Odroid XU4

I see the download page says there are USB 3 issues with the mainline kernel (and eMMC, which the board doesn't even have?) and serial console for legacy kernel is broken. I've also read that HMP isn't supported on mainline either. Which kernel is recommended for general mini server usage with an attached hard drive and the OS installed on the hard drive with SD only for boot? I'm thinking of replacing my old cubietruck with it, running nginx as an SSL web proxy and a little bit of web serving.

i installed the xu4 server (legacy) for debian jessie and get no output on the hdmi/dvi connected display. what is meant by "Serial console enabled" in the description? thank you for producing armbian for odroid xu4! i like the board - it is fast! andrew

Hi, hope you're all doing well. I have this Odroid HC2 (XU4 without video output) that was running an old Armbian version. I intended to update to the latest one (o something close to it) but it seems it won't boot with the newer releases. The board seems to power up ok, leds apparently blinking in a normal fashion, but it seems it gets stuck somewhere. It doesn't acquire any IP address. Not having video output leaves me with little to no way of knowing what is failing. No logs seem to be created in the sdcard. I also tried DietPi images, which I believe are based on Armbian but the same thing happens. I does, howe…

Hi armbian staff and users, i must/try to connect through uart (HC1 /Dev/ttySAC2) to an external uart device. 1. As uart /dev/ttySAC2 is used by boot/kernel, /sbin/agetty has been renamed to stop its launching / lock rather than rebuild uboot/... 2. So as powers supply of 2 uart are differents, 2 converters UART/USB are installed on 2 sides HC1 <-> UART/USB(CP2102N) <=======> USB/UART(XR21V14xy) <-> device. External PS 5v is connected on USB(vcc:gnd), red light on CP2102N is up. I precise 2 points : HC1 <-> UART/USB(CP2102N) <=======> laptop=OK DEVICE <-> UART/USB(XR21V14xy) <=======> laptop=OK Nothing TX/RX, where i…

Hi, I installed Armbian_5.00_Odroidxu4_Debian_jessie_3.10.96_desktop.raw on my ODroid, plugged a 2TB external drive into the USB 3 port, and ran nand-sata-install. I chose /dev/sda1 as the root. After completing, and rebooting, it appears it installed an operating system on /dev/sda1, but I'm still using the SD card as the root: root@odroidxu4:~# mount /dev/mmcblk0p2 on / type ext4 (rw,noatime,nodiratime,errors=remount-ro,commit=600) .... I tried changing boot.ini to point to /dev/sda1: setenv bootrootfs "console=tty1 loglevel=1 root=/dev/sda1 rootwait ro fsck.repair=yes" but it would not boot with this setting. Is there any more information I can p…

Hello, Version 5.4.0-odroidxu4 #19.11.3.342 If I use this command: sudo swapoff -a sudo swapon -a Swap switch off, but not on again. Only after reboot, swap is on again. regards ThomasD

I'm trying to get a full serial console on my XU4. I currently only get the U-boot output. The last message says "Loading Kernel". I never get any kernel related messages. I understand I will need to start up a getty to actually log in via this console port, but I haven't even gotten that far. In my (unchanged) boot.ini I have console=ttySAC2, 115200n8. And when the system boots up, I cannot manually write anything to that port (as i believe the kernel has it opened) Any Ideas? Thanks! Caleb

Ok, so after PHP issues I started off with a fresh armbian install and via armbian-config I installed OMV 4. Install finished without any problems but if I copy stuff via smb the tranfer speed is really bad and I don't know why. On an old install with OMV 3 I used to get nice 100 mb/s. The cpu temp also used to be at like 80 °C during copy, now it looks like this: Following extra options are set in smb.conf: min receivefile size = 16384 write cache size = 524288 getwd cache = yes socket options = TCP_NODELAY IPTOS_LOWDELAY I also checked smbd app, it's running on a big core.... I get the feeling that not all the avaiable resources of my HC2 ar…

Hello everybody, I'm very new to the topic 'armbian' and yet excited. Just played with the BananaPi and downloaded the distro from the first link I got (light/mainline I think). Now I have bought an Odroid XU4 and want to build a Home-Server / NAS with it, wondering which distro to choose. Of course without the heavy-load desktop, but (xenial) next oder default? Thank you. Regards AXEL

after installing armbian on my odroid-xu4-box and about one hour later the screen was going black. But I was not able to get back the running X-Session. So I rebootet as first and as next step I disabled the xdg-screensaver to off, but with no succes - the screen goes black again and neither a moving of the mouse nor a touch the keyboard brings the screan back to activity. So - now what can I do here ? The same behavior appears, if I switch off the screen, if I wanna make a pause for some times. After controlling the xdg-screensaver status I get "off". So it seems, that no screensver is active and running. Which process produces this behavior ? Hope anyone …

Hello everyone, odroid xu4 user here with buster minimal 5.4 from https://dl.armbian.com/odroidxu4/Buster_current_minimal please have a look at the following output ... May 19 12:58:11 localhost kernel: [ 1581.893003] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250) May 19 12:58:12 localhost kernel: [ 1582.352546] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) May 19 12:58:12 localhost kernel: [ 1582.389396] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84) May 19 12:58:12 localhost kernel: [ 1582.426230] mmc_hos…

My board is Odroid HC1 Using balenaEtcher under Windows 10 I have instaled today Armbian_20.05.7_Odroidxu4_buster_current_5.4.50_minimal.img.xz and also was trying before Armbian_20.05.7_Odroidxu4_buster_legacy_4.14.187.img.xz. On both images I wanted to increase verbosity to 7 to see in serial console boot process. Changes in boot.ini are not used during boot until symlink /boot.ini is created which point to /boot/boot.ini Until this is done you will se uboot error that script /boot.ini is not found. Please add this symlink to images for XU4/HC1. Second issue is that editing armbianEnv.txt is not overwriting values in boot.ini. I ha…

Hello, I'm looking for some support with installing plex media server on an Odroid HC1 running the non-desktop stable release of Armbian Bionic. I first used armbian-config to select and install 'plex' but the service didn't start. I then removed the installed 'plexmediaserver-installer' and any created 'plexmediaserver' files/directories & reinstalled manually as shown below: ahaslam@odroidxu4:~$ sudo apt update Hit:1 http://ppa.launchpad.net/bitcoin/bitcoin/ubuntu bionic InRelease Hit:2 http://ports.ubuntu.com bionic InRelease Get:3 http://ports.ubuntu.com bionic-security InRelease [83.2 kB] Get:4 http://ports.ubuntu.com bionic-updates InRelease [88.…

Hi, I get this error message on armbian / omv 4 to mail: "run-parts: /etc/cron.daily/armbian-ram-logging exited with return code 1" Does anyone have a solution?

