Rockchip

Hi I need help, I have used in the past the Banana PI M1 card for many years with a SATA Port Multiplier. To enable PMP support for this card, you had to edit: nano /boot/boot.cmd Go to line that starts with: setenv bootargs and add at the bottom of the row: ahci_sunxi.enable_pmp=1 recompile with: mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr Restart Almbian and the SATA Port Multiplier was activated. I now own a RockPro64 with Armbian and a 6-port PCIE sata card. Should buy a card with 8-10 ports to add hdd that I will need to make backups. …

• 0

  Reputation Points

• 1 reply
• 3.3k views
• 1 follower

DBSD

August 2, 20206 yr

I am considering to buy a RK3399 dev board and use USB 3.0 peripheral mode to transfer data to/from another host PC. It may be used as USB CDC/Eth or RNDIS device, or a MTP device. We hope the transfer rate could be well over 1Gbps, the higher, the better. So has anybody ever benchmarked RK3399 USB in peripheral mode? Such as the highest iperf transfer rate in CDC/Eth or RNDIS mode?

• 1

  Reputation Points

• 12 replies
• 12.3k views

haajee

August 1, 20206 yr

Hello i hope you all have a nice day At first i need to thank you for all the work you done. I'm runnig my ROCKPro64 no for a while now Today i wanted to try wifi and bt but it looks we dont have any drivers for the module AMPAK AP6256 Combo Module and made specifically for the ROCKPro64 Debian 10 headless 20.08.0-trunk Can someone help me to reach the goal to use my wifi ?

• 0

  Reputation Points

• 2 replies
• 4.8k views

max12m3

July 13, 20206 yr

I just started RockPro64'ing (though been using Linux for about 25 years) and bought the low profile fan with the RockPro64. Armbian (downloaded today) installed fine, sees my NVME etc. so all good. The only issue I have is that once the OS starts up the fan comes on and never stops - it seems to be running 100% all the time. It the speed meant to vary? And is it meant to turn off sometimes when not required? I'm wondering if I am I missing a config file entry for this. Thanks for any assistance and well done on the distro.

• 0

  Reputation Points

• 3 replies
• 4.3k views
• 2 followers

Indieshack

July 7, 20206 yr

Hi there, I have a very strange issue: kernel 5.4.14-rockchip64 debian_version 10.3 Armbian 20.02.0-rc1 stable cable is OK - checked eth0 in /etc/network/interfaces.d/eth0 set to dhcp ---- unfortunately the rockpro64 gave up with an hardware ram issue The unit was replaced and luckily I have an image: March 3, 2020 which was OK and fully functional. Today I threw it on the SD-Card and I do not have a NIC at all. A.m. Data drawn from the OS hwinfo issues RTL8211F irq:0 27 "eth0" lshw network:0 eth0 id9 with MAC network:1 DISABLED dummy0 ip a d…

• 0

  Reputation Points

• 6 replies
• 5k views

Wilhelm Moser

July 5, 20206 yr

Hello people, I use a Tinker Board as a low power desktop computer for browsing, office documents and general tinkering, and after all this time it got personalized enough to worry about loosing all this setup and it is a hassle to just overwrite everything every time a new image comes around. Was wondering if it is possible to use apt dist-upgrade as means to get from Bionic Desktop 5.4 to Focal Desktop 5.4 as can be done on x86 platforms without breaking everything?

• 1

  Reputation Points

• 3 replies
• 5.5k views
• 2 followers

Technicavolous

July 4, 20206 yr

I logged an issue a little while ago with Armbian running on the Tinkerboard that the screen when rotated 90 degrees couldn't draw the screen at any speed. I have been playing with a few alternatives incl going back to the original tinkeros. All have issues so I was delighted to see the FOCAL port. I am using the recommended Waveshare 7" touchscreen that you advertise on the home page as tested 3rd party hardware. Both the desktop and the server versions of Focal come up with the error Configure crtc 0 failed setting mode when I manually set the supported resolution of 1024 x 600 at 60Hz using xrandr Exactly the same settings on TinkerOS works perfectl…

• 0

  Reputation Points

• 3 replies
• 5.6k views
• 1 follower

Myy

July 2, 20206 yr

Hi all! Rockchip64 20.05.4 kernel images are missing from the PPA. There is only 20.05.3 in https://apt.armbian.com/pool/main/l/linux-5.4.45-rockchip64/ and no https://apt.armbian.com/pool/main/l/linux-5.4.46-rockchip64/ I am looking for the header package in particular to build zfs. Can you make those packages available, please? Best regards, kryps

• 0

  Reputation Points

• 2 replies
• 3.4k views

kryps

June 28, 20206 yr

Hello people, I have an Asus Tinker Board S and decided to use the Mainline Armbian for this board, love the new panfrost driver but seems it is glitching all over the place, icons in the menu disappear and reappear when mouse hovers over them, tick boxes do not show if they are ticked and only flicker when mouse is over them and applications menu keep redrawing all over when trying to use among the most prominent problems. Other operating systems work well in this matter. Anyone else is having these problems with the mainline 5.4.28 kernel build?

• 0

  Reputation Points

• 1 reply
• 3.5k views

Nikos Giannakas

June 10, 20206 yr

I have a 1 GB Renegade board and downloaded Armbian_19.11.3_Renegade_buster_current_5.3.11 image to install. Noticed it was only 510MB of RAM. Relevant extracts from serial log: U-Boot 2017.09-armbian (Nov 19 2019 - 00:09:05 +0100) Model: Firefly ROC-RK3328-CC DRAM: 510 MiB ____ _ | _ \ ___ _ __ ___ __ _ __ _ __| | ___ | |_) / _ \ '_ \ / _ \/ _` |/ _` |/ _` |/ _ \ | _ < __/ | | | __/ (_| | (_| | (_| | __/ |_| \_\___|_| |_|\___|\__, |\__,_|\__,_|\___| |___/ Welcome to Armbian Buster with Linux 5.3.11-rockchip64 System load: 0.10 0.14 0.06 Up time:…

• 1

  Reputation Points

• 11 replies
• 7.2k views
• 2 followers

Igor

June 3, 20206 yr

However, Armbian is configured to provide only spidev2.0, while TinkerOS can have spidev0.0, spidev0.1, spidev2.0 and spidev2.1 all enabled at the same time as long as you disable UART4 which shares GPIO header pins with SPI0. In the TinkerOS case, there is a config tool which edits a small and straightforward text file in /boot/ containing lines such as "intf:spi0=on" or "intf:uart4=off". The corresponding Armbian file seems to be /boot/armbianEnv.txt - possibly with overlays=... lines and DTS files. There also is a tool called armbian-add-overlay to load (at runtime?) DTS files...

