Rockchip

Hi, Is anyone can able to help me with this ? NANOPIM4V2 + OMV and 4xSATA HAT does not boot-up after updating armbian-firmware/buster,buster 22.05.1 Is there any additional info I can get from my system and put here that will help ? Is this the right place to post this ? Thanks ----------------------------------------------------------------------------------- Welcome to Armbian 22.05.1 Buster with Linux 4.4.213-rk3399 System load: 5% Up time: 6 min Memory usage: 6% of 3.72G IP: 192.168.8.60 CPU temp: 37°C Usage of /: 16% of 29G s…

Title says it all: The Images offers by the site https://www.armbian.com/nanopineo3/ simply doesn't work on a NanoPi Neo3. I don't have a Serial-Connector to find out what's going on during the Boot-Process. I connected a Router on the Lan-Interface, and the Router never get a DHCP-Request from the Neo3. Tried multiple times, SD-Card is fine (tested). If I use an Image from a totally different Project (for Example "DietPi" which also offers a Neo3-Image), it works like a charm. Router gets DHCP-Request, I can connect using SSH (and so on), everything works. My Neo3 is working fine, Power-Supply is also good (it's made for Raspberry Pi and offers 5.1V and 3A...…

Hi, I got write errors on the eMMC, and the filesystem becomes read-only. Dmesg shows that: [ 304.982737] mmc2: running CQE recovery [ 304.987677] mmc2: running CQE recovery [ 304.989762] blk_update_request: I/O error, dev mmcblk2, sector 26826008 op 0x1:(WRITE) flags 0x4000 phys_seg 127 prio class 0 [ 304.989791] EXT4-fs warning (device mmcblk2p1): ext4_end_bio:345: I/O error 10 writing to inode 789645 starting block 3353569) [ 305.021383] mmc2: running CQE recovery [ 305.026213] mmc2: running CQE recovery [ 305.030808] mmc2: running CQE recovery [ 305.032702] blk_update_request: I/O error, dev mmcblk2, sector 26265544 op 0x1:(WRITE) fl…

Built latest image for a Rock 3c based device and am having an issue with ethernet connectivity. Boots fine. Wifi works well and it seems functional other than Eth connectivity. My old DTB (from 4.19) will not boot , using a rock3c DTB instead to get a 90% functional device Showing the following for ethernet dmesg | grep eth [ 0.000000] psci: probing for conduit method from DT. [ 3.199039] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 3.199576] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 3.199601] rk_gmac-dwmac fe010000.ethernet: TX delay(0x30). [ 3.199614] rk_gmac-dwmac fe010000.ethernet: RX delay(0x10). [ …

I'm in the process of upgrading my network and with the Helios64 capable of 2.5 GbE, what are some people's switch recommendations? My needs aren't really too high so I think 5 ports should be enough until the rest of the infrastructure catches up in my home network. My short-list are: * QNAP QSW-1105-5T * TP Link TL-SG105-M2 * TRENDnet TEG-S350 Article from servethehome

I have a problem i cant install armbian to orange pi 5b - i change armbianEnv.txt file (change to 5b) and when i use sudo armbian-install and choose 2nd option install mmc installer hangs and saying everything is allright but i cant boot after install without sd card. I have video of this: https://youtu.be/GKfPTD2PKRM Please help

Anybody have success with panfrost? kernel module and userspace module I have firefly 3399( 5.4.8-rockchip64) board And I don't see panfrost in dmesg or lsmod Any idea?

Tried installing rock 4se image and rockpi 4b image. Both blink the blue led but none gives me hdmi output or network connection. What is the correct image for this sbc? The silkscreen says rockpi 4 SE Thanks

Hello all, After some time without touching it, I came back to my Rockpi 4B. I installed the latest armbian bionic image on a samsung 64Go card. All seems to work fine for the first boot. But when I try to restart the system I don't get any display on screen. To get it back I need to unplug HDMI plug and re-plug it. Didn't found any conversation about that trouble? Is it a bug or is there something I can do to fix it ? Thanks for your answers. Pat

I have an Orange Pi 4B. The board as the only USB 3.0 port has the USB-C type. I connect the USB-C x USB-A adapter. I connect the USB flash drive and it doesn't work. Power from the port is coming out properly. Is there any chance that this port will work properly with an external drive?

Hi everyone, I have been playing a lot (too much maybe) with my NanoPi M4. It seems that most of what I need will be working "soon" (yay for hardware decoding), except HDMI audio bitstream passthrough. Whatever kernel I try, I always get this output from Kodi: Device 1 m_deviceName : default m_displayName : Default (hdmi-sound ff8a0000.i2s-i2s-hifi i2s-hifi-0) () m_displayNameExtra: m_deviceType : AE_DEVTYPE_PCM m_channels : FL, FR, LFE, UNKNOWN1, FC, BC, BL, BR, BLOC, BROC, FLOC, FROC m_sampleRates : 32000,44100,48000,88200,96000,176400,192000 m_d…

Armbian version 22.05.3 Focal Nanopi M4V2 There seem to be only default modes available with the nanopiM4V2. Manual adding a resolution does not work (it is added, but has no effect when selected) NanoPIM4V2 Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 4096 x 4096 HDMI-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axi> 1920x1080 60.00* 60.00 50.00 1920x1080i 60.00 50.00 1280x1024 60.02 1280x960 60.00 1280x720 60.00 50.00 1024x768 60.00 800x600 60.32 56.25 720x576 50.00 720x480 59.94 The monitor is a …

Getting system crashes and instability, including a loss of HD I/O, during very large file transfers. This happens over the network, whether using SCP, FTP, or SMB. I'm a hobbyist, and am no coder or developer, so other than Googling, I have no practical knowledge to pull on. When the problem started occuring, I opened two PuTTY SSH interfaces as root - one with htop, and another with "dmesg --follow" to see what was going on with the system, and this is what happened: dmesg readout at file transfer crash (using SMB this time): Spoiler [238803.445307] ------------[ cut here ]------------ [238803.445321] kernel BUG at mm/vmscan.c:1709…

After installing the hardware and software, my hdd 1 is inactive. I swapped my disk 1 and 5, 1 is still inactive. I checked my connections in the box but I don't see any problems. Could this be due to a software error?

