Allwinner sunxi

Hi, Thanks to the hard work of your team, the Pine64-plus touchscreen now works great with the mainline kernel and legacy images are no longer listed in the download options, but it looks like some of the instructions at https://www.armbian.com/pine64/ are still referring to the "old way" of doing things: ie: Pine64’s own LCD with touchscreen support can simply be activated in /boot/armbianEnv.txt by setting pine64_lcd=on and adding gt9xxf_ts to /etc/modules followed by a reboot. The LCD screen is now activated by manipulating the DT overlays, which can even be done from armbian-config - hardware, and the touchscreen module is…

• 0

  Reputation Points

• 2 replies
• 4.1k views

Learnincurve

January 18, 20215 yr

Hi, I've changed the default console from ttyS0 to ttyS3, using the mainline kernel with overlay "/boot/dtb/allwinner/overlay/sun50i-a64-uart3.dtbo". Unfortunately when I run command "sudo shutdown -r now" (or sudo reboot) my pine shuts down instead of reboot (although the console output says "reboot: Restarting system" at the end.) [Hard reset reboot works with "reboot -f" using ttyS3 console]. Using the standard console I can reboot my pine without problems. What could case this behavior? Is it necessary to disable or kill a ttyS3-process before the reboot?

• 0

  Reputation Points

• 2 replies
• 3k views
• 1 follower

linda

April 3, 20188 yr

I tried to get armbian running on my new pine64. Therefore I downloaded the latest two 7z-files for debian and ubuntu. But neither of them does an auto-resize nor does the first boot took more than 30sec - contrary to the documentation. I'm using the SD cards delivered with the pine64 (16GB). In a related post I've found there has been "update-rc filesystem defaults" to (re-)trigger the process (or update.rc). Neither nor I've found. How can I get the distribution created in the correct way on the SD card?

• 1

  Reputation Points

• 2 replies
• 4k views

UnixOutlaw

December 1, 20169 yr

I'm running Armbian 20.08 Focal on a Pine64 with 2GB RAM. Mostly everything runs fine, but I do have a problem with getting audio out of the headphone plug. In pavucontrol I can see audio is playing (an internet stream) on Built-in Stereo, but nothing can be heard when connecting speakers. To be clear: I don't want audio out of HDMI, but just from the headphone plug. I have also played around with alsamixer and unmuted everything that was muted and turning up the volume, but still no audio to be heard... Has anybody gotten this to work?

• 0

  Reputation Points

• 2 replies
• 3.5k views

Pander

April 22, 20233 yr

Hi everyone, I'm using Pine64 LTS for a project. According to AXP803 datasheet Page37 & 38, the charge LED indicator can be set to Mode A or Mode B. Does anyone know how to change this setting via sysfs, or other interface(I2c, Uart) ? pine@pine64so:/sys/class/power_supply$ ls axp20x-battery axp813-ac pine@pine64so:/sys/class/power_supply$ cd axp813-ac pine@pine64so:/sys/class/power_supply/axp813-ac$ ls device health input_current_limit online power present subsystem type uevent voltage_min pine@pine64so:/sys/class/power_supply/axp813-ac$ cat uevent POWER_SUPPLY_NAME=axp813-ac POWER_SUPPLY_HEALTH=Good POWER_SUPPLY_PRESENT=1 POWER_SU…

• 0

  Reputation Points

• 2 replies
• 3.4k views

Igor

April 20, 20197 yr

I've been having issues lately with the later versions 22.11 and above. At some point when I reboot, I'll get those 3 "Read-only file system" messages on boot: mkdir: cannot create directory ‘/root/.cache/oh-my-zsh’: Read-only file system rm: cannot remove '/root/.zcompdump-orangepizero2-5.8': Read-only file system zsh: locking failed for /root/.zsh_history: read-only file system: reading anyway What is happening?!

• 0

  Reputation Points

• 2 replies
• 5.9k views
• 1 follower

cekubalim

December 27, 20223 yr

I am currently developing a custom board which is based of the Pine64/Pine64-R18 dev board. I previously had an issue with the ethernet not working at u-boot level using the sopine based R18 board, this I resolved by patching u-boot with the relevant emac sections that were missing from the device tree. On the custom board we have used the R18 processor with the LAN8720 ethernet-phy chip rather than the RTL8211 used by the pine, and can't get the ethernet to initialise. We have checked rmii clock timings etc and compared the custom board to the Pine and have noticed the following:- MDC has been measured to be running at 18.6Mhz, resultin…

• 0

  Reputation Points

• 2 replies
• 3.5k views
• 1 follower

Gavinb

September 7, 20188 yr

When I tried using a c++ library called sfml which tried opening a window and it gave me an error and after trying every solution on the internet I gave up. And after trying other Debian images I noticed all of them don't have a desktop environment pre installed. So does Debian have graphics at all?

• 0

  Reputation Points

• 2 replies
• 3.2k views
• 1 follower

oleksii_laa

July 23, 20251 yr

Just for curiosity, I've updated my Armbian on my Pine64 to the latest release. The latest u-boot for Pine64 (U-Boot SPL 2017.11-armbian (Jan 25 2018 - 08:32:21) seems to have an issue with the persistent u-boot environment. Once I've written a custom environment back to MMC using `saveenv´ the board hangs during boot. Environment size: 10335/131068 bytes => saveenv Saving Environment to MMC... Writing to MMC(0)... done => reset resetting ... INFO: PSCI Affinity Map: INFO: AffInst: Level 0, MPID 0x0, State ON INFO: AffInst: Level 0, MPID 0x1, State OFF INFO: AffInst: Level 0, MPID 0x2, State OFF INFO: AffInst: Level 0, MPID 0x3, State OFF …

• 0

  Reputation Points

• 2 replies
• 2k views

umiddelb

February 2, 20188 yr

Hi, I've been trying to get my DS1820 temp sensor working but cant seem to get the device to show up om my orange pi zero 2 running Orange Pi 3.0.6 Bullseye Most info i find starts our with run armbian-config but orangpi doesnt have it. All i got is the orangepi-config but it doesnt have the "Go to the “system” section and select “Hardware” then activate w1-gpio." so i was looking arround and found you need to enable overlays in /boot/armbianEnv.txt but dont have it aswell but the alternative /boot/orangepiEnv.txt there i add the /boot/orangepiEnv.txt overlay_prefix=sun50i-h616 overlays=w1-gpio param_w1_pin=PC8 …

• 0

  Reputation Points

• 2 replies
• 5.1k views
• 1 follower

bjorns

February 26, 20233 yr

I have been reading into this for some hours now, and it seems like I will need to write (or perhaps modify from some existing) DTB overlay or something like that? I tried following the instructions here, and using a .dtbo file (hifiberry-amp100.dtbo) I copied from OSMC I have here on an RPi 3, but I don't think that's right as it mentions 'brcm,bcm2835' which I suppose means it can only be used with RPi. The above mentioned .dtbo file seemed to be in some binary format, although I could still make out some text in it. I can't even seem to find the uncompressed (plain text) versions, I searched OSMC and HiFiBerry repos (amongst others), I don't th…

• 0

  Reputation Points

• 2 replies
• 3.6k views
• 1 follower

TonyMac32

April 13, 20242 yr

I have a feeling this was caused by a p[roblem with the definition of ftdfile variable: line from boot.cmd: load ${devtype} 0 ${fdt_addr_r} ${prefix}dtb/allwinner/${fdtfile} from the serial output: File not found /boot/dtb/allwinner/allwinner/sun50i-a64-pine64-plus.dtb ** note the duplication of Allwinner. Since I couldn't find where it was defined , I just copied the allwinner directory into itself.....:-) which fixed the problem. Perhaps someone could look into this? thanks.