• 0

  Reputation Points

• 0 replies
• 2.6k views

Bienxanh

June 2, 20206 yr

Hello, compiling Kernel 5.4.40 (setting in lib.config with KERNELBRANCH=tag:'5.4.40') under Vagrand with RT-Patch "patch-5.4.40-rt24.patch" putting in " ~/build/userpatches/kernel/rockchip64-current/ "for RockPro64 fails. ........ [ o.k. ] * [l][c] general-rt5651-add-mclk.patch [ o.k. ] * [l][c] mp8859-kbuild-makefile.patch [ o.k. ] * [c] patch-5.4.40-rt24.patch [ o.k. ] * [l][c] rk3328-add-dmc-driver.patch [ o.k. ] * [l][c] rk3328-audio-and-renegade-supplies.patch [ o.k. ] * [l][c] rk3328-clean-up-codec-gpio-SD.patch [ o.k. ] * [l][c] rk3328-fix-wrong-mmc-shift.patch [ o.k. ] * [l][c] rk3399-add-sclk-i2sout-src-clock.patch [ o.k. …

• 0

  Reputation Points

• 6 replies
• 4.8k views
• 1 follower

martinayotte

May 27, 20206 yr

I have a latest ubuntu armbian on a pinebook pro, I use an DUB-1312 gigabit to usb 3.0 for wired connection, I plug it in the usb 3 port of the pinebook but I run iperf I see the same speeds as the other usb 2 port. $ iperf3 -c 192.168.0.34 Connecting to host 192.168.0.34, port 5201 [ 5] local 192.168.0.33 port 48140 connected to 192.168.0.34 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 41.7 MBytes 350 Mbits/sec 0 298 KBytes (More thread only made results worst) While the same DUB-1312 plugged in my amd64 ubuntu computer achieve 950Mb/s easly (capped by the other testing device (an odroid-hc1)). …

• 0

  Reputation Points

• 0 replies
• 2.9k views

Jorropo

May 22, 20206 yr

Hi, hot o enable splash screen on boot fo this image: Armbian_20.02.1_Rockpro64_bionic_legacy_4.4.213_desktop.img for Rockpro64? Thanks

• 0

  Reputation Points

• 0 replies
• 2.8k views

DBSD

May 15, 20206 yr

So recently I decided to use my (quite old) tinker board, I downloaded the last armbian (desktop, 4.4.213) OS, managed to install a vncserver (x11vnc) and also to use it without a screen plugged in it. And now I would like to turn it into a urbackup server, but I got some error with mdadm, "Module md_mod not found in directory /lib/modules/4.4.213-rockchip". I tried to use this forum to find a solution (https://github.com/armbian/build), but I couldn't make it work. When i tipe ´´git clone https://github.com/armbian/build´´ it stop around 7% at resolving deltas, and it just freeze. Someone could have any idea how to solve this issue?? And i can't get my armbianmon…

• 0

  Reputation Points

• 6 replies
• 5.5k views

Werner

May 12, 20206 yr

If anyone has troubles with HDMI when using 5.x kernels, and has enough skills to recompile an armbian, give this a try : https://github.com/Miouyouyou/build And then either answer here, or in the bug report : https://github.com/armbian/build/pull/1887

• 0

  Reputation Points

• 0 replies
• 2.8k views

Myy

May 9, 20206 yr

So I have armbian installed on a tinkerboard and have had absolutely no issues with it until I bought a new Samsung 7000 series TV (2019). For some reason this TV does not recognize the signal coming from the tinkerboard. For the life of me I cannot figure out how to get this to work. I notice a few references online about being able to force a resolution but nothing related to the rockchip boards. Is there an equivalent way to force a display resolution as in this article? https://docs.armbian.com/Hardware_Allwinner/#how-to-reconfigure-video-output I'm running 4.19.21-rockchip 5.76 I've also tried kernel 5.4.28 as well an…

• 1

  Reputation Points

• 5 replies
• 4.8k views

Myy

May 9, 20206 yr

Hi, I installed "Armbian_20.02.7_Tinkerboard_buster_current_5.4.28_minimal" at my tinkerboard and, in order to enable uart 4, I had to rebuild the kernel onboard (from linux-source-current-rockchip_20.02.7_all.deb). The uart 4 came alive but the processor serial number now is missing from cpuinfo (printing 0000000000). How can I bring it up again?

• 0

  Reputation Points

• 0 replies
• 3.3k views
• 1 follower

santosmjc

April 28, 20206 yr

Topic to discuss RK3288 overlays, primarily concerning ASUS Tinker Board, the MiQi is technically EOL and has very little GPIO anyway, and TV boxes are more or less sealed. Kernel 4.19 will be the pilot for this, the discussion now that it seems to be working thanks to @martinayotte and @zador.blood.stained's feedback and examples is what to overlay. For testing/debugging I started with some ASUS overlays for RTC and 1wire. Easy ones: spidev out of the default tree but as default overlays. instead of making 1 overlay and messing with parameters, just make 2 overlays DAC's: I don't have a lot of hardware to play with, but @…

• 1

  Reputation Points

• 35 replies
• 20.9k views
• 2 followers

mtr46

April 23, 20206 yr

Hi. I installed Armbian_20.02.1_Tinkerboard_bionic_current_5.4.20_desktop on my TinkerBoard (not S) and get weird screen state (white, then growing black circle in the middle). I tried Armbian_20.02.1_Tinkerboard_bionic_legacy_4.4.213_desktop and it works very good, but I still want to test vulkan driver, so I updated only kernel to 4.19 (install linux-image-next-rockchip, linux-header-next-rockchip, linux-dtb-next-rockchip and delete 3 old packages). After reboot I got same screen. Is it known bug? Can it be related, that I'm using HDMI-to-VGA adapter? Can you help me to fix it or get usefull logs?

• 0

  Reputation Points

• 11 replies
• 6.4k views

Myy

April 19, 20206 yr

Has anybody seen this message at boot: [ 5.352826] CPU4: failed to come online [ 5.352835] CPU4: failed in unknown state : 0x0 [ 10.481328] CPU5: failed to come online [ 10.481336] CPU5: failed in unknown state : 0x0 Then, the A72 cores don't show up (unsurprisingly since these are the two cores that somehow did not come online). On top of that, the kernel throws a backtrace (related to sound if I understand correctly): ------------[ cut here ]------------ [ 13.014782] WARNING: CPU: 3 PID: 1 at kernel/irq/manage.c:1990 request_threaded_irq+0x144/0x180 [ 13.014784] Modules linked in: [ 13.014793] CPU: 3 PID: 1 Comm: swapper…

• 0

  Reputation Points

• 11 replies
• 6.4k views
• 1 follower

Myy

April 17, 20206 yr

Hi! On the Rockpro64, with the latest Amrbian dev kernel (5.4.0-rc1-rockchip64 updated on 19th of January), the sata hard drive connected to PCIe through the pine store adapter does not go to sleep anymore. It is properly set with hdparm and a udev rule, it used to work fine with the dev kernel before the 19th of January update. Now, if I issue a sleep commd (hdpram -y /dev/sda) it goes to sleep properly but not by itself after the 5 minutes inactivity I have set up. Mathias

• 1

  Reputation Points

• 5 replies
• 4.6k views
• 1 follower

Mathias

April 16, 20206 yr

I have a TinkerBoard S. In Bionic Desktop (kernel 4.4), the wireless icon menu lists two devices: wlan0 (which is the expected interface) and p2p0: I don't know this one, but it is always chosen for auto-connecting to the local wireless lan, receiving a random IP and not the one I configured on the router. I can then manually connect to the network with the wlan0 interface the IP is correct. How do I disable / remove / anyway stop that p2p0 interface to "steal" the network connection?