Dear maintainers, Guess some device tree issues with neo3 got me into this mess, since rk3328-nanopi-neo3-rev02.dtb is missnig. Scanning mmc 1:1... Found U-Boot script /boot/boot.scr 3185 bytes read in 7 ms (444.3 KiB/s) ## Executing script at 00500000 Boot script loaded from mmc 1 428 bytes read in 6 ms (69.3 KiB/s) 12514638 bytes read in 556 ms (21.5 MiB/s) 30083584 bytes read in 1326 ms…

With the recent update of the kernel "edge" package (6.8.11-edge-rockchip64) when the system boots. interfaces get different names (they used to be "end0" and "eth1" before, and now they are "eth0" and "eth1"), but more importantly, they both show different MAC address (the old address returns when previous kernel is booted). It took some time to figure why it did not appear on its prescribed address... Anyone notice this, or has a clue why? Armbian 24.5.5 noble Linux kobol 6.8.11-edge-rockchip64 #1 SMP PREEMPT Sat May 25 14:28:41 UTC 2024 aarch64 aarch64 aarch64 GNU/Linux

Have tested the Orange Pi 5 Ultra and the Armbian Linux v6.1 vendor IOT image for the 5 "Max" model, using the same Max' `rk3588-orangepi-5-max.dtb` FDT file works better than with the rk3588-orangepi-5-ultra.dtb (extracted from the old official Orange Pi image), as surprisingly, dmesg shows less errors with the Max DTB. Tested: ✅ eMMC works. HDMI ports: ✅ Port 1 out works fine. ❓ Haven't tested the port 2 input. Would guess it doesn't work as the Max has bot ports as output. For the AP6611s (SYN43711): ✅ WiFi: works. ✅ Bluetooth: works with some extras, rfkill and bluez: …

Hello, Has any one installed and used OV5647 Sensor camera on orange pi 3b ? I can see the camera is listed. but there is no driver. Below is output. Can some one help ? -la /dev/video* -rw-rw---- 1 root video 67 Aug 8 13:53 /dev/video-dec0 -rw-rw---- 1 root video 4 Aug 8 13:53 /dev/video-enc0 sudo modprobe sun6i-csi [sudo] password for XXXXX: modprobe: FATAL: Module sun6i-csi not found in directory /lib/modules/6.1.115-vendor-rk35xx dmesg | grep -i mipi [ 12.108168] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: enter mipi csi2 hw probe! [ 12.108575] rockchip-mipi-csi2-hw fdfb0000.mipi-csi2-hw: probe success…

My Helios64 is "far away" and I am afraid to change network configuration, because if I miss something I could lose connectivity to the box. I would like to attach COM-to-IP adapter so that I always had serial console available, but... what actually do I need? "Normal" com-to-ip adapter provides COM port. Helios64 has COM-in-USB. So...? How to convert Helios'es serial console to anything accessible via LAN?

Hi there, So I'm having a problem connecting the helios to the router. I try different lan cables and different ports. It was working everything fine yesterday, I did a reboot and no more connection. I'm completely new to this. I was installing home assistance and plex before this happened but I believe I didn't mess with anything to do with network. Don't know what I might have done. I can connect to helios via putty and after logging in the part where ip should be there is none. Any advise would be most appreciated. Again I'm completely new to this.

I have a Ambian 6.12.7-Edge-Rockchip64 minimum installation. How can I enable or upgrade to a desktop environment without changing the kernel? Thank you

Hi guys, sorry if this question might sound stupid, but how do I open the M3 enclosure? There is no instruction in the manual, nor on the stationpc website. I just bought this little box and I am not sure if this has some screws or some other closing system. I can see the four rubber buffers on the bottom of the box, but I don't want to harm those without reason. Can anyone tell me how to disassemble the box? Thanks in advance.

Hello, Sorry for my bad english, I'm French, I'm using "Armbian_20.11.4_Helios64_buster_current_5.9.14.img.xz" During the startup sequence I get the following errors: GPT 0x3380ec0 signature is wrong recovery gpt... GPT 0x3380ec0 signature is wrong recovery gpt fail! LoadTrust Addr:0x4000 No find bl30.bin No find bl32.bin Load uboot, ReadLba = 2000 Load OK, addr=0x200000, size=0xdd6b0 RunBL31 0x40000 NOTICE: BL31: v1.3(debug):42583b6 NOTICE: BL31: Built : 07:55:13, Oct 15 2019 NOTICE: BL31: Rockchip release version: v1.1 INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 …

I got my box yesterday and assembled it (looks gorgeous, and reasonably easy to assemble). Without external power and with battery connected, green led 1 is on. With external power, orange led 9 in addition to that. FTDI chip is recognized regardless of power status, I can connect to the console. After pressing power button, green LEDs 2 and 3 and blue LEDs 4 and 5 light up immediately, and after that nothing else happens. Nothing on the serial console, no LEDs change status. Tried disconnecting the battery. Then without external power, all LEDs are dark (but FTDI chip is still visible), with external power orange LED 9 blinks, the rest is exactly the …

Hi guys, I have checked the Buster image and stuck in following issue: On Rockpis, tty2 and (the only working) spi2 sharing the same PINs. Due to this reason, SPI is not functional . from dmesg: [ 1.598230] rockchip-pinctrl pinctrl: pin gpio1-22 already requested by ff0c0000.serial; cannot claim for ff140000.spi [ 1.598269] rockchip-pinctrl pinctrl: pin-54 (ff140000.spi) status -22 [ 1.598287] rockchip-pinctrl pinctrl: could not request pin 54 (gpio1-22) from group spi2-miso on device rockchip-pinctrl [ 1.598304] rockchip-spi ff140000.spi: Error applying setting, reverse things back I try to switch back tty2 to tty0 in dts and also…