• 0

  Reputation Points

• 2 replies
• 2.4k views

belfastraven

December 1, 20178 yr

First off, I would like to give the crew at Armbian a huge heartfelt thanks for all the awesome work you do under sometimes trying conditions. I would like to present Archian, the bastard child of Armbian & Arch. Why … well, the project I am working on needed current versions of phosh & plasma-mobile and the versions on jammy/bookworm were quite old. The OPi supplied image was quite flaky so I had to find a way to mash these together. And this is the result. It does need to be run as root ! The script has 3 arguments: init - downloads the armbian image file, arch rootfs and arch packages. You need to then write …

• 0

  Reputation Points

• 2 replies
• 6k views

Curious

November 17, 20241 yr

I wanted to try anything other than the original image that the device came with. I was more interested in the Kali port but after trying for a few hours with pretty much all the images available here I had to revert to the original one. So I was wondering if anyone here ever tried these images or could give me some hint on what is wrong with it ? Basically just getting a red led with no display when trying all the images. I know the original image had a some sort of special boot process where the initial startup would take some time but I know nothing else about armbian at this point. My goal was to start doing some test with kali liking t…

• 0

  Reputation Points

• 1 reply
• 2.1k views

Igor

April 7, 20251 yr

Hello, First of all, thank you so much for putting these images together. Kudos to you all for some great work! Now on to my issue. I installed Xenial build and it booted up nicely to XFCE. The only issue I am having is no audio over HDMI. I know the display works for HDMI audio as my nVidia Shield works fine. Any help on determining the issue? If you need any logs, boot messages, and/or config files, let me know. Thank you in advance, Brian

• 0

  Reputation Points

• 1 reply
• 2.9k views

Igor

July 11, 20188 yr

Hello, Hopefully a maintainer is reading- is there a plan to build/release 24.8 for Orange Pi Zero 2? Thanks!

• 0

  Reputation Points

• 1 reply
• 3k views

Werner

October 22, 20241 yr

My OPIZ2 was working happily with Armbian_bullseye 22.11, but due to the wifi issue, I download the Armbian_bullseye_22.02 dan flash the image into the same working SD card (overwritten). But now my OPIZ2 would not boot anymore, nothing seen in the serial communication either. No red/green LED ever lit. Sadly, this is my 2nd dead OPIZ2..... Seeking for help if those boards are still recoverable...

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Werner

January 6, 20233 yr

I've got an Pine64 a that was one of the Kickstarter models. For a couple of years I've been running OctoPrint on it to run my Qidi i-mates 3d printer. Recently I decided to update from jammy to noble, before I did that I made a backup of my OctoPrint settings and files through the OctoPrint GUI in case of problems. I got a really messed inconsistent with all sorts of dependencies errors because the apt dist-upgrade seemed to freeze and after several hours of no movement I rebooted. As expected it was the mess. I spent about an hour on fixing dependencies but decided it just wasn't worth it as the only thing running is OctoPrint. When I went to restore OctoP…

• 0

  Reputation Points

• 1 reply
• 2.4k views
• 1 follower

laibsch

June 26, 20251 yr

Hi, Is possible to solve problem ? After reboot command orange pi zero 2 not want start and it stay turner off . I read article about changing R_WDOG instead of WDOG in ATF fix for different boad: Thanks

• 0

  Reputation Points

• 1 reply
• 3.5k views

cabanak

November 8, 20223 yr

Hello. The BigTreeTech TFT35 SPI works well but has ghost touches. So it's unusable for control tasks like on a 3D printer. It gives random commands to the printer from time to time, which can be dangerous. There is a patch from BigTreeTech since 24-1-2024 https://github.com/bigtreetech/CB1-Kernel/commit/ab7b1fa6ddd7f15ecdc590d32a812589fa38d973 I cannot find it on https://github.com/armbian/build/blob/main/patch/kernel/archive/sunxi-6.6/patches.armbian/add-bigtreetech-cb1-dts.patch and I can confirm that I have this problem with Armbian 24.8.1 Bookworm. But not with BigTreeTech 2.3.4 image. Could someone add these patches to the armbi…

• 0

  Reputation Points

• 1 reply
• 3.5k views

JohnTheCoolingFan

December 17, 20241 yr

Hi, Just want to check what the recommended approach is with today's dist-upgrade. I noticed that armbian-bsp-cli-pine64 was held back, so tried a manual install to see what the problem was. Seems like apt wants to remove linux-focal-root-current-pine64 to upgrade armbian-bsp-cli-pine64. Is this a temporary dependency issue? Obviously not performing the upgrade unless informed of the correct approach. BR.

• 0

  Reputation Points

• 1 reply
• 3.1k views

Igor

May 25, 20215 yr

Hi, I was unable to get static MAC address working on my Pine64. I have the kernel boot argument, console=ttyS0,115200 root=/dev/mmcblk0p1 rootwait rootfstype=ext4 panic=10 consoleblank=0 enforcing=0 loglevel=1 mac_addr=3a:bd:50:94:8b:06 But still, the from dmesg, [ 12.954581] sun8i-emac 1c30000.ethernet: device MAC address slot 0 aa:90:02:81:eb:e9 In the interfaces file, auto eth0 iface eth0 inet dhcp hwaddress ether 3a:bd:50:94:8b:06 But this caused error in ifup and system start up (networking cannot start since ifup failed with device in use) Although ifup failed, eth0 is visible in ifconfig, which means something else had already …

• 0

  Reputation Points

• 1 reply
• 3.7k views

tkaiser

December 21, 20169 yr

Found an interesting way to keep the Pine64 cool. https://www.youtube.com/watch?v=VFq1EbWOfYo

• 0

  Reputation Points

• 1 reply
• 2.7k views

Dan25

February 24, 20179 yr

Hi have Armbian_5.30_Pine64_Ubuntu_xenial_default_3.10.105_desktop installed and it all works well. How do I configure it so that if no keyboard is plugged in that a virtual keyboard is displayed?