Hello. First of all, thanks for your work and images working for my board :) I am working on S912 game board (board is used for an arcade game hardware) and would like to install gpu drivers. My issue is I don't find any documentation about from official website (ARM) I also wanted to use Panfrost but no documentation exist for installation :( I visited many site and Learn a little about Deb package and dkms package. Now I have a few questions about Can I install deb without dkms or must I install also dkms? How I can install gpu drivers if files like make don't exist on officia…

Hi, my surveillance webcam stopped working after upgrade to 4.19.14. But only on my HC2. On my other H3-Deviceses, it's working well. System diagnosis information -> http://ix.io/1yko Linux 35708-HC2 4.19.14-odroidxu4 #5.70 SMP PREEMPT Sat Jan 12 18:34:04 CET 2019 armv7l GNU/Linux Error message: root@35708-HC2:~# sudo mjpg_streamer -i "/usr/local/lib/input_uvc.so -d /dev/video0 -n -r 800x600 -f 30" -o "/usr/local/lib/output_http.so -n -w /usr/local/www -p 8080" MJPG Streamer Version: svn rev: 3:172M i: Using V4L2 device.: /dev/video0 i: Desired Resolution: 800 x 600 i: Frames Per Second.: 30 i: Format...........…

Dear All, I don't have much experience with the eMMC, and I wonder if I can flash this image: Armbian_22.11.1_Odroidxu4_bullseye_current_5.4.225.img.xz directly into the eMMC through Etcher, or do you recommend DD instead? Thanks... 🙏

Unable to start docker after update, due to apparmor I used armbian-config's "edit boot-enviroment", added "extraargs=apparmor=0" and after a reboot I still get: docker start portainer Error response from daemon: AppArmor enabled on system but the docker-default profile could not be loaded: running `apparmor_parser apparmor_parser --version` failed with output: error: exec: "apparmor_parser": executable file not found in $PATH Error: failed to start containers: portainer armbianmonitor: https://paste.armbian.com/ebuburoxeh

Hi, I froze kernel to Linux 4.14.222-odroidxu4 as my Odroid-HC1 couldn't be sometime reach with ssh when updating kernel. I get that after reboot and doing apt update, N: Ignoring file '02-armbian-periodic.distrib' in directory '/etc/apt/apt.conf.d/' as it has an invalid filename extension This file is apparently created again as I remove it each time. Laurent

So my sshd service won't start after a system upgrade. I have no uart access, so currently no console access. I do have access to the root drive on a usb device. I suspect systemd is having a problem starting sshd from the ssh.service unit file. But I'm not sure how to fix it. Any suggestions would be much appreciated. Here are the contents of my ssh.service file. I checked that /etc/ssh/sshd_not_to_be_run doesn't exist. I'm a little confused about the runtime directory, so I made a folder in the root directory called sshd with 0755 permissions, but that doesn't seem right. Strangely I couldn't find anything in the syslog file that mentioned s…

Dears, Is there any recent Kodi compilation for XU4 ? Ive build it myself but whenever i try to load it, it gives me an warning saying that GLX/DRI2 is not supported and it also fails to open swrast. The other try i did is to download the .deb package from the mdrjr repository and unfortunately i get the same error. I believe i am missing the right drivers.... By the way, l today was my first experience with armbian... and honestly, i am very impressed. Any ideas ? Best, hippie

Hey guys! I am running Armbian 22.05.3 on my Odroid XU4. Very happy with it. I just installed linux-image-edge-odroidxu4 (kernel 5.17) and rebooted. Everything hunky dory. However, once I'm on 5.17 I am unable to reboot by using the 'reboot' or 'shutdown -r now' commands, which worked on the default 5.4 kernel. Is this a known issue? Any hints on how to debug or any known workarounds? Thank you

As far as I can see on odroid wiki for the lcd and fan enabling the links leads to ubuntu files. I want to install latest armbian for odroid xu4q board and omv5 so I'm wondering if I can use these files or do I need some other files to enable lcd and fan on cloudshell2 + odroid xu4q and armbian?

Hi, On Odroid HC1 512GB SSD with Armbian_20.02.1_Odroidxu4_stretch_legacy_4.14.170 I've got great SSD SATA samba write speed - 110 MB/s! But I have poor only 35MB/s on Armbian_20.02.1_Odroidxu4_buster_current_5.4.19_minimal With Armbian_20.02.1_Odroidxu4_bullseye_current_5.4.19 I have the same poor 35MB/s speed. I've done three identical installations using my checklist: Spoiler #Armbian install on Odroid HC1 # Flash Armbian_<>.img #Upgrade apt update apt upgrade #Move rootfs to SSD # Make rootfs partition fdisk /dev/sda # Make filesystems …

I've tried nand-sata-install on Armbian_22.05.3_Odroidxu4_jammy_current_5.4.199.img and Armbian_22.05.3_Odroidxu4_focal_current_5.4.199.img. Right at the end of running nand-sata-install there's an error. If I try to install anything after nand-sata-install it will hang or the SSD will go into read only mode. To be safe I tested various SD cards and USB to SATA controllers. sed: can't read /boot/boot.cmd: No such file or directory sed: can't read /boot/boot.cmd: No such file or directory Error while creating U-Boot loader image with mkimage umount: /mnt/nand-sata-install.wwpusQ/bootfs: not mounted.