Hello everyone, I've been running my Helios64 for about 2 months now. My system is installed on the eMMC and i'm running a few docker containers (all from linuxserver.io) Radarr Sonarr Bazarr Transmission Jackett Jellyfin I'm having difficulties with Jellyfin and my media library. When lauching tv shows or movies, the CPU rockets to ~97-99% use and the media is constantly stopping to load. I would like to know what I can do to ease the strain on the CPU and be finally able to use Jellyfin. Has anyone been able to use hardware acceleration with docker ? What info can I give you to shade li…

Gentlemen, I have a rock64 board, and I would like to use an external RTC module with DS1307 chip. Unfortunately the armbian kernel does not provide DS1307 driver by default: root@rock64:~# cat /boot/config-4.4.162-rockchip64 | grep DS1307 # CONFIG_RTC_DRV_DS1307 is not set I don't have the programming skills for sending a pull request to enable this module. Could you please enable this module for ROCK64? I believe other ROCK64 owners may also benefit from this driver, as the board does not expose a working RTC, and DS1307 is a very common RTC chip. Thanks in advance.

Hello, can someone help me with my problem. I have a ROCK64 with 4GB of RAM and an ARMBIAN 5.75 stable Ubuntu 18.04.2 LTS 4.4.174-rockchip64, installed. My issue come with usb ports, from the three USB of the this device only works two: one 2.0 and 3.0. And when i have a disk connected towards usb 3.0 i have issues with port usb 2.0, it doesn't work well and I end up disconnecting the USB 3.0 to can work with my device connected towards USB 2.0 so I assume that the current power on the USB port is having issues or it's not working well. Anybody an idea? thanks!

Hi guys. I've been working with the 4.19 kernel before on M2. I upgraded to the kernel version 5.18 today. I found that I can't find the registered udc device anymore. This is auto-registered on the 4.19 kernel and you can find it under /sys/class/udc. root@station-m2:/boot# ls /sys/class/udc fcc00000.dwc3 I would like to ask how to enable the udc device on the 5.18 kernel. Thank you.

Your build Armbian 5.65 kernel 4.4 and my build 5.65 the same kernel - system has sound only via HDMI monitor. Is it possible to enabled audio via 3.5 jack or external USB sound card?

Hi all, I am unable to login to OMV on my Helios64. A bit of sleuthing indicates that this is because the / fs is at 100% capacity. At first, I figured I'll just transfer the system install from the 8GB SD Card I started with to the 16GB internal eMMC. Turns out past unfnknblvbl already did that, and now I need to go the other way. The documentation on the old Kobol site isn't entirely accurate about how to do this. My SDCard is /dev/mmcblk1 and even though it's formatted ext4, it simply doesn't show in armbian-config. In fact, the only device that shows in the Install menu is /dev/md127, which is the RAID array itself. I'd rather not be booting f…

My NAS do very little overnight so my NAS4 shuts down in the evening and shortly afterwards a physical time switch cuts the power - reinstating power in the morning at which time the NAS4 automatically reboots. I want to do the same with the NAS64 - but even though I've read this (https://wiki.kobol.io/helios64/auto_poweron/) I'm not sure how to go about it. I can't understand if it only works if the UPS has died, or if I have to run a script before shutdown or both. Could you please clarify? Thx ... Nick

Hi Gents, I would like to ask for your help or tips and tricks in the following problem... Basically to keep the long story short, I have a custom board with RK3566 and 2 GB of RAM, 32 GB Samsung emmc on it ... basically if you are familliar it is a Linxdot Helium miner which has some problems with the onboard Lora module. I had tried to flash using RKDevTool a few Debian version that I found for Rk3566 but not all of them worked properly. All the time I was able to reflash it by using RKDevTool by pressing the button while I powered up the board but after flashing the Armbian minnimal for Orange Pi3B I can't use the RKDevTool anymore, it is simply n…

Hi all i tried to compile BTT CB2 with bookworm and vendor kernel to get MPP and NPU working, but got that : sha256sum: config/kernel/linux-rockchip64-vendor.config: No such file or directory is it missed ? How to compile vendor kernel for MPP support? thanks

Current build hangs whilst booting , any ideas anyone ? DDR Version 1.25 20210517 In soft reset SRX channel 0 CS = 0 MR0=0x18 MR4=0x1 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 1 CS = 0 MR0=0x18 MR4=0x1 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x0 MR19=0x0 MR24=0x8 MR25=0x0 channel 0 training pass! channel 1 training pass! change freq to 416MHz 0,1 Channel 0: LPDDR4,416MHz Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB Channel 1: LPDDR4,416MHz Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB 256B stride channel 0 CS = 0 MR0=0x18 MR4=0x1 MR5=0x1 MR8=0x10 MR12=0x72 MR14=0x72 MR18=0x0 MR…

When is it likely to get support and Armbian image for Orangi Pi 4B? Thanks Rajesh

Fresh build edge bullseye image with kernel Linux helios 5.18.0-rockchip64 #trunk SMP PREEMPT Sun May 29 20:19:27 EEST 2022 aarch64 GNU/Linux fancontrol not work, because there no /dev/fan devices How to get fancontrol back to work?

I used both buster and ubuntu images (Armbian_5.91_Nanopineo4_Debian_buster_default_4.4.179_desktop.img and Armbian_5.90_Nanopineo4_Ubuntu_bionic_default_4.4.179_desktop.img), both have no wifi, only show "device not ready". So I extracted firmware from official friendly desktop image and unzip to /lib/firmware/rkwifi/ and wifi works. I'm a newbie and hope this could be fixed properly soon. For those new to linux like me, download the attachment, extract everything to /lib/firmware/rkwifi/, reboot and wifi should be there. ap6212.zip

HI. I burned the latest official Rockpi4 focal kernel 5.8.x on both rockpi 4 B and C. The problem is only present on the C model. Both USB 2.0 aren't working at all.