• 0

  Reputation Points

• 1 reply
• 4k views
• 1 follower

debianxfce

August 15, 20179 yr

I have a brand new Pine H64-B. I can get AOSC to start on it, but needed to get Ambian to work. It will partly boot up, but never gets to the the CLI or desktop I have a good SD Card (AOSC works fine, works on a Pi; tried 32G and 128G, ) and power supply. Armbian_5.89.190626_Pineh64_Debian_stretch_dev_5.1.12.img Armbian_5.88_Pineh64_Debian_stretch_dev_5.1.7.img Armbian_5.88_Pineh64_Ubuntu_bionic_dev_5.1.7.img They get up to: Welcome to Debian GNU/Linux 9 (stretch)! ... snip ... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Kernel Device Manager. [ OK ] Started udev Coldplug all…

• 0

  Reputation Points

• 1 reply
• 3.9k views

Igor

July 7, 20197 yr

Hi. Is there no support for btrfs in the latest armbian-ubuntu-xenial for Pine64s? Linux pine54 3.10.104-pine64 #2 SMP PREEMPT Thu Feb 23 22:26:21 CET 2017 aarch64 aarch64 aarch64 GNU/Linux root@pine54:~# mkfs.btrfs /dev/sda1 btrfs-progs v4.4 See http://btrfs.wiki.kernel.org for more information. failed to open /dev/btrfs-control skipping device registration: No such file or directory Label: (null) UUID: d8362fb9-1b9c-4d92-8222-6745f842efcf Node size: 16384 Sector size: 4096 Filesystem size: 7.04GiB Block group profiles: Data: single 8.00MiB Metadata: DUP 368.62MiB Sys…

• 1

  Reputation Points

• 1 reply
• 3.2k views
• 1 follower

zador.blood.stained

March 28, 20179 yr

As I said in another topic, I'm trying to make bluetooth work with my Pine64 1GB board The other topic is there : Yesterday I tried using `rtk_hciattach` from https://github.com/lwfinger/rtl8723bs_bt That was the program I was using with legacy kernel. After a fresh start (removed the Power USB and plugged it back in) I get this output : root@pine64:~/src/rtl8723bs_bt# ./rtk_hciattach -n -s 115200 /dev/ttyS1 rtk_h5 Realtek Bluetooth init uart with init speed:115200, final_speed:115200, type:HCI UART H5 Realtek Bluetooth :Realtek hciattach version 2.5 Realtek Bluetooth :3-wire sync pattern resend : 1, len: 8 Realtek B…

• 0

  Reputation Points

• 1 reply
• 3.6k views

vlad59

December 13, 20187 yr

Does anyone know where i can find linux headers for the LTS/Sopine, or an image that contains them? None of the images from the wiki seem contain the headers. I installed the Armbian legacy with 3.10.107 and was able to get Pine64 headers using apt-get install linux-headers-pine64 but they seem to be missing many files when i try to compile. Any help is greatly appreciated.

• 0

  Reputation Points

• 1 reply
• 3k views
• 1 follower

obrienmd

June 21, 20188 yr

After installing the latest update, my 3D printer warns about outdated instructions in the MCU and asks to recompile and flash it. What should I do?

• 0

  Reputation Points

• 1 reply
• 2.1k views

mattjm

June 3Jun 3

Hello, I want to monitor the temperature of my Pine64, because I run the pine in an relatively warm environment. Unfortunately, the usual ways do not lead to a reasonable result: I tried the armbianmonitor: "armbianmonitor -m" with this result: Time CPU n/a load %cpu %sys %usr %nice %io %irq CPU 17:08:20: --- 0.00 0% 0% 0% 0% 0% 0% -13552°C 17:08:25: --- 0.00 0% 0% 0% 0% 0% 0% -13673°C and read the file: /sys/devices/virtual/thermal/thermal_zone0/temp: contains the same wrong value -13552 Is there a way to activate the temperature measurement? I am using th…

• 0

  Reputation Points

• 1 reply
• 4.6k views
• 1 follower

Igor

February 6, 20197 yr

Hi, Since I still couldn't find a enclosure for my Pine64 H64 model-B, I mocked up one myself using a Eur 6,50 Raspberry Pi 4 case. 1) From the USB/ETH connector side I cut out the sections in between the connectors since there is a small offset that pushes the Pine64 board aside when closing the case. 2) From one of the cover lulls, I cut out a section to fit over the IR sensor. 3) On the HDMI side I cut out the two ports holes of the RPI micro hdmi connections and I made a notch in the USB-C hole to fit the power connector of the Pine64. 4) Drilled a hole in the cover large enough for the WIFI/BT antenna connector, on the board,…

• 0

  Reputation Points

• 1 reply
• 3.3k views

jeanrhum

April 26, 20206 yr

Hi, Thank you all for so much work to fully implement the mainline kernel for the Pine64! So much is now working out-of-the-box with armbian, that there is no need to use the legacy version based on kernel 3.10. The pine64 does have CIR capabilities and the sunxi-cir kernel module is available, but we are still missing DT bindings for the device, although I see that an overlay file is present for the h5: /dts-v1/; / { compatible = "allwinner,sun50i-h5"; fragment@0 { target = <0xffffffff>; __overlay__ { pinctrl-names = "default"; …

• 0

  Reputation Points

• 1 reply
• 2.8k views

Learnincurve

December 17, 20205 yr

I cannot receive data on serial port ttyS5. I able to write onto it, but the reading doesnt work. I'm using this https://github.com/officialdoniald/Xamarin.Android.SerialPort . I tried using adb shell commands like "cat < /dev/ttyS5" but there is no received data either. When I try to send data with "LibSerialPort.WriteLine("text")" I can see it in Hercules Terminal so the writing works. In Visual Studio Output there is this line: [c.SerialPortPoc] type=1400 audit(0.0:532): avc: denied { read write } for name="ttyS5" dev="tmpfs" ino=2487 scontext=u:r:untrusted_app_27:s0:c512,c768 tcontext=u:object_r:serial_device:s0 tclass=chr_file permissive=1 app=SerialPortPoc.Ser…

• 0

  Reputation Points

• 1 reply
• 4.1k views
• 1 follower

Werner

September 8, 20224 yr

I'm trying to install armbian to the attached emmc with armbian-config. However i get the message "There are no targets, please check your drive". With fdisk -l the emmc doesn't show up. I do know the emmc is working properly because pull out the sd card (after shutting down) and reattach the power it boots from the emmc into android. Does anyone know to fix this? Systeminfo: http://ix.io/1q2B

• 0

  Reputation Points

• 1 reply
• 3.2k views

Igor

October 26, 20187 yr

I have an OrangePi Zero 2 with the latest bullseye (5.19). I would like to activate SPI (and i2c) and was in armbian-config to do so. Besides that the system was frozen, i couldn't see anything under the hardware tab even after defreeze (only empty entries and a short pop-up: "usage: grep....." like in https://github.com/armbian/config/issues/33). While researching the problem, I found out that this could be due to the missing "overlay_prefix" in armbianEnv.txt. So i looked and found sun50i-h616-orangepi-zero2.dts in a subfolder and wanted to enter overlay_prefix=sun50i-h616. Now i get the following error message in the hardware tab: "loading error: expected at…

• 0

  Reputation Points

• 1 reply
• 6.4k views
• 1 follower

cabanak

November 20, 20223 yr

Hello, I am using Allwinner A64 processor for my use case. In that, I want to flash my custom os into emmc memory which is alredy worked in SD card. Currenlty we go thorugh below link: https://wiki.pine64.org/index.php/NOOB#Instructions_to_Flashing_eMMC_Modules we follow "xzcat imagename.img.xz | sudo dd of=/dev/mmcblk1 bs=1M status=progress conv=fsync" this command but we got input/out error while reading memory. Please check below screenshot.

