Rockchip

Hi all! I have a problem with Armbian images on kernel 5.10.160 (jammy & bookworm Armbian_23.11.1_Orangepi5-plus_***_5.10.160.img) When starting from the SD card the nvme device is not visible root@orangepi5-plus:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS mtdblock0 31:0 0 16M 0 disk mmcblk1 179:0 0 58G 0 disk ├─mmcblk1p1 179:1 0 256M 0 part /boot └─mmcblk1p2 179:2 0 57.1G 0 part /var/log.hdd / mmcblk0 179:32 0 233G 0 disk mmcblk0boot0 179:64 0 4M 1 disk mmcblk0boot1 179:96 0 4M 1 disk zram0 254:0 0 7.7G 0 disk [SWAP] zram1 254:1 …

• 0

  Reputation Points

• 1 reply
• 1.9k views
• 1 follower

ozacas

March 27, 20242 yr

Hello, I have roughly 30 Orange Pi 5 here in the office setting up for deploying in the field. NVMe boot is working great after using 'nand-sata-install' to flash the MTD. But sometimes (rarely, but happens), when issuing a reboot of Armbian, after full kernel shutdown, the player does not boot back up. Power light is on, no activity blinking LED. Network link and activity blinking. Just won't boot. Requires physically disconnecting power for a few seconds then re-plug to get to boot. I have watchdog set in Armbian and tested that works. So this seems to be before Linux kernel has taken control. Is there any way to enab…

• 0

  Reputation Points

• 33 replies
• 19.7k views
• 2 followers

nihilowy

March 27, 20242 yr

Hi, I was just trying to test locally build image with edge kernel (Armbian_23.11.0-trunk_Orangepi5-plus_bookworm_edge_6.6.0-rc1.img) by flashing it on SD card and then trying to boot off it in my Orange Pi 5+. The board just sits there with the LED blinking and that's it. The legacy kernel image (Armbian_23.11.0-trunk_Orangepi5-plus_bookworm_legacy_5.10.160.img) boots fine. Do I have to carry out some extra step(s) to test the edge kernel? It's not a show-stopper for me as I have legacy image booting of EMMC nicely (and I am running jellyfin in docker happily there). It's just I thought I might test out some bleeding-edge s…

• 0

  Reputation Points

• 5 replies
• 4.3k views

Vijay Gill

March 25, 20242 yr

Hello friends: I have opi5 with the spi removed, which spiloader do I use to boot from the sd card? Thank you so much

• 0

  Reputation Points

• 1 reply
• 1.8k views
• 1 follower

Werner

March 25, 20242 yr

Hello ! Not found any devices How to make it work? hciconfig -a hci0: Type: Primary Bus: USB BD Address: E8:48:B8:C8:20:00 ACL MTU: 1021:6 SCO MTU: 255:12 UP RUNNING PSCAN RX bytes:1537 acl:0 sco:0 events:148 errors:0 TX bytes:3430 acl:0 sco:0 commands:136 errors:0 Features: 0xff 0xff 0xff 0xfe 0xdb 0xfd 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH HOLD SNIFF PARK Link mode: PERIPHERAL ACCEPT Name: 'orangepi5' Class: 0x000000 Service Classes: Unspecified Device Class: Misce…

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Michael Robinson

March 22, 20242 yr

Hello, I am using Armbian 23.8.2 Jammy for Orange Pi 5 PLus and it cannot diplay 4K via HDMI. How to enable/switch this on?

• 0

  Reputation Points

• 6 replies
• 5.4k views

thanh_tan

March 22, 20242 yr

My current TV doesn't have CEC but I'm planning to replace it with something that has CEC support and would really like to automate the on/off thing... Is cec-utils supported or is there an alternate kernel API?

• 0

  Reputation Points

• 2 replies
• 3.6k views
• 1 follower

OttawaHacker

March 18, 20242 yr

Hello! I would like to connect orangepi-4-lts to ili9341. I have new blank Armbian. $ uname -a Linux orangepi4-lts 5.15.52-rockchip64 #22.05.4 SMP PREEMPT I did overlay based on allwinner: /dts-v1/; /plugin/; / { compatible = "rockchip,rk3399"; fragment@0 { target = <&gpio1>; __overlay__ { ili9341_pins: ili9341_pins { pins = "PC7", "PD0"; function = "gpio_out", "gpio_out"; }; }; }; fragment@1 { target = <&spi1>; __overlay__ { status = "okay"; cs-gpios = <&gpio1 10 1>; ili9341: ili9341@0 { compatible = "ilitek, ili9341"; reg = <1>; pinctrl-names = "default"; …

• 0

  Reputation Points

• 4 replies
• 5.3k views
• 1 follower

Spartan

March 16, 20242 yr

I built armbian using the branch 23.11 with legacy-kernel 5.10.160 for use as a Nextcloud server. Version: Armbian-unofficial 23.11.0-trunk Bullseye \l . 5.10.160-legacy-rk35xx After running sudo apt upgrade there were a few packages which were being upgraded successfully from 23.11.0-trunk to 23.11.1. Unfortunately the package armbian-bsp-cli-orangepi5-plus-legacy cannot be upgraded to 23.11.1 due to the base-files still being on 23.11.0-trunk. The system is running fine though. $ sudo apt update && sudo apt list --upgradable Hit:2 http://deb.debian.org/debian bullseye InRelease Hit:3 http://deb.debian.org/debian bullseye-updates InRe…

• 0

  Reputation Points

• 3 replies
• 3.8k views

Guest

March 15, 20242 yr

Hello, i'm using Armbian 23.11 Jammy-amazingfated Gnome. Kernel 5.10 If to seek a couple of times in h264 1080p BD remux'es it will cause system restart. Any video players are affected. Tried mpv, vlc, kodi and others. Problem affect just h264 1080p remuxes, that typically are 30..40 Gb, smaller h264 or even larger h265 files seem to work fine. I tried fresh install of armbian, where no rkmpp is installed, then h264 files plays/seeks fine, in software mode of course. Once I did sudo update/upgrade, that also installs rkmpp and other rockchip stuff, then videos start to play with rkmpp and problem is back. I've tried disabling hw deco…

