Allwinner sunxi

Hello. The BigTreeTech TFT35 SPI works well but has ghost touches. So it's unusable for control tasks like on a 3D printer. It gives random commands to the printer from time to time, which can be dangerous. There is a patch from BigTreeTech since 24-1-2024 https://github.com/bigtreetech/CB1-Kernel/commit/ab7b1fa6ddd7f15ecdc590d32a812589fa38d973 I cannot find it on https://github.com/armbian/build/blob/main/patch/kernel/archive/sunxi-6.6/patches.armbian/add-bigtreetech-cb1-dts.patch and I can confirm that I have this problem with Armbian 24.8.1 Bookworm. But not with BigTreeTech 2.3.4 image. Could someone add these patches to the armbi…

• 0

  Reputation Points

• 1 reply
• 3.5k views

JohnTheCoolingFan

December 17, 20241 yr

So there is some weirdness happening with Armbian on the Orange Pi Zero 2 that I bought from Amazon. These are the V1.5 version of the hardware. With the Orange Pi image (which looks strangely like armbian), once the device is booted, the red led goes off, and the green led turns on. With the armbian image, the red light stays on, and the HDMI output does not turn on in the CLI image. This led me initially to think this board was not working. Once I hooked up a USB to Serial interface, I noticed it booted. Well, at least when the SD card was seated correctly, but that is a hardware problem. Once booted, `armbian-config` does not show the wif…

• 0

  Reputation Points

• 3 replies
• 3.5k views
• 1 follower

ALIGMSTEN

January 10, 20233 yr

How can I keep the LTS-kernel (4.14) with a terminal command? The lastest update/upgrade installs the kernel 4.17. How can I avoid this kernel-update? For my long term-project I need the LTS-kernel 4.14. Some time ago I updated by mainline-system (Ubuntu server kernel 4.13 to 4.14-kernel with the following command apt-get -y -qq --no-install-recommends install linux-image-next-sunxi64 linux-headers-next-sunxi64 linux-u-boot-pine64-next linux-xenial-root-next-pine64 linux-dtb-next-sunxi64 Thanks a lot.

• 0

  Reputation Points

• 1 reply
• 3.5k views

Igor

July 6, 20188 yr

Hi, Is possible to solve problem ? After reboot command orange pi zero 2 not want start and it stay turner off . I read article about changing R_WDOG instead of WDOG in ATF fix for different boad: Thanks

• 0

  Reputation Points

• 1 reply
• 3.5k views

cabanak

November 8, 20223 yr

I'm running Armbian 20.08 Focal on a Pine64 with 2GB RAM. Mostly everything runs fine, but I do have a problem with getting audio out of the headphone plug. In pavucontrol I can see audio is playing (an internet stream) on Built-in Stereo, but nothing can be heard when connecting speakers. To be clear: I don't want audio out of HDMI, but just from the headphone plug. I have also played around with alsamixer and unmuted everything that was muted and turning up the volume, but still no audio to be heard... Has anybody gotten this to work?

• 0

  Reputation Points

• 2 replies
• 3.5k views

Pander

April 22, 20233 yr

Hi, I've tried to change the default console from ttyS0 to ttyS3, using the mainline kernel but I don't get it to work. Modifying boot.cmd I managed to change the tty's baudrate like this: "if test "${console}" = "serial" || test "${console}" = "both"; then setenv consoleargs "${consoleargs} console=ttyS0,38400"; fi" after recompiling with "mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr" it gave me an 38400-baud-output begining with line "Loading, please wait...starting version 229" But changing the settings to use ttyS3 does not work at all: "if test "${console}" = "serial" || test "${conso…

• 1

  Reputation Points

• 4 replies
• 3.4k views

linda

July 9, 20179 yr

problem description as follow: our compile env: root@ubuntu69:/tycom/armbian# uname -a Linux ubuntu69 4.15.0-36-generic #39-Ubuntu SMP Mon Sep 24 16:19:09 UTC 2018 x86_64 x86_64 x86_64 GNU/Linux root@ubuntu69:/tycom/armbian# cat /etc/os-release NAME="Ubuntu" VERSION="18.04.1 LTS (Bionic Beaver)" ID=ubuntu ID_LIKE=debian PRETTY_NAME="Ubuntu 18.04.1 LTS" VERSION_ID="18.04" Board：PINE H64 Compile Env：from https://github.com/armbian In our compile environment，generate the image file：Armbian_5.67_Pineh64_Debian_stretch_dev_4.19.2.img，we burn it into SD by Etcher，the booting is hang，no error message: Starting kernel ... …

• 0

  Reputation Points

• 6 replies
• 3.4k views

Tido

November 29, 20187 yr

Hi everyone, I'm using Pine64 LTS for a project. According to AXP803 datasheet Page37 & 38, the charge LED indicator can be set to Mode A or Mode B. Does anyone know how to change this setting via sysfs, or other interface(I2c, Uart) ? pine@pine64so:/sys/class/power_supply$ ls axp20x-battery axp813-ac pine@pine64so:/sys/class/power_supply$ cd axp813-ac pine@pine64so:/sys/class/power_supply/axp813-ac$ ls device health input_current_limit online power present subsystem type uevent voltage_min pine@pine64so:/sys/class/power_supply/axp813-ac$ cat uevent POWER_SUPPLY_NAME=axp813-ac POWER_SUPPLY_HEALTH=Good POWER_SUPPLY_PRESENT=1 POWER_SU…

• 0

  Reputation Points

• 2 replies
• 3.4k views

Igor

April 20, 20197 yr

Hello, I'm using a Pine 64 LTS with the SoPine image Armbian 21.02.3 Bionic with Linux 5.4.88-sunxi64 I have made various changes and installations to this image, so I want/need to continue using this image. Unfortunately, with the new hardware of the Pine 64 LTS (Pine64 LTS-V2) network connection is no longer possible. (Note: With the current SoPine image there is a network connection). Is there any way to reinstall the current network drivers in my image? I would be very grateful for any help.

• 0

  Reputation Points

• 3 replies
• 3.4k views

Alexander Ressler

April 12, 20233 yr

Hi all, I'm trying to change access my zero 2 via hostname instead of IP (e.g. https://mypizero2.local/). I've changed the hostname through sudo armbian-config but just cannot connect to it via hostname. Has anyone managed to get this working?