• 0

  Reputation Points

• 1 reply
• 3k views

Werner

October 5, 20215 yr

Hi all, I’m trying to get KlipperScreen running directly on the framebuffer on a BigTreeTech CB1 that’s using an Allwinner H616B chip. It’s running Armbian Bookworm (kernel 6.6.66-vendor-sunxi64, Dec 2024 build) on a Manta M8P V2.0 board with a TFT35-SPI display that shows up as fb_st7796s. The goal is to have KlipperScreen render directly to /dev/fb0 without needing a desktop or HDMI. The framebuffer itself seems fine as the screen shows the BigTreeTech logo on boot, and I can write to it manually, so the driver appears to be working correctly. KlipperScreen installs fine, the Python environment and dependencies are all in place, but when I launch it, I always ge…

• 0

  Reputation Points

• 1 reply
• 3.3k views

JohnTheCoolingFan

October 25, 2025Oct 25

Hello, I downloaded the latest 20.04 image for Pine64+ and I am not getting any audio from youtube for example. I can see in the Volume Control window in the Output panel an audio level meter moving and the application Chromium. But still get no audio from the TV.

• 0

  Reputation Points

• 1 reply
• 2.4k views

Pander

April 22, 20233 yr

So, I've installed Armbian_23.02.2_Orangepizero2_bullseye_legacy_4.9.318.img on 2 diferent SD cards with same results, I'm not able to figure why they don't run fstab, cron jobs or any other script automatically. I'm mounting a samba share, by command it mounts correctly, this is my fstab entry: //192.168.1.2/Descargas /mnt/Descargas/ cifs uid=1000,gid=1000,guest 0 0 tried _netdev to wait for network and then mount with the same results //192.168.1.2/Descargas /mnt/Descargas/ cifs uid=1000,gid=1000,guest, _netdev 0 0 If I run mount -a it works, tried to add it into root crontab with * * * * /bin/mount -a Still, no resu…

• 0

  Reputation Points

• 1 reply
• 4.9k views
• 1 follower

b2522

September 6, 20233 yr

In short, I'm trying to build a FULLY-PREEMPT-REALTIME system to run on my Orange Pi Zero 2W. I used this post as a reference, and got quite far. But, I'm stuck on something that I believe I undestand, but don't know how to resolve. I don't believe this is a probleme specific to my board though. What I've done so far with success is both install and run a pre-built Armbian Image on this board, as well as build my own image and run it. Both work perfectly. Now, I'm attempting to apply the RT patch and build a fresh image (or even just a Kernel) to get the FULL REALTIME kernel support working. However, the build sy…

• 0

  Reputation Points

• 1 reply
• 4.4k views

Skidd

December 31, 20241 yr

Image used: Armbian_21.08.1_Orangepizero2_focal_edge_5.13.12.img U-Boot SPL 2021.10-rc1-armbian (Aug 08 2021 - 16:21:36 +0200) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.5(debug):87311b4-dirty NOTICE: BL31: Built : 16:21:30, Aug 8 2021 NOTICE: BL31: Detected Allwinner H616 SoC (1823) NOTICE: BL31: Found U-Boot DTB at 0x4a082220, model: OrangePi Zero2 INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP305 on RSB INFO: PMIC: aldo1 voltage: 3.300V INFO: PMIC: aldo2 voltage: 3.300V INFO: PMIC: aldo3 voltage: 3.300V INFO: PMIC: bldo1 voltage: 1.800V INFO: PMIC: dcdcd voltage: 1.500V IN…

• 0

  Reputation Points

• 1 reply
• 4.9k views

izeroo

November 22, 20214 yr

Hi, I brought new pine64 board and installing OS in SD card. This OS considering kernel 5.10.34 and now I want to modify some of the kernel features. For that, please guide me how to download kernel source and rebuild it for pine64.

• 0

  Reputation Points

• 1 reply
• 2.9k views

Werner

June 5, 20215 yr

Hi all, I've read on the forum that support for usb gadget using the µ-usb port on the libre computer tritium needed a kernel reconfigure & recompile. I tried to start with that, but during configuration, I've seen full support already. So, was it supposed to just work ? I target armbian buster server variant. my need is to use IP over an usb (and power) cable between a linux machine (x86 and then arm) and a tritium h5 Thanks in advance

• 0

  Reputation Points

• 1 reply
• 3.6k views
• 1 follower

TRS-80

December 17, 20205 yr

I am trying to configure a splashscreen in u-boot on an orange pi zero plus using Armbian. The screen is connected through spi1 using the ST7789v chip of the LCD. I have successfully configured the screen when the kernel is loaded. I already have used systemd to display a splashscreen however I find it slow to display something. It display something only after ~12 sec. I could probably reduce that time a bit by loading the service earlier but it would never start in 5 sec. I have tried unsuccessfully to activate CONFIG_VIDEO_LCD_MODE (VIDEO_LCD_MODE) in u-boot which allow to configure an LCD. It seems that it is not allowed because it d…

• 0

  Reputation Points

• 1 reply
• 4k views

tipine9824

November 25, 20223 yr

Let me think about how to descript this situation...... I have a movable disk and mount in path: /mnt/sba1 It happened first time when I using a program called "Syncthing" , I try to sync my file into my movable disk. I get lot of files in my directory. When the "Syncthing" start scanning. the system will stuck. Not that kind of whole system stuck, but only if you trying to read anything about /mnt/sda1. If you trying to "df -h", you'll get stuck. "fdisk -l", stuck. "cd /mnt/sba1", stuck again. "mount" "umount" "lsblk" all will be stuck. Such like this ...... Reboot the system is only way to restore.…

• 0

  Reputation Points

• 1 reply
• 2.9k views

TheOWL

June 8, 20233 yr

Hello everyone, I am using an Orange Pi Zero 2W with a graphical user interface (GUI). I downloaded and installed the official Orange Pi Zero 2W image. Unfortunately, I keep running into a Wi-Fi connection issue. After booting, the system repeatedly asks me to enter my Wi-Fi password. If I don’t enter it, I have no internet connection. What’s interesting is: If I disable and re-enable Wi-Fi in the network manager, it automatically reconnects to the known network without asking for the password again. Alternatively, a system reboot also restores the Wi-Fi connection automatically. I have already seen o…

• 0

  Reputation Points

• 1 reply
• 1.9k views
• 1 follower

Werner

January 5Jan 5

I tried to install armbianmonitor on the opi zero 2, but unfortunately this fails: orangepizero2:~$ sudo armbianmonitor -r Installing RPi-Monitor. This can take up to 5 minutes. Be patient pleaseE: Unable to locate package rpimonitor /usr/bin/armbianmonitor: line 697: /usr/share/rpimonitor/scripts/updatePackagesStatus.pl: No such file or directory /usr/bin/armbianmonitor: line 193: /etc/rpimonitor/template/raspbian.conf: No such file or directory /usr/bin/armbianmonitor: line 196: cd: /etc/rpimonitor/: No such file or directory sed: can't read /etc/rpimonitor/template/temperature.conf: No such file or directory sed: can't read /etc/rpimonitor/template/cpu.conf: No such…

• 0

  Reputation Points

• 1 reply
• 4k views

nopnop2002

March 5, 20242 yr

This is an old, original Pine64 Board w/ 1GB RAM. Armbian Version: 5.69 I am unable to get audio signal (output) from the Audio Jack. Tried normal headphone with 3 contacts, also tried headset with 4 contacts, BOTH fail to get audio out. Tried Stretch and also Ubuntu, no success... Does anybody succeed getting audio out from the onboard audio jack with Armbiam? If so, can you give a brief description of the procedure/steps and the soft(s) you are using? When using a external USB Audio adapter everything seems to work fine (connecting to the Adapter Audio Jack), so, I guess that from the point of view of…

• 0

  Reputation Points

• 1 reply
• 3.6k views
• 1 follower

ecolezen

January 22, 20197 yr

Hi there! How to disable private ethernet MAC on OPZ2? Router says my device has one.