• 1

  Reputation Points

• 2 replies
• 9.9k views

trip

April 11, 20206 yr

I used sudo swapoff -a as suggested in this thread: but the setting isn't persisted, and upon reboot sudo swapon --summary shows a partition There's no "swap" text in my /etc/fstab I'm trying to install Kubernetes, so I need to disable swap.

• 0

  Reputation Points

• 1 reply
• 4.5k views

trip

April 10, 20206 yr

Hello, I own a Tinker Board S (bought one or two years ago) attached to a Sony Bravia KDL 22EX320 TV by HDMI, which has a native resolution of 1388x768 pixels. Bionic desktop with kernel 5.4 (got from https://dl.armbian.com/tinkerboard/Bionic_current_desktop) didn't properly recognize the TV resolution, but set it to 1920x1024. If I run xrandr --props the resolution is not listed. I'm posting because I'm almost sure that the old TinkerOS 2.0.8 (that I installed with the board) recognized the TV resolution correctly - it anyway boots to desktop without requiring interaction, so not being able to read the text at the edges of the console …

• 0

  Reputation Points

• 4 replies
• 4.2k views

trip

April 10, 20206 yr

I have Tinker Board S. I have been using both Tinker OS and Armbian for a while. Recently I upgraded to 5.4.28-rockchip. I noticed that randomly and frequently when I watch cnn.com or other media, my video would freeze. Initially I thought the firefox or chromium crashes. However, later, I realized it was the network issue. Other devices were still able to connect to the internet. When I checked the ifconfig, the network devices still showed proper connection. However, there is no way to ping any URLs. Disconnecting/reconnecting network does not fix the issue. The only fix was reboot. How can I troubleshoot this issue? I was trying to do armbianmonitor but at …

• 0

  Reputation Points

• 9 replies
• 5.1k views

Shen En Chen

April 4, 20206 yr

In order to enumerate the major issues that are *still* valid now, I'm creating a 'crash dump' thread. The idea is simple, if your RK3399 board crashed recently, you just : Write what happened during the crash; Provide the link you got from sudo armbianmonitor -u , after the crash happened; Provide the content of /var/log/kern.log (if this file is present on your system) (attach it or copy the content on pastebin and link it here). No discussion here. Feel free to create a new dedicated thread afterwards to talk about the problem you encountered. Minor issues are welcome too, if they trigger a BUG message in your logs…

• 0

  Reputation Points

• 0 replies
• 3.3k views

Myy

April 1, 20206 yr

On several RockPro64 boards I experience infrequent freezes, mostly directly on boot, but also after some longer (hours, days) uptime. I use the official power adapter and no additional hardware except a PCIe adapter for an SSD, which works flawlessly when operational. When looking at the kern.log, there are quite a few errors and warnings, but comparing to a successful boot these are all also present. So I don't think they cause the freeze directly. Currently, I recorded the freeze on the latest Armbian Bionic as release just recently. FWIW, I think the same issue also occurs on the previous Debian Stretch image (had various freezes, but have not …

• 1

  Reputation Points

• 16 replies
• 10.7k views
• 1 follower

Myy

April 1, 20206 yr

Hello togehter, i had 2 ASUS TinkerBoard S and I want to work with your software... The Software was via Etcher installed on several MC - Cards (16, 32 and 64 GB), but it still not working. The POWER - LED is red and the both LEDs on GBIC - Interface are blinking green and yellow :-( So, what kind of problems that I have here. I tried out several IMAGE from your WebSite - but no one won't to work with me :-( Best regards Matthias

• 0

  Reputation Points

• 7 replies
• 4.5k views
• 1 follower

MatthiasK

March 24, 20206 yr

Using Linux tinkerboard 4.19.69-rockchip #5.95 SMP PREEMPT Mon Sep 2 07:34:36 CEST 2019 armv7l armv7l armv7l GNU/Linux Using glxgears as a test case.. I get 60fps without the screen rotated. If I rotate the screen right or left the frame rate drops to 4fps. That's on a fresh boot with nothing else running. I tested TinkerOS on the same board and it works fine rotated. My Raspberry PI 4 works fine rotated as well. What could be the problem with Armbian?

• 0

  Reputation Points

• 7 replies
• 6.5k views
• 2 followers

Igor

March 23, 20206 yr

Anyone have an issue where on a fresh install with apt update and upgrade I create a hotspot then have openvpn connect on boot. It works fine as a hotspot with 200mbps up and down but when the traffic is routes through a vpn by connecting openvpn the board will crash/become unresponsive if the upload is used heavily. Works great until I run a speedtest and on the upload the board will crash. Normal use is fine even pegging download causes no issue. Le potato s905x works amazing in this regard and never crashes period. Is this a known bug?

• 0

  Reputation Points

• 0 replies
• 2.7k views

bonedaddy4538

March 18, 20206 yr

There's an issue with Panfrost and Mesa 19.3 that causes X11 to crash in "OsLookupColor" which you may run into on Armbian on RK3399 devices; it can be solved by enabling the experimental branch in your /etc/apt/sources.list by adding the following line: deb http://deb.debian.org/debian experimental main contrib non-free You can then run 'apt update' and install experimental branch packages with 'apt -t experimental install <package>'. To fix the crash in X11, update the following from experimental: libegl-mesa0 libgbm1 libgl1-mesa-dri libglapi-mesa libglx-mesa0 mesa-va-drivers mesa-vdpau-drivers mesa-vulkan-drivers This should allow X11 …

• 0

  Reputation Points

• 0 replies
• 3k views

Neko May

March 12, 20206 yr

Where can I find a link to the source git for What source code are the 5.4.23-rockchip64 kernels from?

• 0

  Reputation Points

• 2 replies
• 3k views

Igor

March 6, 20206 yr

My ROC-RK3328-CC have 4GB Ram with 16GB eMMC, how to install the download "Armbian_20.02.1_Renegade_buster_current_5.4.20.7z" to eMMC and boot from eMMC? Thanks a lot!