• 0

  Reputation Points

• 0 replies
• 3.4k views

gen_t00

January 4, 20233 yr

Hi all, I’m trying to get KlipperScreen running directly on the framebuffer on a BigTreeTech CB1 that’s using an Allwinner H616B chip. It’s running Armbian Bookworm (kernel 6.6.66-vendor-sunxi64, Dec 2024 build) on a Manta M8P V2.0 board with a TFT35-SPI display that shows up as fb_st7796s. The goal is to have KlipperScreen render directly to /dev/fb0 without needing a desktop or HDMI. The framebuffer itself seems fine as the screen shows the BigTreeTech logo on boot, and I can write to it manually, so the driver appears to be working correctly. KlipperScreen installs fine, the Python environment and dependencies are all in place, but when I launch it, I always ge…

• 0

  Reputation Points

• 1 reply
• 3.3k views

JohnTheCoolingFan

October 25, 2025Oct 25

HI, recently downloaded Armbian Jammy CLI for Orange Pi Zero 2 It boots up but doesn't display anything on HDMI. I have to access it via remote ssh on another computer. Any way to enable the HDMI. I was hoping to run a desktop on it. Reading different forums it's suggested that the default check is too short so HDMI is disabled but I've no idea how to disable this. Will there be a desktop version of Jammy for Orange pi Zero 2 available to download? I'm using Jammy with a desktop on a Orange Pi One and it works fine. Thanks

• 0

  Reputation Points

• 3 replies
• 3.3k views

ALIGMSTEN

November 24, 20223 yr

I am trying to display a bootlogo.bmp on boot without success. HDMI and also LCD. I don't mean the four tuxes (pines) on kernel load, i want to display it from u-boot. I am using Armbian 5.26 (don't know why kernel is 3.10.104), upgraded from 5.25. I have placed bootlogo.bmp on /boot but still nothing displayed by u-boot. All my u-boot builds also fails to display it. Has anyone tried it with success?

• 0

  Reputation Points

• 3 replies
• 3.3k views

Igor

June 12, 20179 yr

The notes here, https://www.armbian.com/pine64/ talk about a beta image that has hardware acceleration enabled for the pine64. Unfortunately, the link is no longer valid. Anyone have a link to images I can use with the pine64 that have hardware (2d primarily) that i can use?

• 0

  Reputation Points

• 4 replies
• 3.3k views

zador.blood.stained

April 9, 20179 yr

I tried to flash the latest Armbian (Armbian_5.52.180715_Pine64_Ubuntu_bionic_dev_4.18.0-rc4) on my A64+. When starting I can't bott and gett one of these error messages: Does anybody have any idea what might go wrong? I know it's not stable yet. After that message, the device waits for an image from a TFTP Server.

• 0

  Reputation Points

• 0 replies
• 3.3k views
• 1 follower

starmagoo

July 31, 20188 yr

An extravagant man of boundless vision-part Raymond Loewy, component Buckminster Fuller, component Willy Wonka, and a smidgen Pepe Le Pew-Philippe Starck is nominally a industrial designer however truly an almost-anything-you-can-think-of designer. >> https://www.facebook.com/Bestmasticatingjuicers.zones He became famous in the 1980s and 90s because of his prong-like toothbrushes and citrus-juicers for Alessi, his sculptural chairs for Kartell, and his revolutionary interiors for Ian Schrager's first creation of boutique resorts, one of them New York's Royalton along with Miami Beach's Delano. Since then, his interests have ranged wider still, from his Sta…

• 0

  Reputation Points

• 1 reply
• 3.3k views
• 1 follower

Igor

June 7, 20188 yr

Hi, Since I still couldn't find a enclosure for my Pine64 H64 model-B, I mocked up one myself using a Eur 6,50 Raspberry Pi 4 case. 1) From the USB/ETH connector side I cut out the sections in between the connectors since there is a small offset that pushes the Pine64 board aside when closing the case. 2) From one of the cover lulls, I cut out a section to fit over the IR sensor. 3) On the HDMI side I cut out the two ports holes of the RPI micro hdmi connections and I made a notch in the USB-C hole to fit the power connector of the Pine64. 4) Drilled a hole in the cover large enough for the WIFI/BT antenna connector, on the board,…

• 0

  Reputation Points

• 1 reply
• 3.3k views

jeanrhum

April 26, 20206 yr

Hi, Armbian gurus. I tried latest Armbian image for PineH64-b. (Armbian_20.11_Pineh64-b_focal_current_5.8.16_desktop) And I surprisingly found there is no audio device when I looked around.( by #aplay -l ) Is this expected for now? My older 5.6 kernel has HDMI device at least. I tried search audio problem around but had no discover so far. Please allow me to confirm with you. I'm looking for a good 5.8 multimedia-capable kernel to merge with my gentoo rootfs. Thank you.

• 0

  Reputation Points

• 4 replies
• 3.2k views

Pander

August 28, 20224 yr

I'm trying to install armbian to the attached emmc with armbian-config. However i get the message "There are no targets, please check your drive". With fdisk -l the emmc doesn't show up. I do know the emmc is working properly because pull out the sd card (after shutting down) and reattach the power it boots from the emmc into android. Does anyone know to fix this? Systeminfo: http://ix.io/1q2B

• 0

  Reputation Points

• 1 reply
• 3.2k views

Igor

October 26, 20187 yr

Hi everyone, I downloaded a 6.12.68 image for my Bigtreetech Pi, compatible with CB1-sd. After apt update and apt upgrade, onboard ethernet disappears. During update got these messages: - Err: 16 http://deb.debian.org/debian trixie-backports/main arm64 Packages.diff/Index Could't find the start of the patch series - Notice: Repository 'http... InRelease' changed its 'Version' value from '13.3' to '13.5' Launching a new apt update, error and notice disappear. After upgrade and reboot there is no more ethernet device, just wifi. Investigating a little I found the kernel module sunxi_gmac.ko that was present in folde…

• 0

  Reputation Points

• 9 replies
• 3.2k views
• 1 follower

Igor

August 2Aug 2

Hello, I've been using OPiZ2 for about 2 years as Pi-hole in gravity-sync with another one (Orange Pi 3 LTS running Open Media Vault with no problem). Today I found out it was dead, no connection and just a blank screen. It must have happened in the past few days, because I checked it on sunday and it was up and running. I'm almost sure I was using it with Armbian_22.11.0-trunk_Orangepizero2_sid_edge_6.0.6. i have extracted the sd card and checked it on Windows with Diskinternals reader and Minitool Partition Wizard, no problem found. The most recent files and folders have been modified on 2024-07-12, eleven days ago, much prior to my checking, so…

• 0

  Reputation Points

• 2 replies
• 3.2k views
• 1 follower

jan_axhell

July 29, 20242 yr

By following the instruction how to enable ili9486 on orange pi, I have tried to do that with pine64. So, I installed armbian focal 22.10 with 5.15 kernel, enabled spidev and overlayed dts with tft installation and initialization. But still have a white display. Also I was trying another way to use/edit fbtft, the same issue. `dmesg` shows that spi driver no compatible with ili9486