Good Morning! I'm using ODROID-xu4 and did Download your image. I wonder if the image has support for XFS Filesystem? Because I would like to install a Webserber. Grateful! Luis Ferreira

Hello, few days ago I did apt upgrade of my armbian system on Odroid HC2 and there was a reboot req cause of new kernel, so I did reboot it. It wont boot with this error (sorry for missing letters, my LCD is not able to reposition the screen output, attached usb kbd is not working, dont know why, so I just took a pict by my phone): h to partitions #0, OK is current device ing mmc 0:1... /boot/extlinux/extlinux.conf eving file: /boot/extlinux/extlinux.conf ytes read in 2 ms (149.4 KiB/s) Armbian eving file: /boot/uInitrd 776 bytes read in 782 ms (20.2 MiB/s) eving file: /boot/Image d to load '/boot/Image' ing Armbian for failure retrieving kernel T FAILED: con…

Hello, I am the main developer of NextCloudPlus. NCP is a community project to make it easier to run and setup a Nextcloud instance in ARM boards, by providing configuration tools and setup wizards for typical management tasks such as backups, SSL certificates and more. We have just released the first stable version of Armbian based images with NCP for Odroid XU4 / HC1 / HC2. Check it out at the downloads section. More boards will come soon Feedback, testing and development help are very welcome Cheers,

Hi, I've got since several days an issue with armbian-truncate-logs. I received mail alerts from cron as this one, error: error running shared postrotate script for '/var/log.hdd/mysql/mysql.log /var/log.hdd/mysql/mysql-slow.log +/var/log.hdd/mysql/mariadb-slow.log /var/log.hdd/mysql/error.log ' error: error running shared postrotate script for '/var/log.hdd/nginx/*.log ' How to debug that? Laurent

I have my ODROID XU4 configured so that the SD /boot files boot the machine on a SSD formatted to ext4. This works fine with 4.9.30, but fails with the 4.9.33 kernel I installed today. The only useful message I see is that it can't find my SSD's uuid. The uuid is correct so I suspect that the kernel does not have or is not loading a USB driver. Does anyone have a suggestion on how to boot using the 4.9.33 kernel? Thanks, Michael

I used the Armbian 24.11.1 Bookworm Minimal / IOT Image from https://www.armbian.com/odroid-xu4/. When i checked the boot messages with journalctl -b, then i can see the message -> "system vulnerable" Later i can read the message "Spectre BHB: enabling loop workaround for all CPUs". Is this a fix for the first warning message, or is my system vulnerable? Dec 16 20:32:58 odroidxu4 kernel: smp: Bringing up secondary CPUs ... Dec 16 20:32:58 odroidxu4 kernel: CPU1: thread -1, cpu 1, socket 1, mpidr 80000101 Dec 16 20:32:58 odroidxu4 kernel: CPU2: thread -1, cpu 2, socket 1, mpidr 80000102 Dec 16 20:32:58 odroidxu4 kernel: CPU3: thread -1, cpu 3, …

Hi! short question: Best way to create a bootable clone of sd card? I did some reading and found ">>create image on windows >> shrink image via gparted" doesn't work for me since I dont have a second computer running linux (will the linux subsystem on windows 10 help?). In the past, I used the rpi-clone on a raspberry, but reading in this forum has taught me that hotcloning an armbian sd card via script is not necessarily safe. Computers availabel to me are: 1) odroid hc2 running armbian 2) acer laptop running windows 10

Hi Guys, I tested both the odroid official and armbian images for the XU4. Both run well, but I prefer the armbian image. I have attached my 800x480 hdmi display, it works, but there's a purple line at the left side of the display. ( I think it's one pixel wide) This is not the case with the odroid official image, so I guess it's a configuration issue. I took a look at the boot. ini file, but I don't see anything that rings a bell. Can somebody point me to the right direction?

Hi, I want to try out my Odroid HC2 as an openvpn client. I don't expect great performance but I want to make sure I set it up correctly. This is why I want to ask if anyone can give any recommendations or tweaks for using it as an openvpn client. Idk much about openvpn, I know it uses openssl for de and encryption. Is there a way to use hardware de and encryption so I can speed things up and have a better download speed via openvpn? Or is hw de/encryption maybe already used by default if I just install openvpn package? Any recommendations on how to correctly set this up are appreciated.

I recently hooked up my XU4 to a DVD/CD Enclosure, essentially just SATA to USB, and am having an issue mounting the drive. After researching online it seems this is a filesystem issue. So, I was wondering if anybody else has encountered this problem, and if so, how did you fix it? Thanks Armbian: Image: Armbian_5.37_Odroidxu4_Ubuntu_xenial_next_4.9.71_desktop.7z Kernel: [default] 4.9.61-odroidxu4 #2 SMP PREEMPT Wed Nov 22 16:34:23 CET 2017 Errors: # mount -t iso9660 /dev/sr0 /media/ceru/cdrom mount: /dev/sr0 is write-protected, mounting read-only mount: wrong fs type, bad option, bad superblock on /dev/sr0, missing co…

$ systemctl status ● henry State: degraded Jobs: 0 queued Failed: 1 units Since: Sat 2022-12-03 10:19:04 GMT; 24h ago $ systemctl list-units --failed UNIT LOAD ACTIVE SUB DESCRIPTION ● logrotate.service loaded failed failed Rotate log files $ journalctl -u logrotate.service Journal file /var/log/journal/c87d7c4913d949949100f089ec48b092/system.journal is truncated, ignoring file. -- Journal begins at Sun 2022-12-04 00:00:06 GMT, ends at Sun 2022-12-04 10:33:57 GMT. -- Dec 04 00:00:06 henry armbian-ramlog[2714]: /usr/lib/armbian/armbian-ramlog: line 153: /var/log/./journal-20220019-00:00:05/c8> Dec 04 00:…

I am now testing armbian on my XU4 and...AMAZING...I have very little fan noise. I am using the Noctua fan as per; http://forum.odroid.com/viewtopic.php?f=65&t=15310 and I haven't even implemented the fan control script [yet]; https://github.com/nthx/odroid-xu3-fan-control Silence is golden... armbian ROCKS!

I just got a new XU4 and I tried to run both the official ubuntu 18.04 image with linux 4.14 and the armbian stretch 4.14 image (both minimal). I can hear a constant electrical squeaky noise (similar to noise from certain power supplies, usb chargers, etc) coming from the XU4 when running Armbian. The same noise is not present in the Ubuntu image. This occurs immediately after first boot (no additional configuration) and is constantly there. This is especially noticeable when the fan is off. Has anyone experienced this before?