• 0

  Reputation Points

• 1 reply
• 2.6k views
• 1 follower

Hans.K.K.

January 27, 20233 yr

This is only my perception. I have this three SBC.: PINE 64 +, Nano PI A64, Banana pi M64. Everything on A64 allwinner chip. Armbian Image for Pine 64 works both Pine and Bananapi M64. But does not work NANO PI A64. Other third party software ( systems ) Remix, Ubuntu, work pine and banana pi and dont work nano pi. Only android 5.1.1 works on these three SBC....

• 0

  Reputation Points

• 1 reply
• 2.6k views

zador.blood.stained

April 11, 20179 yr

Hi everyone, I'm struggling to get gpio_keys working. I'm trying to use the overlay, which I have attached below, but after reboot there is no event node listed in "/dev/input/". (There is only one node named mice.) Inspecting dmesg, I found the following error messages: [ 1.529891] sun50i-h616-pinctrl 300b000.pinctrl: pin PC8 already requested by gpio-keys-user; cannot claim for 300b000.pinctrl:72 [ 1.529917] gpio-keys gpio-keys-user: failed to get gpio: -22 [ 1.529926] gpio-keys: probe of gpio-keys-user failed with error -22 Inspecting the dts file of my board (orange pi zero 2), I found that PC5,PC6 and PC8 are…

• 0

  Reputation Points

• 1 reply
• 4.2k views
• 2 followers

ValdikSS

January 10, 20251 yr

i have a alfa awus036acm wireless adapter install on my orange pi one with armbian jammy installed. my awus036acm adapter is not recognised , when i type iwconfig it's say no wireless extension is there possible way to make it work?

• 0

  Reputation Points

• 1 reply
• 2.9k views

Igor

December 16, 20223 yr

Hi, i'm new with linux and SBC. My final goal is to use the board as a voice command recognition system (without display) and to be honest i do not know how to start. I downloaded Armbian desktop on microSD using balenaEtcher and I inserted it in the board e powered it! i do not have a display unfortunatly and i do not know if desktop version is the best choice or i have to install an embedded version if exists. Could help please? thanks

• 1

  Reputation Points

• 1 reply
• 3.9k views
• 1 follower

Werner

October 4, 20224 yr

boot0 version : 4.0.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 DRAM driver version: V1.1 rsb_send_initseq: rsb clk 400Khz -> 3Mhz Set DRAM_VCC failed initializing SDRAM Fail. HELLO! BOOT0 is starting! boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f

• 0

  Reputation Points

• 1 reply
• 2.1k views

pfeerick

June 22, 20179 yr

Hi, I have a Pine64-1gb laying around collecting dust for more that a year and had the idea to replace my RPi3 whitch is now running as a VPN Router. The RPi3 is restricted to 2 streams and cause cpu load to 100% so mabe the Pine64 could help here. As I already setup the RPi3 as VPN Router I thought I use the same procedure for the Pine64 with Armbian Jessie. This is what I use: HW: Pine64 with 1gb ram (Model: PA641GB) OS: ARMBIAN 5.38 stable Debian GNU/Linux 8 (jessie) 3.10.107-pine64 VPN software: OpenVPN VPN Service: PIA Here a small tutorial of the commands that I'v been used to create this VPN Gateway:…

• 0

  Reputation Points

• 1 reply
• 5.7k views
• 2 followers

gounthar

March 29, 20197 yr

I am looking for support library for GPIO, SPi for Orange pi zero2 H616. I searched everywhere but found only 1 library https://github.com/orangepi-xunlong/wiringOP. I tested by flashing one led but stopped like the GPIO pins are the same? I don't know what's going on here? Is there a library to support me?

• 0

  Reputation Points

• 1 reply
• 3.9k views
• 1 follower

Werner

January 22, 20215 yr

WiFi isn't working on the current legacy image: Armbian_22.11.3_Orangepizero2_jammy_legacy_4.9.318.img [FAILED] Failed to start Access poi…server for Wi-Fi and Ethernet. See 'systemctl status hostapd.service' for details. [ OK ] Finished OpenVPN service. openvpn.service [ OK ] Started /etc/rc.local Compatibility. rc-local.service rpc-statd-notify.service [ OK ] Started Notify NFS peers of a restart. [ OK ] Finished Permit User Sessions. systemd-user-sessions.service [ OK ] Started Bluetooth service. bluetooth.service [ OK ] Reached target Bluetooth Support. Starting Hold until boot process finishes up... Starting Terminate Plymouth …

• 0

  Reputation Points

• 1 reply
• 4.2k views

gyrex

February 24, 20233 yr

Hello, I am looking for a specific legacy image for the Orange Pi Zero 2W: Armbian 23.02.2 Bullseye with Kernel 5.10.160. The reason I need this specific version is to use the device as a USB UVC (Webcam) gadget via ConfigFS. On the newer 6.6/6.12 mainline kernels, I am facing a "Permission Denied" error when trying to write to hHeight, even as root. After researching, it seems this is a known kernel-level restriction in newer versions, and the legacy 5.10 kernel is the most stable for UVC gadget functionality. I’ve checked the current archive mirrors but could only find the 6.6.x versions. Could anyone provide an official archive or a reliable mirror link …

• 0

  Reputation Points

• 1 reply
• 2.6k views

Werner

December 20, 2025Dec 20

How can I keep the LTS-kernel (4.14) with a terminal command? The lastest update/upgrade installs the kernel 4.17. How can I avoid this kernel-update? For my long term-project I need the LTS-kernel 4.14. Some time ago I updated by mainline-system (Ubuntu server kernel 4.13 to 4.14-kernel with the following command apt-get -y -qq --no-install-recommends install linux-image-next-sunxi64 linux-headers-next-sunxi64 linux-u-boot-pine64-next linux-xenial-root-next-pine64 linux-dtb-next-sunxi64 Thanks a lot.

• 0

  Reputation Points

• 1 reply
• 3.5k views

Igor

July 6, 20188 yr

Are there any plans of creating an image incorporating an mainline 4.xxx kernel for the pine64 boards? Kernel.org states the projected EOL for the 3.10 kernel line as october 2017.

• 0

  Reputation Points

• 1 reply
• 2.6k views

Igor

April 19, 20179 yr

Running Armbian Ubuntu Xenial 16.04 on a PineA64, legacy kernel 3.10.105-pine64. Why is it necessary or desirable to put the variable 'ethaddr' in armbianEnv.txt? I thought the hardware mac address would be detected by the kernel. Perhaps not?