• 0

  Reputation Points

• 3 replies
• 3.2k views
• 2 followers

robertoj

January 21, 20251 yr

Hi. Is there no support for btrfs in the latest armbian-ubuntu-xenial for Pine64s? Linux pine54 3.10.104-pine64 #2 SMP PREEMPT Thu Feb 23 22:26:21 CET 2017 aarch64 aarch64 aarch64 GNU/Linux root@pine54:~# mkfs.btrfs /dev/sda1 btrfs-progs v4.4 See http://btrfs.wiki.kernel.org for more information. failed to open /dev/btrfs-control skipping device registration: No such file or directory Label: (null) UUID: d8362fb9-1b9c-4d92-8222-6745f842efcf Node size: 16384 Sector size: 4096 Filesystem size: 7.04GiB Block group profiles: Data: single 8.00MiB Metadata: DUP 368.62MiB Sys…

• 1

  Reputation Points

• 1 reply
• 3.2k views
• 1 follower

zador.blood.stained

March 28, 20179 yr

When I tried using a c++ library called sfml which tried opening a window and it gave me an error and after trying every solution on the internet I gave up. And after trying other Debian images I noticed all of them don't have a desktop environment pre installed. So does Debian have graphics at all?

• 0

  Reputation Points

• 2 replies
• 3.2k views
• 1 follower

oleksii_laa

July 23, 20251 yr

I'm running Octoprint on Orange Pi Zero 2 and Armbian 22.11.3 Bullseye with Linux 4.9.318-sun50iw9 (other than assorted added userspace software, it's stock Armbian, no recompiled kernel or anything like that). It works great - while it works. I successfully complete 30+-hour prints. I can connect, monitor, everything is fine and dandy. When I'm connected to Octoprint from PC, monitoring of the 3D printer enabled, even without printing anything, it works ok. But if I'm not connected, and the printer is doing nothing for a prolonged time (an hour or so?), it stops working. Probably goes to sleep - stops responding to any network communication. Since it's a fully headless s…

• 0

  Reputation Points

• 1 reply
• 3.1k views

Werner

September 1, 20233 yr

Hi, Just want to check what the recommended approach is with today's dist-upgrade. I noticed that armbian-bsp-cli-pine64 was held back, so tried a manual install to see what the problem was. Seems like apt wants to remove linux-focal-root-current-pine64 to upgrade armbian-bsp-cli-pine64. Is this a temporary dependency issue? Obviously not performing the upgrade unless informed of the correct approach. BR.

• 0

  Reputation Points

• 1 reply
• 3.1k views

Igor

May 25, 20215 yr

Over the years have been using the Pine64 2Gb computer as an automation server running with original Xenial Base Image [20161218-1] by longsleep. This is a first generation Pine64 2Gb computer that I got during the start up of the company. Currently utilizing a 2 AMP 5VDC PS connected to the Euler bus, heatsinks on the top and bottom of the board and a boot up 100Mb mode. It would run fine for months then occassionally wouldn't start on boot. Recently redid the box using Armbian. | _ \(_)_ __ ___ / /_ | || | | |_) | | '_ \ / _ \ '_ \| || |_ | __/| | | | | __/ (_) |__ _| |_| |_|_| |_|\___|\___/ |_| …

• 0

  Reputation Points

• 3 replies
• 3.1k views

Petee

April 17, 20197 yr

Does anyone know where i can find linux headers for the LTS/Sopine, or an image that contains them? None of the images from the wiki seem contain the headers. I installed the Armbian legacy with 3.10.107 and was able to get Pine64 headers using apt-get install linux-headers-pine64 but they seem to be missing many files when i try to compile. Any help is greatly appreciated.

• 0

  Reputation Points

• 1 reply
• 3k views
• 1 follower

obrienmd

June 21, 20188 yr

Hi guys, I am newbie, my monitor iiyama ProLite B2888UHSU is flickering random white lines on black screen. U-boot console was displayed correctly. Same flickering I have seen on stock Armbian Bionic mainline kernel 4.19.y (next). Only Armbian Xenial desktop legacy kernel 3.10.y is working correctly. Can you help me? Maybe I can fix it, too, but I don't know, how and where to start. Thanks

• 0

  Reputation Points

• 2 replies
• 3k views

jadamcak

March 27, 20197 yr

How can PINE A64 GPU hardware acceleration be enabled? Playing a 24 fps full HD MP4 movie is not working smoothly. Here are some results on Armbian Jammy cli from June 30 version 22.05.3 with only installing via apt-get: - mpv, best result, probably ~10 fps - mplayer -vo sdl/fbdev2, probably ~5 fps - cvlc, probably 2~3 fps - kodi, probably 1~2 fps - gst123, could not get it running because issue with ALSA The fps are sort of guessed. Any other software and tips for testing are welcome. None of the movies playing played sound. speaker-test also did not play sound even though alsamixer showed all is well. Tips for this please too. …

• 0

  Reputation Points

• 3 replies
• 3k views
• 1 follower

Pander

October 3, 20224 yr

Hi, I've changed the default console from ttyS0 to ttyS3, using the mainline kernel with overlay "/boot/dtb/allwinner/overlay/sun50i-a64-uart3.dtbo". Unfortunately when I run command "sudo shutdown -r now" (or sudo reboot) my pine shuts down instead of reboot (although the console output says "reboot: Restarting system" at the end.) [Hard reset reboot works with "reboot -f" using ttyS3 console]. Using the standard console I can reboot my pine without problems. What could case this behavior? Is it necessary to disable or kill a ttyS3-process before the reboot?

• 0

  Reputation Points

• 2 replies
• 3k views
• 1 follower

linda

April 3, 20188 yr

Hello, I am using Allwinner A64 processor for my use case. In that, I want to flash my custom os into emmc memory which is alredy worked in SD card. Currenlty we go thorugh below link: https://wiki.pine64.org/index.php/NOOB#Instructions_to_Flashing_eMMC_Modules we follow "xzcat imagename.img.xz | sudo dd of=/dev/mmcblk1 bs=1M status=progress conv=fsync" this command but we got input/out error while reading memory. Please check below screenshot.

• 0

  Reputation Points

• 1 reply
• 3k views

Werner

October 5, 20215 yr

Hello, Hopefully a maintainer is reading- is there a plan to build/release 24.8 for Orange Pi Zero 2? Thanks!

• 0

  Reputation Points

• 1 reply
• 3k views

Werner

October 22, 20241 yr

I have Armbian up and running very nicely on the PineA64+ 2GB board. Thanks to the community! Speed concerns aside, is it possible to attach a SATA drive to this board? What would be the recommended way to do so? It is the availability of large storage capacity that we need for our project, not blazingly fast disk writes.