Today I wanted to upgrade from jessie to stretch, I'm following this website. After changing the word jessie to stretch in /etc/apt/sources.list and in every file in /etc/apt/sources.list.d/* I noticed that changing the omv-extras-org.list from: # OMV-Extras.org deb https://dl.bintray.com/openmediavault-plugin-developers/erasmus jessie main # OMV-Extras.org Testing deb https://dl.bintray.com/openmediavault-plugin-developers/erasmus-testing jessie main to # # OMV-Extras.org deb https://dl.bintray.com/openmediavault-plugin-developers/erasmus stretch main # OMV-Extras.org Testing deb https://dl.bintray.com/openmediavault-plugin-developers/erasmus-testing stre…

I am trying to set up serial communications over the CON10 connector (UART0 pins 4,5,6,8) to another board (BeagleBone Black) to transmit data parsed as strings between the boards. Based on this link, this should correspond to /dev/ttySAC0. I have been unsuccessful in achieving communication via these pins and device node. In using setserial to probe the port settings, I was concerned about the following output: setserial /dev/ttySAC0 /dev/ttySAC0, UART: undefined, Port: 0x0000, IRQ 83 In using dmesg to probe for more information, I found an identifier for SAC0: dmesg | egrep -i 'serial|tty' [ 1.020896] [c4] 12c00000.serial: ttySAC0 at MMIO 0x12…

Hi! I'm attempting to activate FS-Cache on a HC2 with a 512GB SSD. I want to cache reads from other servers with NFS shares using mechanical HDDs over GbE. I run PLEX on the HC2 with SSD and the media is stored on other HC2s running OMV, with big mechanical HDDs. I figure that I can use a good chunk of the SSD to reduce the network traffic and the HDD use. I successfully use FS-Cache on a Ubuntu 18.04 laptop, together with autofs. But when I attempt to start FS-Cache on my HC2 with Bionic Armbian I get: Oct 17 23:25:34 ctrl systemd[1]: Starting LSB: CacheFiles daemon... Oct 17 23:25:34 ctrl cachefilesd[11217]: * Starting FilesCache d…

I’m relatively new to Armbian, have been running it with XU4 for couple of months. Otherwise working very well, but there’s occational (once a month) full system hang/crash or something. This is a remote server with constant load (video surveillance) and when it happens, all connectivity is of course lost and I think it can be only resolved locally with full power cycle. I’ve not yet tried to attach HDMI monitor when it’s in the crashed state, but will do it next time. Although not very optimistic if that works at all. There are nothing obvious in the logs, or it might be that I don’t know where to look. Are there any general advice what to do, how to figure this out?…

I already posted the question in the Odroid forum. I decided to post it here too since it may be more inherent to the Armbian OS. I used both Armbian_23.02.3_Odroidxu4_bullseye_current_5.4.239.img from the odroidxu4 archive and Armbian-unofficial_23.11.0-trunk_Odroidxu4_bullseye_current_6.1.63 generated from the Armbian build script. (Base CLI Image). After flashing the former image and then installing OMV6, this is the output that OMV6 gives me when installing the openmediavault-wireguard plugin: Spoiler Reading package lists... Building dependency tree... Reading state information... The following additional packages will be in…

OK, so while documenting the Armbian patch process I needed something actual to patch. I added gpio-line-names to the device tree, so now all lines are defined. Once I finish the documentation I'll PR this patch. No more guessing what physical pin is! At some point it might make sense to put in jumper and physical pin #. Spoiler gpioinfo gpiochip0 - 8 lines: line 0: "GPY7.0" unused input active-high line 1: "GPY7.1" unused input active-high line 2: "GPY7.2" unused input active-high line 3: "GPY7.3" unused input active-high line 4: "GPY7.4" unused input active-high …

Hi, I am running Armbian on four HardKernel HC2's and everything is working perfectly. The four SBC's are running a Moosefs cluster running Ubuntu 18.04 and Armbian 5.85, and this leads to my questions: I am trying to decide whether to upgrade as apt is proposing moving to 5.89 The change log does not currently list 5.89 and shows 5.87 as the newest. Am I missing something? When I look at previous change logs it is difficult to decipher which fixes impact the HC2/HC1/XU4. Is there an easy way to tell? How do you decide when to upgrade? Is it even worth upgrading when running more mature boards like this one? My boards run insi…

Just doing maintenance tonight on my boxen, regular `apt upgrade && apt update` on ODROID-XU4 and I noticed Debian upgraded to latest kernel (5.8 or whatever). I go look in boot and notice `uInitrd' is pointing at the new Debian version (instead of Armbian version): drwxr-xr-x 4 root root 4096 Nov 15 19:53 . drwxr-xr-x 22 root root 4096 Nov 15 19:50 .. -rw-r--r-- 1 root root 65 Nov 15 19:28 armbianEnv.txt -rw-r--r-- 1 root root 1536 Jun 4 15:24 armbian_first_run.txt.template -rw-r--r-- 1 root root 38518 Jun 4 15:24 boot.bmp -rw-r--r-- 1 root root 4882 Jun 4 15:24 boot-desktop.png -rw-r--r-- 1 root root 12479 Jun 4 …

Hello, i saw a post regarding ZFS > zfs What is the current state of ZFS support? Is it a stable to run ZFS as FS for root fs only on SD card (16-32GB)? I need that for an easy backup on FS level using send/rec commands. But as we know xu4 is 32bit only - > maybe problem with stability - stability 32bit official solution but for rpi4 Or maybe is there a point to use zfs for root fs at all? what about LMV? thanks

Greetings, As the subject says... CEC not detected in kernel, cec-client throws errors, nothing I tried worked. root@odroidxu4:~# uname -a Linux odroidxu4 5.4.239-odroidxu4 #1 SMP PREEMPT Thu Mar 16 15:52:54 UTC 2023 armv7l GNU/Linux root@odroidxu4:~# cec-client -l libCEC version: 6.0.2, compiled on Linux-4.19.0-14-armmp-lpae ... , features: P8_USB, DRM, P8_detect, randr, Exynos, Linux, AOCEC Found devices: 1 device: 1 com port: Linux vendor id: 0000 product id: 0000 firmware version: 0 type: Linux root@odroidxu4:~# cec-client No device type …