I don't know where else to share this so I'm putting this here. The board recognizes and tries to the load the driver for an AR9462 QCNA222 M.2 WiFi card, but fails. I tried a custom build found on Radxa forum/github, built Armbian myself, and tried an official build. All resulted in the same error. Card was tested and working correctly on 2 different Debian x86 machines. lspci 0000:00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01) 0000:01:00.0 Network controller: Qualcomm Atheros AR9462 Wireless Network Adapter (rev 01) 0002:20:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01) dmesg ath…

Hello I recently set up NextCloudPlus/NextCloudPi on a Rock64. I used the image that can be downloaded from the ownyourbits website, cat /etc/*-release resulted in the following output: BOARD=rock64 BOARD_NAME="ROCK64" BOARDFAMILY=rk3328 VERSION=5.44 LINUXFAMILY=rk3328 BRANCH=default ARCH=arm64 IMAGE_TYPE=user-built BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image 03af3b07-6131-4b1c-8cc2-7f716caf75e1 # PLEASE DO NOT EDIT THIS FILE BOARD=rock64 BOARD_NAME="ROCK64" BOARDFAMILY=rk3328 VERSION=5.44 LINUXFAMILY=rk3328 BRANCH=default ARCH=arm64 IMAGE_TYPE=user-built BOARD_TYPE=conf INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image PRETTY_NAME="Debian GNU/Linux 9 (stretch…

I'm getting this weird graphical artifact on a Radxa Rock 4SE connected to a TV via HDMI. It covers roughly a third of the right side of the display, note that the terminal window is covered by the artifact but the cursor is above it. I started from a Debian minimal image and added the desktop environment via armbian-config. The artifact is visible on both GNOME and KDE Plasma (with fully updated system on both rolling and stable) but not with XFCE. It also disappears with resolutions lower than 4K or switching to tty. Any idea what might be causing this?

Hi All, in an attempt speed up my Armbian image build process I put the last build choices in a bash script ./compile.sh BOARD=nanopim4v2 BRANCH=current BUILD_DESKTOP=yes BUILD_MINIMAL=no\ DESKTOP_APPGROUPS_SELECTED='browsers editors'\ DESKTOP_ENVIRONMENT=gnome\ DESKTOP_ENVIRONMENT_CONFIG_NAME=config_base\ KERNEL_CONFIGURE=no RELEASE=jammy but I still get prompted for input when I run the script - what am I doing wrong ?

Hi! I have the problem that when I try to boot with any Kernel other than 4.4.x, U-boot gives me the "Bad ARM64 Image Magic" Error and stops booting. I can build my own 4.4 Kernels without any problem, those will boot fine. But If I try any newer kernel, for example a NEXT Kernel (package linux-image-next-rockchip), or a DEV Kernel (package linux-image-dev-rockchip), or even if I compile my own 5.3 Kernel, a boot attempt always results in the Bad Magic error. I also have this problem when I install a whole 5.3 Armbian Image (for example https://dl.armbian.com/rockpro64/Buster_current_desktop) I have three RK3399-…

Setup: Helios64 with Armbian 20.08.8 Buster with Linux 4.4.213-rk3399. Will change to Linux 5.8 soon though. 5 x 8 TB drives. Not using battery. I’ve had this issue ever since beginning to use my Helios. It first happened when I tried building a RAID with OpenMediaVault: It would crash and reboot while building. Sometimes after only 10 minutes, sometimes after 8+ hours of working. The same is true for video transcoding nowadays: it will sometimes crash after a little while, sometimes after a few consecutive hours of working, but it will never be able to work much longer than 12 hours on such a task. Copying large files from the internet has a similar risk of c…

I originally installed Armbian witk Kernel 4.4 on my Nanopi.m4 and later upgraded it to 5.10 via armbian-config. Things work fine but whenever I got a new update via apt update, things get messed up a bit the /boot/Image got linked to vmlinux-4.4.213-rk3399 instead of vmlinuz-5.10.35-rockchip64 while others uInitrd -> uInitrd-5.10.35-rockchip64 dtb -> dtb-5.10.35-rockchip64 The result's the board couldn't boot-up, when I restarted it. And, I need to correct the Image -> vmlinuz-5.10.35-rockchip64 and doing mkimage -C none -A arm -T script -d boot.cmd boot.scr from another linux machine to the SDCard. It works fine …

🏆 Become a sponsor, help to add other boards in armbian standart, you don't need to be a programmer to help the community, just need a copy of the ARM BOARD and a x86 computer to compile new versions. If you like what you see here and want to help: Donate Armbian the like button only costs a few dollars. Here, I will document the efforts to get the Easy EAI RV1126 board into Armbian. Uboot: Link boot: Link MiniLoaderAll.bin: Link Docs available on: Link Build Command: ./compile.sh BOARD=easy-eai-nano BRANCH=vendor BUILD_DESKTOP=no BUILD_MINIMAL=yes KERNEL_CONFIGURE=no RELEASE=resolute ./compile.sh BOARD=ea…

Hello, I have an ARMBIAN image 08.21.6 kernel 5.10.16 it works very well on rockpi 4B + rev 1.6 I tested the last Kernel but without more success. when we fix the ip address and we up (several times) the eth0 network this one puts to work at a time. Do you have an idea ? Regards.