• 0

  Reputation Points

• 2 replies
• 5.3k views
• 2 followers

sschnee

March 4, 20206 yr

Hi! I seem to have the same problem described here: I have an Asus Tinkerboard, not the S version. Today I upgraded from the latest Asus TinkerOS image: 20190821-tinker-board-linaro-stretch-alip-v2.0.11.img to: Armbian_19.11.3.346_Tinkerboard_buster_current_5.3.15_minimal.img I notice that my maximum CPU frequency has dropped from 1.80GHz to 1.61GHz. cpufreq-info now reports: $ cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware freq…

• 1

  Reputation Points

• 13 replies
• 7.1k views
• 2 followers

ginggs

February 22, 20206 yr

We talk about test of different parts. It was orginal one topic but split. The other is https://forum.armbian.com/topic/12936-how-to-control-fan-on-rockpro64 @deathisunknown Which kernel are you using? 5.3.xxx? Until this week end, I was using Ayufan's kernel in order to have ats working (I have the nas box with a harddrive so I want to have some ventilation). I've switched to Armbian's current kernel (5.3.xxx, I don't remember the exact subversion) and noticed that the fan would not spin. Then I tried Armbian's dev kernel (5.4.0-rc1) and my fan works fine. I stumbled upon this thread in the mean time, but since as I remember the lates…

• 0

  Reputation Points

• 17 replies
• 7.7k views
• 1 follower

soerenderfor

February 5, 20206 yr

Hi guys i am new on forum so i am sorry if this topic is in wrong place or if i badly look for answer in existing topics. I already using bionic legacy 4.4.199 destkop for few weeks and i am happy ( only problem which i have is with bluetooth-device manager not working aftar i connect keyboard or mouse and handsfree doesnt work too) but i see on web that there is new version so i download bionic 5.4.8 desktop to give a try. boot look normal until i get to tinkerboard login. there i use default root/1234 - it ask for changing root pass so i make it - then Retype pass and after enter it doesnt do anything. i can type anythong but enter only move…

• 1

  Reputation Points

• 7 replies
• 5.3k views
• 1 follower

TonyMac32

February 5, 20206 yr

Hi there, can anyone give me an URL that i can download an Armbian Stretch Release for the Tinkerboard S? I´ve Problems with my RPI-RF-MOD and i´m thinking it is something with the new Releases. Thx.

• 0

  Reputation Points

• 10 replies
• 5.4k views
• 1 follower

bennySB

January 29, 20206 yr

Tried booting a Renegade board with the Jan. 5, 2020 Buster Server Image. It appears that the eth0 is not starting. Switched to a Buster minimal from some time back, and at least the ethernet driver appears to be working.

• 0

  Reputation Points

• 5 replies
• 4.1k views

TonyMac32

January 24, 20206 yr

Hi all, I'm trying a Tinkerboard running armbian (minimal) and DietPi. My goal is to handle suspend and wake up. To enter in suspend mode i run 'echo mem > /sys/power/state'. I'm looking other ways to suspend .. by C application or by a signal on GPIO To wakes up I notes different modes on different OSes: - linaro pressing power button, pressing a key on usb+bt keyboard, pressing usb+bt mouse button - dietpi - pressing power button - armbian minimal - nothing ? my guess is that the board shuts down Please con you confirm? Where does reside this different behaviors? Thanks, regards. PS: is …

• 0

  Reputation Points

• 3 replies
• 4k views

Igor

January 23, 20206 yr

Hello, I'm unable to make the RTL8723BS chip on my Tinker Board to work on AP mode with the 5.4 kernel (same configuration works on legacy kernel). When I try to connect I get this error on dmesg: RTL8723BS: ap recv deauth reason code(3) sta:40:4e:36:cf:8a:18 On the console I also get a bunch of kernel errors similar to this: Message from syslogd@localhost at Dec 27 14:26:11 ... kernel:[ 799.239910] ff60: bf0377a4 dd8057e8 dd07ffac dd07ff78 c014a17c bf0377b0 de2d9128 de2d9128 Is this a known problem? Thanks

• 0

  Reputation Points

• 4 replies
• 5.4k views
• 1 follower

Ravaz

January 14, 20206 yr

See https://forum.pine64.org/showthread.php?tid=8685 Using his SPI flash image, and then using armbian-config flash from SPi/system on NVME option worked. I had commented out the set the uboot partition section to what is started booting from lines in boot cmd to do the initial testing. I have been booting mainline for a while on this device. It boots much faster, and two or three weeks agoTobias Schramms atf patch made into mainline atf so the device no longer hangs on a soft reboot. I have booted from sd, emmc and the NVME with this u-boot. I haven't tried usb3 or usb2.

• 0

  Reputation Points

• 3 replies
• 6.8k views
• 2 followers

belfastraven

January 10, 20206 yr

Hello, I'm trying to show a startup logo a Tinker Board without success. I tried to add a parameter logo=/boot/boot.bmp to /boot/armbianEnv.txt but it doesn't work. Is the boot logo implemented on the Tinker Board? Does it require a patch? Thanks for your feedback.

• 0

  Reputation Points

• 1 reply
• 3.7k views
• 1 follower

Igor

January 8, 20206 yr

Hello, is booting SPI + NVME supported on RockPro64? If I use armbian-config and installing system SPI + NVME will not boot the system. When using SD (mmc) + NVME is OK. SPI + USB also OK. Thank you for your help.

• 0

  Reputation Points

• 2 replies
• 3.7k views
• 1 follower

piter75

December 28, 20196 yr

Hi, because I find in 4r dont see any topic to talk more about change ramdisk as increase or decrease, so I make this cmt, hope somebody help me know + How to resize for ramdisk, and how to using sd card as ramdisk and swap file, so emmc size will be have more space, because I want install kali into + If using bionic desktop, and only install kali tool for pentest, will bionic running ok ? or I must build and install kali as root ? Hope someone can help me know it. Thank you so much

• 1

  Reputation Points

• 1 reply
• 6.3k views

Igor

December 21, 20196 yr

Dear all, I'm looking for help on having RFCOMM TTY working on a Tinker Board S. Any help will be welcome !! Using : Ubuntu Bionic with Armbian Linux 4.19.69-rockchip # uname -a Linux astrotinker 4.19.69-rockchip #5.95 SMP PREEMPT Mon Sep 2 07:34:36 CEST 2019 armv7l armv7l armv7l GNU/Linux I'm trying to have rfcomm tty working with a bt HC-05 dongle, but RFCOMM TTY seems not to be available. The BT HC-05 is well reconized and connected: # bluetoothctl [NEW] Controller 80:C5:F2:46:E2:C2 astrotinker [default] [NEW] Device 00:14:03:06:04:ED HC-05_TIC Agent registered # systemctl restart bluetooth.service # …

• 0

  Reputation Points

• 8 replies
• 7k views
• 1 follower

FranckM

December 19, 20196 yr

Hi all, I just bought TinkerBoard S and I downloaded Armbian Stretch 4.19 (tried both with and without desktop ) and I tried to boot. But no luck I was waiting for few mins but nothing. I also tried Armbian Strech 4.4 but also nothing. Am I missing something here? Original TinkerOS work without any issue Thank you for any advice/help

• 1

  Reputation Points

• 13 replies
• 20.3k views
• 1 follower

dragonlost

December 13, 20196 yr

I'm trying to make a script to run on the Pinebook Pro and I'm having mpp errors while trying to leverage it in ffmpeg. I'm not sure what might be causing the error but according to THIS THREAD , compiling with `-DHAVE_DRM='ON` should resolve it (which it doesn't in my case). I'm using the 20171218 release of rkmpp and ffmpeg 4.2. Any help is appreciated. mmp build: cmake -DHAVE_DRM='ON' -DCMAKE_BUILD_TYPE:STRING='Release' -DCMAKE_INSTALL_PREFIX:PATH='/usr' \ -DRKPLATFORM:BOOL='ON' -Wno-dev \ -DAVSD_TEST:BOOL='OFF' -DH264D_TEST:BOOL='OFF' -DH265D_TEST:BOOL='OFF' -DJPEGD_TEST:BOOL='OFF' \ -DMPI_DEC_TEST:BOOL='OFF' -DMPI_ENC_TEST:BOOL='OFF' -DMPI_RC2_TEST:BOOL='OFF' …

