-6.5.3.tar.gz But where can I find the odroid version ?

Dear Armbians I have a NanoPi Neo 3 board with 1GB of RAM running in a DC for quite a while now. Because of an SD card failure, I had to make a fresh setup with the actual Bookworm image. This image seems to be quite unstable. Device is going up and down all the time. I am unable to find the problem myself. Maybe someone can take a look and help me to fix my stability issue: Debug output: https://paste.armbian.com/sozozoyahi

Hi, I have an issue with an USB device which is not detected; looking on other forum, it seems that additional modules shall be added: - cdc_acm,cdc_ether - rndis_host - rndis_wlan - usbnet I'm not able to load these using the modprobe cmd & checking loaded modules with lsmode cmd. I suspect that they are not part of the kernel. Any hint how to solve this, eventually recompile / install ? Thanks by advance, Samuel

I used iperf3 to monitor the LAN perferomance. It seems the LAN Port only runs on 100 Mbit how can I get a 1GBit speed ? Accepted connection from 192.168.xxx.xxx, port 64266 [ 5] local 192.168.xxx.xxx port 5201 connected to 192.168.xxx.xxx port 64267 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 10.7 MBytes 90.1 Mbits/sec [ 5] 1.00-2.00 sec 11.3 MBytes 94.8 Mbits/sec [ 5] 2.00-3.00 sec 11.3 MBytes 94.7 Mbits/sec [ 5] 3.00-4.00 sec 11.3 MBytes 94.9 Mbits/sec [ 5] 4.00-5.00 sec 11.3 MBytes 94.8 Mbits/sec [ 5] 5.00-6.00 sec 11.3 MBytes 94.7 Mbits/sec [ 5] 6.00-7.00 sec 11.…

Hello everyone, I would like to know which version of Armbian is recommended to install today to have a stable system ? Indeed, I have reset all my data on my Helios64 and I want perform a fresh install. I do not made any hardware change on my Helios64 and I plan to use OMV6. Thanks all for advices Flolm

I successfully booted this one and connected over Ethernet. Haven't checked WiFi yet. However, the observation comparing to the original Rockchip's Jammy image: the serial port goes quiet after the U-Boot fires up the kernel. The bootloader on the board and the _original_ kernel use non-standard 1500000 baudrate serial speed for the console. I haven't looked into Armbian's guts yet, but I assume it's a matter of right kernel boot arguments for this board to actually spit out kernel output over serial. What I'm not sure is if the console can be cloned between serial and UI over HDMI (console on the frame buffer if I'm right). I'm open to…

I have a rock 4b+ and I used it as an android box for a while. Then today I tried to flash it with latest armbian image (23.8.1) and it does not boot in microSD or when I flash it through USB OTG. I have erased the SPI flash completely and install the correct spi_loader. It also boots properly with Radxa debian image. Initially I though this is a boot issue, but after checking with a serial cable, it turns out this is a HDMI issue.. After I finish the usual procedure to setup password etc... I got this: Now starting desktop environment... root@rockpi-4b:~# [ 633.211385] hdmi-audio-codec hdmi-audio-codec.5.auto: Only one simultaneous stream su…

Hi, i use a Rock Pi 4b with a external USB3 Seagate 4TB HDD on USB3 Port on RockPi 4B. Der HardDisk ist ext4 formatet und mounted via fstab The maximum troughput over Samba Share is around 11 Mbit The same USB HDD on a Odroid with same samba settings has an troughput over 100 MBit Any Ideas ? Thanks Ingo

ArmSoM-LM5 uses Rockchip RK3588, a new generation flagship eight-core 64-bit processor with a main frequency of up to 2.4GHz, a 6 TOPS computing power NPU, and can be equipped with a maximum of 32GB of large memory. It supports 8K video encoding and decoding and adopts LGA packaging, which has stronger transmission capability and stability. It has rich interfaces and supports multiple hard drives, Gigabit network, WiFi6, 5G/4G expansion and a variety of video input and output. Supports multiple operating systems; provides baseboard reference design materials, allowing users to customize in depth. Applicable to ARM PC, edge computing, cloud server, artificial intelligence,…