I have installed Armbian 21.02 Ubuntu 20.04 Focal with Linux kernel 5.10.16 and OpenZFS 2.0.1-1 on my Helios64. Created a three-disk encrypted RAIDZ pool with the following command: sudo zpool create -f -o ashift=12 -O compression=lz4 -O atime=off -O acltype=posixacl -O xattr=sa -O encryption=aes-256-gcm -O keylocation=prompt -O keyformat=passphrase tank raidz1 /dev/disk/by-id/foobar1 /dev/disk/by-id/foobar2 /dev/disk/by-id/foobar3 Then I did a single sequential read benchmark with fio on /tank: cd /tank sudo fio --name=single-sequential-read --ioengine=posixaio --rw=read --bs=1m --size=16g --numjobs=1 --iodepth=1 --runtime=60 --time_based …

Getting free() invalid pointer issue when installing / using python3. Could be dpkg issue as well ! When I did sudo apt update && sudo apt upgrade, it happened and hence I tried to reinstall. This issue occurs when trying to manage it with ansible as well. I think something might be wrong with the latest python. Board: Helios64 (I know, I know CSC) Chipset: RK3399 Apt install logs: Reading package lists... Done Building dependency tree... Done Reading state information... Done 0 upgraded, 0 newly installed, 2 reinstalled, 0 to remove and 0 not upgraded. Need to get 0 B/472 kB of archives. After this operation, 0 B of additional …

hello. I have found that you made firmware for MiQi board ( Rockchip RK3288 ). Is this firmware compatibile with Tinker Board ASUS ? It has the same SOC.

Hello, i'm experiencing random reboots on my RockPi 4b. I firstly recognoized this when my Squid Proxy Server was not working anymore because it had no permissions to its var/log/squid directory. What i saw (lsblk) that /var/log/ is only of a size of 50mb. Will that be the cause for the reboots? Does the system crash when the logs are full? My System is a Rock Pi 4b with 32gb emmc storage. Debian Stretch with Armbian Linux 4.4.192-rockchip64 Armbian Release 5.90 (i dont know how to change to the next version as armbian-config does not provide the switch to next button) Output or Armbianmonitor -u http://ix.io/22oZ

Hi everyone, Two Questions: 1) I have two Orange Pi 3 LTS boards at home. I installed AdGuard Home on one, serving as DHCP (I'll call it OP1), and on the other, I left a Docker with other apps (qbittorrent, omv6, samba, etc. - I'll call it OP2). Both are installed via SD card. But if there's a power outage, OP1 works normally again after, without any problems. But OP2, on the other hand, has experienced data corruption several times. Does anyone know why OP1 works fine and OP2 runs the risk of having to reinstall the system in such a case? 2) If I used a board with EMMC memory and unified all the system…

I have just put my Helios64 into operation. I have 5 HDD with 10TB each. Three HDD I mounted with ZFS (0.86) to a raidz1. the other two disks I mounted individually, formatting one disk with XFS and the last disk already had NTFS as filesystem. On this disk (NTFS) I have some very large *.vhdx files which I only use for copy tests. I use the console with the Mitnight Commander for this. The copying from the NTFS disk to the XFS disk reached a speed of about 130 MB/s. Copying from the XFS disk to the ZFS raid reached a speed of about 100 - 110 MB/s. I cannot do anything with these values alone. Can someone please tell me if these speeds fi…

Hi, I installed recent server armbian on orangepi pc 4 and trying to make the microphone work The command I use arecord -D hw:0,0 -f cd -d 5 test.wav The setup root@orangepi4-lts:~# uname -a Linux orangepi4-lts 6.6.62-current-rockchip64 #2 SMP PREEMPT Sun Nov 17 14:08:59 UTC 2024 aarch64 aarch64 aarch64 GNU/Linux root@orangepi4-lts:~# cat /etc/issue Armbian 24.11.1 Noble \l root@orangepi4-lts:~# arecord -l **** List of CAPTURE Hardware Devices **** card 0: rockchipes8316c [rockchip-es8316c], device 0: ff880000.i2s-ES8316 HiFi ES8316 HiFi-0 [ff880000.i2s-ES8316 HiFi ES8316 HiFi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: hdmisou…

Hi all, I would like to ask support for the board EMB-3531. I'm having problem with booting this board from SD card. Here are some informations about this board. I hope that someone can help me with it. Thank you so much! I try to erase the emmc and flash the MiniLoaderAll.bin but it doesn't help. Or i don't have a correct image with armbian for this board. https://my.kos.org.cn:5154/rockchip/EMB3531/emb3531.pdf

Hi to all, after the 16GB of the eMMC is slowly reaching my limits, I installed a 128GB M.2 SSD and wanted to use the kobol tutorial to transfer the system data on it... https://wiki.kobol.io/helios64/install/transfer/#transfer-rootfs-from-emmc-to-sata-or-usb ... unfortunately I see at position 4 only /dev/md0 instead of the M.2 Sata on /dev/sda root@helios64:/dev# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 119.2G 0 disk sdb 8:16 0 3.7T 0 disk └─md0 9:0 0 7.3T 0 raid5 /srv/dev-disk-by-label-nas sdc 8:32 0 3.7T 0 disk └─md0 9:0 0 7.3T 0 raid5…

I think i messed up with armbian-config, namely with 'system' sub section. I noticed that lately the only images that boot are armbian with kernel 6.9.x Nothing, i say nothing with a lower kernel number would boot -- even those SD cards that were good last time i tried them. None of orangepi factory images boot. In and out of itself, it is not a problem. Yet. But what if something changes in a future?

BOARD - Orange Pi 5 Pro PROBLEM Device Tree overlays defined in armbianEnv.txt are not being applied during boot. The overlay file exists but is not loaded by the system. verbosity=1 bootlogo=false console=both extraargs=cma=256M fdtfile=rockchip/rk3588s-orangepi-5-pro.dtb rootdev=UUID=a8beb1c4-8079-4e64-8216-8e893f7809d4 rootfstype=ext4 overlays=orangepi-5-pro-disable-leds usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u I also tried with overlay_prefix=rockchip overlays=orangepi-5-pro-disable-leds The Kernel is Linux orangepi5pro 6.1.115-vendor-rk35xx #1 SMP Mon Feb 23 05:39:00 UTC 2026 aarch64…

Hi, I was testing images for Orange Pi 4 w/o eMMC, official from site, Debian and Ubuntu from ARMbian, and suddenly any boots anymore. I tried desperately everything, write with another program, used dd for copy, pressed randomly bottoms attached in the back, then one time worked, but it crashed when i attached a keyboard. Later all my micro-sd cards worked, most of them are poor quality, could be that but idk, my power adapter came from official website. # ls usb doesn't show hid I have a cp2012 usb to tll, i can use it for serial debug ?