• 1

  Reputation Points

• 1 reply
• 3k views
• 1 follower

Igor

August 5, 20179 yr

Hello, I have Pine64 2GB I want to connect the temperature sensor DS18B20. How to connect it. Sorry for my English

• 0

  Reputation Points

• 2 replies
• 3k views

chwe

May 5, 20197 yr

I've been building armbian xenial images for my pine64+ a few times now and it works well. But I would like to switch to bionic if I can. I find it hard to find a good place of documentation for either the 4.x kernel or ubuntu bionic for armbian, specifically for A64/Pine64 boards. If I google, I see tons of forum posts with specific issues, but no coherent overview of any issues with 4.x kernels? And reading through 2-3 years of replies on some threads is a bit much to find the info I need. So what would or wouldn't work on a 4.x kernel on ubuntu bionic? Also, I am confused about who does what, and therefore where to go with problems. How are longsleep or sunxi involved …

• 0

  Reputation Points

• 0 replies
• 3k views

Dolf Andringa

November 5, 20187 yr

Hello, First of all, thank you so much for putting these images together. Kudos to you all for some great work! Now on to my issue. I installed Xenial build and it booted up nicely to XFCE. The only issue I am having is no audio over HDMI. I know the display works for HDMI audio as my nVidia Shield works fine. Any help on determining the issue? If you need any logs, boot messages, and/or config files, let me know. Thank you in advance, Brian

• 0

  Reputation Points

• 1 reply
• 2.9k views

Igor

July 11, 20188 yr

any one have a succes with? using Armbian_25.2.2_Bananapim4zero_noble_current_6.6.75.img wifi not work, thats fixed with: overlays=bananapi-m4-sdio-wifi-bt Applying kernel provided DT overlay sun50i-h616-mcp2515.dtbo failed on fdt_overlay_apply(): FDT_ERR_NOTFOUND and then: Error applying DT overlays, restoring original DT and have no wifi and any overlays at all.. on a bpi 2W Zero runs double mcp2515 on a spi1 as can0 + can1, but on M4 zero - no success at all, everythings are tried, all armbian builds, trying self writed overlays, tried boot from uSD, emmc - no success. always took this…

• 0

  Reputation Points

• 3 replies
• 2.9k views

Netcrusher

December 26, 2025Dec 26

Hello everybody, since an Softwareupdate some time ago, i m not able to boot up the Pine64 with any Image. It doesnt matter what distro, or what channel. Does anybody have the same issue?

• 0

  Reputation Points

• 3 replies
• 2.9k views

martinayotte

August 8, 20188 yr

Let me think about how to descript this situation...... I have a movable disk and mount in path: /mnt/sba1 It happened first time when I using a program called "Syncthing" , I try to sync my file into my movable disk. I get lot of files in my directory. When the "Syncthing" start scanning. the system will stuck. Not that kind of whole system stuck, but only if you trying to read anything about /mnt/sda1. If you trying to "df -h", you'll get stuck. "fdisk -l", stuck. "cd /mnt/sba1", stuck again. "mount" "umount" "lsblk" all will be stuck. Such like this ...... Reboot the system is only way to restore.…

• 0

  Reputation Points

• 1 reply
• 2.9k views

TheOWL

June 8, 20233 yr

Hi I have Pine64+ with LCD + TouchScreen - all from Pine team. I checked some OS, but only Armbian DE is responsiveness enough for me. Now, Armbian Jessie is on SD card, stable ISO with all updates and upgrades installed - 3.10.107-pine64. Change from HDMI to LCD done by changing pine64_lcd to 'on' in /boot/armbianEnv.txt I add gt9xxf_ts in /etc/modues and restart Pine64. But cursor doesn't move on any touch. I confirm that the gt9xxf_ts module loaded by runing 'lsmod' as root, but this module is used by 0 (nobody). I've checked which event is assigned and I got: cat /proc/bus/input/devices | grep -B 2 -A 8 gt9xxf_ts I: Bus=…

• 0

  Reputation Points

• 0 replies
• 2.9k views
• 1 follower

zielec

August 9, 20188 yr

i have a alfa awus036acm wireless adapter install on my orange pi one with armbian jammy installed. my awus036acm adapter is not recognised , when i type iwconfig it's say no wireless extension is there possible way to make it work?

• 0

  Reputation Points

• 1 reply
• 2.9k views

Igor

December 16, 20223 yr

Hi, I brought new pine64 board and installing OS in SD card. This OS considering kernel 5.10.34 and now I want to modify some of the kernel features. For that, please guide me how to download kernel source and rebuild it for pine64.

• 0

  Reputation Points

• 1 reply
• 2.9k views

Werner

June 5, 20215 yr

I need to use a 10 inch 800x600 DSI display in a Pine64 project and I think the easiest way to do this would be to modify the driver for the Pine 7 inch DSI display. It appears to me that the display resolution is hard coded in this driver (panel-feiyang-07024di26a30d.ko) and not supplied by a device tree overlay like some other Armbian SBCs. In the C source for this driver, I see the following data structure which defines a 1024x600 screen size for the 7 inch display ... static const struct drm_display_mode feiyang_default_mode = { .clock = 55000, .hdisplay = 1024, .hsync_start = 1024 + 310, .hsync_end = 1024 + 310 +…

• 0

  Reputation Points

• 1 reply
• 2.8k views

DasFisch

January 21, 20251 yr

Hi, When will soon be ready for the Armbian Pine A64 Desktop Debian? Can I now install Debian xfce on the Armbian Pine A64 Server? and how? Thank you

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

Hannover

November 7, 20169 yr

Hi, Thank you all for so much work to fully implement the mainline kernel for the Pine64! So much is now working out-of-the-box with armbian, that there is no need to use the legacy version based on kernel 3.10. The pine64 does have CIR capabilities and the sunxi-cir kernel module is available, but we are still missing DT bindings for the device, although I see that an overlay file is present for the h5: /dts-v1/; / { compatible = "allwinner,sun50i-h5"; fragment@0 { target = <0xffffffff>; __overlay__ { pinctrl-names = "default"; …

• 0

  Reputation Points

• 1 reply
• 2.8k views

Learnincurve

December 17, 20205 yr

What version of armbian is the best overall for the opiz2 ? im mainly going to use it as a server so no desktop.its gonna run some python code for my bots. i might move it around so wifi with 5ghz support is a must .

• 0

  Reputation Points

• 0 replies
• 2.8k views

hardcod3dd

December 7, 20223 yr

@Igor What is the status of the orangepione? On the download page there are no images presented yet in the build framework is shows up as "conf" in the support (1st) page.