• 0

  Reputation Points

• 1 reply
• 2.7k views

Andro

September 8, 20179 yr

I need to use a 10 inch 800x600 DSI display in a Pine64 project and I think the easiest way to do this would be to modify the driver for the Pine 7 inch DSI display. It appears to me that the display resolution is hard coded in this driver (panel-feiyang-07024di26a30d.ko) and not supplied by a device tree overlay like some other Armbian SBCs. In the C source for this driver, I see the following data structure which defines a 1024x600 screen size for the 7 inch display ... static const struct drm_display_mode feiyang_default_mode = { .clock = 55000, .hdisplay = 1024, .hsync_start = 1024 + 310, .hsync_end = 1024 + 310 +…

• 0

  Reputation Points

• 1 reply
• 2.8k views

DasFisch

January 21, 20251 yr

I have been running Armbian on a headless Pine64 (the kickstarter one) for quite sometime without any issues. Last week I woke up in the morning and noticed that there had been a power cut. The Pine64 was on again but I couldn't SSH into it. I plugged a monitor and found the system hangs while booting with the following error: Error while loading shared libraries: lib system-shares-241.so: cannot open shared object file: No such file or directory Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00 CPU: 1 PID: 1 Comm: init Not tainted 5.4.43-sunxi64 #20.05.2 Hardware name: Pine64+ (DT) Call trace: dump_backtrace+0x0/0x180 show_stack+0x14/0x20 dump_s…

• 0

  Reputation Points

• 1 reply
• 2.8k views

Igor

December 29, 20205 yr

I have been trying to get DS3231 to work with the OrangePi Zero 2 via the i2c bus. I have tried setting the following settings in /boot/armbianEnv.txt overlay_prefix=sun8i-h6 overlay=i2c0 i2c1 i2c2 However, I am not able to use i2c tools to read the DS3231. Any suggestions are welcomed. Thank you in advance!

• 0

  Reputation Points

• 1 reply
• 5.2k views

serg_stetsuk

January 7, 20242 yr

An extravagant man of boundless vision-part Raymond Loewy, component Buckminster Fuller, component Willy Wonka, and a smidgen Pepe Le Pew-Philippe Starck is nominally a industrial designer however truly an almost-anything-you-can-think-of designer. >> https://www.facebook.com/Bestmasticatingjuicers.zones He became famous in the 1980s and 90s because of his prong-like toothbrushes and citrus-juicers for Alessi, his sculptural chairs for Kartell, and his revolutionary interiors for Ian Schrager's first creation of boutique resorts, one of them New York's Royalton along with Miami Beach's Delano. Since then, his interests have ranged wider still, from his Sta…

• 0

  Reputation Points

• 1 reply
• 3.3k views
• 1 follower

Igor

June 7, 20188 yr

I have OPIZ2 been running for months for node-red and MQTTbroker. Due to crappy configuration I did during the insallation, then I decided to replace the OS and reconfigure all, I used the same SDcard and reflash with same Armbian_23.5.2_Orangepizero_jammy_current_6.1.30. But, beyond this point, OPIZ2 never boots anymore... I tried other armbian version and it is the same dead. If I use a fresh SD card (Sandisk 16GB A1) then it works ok. My question is regarding the SD card imaging ( i am using Balena-etcher), is there something change inside the SDcard after reflash so that OPI does not recognise the booting part anymore??

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Werner

July 9, 20233 yr

Hello, Ive setup ssh and did some stuff on my OrangePi, when i came back and plugged my phone into power hub my OrangePi was connected to, it restarted and stopped at disk manager, i restarted it and it gave lots of failed messages, i restarted and it didnt work anymore :( it only gives yellow ethernet led and nothing else, i also reflashed sd card because it got all partitions gone after that incident Please help!!!

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

Werner

December 17, 20241 yr

I'm running Octoprint on Orange Pi Zero 2 and Armbian 22.11.3 Bullseye with Linux 4.9.318-sun50iw9 (other than assorted added userspace software, it's stock Armbian, no recompiled kernel or anything like that). It works great - while it works. I successfully complete 30+-hour prints. I can connect, monitor, everything is fine and dandy. When I'm connected to Octoprint from PC, monitoring of the 3D printer enabled, even without printing anything, it works ok. But if I'm not connected, and the printer is doing nothing for a prolonged time (an hour or so?), it stops working. Probably goes to sleep - stops responding to any network communication. Since it's a fully headless s…

• 0

  Reputation Points

• 1 reply
• 3.1k views

Werner

September 1, 20233 yr

I have Armbian up and running very nicely on the PineA64+ 2GB board. Thanks to the community! Speed concerns aside, is it possible to attach a SATA drive to this board? What would be the recommended way to do so? It is the availability of large storage capacity that we need for our project, not blazingly fast disk writes.

• 1

  Reputation Points

• 1 reply
• 3k views
• 1 follower

Igor

August 5, 20179 yr

Hi, on latest Armbian 23.11.1 Bookworm with PINE64 board I noticed those warnings in journal: Feb 12 10:00:45 pine64 systemd[1]: /lib/systemd/system/systemd-journal-upload.service:33: Unknown key name 'RestartSteps' in s> Feb 12 10:00:45 pine64 systemd[1]: /lib/systemd/system/systemd-journal-upload.service:34: Unknown key name 'RestartMaxDelaySec> I suspect the `systemd-journal-upload.service` is not in tact with systemd daemon version installed.

• 0

  Reputation Points

• 0 replies
• 2.2k views

cvxx

February 12, 20242 yr

Hi, Can anyone tell me how can i remove the wifi and ethernet services completely from the armbian.

• 0

  Reputation Points

• 0 replies
• 2k views

kapil

June 8, 20233 yr

Hello, I have two Orange Pi Zero 2 for two years, I didn't know what to do with it. Yesterday I have installed Armbian_25.5.1_Orangepizero2_noble_current_6.12.23. The serial was a bit buggy during installation (display + key press), I have used option -L with screen: screen -L /dev/ttyUSB0 115200 Thank you for your great work !

• 0

  Reputation Points

• 0 replies
• 1.5k views
• 1 follower

Jodaille

October 7, 20251 yr

Hey folks, I have a really weird issue where any time I try to `cat` any of the cpufreq files or use any of the cpufreq commands, it just hangs indefinitely. I've made sure that everything is up to date, reinstalled cpufreq, and because I have 2 of the same board, have confirmed that it's an issue with both of my Zero 2s. I also ran `strace` on one of the cpufreq commands and found that it's getting hung on a write step: openat(AT_FDCWD, "/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor", O_WRONLY) = 3 write(3, "ondemand", 8 Other than this, the device has been doing just fine. Any advice on this is welcome! OrangePi Zero2 Armbian (24.11.1) aarch6…

• 0

  Reputation Points

• 0 replies
• 1.8k views
• 1 follower

SubspaceEmissary

January 7, 20251 yr

Hi, When will soon be ready for the Armbian Pine A64 Desktop Debian? Can I now install Debian xfce on the Armbian Pine A64 Server? and how? Thank you

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

Hannover

November 7, 20169 yr

I have looked up relevant information on Google. Since 5.6, pine a64 already supports dsi in the kernel mainline.And the Feiyang FY07024DI26A30-D 7inch MIPI-DSI LCD Panel driver and dts already released. But the 7inch lcd above is a video mode panel.I can not found any information about the command mode panel. Is pine a64 mipi-dsi supports command mode from the kernel mainline? Any help is appreciated!!