I have the following hat http://wiki.seeedstudio.com/Raspberry_Pi_Relay_Board_v1.0 my image detects the i2c interfaces and mounts them in /dev as i2c-0 i2c-1 i2c-3 i2c-4, I can scan the different i2c interfaces as folloging interface i2cdetect -y 1 root@rockpi:~# i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: UU 11 -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 6…

Hello Guys, i'm positiv with Corona and in quaratine in my sleeping room while the rest of the family stays in the other rooms. So i can't backup my system with the MicroSD-Card... Can i install the latest updates? 20.11.4? And the other stuff showing? armbian-config/buster,buster 20.11.4 all [aktualisierbar von: 20.11.3] linux-buster-root-current-helios64/buster 20.11.4 arm64 [aktualisierbar von: 20.11.3] linux-dtb-current-rockchip64/buster 20.11.4 arm64 [aktualisierbar von: 20.11.3] linux-image-current-rockchip64/buster 20.11.4 arm64 [aktualisierbar von: 20.11.3] linux-u-boot-helios64-current/buster 20.11.4 arm64 [aktualisierbar von: 2…

Armbian/Jammy is working like a charm, thanks guys. Settings up the encryption was a bit of bitch but its working as you can see. Any chance of adding encryption to the installer?

How to install mali gpu driver for orangpi 5b with debian bookworm image ?

I've been having HDD/SATA issues with my zfs pool, as have many others. Now my HDDs will not spin up or be recognized when on slot 1 or 2. What's wrong, how to check and what to check? Any help appreciated.

Hi folks, I have a Firefly AIO-3399C which boots Armbian fine, but no USB devices besides the root devices are detected. This happens with both the kernel 5.19.170 and 6.0.7 based images, made by @balbes150, which I've downloaded from https://users.armbian.com/balbes150/firefly-rk3399/ Any advice would be appreciated. U-Boot 2022.04-armbian (Nov 03 2022 - 17:26:20 +0300) Linux firefly-rk3399 5.19.17-media #trunk SMP PREEMPT Thu Nov 3 17:40:36 MSK 2022 aarch64 aarch64 aarch64 GNU/Linux In dmesg output, I see the following, which may be relevant: [ 4.616394] hub 7-0:1.0: USB hub found [ 14.296598] fusb30x: module is from the sta…

I am thinking to buy NanoPi M4v2 and i want to use with nvme SSD. RockPi 4 support Gen 2.0. What about NanoPi? NanoPi only support Gen1? And what is the maximum theoretical speed for nvme SSD on NanoPi M4v2 ? I am between NanoPi M4v2 vs RockPi 4 and NanoPc T4. I like NanoPi M4 design and box, I don't like rock pi ssd hat and box, and NanoPc price is expensive, not compact like NanoPi, ram is LPDDR3 others LPDDR4, but x4 lane and support Gen 2.1 is good. I am so confused..

I have previously successfully been using the USB serial gadget as terminal on the Nanopi R2S. The last working release I have tried was: Linux 5.4.45-rockchip64 #20.05.3 SMP PREEMPT Wed Jun 10 11:47:27 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux Now I am running the following version (Also tried 20.08.08) and the gadget mode does not work after boot. Linux 5.8.14-rockchip64 #20.08.10 SMP PREEMPT Tue Oct 13 16:58:01 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux I have seen no warnings or error messages when running dmesg. After boot on the failing versions the log contains the following section, which I assume means that the driver …

Hello, I just need to check the NPU driver version on my Orange Pi 5 with Armbian_24.11.2_Orangepi5_noble_current_6.12.0-kisak My command is sudo cat /sys/kernel/debug/rknpu/version but error No such file or directory Is there NPU driver on this Armbian OS?

Hi, How can I catch the reset button pressed. In other words, how can I change the behavior of the reset button on RK3399?

My NanoPi M4V2 wont boot. It has a solid red light no green at all. I cant access it with SSH. I went through the troubleshooting checklist available for the NanoPi in regards to the red light. Nothing was solved. I tried different SD cards with different types of images and different types of burners. Nothing works. I know that the SD cards, images, and burners are not the problem cuz I tested it on a Raspberry Pi with no problems.

Hi all, I’m working with an RK3588-based board and running into a frequency scaling issue. All cores (cpu0–7) are stuck at 408 MHz, despite available OPPs going much higher (up to 2.35 GHz on the big cores). Attempts to raise frequencies via scaling_setspeed or userspace governor have no effect. The image I'm using is: https://www.armbian.com/nanopc-cm3588-nas/ (https://dl.armbian.com/cm3588-nas/Bookworm_vendor_minimal-omv) Device tree file is: fdtfile=rockchip/rk3588-friendlyelec-cm3588-nas.dtb # for cpu in /sys/devices/system/cpu/cpu[0-9]*; do echo "== $(basename $cpu) ==" cat $cpu/cpufreq/scaling_available_freque…

What gives with the Armbian website links? Links to all previous versions Armbian for the OrangePi R1 Plus LTS have been removed. The links to SHA hash and PGP signature do nothing. I was hoping to use an image that was based on Debian Bullseye, but that link has been recently removed. It is possible to create my image, but I would spend my time working on my code, not wading through the options to create an image.