• 0

  Reputation Points

• 2 replies
• 5.4k views
• 1 follower

AndreVallestero

December 11, 20196 yr

Hi! I'm using Armbian with Ayufan's 5.3.0rc4 kernel (until ~1 month ago when I decided to freeze the dev kernels, they were not able to expose the pwmon for the fan that I need to keep running to cool my nas case). But I've seen lots of updates flying around about uboot. So I am wondering: are there significant improvements to uboot? I am currently using an old version of uboot on the SPI flash (so it is a little painful to test new version) and I am wondering if I should disable my SPI in order to have uboot on my emmc (to boot off the emmc) or if there is even a newer option to reflash my spi with a newer uboot... Thanks, Mathias PS: so…

• 0

  Reputation Points

• 0 replies
• 2.7k views

Mathias

November 25, 20196 yr

Hello people, I am trying to set CPU Governors but all the cores change to the same clock and cpufreq-info reports "CPUs which run at the same hardware frequency: 0 1 2 3", with that even one thread working is making the CPU scale up all clocks and heat more than it should, is there a way to unlink them and each one have their own clocks according to each core processing load?

• 0

  Reputation Points

• 0 replies
• 2.7k views
• 1 follower

Nikos Giannakas

November 17, 20196 yr

Hello, I'm using a RockPro64 boards inside one of my projects and I just noticed an issue related to the reset process. When pushing the reset button, the boards hangs in a reset loop. Using the oscilloscope, I found that the reset signal (OTP_OUT_H) is toggled every 330ms by the CPU and the only way to get it back to work is to power off the board, wait a few seconds, and power it back. The same issue is found if, after a working boot, a quick power cycle is performed. I tried disconnecting everything from the board but still, when pushing the reset button, the boards hangs in a loop condition (as if it’s constantly crashing at boot). …

• 0

  Reputation Points

• 5 replies
• 4.7k views

martinayotte

November 8, 20196 yr

Hi, Greatings for the team. Currently i am using Armbian Bionic Desktop image with my rockpro64. I went through this link for GPU supported libs installation- I can see there are libMali.so files in /usr/lib/aarch... folder. I also installed armnn from this link- https://developer.arm.com/solutions/machine-learning-on-arm/developer-material/how-to-guides/configuring-the-arm-nn-sdk-build-environment-for-tensorflow-lite/build-arm-nn And successfully done and tested. But when i am running on of my tenseflowlite based project, it is throughing error- Loaded model mobilenet_ssd.tflite resolved reporter nn…

• 0

  Reputation Points

• 0 replies
• 3.3k views

Rahul

November 6, 20196 yr

Hello all, I downloaded the Armbian Buster OS desktop version. I need to run it with a vertical display - portrait mode. The OS starts correctly and I see the desktop in landscape mode but when I try to rotate left the display, it does not rotate and return to landscape mode. The display is a large NBT monitor 1920x1080 that I need to rotate to 1080x1920. Any idea? Regards

• 0

  Reputation Points

• 17 replies
• 8.3k views

Igor

November 5, 20196 yr

Looking for a current realtime RTOS real time deb package or SD card image for the tinkerboard. I have been trying to compile a current real time build. All of my attempts have failed so far. free offer described below

• 1

  Reputation Points

• 29 replies
• 14k views
• 3 followers

berin

November 2, 20196 yr

Hello! I would like to know if it is possible to use the microUSB-Connector for connecting a USB device (a 7-port USB hub in my case)? My Tinkerboard is powered through the GPIO pins, so i don't use the microUSB for power input. Is it even possible from the hardware architecture of the board? Do i need some extra kernel packages and/or USB OTG to make it work? Thanks in advance, aElmecker

• 0

  Reputation Points

• 11 replies
• 8.1k views
• 3 followers

aElmecker

October 16, 20196 yr

I need one more component working. 3D and OpenCL. Has anyone successfully installed Panfrost on a RK3399 board ? Update! I manged to build the Panfrost X11 driver. Here's how I did it: https://panfrost.freedesktop.org/building-panfrost-mesa.html Before you create the build directory update the meson_options.txt file change platforms from auto to x11 change dri_driver from auto to swrast change gallium-drivers to panfrost cd to the build directory meson .. . -Ddri-drivers= -Dvulkan-drivers= -Dgallium-drivers=panfrost -Dlibunwind=false --prefix=/{wherever you want} ninja install …

• 1

  Reputation Points

• 28 replies
• 28.1k views
• 3 followers

Merblud

October 13, 20196 yr

Hi all experts, This is a serious issue for me as for one of the project i am using more than 20 numbers of rockpro64. I have installed them in my different locations of office. I have used two types of OS- *) LXDE-ubuntu-0.7.9-1067-arm64 *) bionic-containers-rockpro64-0.8.3-1141-arm64 Issue is- Whenever i flash these images to rockpro64, for some days autoboot works well such as if light goes and comes back then machines auto boot itself but after few days, auto boot does not happens with few machines and i have to press the "power button" to boot up. I thought with latest OS this issue will solve but same result with latest OS. …

• 0

  Reputation Points

• 2 replies
• 3.5k views

Rahul

October 3, 20197 yr

Greetings, After setting my tinkerboard pins 22 and 24 as an Inputs, they reverts to being an output pin on HIgh after around 30 seconds. What is the cause of this? Is this some kind of feature. I don't have this happen on any other pin other than these 2. iomari

• 0

  Reputation Points

• 11 replies
• 5.9k views
• 1 follower

iomari

September 25, 20197 yr

Greetings, On the tinkerBoard, I'm using python. I having difficulty understanding why the functions don't return the values that is expected according tho the library help. I'm using python3 and the ASUS GPIO library. import ASUS.GPIO as GPIO GPIO.setmode(GPIO.BOARD) This is the output from ipython: In [18]: help(GPIO.gpio_function) Help on built-in function gpio_function in module ASUS.GPIO: gpio_function(...) Return the current GP…

• 0

  Reputation Points

• 0 replies
• 2.7k views

iomari

September 25, 20197 yr

I am running armbian buster Armbian_5.91_Rockpro64_Debian_buster_default_4.4.184_desktop.img. I need rt_preempt in order to run linuxcnc. I started with the 5.0.21.tar.gz kernel source from <https://mirrors.edge.kernel.org/pub/linux/kernel/v5.x/> and the rt_preempt patch 5.0.21-rt16.patch.gz from <https://mirrors.edge.kernel.org/pub/linux/kernel/v5.x/>. I applied the patch to the kernel source and compiled it on a 4gb RockPro64. It boots fine into a remote terminal using ssh but there is no display on my HDMI monitor. The white LED is showing but the red LED is not lit. I had an earlier version of linux-5.0-rt running on armbian stretch so …

• 0

  Reputation Points

• 3 replies
• 4.3k views
• 1 follower

acondit

September 25, 20197 yr

Hi! I've had for quite a while the following error messages at startup: [ 39.095667] zswap: default zpool zbud not available [ 39.095670] zswap: pool creation failed This has happened with various 5.0, 5.1, 5.2 and now 5.3 kernels. Any idea what I should do to fix it? Mathias

• 0

  Reputation Points

• 6 replies
• 6.3k views

Mathias

September 11, 20197 yr

Hi I have a problem with change desktop language from en to polish. I tryed all solutions armbian-config , dpkg-reconfigure locales, export LANG. After reboot I got english desktop and locale info http://ecocut.pl/wp-content/uploads/2019/03/locale-1.jpg

• 0

  Reputation Points

• 4 replies
• 4.3k views

Kisuke-CZE

September 8, 20197 yr

I have 85 tinkers running with armbian 5.41 xenial next 4.14.23. Normally I run a script that apt upgrades them all but I run a small batch of them first as a test. Today I ran apt update/upgrade on three of them and they are all bricked. No output to the screen. Can't ping them. Any ideas?

