Other families

Hi, A strange error appeared with the last kernel update on an Odroid HC2. From the home in the terminal displays this error under RX totay: RX today: Error: Interface "--oneline" not found in database. The board is hosting an OMV instance under Armbian Bullseye Linux version 5.4.212-odroidxu4. Does anyone have any idea about the origin of this message which does not seem to disrupt the NAS operation. thanks konki

• 1

  Reputation Points

• 5 replies
• 6.9k views
• 1 follower

porg

January 1, 20233 yr

Hey, the last time my Helios4's PSU blew I suspect was due to a power overload, with the PSU not being able to deal with all 4 HDDs doing active work (this also killed one of the HDDs in my array). Based on the system log, it looked like the system was doing a regular integrity checks on all 4 HDDs at once (!). I would like to either disable the integrity check altogether, or more ideally, spread it out. I have two RAID-1 arrays, and there is no reason for all four drives to be checked simultaneously. For example, I can check one of the arrays (two HDDs) and then once that is done, the second array (the other two HDDs) after. Does anyone know where…

• 0

  Reputation Points

• 1 reply
• 2.9k views
• 2 followers

djurny

October 3, 20224 yr

Hey guys! I am running Armbian 22.05.3 on my Odroid XU4. Very happy with it. I just installed linux-image-edge-odroidxu4 (kernel 5.17) and rebooted. Everything hunky dory. However, once I'm on 5.17 I am unable to reboot by using the 'reboot' or 'shutdown -r now' commands, which worked on the default 5.4 kernel. Is this a known issue? Any hints on how to debug or any known workarounds? Thank you

• 0

  Reputation Points

• 3 replies
• 3.1k views

Guest

October 22, 20223 yr

I have a new odroid XU4 that I plan to use for Home Assistant in Docker and run other services in containers. I have loaded a fresh copy of Armbian cli (fully updated) with bluetooth from armbian-config. I installed linux drivers for my usb module (rtl8761a) from the manufacturer and it comes up in "bluetoothctl" as registered and pairable. However "bluetoothd show" gives me a "D-Bus setup failed: Name already in use." I will need dbus to pass device information between my docker containers when I install docker and home assistant so this error is concerning. Any ideas on how I might resolve this error? Thank you armianmonitor url: http://ix.io/…

• 0

  Reputation Points

• 0 replies
• 2.9k views
• 1 follower

rostar99

August 26, 20224 yr

Hi all, The grey wifi Dongle 5 I bought direct from Odroid seems to have stopped working with recent Debian releases. After much troubleshooting, I downgraded to Buster and it works fine - until I run apt update/upgrade. lsusb info is: Bus 003 Device 010: ID 0bda:8812 Realtek Semiconductor Corp. RTL8812AU 802.11a/b/g/n/ac 2T2R DB WLAN Adapter What's also interesting is that post upgrade, the device's name also changes to @_____, and its mac address changes to 00:00:00:00:00:00. The blue wifi light on the dongle won't even flash after upgrade. After apt upgrade: root@odroidxu4:~# iwconfig enx001e06361f54 no wireless extensions. docker…

• 0

  Reputation Points

• 5 replies
• 5.2k views

Igor

September 17, 20224 yr

I’m running jammy and (I think) I’d like to upgrade to bullseye. But I can’t find a procedure for doing so. I’m guessing I can’t just dist-upgrade since jammy is Ubuntu and bullseye is Debian? I’ve googled for a procedure and searched this forum as well but I’m not finding a procedure. While searching this forum, I saw lots of topics where people had problems after upgrading to bullseye. Should I even do the upgrade? I don’t have much invested in the jammy install so far. Aside from running through armbian-config and getting all the settings the way I want them, the only things I’ve done are 1) installed Docker and 2) installed docker-compose. The latter was …

• 0

  Reputation Points

• 2 replies
• 10.1k views
• 1 follower

ErniePantuso

July 30, 20224 yr

Looking at various Docker images on Docker Hub, I see images for armv6, armv7, and armhf. Which are the right ones to use on an XU4/HC2?

• 0

  Reputation Points

• 2 replies
• 4.1k views
• 1 follower

MikeSmith

April 4, 20251 yr

Hi All, I'm a happy user of a Helios4, and have been for several years now. However, at some point it will be challenging to continue to support it, and I'd rather be proactive about maintaining access to my data than scrambling around. Do people here have recommendations on current hardware that can replace the Helios4? It would need to meet the baseline hardware requirements of the existing hardware. Bonus points if one can re-use the laser-cut case Thanks!

• 1

  Reputation Points

• 5 replies
• 5.9k views
• 2 followers

vortex375

August 2, 20233 yr

Hello everyone, I'm wondering if is possible to include in future releases of the Armbian Kernels these options: CONFIG_NETLABEL CONFIG_MPTCP CONFIG_NET_VRF CONFIG_OF_UNITTEST CONFIG_OF_DYNAMIC CONFIG_OF_OVERLAY CONFIG_INET_MPTCP_DIAG CONFIG_MPLS_ROUTING CONFIG_MPLS_IPTUNNEL CONFIG_NLMON CONFIG_NET_VRF CONFIG_GTP CONFIG_GENEVE CONFIG_IPVTAP CONFIG_IFB I'm playing around with my Odroid XU4 and I notice that I'm missing such options and drivers compiled in the Kernel. As an example Debian has these options enabled by default. In my case I created a script that is gett…

• 0

  Reputation Points

• 1 reply
• 3k views

Werner

July 1, 20224 yr

I've tried nand-sata-install on Armbian_22.05.3_Odroidxu4_jammy_current_5.4.199.img and Armbian_22.05.3_Odroidxu4_focal_current_5.4.199.img. Right at the end of running nand-sata-install there's an error. If I try to install anything after nand-sata-install it will hang or the SSD will go into read only mode. To be safe I tested various SD cards and USB to SATA controllers. sed: can't read /boot/boot.cmd: No such file or directory sed: can't read /boot/boot.cmd: No such file or directory Error while creating U-Boot loader image with mkimage umount: /mnt/nand-sata-install.wwpusQ/bootfs: not mounted.

• 0

  Reputation Points

• 3 replies
• 3.5k views
• 1 follower

sgjava

June 28, 20224 yr

Hello all! I used the following armbian image to write to an SD (I'm using an old odroid HC1 btw): https://armbian.site-meganet.com/dl/odroidxu4/archive/ I used the bullseye_current image that was there. On the main download page it says that the file for Odroid XU4 is compatible with HC1, HC2 and MC1. https://www.armbian.com/odroid-xu4/ My odroid HC1 boots ok but any attempt to use the built-in ethernet port results in an instant lock-up. Only way I can "get into" the device is with a USB ethernet adapter although even just issuing a command, eg ifconfig enx001e06366b84 192.168.1.99 locks everything up - even the USB e…

• 0

  Reputation Points

• 0 replies
• 2.8k views

ljones0

June 12, 20224 yr

System successfully upgraded. No problems detected (so far). Thanks to the team.