Odroid XU4 / Armbian 22.02 Bullseye USB3 sata drive gets randomly disconnected: (every 8 hours or so when constantly reading / writing) [44676.709229] sd 0:0:0:0: [sda] tag#24 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN [44676.709252] sd 0:0:0:0: [sda] tag#24 CDB: opcode=0x28 28 00 49 a5 1b d8 00 00 08 00 [44681.728962] xhci-hcd xhci-hcd.8.auto: xHCI host not responding to stop endpoint command. [44681.749158] xhci-hcd xhci-hcd.8.auto: xHCI host controller not responding, assume dead [44681.749210] usb 4-1.2: cmd cmplt err -108 [44681.749509] xhci-hcd xhci-hcd.8.auto: HC died; cleaning up [44681.749696] usb 3-1: USB disconnect, device numbe…

Hey Can anyone confirm the problem with under-clocking in Odroid HC1/HC2/XU4 with Kernel 4.19.14 / Armbian 5.70? I could always reach 2000/1500Mhz without a problem. Currently, after the last Armbian update from 5.60 to 5.70, I noticed a strange behavior that Odroid does not want to reach full clocks. With cpufrequtils min 600 max 2000 and "performance" and clocks do not want to go higher than 1800/1300Mhz temperature cpu 45.0 ° C. No changes just last updates nothing more was touched. After returning to 5.60 and 4.14.69 the CPU runs normally at 2000/1500 .... I also have the impression that HDD sometimes behaves strangely at 5.70 / 4.19.14 …

Hi, I am trying to get my Xu4 to boot from an emmc card, I am using Armbian Bionic mainline kernel 4.9.y. I can write this to SD card, and it boots and runs OK. I prepared the emmc card using the inbuilt system nand-sata-install script. The emmc card will not boot. I tried a couple of other iso.s same non result. Checking the forum I found this thread started last year:- This thread was HIJACKED by Tkaiser , who turned it into a discussion about OMV, and I cannot see a successful conclusion to the original boot problem! Please can you advise me of the method to get my emmc card to boot on my xu4, using the curre…

I know it is unsupported and all, but I just want to point out that running Ubuntu Focal(2020/05/03) with kernel 5.6 on Odroid MC1 has been destroying microSD cards. The board boots up fine, but after an apt-get update and a few minutes in, the Sandisk microSD card died and becomes read-only. I'm not sure if it is vendor-dependent, but I have tried out two new Sandisk microSD cards and they all turned read-only. This might be a kernel issue since on Debian Buster with kernel 5.4 or kernel 4.14 that never happened.

Hi, I really like the OS but notice that while operating the fan never turns on. It does spin when first powered up but never after that while running. Is there something additional i need to add to get the fan to operate? Thanks

Looking at various Docker images on Docker Hub, I see images for armv6, armv7, and armhf. Which are the right ones to use on an XU4/HC2?

I’m running jammy and (I think) I’d like to upgrade to bullseye. But I can’t find a procedure for doing so. I’m guessing I can’t just dist-upgrade since jammy is Ubuntu and bullseye is Debian? I’ve googled for a procedure and searched this forum as well but I’m not finding a procedure. While searching this forum, I saw lots of topics where people had problems after upgrading to bullseye. Should I even do the upgrade? I don’t have much invested in the jammy install so far. Aside from running through armbian-config and getting all the settings the way I want them, the only things I’ve done are 1) installed Docker and 2) installed docker-compose. The latter was …

Hi there, I'd like to understand the best way to handle updates on Armbian… My OS is: odroid ) uname -a Linux odroidxu4 5.4.225-odroidxu4 #22.11.1 SMP PREEMPT Wed Nov 30 10:55:16 UTC 2022 armv7l GNU/Linux odroid ) lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 11 (bullseye) Release: 11 Codename: bullseye And APT says: The following packages have been kept back: linux-dtb-current-odroidxu4 linux-headers-current-odroidxu4 linux-image-current-odroidxu4 linux-u-boot-odroidxu4-current The habits tell me to update however the experience taught that I could breaking somethin…

Hi The problem with Odroid HC1 is that BIG cores cannot go higher than 1.50Ghz and LITTLE cores cannot go higher than 900Mhz! Why is the CPU so throttled now? This sbc can and could work at higher clock speeds without any problems. Forcing 2Ghz and 1.50Ghz via cpupower does not help... Bullseye A 23.8.27 K 6.6.31

Is it possible to transfer the entire Armbian system from SD card to HDD? ... it is known that the SD card has a lower endurance than such a HDD dist (write, read etc.) I tried to transfer the system in such a way that I first upgraded the kernel to the newest one on the SD card and then moved the system files to a partition on the HDD: mount /dev/sda1 /mnt time tar --one-file-system -cpf - / | (cd /mnt && tar -xpf -) then knowing the sda1 partition information and ID lsblk -f then knowing the sda1 partition information and ID I changed the UUID / HDD number in two locations nano /boot/boot.ini and nano /etc/fstab after rebooting…

After latest upgrade 21.05.01 apt says linux-buster-root-current-odroidxu4 is obsolete now and could be removed with autoremove. But even this version was installed with same upgrade, so i wonder why it should be removed now? Should i really remove that package? Thx

After switching from Debian Buster (installed via Petitboot) to Armbian, I have problems with NFS on Openmediavault that didn't exist the weeks before. My NFS streams abort after a few minutes, sometimes seconds (on Libreelec as well as Kodi for Windows). In OMV it shows me that the service is enabled and running, but systemctl says: nfs-server.service loaded active exited. With exportfs -rav it runs again, only to stop after a few minutes. It also works without command if I wait a few minutes. I also did a fresh install of Armbian, wich did nothing.