• 0

  Reputation Points

• 4 replies
• 2.8k views
• 1 follower

Stephen Graf

February 5, 20242 yr

My OPIZ2 was working happily with Armbian_bullseye 22.11, but due to the wifi issue, I download the Armbian_bullseye_22.02 dan flash the image into the same working SD card (overwritten). But now my OPIZ2 would not boot anymore, nothing seen in the serial communication either. No red/green LED ever lit. Sadly, this is my 2nd dead OPIZ2..... Seeking for help if those boards are still recoverable...

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Werner

January 6, 20233 yr

I have been running Armbian on a headless Pine64 (the kickstarter one) for quite sometime without any issues. Last week I woke up in the morning and noticed that there had been a power cut. The Pine64 was on again but I couldn't SSH into it. I plugged a monitor and found the system hangs while booting with the following error: Error while loading shared libraries: lib system-shares-241.so: cannot open shared object file: No such file or directory Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00 CPU: 1 PID: 1 Comm: init Not tainted 5.4.43-sunxi64 #20.05.2 Hardware name: Pine64+ (DT) Call trace: dump_backtrace+0x0/0x180 show_stack+0x14/0x20 dump_s…

• 0

  Reputation Points

• 1 reply
• 2.8k views

Igor

December 29, 20205 yr

Hi!I am trying to connect B101UAN01.7 display(1920 x 1200) without any success.Is pine64's driver supports other display than native 7"? If so, then could you please help me to understand where can be error?Here is cutout from my device tree for 10.1" display lcd0@01c0c000 { compatible = "allwinner,sunxi-lcd0"; pinctrl-names = "active", "sleep"; status = "okay"; device_type = "lcd0"; lcd_used = <0x0>; lcd_driver_name = "mb709_mipi"; lcd_backlight = <0x32>; lcd_if …

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

vicb

June 1, 20179 yr

Ciao dears, I hope this is the correct section. I tried to find a solution in this and other forums, but I found dated post . I try to open one with the hope of solving the problem also for others I'm having trouble getting the camera module s5k4ec to work for my pine64 running armbian 5.60 #cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=16.04 DISTRIB_CODENAME=xenial DISTRIB_DESCRIPTION="Ubuntu 16.04.5 LTS" Here my armbianmonitor -u http://ix.io/1wU9. i've activated the module in/boot/armbianEnv.txt verbosity=1 console=both disp_mode=720p60 camera_type=s5k4ec pine64_lcd=off overlay_p…

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

Lendi

December 27, 20187 yr

I have OPIZ2 been running for months for node-red and MQTTbroker. Due to crappy configuration I did during the insallation, then I decided to replace the OS and reconfigure all, I used the same SDcard and reflash with same Armbian_23.5.2_Orangepizero_jammy_current_6.1.30. But, beyond this point, OPIZ2 never boots anymore... I tried other armbian version and it is the same dead. If I use a fresh SD card (Sandisk 16GB A1) then it works ok. My question is regarding the SD card imaging ( i am using Balena-etcher), is there something change inside the SDcard after reflash so that OPI does not recognise the booting part anymore??

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Werner

July 9, 20233 yr

Hi everyone! I'm trying to build my own distribution for the Pine64, and I use armbian as a working reference. I'm able to compile ATF + U-boot + Kernel + rootfs and the board actually boots and I get a console over the serial interface and over HDMI. The problem is that GbE Ethernet does not work. It appears that the 8211 phy is not powered. The good guys on the pine64 IRC pointed to the ATF, where the DC1SW regulator should be turned on in order to power the phy. On armbian everything works just fine. I think I messed up something in the build - wrong version / config / dts in either ATF, U-boot or the linux kernel. …

• 0

  Reputation Points

• 0 replies
• 2.8k views

Avraham Shukron

December 22, 20196 yr

I'm using a Pine 64 LTS. For this I have downloaded the SoPine images Armbian_21.08.1_Pine64so_buster_current_5.10.60.img and Armbian_21.08.1_Pine64so_focal_current_5.10.60.img Both images boot normally (including network connection), but after the update (apt update, apt upgrade) no IP4 network connection is established for eth0. For help I am very grateful for any help.

• 0

  Reputation Points

• 2 replies
• 2.7k views

Pander

August 28, 20224 yr

Found an interesting way to keep the Pine64 cool. https://www.youtube.com/watch?v=VFq1EbWOfYo

• 0

  Reputation Points

• 1 reply
• 2.7k views

Dan25

February 24, 20179 yr

Hello, Ive setup ssh and did some stuff on my OrangePi, when i came back and plugged my phone into power hub my OrangePi was connected to, it restarted and stopped at disk manager, i restarted it and it gave lots of failed messages, i restarted and it didnt work anymore :( it only gives yellow ethernet led and nothing else, i also reflashed sd card because it got all partitions gone after that incident Please help!!!

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

Werner

December 17, 20241 yr

Running Armbian Ubuntu Xenial 16.04 on a PineA64, legacy kernel 3.10.105-pine64. Why is it necessary or desirable to put the variable 'ethaddr' in armbianEnv.txt? I thought the hardware mac address would be detected by the kernel. Perhaps not?

• 0

  Reputation Points

• 1 reply
• 2.7k views

Andro

September 8, 20179 yr

After a fresh armbian installation + armbian-firmware-full package, the pine64 bluetooth doesn't work because the rtl8723bs_config-pine64.bin file is missing. I've downloaded the file from https://github.com/anarsoul/rtl8723bt-firmware/tree/master/rtl_bt into /lib/firmware/rtl_bt and it works so I've created a PR here https://github.com/armbian/firmware/pull/14 to add it to the firmware package so it can work out of the box. Let me know if I need to do something else for the PR to be merged. Thanks.

• 0

  Reputation Points

• 0 replies
• 2.7k views
• 1 follower

eminguez

April 28, 20206 yr

My Pine64 boots using Armbian_5.30_Pine64_Ubuntu_xenial_default_3.10.105_desktop. I have added pine64_lcd=on to /boot/armbianEnv.txt and updated the module file. But now when I plug in HDMI nothing displays on the HDMI screen. I also can not see it as a secondary display. Is it possible to have both displays on or can I only have one, having to remove LCD if I want HDMI output?