I have serious issues with the serial number being exposed in /proc/cpuinfo. Especially when browsers have access to this information. Afaik, its u-boot who passed this information on to Linux. Any idea how to mask this from Linux? Your help is appreciated

Hi there, https://www.armbian.com/rockpi4/ I see there are specific builds for versions. Version A, the link does not contain an image. Does the general image work on all versions? or the link is simply broken? Kind regards

Hi, I wanted to convert my root filesystem to btrfs. This allows me to use snapper to take regular snapshops. I also use btrbk to send my snapshots to my secondary storage (also a btrfs array). My root filesystems is installed to eMMC, but there isn't any reason you couldn't do this with an sd card. These instructions are done with a laptop running Linux. I'm using Debian in this case, although any distro with a recent kernel and btrfs tools installed should work. CAVEATS: The current u-boot image (2020.08.21) doesn't support booting natively to btrfs. u-boot *does* support btrfs though. Hopefully a future build of u-boot will add btrfs…

I am currently on Armbian 22.05.0-trunk with bleeding edge Linux 6.1.11-rockchip64 according to the main boot page in terminal I was in the process of converting an elegoo neptune 4 into a non-neptune version of klipper followed a guide that used a script was on the last step which was to do a system update...and upon reboot, I have no ethernet devices all I see is loopback what do I do to get my hardware ethernet interfaces back? this device does not have a removable SD card, but it does have a serial port... so everything must be done thru command line armbian monoitor.txt

I have nfs server. Whenever I do "systemctl stop nfs-kernel-server" I can see this in dmesg: lockd: couldn't shutdown host module for net f00000a1! Later when I do "systemctl start nfs-kernel-server" I see this: NFSD: starting 90-second grace period (net f00000a1) Of course "systemctl restart" gives me both messages in a row. Any idea what does it mean? What the hell is this "f00000a1"? Except strange messages everything seems to work fine...

Hello everyone, I seem to have a problem with not knowing how to change the top usb3 port of my Rock pi 4+ to host mode from otg mode, I just got it and installed armbian on it and open media vault, only to notice that I couldn't connect anything to the top usb 3 port and have it show up in open media vault, the other ports work fine and looking at the internet seems to have found that the answer is that the port is in OTG mode and on the official website they do have a way to change it to host mode, but not in armbian and I'm not skilled enough in linux to find where the file I need to change is. I'm running this build "Armbian_v22.05.2_Rockpi-4cplus_bullseye…

Does armbian for orange pi 5b provide headless wifi setup like raspberry pi? on raspberry pi, I can modify the sd card. like `touch ssh` and assign wifi login and password in the .conf to achieve headless wifi setup. I don't have a lan cable, monitor and keyborad to set up.

Hi, I try use image http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=3844 this only one image works HDMI input for HDMI output PC ffmpeg -f v4l2 -list_formats all -i /dev/video0 [video4linux2,v4l2 @ 0xab89b120] Raw : yuyv422 : YUYV 4:2:2 : [video4linux2,v4l2 @ 0xab89b120] Raw : yuyv422 : YUYV 4:2:2 : [video4linux2,v4l2 @ 0xab89b120] Raw : uyvy422 : UYVY 4:2:2 : [video4linux2,v4l2 @ 0xab89b120] Raw : yuv422p : Planar YVU 4:2:2 : [video4linux2,v4l2 @ 0xab89b120] Raw : Unsupported : Y/CbCr 4:2:2 : [video4linux2,v4l2 @ 0xab89b120] Raw : yuv4…

Hello! On newer kernel (5.10.63+) gpio behaves strangely. Led connected to gpio pin blinking opposide status led. Also it break spi work. armbianmonitor logs https://paste.armbian.com/faqorefumi VID202304051140011.mp4

Looks like OPi4 has two active UART interfaces (ttyS2, S4). S2 is connected to the back 3 pins which are the debug ports, and S4 is uart on pins 19,21. Is there anyway to bring up another interface for UART on Pins 8, 10? Ive tried adding uart1,2,3 etc in armbianEnv file in /boot as well as console=display but non of this works.

Sorry to repeat another case of this. Have attempted a few times to move boot from SD card to eMMC before the SD card fails. I did according to the wiki doc with nand-sata-install. Since I have OMV, I excluded the exports, and also afterward copied the salt and pillar. Also, in another attempt, on suggestion from another thread, I updated the boot loader and copied again. I can boot to my SD card, mount the eMMC, and see the root structure. From what I can tell in reading the boot output, it can't find any storage device? 4 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found But I can see it whe…

Kia ora. I am aware that the external USB ports on the Helios are able to deliver up to 900mA per port. I am wondering whether it is possible to find a power source inside the Helios64 that would be able to deliver, say, 2.5A at 5v? Maybe somewhere quite soon after the 12v power in...? 🤔 Jon

Hello. I bought a Rock64 and I have a lot of errors. Im using a eMMC 32GB Storage with Armbian 5.65 stretch 4.4.162 Desktop, Ethernet connection with TP-Link switch, a Wireless Keyboard with touch pad and the original 5V 3A Power Supply. HDMI is connect to a HDMI Splitter/Switch. The Rock64 is placed in the Aluminum casing. Full-Log: http://ix.io/1rce The system is reboot very often before i see the Desktop. Sometimes only after several resets. Can someone help me?

I have an FriendlyElec M4v2 board without eMMC card. (so i only use SD card) I tried this image: Armbian_21.02.1_Nanopim4v2_focal_current_5.10.12_desktop.img I Wrote to SD with Balena Etcher. After the new installation I turning on my board, I see my two attached .jpg file contents on the screen and after my screen flashes and immediately turns off my monitor (with no signal text on the screen) and if then I can only see Armbian again if I turn my monitor off and after on. So the Armbian is booting in the background, just need an HDMI channel refresh with a monitor physical off and after on. Then I installed all updates ('apt up…

Debian Stretch and Nextcloud 13.0.2 Image available for testing at https://ownyourbits.com/downloads Initial testing shows no problems other that some small adjustments that need to be made for all armbian images: static IP and mDNS. More testing is welcome and feedback appreciated! Cheers, Nacho