• 0

  Reputation Points

• 4 replies
• 2.8k views

noba

March 13, 20242 yr

I wanted to share 2 custom overlays I've created and tested for the RockPi E to enable UART1 and OTG via the GPIO. Create file rockchip-uart1.dts /dts-v1/; / { compatible = "rockchip,rk3328"; fragment@0 { target-path = "/serial@ff120000"; __overlay__ { pinctrl-0 = < 0x23 >; status = "okay"; }; }; }; Create file rockchip-otg.dts /dts-v1/; / { compatible = "rockchip,rk3328"; fragment@0 { target-path = "/usb@ff580000"; __overlay__ { dr_mode = "otg"; }; }; }; Install and enable overlays: sudo armbian-add-overlay rockchip-uart1.dts sudo armbian-add-overlay rockchip-otg.dts

• 1

  Reputation Points

• 8 replies
• 9.1k views

ich777

March 12, 20242 yr

Hi Team, I want to build or get pre-built armbian image for kernel 4.4 with wifi : rtl8723as enabled. Please help or provide any suggestion to build armbian image for rockpi-e. Any help or suggestion will be appriciated.

• 0

  Reputation Points

• 3 replies
• 3.1k views
• 1 follower

Bhavin

March 6, 20242 yr

I just installed with the latest KDE image, but I'm able to reproduce this with any of the images available. After going through the initial configuration, wifi works great. I updated apt and upgraded everything. Then I installed the armbian-firmware-full package. After rebooting wifi still works. Then I setup Bluetooth for my mouse and keyboard. They work correctly. After rebooting I no longer see any networks to connect to for wifi. If I disable Bluetooth and reboot wifi works again and so does Bluetooth. Is this an issue of daemons or drivers loading in the wrong order?

• 0

  Reputation Points

• 0 replies
• 1.6k views
• 1 follower

oorrwullie

March 6, 20242 yr

I just installed with the latest KDE image, but I'm able to reproduce this with any of the images available. After going through the initial configuration, wifi works great. I updated apt and upgraded everything. Then I installed the armbian-firmware-full package. After rebooting wifi still works. Then I setup Bluetooth for my mouse and keyboard. They work correctly. After rebooting I no longer see any networks to connect to for wifi. If I disable Bluetooth and reboot wifi works again and so does Bluetooth. Is this an issue of daemons or drivers loading in the wrong order?

• 0

  Reputation Points

• 0 replies
• 1.2k views
• 1 follower

oorrwullie

March 6, 20242 yr

Hello I'm running the NAS on Orange PI 5. I've run Armbian with EDK2 from https://github.com/armbian/build/pull/5900. The system starts from SSD disk connected via PCIE card with 4 SATA ports. I wanted to run simple fan control via GPIO, but setting the value 1 or 0 on GPIO has no effect and the multimeter connected to GPIO always shows 2.85V. How I did it. I installed wiringOP as the manual says. I selected GPIO 0 and entered the commands gpio mode 0 out gpio write 0 0 I connected a multimeter to GPIO 0 but it always shows 2.85V when I did gpio write 0 1 the multimeter also shows 2.85V gpio readall shows 1 in column V when "gpio write 0 1" com…

• 0

  Reputation Points

• 3 replies
• 2.6k views

Baxi

March 6, 20242 yr

I'm trying to update python on my armbian bookworm to 3.12 but I cannot find any packages for bookworm. I regret not going with the ubuntu one now 😕 because that one has the deadsnake packages. Any known alternatives? (beside compiling your own packages)

• 0

  Reputation Points

• 2 replies
• 10.3k views
• 1 follower

OttawaHacker

March 6, 20242 yr

Hello, as already mentioned in topic USB C port doesn't work after upgrading to the latest kernel 6.6.2 . The previous problem with not working left usb 3 port persist no more. Everything is fine. As I remember , before update the usb c port has worked with the adapter and the devices like mouse, usb flash etc. Now it doesn't work any more, furthermore it gives no signal of life. There is 0 amps current measured, also dmesg -W gives no output at all after plugging in the device. PS: I was unable to upload the report file, also the service paste.armbian.com doesn't work at the moment.

• 1

  Reputation Points

• 6 replies
• 4.4k views

pinebookpro-owner

March 4, 20242 yr

I have a RockPro64 that I have been using for many years as a server. It is currently running Armbian bookworm 12.5. Most of the storage is on an M.2 SSD attached to the PCI socket and is subdivided into disk volumes using linux LVM2. Today I accepted the Armbian kernel upgrade from 6.1.50 to 6.6.16 During the reboot it failed to mount any of my LVM volumes because the device nodes where not present. I found this article about how to recover the situation: https://unix.stackexchange.com/questions/11125/lvm-devices-under-dev-mapper-missing While in rescue mode I ran the suggested command vgchange -a y <name of volume gr…

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

David Pottage

March 3, 20242 yr

Well, I am trying to flash armbian to my board, but after I run upgrade_tool ef in mistake. I can't do anything via maskrom/loader at all wherever Windows or linux. Then I try to unbrick it via flash the "MiniLoaderAll.bin" via "upgrade_tool db" and "ul" but them don't work at all(Timeouted),How can I do with it?

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

calvin lin

March 2, 20242 yr

A new variation of Orange Pi 5 is now available. I think it's available on AliExpress, but I've seen the item on Amazon.com as well...reasonable price: https://www.amazon.com/Orange-Pi-Rockchip-Frequency-Development/dp/B0C5BZLPZN It comes now with the RK3588 instead of the RK3588s of the 5 and 5B. It's similar in capabilities of the Rock 5B but I believe has a few more bells and whistles. It has two 2.5GB ethernet ports. Separate connectors than GPIO for RTC and fan. Full size HDMI input as well as 2 full size HDMI outputs. Can have m.2 for 2230 WiFi/BT on top side as well as m.2 2280 on bottom of board. I think it can only go up to 16GB me…

• 1

  Reputation Points

• 42 replies
• 44.3k views
• 9 followers

Zaerc

March 1, 20242 yr

Is it possible to use the onboard microphone of Orange Pi 5 on Armbian? It does not seem to turn on

• 1

  Reputation Points

• 4 replies
• 3.6k views
• 2 followers

BOFFBOY

February 28, 20242 yr

I'd like to congratulate you for a great release (24.2.1) with KDE! I was looking for a guide to install KDE in a minimum version, but I could not trim it down enough, and this release solved my issues. Everything is working smoothly, video acceleration is there, Wi-Fi (AX210) is there, bluetooth is there! A real pleasure to use. Best, team!