• 0

  Reputation Points

• 0 replies
• 2.7k views

Zululander

August 14, 20179 yr

I am new to this whole endeavor and I am attempting to SD-cardless boot my orange pi zero 2 and after nearly a week of playing around have it nearly working. I have custom compiled Armbian 23.08.0-trunk with Bookworm and 6.2.16 kernel with ROOTNFS set to Y I have unpacked rootfs to my NFS server I have setup PXE booting via pxelinux.cfg/01-<mac address> I have u-boot working from SD Card ( It technically works from SPI but gives temperature error every boot of kernel) I can boot all the way into a functioning OS. My problem is that while PXE booting allows for loading overlays, I cannot load a fixup.scr or similar via PXE from what I can tell. I have …

• 0

  Reputation Points

• 0 replies
• 2.6k views

Whinis

May 28, 20233 yr

Hello, I am looking for a specific legacy image for the Orange Pi Zero 2W: Armbian 23.02.2 Bullseye with Kernel 5.10.160. The reason I need this specific version is to use the device as a USB UVC (Webcam) gadget via ConfigFS. On the newer 6.6/6.12 mainline kernels, I am facing a "Permission Denied" error when trying to write to hHeight, even as root. After researching, it seems this is a known kernel-level restriction in newer versions, and the legacy 5.10 kernel is the most stable for UVC gadget functionality. I’ve checked the current archive mirrors but could only find the 6.6.x versions. Could anyone provide an official archive or a reliable mirror link …

• 0

  Reputation Points

• 1 reply
• 2.6k views

Werner

December 20, 2025Dec 20

Hi there! How to disable private ethernet MAC on OPZ2? Router says my device has one.

• 0

  Reputation Points

• 1 reply
• 2.6k views
• 1 follower

Hans.K.K.

January 27, 20233 yr

Are there any plans of creating an image incorporating an mainline 4.xxx kernel for the pine64 boards? Kernel.org states the projected EOL for the 3.10 kernel line as october 2017.

• 0

  Reputation Points

• 1 reply
• 2.6k views

Igor

April 19, 20179 yr

I have looked up relevant information on Google. Since 5.6, pine a64 already supports dsi in the kernel mainline.And the Feiyang FY07024DI26A30-D 7inch MIPI-DSI LCD Panel driver and dts already released. But the 7inch lcd above is a video mode panel.I can not found any information about the command mode panel. Is pine a64 mipi-dsi supports command mode from the kernel mainline? Any help is appreciated!!

• 0

  Reputation Points

• 0 replies
• 2.6k views

jam

May 26, 20215 yr

Hello. BTT says what BTT Pi and CB1 is same, but realy not. Dunno why i brought what board. But now I owner of this "piece of ****" So. New board, clean install v25.11.2 for BigTreeTech CB1 running Armbian Linux 6.12.58-current-sunxi64 Packages: Debian stable (trixie) armbianEnv: overlays=gpu tft35_spi extraargs=fbcon=rotate:2 fbcon=rotate:2 for screen rotation, because armbian not from btt and didn`t have feature like param_tft35_spi_rotate Next, help me to determine how to enable UARTs and I2C From BIGTREETECH_Pi_V1.2.1 Hardware Pdf UART0: CPUX-UTX CPUX-RX UART2 (May work as i2c0; uart2-pi-pins;…

• 0

  Reputation Points

• 2 replies
• 2.6k views
• 1 follower

ComProf

March 13Mar 13

This is only my perception. I have this three SBC.: PINE 64 +, Nano PI A64, Banana pi M64. Everything on A64 allwinner chip. Armbian Image for Pine 64 works both Pine and Bananapi M64. But does not work NANO PI A64. Other third party software ( systems ) Remix, Ubuntu, work pine and banana pi and dont work nano pi. Only android 5.1.1 works on these three SBC....

• 0

  Reputation Points

• 1 reply
• 2.6k views

zador.blood.stained

April 11, 20179 yr

Everytime i reboot and/or turn-off both of my Pine A64, they dont boot again until i manually turn-off/on them a lot of times, is there any fix to it? the img i use is: Armbian_5.35_Pine64_Debian_jessie_default_3.10.107.img

• 0

  Reputation Points

• 4 replies
• 2.5k views

barart

February 7, 20188 yr

Suddenly the 6.16 kernel was released in apt , who did it? why all overlays missed?

• 0

  Reputation Points

• 3 replies
• 2.5k views

Werner

August 18, 20251 yr

I have a feeling this was caused by a p[roblem with the definition of ftdfile variable: line from boot.cmd: load ${devtype} 0 ${fdt_addr_r} ${prefix}dtb/allwinner/${fdtfile} from the serial output: File not found /boot/dtb/allwinner/allwinner/sun50i-a64-pine64-plus.dtb ** note the duplication of Allwinner. Since I couldn't find where it was defined , I just copied the allwinner directory into itself.....:-) which fixed the problem. Perhaps someone could look into this? thanks.

• 0

  Reputation Points

• 2 replies
• 2.4k views

belfastraven

December 1, 20178 yr

Fresh install on the latest image (Armbian_25.2.2_Bigtreetech-cb1_bookworm_current_6.6.75_minimal.img.xz). First thing I wanted to do was an armbian-upgrade, but: Hit:1 http://deb.debian.org/debian bookworm InRelease Hit:2 http://deb.debian.org/debian bookworm-updates InRelease Hit:3 http://security.debian.org bookworm-security InRelease Hit:4 http://deb.debian.org/debian bookworm-backports InRelease Hit:5 https://github.armbian.com/configng stable InRelease Hit:6 https://netcup-02.armbian.com/beta bookworm InRelease Reading package lists... Done W: Target Packages (main/binary-arm64/Packages) is configured multiple times in /etc/apt/sources.list:1 and /etc…

• 0

  Reputation Points

• 4 replies
• 2.4k views
• 1 follower

Paul Damian

May 14, 20251 yr

I've got an Pine64 a that was one of the Kickstarter models. For a couple of years I've been running OctoPrint on it to run my Qidi i-mates 3d printer. Recently I decided to update from jammy to noble, before I did that I made a backup of my OctoPrint settings and files through the OctoPrint GUI in case of problems. I got a really messed inconsistent with all sorts of dependencies errors because the apt dist-upgrade seemed to freeze and after several hours of no movement I rebooted. As expected it was the mess. I spent about an hour on fixing dependencies but decided it just wasn't worth it as the only thing running is OctoPrint. When I went to restore OctoP…

• 0

  Reputation Points

• 1 reply
• 2.4k views
• 1 follower

laibsch

June 26, 20251 yr

I have PINE A64 WIFI 802.11BGN/BLUETOOTH 4.0 MODULE I can see wifi card but bt is not working Please help me to make this bt module working $ sudo rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no $

• 0

  Reputation Points

• 2 replies
• 2.4k views

Onira

July 17, 20251 yr

Hello, I downloaded the latest 20.04 image for Pine64+ and I am not getting any audio from youtube for example. I can see in the Volume Control window in the Output panel an audio level meter moving and the application Chromium. But still get no audio from the TV.

• 0

  Reputation Points

• 1 reply
• 2.4k views

Pander

April 22, 20233 yr

Hi I set the DSI format to RGB888. However, looking at the output of DSI seemed to be BGR888 format, why?. About DSI format I confirmed the Allwinner A64 SoC specification, but I did not understand it well. The software and hardware used are as follows. software: Armbian hardware: Pine A64-LTS Thank you.

