Orange Pi 5

Loading the latest dist with 5.10.160 kernel, the header package has wrong version...

With the prior image and kernel 5.10.110 I was able to run compile.sh and produce the linux-source-legacy-rockchip-rk3588_23.02.0-trunk_all.deb which provided the kernel source in /usr/src/linux-source-5.10.110-rockchip-rk3588.tar.xz. I downloaded the latest img which provides kernel 5.10.160 which booted fine. However, running the same compile.sh process I used previously with success produced the older deb package that contains the 5.10.110 kernel source. There were a couple of errors displayed. My compile.sh command is: ./compile.sh BOARD=orangepi5 BRANCH=legacy BUILD_ONLY=kernel RELEASE=jammy KERNEL_CONFIGURE=no The first error encountered was …

I was able to flash armbian bookworm cli to the ssd using balena etcher but when I boot the OPI5 from the sdcard and run lsbk it can only see the sdcard any ideas ...

My experience so far: 1. Booting up (Jammy/Bullseye) from SD, HDMI out to 1440p display cuts off text at the bottom. It affects installation and later use. I need to press ENTER several times to all questions until text moves up in the buffer and becomes visible, and then blindly type the answer to proceed to the next step, then several ENTERs to scroll again, and so on. Looking at fbset and stty output: me@opi:~$ fbset -i mode "2560x1440" geometry 2560 1440 2560 1440 32 timings 0 0 0 0 0 0 0 accel true rgba 8/16,8/8,8/0,0/0 endmode Frame buffer device information: Name : rockchipdrmfb Address : 0 Size …

I noticed the new images with 23.5 but I have an older installation, then went to nightly, I just switched back to the official, I ran dist-upgrade but when I boot, the system shows Armbian 23.02. Am I missing something to get 23.5?

I did a fresh install of armbian jammy 23.5 cli on my orangepi 5 (I previously used 22.11 and 23.02), and I cannot reboot. "sudo reboot" just hangs the system. Not really a big deal, just somewhat annoying, because previous versions runs fine. Anybody else experiencing the same problem? "armbianmonitor -U" output is attached. armbianu.txt

booted opi5 via nvme one day and the boot screen mentions about btrfs partition missing even tho it was using ext4 partition. booted via sdcard and the root partition is entirely missing on the nvme. the boot partition is still there and working. not sure if relevant but the previous time i shut the opi5 down, i forgot to unplug it and it was plugged in for about an hour after shutdown with the red led and fan on. the nvme is kingspec which while cheap doesnt seem to have that many bad reports online that i can find (the boot partition was fine so i suspect kingspec isnt at fault). the power adapter is a 25w phone charger w/ pd/qs; it hasnt exhibited any weird behavior (l…

Hello Armbian forum, I need to have a GPIO interrupt on Orange PI5. I have successfully installed WiringOP and I am using it with C code. The problem is that the interrupt is not working, and I am receiving the following error. How can I proceed? Does anyone know how to enable the WiringOP interrupt on the GPIO PIN? Code C : #define AUX 13 wiringPiISR(AUX, INT_EDGE_FALLING, &MyFunction); Error: wiringPiISR: unable to open /sys/class/gpio/gpio92/value: No such file or directory PS. I have just successfully installed this version: Armbian 23.02 Jammy Gnome

root@orangepi5:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 223.6G 0 disk ├─sda1 8:1 0 256M 0 part /boot └─sda2 8:2 0 221.1G 0 part /var/log.hdd / mtdblock0 31:0 0 16M 0 disk mmcblk1 179:0 0 29.8G 0 disk ├─mmcblk1p1 179:1 0 256M 0 part └─mmcblk1p2 179:2 0 29.2G 0 part zram0 254:0 0 7.7G 0 disk [SWAP] zram1 254:1 0 50M 0 disk /var/log root@orangepi5:~# cat /boot/armbianEnv.txt verbosity=1 bootlogo=false overlay_prefix=rockchip-rk3588 overlays=orangepi-5-sata fdtfile=rockchip/rk3588s-orangepi-5.dtb r…

Hi, Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110 works well with my OPI5. I can ssh to and play with it from my Debian desktop. I don't have HDMI monitor so I want to try serial port. i'm using USB-TTL cable to connect OPI5 to my Debian box. Then in Debian bash I use this command to connect to the port screen /dev/ttyUSB0 Then power on the OPI5. The output is garbled: If i change it to cs7 (screen /dev/ttyUSB0 cs7), the output is still something I cannot understand: The stty command and output: $ sudo stty --file=/dev/ttyUSB0 --all speed 9600 baud; rows 0; columns 0; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; e…

For some odd unknown reason. I can not get the following installed and running. (using official os for Opi5) 1- A virtual machine running on armbian. 2- Dolphin emu 3- Waydroid Thx, vandyman