• 0

  Reputation Points

• 3 replies
• 3.3k views
• 1 follower

paulhart

October 15, 20223 yr

This is with armbian 22.02 bullseye. phross@helios4:~$ uname -a Linux helios4 5.15.26-mvebu #trunk.0002 SMP Thu Mar 3 10:15:53 UTC 2022 armv7l GNU/Linux phross@helios4:~$ cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: no or unknown cpufreq driver is active on this CPU maximum transition latency: 0.00 ms. analyzing CPU 1: no or unknown cpufreq driver is active on this CPU maximum transition latency: 0.00 ms. I remember reading discussions about issues with cpufreq patches causing issues on armada-38x socs. Is the cpufreq driver for armada-38…

• 0

  Reputation Points

• 1 reply
• 3.3k views

Heisath

May 22, 20224 yr

Hi, gotta ask a question Recently I just reinstalled all my XU4 based server from scratch. Brand new armbian Bullseye with OMV on top installed via armbian-config Then I noticed as seem bellow that half the cores (the low power ones) are idling, even when the system is fully under load on the high power cores The cores are enabled in the /sys/devices/system/cpu/cpuX/online files So the question is "what's wrong"? I don't have prints but I remember all the cores working before Thanks in advance Will

• 1

  Reputation Points

• 5 replies
• 4.4k views
• 1 follower

Will Santana

May 24, 20224 yr

Hi! my Odroid HC2 is running for more than three years now (24/7), hosting a nextcloud instance. Other than two preemptive SD-card swaps no maintenance necessary, armbian performs really great 🙂 Since I was thinking about upgrading to a better machine (Nano Pi M4, if they ever sell them again...) I wanted to install sysbench to compare some CPU specs. But sudo apt-get install sysbench gives: unable to locate package sysbench I'm running a recently upgraded armbian, v22.02.1 with Kernel 5.4.181. Any ideas? I'm pretty sure I had sysbench on an earlier version of armbian. EDIT: fixed typos

• 0

  Reputation Points

• 5 replies
• 5.7k views

berobispo

May 31, 20224 yr

Hello, I know that Kobol is out of Business.. But I am thinking...what if my helios4 motherboard die...? To mitigate that, I want to acquire new motherboard. Does any one knows how I could get one? Thanks in Advance

• 0

  Reputation Points

• 1 reply
• 2.7k views

Werner

May 15, 20224 yr

Hi, I have a Armbian 22.02.1 with Linux 5.10.60-mvebu with buster debian packages. Its possible to update bullseye a not lost my storage raids?

• 0

  Reputation Points

• 2 replies
• 4.2k views

Heisath

May 15, 20224 yr

Odroid XU4 / Armbian 22.02 Bullseye USB3 sata drive gets randomly disconnected: (every 8 hours or so when constantly reading / writing) [44676.709229] sd 0:0:0:0: [sda] tag#24 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN [44676.709252] sd 0:0:0:0: [sda] tag#24 CDB: opcode=0x28 28 00 49 a5 1b d8 00 00 08 00 [44681.728962] xhci-hcd xhci-hcd.8.auto: xHCI host not responding to stop endpoint command. [44681.749158] xhci-hcd xhci-hcd.8.auto: xHCI host controller not responding, assume dead [44681.749210] usb 4-1.2: cmd cmplt err -108 [44681.749509] xhci-hcd xhci-hcd.8.auto: HC died; cleaning up [44681.749696] usb 3-1: USB disconnect, device numbe…

• 0

  Reputation Points

• 2 replies
• 4.2k views
• 1 follower

j-be

October 30, 20223 yr

Hi, I have been running Armbian Buster on an Odroid HC1 for a while but today one upgrade is held back: The following packages have been kept back: libc-dev-bin 0 upgraded, 0 newly installed, 0 to remove and 31 not upgraded. This is why: $ sudo apt install libc-dev-bin Reading package lists... Done Building dependency tree Reading state information... Done The following package was automatically installed and is no longer required: linux-libc-dev Use 'sudo apt autoremove' to remove it. Recommended packages: manpages manpages-dev The following packages will be REMOVED: armbian-config build-essential g++ g++-8 libc6-dev libstdc++-8-dev…

• 0

  Reputation Points

• 1 reply
• 3.5k views

Rob van der Linde

April 2, 20224 yr

Hi all, I got my helios4 sometimes in 2019 and it was one of the best purchases I ever made. It has served and was solid as a rock. Unfortunately all that ended couple of days ago when I noticed the Helios was not powering up properly, think it was the power supply not connected well (because I just recently changed the location) I removed and fitted the PSU a couple of times, I could see the led light come on but still it would not boot properly. By the time I found out what the real problem is things had gone worse, the reason for the incomplete boot was the SD card has been removed. Unfortunately, it seems my constant removing and refitting the PSU to …

• 0

  Reputation Points

• 1 reply
• 3.1k views
• 2 followers

TRS-80

March 31, 20224 yr

4 2.5" HDDs. [ 1242.509097] BTRFS info (device sda): scrub: started on devid 1 [ 1242.560838] BTRFS info (device sda): scrub: started on devid 4 [ 1242.615578] BTRFS info (device sda): scrub: started on devid 3 [ 1242.703587] BTRFS info (device sda): scrub: started on devid 2 [ 3731.573257] ata2.00: exception Emask 0x0 SAct 0xffffffff SErr 0x0 action 0x0 [ 3731.573272] ata2.00: irq_stat 0x40000001 [ 3731.573279] ata2.00: failed command: READ FPDMA QUEUED [ 3731.573283] ata2.00: cmd 60/80:00:00:2f:2b/00:00:03:00:00/40 tag 0 ncq dma 65536 in res 41/40:d8:30:e2:f6/00:00:05:00:00/40 Emask 0x9 (media error) [ 3731.573300] ata2.00: status: { D…

• 0

  Reputation Points

• 0 replies
• 2.2k views

Mangix

March 12, 20224 yr

I'm using Armbian 21.08.8 (Bullseye). I want to upgrade to Armbian 22.02.1 but "apt-get update" doesn't offer anything. Reason seems to be that <mirror>/apt/dists is from Feb 1st 2022. OTOH <mirror>/dl contains the new release but "starting from scratch" (download image, write SDcard) implies that I have to rebuild my OMV6 on top of Armbian. Question: When can I expect that <mirror>/apt/dists will be refreshed? Or is there any other way to upgrade my installation?

• 0

  Reputation Points

• 16 replies
• 11.5k views
• 1 follower

rayc

June 13, 20233 yr

If I boot my Odroid XU4 without the HDMI cable connected, my HDMI display does not work. If I boot with the HDMI cable and monitor connected, the HDMI display works fine even if it is disconnected and reconnected. I am running debian buster. deb http://deb.debian.org/debian buster main contrib non-free I have compared the dmesg output from when HDMI works and does not work and do not see a difference. In case it helps, here are all of the dmesg lines with HDMI in them. root@odroidxu4:~# grep -i hdmi dmesg_hdmi_works_usb_hdmi_plugged_in_at_boot.txt [ 0.000000] Kernel command line: console=ttySAC2,115200n8 console=tty1 co…

• 0

  Reputation Points

• 0 replies
• 3.2k views

Michael Schuh

February 6, 20224 yr

I was trying get sys-oled running on a new installation (upgrade, really) of bullseye. If go with the original Kobol github version, https://github.com/kobol-io/sys-oled, it fails to build RPI.GPIO and something else. I also found an alternate at https://github.com/rpardini/sys-oled-hc4, that builds, but when I run it, it complains about a thermal call in python: # sys-oled --display sh1106 Traceback (most recent call last): File "/usr/local/bin/sys-oled", line 142, in <module> main() File "/usr/local/bin/sys-oled", line 132, in main display_info(device) File "/usr/local/bin/sys-oled", line 105, in display_info draw.text(…