Hi all, My Hard Drive in my HC2 is not found or not readable. Before I was on Armbian Buster with Kernel 4.14 and everything was working fine. I switched and am now running Armbian Focal 21.05.2 with Kernel 5.4.116 . HDD is btrfs formatted. /proc/filesystems lists btrfs so this is not the problem. /dev/sda exists, but sda will not be listed when I lsblk. Dmesg shows a Read Capacity(16) failed. Not posting the whole dmesg log b/c armbianmonitor is attached. Grateful for any help or hints =)

Hi, I lose hdmi output if I unplug the hdmi cable and plug it again .. I can still access the odroid via ssh.. Any help is greatly appreciated !

hello, during ansible-fact-gathering following errors are logged. no instability has been noticed. uname -a Linux nas 4.9.46-odroidxu4 #10 SMP PREEMPT Fri Sep 1 05:29:13 PDT 2017 armv7l GNU/Linux Sep 06 15:02:36 nas ansible-setup[28480]: Invoked with filter=* gather_subset=['all'] fact_path=/etc/ansible/facts.d gather_timeout=10 Sep 06 15:02:37 nas kernel: Unhandled fault: asynchronous external abort (0x1211) at 0x00000000 Sep 06 15:02:37 nas kernel: pgd = e69ccc80 Sep 06 15:02:37 nas kernel: [00000000] *pgd=42c04003, *pmd=00000000 Sep 06 15:02:37 nas kernel: Unhandled fault: asynchronous external abort (0x1211) at 0x00000000 Sep 06 15:02:37 nas kernel: pg…

Hello. I freshly installed bullseye from the other supported variant links for an odroid XU4. When trying to get docker daemon running, it looked like the ip_tables module and br_netfilter modules weren't available in the kernel. I think I have sorted out ip_tables (modprobe doesn't return any problems now), but docker's daemon is still showing a problem when running dockerd (with debug level info in the daemon.json file): Running modprobe bridge br_netfilter failed with message: modprobe: WARNING: Module bridge not found in directory /lib/modules/5.19.10-armmp-lpae When executing systemctl status docker.service ... …

Hi, I was wondering if there is a build of Armbian for the Odroid xu4 with a more recent Linux version. I currently have 3.10. It is super old ... Thanks in advance

A known issue with the Odroid XU4, HC1, and HC2 is that it (uboot?) does not properly park the hard disk heads before/during shutdown or power cycle/off. So, the disk drive is forced to emergency hard retract the heads when power is shutdown/cycled. This is of course a violent action for the HDD and should be avoided. Use this odroid.shutdown script and install into /lib/systemd/system-shutdown/. https://wiki.odroid.com/odroid-xu4/troubleshooting/shutdown_script Recommend adding to armbian for XU4 distros.

Hi all! I am running a nextcloud server on an odroid HC2 and a 4 TB WD red HDD. So far, so good (thanks again @Igor for the quick help with the kernel downgrade!). And since I have bought the sbc recently, I do not seem to have the older firmware version with the HDD "emergency power down" bug, i.e. I haven't heard clacking sound from the HC2. Today, I set HDD spindown to 1 hour via hdparm (wd red does not support apm) because the HDD would spin down after about three minutes on its own. The HDD does not seem to apply these settings, so I installed smartmontools to check the HDD in general. Only to find that: smartctl -a /dev/sdb1 gives this…

When I run the Linux kernel on the Odroid XU4 board, it enters a loop with this error during boot: U-Boot 2017.05-00008-g6a9ddb8303-dirty (May 19 2020 - 19:48:01 +0900) for ODROID-XU4 CPU: Exynos5422 @ 800 MHz Model: Odroid XU4 based on EXYNOS5422 Board: Odroid XU4 based on EXYNOS5422 Type: xu4 DRAM: 2 GiB MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1 MMC Device 0 ( SD ): 29.7 GiB mmc_init: -5, time 4 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Press quickly 'Enter' twice to stop autoboot: 0 reading /boot.ini 2401 bytes read in 4 ms (585.9 KiB/s) ## Executing script at 43e00000 reading config.ini…

Guys, how can I install Mali's X11 userspace driver for desktop, web browser and video hardware acceleration Thanks in advance.

Hi! my nextcloud instance on an odroid hc2 running armbian has been running stable and smoothly for several months now. Thanks Igor and the whole armbian team! I have one question though: Task: I convert videos with ffmpeg to reduce file size and optimize them for streaming observed behaviour: the CPU is getting very hot! In the evening up to 100 °C (see below), but at noon I have seen temperatures of up to 115 °C! I read somewhere that 110 °C is the critical temperature for the board and the stock hardkernel image has an emergency shutdown implemented. But my board running armbian seems to be negligent of this. On a side no…

I attempted to file a bug using `reportbug`, but since the kernel package is from Armbian and the report went to Debian, I assume that is a dead end. https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1137721 I will mostly copy/paste from that report, here, but I also ran `armbianmonitor -u`. https://paste.armbian.com/wenegucita I run a home backup server with a 1TB SSD attached to an ODroid HC1 board. There is no redundancy, but I do keep a limited history of snapshots, taken hourly and trimmed down to a small number of hourly, daily, weekly, monthly, and yearly snapshots. There should be at most about 20 snapshots ex…

Try to upgrade from 25.5.1 but base-files not present in repository. Missed again. @Igor can you fix it?

Hi All, I've just got the new Orange Pi R1 and as expected it's working just well with the Orange Pi Zero armbian image. The only thing I'm struggeling with is the Wifi driver. The driver compiles succesfully but it seems that the kernel needs patching as well: ... CC [M] /usr/src/rtk8189es-2015-12-15-90ed86d42d/rtl8189ES//hal/OUTSRC/rtl8188e/phydm_RTL8188E.o CC [M] /usr/src/rtk8189es-2015-12-15-90ed86d42d/rtl8189ES//platform/platform_ops.o CC [M] /usr/src/rtk8189es-2015-12-15-90ed86d42d/rtl8189ES//platform/platform_ARM_SUNnI_sdio.o CC [M] /usr/src/rtk8189es-2015-12-15-90ed86d42d/rtl8189ES//core/rtw_mp.o CC [M] /usr/src/rtk81…

Just using ubuntu and want to change to ambian ASAP

Hi, please, which core are You using on odroid HC2? I am running on HC2 only openmediavault, but i will try nextcloud in the docker - which core image is better for?

Hi all, I am trying to add SSH Keys to an HC1. The commands I am using are: sudo mkdir ~/.ssh sudo chmod 700 ~/.ssh sudo nano ~/.ssh/authorized_keys Then I select all the PUBLIC key from PuTTy Gen and copy/paste it on the file above, close and save the file. sudo chmod 600 ~/.ssh/authorized_keys sudo chown -R $(whoami):$(whoami) ~/.ssh/ sudo reboot I then try to SSH with PuTTy and SSH keys. Immediately I get an error saying "Server refused our key" and then it asks me for my normal password as a user. Any idea what I am doing wrong?