After updating my Orange Pi 5 I no longer can use the "opi5-i2c5-m3" overlay in /boot/armbianEnv.txt to activate and use i2c. Seems the file (or any ohter "opi5-i2c*") is gone from /boot/dtb folder. #uname -a Linux 5.10.110-rockchip-rk3588 #1 SMP Sun Apr 2 14:30:48 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux Is there a new or different procedure to activate i2c? Do I need to install a separate package for it? Or build the entire OS? Anyone else having the same issue? It does detect some i2c devices(0,10,2,6,7,9), but they don't seem to be related to the GPIO headers, prevoiusly I could also use (1,3,5). # ls -l /dev/i2c- i2c-0 i…

with clean install of armbian plus those 4 lines to install hardware acceleration glmark2-es2 gives score of about 800-900, about less then 25% of performance opi5 is capable. is it possible to raise that a bit, not all the way but just a bit more without instaling gnome or wayland, just to keep armbian as clean as its possible. as it is, its stable but barely(they do run) able to run 4k youtube oe 4k mkv, as soon as there is gnome and wayland it starts to crash, joshua rieks version, monka, armbian with all the drivers, any i tried it would crash eventualy.

I am after compiling a module for a wireless card. I got plenty of errors, thus decided to go to the basis and test the creation of a "hello" module. I am using the image: Armbian_22.11.4_Orangepi5_jammy_legacy_5.10.110_xfce_desktop.img vi hello.c ------------------------------------------------- #include <linux/init.h> #include <linux/module.h> static int hello_init(void) { printk("Hello Orange Pi -- init\n"); return 0; } static void hello_exit(void) { printk("Hello Orange Pi -- exit\n"); return; } module_init(hello_init); module_exit(hello_exit); MODULE_LICENSE("GPL"); ------------------------------…

Hi all, I'm trying to debug a sporadic problem with my Orange Pi 5 (16GB) which I'm unable to reproduce. I'm hoping maybe someone else experienced a similar issue or at least has any pointers on how to debug it further. The problem: At random times of the day, the board just appears to freeze up. All communications stop. Board is powered on, with red LED on and green LED off. I have to manually unplug the device to reset it. Within the last 2 weeks, this happened 3 times already. Each time, the last log appears to be a journalctl flush (example: https://pastebin.com/dDm5Xtis - the board froze at midnight, no more logs until …