• 1

  Reputation Points

• 1 reply
• 1.9k views
• 1 follower

BOFFBOY

February 28, 20242 yr

Hi guys. I have been using a RockPro64 as a miniserver for many years. It runs stable most of the time. I have assigned it a host name "ab2" via armbian-config. It usually responds well to this alias. Only from time to time it happens that it no longer responds to the hostname. Only a reboot helps. Do you have any idea what this could be? PS Thanks for your great work! Sem

• 0

  Reputation Points

• 1 reply
• 2.3k views
• 1 follower

CryBaby

February 23, 20242 yr

Hi, I went to see if there were any updates to the OPi5+ images and saw the OPi5 had updates. I clicked on the link on the main download page. https://www.armbian.com/orangepi-5/ https://redirect.armbian.com/orangepi5-plus/archive/ I've come back and now it has desktop images but no server images.

• 0

  Reputation Points

• 8 replies
• 4.6k views

Werner

February 16, 20242 yr

Hi, I've been running Armbian legacy server on my 5+ for a month now. I had trouble initially with my EMMC not booting, but I discovered, I had to wipe the SPI Nor then using Armbian config to flash it, then write to EMMC. When a new version of Armbian comes out for the 5+ and it may be a 6.8 kernel build, will I need to re-flash the SPI before I can install the newer version of Armbian (or another image from that's not Armbian?) before updating the EMMC. I found the steps on the Radxa site insightful for a general overview of SPI Nor and flashing (I understand it not an OPi5 x board), but it's not clear to me if a different OS will ne…

• 0

  Reputation Points

• 0 replies
• 3.2k views

Thewonderer

February 16, 20242 yr

Hi, I have orange pi 5. I searched all over internet for information how to set on startup/power on GPIO pins behavior, but i cannot find anything. Most of GPIO pins are set to IN mode 1. Sadly I need them to output mode 1. I am scared something could burn this way since i set them to though wiringPI after kernel boot sequence is complete. Can some one give information how I can set them up at earlier point when I power on the board? I found that DTB/DTS file could do it. But there is no clear information / pin addresses I should set. Thanks in advance! Regards!

• 0

  Reputation Points

• 0 replies
• 1.9k views
• 1 follower

David Parushev

February 15, 20242 yr

I want to share some information about an issue that I see on my OPi5+. Since I got it I am messing around with it and everything works great so far with the edge 6.7 kernel. One thing I noticed though was, that right after installation with nothing connected and when idle, there was one kernel process that was constantly consuming around 10% CPU time and the load stays at 1. The process was irq/136-hym8563. The number varies of course after each boot. Kernel driver is rtc_hym8563. Since it is build into the kernel I was not able to unload it as a first test. Side node, the issue is not seen on the Rock5b, so it seems OPi5+ hardware specific. Even if bot…

• 1

  Reputation Points

• 7 replies
• 5.1k views

Werner

February 14, 20242 yr

Hi, Thank you for maintaining this excellent distribution, I have tried out this evening, via SD card, the new Armbian 23.11 Bookworm CLI Kernel 6.7 and I wanted to share some feedback on it along with some queries please: 1) HDMI works connected to my 4K Samsung TV, although I had to turn off "Input Signal Plus" for it to display the console correctly, otherwise there were all manner of green rectangles and other screen corruption present. Turning off "Input Signal Plus" fixed this straight away. 2) I cannot access either of the SSDs I have connected to my powered USB 3 hub. I tried with the hub connected to the USB-C port …

• 0

  Reputation Points

• 47 replies
• 20.4k views
• 1 follower

sugatam

February 13, 20242 yr

I have been working on rk3328 (kernel 6.1) based board recently and have been trying to bringup wifi RTL8723AS module using rockpi-e image. As there is no direct support available for this module I have tried to cloning it from github and building it but it gives compilation errors. Hence I referred to drivers available in the kernel and found one for the module similar to that of my module (RTL8723BS), cross verified through user manual and datasheets and build it using armbian. The driver gets built properly and even initializes upon powerup but it isn't getting into probe. The wifi is interfaced through SDIO to the board. Any idea what might b…

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

Bhavin

February 8, 20242 yr

I've got Orange Pi 5 Plus board with 16 Gb of RAM, 256 Gb of eMMC, Realtek RTL8852BE-CG wireless module. SD card is Samsung EVO Plus 32Gb. I tried to run Armbian images on this board (from the SD-card I've mentioned before) but it was absolutely failed. I tried 5 images: Armbian_23.11.1_Orangepi5-plus_jammy_legacy_5.10.160_gnome-amazingfated_desktop.img.xz Armbian_23.11.1_Orangepi5-plus_bookworm_legacy_5.10.160.img.xz Armbian_23.11.1_Orangepi5_jammy_legacy_5.10.160_gnome-amazingfated_desktop.img.xz Armbian_23.11.1_Orangepi5-plus_bookworm_edge_6.7.0-rc1.img.xz Armbian_23.11.1_Orangepi5-plus_jammy_edge_6.7.0-rc1.img.xz which…

• 1

  Reputation Points

• 27 replies
• 20.2k views
• 2 followers

ozacas

February 6, 20242 yr

Hi gals & guys, Came over to this forum from the OPI forums which seem.. rather low on real-user activity. I am quite new to the SBC Arm64 platform and have many questions. I am an experienced sysadmin on x86/amd64 and still figuring out the differences. I bought a Orange Pi 5 Plus 32G of RAM and i am running of the 256G emmc. I am able to run different OS's (OPI-Ubuntu, OPI-debian, plain Ubuntu and Armbian). As i intend to use the board as server i didn't look into Android and the like.. My plan is running (OMV) from the emmc and attaching ZFS storage by means of a nvme-to-sata adapter and providing iscsi storage from there to my home-lab with my VM's …