Dear Readers I had quite some troubles migrating my armbian system from an SD-Card (16GB) to my emmc (32GB). I'd like to sum up my journey for future travelers ;-) I was not successful simply copying the image of the sd to the emmc and resizing the partition. It would not boot. Apparently emmc has additional boot partitions which must be set correctly. I "repaired" the emmc with this https://wiki.odroid.com/accessory/emmc/recovery_xu4 and it booted Android all right from emmc. I then rebooted on my SD-Card and used the nand-sata-install command to "Boot from eMMC - system on eMMC". It took some time to copy, but when booting on the emmc, still Android…

hi, I am VERY happy with how 4.9 is running odroid-xu4. as i use it as media server and player wanted to see if i could get latencies (poitential) down by applying latest RT patches that are in line with current xu4-next kernel sources. added pathes to userpatches/kernel/odoirdxu4-next directory, build process went fine, have selected FULL-RT but it does not boot (final image) source: https://github.com/hardkernel/linux/tre ... dxu4-4.9.y rt-patches: https://www.kernel.org/pub/linux/kernel ... ts/rt/4.9/ it compiles ok but it does not boot ... has anyone looked at what the issue might be ? i don't have serial debuigger yet, have ordered bu…

Please forgive me if it is a stupid question, but what is preventing us from keeping n previous kernels installed in case an update is broken and does not boot? Fedora does it, Ubuntu does too. In general it should be simpler to boot a previous kernel than to try to pull the SD card and fix it in a second machine.

Hi .. I try to upgrade to latest armbian. I run now bionic Only when i do sudo apt-get-dist-upgrade i get no upgrade options. I was thinking i need to chage somewhere in setting something with tls. Only... So i cannot find a wiki or a other good working how to. So please can some help me to get my xu4 update tot latest version.. Or give me a good wiki or a working how to. Thanks!!

I decided to klipperize an old 3d printer and found some of my orange pi boards dead, so i ended up selecting my XU4 for the task. Fast forward 24 hours and i'm fighting MCU timeouts. Klipper doesn't know what happened just that the mcu stopped responding. And their knowledge base article is basically "gosh it could be anything". One seat of the pants observation i made was that the XU4 idles along at 600mhz with a load average of about 0.1 and it seemed like the load average increased maybe before the mcu stopped responding. The MCU in question is an SKR Pico, aka rp2040 with a usb connection. The mcu is not receiving power from th…

I am a noob on Linux (unfortunately). I run a Xu4 with armbian on it. On the Xu4 i run Domoticz, my home automation system. Something is eating my hdd space; a fixed amount is used up every hour. I set up a new system with a bigger sd but I want to get to the bottom of the issue. I do not know how I can see what the Xu4 does every hour. Perhaps a log or a backup? Perhaps my OS is doing something, or perhaps my Home automation. I do not run any script to make periodic backups or anything else like that. How can I figure it out? Thanks!

Hi all, I'm running a couple of ODroid XU4's as a server. Yesterday I ran an update and after this update the board no longer boots... (I was running Armbian Focal kernel 4 I have tested a 'fresh' armbian image and then the system boots without issues. I have saved what packages are updated and wonder if I would be able to restore this somehow? A log of the update (never mind the dutch) https://pastebin.com/WWP2DFfC I used to have kernal 5.4 on this board, but I downgraded about 6 months ago. Could that be the issue? Because in the log I read: Uitpakken van .../77-linux-image-current-odroidxu4_21.02.2_armhf.deb wordt …

yo guys, not sure how to fix this one, so i keep getting an adittional IP on my ethernet interface while i assigned it to static... tried to assign static conf with the armbian-config thing and by editing the /etc/network file. my dhcp is the stock ISP router network. never had this problem before, even when using other images from diferent distros. also sudo armbianmonitor -u gives me this error System diagnosis information will now be uploaded to /usr/bin/armbianmonitor: line 859: [: -gt: unary operator expected

Hello everybody, I have been having an issue lately with my Odroid XU4 running Armbian's Ubuntu Xenial server. The problem is that the ethernet interface would only be detected every once in a while upon a reboot of the system, however, after performing an update earlier today, the ethernet interface is not detected no matter how many times I reboot the system or mess with settings. Please help as I'm sort of a noob with debugging linux issues and this is the main interface for my mini-network. Huge thanks in advance. UPDATE: Apparently the update caused the device name to switch from eth0 to enx001e06311a69 and by reconfiguring my servers to use that interface it…

Hi, I'm trying to run weston on Odroid XU4, but it does not start. Seems something is wrong with GPU drivers. I have installed "Armbian 25.2.1 Bookworm Minimal" image and then installed weston via apt. Then, trying to run the weston fails with error: Date: 2025-04-13 UTC [13:47:44.248] weston 10.0.1 https://wayland.freedesktop.org Bug reports to: https://gitlab.freedesktop.org/wayland/weston/issues/ Build: 10.0.1 [13:47:44.249] Command line: weston [13:47:44.249] OS: Linux, 6.6.81-current-odroidxu4, #1 SMP PREEMPT Mon Dec 30 15:59:39 UTC 2024, armv7l [13:47:44.249] Flight recorder: enabled…

Is there a repository with older Armbian images available? I'm looking to install OMV6 on my Odroid HC1 (XU4), when I get Armbian Bookworm installed OMV scripts says to use Buster or Bullseye, but I cannot find an Armbian Bullseye image anywhere. I'm not super proficient with Linux (I know enough to get myself in trouble) so compiling my own image is not something I think I can do. Any help would be greatly appreciated. Edit: Nevermind...I'm an idiot...didn't notice the GIANT button for Archived Images. Apologies. Thanks, Robert

So I tried switching my MMIO GPIO to /dev/gpiomem from /dev/mem and it doesn't appear to support the GPZ block https://wiki.odroid.com/odroid-xu4/hardware/expansion_connectors#con_11_-_2x6_pins The address is 0x03860000. Hard Kernel's wiringPi doesn't seem to support this either. Should this be a question I ask Hard Kernel folks? https://wiki.odroid.com/odroid-xu4/software/gpio_register_map

Hi, I have been running Armbian Buster on an Odroid HC1 for a while but today one upgrade is held back: The following packages have been kept back: libc-dev-bin 0 upgraded, 0 newly installed, 0 to remove and 31 not upgraded. This is why: $ sudo apt install libc-dev-bin Reading package lists... Done Building dependency tree Reading state information... Done The following package was automatically installed and is no longer required: linux-libc-dev Use 'sudo apt autoremove' to remove it. Recommended packages: manpages manpages-dev The following packages will be REMOVED: armbian-config build-essential g++ g++-8 libc6-dev libstdc++-8-dev…