Hello, I'm planning on running a k3s cluster with Rook storage with a few of the Orange Pi 5 that I got. A prerequisite for rook however is RBD module. I've been able to recompile the kernel including RBD support, however I've been unable to get the device to boot from the new kernel. Rebooting after kernel has been built and installed still reports Linux 5.10.110-rockchip-rk3588. Any help would be appreciated. I've since wiped the boxes clean and have a fresh install booting from SSD with the OS installed on the NVMe attached so I will be able to provide any information required. Thanks!

``` May 21 21:53:26 rpc.idmapd[21345]: main: fcntl(/run/rpc_pipefs/nfs): Invalid argument May 21 21:53:26 systemd[1]: nfs-idmapd.service: Control process exited, code=exited, status=1/FAILURE ``` The rpc.idmapd version in Debian is still ancient (as with many things in debian) and still requires dnotify but the armbian kernel for the orange pi 5 build ``` $ grep -i dnotify /boot/config-5.10.110-rockchip-rk3588 # CONFIG_DNOTIFY is not set ``` It looks like bookworm will likely fix this when it's out, so maybe the right thing to do is simply move to bookworm asap but this does prevent the ability to fully support nfsv4 with…

Hi. Great work with Armbian. Any good advice setting up Wayland and pipewire (for OBS studio) on the Orange pi 5 (23.02 jammy gnome)? I did manage to install both pipewire+pipewire-media-session+pipewire-pulse+related qt5 Wayland package and setting up QT_QPA_PLATFORM=wayland environment variable. But no luck.

For a fresh install of the latest desktop version for OrangePi5 I cannot get the system to run from NVME which is a Samsung 960 Pro. It gets stuck on the spinner at boot for the first-time boot after NVME using SD - NVME in armbian-installer. Any suggestions...

404 when trying to download SHA on this link:

Hello, I am running Armbian 23.05 "minimal" (with the provided kernel 5.10.110) on my OrangePI 5 4GB. Upgraded all packets to latest. When trying to run GeekBench 5.5.1 ARM Preview, it reboots when approaching the end of multicore tests, with "performance" governor and default speed range (0.4 - 2.4 GHz for A76). Same goes if I drop the max clock speed to 2.2 for A76. After dropping to 2.0 GHz max, it runs fine; but this hurts performances quite a bit. I tried various power sources, including a bench PSU which can reliably supply up to 30A (but I only see a few spikes over 2A). The board has a large heatsink installed wit…

My microphone is not working on armbian jammy gnome Device : Opi 5 16GB I tried to use command arecord -l I showed 1 sound card Named rockchip or something like it with similar name.

Expected Behavior: I am able to enter sleep mode, either graphically or using systemctl suspend, and then wake from sleep mode by typing on the keyboard or pressing the power button Current Behavior: The system appears to enter sleep fine, but once in sleep pressing the power button or pressing buttons on the keyboard seems to do nothing (pressing keys on my keyboard causes it to light up, however my mouse does not light up). The display remains blank and the green led does not blink. I have to do a forced shutdown by holding the power button or unplugging the power supply. Note: the behavior is the same no matter if I suspend from a desktop sessio…

I am trying to play some dolby vision movies in Armbian (Orange pi 5) but the colours are not accurate. Do you know if it is possible to play DV movies and how? Thankd

Expected behavior: rastered content is smooth like so: Observed behavior: rasterization is very pixelated: Workaround: go to about:flags and change #enable-gpu-rasterization to disabled, however this makes sites such as geogebra.org/calculator run very slow.

I have no sound over hdmi with my Orange pi 5. I have tried installing alsamixer and alsatools but this reports no settings to adjust. I have looked in files-boot-config for the sound settings and line 5242 says HDMI analogue is not set. I tried altering that to =y but I am not allowed to alter anything here and save it, ( oh how linux loves denying you permission). Does anyone know how to apply some common sense to this, why do the Armbian developers think it is a good idea not to have sound over HDMI, there is no option at al to select this in sound settings. Yours extremely miffed.

The OPI5 has an onboard RTC. On the back of the board near the RTC chip there are two pcb "test points". One says RTC1, the other says GRD1, I would assume a CR2032 could be connected to those points to maintain RTC function. I don't dare do anything till I get a solid answer. Can anyone give me any feedback as to options.

Orange Pi 5 is a new board using RK3588S. I think it would be really nice to support it http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5.html

Have anyone experience with 3rd party module connection with SPI to Opi5? I'm running Linux orangepi5 5.10.110-rockchip-rk3588 #23.02.2 SMP. I add spidev device using armbian-config (opi-spi4-m0-cs1-spidev) verbosity=1 bootlogo=false overlay_prefix=rockchip-rk3588 fdtfile=rockchip/rk3588s-orangepi-5.dtb rootdev=UUID=6fc3824e-c6c2-4781-8807-20e5a4bfc432 rootfstype=ext4 overlays=opi5-spi4-m0-cs1-spidev Two devices appears - crwxrw-rw- 1 root root 153, 0 Apr 17 10:55 /dev/spidev4.0 crwxrw-rw- 1 root root 153, 1 Apr 17 10:55 /dev/spidev4.1 Internal loopback test with spidev_test works w/o problem if I put wire MOSI <-> MISO. …

My orange pi 5 armbian Os isn’t displaying hdmi output to my monitor. However, it works on my flat screen tv, any reason why this might be ?

In the most recent builds, the kernel logs have been flood with Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x8…