Hi, how can I check the serial number of the RK3328 chip? with the distro from orangepi I can use cat /sys/devices/platform/board/info and with ArmBian ? thanks

After happily using my helios64 with armbian buster for years I finally dared to upgrade and everything went smoothly. I found instructions somewhere here in this forum and this is what I did. I first commented out /etc/apt/sources.list.d/armbian.list Then I upgraded to bullseye by replacing everything buster with bullseye in /etc/apt/sources.list (I think I also had to change the url to the security repo) Then I did apt-get update && apt full-upgrade and rebooted. Great success! Then the same for bookworm and again great success. Then reenabled the armbian …

My audio volume was very very low, and very annoyingly I had to boost to 200% 300% which had the problem that the volume buttons were not working properly. You just cant see anything above 100% unless you go into the control panel. Now when it comes to audio I'm the village idiot, but I found a proper solution I think. After some experimentation I found that the module "module-cli-protocol-unix" ( #20 in my case) can be amplified with pactl set-sink-input-volume 20 10db Now YMMV depending on your attached hardware, so change the 10db to whatever suits your situation. After that I made it permanent by adding it to the /etc/pulse/default…

I followed all online guides. I tried to flsh the SPI. I arrived to the point where the maskroom is well recognized by the computer (Linuxmint). After that I tried to flash it and the error code is that the write operation is impossible. Please do you have any suggestions? Thanks.

Armbian Jammy Gnome desktop and following those commands to enable 3D acceleration : then the mpv can not play any .avi files , Terminal output “segment error” . but .mp4 files can be played normally . and I tried running mpv using root or sudo to play .avi files , it can played normally . I am very troubled by this issue, please provide assistance.

The image is coped on SD using: sudo dd if=Armbian_23.8.2_Orangepi3b_bookworm_edge_6.5.2.img of=/dev/sda bs=1M status=progress The initial startup is fine (booting, setting of root password, user name/password, wifi setup as well as locales/tzdata). We obtain a system with working internet connection, it can be upgraded using apt etc. However, after reboot wifi fails (the first impression was that we installed something wrong during upgrade phase. However, the sequence: fresh sdcard boot, armbian initialization, reboot (through the reboot command, not a button)) still results in the following: 1708 [ 6.944457] WCN_ERR: read marlin3E chip id fail, r…

Armbian_23.8.2_Orangepi3b_bookworm_edge_6.5.2.img boots, runs, and installs OK on Orange Pi 3B. Tested on 4GB RAM model with 256GB eMMC. - WiFi works* - HDMI audio works - 3D acceleration Panfrost driver works I installed xorg, mesa, x11vnc, jwm, pulseaudio, and flatpak native packages, which was followed by adding Kodi flatpak. Everything worked - with one caveat: there is a delay between keystrokes and output. Typing locally is fine, the problem manifests itself during an inbound SSH connection or when using a remote control app for Kodi on Android mobile. I have tried first replacing pulseaudio with pipewire (no change), making su…

Just stumbled over another chromium fork: https://github.com/Alex313031/Thorium Forum search did not show any entries, so I thought I might share. The arm64 builds (for raspberry though) works great, it even has googly sync, widevine etc, check describtion for more info. It works out-of-the-box on legacy rock-5b jammy gnome images with liujianfeng1994 ppa enabled. For installation/updates one could also use: wget https://dl.thorium.rocks/debian/dists/stable/thorium.list sudo mv thorium.list /etc/apt/sources.list.d/ sudo apt update sudo apt install thorium-browser I usually like to test https://paveldogreat.github.…

My device is Station-M3. I download "Armbian 23.8 Bookworm Cinnamon image" and burn it to a sd card.When armbian startup ,display response is very slow and Cinnamon process occupy 150% and above cpu usage.So I decide to "Enable 3D Acceleration".I do this as follow: sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia sudo apt update sudo apt dist-upgrade when dist-upgrade has done,something wrong about libc6, maybe because V2.36 is replaced by V2.35.Then the whole system come to unstable，reboot only bring kernel Panic！ I decide to burn the image again，but how can I enable GP…