Newbie question I would like to clone a hdd to a new ssd without reinstalling the system. What are the ways to do it on my Odroid-HC1 running Armbian Stretch with boot partition on a SD card? Thanks

I have an array of HC2's running lizardfs. The other units are running 5.4.72-odroidxu4 kernels, but I dared to upgrade one to 5.8.16-odroidxu4 Only this one unit threw a Since the other units didn't I show anything in their logs, I have to assume it isn't because a process running away or a memory leak. line of fstab to mount the spinning rust drive: UUID=be95e207-1768-4fd9-bda9-ddc126a47d50 /chunks/be95e207-1768-4fd9-bda9-ddc126a47d50 xfs rw,noexec,nodev,noatime,nodiratime,largeio,inode64 0 2 Can't think of any additional info that would be useful. If someone has suggestions, i would be interested.

Hi all, I wanted to do some cross arch builds on my newly installed Armbian on an Odroid-HC1 buuut, it seems binfmt_misc support is not enabled in the kernel. Can I enable it somehow without recompiling the kernel? Thank you for this great image, kernel 5.4, omg!

Spoiler [58531.860637] lowmem_reserve[]: 0 0 0 [58531.860654] Normal: 56*4kB (H) 44*8kB (H) 48*16kB (H) 37*32kB (H) 14*64kB (H) 1*128kB (H) 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 3552kB [58531.860733] HighMem: 27*4kB (UM) 42*8kB (C) 1*16kB (C) 0*32kB 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 460kB [58531.860786] 304403 total pagecache pages [58531.860790] 15267 pages in swap cache [58531.860794] Swap cache stats: add 382457, delete 367190, find 125239/202183 [58531.860798] Free swap = 1630472kB [58531.860801] Total swap = 2097148kB [58531.860805] 518656 pages RAM [58531.860809] 322048 pages HighMem/MovableOnly [58531.860813] 8201 pages re…

Hello everyone, I'm wondering if is possible to include in future releases of the Armbian Kernels these options: CONFIG_NETLABEL CONFIG_MPTCP CONFIG_NET_VRF CONFIG_OF_UNITTEST CONFIG_OF_DYNAMIC CONFIG_OF_OVERLAY CONFIG_INET_MPTCP_DIAG CONFIG_MPLS_ROUTING CONFIG_MPLS_IPTUNNEL CONFIG_NLMON CONFIG_NET_VRF CONFIG_GTP CONFIG_GENEVE CONFIG_IPVTAP CONFIG_IFB I'm playing around with my Odroid XU4 and I notice that I'm missing such options and drivers compiled in the Kernel. As an example Debian has these options enabled by default. In my case I created a script that is gett…

Hi All, I might need your help with one issue I've encountered. I'm running debian with the 4.9.20 kernel on an Odroid XU4 board. I've compiled the kernel with the options for AppArmor enabled. The installed AppArmor version is the 2.10.95 (auditd is also installed in version 1:2.4-1+b1). ## Kernel Options ## CONFIG_SECURITY=y CONFIG_SECURITYFS=y CONFIG_SECURITY_APPARMOR=y CONFIG_SECURITY_APPARMOR_BOOTPARAM_VALUE=1 CONFIG_DEFAULT_SECURITY_APPARMOR=y CONFIG_DEFAULT_SECURITY="apparmor" CONFIG_SECCOMP=y CONFIG_SECCOMP_FILTER=y CONFIG_AUDIT=y ## ## AppArmor itself is working without any issues. If I set…

Hi! my odroid HC2 is running pretty great on armbian 5.90 for >1,5 years (24/7) now. Running a nextcloud instance, with decent perfomance, even when clocked to 600/1200 Mhz in the summer, because of one (1) crash, that I think might have been heat-related. The thing I'm wondering about: in htop, it shows only ( .LITTLE) cores for eight lines, but the cpu is a (.big.LITTLE) architecture and my other HC2 sbc, which runs armbian 20.02.7, show "(.big.LITTLE)" in htop. Perfomance in sysbench is equal on both boards, so this might mean nothing, but it still seemed strange to me. Anyone knows why htop only shows "( .LITTLE)" cores?

I got my HC2 yesterday and am quite satisfied with it. I'm using the latest Armbian Stretch release. The spin-down of my 3TB WD Red was solved by a firmware update. Unfortunately there are still some errors in the error output (journalctl -p 3). Maybe you have a hint how I can solve it: Nov 03 18:16:42 NAS kernel: CPU4: Spectre v2: incorrect context switching function, system vulnerable Nov 03 18:16:42 NAS kernel: CPU5: Spectre v2: incorrect context switching function, system vulnerable Nov 03 18:16:42 NAS kernel: CPU6: Spectre v2: incorrect context switching function, system vulnerable Nov 03 18:16:42 NAS kernel: CPU7: Spectre v2: incorrect context swit…

Estoy perdido, despues de buscar y buscar soluciones, soy nuevo en este foro. He probado xu4fan, fancontrol, incluso un script que está en este foro, y no puedo iniciar el ventilador con armbian, ni siquiera puedo hacer que el ventilador se mueva. he intentado esto PUNTO_VIAJE_0=25000 PUNTO_VIAJE_1=30000 PUNTO_VIAJE_2=40000 echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone0/trip_point_0_temp$ echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone1/trip_point_0_temp$ echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone2/trip_point_0_temp $ echo $TRIP_POINT_0 > /sys/…

W: Size of file /var/lib/apt/lists/apt.armbian.com_dists_jessie_jessie-utils_binary-armhf_Packages.gz is not what the server reported 5780 5784 W: Size of file /var/lib/apt/lists/httpredir.debian.org_debian_dists_jessie-backports_main_binary-armhf_Packages.gz is not what the server reported 1122303 1123712 Get this when first doing apt update after fresh install. HC1 Jesse. I assumed at first it was network error, but this is consistent. Have downloaded and checksummed successful. Assumed then it was the SD card, replaced and have now tried several. Power supply is solid. I believe the hardware and bandwidth / router are fine. Simply repeat ap…

abm.tar.gz