• 0

  Reputation Points

• 3 replies
• 3.3k views
• 2 followers

TRS-80

February 26, 20224 yr

I tried updating my kernel to self-built 5.4.173 as usual. I got some errors during installation due to low space on /boot, but after removing leftovers of 5.4.168 the installation worked as expected. Something went wrong though, as my HC1 no longer boots. This is shown via UART: All the files seem to be on the SD card: $ ls -l insgesamt 32447 -rw-r--r--. 1 root root 64 8. Jan 16:27 armbianEnv.txt -rw-r--r--. 1 root root 0 6. Sep 2019 armbianEnv.txt.out -rw-r--r--. 1 root root 1536 29. Mai 2018 armbian_first_run.txt.template -rw-r--r--. 1 root root 38518 29. Mai 2018 boot.bmp -rw-r--r--. 1 root root 4882 29. Mai 2018 boot-desktop.p…

• 1

  Reputation Points

• 39 replies
• 13.8k views

belegdol

June 17, 20224 yr

Hello, I have recently upgraded OMV to version 6 and armbian to bullseye alongside it: https://forum.openmediavault.org/index.php?thread/41361-odroid-hc1-armbian-update-report/ Since the upgrade, I am getting daily emails from armbian-truncate-logs with the following content: Spoiler [0;1;38;5;185mJournal file /var/log/journal/1ded17e370994bc2bfab08257042ce4c/user-1000@8682aaf9b65f4db593fdb2f01a8b3fbc-0000000000000501-0005d513e7226c26.journal is truncated, ignoring file.[0m Deleted empty archived journal /var/log/journal/1ded17e370994bc2bfab08257042ce4c/system@0005d52e63fd8387-4776da5b1e9dd6f3.journal~ (4.0K). Deleted empty archived jo…

• 0

  Reputation Points

• 12 replies
• 6.2k views
• 2 followers

Trillien

November 11, 20223 yr

armbianEnv.txt is missing from latest XU4 focal image Armbian_21.08.5_Odroidxu4_focal_current_5.4.159_minimal.img. Should I just create on or use boot.ini?

• 0

  Reputation Points

• 0 replies
• 2.2k views

sgjava

January 2, 20224 yr

Hello! I have connected the WD 10TB RED HDD via external USB 3.0 enclosure to one of the USB 3.0 Ports on the HELIOS4. Unfortunately the speeds don't exceed 45 MB/s. when running RSYNC jobs. On the PC I can completely use the speed of the GBit Port.. When connected to the USB Ports of HELIOS4 the speeds are low. Can somebody help? The external enclosure is from UGREEN. HDD is NTFS formatted. Any advice will be gratefully appreciated.

• 0

  Reputation Points

• 0 replies
• 2.6k views

Vodalex

December 5, 20214 yr

Wanted to share my unfortunate experience today of trying to do a fresh install of a newer armbian version in order to accommodate OMV 5 on my Helios4. Was doing everything as usual and after the first boot from the new SD card tried to run armbian-config while still attached to the serial console. That proved to be a mistake as it started some auto install script type of thing and wiped one of my hard drives. Also the GUI wasn't showing properly. The exact same thing happened when I tried to reproduce the same steps. Should have been wiser and connected via SSH after inital boot to go from there. No such thing happened when running armbian-config via SSH for the first ti…

• 0

  Reputation Points

• 0 replies
• 2.2k views

mxr

November 28, 20214 yr

The board was up and running when suddenly I could not access the share anymore. I went near it and I was hearing some HDD clicking. I rebooted it from the console and when it came on, no storage was available. I could see some /dev/sd* but one HDD was missing from it and the lvm was not available anymore. Also all the HDDs where clicking and I was hearing a loud buzzing sound from the board. I rebooted it again, measured the PSU and even load tested it and it is fine, the same for the moled connectors, it was measuring 12V and 5V, but the truth was, the HDDs this time were not even detected. Took it all apart and booted it without any HDD connected and sur…

• 0

  Reputation Points

• 4 replies
• 3k views
• 2 followers

vspeed

March 28, 20224 yr

Hello all, This seems to be an issue related to the python script to start the program, any help will be appreciated for those with python programming understanding: $ sudo systemctl status sys-oled.service * sys-oled.service - System Starting on OLED Display Loaded: loaded (/etc/systemd/system/sys-oled.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2021-09-17 02:22:42 JST; 10s ago Process: 4425 ExecStart=/usr/bin/python3 /usr/local/bin/sys-oled --display ${display_model} (code=exited, status=1/FAILURE) Main PID: 4425 (code=exited, status=1/FAILURE) Sep 17 02:22:42 nas python3[4425]: main() Sep 17 02:22:…

• 0

  Reputation Points

• 3 replies
• 3.6k views

quincybatten

February 13, 20233 yr

Hi there, I have a little problem with my i2c-screen on the Helios4. It was setup according to the Kobol-Wiki and was working right from the start. However after running for some time (in this example it took around 6 hours) the screen is black and empty. Once I SSH back into the helios and restart the systemd sys-oled.service, it works again for some time... "journalctl -u sys-oled.service" gives the following: Sep 13 10:18:38 helios4 systemd[1]: Started System Starting on OLED Display. Sep 13 16:46:01 helios4 python3[23009]: Traceback (most recent call last): Sep 13 16:46:01 helios4 python3[23009]: File "/usr/local/bi…

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

m4110c

September 13, 20215 yr

Hello, few days ago I did apt upgrade of my armbian system on Odroid HC2 and there was a reboot req cause of new kernel, so I did reboot it. It wont boot with this error (sorry for missing letters, my LCD is not able to reposition the screen output, attached usb kbd is not working, dont know why, so I just took a pict by my phone): h to partitions #0, OK is current device ing mmc 0:1... /boot/extlinux/extlinux.conf eving file: /boot/extlinux/extlinux.conf ytes read in 2 ms (149.4 KiB/s) Armbian eving file: /boot/uInitrd 776 bytes read in 782 ms (20.2 MiB/s) eving file: /boot/Image d to load '/boot/Image' ing Armbian for failure retrieving kernel T FAILED: con…

• 0

  Reputation Points

• 3 replies
• 4.2k views
• 1 follower

VictorC

September 9, 20215 yr

As far as I can see on odroid wiki for the lcd and fan enabling the links leads to ubuntu files. I want to install latest armbian for odroid xu4q board and omv5 so I'm wondering if I can use these files or do I need some other files to enable lcd and fan on cloudshell2 + odroid xu4q and armbian?