Hi, working on Rock Pi 4B++ and trying to make our displays work. Armbian Bookworm 23.8 Raspberry Pi 7" official touchscreen Officialy supported by Radxa (https://wiki.radxa.com/Rockpi4/Raspberry_Pi_official_LCD) but it does not work on Armbian at all. Works on official Radxa Debian image. No display on Armbian. Using device tree overlay from Radxa image - does not work, of course. Waveshare 4.3" touchscreen HDMI (https://www.waveshare.com/wiki/4.3inch_HDMI_LCD_(B)) It works. Image is visible, touchscreen works but the resolution seems to be scrambled. It is 800x480 and it is correctly reported, but the image is somehow distorted. I …

I have been trying to research this and have come up a bit blank. I am trying to figure out if I need to do anything special to enable panfrost. I have built a jammy and bookworm image using the stable kernel. Both boot fine, but are both using llvmpipe. It does look like its trying to use panfrost. Inside of dmesg: [ 20.098662] panfrost fde60000.gpu: clock rate = 594000000 [ 20.098685] panfrost fde60000.gpu: bus_clock rate = 500000000 [ 20.098820] panfrost fde60000.gpu: Looking up mali-supply from device tree [ 20.099041] panfrost fde60000.gpu: _of_add_opp_table_v2: no supported OPPs [ 20.099287] panfrost fde60000.gpu: devfreq init failed -2 [ 20.09930…

Dear to all, I have a Helios64 unit with 2 hdd (both WD60EFRX). I have bought also an external enclousure UGREEN 5 Bay Hard Drive Enclosure ( https://eu.ugreen.com/collections/hard-drive-enclosures/products/ugreen-5-bay-hard-drive-enclosure-5-x-18tb-raid-array-hard-disk-docking-station ) and 2 WD140EDGZ and these 2 hdd are mounted inside UGREEN enclousure because I want format and test it (when all will work fine I'll exchange a WD60EFRX with a WD140EDGZ so the drives inside the enclousure will have a backup scope). The enclousure is powered by external adapter, the system image installed is the Armbian 22.02.1 with Linux kernel 5.15.93-rockchip 64 and openmediavault 6.6…

I've been looking into streaming on the Orange Pi's, which doesn't work, so I thought I would share my findings. I was first told by customer service people that the problem was HDCP, but have found that it is actually the camera. The tech was kind enough to slip that the camera module doesn't have their hooks. I can still view in the browser, and this leaves me to the conclusion that TV boxes and Smart TVs are using the camera modules to record end users without their permission. If the system has the camera hooks, the app is allowed to play. The browser bypasses this, because it has permissions to access private information on our device…

Hello I have two Rockpi A (without wireless) since I have upgraded to latest kernel: 6.1.50-current-rockchip64 One of the two USB3 port is not working, the top one (from usb-devices and lsusb I don't see any special difference) it seems USB2 port are ok same issue on two rockpi cards, I have try many usb devices (storage, network etc...) without success I am alone with this issue ? armbianmonitor send to http://ix.io/4IE9 Rgds

I don't expect an answer at this point but FYI, the eMMC on a Rock5a and latest image does not work properly. It mounts and as soon as you start writing, errors occurs and the FS (ext4) is remounted RO. It happens whether I mount and write manually or I use the armbian-config to transfer the system on the eMMC. Using the Debian distro of radxa, I can write as much as I want on the eMMC w/o errors, so it does not seem to be a failed module, rather something in the armbian kernel. 2023-10-10T17:05:03.106367-07:00 rock-5a kernel: [62335.087809] Buffer I/O error on device mmcblk0p1, logical block 648585 2023-10-10T17:05:04.109720-07:00 rock-5a kernel: [62336.091…

Hi - First, thanks for building armbian, it's so useful! I'm a bit confused with the status of Rock 5A. I saw the link in the 5B section to download the 5A which directs me here https://mirror-us-phx1.armbian.airframes.io/dl/rock-5a/archive/ to a 23.8.3. But I can't find any other desktop version except the XFCE one. Now, if I go there https://k-space.ee.armbian.com/archive/rock-5a/archive/ I have a cinnamon desktop version but it's a 23.5. Is there no build for 23.8 + cinnamon or is this a mirror issue? Or is the Rock5A not yet officially supported and I should move my question?