• 0

  Reputation Points

• 9 replies
• 15.4k views

Marco Schirrmeister

February 4, 20242 yr

Hmm, seems i need someone holding my hand all steps of the way 😇. Soon i'll need to pay some.. 🥰 I got my OPI5plus working from emmc with nvme-to-sata adapter on edge kernel and now i have 5 HDDs and 1 SSD connected to it. Intended for ZFS with cache... But : ZFS module won't build. I installed linux-headers and tried # apt install zfsutils-linux zfs-dkms. --- Setting up zfs-dkms (2.1.9-2ubuntu1) ... Loading new zfs-2.1.9 DKMS files... Building for 6.7.0-rc1-edge-rockchip-rk3588 Building initial module for 6.7.0-rc1-edge-rockchip-rk3588 configure: error: *** None of the expected "bops->release()" interfaces were detected. …

• 1

  Reputation Points

• 7 replies
• 6.2k views

QuaxEros

February 4, 20242 yr

I installed Armbian 23.11 Bookworm Kernel 6.1, Size: 482Mb, Release date: Nov 30, 2023. After installation, a CH340 based board was connected to my original Tinkerboard and recognized. Subsequently, I used armbian-config to provide the default desktop (Cinnamon flavor). Thereafter, the CH340 board is incompletely recognized. Specifically, no device is presented as /dev/ttyUSB?. The device appears in the list from lsusb, the kernel module ch341.ko loads, but no device in /dev. The forum search shows a previous instance of a similar issue many years back. I attempted to build the driver from wch.cn, but the kernel sources pulled from armbian-config were for the Linux tinker…

• 1

  Reputation Points

• 6 replies
• 4.5k views
• 2 followers

dgw

February 2, 20242 yr

I have a custom PCIe x4 lane card that I'm trying to integrate with a RockPro64 SBC. This custom card has been tested with many users on different platforms including a linux x86 system. When I try this card in a RK3399 system, I get a strange result when I view the assigned address space with the lspci command. It appears the address assigned is the exact value of the BAR address size for each BAR. If I change the BAR size the assigned address changes to that value. Below is a dmesg dump along with a lspci output for my device. Device is [ad00:001e]. Any guidance? dmesg: [ 2.395091] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges: [ …

• 0

  Reputation Points

• 2 replies
• 3.3k views

JHadd

January 28, 20242 yr

Hello, I tried to setup a network bridge on the Orange Pi 5 to utilize with Qemu/KVM and some virtual machines I have. Here is my armbianmonitor output: https://paste.armbian.com/dajivikohi I edited /etc/netplan/armbian-default.yaml and modified it to setup a simple network bridge. I've done this countless times on other hardware I have. I rebooted, but the bridge fails to initialize and the screen gets an error dumped out every 5-10 seconds: rk_gmac-dumac: fe1c0000.ethernet eth0: Adding VLAN in promisc mode not supported rk_gmac-dumac: fe1c0000.ethernet eth0: failed to initialize vlan filtering on this port Is bridg…

• 0

  Reputation Points

• 4 replies
• 7k views

Oskar Enoksson

January 26, 20242 yr

Hi, I tried to connect an external USB 3.2 gen 2x2 4TB SSD drive to the only USB-C port available on the Rockpro64, but it's not recognized. I don't know if I need to install some packages for it to work? Any help would be very appreciated! I am on Ubuntu Jammy based Armbian: 6.1.63-current-rockchip64 #1 SMP PREEMPT Mon Nov 20 10:52:19 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux It works well with the same cable on a Macbook Pro. Kind regards, Baptiste dmesg [ 4.879030] usb usb1-port1: Cannot enable. Maybe the USB cable is bad? [ 4.880111] [drm] Initialized panfrost 1.2.0 20180908 …

• 0

  Reputation Points

• 1 reply
• 2.3k views

Baptiste

January 25, 20242 yr

On a fresh install from the website on kernel 6.1 bookworm/Jammy when rebooting the board a kernel panic occurs and the device will not boot unless power cycled. This was not the case even a few months ago on a 6.6 edge kernel. I also tried the current edge 6.7 kernel and the board wouldn't boot at all not that I expected it to. The board says 3308B on the chip(samsung memory) and ive also tried two different micro sd. Anyone else having this issue? Serial output is below of the relevant failure Thanks for anyone willing to look. Update: Reboot works fine on rockpi-s ordered more recently late 2023 with non-samsung ram mo…

• 0

  Reputation Points

• 1 reply
• 2.7k views

bonedaddy4538

January 25, 20242 yr

Needed/wanted to add Bluetooth to my OPi5 and also needed WiFi at the same time. Did not want to use 2 USB ports so I tried the T2UB. Working well. Bluetooth appeared on my Armbian Ubuntu Jammy setup and I plugged in the dongle. It saw a few of my bluetooth devices. Reason I wanted bluetooth is to use a controller for some games/emulators. I'll make another post for that. My PS4 Dualshock controller is not showing up in the list of devices. My version is an older version, Armbian 23.06.420 Jammy with Linux 5.10.160-rk35xx No end-user support: built from trunk Conclusion: TPLink T2UB should work properly on Armbian Ubuntu desktop.

• 0

  Reputation Points

• 0 replies
• 1.3k views

ArmBoy1988

January 24, 20242 yr

Installed: Armbian_23.11.1_Orangepi5-plus_bookworm_edge_6.7.0-rc1 The analog device is visible, but there's no sound from the headphone jack. The hdmi device is not visible. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Analog [Analog], device 0: fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0 [fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0] Subdevices: 1/1 Subdevice #0: subdevice #0 There is no sound when I play a test file: aplay -D hw:0,0 /usr/share/sounds/alsa/Noise.wav Playing WAVE '/usr/share/sounds/alsa/Noise.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Mono apl…

• 0

  Reputation Points

• 4 replies
• 5.3k views
• 2 followers

Werner

January 24, 20242 yr

I only have options 1,4,5,7 on my nand-sata-install utility and can only boot from a single armbian microsd card but no other. /dev/mtdblock0 shows no files. Everything has been fine till now! Would love some help. Thanks

• 0

  Reputation Points

• 1 reply
• 1.7k views

Werner

January 24, 20242 yr

Members, I have a question, because I can't find any documentation about what is broken or not. Why does /dev/rga not exist in my armbian install? I need it for my FFmpeg rkmpp config.