• 1

  Reputation Points

• 70 replies
• 45.1k views

freak

September 3, 20197 yr

Hi, I am looking for a solution to have the JustBoom and HifiBerry Audio Hat with dtoverlays working like in the TinkerOS 2.0.8 Image from ASUS. Does someone known and has a procedure how to compile those and integrate in the Image or Compile a new kernel with its integration or a way to get those two hat's working? Many Thanks for your help Roman

• 0

  Reputation Points

• 9 replies
• 7.1k views

SecureXperts

September 2, 20197 yr

Hi, I spent several days trying to figure this out, which is a bit confusing given all the information that is available and posts and wikis saying that "Waveshare" LCDs are supposed to work, but something is still not right, hope you guys can help. What I have: ASUS Tinker Board S, flashed with Armbian_5.90_Tinkerboard_Debian_buster_default_4.4.182_desktop.img Updated to 4.19.57-rockchip via armbian-config (in order to get the fbtft* modules that were missing in 4.4). The LCD is a 3.5" original Waveshare 32a panel. I started by adding the overlay for this screen (i.e. my armbianEnv.txt has these overlays: overlays=i2c1 i…

• 0

  Reputation Points

• 10 replies
• 11.6k views

tastebin

September 2, 20197 yr

Does anyone have interest in this project? It looks quite promising! https://github.com/andreiw/rk3399-edk2/

• 1

  Reputation Points

• 5 replies
• 8.1k views
• 1 follower

Igor

August 26, 20197 yr

Hi, I am using rockpro64 board (based on rk3399 chip). OS- ubuntu18.04 linux. I am building a project that requires Vulkan support for gpu acceleration. Can someone please suggest how can i get vulkan driver for rk3399? Thanks.

• 0

  Reputation Points

• 1 reply
• 6.1k views

Tido

August 6, 20197 yr

Installed the desktop version of Armbian (bionic) on Asus Tinker Board S and noticed that the GPIO Pin 40 is always high on boot up. Please let me know whether this is high by default for any reason and if possible how to set it to Low while start up.

• 0

  Reputation Points

• 0 replies
• 2.9k views

Arun

August 6, 20197 yr

Hi! On my RockPro64, I usually run Armbian with Ayufan's 5.1 kernel (it runs very well and after manually compiling the dtb file most of the error messages at startup are gone). I've tried a few days ago to run Armbian's dev kernel (5.0), and both the sdcard and my usb3 attached ssd could not be detected. The network was also missing. I have pasted the output of armbianmonitor -U here. Mathias

• 0

  Reputation Points

• 2 replies
• 4.1k views

atula

August 4, 20197 yr

Update May-21-2018: script may have negative impact on HDMI audio, needs further investigation. Patches pushed to enable I2S HDMI device, but audio does not come out. Update Feb-20-2018: script update committed for out of the box audio support (both outputs and inputs) for ASUS Tinker Board. Available sinks: BT-VOIP SPDIF Headset (the jack) Available sources: BT-VOIP Headset-input (the jack) Tinkerboard sound is possible with Armbian, however I have not worked to get it set up "out of the box" because of a major bug in the sound itself, namely that it outputs pure high pitched garbage from certain ap…

• 1

  Reputation Points

• 53 replies
• 38.2k views
• 3 followers

zeekoe

July 28, 20197 yr

Anyone who typically updates on nightly kernels I would recommend freezing and not updating until we clear up some issues gifted us by some large amount of upstream changes that broke well, pretty much everything. I will update this thread as things get brought back to life. June 7th 2018: I've made a branch (rockchip-default) to work out the kinks. So far I have the board booting and Mali working again (with an initial error on load) , however there is no HDMI terminal, so initial boots would require a uart or SSH hdmi terminal is back thank you to Ntemis on github, I'd missed part of the conversation (I only have cell phone while at w…

• 1

  Reputation Points

• 16 replies
• 16.1k views
• 2 followers

TonyMac32

July 20, 20197 yr

5.1.0-1111-ayufan tag. Kernel crash when PCIE card is installed (thus pcie host root complex initialize). Will try previous tags soon, BTW, if anyone successfully run the "mainline" kernel with PCIE cards? [ 161.895780] io scheduler mq-deadline registered [ 161.897340] io scheduler kyber registered [ 161.911264] io scheduler bfq registered [ 162.136905] vcc5v0_host: supplied by vcc5v0_usb [ 162.740884] rockchip-pcie f8000000.pcie: no vpcie12v regulator found [ 162.746764] rockchip-pcie f8000…

• 0

  Reputation Points

• 0 replies
• 3.9k views

anonymoustemp

June 25, 20197 yr

Hi there, I'm trying to install docker on my tinkerboard s running armbian 5.73. I've managed the following steps from your documentation: sudo apt-key adv --keyserver pool.sks-keyservers.net --recv-keys 0EBFCD88 sudo echo "deb [arch=amd64] https://download.docker.com/linux/ubuntu bionic stable" > sudo /etc/apt/sources.list.d/docker.list sudo apt update But when i tried to install docker using: sudo apt install docker-ce I'm getting the error that docker-ce has no installation candidate. Does anyone maybe have an idea how to get this working? Thank you.

• 1

  Reputation Points

• 2 replies
• 5.1k views
• 1 follower

MEMEs

June 22, 20197 yr

Dear all, I'm running latest Armbian Bionic on Pine64 RockPro64, trying to connect a Midi Keyboard device (having several of them for testing), but it is not recognized by ALSA. If I run acconnect -l After connecting the keyboard, it's not listed (same behavior with different keyboards). Does anyone possibly knows what module might be missing in the kernel? Thanks..