Hi, I've got a Helios64 device running with OpenMediaVault 6.9.2-1 (Shaitan). kobol@helios64:~$ uname -a Linux helios64 6.1.50-current-rockchip64 #3 SMP PREEMPT Wed Aug 30 14:11:13 UTC 2023 aarch64 GNU/Linux It has been stable until I recently install openmediavault-photoprism 6.0.9-1 plugin provided by OMV6 through a podman container. I want to use PhotoPrism to help categorize my photos. The issue is my device systematically reboots during photo folder initial scan: the scan actually loads the system a lot, and in this state of activities, a reboot occurs after about 30 minutes to 4 hours. I first thought of a CPU temperature is…

Hey there, I'm running Armbian 23.8.1 Bookworm with Linux 5.10.160-legacy-rk35xx on a Rock 5B and am trying to get zfs via dkms to work, but it won't compile. ... configure: error: *** None of the expected "file_fallocate" interfaces were detected. *** This may be because your kernel version is newer than what is *** supported, or you are using a patched custom kernel with *** incompatible modifications. *** *** ZFS Version: zfs-2.1.11-1 *** Compatible Kernels: 3.10 - 6.2 Error! Bad return status for module build on kernel: 5.10.160-legacy-rk35xx (aarch64) I'm attaching the full build log,…

I changed this in the dt and got more than double the speeds from my Samsung U3 SD card: However I have no idea what the process of getting this into the kernel source looks like. --- rk3399-rock-pi-4b.dts 2023-10-04 15:36:05.031221270 +0200 +++ rk3399-rock-pi-4b-mod.dts 2023-10-04 00:34:15.773888431 +0200 @@ -342,6 +342,7 @@ disable-wp; pinctrl-names = "default"; pinctrl-0 = <0x26 0x27 0x28 0x29>; + sd-uhs-sdr104; phandle = <0xce>; };

GPU can perform far better than CPU cores for certain applications. Computer vision is one of them. Orange Pi 5 GPU has 64 shading cores. It runs up to 19 times faster than 8 CPU cores combined for computer vision models. Armbian on Orange Pi 5 supports OpenCL driver for compute-intensive GPU programs. To install OpenCL on Orange Pi 5 Armbian, follow the instructions in the following link; Install OpenCL on Orange Pi 5 Armbian

FF 115.3.0esr often freezes if WebGL is enabled. Test your browser here: https://get.webgl.org/. And you can disable WebGL as mentioned there: https://support.mozilla.org/en-US/kb/upgrade-graphics-drivers-use-hardware-acceleration#w_disabling-webgl. More information about Orange Pi 5B in my wiki (including how to enable hardware acceleration in Armbian based on Debian 12.1.0): https://dragonserw.ru/arm64:orangepi-5.

Hello guys! 🙂 I used to configure latest Armbian @ Orange Pi 5 B in such particular way: https://dragonserw.ru/arm64:orangepi-5. The problem is: Gnome settings does not save. As for now, I extremely need to set my screen off after 15 minutes of inactivity. How can I do it from command line? My hardware: dragonserw@orangepi5:~$ inxi -b System: Host: orangepi5 Kernel: 5.10.160-legacy-rk35xx arch: aarch64 bits: 64 Desktop: GNOME v: 43.6 Distro: Armbian GNU/Linux 12 (bookworm) Machine: Type: ARM System: Orange Pi 5B details: N/A CPU: Info: 3x 4-core Model N/A [MCP AMP] speed (MHz): avg: 2064 min/max: 408/1800:2352:2304 Graphics: Device-1: disp…

I was cleaning storage room of customer and found this device in sealed box. Owner of the box say it was rarely used and i can keep it. Only thing broken was the battery. I replaced it temporarily with unused smartphone one. The device boots and is almost new condition. SoC RK3066 = (ARM Cortex-A9 Dual-Core @ 1.6Ghz + ARM Mali400MP4) RAM 1GB = (Four Chips on image are Hynix [H5TQ2G83CFR-H9C] -2gb) Storage 16GB = (Toshiba TH58TEG7DCJTA20 - Nand Flash MLC 16GB) Uart RX/TX pads on board I make this topic as i want to ask more experienced people here if this SoC can run "some" version of Armbian. Thank you in advance