• 0

  Reputation Points

• 3 replies
• 3.3k views

lanefu

January 24, 20242 yr

i am taping in the dark here and in need of some help. i am running openhab on armbian 23.8.1 server and i need to get audio out on 3.5 jack for alerts. openhab has only two options system speaker and web audio. web audio plays on client like browsers using pulse audio. But if i use system speaker nothing comes out. What can i do to get sound on 3.5mm out on opi? is it even possible? i have this but this is also where my knowlege ends so help needed. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: rockchipdp0 [rockchip-dp0], device 0: rockchip-dp0 spdif-hifi-0 [rockchip-dp0 spdif-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card…

• 0

  Reputation Points

• 2 replies
• 3.1k views

Dim3nt0

January 23, 20242 yr

Good day, I have Opi 5 and bought this display https://www.aliexpress.com/item/1005005641383181.html?src=google&aff_fcid=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&aff_fsk=UneMJZVf&aff_platform=aaf&sk=UneMJZVf&aff_trace_key=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&terminal_id=b834b596955b44a1bf643629f5ba5647&afSmartRedirect=y . It was a blind buy ... And now I can't get it work if its even possible. I'm its my first time trying to get display on these boards usually use them trought Monitor or TV and it works flawlessly. Cant find even config.txt . But now im lost at how to get …

• 0

  Reputation Points

• 2 replies
• 2.3k views

ower

January 21, 20242 yr

Hello, I'm trying to install the zfs-dkms package with the latest build (Armbian_23.02.0-trunk.0127_Orangepi5_jammy_legacy_5.10.110_xfce_desktop.img.xz) and I get the following error: configure: error: *** This kernel does not include the required loadable module *** support! *** *** To build OpenZFS as a loadable Linux kernel module *** enable loadable module support by setting *** `CONFIG_MODULES=y` in the kernel configuration and run *** `make modules_prepare` in the Linux source tree. *** *** If you don't intend to enable loadable kernel module *** support, please com…

• 1

  Reputation Points

• 14 replies
• 10k views
• 2 followers

simonswine

January 21, 20242 yr

and, BTW, this will probably work on any SBC that has pwm and working port of wiringPi (wiringOP is much simpler than the dtbo method, IMO) WHY: I don't like fans that run full speed ALL the time pwm fans are a bit limited on the ground in small size, and expensive The SBC has pwm pins, so why not use them none of the examples I have found are adequate, either gpio off/full or excessive python scripts, 40 lines or more,, the bash script is ~ 10 lines Some of the wiringOP/gpio packages don't work (ubuntu-full desktop) try the commands in rc.local, if they don't work, then,,, dpkg -l |grep wiring; apt remove ..... git clone https://github.com/orangepi-x…

• 0

  Reputation Points

• 0 replies
• 3.4k views

wdtz

January 18, 20242 yr

When executing a command - sudo opt upgrade - returns an error: Setting up linux-image-legacy-rk35xx (23.11.1) ... Armbian 'linux-image-legacy-rk35xx' for '5.10.160-legacy-rk35xx': 'postinst' sta rting. * dkms: running auto installation service for kernel 5.10.160-legacy-rk35xx [ OK ] update-initramfs: Generating /boot/initrd.img-5.10.160-legacy-rk35xx W: Possible missing firmware /lib/firmware/rtl_nic/rtl8125a-3.fw for module r816 9 W: Possible missing firmware /lib/firmware/rtl_nic/rtl8107e-2.fw for module r816 9 W: Possible missing firmware /lib/firmware/rtl_nic/rtl…

• 0

  Reputation Points

• 2 replies
• 2k views
• 1 follower

MakKou86

January 17, 20242 yr

!!! Warning !!!: Think twice before you upgrade kernel on your PineBook Pro. After years unfortunately I decided to unlock upgrades Armbian Kernels and upgraded kernel to the newest one (current) - 5.15.93. After reboot Armbian couldn't find my encrypted root disk and booting ended every time in (initramfs). I installed again kernel 5.10.60 #21.08.1 and Armbian finds my encrypted disk again. Of course still there is no information that I have to enter the password to unlock disk but only black screen. Happily I know that I have to enter the password when the screen is black. Every upgrade of Armbian is connected with a dose of stress that I'll have to …

• 0

  Reputation Points

• 1 reply
• 2.4k views

Igor

January 16, 20242 yr

to recap: Tinkerboard (rev 1?) has 2 USB devices (from RK3288's internal ports), one for the Realtek HD audio, and one for the 4 USB ports (Genesys 4-port USB hub). while i have no info for the HD audio, the hub is powered via the 5V lines (noted as V5 pin in the datasheet). my mistake would be not checking if all the 5V power lines are shorted, or it's just connected to the hub. there's an option to NC the pin if using an external regulator (say, the RK808 power management chip?) The LAN is separated to the hub and instead directly connected to the RK3288 At least the datasheet for RK3288 says. no pinouts whatsoever so i think …

• 0

  Reputation Points

• 5 replies
• 4k views

Ikesankom

January 14, 20242 yr

Hello, sorry if this has been answered somewhere else. I was just wondering how i upgrade my Orange Pi 5 running Arbmian 23.11.1 Bookworm w/ Linux 5.10.160-legacy-rk35xx to the latest Kernel. I tried using `sudo armbian-config` and updating via that with kernel upgrades unfrozen but it doesn't seem to work. Is there something I'm missing? Startup splash below: ___ ____ _ ____ / _ \| _ \(_) | ___| | | | | |_) | | |___ \ | |_| | __/| | ___) | \___/|_| |_| |____/ Welcome to Armbian 23.11.1 Bookworm with Linux 5.10.160-legacy-rk35xx System load: 4% Up time: 0 min Memory usage: 8% of 3.83G IP: …

• 0

  Reputation Points

• 6 replies
• 8k views
• 1 follower

Werner

January 13, 20242 yr

Hello , looking to upgrade from SBC Rock64 to RockPro64< however, on the homepage it is mentioned, that https://wiki.pine64.org/wiki/ROCKPro64_Software_Releases Since my Rock64 is running aready Linux kernel 4.4 and i am looking to upgrade, both from Rock64 and from SDcard to eMMC, my question, if this limitation still applies to RockPro64 with newer editions of Armbian, also since there is no mention of it on the official Armbian Page for RockPro64 https://www.armbian.com/rockpro64/ Thank you very much