Hi all Armbian fans, As of today, I checked officially platinum supported Armbian version for Orange Pi 5. I was amazed how low performing is armbian image. I was using latest armbian with HW install procedure at: https://redirect.armbian.com/orangepi5/Jammy_legacy_gnome , and Ubuntu from https://github.com/Joshua-Riek/ubuntu-orange-pi5/releases/download/v1.11/ubuntu-22.04-preinstalled-desktop-arm64-orange-pi5.img.xz Both glxinfo -B says: Accelerated : yes Armbian glmark2 Score: 705 Ubuntu glmark2 Score: 1285 Difference is HUGE When we could expect any "normal" Mali…

Orange PI 5 doesn't boot after firmware update using ARMBIAN beta tool. There isn't so much documentation, as this board is new. How to recover the firmware?

I have issues enabling hardware acceleration on Debian CLI, anyone had same problem? can someone give a tutorial?

Hey, I'm experiencing graphics failures, accelerated decoding problems, flickering window decorations and shell hangups in Plasma. All events are associated with syslog entries: dma-pl330 fea30000.dma-controller: pl330_submit_req:1738 Try increasing mcbufsz (258/256) dma-pl330 fea30000.dma-controller: fill_queue:2264 Bad Desc(2) I've attached the whole system log in case someone is interested. Running Armbian 23.02.2 Jammy Linux orange 5.10.110-rockchip-rk3588 #23.02.2 SMP Fri Feb 17 23:59:20 UTC 2023 aarch64 Panfrost-mesa updated to HEAD. A very similar problem occurs with Orange Pi 5 Debian ready distro images, but …

i was not able to build RTL8821CU driver, keep getting the following error : /usr/bin/aarch64-linux-gnu-ld: drivers/net/wireless/rtl8811cu/core/crypto/aes-internal-enc.o: in function `aes_encrypt': aes-internal-enc.c:(.text+0x74): multiple definition of `aes_encrypt'; lib/crypto/aes.o:(.text+0x7c4): first defined here make: *** [Makefile:1286: vmlinux] Error 1 There seems to be a duplicate implementation of aes_encrypt function between rtl8811cu source code and linux_rockchip64 kernel source code which blocking the armbian build. any suggestion how to fix this ?

Hi, I have the board connected by HDMI to a TV but when I start I have no sound, I have to go to the speaker icon, configuration and the option is always selected "Speakers - internal audio" but if I want to have sound I have to choose the output option "Analogic ouput- internal audio" and if I restart I have to do the process again. According to the fine adjustment guide of ARMBIAN I must execute the command pacmd list-sinks | less And should be marked with * the selected card but none appears with that symbol. I attach the terminal output after selecting the right output on the desktop to have sound to see if someone is so kind to help me solve my problem. Thanks a…

I'm looking to try an OPi5 for GPGPU. After seeing trunk recently added the patches needed to use the "gofaster" option for panfork, and having seen reports of glmark2 scores of 4000 and 5000 while never coming close to that myself, I decided to pull together the various bits of info out there and just try all of the options. A number of things done below are often described vaguely -- hopefully it's helpful here to lay out a concrete set of steps to follow and what to expect. There are two options for accelerated video: panfork and ARM's closed source "blob" driver. With either option, it sounds like you should switch from X11 to Wayland. If you are looking a…

I have tried to activate CANBUS using "armbian-config", but it does not appear in /dev/, neither with i2c

I'm really struggling to get chromium to work correctly with hardware acceleration. 1) I have custom kernel image from master branch last week. Which maybe could cause some issues? 2) I added the two repos (panfork and mesa) sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia 3) I've ran all the updates 4) I installed ubuntu desktop to enable Wayland which is working nicely 5) I've added the HDMI audio output 6) My default chromium configuration does already have the egl enabled. When I start Chromium, I get the following errors 39610:39643:0125/091804.694008:ERR…

I thought it would be easy, but I am now turning in circles, so I am asking here. I have a working system booting on NVME (when no SD card inserted), with two partitions nvme0p1 (256Mb) and nvmeop2 (40Gb) I would like to clone my working system on a SD card. How shall I proceed? I am not asking details instruction, only the rough path I should follow (e.g. dd partitions, tune2fs ......). PS: I thought it would be easy, but whatever I do, the system keep taking /boot on the nvmeop1, so I really struggle to boot on the /boot of the SD card

While I was waiting for my OPI5 to arrive, I searched for which OS to install, in this search I found Armbian. ----------------------------------------------------------------------------------------------------- Armbian 23.02 Jammy "CLI" https://redirect.armbian.com/orangepi5/Jammy_legacy Size: 499M, Release date: Feb 27, 2023 ----------------------------------------------------------------------------------------------------- Armbian Bullseye "CLI" https://redirect.armbian.com/region/EU/orangepi5/Bullseye_legacy Size: 427M, Release date: Feb 27, 2023 ---------------------------------------------------------------------------------…

Hello!! I got Dolphin running under Armbian and it seems its mainly GPU bound for the games that Iv'e tested. I am aware that the Panfrost drivers are not optimal but I thought I'd like to try and squeeze a few extra fps out of this setup by overclocking the GPU if that's possible. Is it? And does anyone know how I can do that? Cheers!