• 0

  Reputation Points

• 3 replies
• 3.9k views
• 1 follower

Igor

August 30, 20215 yr

Hi, I froze kernel to Linux 4.14.222-odroidxu4 as my Odroid-HC1 couldn't be sometime reach with ssh when updating kernel. I get that after reboot and doing apt update, N: Ignoring file '02-armbian-periodic.distrib' in directory '/etc/apt/apt.conf.d/' as it has an invalid filename extension This file is apparently created again as I remove it each time. Laurent

• 0

  Reputation Points

• 3 replies
• 3.6k views

emk2203

October 17, 20214 yr

I had to reinstall on my Linux desktop due to a hard drive failure. I copied the mounting language in my /etc/fstab file and now it times out on mounting. This is my mounting entry which worked fine before 192.168.0.123:/mnt/md0 /mnt/RAID nfs rw,_netdev,hard,intr,rsize=8192,wsize=8192,timeo=14,user 0 0 That used to work. I made no changes to my Helios4. When I try to mount it manually, this is what I get: mount -av mount.nfs: timeout set for Fri Jul 23 07:26:16 2021 mount.nfs: trying text-based options 'hard,intr,rsize=8192,wsize=8192,timeo=14,vers=4.2,addr=192.168.0.123,clientaddr=192.168.0.2' mount.nfs: mount(2): Connection refused mount.nfs: tryi…

• 0

  Reputation Points

• 6 replies
• 4.7k views
• 1 follower

Werner

July 26, 20215 yr

Hello Everyone, My Helios4 stop of working. It was probably SD CARD because I format an other one with the last Armbian and after it boot again. Now I config ip address and can connect to it via ssh. Install webmin and saw that it didn't mount /dev/md0 I did it but filesystem in raid1 is btrfs. When I mounted it it say : unknown filesystem type 'LVM2_member' Someone can help me? Best regards.

• 0

  Reputation Points

• 2 replies
• 3.3k views

Stéfan Basch

July 15, 20215 yr

Hi, after some time on storage i tried to reativate my batch 2 helios4 only to be greeted with a seemingly broken device. Tried the following: 1. Flashed a new good SD Card with Armbian (golden sundisk one) 2. unplugged all harddisks in my helios 4 3. inserted SD-Card and plugged in in. Result: Orange blinking on the Network Port Green blinking next to the Power slow USB-TTY does not show up Tt does not boot I hear a slight chirping noise synchronous with the green LED. It comes directly from the board not the fans, harddisks or PSU. Sounds like a fan briefly rubbing against something but it's comming 100%…

• 0

  Reputation Points

• 2 replies
• 3.5k views
• 1 follower

Nathan Driver

July 6, 20224 yr

Hello the Helios4 community, This is quite the story and I may have messed up at multiple steps, especially since I did not backup my RAID data (please don't go too hard on me for this, it's difficult task for me since I don't have enough space on any of my computer to do so), but I hope that at least you can help me to salvage some data. Short story: I flashed my sd cart to upgrade to the last armbian available (I was on armbian 9) After some hurdle I finally could had a stable boot and installed OpenMediaVault When looking for my RAID 10 data I found that they were gone, replaced by what looks like a linux system, here's its current content…

• 0

  Reputation Points

• 0 replies
• 3.4k views
• 1 follower

Hrist

June 22, 20215 yr

Fresh-builded armbian image, Helios4. Try to enter armbian-config → system → cpu root@helios4:~# cat /etc/os-release NAME="Ubuntu" VERSION="21.04 (Hirsute Hippo)" ID=ubuntu ID_LIKE=debian PRETTY_NAME="Armbian 21.08.0-trunk Hirsute" VERSION_ID="21.04" HOME_URL="https://www.ubuntu.com/" SUPPORT_URL="https://help.ubuntu.com/" BUG_REPORT_URL="https://bugs.launchpad.net/ubuntu/" PRIVACY_POLICY_URL="https://www.ubuntu.com/legal/terms-and-policies/privacy-policy" VERSION_CODENAME=hirsute UBUNTU_CODENAME=hirsute

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

iav

June 15, 20215 yr

Hi all, My Hard Drive in my HC2 is not found or not readable. Before I was on Armbian Buster with Kernel 4.14 and everything was working fine. I switched and am now running Armbian Focal 21.05.2 with Kernel 5.4.116 . HDD is btrfs formatted. /proc/filesystems lists btrfs so this is not the problem. /dev/sda exists, but sda will not be listed when I lsblk. Dmesg shows a Read Capacity(16) failed. Not posting the whole dmesg log b/c armbianmonitor is attached. Grateful for any help or hints =)

• 0

  Reputation Points

• 2 replies
• 3.8k views
• 1 follower

MowTee

June 17, 20215 yr

Howdy, I'm running Armbian_21.05.1_Odroidxu4_focal_current_5.4.116.img on my XU4 for security cameras. It averages about 60 Mbps 24/7. After a couple days usually one adapter disappears (from ip a and nmtui) and sometimes both (I have a USB 1 Gbps adapter too). I'm not seeing anything in the logs to indicate an error. I monitor this system with Zabbix and I see no unusual activity before this happens. Is there a way to get diagnostics for this event?

• 1

  Reputation Points

• 9 replies
• 5.7k views
• 1 follower

sgjava

June 27, 20215 yr

Hello, i saw a post regarding ZFS > zfs What is the current state of ZFS support? Is it a stable to run ZFS as FS for root fs only on SD card (16-32GB)? I need that for an easy backup on FS level using send/rec commands. But as we know xu4 is 32bit only - > maybe problem with stability - stability 32bit official solution but for rpi4 Or maybe is there a point to use zfs for root fs at all? what about LMV? thanks

• 0

  Reputation Points

• 2 replies
• 4.1k views

Igor

June 5, 20215 yr

.

• 0

  Reputation Points

• 0 replies
• 3.1k views

dolphs

May 26, 20215 yr

Hello, HELIOS4 system was running (and doing nothing), when it suddenly crashed. After restart, nothing automatically loaded (system stuck in emergency mode), once USB cable plugged i managed to log only once into the system, and discovered that no disks where mounted anymore (not even available / detect by the board) (it's not so easy as it seems there are some freezes, maybe due to the hardware errors related to he missing hdd links) 13:00 root@helios4 ~# ll /dev/sd* zsh: no matches found: /dev/sd* Is this a failing PSU (like in other threads) ? To be noted : the PSU has a blinking green light ... i can't rememb…

• 0

  Reputation Points

• 3 replies
• 3.9k views
• 1 follower

SR-G

June 2, 20215 yr

Hello, I stripped two or three mounting screws for the board. Does anyone know what is the type of these screws and what size are they? Thanks

• 0

  Reputation Points

• 0 replies
• 2.7k views

strike_noir

May 22, 20215 yr

Hi, I am using Nextcloudpi Image (Armbian) on an HC1. This setup is obviously not booting anymore after system upgrade. Packages that have been upgraded: - armbian-config - armbian-firmware - linux-buster-root-legacy-odroidxu4 - linux-dtb-legacy-odroidxu4 - linux-image-legacy-odroidxu4 - linux-u-boot-odroidxu4-legacy Insterting the µSD into an Laptop running PureOS (Debian fork) I can access log files. I could investigate so far, that there was a system upgrade (armbian-firmware_21.05.1) on 2021-05-11 6:00 am. After that a message that system will be rebooted on 2021-05-12 4:00 am. That actually happened. I can see this in several log…

• 0

  Reputation Points

• 6 replies
• 7.7k views

marsch

June 3, 20215 yr

After latest upgrade 21.05.01 apt says linux-buster-root-current-odroidxu4 is obsolete now and could be removed with autoremove. But even this version was installed with same upgrade, so i wonder why it should be removed now? Should i really remove that package? Thx

• 0

  Reputation Points

• 2 replies
• 3.8k views
• 1 follower

nihilista

May 15, 20215 yr

@gprovost I described last year a process to upgrade from omv4 to omv5. (which is doable). I also did a clean install of omv5 after i was having random reboot issues using the newer kernel5. I ended up using the clean built and reconfiguring all the services and dockers. I do not recommend using the newer kernel if you are using dockers. This is where I would have random system reboots. OMV4 was very stable but since omv4 was eol. I decided to upgrade or do a clean install. I did both with the same random reboots using the newer kernel 5. Once i switched back to the older kernel with my config, I was not having the random reboot issues. I understand this would be ha…