• 0

  Reputation Points

• 7 replies
• 4.5k views

Igor

June 18, 20197 yr

Hi, I got my RockPro64 board several days ago, and got *UPSTREAM* kernel (v5.1-rc5) and uboot (v2019.04) running on it using Archlinux ARM. (Sorry guys, I like upstream and Alarm more) The pull request for uboot-rockpro64 can be found here: https://github.com/archlinuxarm/PKGBUILDs/pull/1691 The upstream kernel is in the official core repor of Archlinuxarm (and that's why I like Alarm so much). It boots and runs mostly OK on full upstream kernel/u-boot setup. On rc-kernel it even has HDMI output working, but no hardware acceleration. I'm waiting panfrost as the open-source driver, so far it doesn't matter much as I don't …

• 1

  Reputation Points

• 21 replies
• 10.8k views
• 1 follower

Mathias

June 13, 20197 yr

Hi all, I'm running Armbian 4.19 (both stable kernel 5.77 and nightly) on an TinkerBoard S. I'm trying to connect a 3.2inch resistive Touch Display to SPI2. The display works with ili9341 module on SPI2 CS0. I have the touch screen of it on the SPI2@1 (CS1) but no way of getting a module or overlay dts for the ADS7846 TouchScreen. I've seen, there is a generice resisitive-adc-touch module, but I can't get it running. Using the ADS7846 on armbian with AllWinner and several other boards for many years. Works great so far. Any hints, how to get it running in such a way, that it will be there with downstream updates (meaning without h…

• 0

  Reputation Points

• 17 replies
• 9.8k views
• 1 follower

TonyMac32

June 7, 20197 yr

I'm trying to get the RPI 7in touchscreen working on armbian with my Tinker Board. Can anyone tell me how?

• 0

  Reputation Points

• 1 reply
• 2.6k views

TonyMac32

June 3, 20197 yr

Scan ssid by mobile phone the SSID can be seen . but always in password loop. I've installed hostapd V2.7 and dnsmasq V2.79. and wpa_supplicant and networkmanager are stopped. The config files are as below: 1: etc/hostapd/hostapd.conf interface=wlan0 driver=nl80211 ssid=TinkerNet hw_mode=g channel=7 wmm_enabled=0 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=3 wpa_passphrase=mypassphrase wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP 2:/etc/dnsmasq.conf interface=wlan0 # Use the require wireless interface - usually wlan0 …

• 0

  Reputation Points

• 2 replies
• 3.8k views

SecureXperts

May 31, 20197 yr

I prepared (last weekend? - don't remember anymore) a first step towards a merge of rk3399 (currently nanopi boards) with rockchip64 (more or less all the rest) so that both can be covered fully under one boardfamily (rockchip64). Patches are adjusted and dts support for nanopis in ayufans kernel is done as well. https://github.com/chwe17/build/tree/rk3399merge I would happily give it into 'someone others' hands cause time in the next month might be really rare. Basically it needs testing on the boards which got newly merged into rockchip64 (don't own any nanopi *4 board so I can't test it). And probably a small helper script to adjust …

• 0

  Reputation Points

• 10 replies
• 6.1k views
• 1 follower

pkfox

May 28, 20197 yr

Hello. I wanted preempt-rt kernel for my armbian rockpro64 so i have compiled and generated preempt-rt 4.4.167 deb kernel package. I have installed my custom kernel deb package but after reboot the system boot in old kernel not the custom kernel. How i can set the system to boot from custom installed kernel ?(4.4.167-rt176 is my custom kernel) $ ls -a /boot . boot.cmd dtb-4.4.174-rockchip64 System.map-4.4.174-rockchip64 .. boot-desktop.png Image uInitrd armbianEnv.txt boot.scr initrd.img-4.4.167-rt176…

• 0

  Reputation Points

• 10 replies
• 9.3k views

rocksa

May 22, 20197 yr

I have spent a considerable amount reading docs and getting my head around building a custom default kernel & desktop image. Patching the kernel and optimising the desktop environment is working well. The remaining question is: How do I select a specific - kernel 4.4.174 (based on armbian-release 5.75) ? It defaults to 4.4.176 and 5.86.

• 0

  Reputation Points

• 2 replies
• 3.7k views

Roland G

May 19, 20197 yr

I downloaded the kernel source and kernel headers on a rk3288 rockchip (tinkerboardS) and noticed there was a mismatch between kernel version, armbian release and chipset (rockchip64) - see below. root@tinkerboard:~# uname -a Linux tinkerboard 4.4.174-rockchip #7 SMP Sun Feb 10 11:57:26 CET 2019 armv7l armv7l armv7l GNU/Linux root@tinkerboard:~# cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=tinkerboard BOARD_NAME="Tinkerboard" BOARDFAMILY=rockchip VERSION=5.75 LINUXFAMILY=rockchip BRANCH=default ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage root@tinkerboard:/usr/src# …

• 0

  Reputation Points

• 0 replies
• 2.4k views

Roland G

May 19, 20197 yr

Hi I need to do the following things on my Tinker Board S what i normally do on Raspberry Pi 3: raspi-config; system; Hardware; 5 interfacing options, 6 Serial Would you like a login shell to be accessible over serial? = No Would you like the serial port hardware to be enabled? = Yes then I need to add the following line in the /boot/config.txt dtoverlay=rpi3-minuart-bt This activates the Serial Console on /dev/serial0 Where do I config Serial and how? what is the correct dtoverlay for the miniuar-bt in tinkerboard? does anyone have a hint for me?

• 0

  Reputation Points

• 3 replies
• 7.2k views

martinayotte

May 17, 20197 yr

When connecting to the built-in wifi adapter (wlan0) on the tinkerboard S (rockchip 3288), the kernel produces a stacktrace and clients can't connect. [ 839.074341] kernel BUG at mm/slub.c:3904! [ 839.078825] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM - (see http://ix.io/1J1n) Is there a fix for this?

• 0

  Reputation Points

• 3 replies
• 3.9k views

Igor

May 15, 20197 yr

Hi I was wondering of status of vanilla kernel and linux for ROC-RK3328-CC. I read an article about it being mainlined in 4.17 (http://bbs.t-firefly.com/forum.php?mod=viewthread&tid=2312) but I still see people working through issues on this board. I am mainly interested on ethernet and USB3 support. Not interested in video or sound, although others might. Thought this is the place to ask as there is a lot going on but difficult to scrape all the info on the threads. Thanks!

• 0

  Reputation Points

• 2 replies
• 5.5k views

TonyMac32

May 14, 20197 yr

We are looking at replacing the raspi3b+ with the tinkerboardS (rockchip 3288) in an embedded system, running armbian (bionic-4.19). Initial tests show that OS stability, board performance and form factor make the tinkerboardS a good substitute for the raspi. However, one issue we have run into is a conflict with pin 32 of the GPIO which is used by the hostboard for managing output devices. We have tried to turn off serial2 by removing the UART2 overlay and adding 'console=display' in /boot/armbianEnv.txt and also disabling & masking serial-getty@ttyS2.service but that hasn't stopped pin 32 from being chatty when connected to the hostboard. Is…

• 0

  Reputation Points

• 5 replies
• 6.3k views

Igor

May 12, 20197 yr

Hi, I'm running Armbian Stretch on a Tinker Board and trying to use a one-wire thermometer. I have this in /boot/armbianEnv.txt: overlays=i2c1 i2c4 spi2 spidev2 uart1 uart2 w1-gpio However, when I boot the board, I see this in dmesg: [Wed May 8 17:38:43 2019] rockchip-pinctrl pinctrl: unable to find group for node w1_pins [Wed May 8 17:38:43 2019] w1-gpio: probe of onewire@0 failed with error -22 Kernel version is Linux tinkerboard 4.19.33-rockchip #5.77 SMP PREEMPT Wed Apr 3 17:06:29 CEST 2019 armv7l GNU/Linux Any ideas? I'm using the rockchip-w1-gpio.dtbo that was installed with the system. Regards, Dianne.