• 0

  Reputation Points

• 0 replies
• 2.4k views

RyoTanaka

February 22, 20197 yr

I have one on a shelf and want to use it for h265->h264 transcoding. http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-One-Plus.html says it can. H6 Quad-core 64-bit ARM Cortex™-A53 Decoding: H265/HEVC Main/Main10 profile@Level5.2 High-tier ;4K@60fps, up to 6Kx4K@30fps Encoding: H.264 BP/MP/HP encoder up to 4K@25fps or 1080p@60fps Googling finds some old branches of ffmpeg and kernel for H3. Current armbian 25.2.3 comes with 6.12.20-current-sunxi64 which has: sunxi_cedrus v4l2_mem2mem videobuf2_dma_contig videobuf2_v4l2 videodev videobuf2_common …

• 0

  Reputation Points

• 2 replies
• 2.3k views
• 1 follower

aik

May 20, 20251 yr

Everything come from a try to create a docker compose project. Armbian 24.8.4 bookworm on OrangePI zero 2 - Network forwarding doesn't work: ``` version: '3.6' services: db: image: mariadb:10.3 environment: MYSQL_ROOT_PASSWORD: secret phpmyadmin: image: phpmyadmin restart: always ports: - 8080:80 environment: - PMA_HOSTS=db ``` => FROM test-db-1 => test-db-1 3306 ``` docker exec -ti test-db-1 bash -c 'timeout 0.5 echo -n 2>/dev/null < /dev/tcp/test-db-1/3306 && echo "open" || echo "closed"' ----------- open ----------- ``` => FROM test-phpmyadmin-1 =…

• 0

  Reputation Points

• 0 replies
• 2.3k views

Jeremy Levy

November 7, 20241 yr

https://www.pine64.org/pinephone/ It gets the same cpu as the pine64. If you have a pine64 can it run common programs like firefox, vlc, libre office, gimp and jitsi? Is the pine64 as fast as the orange pi one?

• 0

  Reputation Points

• 0 replies
• 2.3k views
• 1 follower

renky

September 4, 20197 yr

Hi How do I change the DSI clock for Pine A64-LTS ? Thank you.

• 0

  Reputation Points

• 0 replies
• 2.2k views

RyoTanaka

October 31, 20187 yr

Hi, on latest Armbian 23.11.1 Bookworm with PINE64 board I noticed those warnings in journal: Feb 12 10:00:45 pine64 systemd[1]: /lib/systemd/system/systemd-journal-upload.service:33: Unknown key name 'RestartSteps' in s> Feb 12 10:00:45 pine64 systemd[1]: /lib/systemd/system/systemd-journal-upload.service:34: Unknown key name 'RestartMaxDelaySec> I suspect the `systemd-journal-upload.service` is not in tact with systemd daemon version installed.

• 0

  Reputation Points

• 0 replies
• 2.2k views

cvxx

February 12, 20242 yr

Hi, just want share a little experiment I am doing to try to solve my Pine64 Boot Crash/Freeze Problem using a external (MCU) microcontroller to assist it. [MCU and Pine Drawing] [Actual Prototype Photo] The idea is very simple, just "watch" the SystemLED to detect if the system is booting normally, and if NOT, then issue a hardware reset, then, keeping repeating this process until the SystemLED indicates that the system is booting up... I am trying to document the process here is this tutorial page: http://www13.plala.or.jp/pskitty/copineon.html Files, source code, high quality pictures here on GitHub: h…

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

ecolezen

June 18, 20179 yr

I cannot boot into lvm encyprypted root partition: mount: mounting "/dev/mapper/vg-root on /root failed: No such file or directory␍␊ Failed to mount "/dev/mapper/vg-root as root file system.␍␊ The flollowing step i made (short version) - create the lvm partition - mount lvm partition and and copy file system auf lvm partition, bind /dev, sys, proc - chroot in the lvm root partition (vg-root) - change /etc/fstab : insert /dev/mapper/vg-root / ext4 errors=remount-ro 0 1 UUID=<UUID-Partiion> /mnt/mnt ext4 defaults,noatime,nodiratime,commit=600,errors=remount-ro …

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

linda

July 29, 20224 yr

As highlighted by an issue on BTT's GitHub, why are two wireless interfaces present (wlan0 and wlan1)? What should we use ? armbian-config presents them both.

• 1

  Reputation Points

• 3 replies
• 2.2k views
• 1 follower

Igor

November 18, 2025Nov 18

What's the current status of 5.30 on Pine64 mainline? I've a spare Pine64 lying around and was considering compiling latest Armbian for it to poke around a little, test things if that's useful to the dev effort. The downloads page lists support as experimental, but the version there is 5.27 and some of the info seems out of date, ie points to the wrong subforum, etc.

• 0

  Reputation Points

• 0 replies
• 2.2k views

reverend_t

August 21, 20179 yr

Hello , i have used now for some year armbian for this board, very many thanks for that; lately have updated to newer version Debian Trxiie and found that "htop" report a higher CPU usage after freshboot (around 50%) whereas previously it sat a 10% probably; now when evoking htop it gives (CPU offline for core 2-3-4) also nproc report "1" instead of "4"=? not sure if this an error ; noticed a similar report of nproc also with a build of volumio; thank you very much;

• 1

  Reputation Points

• 4 replies
• 2.1k views

kapqa42

August 28Aug 28

After installing the latest update, my 3D printer warns about outdated instructions in the MCU and asks to recompile and flash it. What should I do?

• 0

  Reputation Points

• 1 reply
• 2.1k views

mattjm

June 3Jun 3

I set up a new Banana Pi M4 Zero, with an HDMI monitor that had previously been used with a Raspberry Pi, a USB hub with a keyboard and mouse. I downloaded the Armbian Ubuntu Jammy desktop, the activity light flashed a bit but no video. I soldered a header to the debug serial pads and connected to a PC through a serial to USB converter. Using that link I could see the boot process, and communicate. I used armbian-config to set up wifi etc, but still no video. I have tried Jammy minimum, and both Debian downloads but still no video. There appears to be nothing coming across the HDMI connection, the monitor detects that there is a physical connection but no video. The same …

• 0

  Reputation Points

• 0 replies
• 2.1k views

keithr

September 21, 20242 yr

boot0 version : 4.0.0 set pll start set pll end rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 DRAM driver version: V1.1 rsb_send_initseq: rsb clk 400Khz -> 3Mhz Set DRAM_VCC failed initializing SDRAM Fail. HELLO! BOOT0 is starting! boot0 commit : 045061a8bb2580cb3fa02e301f52a015040c158f