• 0

  Reputation Points

• 0 replies
• 2.9k views

PEW

May 13, 20215 yr

Hi, First using my Helios4 after I left her in my storage room. I have installed and running open media vault. I sometimes wanted to shutdown the NAS. I shutdown using sudo poweroff. Is the a soft method to turn it on again? I currently turn it on using the power switch. Regards,

• 0

  Reputation Points

• 2 replies
• 3.8k views
• 1 follower

Werner

May 12, 20215 yr

I'm running a Helios4 NAS with OMV 5.6.6-1 and ZFS 2.0.3. After running for approximately a week it becomes unresponsive - OMV login shows a blue screen but doesn't get to login page, SSH timeout and serial login just keeps going back to the login prompt without asking for the password. Repowering the unit (physically disconnecting the power because there is no way to shut it down gracefully) brings it back to life and it runs again for a week or so before the same thing happens again. I'm not quite sure where to start troubleshooting this. Any ideas ?

• 0

  Reputation Points

• 5 replies
• 4.2k views

SymbiosisSystems

June 9, 20215 yr

Hi, Using 4 HDDs in my Helios 4 with Openmediavault 5.5. After a update & restart all the HDD's are gone (not shown at all in lsblk anymore). After poking around in the the systemmessages i found this in dmsg, but don't know what to do with it. ``` [ 1.746837] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 1.746909] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 1.747062] platform f10a8000.sata:sata-port@0: supply target not found, using dummy regulator [ 1.747207] platform f10a8000.sata:sata-port@1: supply target not found, using dummy regulator [ 1.747285] ahci-mvebu…

• 1

  Reputation Points

• 3 replies
• 4k views
• 1 follower

FredK

April 23, 20215 yr

Hello everyone, I am thinking about moving the Helios4 into a Inter-Tech SC-4100 case. The backplane in that case has only one Molex powerconnector. So is it possible to combine both power connectors on the board (J14 + J19) into one ? https://wiki.kobol.io/helios4/img/hardware/board_legend.jpg Thanks Br, Joe

• 0

  Reputation Points

• 2 replies
• 3.4k views
• 1 follower

DocViper

April 7, 20215 yr

Anyone know why it's not supported out of the box? The wiki provides a patch but does not mention why it's not upstream or in Armbian. The bus-width being 4 is also quite suspect. All the other Armada 38x devices have it at 8. Armada 37x ones have it at 4.

• 0

  Reputation Points

• 5 replies
• 4.5k views
• 1 follower

m4110c

September 9, 20215 yr

Following the install instructions from: https://www.wireguard.com/install/#debian-module-tools Wireguard server is working correctly as I have other devices working. I recieve the following output: root@helios4:/etc/wireguard# wg-quick up PiVPNHelios4 [#] ip link add PiVPNHelios4 type wireguard [#] wg setconf PiVPNHelios4 /dev/fd/63 [#] ip -4 address add 10.6.0.5/24 dev PiVPNHelios4 [#] ip link set mtu 1420 up dev PiVPNHelios4 [#] resolvconf -a tun.PiVPNHelios4 -m 0 -x Unknown interface 'tun': No such device [#] ip link delete dev PiVPNHelios4 Have I setup something wrong with wireguard? or is it not fully supported? …

• 1

  Reputation Points

• 4 replies
• 22.4k views
• 2 followers

Declan

March 15, 20215 yr

After switching from Debian Buster (installed via Petitboot) to Armbian, I have problems with NFS on Openmediavault that didn't exist the weeks before. My NFS streams abort after a few minutes, sometimes seconds (on Libreelec as well as Kodi for Windows). In OMV it shows me that the service is enabled and running, but systemctl says: nfs-server.service loaded active exited. With exportfs -rav it runs again, only to stop after a few minutes. It also works without command if I wait a few minutes. I also did a fresh install of Armbian, wich did nothing.

• 0

  Reputation Points

• 2 replies
• 3.5k views
• 1 follower

Igor

March 2, 20215 yr

Hi all, I'm running a couple of ODroid XU4's as a server. Yesterday I ran an update and after this update the board no longer boots... (I was running Armbian Focal kernel 4 I have tested a 'fresh' armbian image and then the system boots without issues. I have saved what packages are updated and wonder if I would be able to restore this somehow? A log of the update (never mind the dutch) https://pastebin.com/WWP2DFfC I used to have kernal 5.4 on this board, but I downgraded about 6 months ago. Could that be the issue? Because in the log I read: Uitpakken van .../77-linux-image-current-odroidxu4_21.02.2_armhf.deb wordt …

• 0

  Reputation Points

• 1 reply
• 5k views

Igor

February 16, 20215 yr

Is helios4 usb gadget Ethernet enabled? If it is available, how can it be activated? If the usb gadget Ethernet is not default build , which helios4 kernel build options should I modify?

• 0

  Reputation Points

• 1 reply
• 3.1k views

aprayoga

February 15, 20215 yr

Hello, I tried to use again my Helios4, but when we put the power on, only the LED8 light up. This Helios4 was working great a few month ago (before we receive the Helios64 :-) So we removed all sata cables (and fan, and power cables for hard drives) to made new tests. But still the same...:-( And the processor is hot. So, if someone have a idea to fix it. Thank you. Regard.

• 1

  Reputation Points

• 3 replies
• 4.1k views
• 1 follower

pierre

February 17, 20215 yr

Let me ask a question in a armbian-forum where I found up til now no solution. After updating nextcloud to 20.0.5 (now I use 20.0.7) I get the following warning in OMV5 Settings->Overview: Asking thas question in the OMV-forum I received the following answer from the user "Morlan": A missing MariaDB docker version 10.2ff could be a show-stopper if nextcloud v21 will be available for Helios4.

• 0

  Reputation Points

• 7 replies
• 5.9k views
• 1 follower

FredK

February 11, 20215 yr

I have a Helios4 (2nd batch) with 4 HDDs, and before I started using it, I decided to test its performance on the planned workload. However, I got quite not satisfied with the numbers. First, the SSH speed is about 30 MB/s, while the CPU core where sshd runs is at 100% (so I suppose it's the bottleneck). I create a sparse file and copy it over SSH: helios4# dd if=/dev/null bs=1M seek=2000 of=/tmp/blank With scp I get up to 31.2 MB/s: pc# scp root@helios4:/tmp/blank /tmp With rsync I get pretty much the same numbers: pc# rm /tmp/blank pc# rsync -e ssh --progress root@helios4:/tmp/blank /tmp/ blank 2,097,152,000 100% 31.06MB/s 0:01:04 (xfr…

• 1

  Reputation Points

• 12 replies
• 7.2k views
• 2 followers

Heisath

February 16, 20215 yr

I can't pinpoint the cause of the freeze exactly, but it shows as follows in syslog: At midnight, logrotate was started but never successfully concluded. At the time, I was also recording a stream via smb to the hdd. (Not a very demanding activity) When I tried to access the SBC via network share or ssh this morning, neither would show as available. The SBC was running but "dead". When I rebooted it by re-plugging power, instead of showing ~9:00 o'clock, the SBCs internal clock showed 02:17. Here are the last messages of the syslog before the SBC locked up: I should note that the SBC has been running 24/7 stable for weeks. …

• 0

  Reputation Points

• 0 replies
• 2.9k views

Thule

January 17, 20215 yr

armbianmonitor -u: http://ix.io/2Lae Did an apt update/upgrade & reboot today, and the system came back up but none of the drives did. Imaged a new SD card with stock armbian, and still no luck. Measured the voltage of the PS (at the plug, not the molex connector) at 12.3v Anything else I can check/try?