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

prahal

January 12, 20242 yr

Hello. The official adapter does not work for my orange pi 5 plus. https://aliexpress.ru/item/1005005956334270.html?spm=a2g2w.orderdetail.0.0.4e224aa6r3APff&sku_id=12000035019805399 The problem is this. Wi-Fi works, you turn on bluetooth, bluetooth doesn’t work initially. After turning on bluetooth, Wi-Fi does not work and bluetooth does not work either. Realtek RTL8852BE-CG BE CPU work in all officials builds. Help me please

• 1

  Reputation Points

• 9 replies
• 11.3k views
• 3 followers

Werner

January 12, 20242 yr

This https://github.com/Joshua-Riek/ubuntu-rockchip/wiki/Orange-Pi-5 produces nearly 0 dropped frames at 4K 60fps on https://www.youtube.com/watch?v=LXb3EKWsInQ While latest Armbian_23.11.1_Orangepi5_jammy_legacy_5.10.160_gnome-amazingfated_desktop.img.xz and doing immediately after install, only these commands: sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia sudo apt update sudo apt dist-upgrade sudo apt install mali-g610-firmware rockchip-multimedia-config exactly like it says on https://www.armbian.com/orangepi-5/ and sudo reboot produces alot of dropped frames on same youtube …

• 0

  Reputation Points

• 4 replies
• 4.3k views
• 3 followers

BOFFBOY

January 11, 20242 yr

This image works OK, and we now have both a 6.7 kernel AND graphics. Minor issues: EzCast stupid windows Wifi adapter does not plug and play. The vertical USB port does not sense plugging in a device (Wifi) Good work, Gullik

• 1

  Reputation Points

• 15 replies
• 6.8k views

Gullik

January 9, 20242 yr

Have an incident where I tried installing a newer kernel in an nvme working setup and the device wont post. My original installation flash card is working but is giving me problems. So I got 2 others and attempted to boot new version of the image and Im getting no post. I was able to solve my original problem by installing a legacy version in flash and copying /boot over to nvme. I also attempted rebuilding the mme partitions with no success. But it seems that there is something not working right with kernel 6.7.

• 0

  Reputation Points

• 3 replies
• 3.2k views
• 1 follower

Werner

January 9, 20242 yr

pi@opi5:~/AoC-2023-cplusplus$ lscpu --all --extended CPU SOCKET CORE L1d:L1i:L2:L3 ONLINE MAXMHZ MINMHZ MHZ 0 0 0 0:0:0:0 yes 1800.0000 408.0000 1800.0000 1 0 1 1:1:1:0 yes 1800.0000 408.0000 1800.0000 2 0 2 2:2:2:0 yes 1800.0000 408.0000 1800.0000 3 0 3 3:3:3:0 yes 1800.0000 408.0000 1800.0000 4 0 0 4:4:4:0 yes 2256.0000 408.0000 2256.0000 5 0 1 5:5:5:0 yes 2256.0000 408.0000 2256.0000 6 1 2 6:6:6:0 yes 2304.0000 408.0000 2304.0000 7 1 3 7:7:7:0 yes 2304.0000 408.0000 2304.0000 Why the odd cortex a76 MAXMHZ …

• 0

  Reputation Points

• 4 replies
• 2.4k views

lurk101

January 8, 20242 yr

FYI. Searching some forums around the web, stumbled on a post that indicated the TU3 Nano would work on the OPi 5. I thought I would give it a try. It worked for me plugged it in reboot. Download speed topped out at 200mb on the usb3 (top plug) connected to 5Ghz wifi. Happy days. Running the Feb.27 stable version of Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110_gnome_desktop. TC

• 0

  Reputation Points

• 4 replies
• 3.8k views
• 2 followers

toocanad

January 3, 20242 yr

Hello people, Happily running Bookworm, because it was the mainstream download for OPI5 a few months ago, I now see that the main download for OPI is back to Jammy. Apart from hardware accceleration, Bookworm runs great for me. In fact HA is not crucial for my server usage, though it would be nice. Question: what is the reason the main OPI5 download is now back to Jammy in stead of Bookworm? And what would be the advantages of going back from Bookworm to Jammy? (Got the aluminium passively cooling case for the OPI5, so far it's been great, 10 minutes of stresstesting all 8 cores doesn't get above 70 degrees celsius. For reference my…

• 0

  Reputation Points

• 1 reply
• 1.7k views

Marc R

January 3, 20242 yr

I am using Wifi/BT USB dongle to connect network for Orange Pi 5. But it does not work with Armbian. It works smoothly with Orange Pi's Ubuntu and Debian distros. I just need to insert the dongle into USB 3 to work. Is there anything I can do to use the dongle with Armbian? My dongle is "USB WiFi Bluetooth Adapter Dual Band 2.4/5.8Ghz Wireless RTL8821CU Don-ig"; https://www.ebay.com.au/itm/404244701011

• 0

  Reputation Points

• 5 replies
• 5.6k views

oh122

January 3, 20242 yr

New OPI5+, unable to finish install because ethernet doesn't work. I haven't been able to figure it out and my searches turned up nothing. journalctl has the following messages: - hpptx phy lane locked! - rk_gmac-dwmac fe1c0000.ethernet error: no phy at addr -1 - stmmac_open: cannot attach to phy (error -19) I've checked power supply, cables, edited the interfaces file, and more , with no success. I have an Orange Pi 5 that I can swap as is in its place and everything works. Coupled with the fact that I couldn't find mention of the errors, I'm hoping that someone can help me before I give up and return the OPI5…

• 1

  Reputation Points

• 19 replies
• 10.6k views
• 1 follower

octal8

January 1, 20242 yr

Hi. I've got a ROC-RK3399-PC SBC with a JMB585 PCIe to SATA extension card. Unfortunately PCIe always doesn't work on boot, whether it is in u-boot or kernel, with `PCIe link training gen1 timeout` error. Just as the following log: However, after I manually run these commands, PCIe seems working. ```modprobe -r pcie_rockchip_host modprobe pcie_rockchip_host ``` Kernel log: Does anyone have any idea about what is going on? Thanks in advance.