I'm struggling to get my Orange Pi 5 to boot to NVMe with Armbian 23.02 Bullseye CLI. With armbian-install I picked: 4 Boot from MTD Flash - system on SATA, USB or NVMe then install to /dev/nvme0n1p1, followed by updating the bootloader on mtdbblock0, and then powering off. When I remove the SD drive, and reboot. The console remains blank. When I insert the SD drive, and reboot again, the system comes up, and I can mount /dev/nvme0n1p1: $ df -h Filesystem Size Used Avail Use% Mounted on udev 7.7G 0 7.7G 0% /dev tmpfs 1.6G 9.6M 1.6G 1% /run /dev/mmcblk1p2 30G 2.0G 27G 7% / tmpfs …

What do I need to do to fix this error? Here is some information: root@orangepi5 ~# lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 22.04.2 LTS Release: 22.04 Codename: jammy root@orangepi5 ~# root@orangepi5 ~# uname -a Linux orangepi5 5.10.110-rockchip-rk3588 #23.02.2 SMP Fri Feb 17 23:59:20 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux root@orangepi5 ~# root@orangepi5 ~# apt install -y bpfcc-tools libbpfcc-dev python3-bpfcc libbpfcc Reading package lists... Done Building dependency tree... Done Reading state information... Done The following additional packages will be installed: ieee-data libclang-cpp11 libllvm11 python3-n…

I decided to try the new Armbian 23.02 Jammy Gnome build and after booting with my SD card, the process gets to a point where it presents a prompt orangepi5 login: and whatever I attempt to enter returns as an incorrect login. I can't find any specific documentation which indicates the default login credentials for this build.

Has anyone run a comparison benchmark of Armbian vs. the Orange pi versions of Debian and Ubuntu? ...Curious to see the results of optimizations.

Hello all! In Orange Pi OS latest image all works well EXCEPT it keeps launching apps in a stupid bordered window that has a huge obnoxious bar at the top with 2 absolutely useless buttons, a window to full screen option and the X button How do I hide this stupid thing? It's blocking the whole top of my screen and cutting off part of my TiviMate Pic here https://imgur.com/a/8uo8WrM

Hello!! I just got my Orange Pi 5 the other day and am trying to 'port' a program I've been working on for RPi4b over to this new board. The program is using ffmpeg to decode h264 and hevc video streams. My main question is how do I need to configure the ffmpeg codex context and formats to make use of (ideally zero copy) HW accelerated video decode on Orange Pi 5? For the raspberry code I was using these: avcodec_find_decoder_by_name("hevc"); and avcodec_find_decoder_by_name("h264_v4l2m2m"); together with codec_context->pix_fmt = AV_PIX_FMT_DRM_PRIME; // for zero copy video path But this does not work when compil…

In the original PR for Orange PI 5 I recall someone mentioned that the Jammy had somekind of glitch with USB on the OPI5 but is that still the case? From the threads here, it looks like the distribution has many patches and fixes. Is Bullseye the recommended distribution?

I was running on Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop. For the most part, it worked but the mouse cursor would randomly disappear while remaining functional but invisible. I tried to upgrade using apt-get update and apt-get full-upgrade and after a reboot, it now just displays a flashing underscore. I can SSH into the OS so it's partially functional. Shows as Armbian 23.02.2 Jammy with Linux 5.10.110-rockchip-rk3588 Contents of boot.log: ------------ Mon Feb 27 07:24:15 PST 2023 ------------ done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running…

Howdy, I am in desperate need of help getting this dang usb wifi dongle working on my orange pi 5. I am new to sbc and fiarly new to linux. I have tried multiple github drivers with freash OS installs, all to no avail. Time spent trying to get it to work is reaching close 20 hours, across multiple forums, github searches, videos, linux how to site, and armbian site itself. I'm either missing something or an idiot cause i can't figure out this "make" or "dkms" command stuff out for compiling the driver and installing it. My last resort is asking for y'all for help before i feed this thing to my dog... "joke". My most recent attempt is from the git h…

Hi all, recently I installed the Mali GPU Drivers from the instructions on the official Armbian website. I have Armbian 23.02.2 Jammy installed, with KDE Plasma desktop. I found two problems: 1. The mouse flickers when I move it. This happens on both XFCE and Plasma (X11) 2. Every once in a while, the Plasma panels freeze and I have to reboot my OPI to get it to work. This also happens if I right-click on it and press "Enter Edit Mode". If I don't do that, it freezes randomly (afaik). This affects both the panels and the background (panels don't update, can't interact, cannot right-click). Does anyone know of any solutions to this? Thanks!

Hi, Im pretty new to linux in general mostly used windows before. Is there a way to get waydroid work on armbian? I installed it but waydroid sais that the binder kernels are missing (1). When I follow the instruction to install the kernel modules using dkms I also get a failure (2). (1) ERROR: Binder node "binder" for waydroid not found (2) Error! Bad return status for module build on kernel: linux-headers-5.10.110-rockchip-rk3588 Anyone can help me with this? Thanks in advance!

I am waiting on my opi5 but was already investigating how to run Roblox (an x86 32 bit Windows game) on it. Grapejuice + box86 + wine could do the trick and saw this interesting script: https://github.com/NicoD-SBC/armbian-gaming Will this be working for opi5 too or is it specific to rk3399 (saw that in some compiler flags)? Anybody experience or an updated installer script? Related info: This YouTube channel covers examples of running games on rk3588 (rock5b) making me believe performance could be quite good: https://youtube.com/@TheByteman