• 0

  Reputation Points

• 0 replies
• 2.6k views

jam

May 26, 20215 yr

Hello all you awesome community members! So I got this Pine a64+ during their Kickstarter campaign. Initially I used it as a little play desktop. I never really found a use for it until very recently. I decided to use it as a little software Squeezebox client. I installed Armbian 22.04 server. I then setup alsa to use the HDMI audio as default output. I installed squeezelite and it immediately found and connected to my LMS (Logitech Media Server) running on my server. At this point I figured all was good. The sound was working great through my receiver. The next morning (Sunday) the kids could not get the TV sound to work. So of course …

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

BJWTech

July 25, 20224 yr

After a fresh armbian installation + armbian-firmware-full package, the pine64 bluetooth doesn't work because the rtl8723bs_config-pine64.bin file is missing. I've downloaded the file from https://github.com/anarsoul/rtl8723bt-firmware/tree/master/rtl_bt into /lib/firmware/rtl_bt and it works so I've created a PR here https://github.com/armbian/firmware/pull/14 to add it to the firmware package so it can work out of the box. Let me know if I need to do something else for the PR to be merged. Thanks.

• 0

  Reputation Points

• 0 replies
• 2.7k views
• 1 follower

eminguez

April 28, 20206 yr

Hello, i'm succesfull using an armbian image from a long time. Now i compile a new image with the dev kernel (linux-sunxi right?). The problem is that, if i boot the new image the system hangs here: Spoiler U-Boot SPL 2017.11-armbian (Apr 12 2018 - 15:09:59) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000) NOTICE: Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):c9f55c0 NOTICE: BL3-1: Built : 15:09:28, Apr 12 2018 NOTICE: DT: sun50i-a64-pine64-plus INFO: Configuring AXP PMIC NOTICE: PMIC: fixing DRAM voltage from 1.24V to 1.36V INFO: PMIC:…

• 0

  Reputation Points

• 0 replies
• 1.9k views

DuDu371

April 12, 20188 yr

I'm currently looking into a new project which will use (hopefully) the Rpi Waveshare hdmi based 4" lcd touch screen, linked to the pine64/Sopine I'm at research stage, and will be looking into using a current 5.x kernel. If anyone has any info on the waveshare lcd's I need to watch out for or suggestions to get further info (specifically the touch driver side), please post a response. Progress on the project will be posted here, links will be added once I have some basics running. This can hopefully open up the waveshare displays to other devices. @Igor Yes I've read This post but am willing to do what I can to get Armbian to support the d…

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

Gavinb

January 27, 20206 yr

My Pine64 boots using Armbian_5.30_Pine64_Ubuntu_xenial_default_3.10.105_desktop. I have added pine64_lcd=on to /boot/armbianEnv.txt and updated the module file. But now when I plug in HDMI nothing displays on the HDMI screen. I also can not see it as a secondary display. Is it possible to have both displays on or can I only have one, having to remove LCD if I want HDMI output?

• 0

  Reputation Points

• 0 replies
• 2.7k views

Zululander

August 14, 20179 yr

Hi!I am trying to connect B101UAN01.7 display(1920 x 1200) without any success.Is pine64's driver supports other display than native 7"? If so, then could you please help me to understand where can be error?Here is cutout from my device tree for 10.1" display lcd0@01c0c000 { compatible = "allwinner,sunxi-lcd0"; pinctrl-names = "active", "sleep"; status = "okay"; device_type = "lcd0"; lcd_used = <0x0>; lcd_driver_name = "mb709_mipi"; lcd_backlight = <0x32>; lcd_if …

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

vicb

June 1, 20179 yr

What version of armbian is the best overall for the opiz2 ? im mainly going to use it as a server so no desktop.its gonna run some python code for my bots. i might move it around so wifi with 5ghz support is a must .

• 0

  Reputation Points

• 0 replies
• 2.8k views

hardcod3dd

December 7, 20223 yr

Armbianconfig on OrangePi Win shows dev and next kernel branches to switch to. When selecting next for instance the following packages would be installed: linux-image-next-pine64 linux-headers-next-pine64 linux-u-boot-orangepiwin-next linux-xenial-root-next-orangepiwin The image and headers dpkgs are not present in the repo (http://apt.armbian.com/pool/main/l/) though, so update fails. The suggested kernel image from https://www.armbian.com/kernel/ (linux-image-dev-sun50iw2) is also not present. Even the installed kernel (linux-image-pine64) is not present in this repository So i'm confused. Am I looking at…

• 0

  Reputation Points

• 0 replies
• 1.7k views

xnyle

April 15, 20188 yr

Everything come from a try to create a docker compose project. Armbian 24.8.4 bookworm on OrangePI zero 2 - Network forwarding doesn't work: ``` version: '3.6' services: db: image: mariadb:10.3 environment: MYSQL_ROOT_PASSWORD: secret phpmyadmin: image: phpmyadmin restart: always ports: - 8080:80 environment: - PMA_HOSTS=db ``` => FROM test-db-1 => test-db-1 3306 ``` docker exec -ti test-db-1 bash -c 'timeout 0.5 echo -n 2>/dev/null < /dev/tcp/test-db-1/3306 && echo "open" || echo "closed"' ----------- open ----------- ``` => FROM test-phpmyadmin-1 =…

• 0

  Reputation Points

• 0 replies
• 2.3k views

Jeremy Levy

November 7, 20241 yr

What's the current status of 5.30 on Pine64 mainline? I've a spare Pine64 lying around and was considering compiling latest Armbian for it to poke around a little, test things if that's useful to the dev effort. The downloads page lists support as experimental, but the version there is 5.27 and some of the info seems out of date, ie points to the wrong subforum, etc.

• 0

  Reputation Points

• 0 replies
• 2.2k views

reverend_t

August 21, 20179 yr

I set up a new Banana Pi M4 Zero, with an HDMI monitor that had previously been used with a Raspberry Pi, a USB hub with a keyboard and mouse. I downloaded the Armbian Ubuntu Jammy desktop, the activity light flashed a bit but no video. I soldered a header to the debug serial pads and connected to a PC through a serial to USB converter. Using that link I could see the boot process, and communicate. I used armbian-config to set up wifi etc, but still no video. I have tried Jammy minimum, and both Debian downloads but still no video. There appears to be nothing coming across the HDMI connection, the monitor detects that there is a physical connection but no video. The same …

• 0

  Reputation Points

• 0 replies
• 2.1k views

keithr

September 21, 20242 yr

Armbian 22.11 Bullseye / Jammy Kernel 4.9.318 or 6.1.4 Release date: Jan 10, 2023 Legacy kernel has more or less full hardware support, while mainline lack functions such is wireless, HDMI, ... https://www.armbian.com/orange-pi-zero-2/ Looking for maintainer!