• 0

  Reputation Points

• 9 replies
• 14.5k views
• 4 followers

Igor

December 19, 20232 yr

Hi, I've had my 5+ for a week now and tinker with it when I can. Some things I've noticed... Using Amrbian legacy 5.10 legacy.... the system draws about 2.2w idle using a USB meter and no peripherals attached. When using the trying the latest 24.2.0-trunk.79, the power draw increases to 3w idle. I also noted the LED flickers between green and red rather than blue and red with legacy. My guess is more peripherals are being enabled. When using legacy, the first time i run an apt-get update there are 39 'gets'. When I then added a launchpad ppa and run again I only get 6. Not sure why that is. I cannot get…

• 0

  Reputation Points

• 7 replies
• 6.2k views

Thewonderer

December 19, 20232 yr

Anyone tried installing Steam Link? There seems to be an image in Raspberry OS but I cannot find a deb image for aarch64. Official flatpack is x64 only...

• 1

  Reputation Points

• 10 replies
• 10.4k views
• 1 follower

OttawaHacker

December 14, 20232 yr

Hi, I'm pretty new to this forum may be I will ask some already answered questions, but here they are: I just had a new orangepi 5 plus card and I failed to use the "buses": - I2s: didn't find anywhere how to activate it (i'm trying a dac as a soundcard). Didn't find the hifiberry-dac overlay neither (ok maybe this one is just for raspberry). - spi: I plugged a simple mcp3008 to the spi pins but can't read anything on it (i have the /dev/spidev0.0/1 and /dev/spiddev4.0/1 devices). I think I respected the rights pins. - i2c: when I activate the overlays in armbianEnv.txt, I can see a lot of messages every seconds with dmesg about rk-hdmi. Ma…

• 1

  Reputation Points

• 15 replies
• 16k views

Igor

December 10, 20232 yr

Version 20230325-edge with kernel 6.2 (pancsf-midstream). With HDMI USB LAN support. https://disk.yandex.ru/d/Xt36QdVcxRdEDA

• 1

  Reputation Points

• 85 replies
• 54.1k views
• 4 followers

balbes150

December 9, 20232 yr

Hi, The release notes for Armbian 23.11 state, under Key Improvements in This Release, "Mainline Kernel for RK3588 with experimental HDMI support." I am currently running the default 5.10.160-legacy-rk35xx kernel If I wanted to switch to and try out the mainline kernel for RK3588 with experimental HDMI support, would I do something like this: sudo apt install linux-image-collabora-rockchip-rk3588 After testing, If I want to rollback to the default legacy kernel, what are the steps involved? Apologies if there are instructions elsewhere that cover this. Thanks in advance for any guidance.

• 1

  Reputation Points

• 4 replies
• 6.5k views
• 1 follower

adr3nal1n27

December 5, 20232 yr

hello , im a 0 in linux , i have orange 5 with mvme , i folowed how to for boot directly to mvme , the how to made me delete the spi flash. all was good, o5 boot on mvme succesfully but at each reboot , my hardware have new mac adress. any one can show me what to do step by step ? i used : Joshua-Riek/ubuntu-orange-pi5: Ubuntu 22.04 LTS for the Orange Pi5 ( desktop & serveur ) Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110.img.xz ubuntu serveur 23.04 ( 64 ) it's the same on all , boot one time i have mac adress , reboot = new mac adress i cant fix ip localy , so i think when i deleted spi flash , may be deleted…

• 0

  Reputation Points

• 13 replies
• 12.2k views
• 1 follower

Turbine

December 2, 20232 yr

My Orange Pi 5 appears to be completely dead. No lights turn on when the power is connected and the SD card is freshly imaged as well. This started happening when I connected a USB-C multi-port dongle with a connected PD power supply to it. Is it possible to revive this?

• 0

  Reputation Points

• 7 replies
• 8.7k views

Ravi Terala

November 27, 20232 yr

Hello folks, I happily run Armbian Jammy XFCE on my much beloved Meko box (with at least SOME hardware accel) and Bookworm on Orange Pi 5. Both run excellent, but Jammy/xfce is a bit more snappy. probably because of partly harware accell. On the Meko R3588 4Gb box I installed Docker, Portainer, MQTT server container, Home Assistant container. All is well. I operate my boxes via RealVNC, so that it also will work seemlessly when VPN is active. The containers are so extremely light that they hardly take a few percent CPU. Home Assistant container takes 0,5Gig or so, MQTT server takes 0.1Gig. My first encounter with docker is very positive! Next I will try to add open VPN an…

• 0

  Reputation Points

• 1 reply
• 3.9k views

royk

November 26, 20232 yr

I installed Armbian on my R4SE downloaded from https://redirect.armbian.com/nanopi-r4s/Bookworm_current_minimal Everything seems to work just fine, but I am missing my second network interface. Only the WAN interface is shown. Is there a software fix I can apply, or should it be fixed in the OS image? armbianmonitor -u output: https://paste.armbian.com/gipilapuve

• 0

  Reputation Points

• 2 replies
• 3.3k views
• 1 follower

Junkman

November 25, 20232 yr

I haven't touched my ROCKPro64 for quite a while. Pulled it out today and starting playing with it. I was getting 2 blinks of white LED, then a pause, then repeating. I thought it wasn't booting or something. After checking a whole bunch of things, including connecting a serial terminal, I finally realized I had a bad Ethernet cable (and this was why it was not showing up on my router). The board (and OS installed to eMMC) had been fine the whole time. Now, my understanding is that the LED behavior is particular to software (bootloader, I guess?). But FWIW, on a slightly older Armbian (21.02.3) at least, this appears to be default b…

• 0

  Reputation Points

• 1 reply
• 2.6k views
• 1 follower

Werner

November 23, 20232 yr

Hello all, I got a problem after new update of armbian firmware through your own module (script). The left USB port on pinebook pro has stoped working at all. Before that was occasionaly after 6 -7 boot ups only one time not working (it is used for mouse). Now after x rebooting it doesnt work at all. The right USB port works without problems. On the left, also USB flash drive doesn't work. No idea, what could it be? Before, as already said, it has worked in 90%. Before firmware upgrade.