• 1

  Reputation Points

• 3 replies
• 4.4k views

Dianne S.

May 10, 20197 yr

Dear All, I am running a project with Tinkerboard and a gigE camera. Trying to take video image through gstreamer (gst-launch). The camera is an Imaging source camera (DFK 33GX249) and I am using the linux library (https://github.com/TheImagingSource/tiscamera) for developing apps. My Tinkerboard is running Armbian Stretch (Armbian_5.50_Tinkerboard_Debian_stretch_next_4.14.52_desktop) Everything is working perfectly untill I am trying to run the command below: tinker@tinkerboard:~$ TCAM_LOG=DEBUG gst-launch-1.0 --gst-debug=tcamsrc:5,tcambin:5 --gst-debug-no-color tcambin ! videoconvert ! autovideosink The output is: Spoiler …

• 0

  Reputation Points

• 2 replies
• 2.7k views
• 1 follower

Igor

May 8, 20197 yr

I'm using Armbian on a Tinker Board S. I did the installation back when the 4.4 kernel was still the default one. I expected that I'd get the newer 4.19 kernel by using 'apt update && apt dist-upgrade' at some point as it would become the new stable. This does not seem to be the case however, as I see the new downloads use 4.19 by default, but the stable package still points to a 4.4 kernel. Is it recommended to just move up by installing the kernel package with the next suffix or are there still reasons to wait with upgrading?

• 0

  Reputation Points

• 12 replies
• 7.4k views
• 1 follower

sfx2000

May 4, 20197 yr

While running the debian stretch desktop, I'm able to set my scroll direction in the mouse/touchpad manager but only certain programs respond to the changes. The file manager and leafpad do but chromium and the terminal window don't. Anyone know anything about this?

• 0

  Reputation Points

• 0 replies
• 2.8k views

AZClusterboard

May 3, 20197 yr

I try to understand the usage of Tinkerboard for Industrial Application usage, we have below questions. 1. Operating temperature is between 0-60 C [as many Industrial PLCs recommend 0-55 C only] 2. Long Term Supply of the Boards 3. Bulk Quantities buying [Get 30 to 50 boards in 2-4 weeks notice] The board and quality seems top notice, RPI interface is good for our use cases, anyone sees a risk in above points or would like to suggest something? We are looking a good sized community, Ubuntu OS, much stable and better performing board compared to Raspberry PI, all seems good with Tinkerboard. Please share your idea…

• 0

  Reputation Points

• 14 replies
• 8.1k views
• 1 follower

Gops

May 2, 20197 yr

I am using this image https://dl.armbian.com/rockpro64/nightly/Armbian_5.82.190422_Rockpro64_Debian_stretch_dev_5.0.0.7z Board start only without wifi & pcie. But i got this error. https://pastebin.com/gq2DpXaF

• 0

  Reputation Points

• 0 replies
• 3k views

FrankM

April 22, 20197 yr

I put a TinkerBoard in a Pi-Top CEED and using TinkerOS 2.0.8 it boots and the LCD works fine. Using Armbian it looks like it boots but nothing is displayed on the LCD. The Pi-Top CEED uses a HDMI to 30-pin converter board and the current LCD is a 1920x1080 14in that I used to upgrade the original. Any ideas why the Raspberry running Raspbian and The Tinkerboard running TinkerOS would work with the display but Armbian wouldn’t?

• 0

  Reputation Points

• 27 replies
• 8.8k views
• 1 follower

mark-aus-51

April 19, 20197 yr

Mar 9 12:31:24 renegade liblogging-stdlog: [origin software="rsyslogd" swVersion="8.24.0" x-pid="1209" x-info="http://www.rsyslog.com"] rsyslogd was HUPed Mar 9 12:31:28 renegade systemd[1]: Stopped Serial Getty on ttyS2. Mar 9 12:31:28 renegade systemd[1]: Started Serial Getty on ttyS2. Mar 9 12:31:38 renegade systemd[1]: Stopped Serial Getty on ttyS2. Mar 9 12:31:38 renegade systemd[1]: Started Serial Getty on ttyS2. Getting the bootloop serial getty message on my Libre Renegade OMV4. Logs enclosed. I tried some of the fixes I saw on other threads but to no avail. Those looked like they were for diff devices, but may be CPU specific? Any ide…

• 0

  Reputation Points

• 2 replies
• 3.3k views
• 2 followers

weehal

April 15, 20197 yr

Just reporting that there is some tx-offload bug in the ASUS Tinker Board Rockchip. I think I read about this issue regarding other rockchip/platforms when checksum offload bugs on large packets. When I run ethtool -K eth0 tx off I stop having issues with NFS over TCP The last part of diagnosis is when I forced a NFS crash by enabling tx offloading.

• 0

  Reputation Points

• 0 replies
• 3k views
• 1 follower

Nitrax

April 12, 20197 yr

It seems that If I use the mainline kernel Ethernet does not work, in the sense that it doesn't even get initialized. ip addr will only show the loopback interface, and the kernel log will show this regarding the ethernet port. Could it be a device tree issue? [ 6.867997] rk_gmac-dwmac ff540000.ethernet: PTP uses main clock [ 6.868097] rk_gmac-dwmac ff540000.ethernet: Linked as a consumer to regulator.5 [ 6.868103] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input). [ 6.868112] rk_gmac-dwmac ff540000.ethernet: TX delay(0x25). [ 6.868118] rk_gmac-dwmac ff540000.ethernet: RX delay(0x11). [ 6.868126] rk_gmac-dwmac ff540000.ethernet: integr…

• 0

  Reputation Points

• 13 replies
• 8.5k views
• 2 followers

jpegxguy

April 8, 20197 yr

Hi! I connect my 1366x768 monitor to Tinkerboard, but resolution sets to 1280x720. $ xrandr Screen 0: minimum 320 x 200, current 1280 x 720, maximum 8192 x 8192 HDMI-1 connected 1280x720+0+0 (normal left inverted right x axis y axis) 410mm x 230mm 1920x1080 60.00 + 1280x720 60.00* 720x480 60.00 Yes, i tried set timings manualy. I set native from edid: Modeline "Mode 0" 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync But after applying this modeline: - monitor detects 1280x720 resolution instead of 1366x768 - crops image as 1024x768 - have many noises and waves on screen... very unstable image (pixel clock 8…

• 1

  Reputation Points

• 11 replies
• 10.2k views
• 1 follower

berin

April 7, 20197 yr

Hey, maybe a stupid question, but how I can change the i2c clock rate in the armbianENV.txt? I have search around the forum and didn't find anything. can someone point me in right direction? Greets

• 0

  Reputation Points

• 2 replies
• 3.4k views

martinayotte

April 2, 20197 yr

Hi so there is a wip for RockPro64 but Kernel development and some other builds like MrFixIt have made gr8 advancement. Wondering if you could start support for rp64 or maybe update the wip since kernel has greatly improved.

• 0

  Reputation Points

• 1 reply
• 3.2k views

Igor

March 31, 20197 yr