• 0

  Reputation Points

• 0 replies
• 7.3k views
• 1 follower

Igor

January 10, 20233 yr

I recently upgraded my working Pine A64-LTS board to Armbian 10.9 by using standard 'apt-get update' followed by 'apt-get upgrade' The update went fine (no error messages) and i rebooted the unit. The unit was unable to mount the root filesystem it complaint about UUID probably incorrect, but this was not the case. After doing some research i found out that the DTB file was changed on the mmc0 part. The option 'non-removable' was removed wich let to the kernel using the PUSH-PUSH routine? cd pins to see if a SD card is present. It looks like it that not all versions of the Pine A64-LTS have this pin or maybe in the past …

• 0

  Reputation Points

• 0 replies
• 6.6k views
• 1 follower

Patrick Peters

May 5, 20215 yr

Hello, I have a Pine64 board and recently added an audio POT with the pcm5102a chipset. It is rather difficult to get the board working/recognized. I found info on the forum saying one has to do stuff with the overlay system but only for other boards than the Pine64 and I can't get it right. aplay -l: root@pine64:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sun50ia64audio [sun50i-a64-audio], device 0: 1c22c00.dai-sun8i-codec-aif1 sun8i-codec-aif1-0 [1c22c00.dai-sun8i-codec-aif1 sun8i-codec-aif1-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sun50ia64hdmi [sun50i-a64-hdmi], device 0: 1c22800.i2s-i2s-hifi i2s-hifi-0 [1c…

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

joho500

November 20, 20214 yr

pine 64so Pine64, bananapi M64 images 19.11.3, GUI XFCE 4.12 dont not run after upgrade images 20.02 GUI does not work from begining after installed. Never mind i build 19.11.5 kernel 5.4.18 and works

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

constantius

April 11, 20206 yr

I cannot boot into lvm encyprypted root partition: mount: mounting "/dev/mapper/vg-root on /root failed: No such file or directory␍␊ Failed to mount "/dev/mapper/vg-root as root file system.␍␊ The flollowing step i made (short version) - create the lvm partition - mount lvm partition and and copy file system auf lvm partition, bind /dev, sys, proc - chroot in the lvm root partition (vg-root) - change /etc/fstab : insert /dev/mapper/vg-root / ext4 errors=remount-ro 0 1 UUID=<UUID-Partiion> /mnt/mnt ext4 defaults,noatime,nodiratime,commit=600,errors=remount-ro …

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

linda

July 29, 20224 yr

I am new to this whole endeavor and I am attempting to SD-cardless boot my orange pi zero 2 and after nearly a week of playing around have it nearly working. I have custom compiled Armbian 23.08.0-trunk with Bookworm and 6.2.16 kernel with ROOTNFS set to Y I have unpacked rootfs to my NFS server I have setup PXE booting via pxelinux.cfg/01-<mac address> I have u-boot working from SD Card ( It technically works from SPI but gives temperature error every boot of kernel) I can boot all the way into a functioning OS. My problem is that while PXE booting allows for loading overlays, I cannot load a fixup.scr or similar via PXE from what I can tell. I have …

• 0

  Reputation Points

• 0 replies
• 2.6k views

Whinis

May 28, 20233 yr

Hi How do I change the DSI clock for Pine A64-LTS ? Thank you.

• 0

  Reputation Points

• 0 replies
• 2.2k views

RyoTanaka

October 31, 20187 yr

Hi, just want share a little experiment I am doing to try to solve my Pine64 Boot Crash/Freeze Problem using a external (MCU) microcontroller to assist it. [MCU and Pine Drawing] [Actual Prototype Photo] The idea is very simple, just "watch" the SystemLED to detect if the system is booting normally, and if NOT, then issue a hardware reset, then, keeping repeating this process until the SystemLED indicates that the system is booting up... I am trying to document the process here is this tutorial page: http://www13.plala.or.jp/pskitty/copineon.html Files, source code, high quality pictures here on GitHub: h…

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

ecolezen

June 18, 20179 yr

I tried to flash the latest Armbian (Armbian_5.52.180715_Pine64_Ubuntu_bionic_dev_4.18.0-rc4) on my A64+. When starting I can't bott and gett one of these error messages: Does anybody have any idea what might go wrong? I know it's not stable yet. After that message, the device waits for an image from a TFTP Server.

• 0

  Reputation Points

• 0 replies
• 3.3k views
• 1 follower

starmagoo

July 31, 20188 yr

On a clean Armbian image (Armbian_23.5.2_Orangepizero2_jammy_legacy_4.9.318.img) I am not able to connect to an AP. nmcli or nmtui produces errors (https://paste.armbian.com/ogowinebol). This also holds for the other jammy_legacy images in the archive. When testing on the stock images provided orange pi I am able to connect with both the Orangepizero2_3.0.6_ubuntu_jammy_server_linux5.16.17.img and Orangepizero2_2.2.0_ubuntu_focal_server_linux4.9.170 images it works. Connecting also works on the Amrbian focal_legacy images I tried.

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

mklomp

August 9, 20233 yr

Is it possible on a Banana Pi M4 Zero to reboot Armbian running from SD card, so that the next time it boots from the internal storage, without removing the SD card? (and without modifying sdcard boot sector) I want to create an automatic backup internal storage - so that the system (booted from emmc) reboots, starts from the SD card, backs up content emmc to sdcard, and then reboots again, booting from emmc. Is it possible some how?

• 0

  Reputation Points

• 0 replies
• 1.2k views

-jk-

May 8May 8

Ciao dears, I hope this is the correct section. I tried to find a solution in this and other forums, but I found dated post . I try to open one with the hope of solving the problem also for others I'm having trouble getting the camera module s5k4ec to work for my pine64 running armbian 5.60 #cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=16.04 DISTRIB_CODENAME=xenial DISTRIB_DESCRIPTION="Ubuntu 16.04.5 LTS" Here my armbianmonitor -u http://ix.io/1wU9. i've activated the module in/boot/armbianEnv.txt verbosity=1 console=both disp_mode=720p60 camera_type=s5k4ec pine64_lcd=off overlay_p…

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

Lendi

December 27, 20187 yr

Hi, I'm actually working on a project with this hardware: IR + controller : https://es.aliexpress.com/item/1005005651928240.html?spm=a2g0o.order_list.order_list_main.5.21a9194dT8Becw&gatewayAdapt=glo2esp MPR121: https://es.aliexpress.com/item/1005005097989944.html?spm=a2g0o.order_list.order_list_main.11.21a9194dT8Becw&gatewayAdapt=glo2esp Bluetooth speaker, but i would use the chip that comes with orange pi . My answer is that i have all of these working inside a raspberrie pi 3 b 1.2, with python to detect the mpr121 pulsations and ir pulsations and manage connection Bluetooth, my problem is that I want to be sure that works, and actually the …

• 0

  Reputation Points

• 0 replies
• 2k views

joitronix

February 16, 20251 yr

Hi, I really apologise if the information is out there and I just haven't found it. I was looking to buy a board for a small embedded GUI application and this one seems to fit the bill. I would like to use Wi-Fi, Bluetooth and HDMI. Is there a list of what is working or not working on each build/version? (This is probably a more general question to Armbian for any device) The only thing I could find is this: But it's not that recent. On the download page: https://www.armbian.com/orange-pi-zero-2/ under specifications it does list, Bluetooth and Wi-Fi but I'm not sure if this means its now working? …

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

av4625

August 28, 20242 yr