Hi, I'm seeing the following error in Chromium when trying to play youtube, the video loading screen never opens the video. I have installed chromium-browser (+libv4l-rkmpp, +ffmpeg, +rockchip-multimedia-config) from the ppa: https://launchpad.net/~liujianfeng1994/+archive/ubuntu/rockchip-multimedia My OS version is Armbian 23.08 Jammy. When using FFplay the rkmpp hardware decoder is able to correctly decode h264 and hevc content, so there does not seem to be a problem with rkmpp. Any thoughts on what could be wrong? I found another guy who had the same issue, but there was no resolution: https://github.com/armbian/build/issues/5384 Faile…

Hi. At first I'd like to apologize for the tone of this post, but there are things that I've been fighting with, without any success, for a long time. Problem 1. I have, as it seems, a very common problem with Armbian on RK3399. I burned Armbian 23.8.1 for the Rock Pi 4C+ onto an eMMC module, which booted, but there is no HDMI video output. I can't SSH into it over ethernet and provide more details because the server is disabled by default. I assume that the problem here is the same one as I often see coming back to all RK3399 boards and the solution is always the same - "libreelec patches for the HDMI subsystem" (whatever they are). If it'…

I updated my Helios64 last night and now it keeps rebooting. Every now and then it runs for a few minutes so I can log in via ssh and then it reboots all at once. Installed on the system is only OMV 6.9.1-1 (Shaitan) and Docker with the image of Emby. the system runs on an installed M.2 SSD on slot 1. 4TB WD Reds are installed in slots 2, 3 and 5. Welcome to Armbian 23.8.1 Bullseye with Linux 6.1.50-current-rockchip64 No end-user support: community creations System load: 9% Up time: 4 min Memory usage: 17% of 3.77G IP: 172.18.0.1 172.17.0.1 192.168.180.5 CPU temp: 42°C Usage of /: 7% o…

I use Armbian_23.8.1_Rockpi-4cplus_bookworm_current_6.1.50_xfce_desktop and need the current headers but could not find them sudo apt search linux-headers do not show them. I need them for the procedure described here https://github.com/glasgowneuro/comedi_raspberry_pi_bullseye/tree/main in order to install missing kernel drivers (comedi usbdux-sigma) Can anyone help please!

Hi! How can I install the edge kernel while still being able to boot armbian and keeping the built-in wireless module working? Is there any firmware for this module at all for kernel 6.2?

After recent kernel update, USB3.0 ports no longer work, There is an error printed in kernel log. [ 2.826383] phy phy-ff800000.phy.6: phy poweron failed --> -110 [ 2.827119] dwc3 fe900000.usb: error -ETIMEDOUT: failed to initialize core [ 2.827881] dwc3: probe of fe900000.usb failed with error -110 I found this issue in NanoPC T4, but it might also appear in other RK3399 boards. lsusb didn't show any USB3.0 controller. Confirmed this isn't my hardware's problem, another board have this issue too. dwc3.txt

Hello guys! I bought https://aliexpress.ru/item/1005005675856892.html. As I know, there is no 3D acceleration in Debian Bookworm. So, my desigion is to install Armbian Jammy Gnome desktop. My questions are: 1) In what moment should I perform trick ? 2) Legacy is the only system I can install, or is it any way to install current system? I wish kernel v6 to be installed, but not the RC kernel. My experience with SMB is Rapberry Pi 3 B and 4 B. I used to install only Raspbian on that boards. Wish me luck guys :-))

Hi, I have tried multiple Rock Pi 4+ (Plus) boards, all of them run regular Debian well, so the hardware should be good. But when I tried Armbian, the 2 USB 3.0 ports were not working with logitech USB dongle or Samsung USB drives (which did work in regular Debian), I searched and found maybe they were in OTG mode and needed to be in HOST mode. I tried armbian-config then System -> Hardware, then enabled: dwc3-0-host rockpi4cplus-usb-host After reboot, the bottom USB 3.0 port would start working, yet the top one still wouldn't work. Otherwise, Armbian was the most user-friendly, fast and stable…

It seems a package is missing from the Armbian 23.8 Bookworm CLI that results in this error. I encountered an add-apt-repository: traceback error. To fix it just run: sudo apt install python3-launchpadlib

I don't have a NanoPC-T4, but I have a NanoPC-T6 which I mainly bought because of the Dual Camera options of the MCAM400 on the T4 and the high-speed encoding properties of the Rockchip... those possibilities should be very similar for the T6 actually... Whatever, the camera configuration seems to be mostly here but I struggle to do the similar thing with the device tree of the T6... Anyone who has an idea about this and is willing to help me with that?