• 0

  Reputation Points

• 1 reply
• 2.1k views

pfeerick

June 22, 20179 yr

I'm currently looking into a new project which will use (hopefully) the Rpi Waveshare hdmi based 4" lcd touch screen, linked to the pine64/Sopine I'm at research stage, and will be looking into using a current 5.x kernel. If anyone has any info on the waveshare lcd's I need to watch out for or suggestions to get further info (specifically the touch driver side), please post a response. Progress on the project will be posted here, links will be added once I have some basics running. This can hopefully open up the waveshare displays to other devices. @Igor Yes I've read This post but am willing to do what I can to get Armbian to support the d…

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

Gavinb

January 27, 20206 yr

On a clean Armbian image (Armbian_23.5.2_Orangepizero2_jammy_legacy_4.9.318.img) I am not able to connect to an AP. nmcli or nmtui produces errors (https://paste.armbian.com/ogowinebol). This also holds for the other jammy_legacy images in the archive. When testing on the stock images provided orange pi I am able to connect with both the Orangepizero2_3.0.6_ubuntu_jammy_server_linux5.16.17.img and Orangepizero2_2.2.0_ubuntu_focal_server_linux4.9.170 images it works. Connecting also works on the Amrbian focal_legacy images I tried.

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

mklomp

August 9, 20233 yr

Hi, I need to set max_loop=128 to boot kernel parameter, I added to the armbianEnv.txt file but value seems zero when I look like that. cat /sys/module/loop/parameters/max_loop How can I modify that parameter? Thanks.

• 0

  Reputation Points

• 0 replies
• 2.1k views

cemzafer

May 7, 20188 yr

I wanted to try anything other than the original image that the device came with. I was more interested in the Kali port but after trying for a few hours with pretty much all the images available here I had to revert to the original one. So I was wondering if anyone here ever tried these images or could give me some hint on what is wrong with it ? Basically just getting a red led with no display when trying all the images. I know the original image had a some sort of special boot process where the initial startup would take some time but I know nothing else about armbian at this point. My goal was to start doing some test with kali liking t…

• 0

  Reputation Points

• 1 reply
• 2.1k views

Igor

April 7, 20251 yr

Just for curiosity, I've updated my Armbian on my Pine64 to the latest release. The latest u-boot for Pine64 (U-Boot SPL 2017.11-armbian (Jan 25 2018 - 08:32:21) seems to have an issue with the persistent u-boot environment. Once I've written a custom environment back to MMC using `saveenv´ the board hangs during boot. Environment size: 10335/131068 bytes => saveenv Saving Environment to MMC... Writing to MMC(0)... done => reset resetting ... INFO: PSCI Affinity Map: INFO: AffInst: Level 0, MPID 0x0, State ON INFO: AffInst: Level 0, MPID 0x1, State OFF INFO: AffInst: Level 0, MPID 0x2, State OFF INFO: AffInst: Level 0, MPID 0x3, State OFF …

• 0

  Reputation Points

• 2 replies
• 2k views

umiddelb

February 2, 20188 yr

Hi, I'm actually working on a project with this hardware: IR + controller : https://es.aliexpress.com/item/1005005651928240.html?spm=a2g0o.order_list.order_list_main.5.21a9194dT8Becw&gatewayAdapt=glo2esp MPR121: https://es.aliexpress.com/item/1005005097989944.html?spm=a2g0o.order_list.order_list_main.11.21a9194dT8Becw&gatewayAdapt=glo2esp Bluetooth speaker, but i would use the chip that comes with orange pi . My answer is that i have all of these working inside a raspberrie pi 3 b 1.2, with python to detect the mpr121 pulsations and ir pulsations and manage connection Bluetooth, my problem is that I want to be sure that works, and actually the …

• 0

  Reputation Points

• 0 replies
• 2k views

joitronix

February 16, 20251 yr

Hello all you awesome community members! So I got this Pine a64+ during their Kickstarter campaign. Initially I used it as a little play desktop. I never really found a use for it until very recently. I decided to use it as a little software Squeezebox client. I installed Armbian 22.04 server. I then setup alsa to use the HDMI audio as default output. I installed squeezelite and it immediately found and connected to my LMS (Logitech Media Server) running on my server. At this point I figured all was good. The sound was working great through my receiver. The next morning (Sunday) the kids could not get the TV sound to work. So of course …

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

BJWTech

July 25, 20224 yr

pine 64so Pine64, bananapi M64 images 19.11.3, GUI XFCE 4.12 dont not run after upgrade images 20.02 GUI does not work from begining after installed. Never mind i build 19.11.5 kernel 5.4.18 and works

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

constantius

April 11, 20206 yr

Hello, I have a Pine64 board and recently added an audio POT with the pcm5102a chipset. It is rather difficult to get the board working/recognized. I found info on the forum saying one has to do stuff with the overlay system but only for other boards than the Pine64 and I can't get it right. aplay -l: root@pine64:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sun50ia64audio [sun50i-a64-audio], device 0: 1c22c00.dai-sun8i-codec-aif1 sun8i-codec-aif1-0 [1c22c00.dai-sun8i-codec-aif1 sun8i-codec-aif1-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sun50ia64hdmi [sun50i-a64-hdmi], device 0: 1c22800.i2s-i2s-hifi i2s-hifi-0 [1c…

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

joho500

November 20, 20214 yr

Hi, I really apologise if the information is out there and I just haven't found it. I was looking to buy a board for a small embedded GUI application and this one seems to fit the bill. I would like to use Wi-Fi, Bluetooth and HDMI. Is there a list of what is working or not working on each build/version? (This is probably a more general question to Armbian for any device) The only thing I could find is this: But it's not that recent. On the download page: https://www.armbian.com/orange-pi-zero-2/ under specifications it does list, Bluetooth and Wi-Fi but I'm not sure if this means its now working? …

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

av4625

August 28, 20242 yr

Hi, Can anyone tell me how can i remove the wifi and ethernet services completely from the armbian.

• 0

  Reputation Points

• 0 replies
• 2k views

kapil

June 8, 20233 yr

Hello everyone, I am using an Orange Pi Zero 2W with a graphical user interface (GUI). I downloaded and installed the official Orange Pi Zero 2W image. Unfortunately, I keep running into a Wi-Fi connection issue. After booting, the system repeatedly asks me to enter my Wi-Fi password. If I don’t enter it, I have no internet connection. What’s interesting is: If I disable and re-enable Wi-Fi in the network manager, it automatically reconnects to the known network without asking for the password again. Alternatively, a system reboot also restores the Wi-Fi connection automatically. I have already seen o…

• 0

  Reputation Points

• 1 reply
• 1.9k views
• 1 follower

Werner

January 5Jan 5