• 1

  Reputation Points

• 6 replies
• 4.1k views
• 1 follower

devman

January 13, 20215 yr

Hi, please, which core are You using on odroid HC2? I am running on HC2 only openmediavault, but i will try nextcloud in the docker - which core image is better for?

• 0

  Reputation Points

• 1 reply
• 3.8k views
• 1 follower

Werner

January 7, 20215 yr

Hi, I've got since several days an issue with armbian-truncate-logs. I received mail alerts from cron as this one, error: error running shared postrotate script for '/var/log.hdd/mysql/mysql.log /var/log.hdd/mysql/mysql-slow.log +/var/log.hdd/mysql/mariadb-slow.log /var/log.hdd/mysql/error.log ' error: error running shared postrotate script for '/var/log.hdd/nginx/*.log ' How to debug that? Laurent

• 0

  Reputation Points

• 3 replies
• 4.3k views

Guest

January 1, 20215 yr

Hi, I am opening a new topic to make things clearer. This is a follow-up post from here: After managing to install it, I moved my Helios 4 and switched it on again. It started to work but then it shut down. I cannot switch it on anymore. I don't know if it comes from the Power supply or the motherboard. What are the solutions? Thank you for your help.

• 1

  Reputation Points

• 2 replies
• 3.6k views
• 1 follower

GeckoX

December 21, 20205 yr

Hello, So I am trying to setup my Helios 4. I am running into some issues with the installation, trying to group them here, so it will be easier. 1. I am trying to setup NextCloud following your tutorial on kobol wiki but I cannot install PHP 7.3 Here is the screenshot of the output after running the command: 2. Also, when I enter Armbian-Config, it seems unstable and crash. The menu doesn't display. 3. Other issue, I cannot access my NAS through SSH. It returns "operation timed out" How to solve these issues? Thank you for your help.

• 1

  Reputation Points

• 9 replies
• 6.5k views
• 3 followers

gprovost

January 7, 20215 yr

I've been using a Helios4 for nearly 2 years now and it's been fantastic. A couple days ago, it stopped working though. The serial console revealed a boot loop at "U-Boot SPL" and only showing the disks, but never attempting to boot the OS. I did some forum searching and discovered the PSU could be the issue. Using a multimeter, I tested the PSU pins and I get the following (see diagram): PIN 1: +2.66V (fluctuates between 2.64-2.66) PIN 2: +2.66V (fluctuates between 2.64-2.66) PIN 3: GND PIN 4: GND What are the voltages that Helios4 expects for these pins? Should both 1 & 2 be 12V or should one be 12V and the other 5V? I already …

• 1

  Reputation Points

• 2 replies
• 4.3k views
• 3 followers

gprovost

December 18, 20205 yr

OK, so while documenting the Armbian patch process I needed something actual to patch. I added gpio-line-names to the device tree, so now all lines are defined. Once I finish the documentation I'll PR this patch. No more guessing what physical pin is! At some point it might make sense to put in jumper and physical pin #. Spoiler gpioinfo gpiochip0 - 8 lines: line 0: "GPY7.0" unused input active-high line 1: "GPY7.1" unused input active-high line 2: "GPY7.2" unused input active-high line 3: "GPY7.3" unused input active-high line 4: "GPY7.4" unused input active-high …

• 1

  Reputation Points

• 2 replies
• 4.6k views
• 1 follower

sgjava

December 13, 20205 yr

DUring a fresh install of Debian buster recently, I went through the armbian-config setup, which finished with "install a whole lot of package updates, and update the boodloader." Since I've rebooted from that, the board no longer boots. It's been a while, so I have unfortunately forgotten the details of what actually happened. I didn't expect that set of updates to change anything in the firmware, only the OS and u-boot on the MMC-card. The board powers on, attempts to boot from the MMC and then bails. This is the error log: (slightly trimmed) I've tried several different MMC cards. I've tried booting from SPI, SATA and UART…

• 1

  Reputation Points

• 11 replies
• 6.8k views
• 5 followers

Renée

January 9, 20215 yr

As the title states I already have software raid setup on my NAS. I'm currently running OMV 4 and I'd like to do a fresh install of the latest Debian image and OMV 5. I do not want to lose my data and would like to simply re-mount my drives. Is this possible? Also if I mess up and I'm unable to mount the raid/volumes, could I create an image of my current micro sd card and simply reflash it back onto the card and have everything as it was?

• 1

  Reputation Points

• 4 replies
• 7.1k views
• 1 follower

helios4noob

May 12, 20215 yr

Is it me or it the mv_xor driver being loaded late? ``` [ 0.007976] xor: measuring software checksum speed [ 0.164062] xor: using function: arm4regs (2534.000 MB/sec) [ 0.316068] raid6: neonx8 xor() 1096 MB/s [ 0.452063] raid6: neonx4 xor() 1378 MB/s [ 0.588069] raid6: neonx2 xor() 1610 MB/s [ 0.724066] raid6: neonx1 xor() 1346 MB/s [ 0.860075] raid6: int32x8 xor() 328 MB/s [ 0.996072] raid6: int32x4 xor() 369 MB/s [ 1.132082] raid6: int32x2 xor() 332 MB/s [ 1.268063] raid6: int32x1 xor() 285 MB/s [ 1.268067] raid6: .... xor() 1610 MB/s, rmw enabled [ 1.665163] mv_xor f10608…

• 0

  Reputation Points

• 3 replies
• 3.3k views
• 2 followers

Mangix

December 14, 20205 yr

So I tried switching my MMIO GPIO to /dev/gpiomem from /dev/mem and it doesn't appear to support the GPZ block https://wiki.odroid.com/odroid-xu4/hardware/expansion_connectors#con_11_-_2x6_pins The address is 0x03860000. Hard Kernel's wiringPi doesn't seem to support this either. Should this be a question I ask Hard Kernel folks? https://wiki.odroid.com/odroid-xu4/software/gpio_register_map

• 0

  Reputation Points

• 1 reply
• 3.2k views
• 1 follower

sgjava

December 6, 20205 yr

Dear Readers I had quite some troubles migrating my armbian system from an SD-Card (16GB) to my emmc (32GB). I'd like to sum up my journey for future travelers ;-) I was not successful simply copying the image of the sd to the emmc and resizing the partition. It would not boot. Apparently emmc has additional boot partitions which must be set correctly. I "repaired" the emmc with this https://wiki.odroid.com/accessory/emmc/recovery_xu4 and it booted Android all right from emmc. I then rebooted on my SD-Card and used the nand-sata-install command to "Boot from eMMC - system on eMMC". It took some time to copy, but when booting on the emmc, still Android…

• 0

  Reputation Points

• 1 reply
• 7.4k views
• 1 follower

TRS-80

December 1, 20205 yr

I have an array of HC2's running lizardfs. The other units are running 5.4.72-odroidxu4 kernels, but I dared to upgrade one to 5.8.16-odroidxu4 Only this one unit threw a Since the other units didn't I show anything in their logs, I have to assume it isn't because a process running away or a memory leak. line of fstab to mount the spinning rust drive: UUID=be95e207-1768-4fd9-bda9-ddc126a47d50 /chunks/be95e207-1768-4fd9-bda9-ddc126a47d50 xfs rw,noexec,nodev,noatime,nodiratime,largeio,inode64 0 2 Can't think of any additional info that would be useful. If someone has suggestions, i would be interested.