Here is a video of my Orange Pi 5 setup. Hopefully someone finds it helpful!

Tried 5 diferrent microSD cards, 3 card readers, multiple redownloads on Mac and Windows. Diferrent power supplies, including 100W charger and 52pi EP-0136 direct 5v supply. No green LED, no LAN communication, no HDMI output. Everything i get is in log (via UART) Please help... i've got no more ideas. DDR Version V1.08 20220617 LPDDR4X, 2112MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB Manufacturer ID:0x1 Samsung CH0 RX Vref:32.7%, TX Vref:1…

Hi all, I’m new to this whole SBC thing, and I recently got an Orange Pi 5. I first installed the official OS (Ubuntu), where I needed to do into orangepi-config and go into System > Hardware > wifi-ap6275p and enable that to use the official M.2 WiFi dongle. However, I don’t see this option on Armbian. Does it not support it?

Problem 1 i just installed Operating system, and then used coding command sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia sudo apt update sudo apt dist-upgrade sudo apt install mali-g610-firmware rockchip-multimedia-config to activate 3d accelerator. but it failed and an error appeared Errors were encountered while processing: /var/cache/apt/archives/mali-g610-firmware_1.0.0-1_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) https://ibb.co/0BhLJzm Problem 2 operating system can't mount exfat partition format so I used the following command sud…

I have setup the hardware acceleration as explained in the posts, but within Kodi, every now and then I can see the image with "pixelising", and looking in the syslog when this just happened, I can read: Feb 15 16:54:17 orangepi5 kernel: [ 1267.908544] mpp_rkvdec2 fdc48100.rkvdec-core: reset done Feb 15 16:54:17 orangepi5 kernel: [ 1267.908549] mpp_rkvdec2 fdc38100.rkvdec-core: resetting... Feb 15 16:54:17 orangepi5 kernel: [ 1267.908670] mpp_rkvdec2 fdc38100.rkvdec-core: reset done Feb 15 16:54:17 orangepi5 kernel: [ 1268.316705] mpp_rkvdec2 fdc48100.rkvdec-core: resetting... Feb 15 16:54:17 orangepi5 kernel: [ 1268.316855] mpp_rkvdec2 fdc48100.rkvdec-core: …

Hi, I've trouble getting 3840x2160 resolution to work. When I try to switch to that resolution the monitor says resolution is 3848x2160 and display is all garbled. 2560x1440 works fine. Also, If I try to login to Gnome (Wayland) I get blank screen and I'm back at the login screen. X11 lets me login to the system. uname -a: Linux lindon 5.10.110-rockchip-rk3588 #trunk.0184 SMP Fri Jan 20 18:24:04 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux I've fetched the latest updates (apt update && apt upgrade) and I've just ran firmware update using armbian-config. Edit: display is connected via usb-c - - > displayport cable.

I want to install the usb wifi/bluetooth card drivers but I keep getting an error during compilation. What to do? below code: DKMS make.log for rtl8812au-5.13.6 for kernel 5.10.110-rockchip-rk3588 (aarch64) Tue Jan 10 08:48:19 PM CET 2023 make ARCH=arm64 CROSS_COMPILE= -C /lib/modules/5.10.110-rockchip-rk3588/build M=/var/lib/dkms/rtl8812au/5.13.6/build modules make[1]: Entering directory '/usr/src/linux-headers-5.10.110-rockchip-rk3588' CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_cmd.o CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_security.o CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_debug.o CC [M] /var/lib/dkms/rtl8812au/5.1…

I just installed the most recent nightly image - this one looks like a major update but it broke armbian on my opi 5 1. I had to re-install the mali firmware to get x11/wayland to start - not sure why the update deleted the file 2. I had to re-install the mali-g610-firmware rockchip-multimedia-config packages 3. VLC cannot start the h264 decoder anymore [0000005583627590] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface. Warning: Ignoring XDG_SESSION_TYPE=wayland on Gnome. Use QT_QPA_PLATFORM=wayland to run on Wayland anyway. [00000055836b79e0] main playlist: playlist is empty [h264_rkmpp @ 0x7f4cc37630] Failed…

I've been trying to implement traffic shaping using tc. But it seems that ingress is not working. I am running Armbian Minimal Server on Orange Pi 5. Running this command: tc qdisc add dev eth0 ingress Will throw an error: Error: Specified qdisc kind is unknown. This has been working for orange pi pc/one armbian. Does the ingress module missing from this build? Can anyone point me to the right direction. Thanks.

So recently I flashed Orange Pi OS to SD card, booted from there, updated system, firmware and flashed bootloader to SPI flash. I already had an external HDD with Armbian flashed, and tried to boot from there, but no luck. Afterwards, I tried to boot Armbian from SD card, but I can't boot any system that is not Orange Pi OS (and especifically, it needs to be from SD card, can't also boot from USB even in OPi OS). Tried with different SD cards and USB devices, no luck I believe I need to erase SPI flash in order to boot from SD again, but, how can I do it? Used latest OrangePi OS and Armbian Jammy CLI from 23/01 (stable release)

I finally found an official source code on the download page of OrangePI that has a version of wiring pi with support for the Orange PI 5 - unfortunately that code is not on the github of orangepi yet. What would be the best way to get this code and the gpio tool into armbian? Build a PPA and package for that one? I don't mind forking their repo and adding the mods but I'm not familiar with generating debian packages.