I am trying to update my Banana Pi M64: missinglink% cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=bananapim64 BOARD_NAME="Banana Pi M64" BOARDFAMILY=sun50iw1 BUILD_REPOSITORY_URL=https://github.com/armbian/build BUILD_REPOSITORY_COMMIT=869a89d6-dirty DISTRIBUTION_CODENAME=focal DISTRIBUTION_STATUS=supported VERSION=20.05.4 LINUXFAMILY=sunxi64 BRANCH=current ARCH=arm64 IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image but when I run this command: missinglink% sudo apt update && sudo apt dist-upgrade -y I get these errors: W: An error occurred durin…

Hi, please provide me with link where can I download OS - armbian or ubuntu built for the board OrangePi 3B with RK3566 CPU. http://www.orangepi.org/…tml Thank you very much.

What Works: - USB2 and USB3 - PCIe2 - GMAC - eMMC on HS200 mode - Cpufreq - User and maskrom buttons Dmesg Output: https://paste.armbian.com/onelomofit You can download them from Rolling releases section on https://www.armbian.com/nanopi-r6s/ page. Images include devicetrees for R6S and R6C. If you have R6C, you must change the devicetree from armbianEnv.txt.

Hi there, https://www.armbian.com/rockpi4/ I see there are specific builds for versions. Version A, the link does not contain an image. Does the general image work on all versions? or the link is simply broken? Kind regards

How to install mali gpu driver for orangpi 5b with debian bookworm image ?

As you can see the WAN-port/NIC registers fine with a label from the nanopi-r6c device tree $ grep fe1c0000 /boot/dtb/rockchip/rk3588s-nanopi-r6c.dtb grep: /boot/dtb/rockchip/rk3588s-nanopi-r6c.dtb: binary file matches dmesg: dmesg | grep fe1c0000 [ 7.287277] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID [ 7.287373] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 7.287377] rk_gmac-dwmac fe1c0000.ethernet: DWMAC4/5 [ 7.287381] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported [ 7.287385] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported [ 7.287388] rk_gmac-dwmac fe1…

I don't know if this is the right subforum for this question. Would Armbian be possible for the PineTab2?

Hello, after some u-boot test, my helios64 don't start the bootloader stage. I can etablish a serial connection on USB Type-c port, but when I tried to start the system, I have no output on it. After I disconnected everything : - I connect usb-c cable, I'm able to connect to serial console with picocom - I connect the power cable, The LED1 (System Rail Power) is on, and the LED9 (Battery Status) flashes. - I press the power botton (without sdcard) : - LED2 and LED3 (Periph. Rail Power and HDD Rail Power) are on - LED4 and LED5 (System ON and HDD Activity) are on. - nothing happen on serial console - If I keep SWI (power …

I'm trying to setup disk encryption, but for some reason its not opening devices after installing cryptsetup-bin on the installation image. After typing the password it just hangs and does nothing $ cryptsetup open /dev/sda sda_crypt Anyone?

Hello, I have been able to boot the offical debian image recommend for the rock pi 5b from a NVME SSD. This is after updating the SPI using the windows software. I now cant seem to get armbian to boot from NVME or SD card. I have serial access to the Rock 5b and get the following see attached. Anyone able to point me in the correct direction. I think i need to flash the rock pi so it boots from SD once more. Thanks Matt Rock 5b Armbian fail.txt

Hello, i have trouble with my Helios64 (possibly bricked), so I am interested to by a new one. And if i can fix mine, the second one could allow me to participate to armbian support for it. Anyone have one for sale ? Preferably in Europe. Thank you.