• 0

  Reputation Points

• 1 reply
• 3.2k views
• 1 follower

Werner

November 21, 20205 yr

Where can I buy Helios4? Are you still planning to sell it? Helios64 is too expensive honestly and since OpenWRT supports this device.

• 0

  Reputation Points

• 2 replies
• 4k views
• 1 follower

TRS-80

November 20, 20205 yr

I seem to have issues on my Helios 4 where it constantly reboots. I have no idea what happens just before. I assume some kind of kernel panic. Kernel 4.19.63 - works 4.19.84 - I believe works 4.19.104 and above - broken Newer ones are broken as well. This is most likely an issue with some local patch. Any way to view the history?

• 1

  Reputation Points

• 78 replies
• 23.2k views
• 4 followers

Mangix

December 20, 20205 yr

Just doing maintenance tonight on my boxen, regular `apt upgrade && apt update` on ODROID-XU4 and I noticed Debian upgraded to latest kernel (5.8 or whatever). I go look in boot and notice `uInitrd' is pointing at the new Debian version (instead of Armbian version): drwxr-xr-x 4 root root 4096 Nov 15 19:53 . drwxr-xr-x 22 root root 4096 Nov 15 19:50 .. -rw-r--r-- 1 root root 65 Nov 15 19:28 armbianEnv.txt -rw-r--r-- 1 root root 1536 Jun 4 15:24 armbian_first_run.txt.template -rw-r--r-- 1 root root 38518 Jun 4 15:24 boot.bmp -rw-r--r-- 1 root root 4882 Jun 4 15:24 boot-desktop.png -rw-r--r-- 1 root root 12479 Jun 4 …

• 0

  Reputation Points

• 2 replies
• 3.4k views
• 1 follower

TRS-80

November 17, 20205 yr

Hello For quite some time I experienced system freezes. I already measured the voltage on the board 12V and 5V are okay on both connectors. Attached you will find the armbianmonitor -U output. I tried to capture kernel logs using information from some other thread. sudo dmesg -n 7 sudo dmesg -w But I could not capture anything useful. Today the system froze while checking the raid (filesystem was not mounted). [ 168.224361] md: data-check of RAID array md0 Is there anything else I can do to shed some light? Thanks and regards -kratz00 armbianmonitor.log

• 1

  Reputation Points

• 34 replies
• 13.8k views
• 5 followers

Mangix

February 6, 20215 yr

News related to Helios4 : Software update Wiki / Documentation update Etc...

• 0

  Reputation Points

• 1 reply
• 3.3k views
• 1 follower

gprovost

November 12, 20205 yr

Hello I am wondering if there is a way to get the screen that comes with the OGST to work on Armbian?

• 0

  Reputation Points

• 0 replies
• 2.6k views

johnnyde94

November 9, 20205 yr

Hi, i have odroid HC2 with up-to-date armbian (kernel 4.something - i am not at home, i do not remember its version) I have issues with samba speed - before last minority update it was 115/110 MB/s (read/write) now it is 100/90 with cifs mount in arch linux and 60/60 in Windows 10. Cables, router - everything is untact and still the same cpu governor is on demand, samba is installed over OMV, htop shows max 10%, ram the same where can be the problem?

• 0

  Reputation Points

• 0 replies
• 3.1k views
• 1 follower

Romeo

October 29, 20205 yr

Hi, I have recently installed armbian-config on my HC1 running OMV and switched to -current kernel from -legacy. Unfortunately, now whenever I soft-reboot following a kernel update, the sda drive is missing: [ 6.161366] usbcore: registered new interface driver usb-storage [ 6.180240] scsi host0: uas [ 6.181260] usbcore: registered new interface driver uas [ 6.182155] scsi 0:0:0:0: Direct-Access JMicron Generic 3102 PQ: 0 ANSI: 6 [ 6.193271] sd 0:0:0:0: [sda] Unit Not Ready [ 6.193290] sd 0:0:0:0: [sda] Sense Key : 0x4 [current] [ 6.193302] sd 0:0:0:0: [sda] ASC=0x44 <<vendor>>ASCQ=0x81 [ 6.194247] sd 0:0:…

• 1

  Reputation Points

• 23 replies
• 10.7k views
• 2 followers

rosbeef

May 2, 20215 yr

Hi! my odroid HC2 is running pretty great on armbian 5.90 for >1,5 years (24/7) now. Running a nextcloud instance, with decent perfomance, even when clocked to 600/1200 Mhz in the summer, because of one (1) crash, that I think might have been heat-related. The thing I'm wondering about: in htop, it shows only ( .LITTLE) cores for eight lines, but the cpu is a (.big.LITTLE) architecture and my other HC2 sbc, which runs armbian 20.02.7, show "(.big.LITTLE)" in htop. Perfomance in sysbench is equal on both boards, so this might mean nothing, but it still seemed strange to me. Anyone knows why htop only shows "( .LITTLE)" cores?

• 0

  Reputation Points

• 1 reply
• 3.4k views

piter75

October 17, 20205 yr

Hi .. I try to upgrade to latest armbian. I run now bionic Only when i do sudo apt-get-dist-upgrade i get no upgrade options. I was thinking i need to chage somewhere in setting something with tls. Only... So i cannot find a wiki or a other good working how to. So please can some help me to get my xu4 update tot latest version.. Or give me a good wiki or a working how to. Thanks!!

• 0

  Reputation Points

• 1 reply
• 3.1k views
• 1 follower

Werner

October 11, 20206 yr

Is there an armbian software distribution for the "Broadcom BCM2711" ? (rasberrypi 4)

• 0

  Reputation Points

• 6 replies
• 6.7k views
• 1 follower

Igor

May 21, 20224 yr

Hello I can not seem to get my USB Ethernet dongle with a r8152b chip to work on the latest armbian focal release. I tied both kernels 4.14.y. and 5.4.y with no luck. It works on "clean" ubuntu focal when i first plug it it without drivers and when i add the drivers. I am also posting in the odroid fourms here: https://forum.odroid.com/viewtopic.php?f=172&t=38713&p=306027#p306027 I am following these directions: tar -xf r8152.53.56-2.13.0.tar.bz2 cd r8152-2.13.0 make sudo make install lsmod | grep r8 If this works, and if the module does not load at reboot, add "r8152" in modules.conf: sudo vi /etc/modules-load.d/modules.conf…

• 0

  Reputation Points

• 6 replies
• 6.2k views

Igor

November 9, 20205 yr

Linux 2b8e 4.14.150-odroidxu4 #2 SMP PREEMPT Mon Oct 28 08:07:45 CET 2019 armv7l GNU/Linux DB 10.5 updates and upgraded High everybody AAMOE the starting procedure brings very often a new address for local use. As XU4 should be reachable by some other machines automatcally withour searching seconds an seconds I wonder if DHCP6 could help, when searching takes too much time and they already do have fixed IPv6 adresses and DHCP is disgusting. So, how the IPv6 ist made in Armbian? TIA