After upgrading today with "apt update && apt upgrade" I was no longer able to watch videos. mpv player would Segfault, also tried vlc - not working either. Gnome desktop with wayland itself works, only video playback seems to be affected. After rolling back the following packages in liujianfeng1994 repo it started to work again: librockchip-mpp1:arm64 OLD: 1.5.0-1+git221020.d63affb~jammy NEW, causes segfault: 1.5.0-1+git230210.c145c84~jammy The repository no longer has the old version, but I managed to get it back to 1.5.0-1+git221020.d63affb~jammy like this #Find the deb file from cache find /var/cache/apt -name '*librockc…

Only sharing what I managed to make working on the Orange Pi5: a Tvheadend server with satellite cards TBS 5527 and TBS 5520se. The rough path I followed: - recompiled the kernel in order to have "Linux tv" as a module (CCONFIG_DVB_CORE=m). This will be replaced by the tbs driver in next steps. - installed TVheadend from the armbian-config - compiled tbs drivers by following standards instructions....but: - had to add a CFGLAGS += -w to avoid some warning stopping the build (Makefile in the v4l directory) - had to disable the creation of the mc.ko (MEDIA_CONTROL) to avoid conflict with kernel built-in module (n…

Just interested if anyway has being able to set this up in Armbian yet? I had a brief look this morning but couldn't get it to work.

Processing triggers for initramfs-tools (0.140ubuntu13.1) ... ln: failed to create hard link '/boot/initrd.img-5.10.110-rockchip-rk3588.dpkg-bak' => '/boot/initrd.img-5.10.110-rockchip-rk3588': Operation not permitted update-initramfs: Generating /boot/initrd.img-5.10.110-rockchip-rk3588 update-initramfs: Converting to u-boot format I am getting this error every time I do an apt upgarde. I am running on a 256Gb NVME drive and booting off of it with no problems. So does this error mean it's not actually updating /boot/initrd.img-5.10.110-rockchip-rk3588 ? The third line there makes me think that it just fails with the hard link and then generates the…

Hello, I have a problem with mounting a USB HD via fstab. If I enter the HD in the fstab, the system hangs when booting. The problem, USB is not activated yet and will be loaded later. If I remove the HD from fstab, it is automatically mounted under /run/media/USER. However, this must not be mounted under a user, but should be mounted as root. What can I do. Thanks very much

I am trying to build the kernel with the standards scripts, but directly on my orange pi 5. The build is stopping at some point because of a Warning issued by the compiler (this is the default behaviour for the compiler who does not tolerate any warning by default). (Some functions in the C code are depreciated, thus a warning is issue) How can I set the CFLAGS so that the kernel build takes it into account during compilation? Thanks.

I have an Orange Pi 5 (16GB RAM) running Armbian Jammy with the latest updates installed. I am booting from NVMe and when it boots successfully it runs flawlessly without issue. The problem occurs when I reboot -- the majority of the time it does not boot up successfully. Sometimes when it boots I only see the red light (and no green light), and other times I will see the green light flash like normal, yet the external hard drive does not spin up or mount properly. This results in me needing to power down the Orange Pi 5 and try again. Eventually it will boot up successfully (along with the external HDD) and then everything is good; that is, until the next time I have to …

I am trying to compile the Kernel on my PC with the Ubuntu recommended version. I get the error below: arch/arm/dts/rk3128-evb.dtb: Warning (avoid_default_addr_size): Relying on default #address-cells value for /syscon@20008000/usb2-phy@17c arch/arm/dts/rk3128-evb.dtb: Warning (avoid_default_addr_size): Relying on default #size-cells value for /syscon@20008000/usb2-phy@17c FATAL ERROR: Couldn't open "./u-boot.dtb": No such file or directory ./tools/mkimage: Can't read u-boot.itb.tmp: Invalid argument make: *** [Makefile:1053: u-boot.itb] Error 255 Any idea what this could be? It is the first time I am running ./.compile.sh potential…

I'm trying to setup LIRC on my OPI5 but I can't find any details on how that would be possible. I checked the kernel configuration and I cannot see any references to LIRC either. The module list has nothing obvious - is this feature completely disabled? Any suggested alternatives?

Hello All, Do you also have this kind of messages in syslog ? [ 1601.687044] ------------[ cut here ]------------ [ 1601.687070] WARNING: CPU: 2 PID: 112 at drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2986 vop2_crtc_load_lut+0x54/0x310 [ 1601.687075] Modules linked in: bnep zstd joydev sch_fq_codel fuse ip_tables ipv6 r8152 panfrost gpu_sched [ 1601.687114] CPU: 2 PID: 112 Comm: kworker/u16:1 Tainted: G W 5.10.110-rockchip-rk3588 #trunk.0184 [ 1601.687117] Hardware name: Orange Pi 5 (DT) [ 1601.687127] Workqueue: events_unbound commit_work [ 1601.687134] pstate: 40c00009 (nZcv daif +PAN +UAO -TCO BTYPE=--) [ 1601.68713…

There is no Orange Pi 5 results yet, but we can see already results of RK3588S. https://github.com/ThomasKaiser/sbc-bench/blob/master/results/Sorted-Results.md

Hello, finally I have time to play with my OPI5, first thing I tried is to install on USB-C, but the port doesn't seem to work. Then I tried to install using USB3 port, on a ssd drive. The armbian-install utility seems to do the job and after installing the bootloader on mtdblock0 I powered off. At reboot everything is like before: if I remove the sd card the systen won't boot. If I boot with the sd card inserted the root partition is on /dev/mmcblk0p2 First thing that came into my mind is to mount SPI and check if bootloader is ok, but I'm unable to mount it: ~# mount /dev/mtdblock0 /mnt/spi mount: /mnt/spi: wrong fs type, bad optio…