Hi, I'm trying to build the Armbian for Rock64. Host machine is Ubuntu 24.04 AMD64 (but it is running in VirtualBox under Windows). Build fails with the following error: [🐳|🌱] Deploying qemu-user-static binary to chroot [ qemu-aarch64-static during image-early ] [🐳|🔨] '/usr/bin/qemu-aarch64-static' -> '/armbian/.tmp/rootfs-232e77ba-e6ab-4067-8029-afd44bd1d0b9//usr/bin/qemu-aarch64-static' chroot: failed to run command ‘/bin/bash’: No such file or directory [🐳|💥] Error 127 occurred in main shell [ at /armbian/lib/functions/rootfs/distro-specific.sh:276 create_sources_list_and_deploy_repo_key() --> lib/functions/rootfs/distro-speci…

Today I upgraded my Helios64, and after reboot it didn't come back. (Waited for 5 minutes or so) After connecting a serial cable (via the USB-C connector), and rebooting, I saw a normal bootloader log (as far as I can see), but no kernel log, just a repeated 'ERROR: rockchip_plat_sip_handler: unhandled SMC (0x82000003)'. I rebooted again, to create a bootlog file, and I saw the same. Then suddenly, after a minute or so, I saw network activity, and my Helios64 was back. Now I have 3 questions. 1) Why didn't it boot twice, and then succeeded? 2) Why is there no kernel bootlog? 3) What is an unhandled SMC? The log ended with …

I checked for any available updates yesterday, and this (linux-u-boot-helios64-current 21.08.1) was applied. Can't find what was new or if it was only a version bump. By the way, nothing broke after the update.

Hi, sorry, prop. a stupid question - but I was so far not figuring out the answer. I have a helios64 running - pretty standard installation, including openmediavault and docker, as described on the kobol help page. I realized that there are some firewall/iptables rules are set, as example: tester@helios64:/etc# sudo iptables -L Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ctstate RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere state NEW,RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp d…

Dear all, I am highly interested in the Helios64 and registered for the next batch. Here are a few questions, I hope that your guys can answer. The OS is Embedded Debian I assume. Questions are quite simple: 1) Hard drive numbering on startup Under Debian, the hard drives in a RAID array are renumbered on each startup by random: /dev/sda, /dev/sdb, etc ... This means that if drive /dev/sdb fails ... it is not necessarily the second hard drive in the bay. I already lost a RAID server extracting the wrong disc in an array. Then I migrated to a Synology NAS and notices that this problem had been fixed as dis…

Hi, I just downloaded the newest release of Armbian and flashed into the SD card, it boots up fine from the SD Card. But I wanna install the system into the Samsung PM9A1 SSD, So I followed the instruction on the armbian page, partioned the drive and made a ext4 filesystem. but I got stuck when I tried to boot up from SSD. I hooked up a serial cable and got this information Any idea about this?

Hello, I have been using Armbian OS on Rock Pi 4B. Full system is on NVME, not using SD card, and there is no eMMC chip on the board. During usage, I needed to shut it down improperly: by removing power cable, not through sudo shutdown now In the end I have following message during boot: Also, here is contents of dev folder: I was wondering if it is possible to fix this error. If not, I will reinstall with new image. Just spent much time on setting the environment, don't want to redo this all I would appreciate any help.

I get Kernel Panics when i do a reboot of the device with the reboot command. I don't get any Panics, when doing a normal boot of the System by powering it. The Panics don't occur on Manjaro. Updating the kernel to 6.1, did nothing for me and the Panic messages are always different and occur at different points of the Boot process. The System runs stable for days, when it boots. I don't have any clues what is going on hear, but i it seems that the device and sdcards aren't broken.

Using P14 in the documentation (https://wiki.kobol.io/helios64/usb/#serial-console) I am unable to get a serial connection to work. Has anyone been able to get UART2 debug Serial working using P14 and an FT232 USB cable? With Kobol plug pulled looking to just have this run in DAS mode over USB-C to still get use without fear but still need to maintain serial console to monitor booting as it sometimes locks up on boot. Downclocking to 1Ghz or below conservative seems to do a lot better but still looking to have remote debug console. When I try to connect I just get the follow error and no output. pl2303_get_line_request - failed: -32

Hello everybody, With 6.18.10-current-rockchip64 and rk3399-kobol-helios64.dtb-6.18.18-opp dtb file, Ok With 6.18.35-current-rockchip64 and overlay helios64 patch with armbian-config, Ko With 6.18.35-current-rockchip64 and k3399-kobol-helios64.dtb-6.18.18-opp dtb file, Ko The crash is random... sometime crash: - At the boot with red system light blinking - At the opening of my LUKS ciffers drives - At a high cpu load - With nothing special, all led are blue, system blinking but network and ssh is Ko Is it possible to explain me how to see the problem or how to have log because I am in blind to have more de…

I am using Debian Image (https://www.armbian.com/orange-pi-5-pro/), USB 3.0 is not working, does not have any power, with original distros or (JR Ubuntu) is USB 3.0 working, any idea how to bring it to life? Thank you Linux orangepi5pro 6.1.75-vendor-rk35xx #1 SMP Fri Jul 19 14:49:03 UTC 2024 aarch64 GNU/Linux admin@orangepi5pro:~$ lsusb Bus 004 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 1a40…

Object: Enable OTG serial console capability( It was enabled by default I think ) What I was checked/tested: g_serial on /etc/modules ttyGS0 on /etc/securetty serial-getty@ttyGS0.service enabled dwc3-0-host enabled/disabled Windows 10 1809 host g_serial recognized R2S as 0525:A4A7(rev0509) Behavior: OrangePi-Zero: Works well( g_serial recognized as same VID/PID but rev0419 ) <== There are no problems on Windows host driver or configurations[ELMO GMAS(5/4/2014, v2.0.0.1) / usbser.sys(v10.0.17763.1)] NanoPi-R2S: Connection fail. Even manual configure 9600 through 115200 bauds. => Putty alerts few m…