• 0

  Reputation Points

• 4 replies
• 4k views
• 1 follower

gleam

September 9, 20206 yr

Hi, guys. Little help here After being tired of my docker containers loosing connectivity to the internet I've decided to fully update/upgrade armbian (including the kernel) Now my system boots but most applications don't work. Most cases are missing kernel modules The /lib/modules dir contains the new updated content as the /boot too But the system keeps booting the old kernel image (4.14.176) and not the new one (4.14.195). It makes no difference if I upgrade the kernel via apt or via armbian-config I guess the issue is the files still in the SD card used for boot (they are 4.14.176 by it's names). Shouldn't armbian-config update those files? …

• 0

  Reputation Points

• 7 replies
• 6.2k views

Will Santana

September 1, 20215 yr

Hi armbian staff and users, i must/try to connect through uart (HC1 /Dev/ttySAC2) to an external uart device. 1. As uart /dev/ttySAC2 is used by boot/kernel, /sbin/agetty has been renamed to stop its launching / lock rather than rebuild uboot/... 2. So as powers supply of 2 uart are differents, 2 converters UART/USB are installed on 2 sides HC1 <-> UART/USB(CP2102N) <=======> USB/UART(XR21V14xy) <-> device. External PS 5v is connected on USB(vcc:gnd), red light on CP2102N is up. I precise 2 points : HC1 <-> UART/USB(CP2102N) <=======> laptop=OK DEVICE <-> UART/USB(XR21V14xy) <=======> laptop=OK Nothing TX/RX, where i…

• 0

  Reputation Points

• 4 replies
• 5.1k views

r2d2r01

September 3, 20206 yr

Hi all, I am trying to add SSH Keys to an HC1. The commands I am using are: sudo mkdir ~/.ssh sudo chmod 700 ~/.ssh sudo nano ~/.ssh/authorized_keys Then I select all the PUBLIC key from PuTTy Gen and copy/paste it on the file above, close and save the file. sudo chmod 600 ~/.ssh/authorized_keys sudo chown -R $(whoami):$(whoami) ~/.ssh/ sudo reboot I then try to SSH with PuTTy and SSH keys. Immediately I get an error saying "Server refused our key" and then it asks me for my normal password as a user. Any idea what I am doing wrong?

• 0

  Reputation Points

• 1 reply
• 4.7k views

Werner

July 20, 20206 yr

Hi! my nextcloud instance on an odroid hc2 running armbian has been running stable and smoothly for several months now. Thanks Igor and the whole armbian team! I have one question though: Task: I convert videos with ffmpeg to reduce file size and optimize them for streaming observed behaviour: the CPU is getting very hot! In the evening up to 100 °C (see below), but at noon I have seen temperatures of up to 115 °C! I read somewhere that 110 °C is the critical temperature for the board and the stock hardkernel image has an emergency shutdown implemented. But my board running armbian seems to be negligent of this. On a side no…

• 0

  Reputation Points

• 1 reply
• 4.5k views
• 1 follower

jshc1

August 28, 20206 yr

I do not use my HC2 for a while. Now I have issue to boot it up. I have download image ubuntu 18.04.3 from official odroid wiki link and during first boot blue led is blinking in heart beat rate forever, I was trying 18.04.1 and first boot run smooth, leds turn off and only red is on, but after reset I can not see my odroid in my network (I used two different cables to check if any is broken). Earlier when I was using it there was no problems.

• 0

  Reputation Points

• 0 replies
• 3.3k views
• 1 follower

Wojciech Rzepecki

July 10, 20206 yr

My board is Odroid HC1 Using balenaEtcher under Windows 10 I have instaled today Armbian_20.05.7_Odroidxu4_buster_current_5.4.50_minimal.img.xz and also was trying before Armbian_20.05.7_Odroidxu4_buster_legacy_4.14.187.img.xz. On both images I wanted to increase verbosity to 7 to see in serial console boot process. Changes in boot.ini are not used during boot until symlink /boot.ini is created which point to /boot/boot.ini Until this is done you will se uboot error that script /boot.ini is not found. Please add this symlink to images for XU4/HC1. Second issue is that editing armbianEnv.txt is not overwriting values in boot.ini. I ha…

• 0

  Reputation Points

• 3 replies
• 5.2k views

Igor

September 3, 20206 yr

https://dl.armbian.com/odroidxu4/archive/Armbian_20.05.2_Odroidxu4_bullseye_current_5.4.41.img.xz Third link on XU4 and HC1,2 MC1 download pages are 404 not found. Building an archive for a workshop I'm doing next week and got the 404. No big deal, just wanted to make a note.

• 0

  Reputation Points

• 0 replies
• 2.6k views
• 1 follower

Technicavolous

July 4, 20206 yr

First I have to thank all maintainers for their work. I ran this server for 1.5 years before something broke. Since armbian is maintained by volunteers I want to cheer you up and thank you for your hard work. However just today my little server would die after apt-update/upgrade. I use a SATA drive together with a boot SD-card (only containing /boot). I can observe the following behavior: The system leds indicate that booting is sucessful (blue LED does blink regularly, I can detect HDD usage by observing the green LED), yet SSH login that I have been using for years now is impossible. The device is also not responsive when pinging it. From my rout…

• 0

  Reputation Points

• 4 replies
• 4.9k views
• 1 follower

rosbeef

September 21, 20206 yr

Hello I have Odroid xu4 with fan mounted on heatsink. I found several tutorials online and I have one problem. I have Armbian buster with Linux 5.4.28-odroidxu4 I tried edit temp curve and I did it with nano /etc/rc.local # Target temperature: 30°C, 50°C, 70°C TRIP_POINT_0=30000 TRIP_POINT_1=50000 TRIP_POINT_2=70000 echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone0/trip_point_0_temp echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone1/trip_point_0_temp echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone2/trip_point_0_temp echo $TRIP_POINT_0 > /sys/devices/virtual/ther…

• 0

  Reputation Points

• 6 replies
• 8.7k views
• 1 follower

tbylit

June 2, 20206 yr

Hello everyone, odroid xu4 user here with buster minimal 5.4 from https://dl.armbian.com/odroidxu4/Buster_current_minimal please have a look at the following output ... May 19 12:58:11 localhost kernel: [ 1581.893003] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250) May 19 12:58:12 localhost kernel: [ 1582.352546] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) May 19 12:58:12 localhost kernel: [ 1582.389396] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84) May 19 12:58:12 localhost kernel: [ 1582.426230] mmc_hos…

• 0

  Reputation Points

• 3 replies
• 6.3k views
• 1 follower

chriss

May 21, 20206 yr

I'm having a hard time clarifying if OMV 5 is stable on Helios 4 and if there are any successful builds out there. Since there doesn't seem to be an upgrade path from OMV4 -> OMV5 and so requiring a full rebuild, I want to understand as much as possible before actually trying this new version out. Any successes out there?

• 1

  Reputation Points

• 9 replies
• 8.1k views
• 1 follower

Patrick Schlüter

July 5, 20206 yr

Hi all, I wanted to do some cross arch builds on my newly installed Armbian on an Odroid-HC1 buuut, it seems binfmt_misc support is not enabled in the kernel. Can I enable it somehow without recompiling the kernel? Thank you for this great image, kernel 5.4, omg!

• 0

  Reputation Points

• 1 reply
• 3.1k views

Igor

May 11, 20206 yr