I want to install Armbian on Nvme SSD. How do I install on SSD?

I know this driver should be part of the recent kernel releases (and definitely avail for 5.10) but I am not sure how/why/where this driver would be in the armbian release. I also did install the firmware files but I don't see the module in the /usr/lib/module section. Any suggestions to build or enable this driver? Thanks

Hi there, Just got Orange Pi 5 8GB and have no idea where to begin. I have a microSD card available, but no writer. I had the idea to boot from USB thumbstick and then write the SD card using the port on the Orange Pi 5, then I can boot from SD card. Is this possible? What image and method do I need to follow in order to boot from a simple 32GB USB Sandisk thumbstick? Thank you!

I saw that you now have a stable release of armbian for opi5. I installed Armbian 23.02.0-trunk.0112 Bullseye a week ago. Now I'm wondering if it is possible to switch back to the stable version without reinstalling the system. The OPI is now running in production and I have several containers running on it. This is what I tried -> armbian-config -> system -> nightly after that back to stable -> armbian-config -> system -> stable ->armbian-config -> system -> other -> linux-image-legacy-rockchip-rk3588=22.11.4 But after login I always see: Welcome to Armbian 23.02.0-trun…

I did a bit of reading - to prevent ubuntu packages to update the rockchip optimized packages, you need to pin the packages. There is a simple way to do that. 1. Create a file called rockchip-multimedia-ppu in /etc/apt/preferences.d with Package: * Pin: release o=LP-PPA-liujianfeng1994-rockchip-multimedia Pin-Priority: 600 2. Create a file called panfork-mesa-ppu in /etc/apt/preferences.d with Package: * Pin: release o=LP-PPA-liujianfeng1994-liujianfeng1994-panfork-mesa Pin-Priority: 600 You can verify that the apt configuration is working correctly with sudo apt policy chromium-browser which should return chrom…

Has anyone tried GPIO access on the latest armbian? I noticed that the custom wiringPi https://github.com/orangepi-xunlong/wiringOP.git doesn't compile on armbian. It is missing GPIO constants.

How do I get DVB drivers to work. I have a Technotrend TT Connect S2-3650-CI. All DVB drivers are missing

I found this amazing page https://linux-sunxi.org/Sunxi-Cedrus#VLC that explains alot on VLC and hardware accelleration but I cannot clearly figure out if my playback is using hardware acceleration. I did follow all the steps to optimize chromium with the ppu sources - chromium doesn't work well yet for me - so not sure if that install worked as expected. My playback of h264 in VLC is super smooth but I have around 20-35% cpu usage (1080p videos) - I know h264 is more demanding than AV1 but someone reported AV1 with 15% CPU usage and 4k. Is there anything I can do to make sure the hardware acceleration is working (aka the VA-API is used)?

I am attempting to install the file Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop.img from https://www.armbian.com/orangepi-5/ but the installation hangs at the point where the root password should be entered. The same happens with the file Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_minimal.img. If i use the file Armbian_22.11.3_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop.img from the Github archive the installation completes. I have tried to raise a bug but the only solution for not booting are hardware and the installation has not progressed far enough to enter any commands. Any assistance welcomed.

Not sure if the rolling release includes the UART dtb yet, but when I build my own image (jammy xfce kernel 5.10.110) I don't have the UART dtbs in /boot/dtb/rockchip/overlay/ . As a result, I couldn't add uart0-m2 to /boot/armbianEnv.txt and get /dev/ttyS0 when I was following the official user manual to enable UART. After some researching I managed to solve this by copying the dtb file from orange pi's official ubuntu image to /boot/overlay-user and enable UART with user_overlays=rk3588-uart0-m2 in armbianEnv.txt . Rebooted and it works. However, I suppose it would be better to include the dts files in kernel patches? I'm posting this because I don't know what…

My Orange Pi 5 with latest debian does not reboot. I use it faceless (without local screen) via RDP (LAN) from Windows, works fine. But I cannot reboot. Neither via RDP nor via SSH. The green LED stops blinking, the red LED continues. But no LAN access. Must do hard reset via button or power off/on. Any ideas?

The armbian can't support the third usb bus with pi5.But the official system debian runs normal to support the third usb bus.How to solve the problem?

I have seen the uefi port for Rock 5B, which uses rk3588. seed this the opi5 use rk3588s which may lack some IOs, so I think maybe it can work on opi5 without modification. (actually i don't know how to modify to fit for it, need to learn) here i show you the result, I burn the uefi image (complied from balbes150's repo: https://github.com/150balbes/edk2_uefi ) to a tf card, then burn the image from balbes150's post to a usb portable ssd. then i change the dtb. The efi and grub can boot form tf card and then load the image from my usb ssd. successfully enter the Armbian and seems no big issues. But this can only work on the 2 type-A usb3.0, i try on usb2.…

Stable, weekly and CI builds https://www.armbian.com/orangepi-5/