• 0

  Reputation Points

• 6 replies
• 4.5k views

pinebookpro-owner

November 8, 20232 yr

I've noticed a funny thing on 23.11.0-trunk.244, trixie edge. If I use netplan to change the names of the network interfaces, they disappear on the next reboot - linux no longer detects them at all. dmesg will show: ``` rockchip-dw-pcie a40c00000.pcie: Phy link never came up rockchip-dw-pcie a41000000.pcie: Phy link never came up ``` The interfaces will disappear from lspci. Any hint on what's causing this?

• 0

  Reputation Points

• 1 reply
• 2.1k views
• 1 follower

Tony3

November 1, 20232 yr

I recently make functionning the I2C-0 port on odroid M1 (thanks to usual user) see topic [odroid m1 i2c not detecting external device]. But I have another problem the tty1 display on the oled screen when I disconnect the HDMI. Where can i disabled this ?

• 0

  Reputation Points

• 5 replies
• 4.1k views

Sebastien Motala

October 30, 20232 yr

This is my config : Odroid M1 (8G) with Armbian 6.6.0-rc6-edge-rk3568-odroid build myself. >root@yanas3:/dev# i2cdetect -l >i2c-3 i2c rk3x-i2c I2C adapter >i2c-6 i2c DesignWare HDMI I2C adapter >root@yanas3:/dev# i2cdetect -y 3 > 0 1 2 3 4 5 6 7 8 9 a b c d e f >00: -- -- -- -- -- -- -- -- >10: -- -- -- -- -- -- -- -- -- -- -- -- UU -- -- -- >20: UU -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- >30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- >40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- &…

• 0

  Reputation Points

• 9 replies
• 4.9k views

usual user

October 29, 20232 yr

Hi guys ! So far I tested building bullseye without luck and the bookworm release img Building bullseye and burn it to an sd card system will not boot even after pressing the RCY button. I've build today a new img and it boots bullseye but it freezes loading first boot With bookworm it does boot pressing the RCY button but the Boot from MTD flash and system to nvme seems broken if power off the board remove the sd card the system won't boot with or without sd card (If I boot it again using the RCY with the installer already configured on the sd card and use the command df the nvme disk is not present but it appears in the i…

• 0

  Reputation Points

• 8 replies
• 6.1k views

j0ta

October 29, 20232 yr

I couldn't ping the pi anymore so i hook it up to HDMI. There i see the initramfs prompt What's up with that guys?? When i type df i only see /dev /run Broken m.2 sata?

• 0

  Reputation Points

• 4 replies
• 7k views

royk

October 27, 20232 yr

The Libre Computer Renegade RK3328 has hardware AES support. Should it not be listed by `lsmod` if the module is activated? $ grep aes /proc/cpuinfo Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid $ lsmod | grep aes $ How can one verify that the AES chip is being utilized? I'm on the Armbian 22.11 Jammy release (Kernel 5.15.y, Release date: Nov 30, 2022).

• 0

  Reputation Points

• 3 replies
• 3.6k views
• 1 follower

MBC

October 26, 20232 yr

*UPDATED - The issue is the powered USB3 hub which is actually NOT USB3 as advertised and is instead USB2. Sorry to have wasted your time* Hi, I have a 1TB SATA SSD in a USB3 enclosure (that supports UASP) connected to a USB3 powered hub, which in turn connects to the Top USB3 port of an Orange Pi 5 4GB. Armbian (Debian Bookworm) is installed and running from a 128GB NVME drive plugged into the M2 slot of the Orange Pi 5. If I do an "lsusb -t" I get the output shown below. The SSD is Bus 02, Port 3, Dev 5 and is using the uas driver but is showing USB2 speed of 480M rather than USB3 speed of 5000M. I have also tried pluggi…

• 0

  Reputation Points

• 0 replies
• 1.9k views

adr3nal1n27

October 25, 20232 yr

I know for sure that booting from an sd card and then using dd to write the uncompressed image to the emmc device isn't what works. I'm talking about Armbian_22.02.1_Pinebook-pro_focal_current_5.15.25_xfce_desktop.img here. Because that essentially bricked my PBP. I have the little adapter to connect the emmc to a usd slot, and using balena etcher to write to that isn't it either. the uboot in that image prevents booting from sd automatically as well, and i didn't find any uboot documentation that made it clear how to manually boot from sd, though i did hook up a serial console. This is what it said. The LED never turned green, the display flashe…

• 1

  Reputation Points

• 32 replies
• 24.7k views
• 3 followers

kgb

October 22, 20232 yr

I thought I had read that someone had the T2U working out of the box. Well, it's mostly there. When I tried it, didn't work. Got message in dmesg that firmware file not found. Did a Google search and found that it came down to the mediatek firmware files needing to be in the /lib/firmware/mediatek directory but they are currently in the /lib/firmware directory. FYI, the /lib/firmware/mediatek directory already existed and did not need to be created. Also in the current Jammy Gnome desktop Armbian, the file that was being loaded, mt7610e.bin, was not there and only the backup file, mt7610u.bin, was there in the /lib/firmware directory. What I d…

• 0

  Reputation Points

• 1 reply
• 2.3k views

bexem74332

October 17, 20232 yr

I have add user dtbo with "armbian-add-overlay rk3308-w1-gpio.dts" but it's NOT work.Some message is shown as below: pi@Pi-S:/boot/overlay-user$ dmesg | grep gpio [ 0.063257] OF: /onewire@0: could not get #gpio-cells for /usb@ff400000 [ 0.096538] rockchip-gpio ff220000.gpio: probed /pinctrl/gpio@ff220000 [ 0.097838] rockchip-gpio ff230000.gpio: probed /pinctrl/gpio@ff230000 [ 0.099097] rockchip-gpio ff240000.gpio: probed /pinctrl/gpio@ff240000 [ 0.100300] rockchip-gpio ff250000.gpio: probed /pinctrl/gpio@ff250000 [ 0.101462] rockchip-gpio ff260000.gpio: probed /pinctrl/gpio@ff260000 [ 8.818566] gpio-17 (onewire@0): enforced open dra…

• 1

  Reputation Points

• 3 replies
• 3.5k views
• 1 follower

solaris3308

October 16, 20232 yr

I'm trying to use an SPI driven TFT display on the orange pi 5, but I'm stuck on enabling SPI in the first place. Looking at the pinout of the orange pi 5 in its manual, it appears that SPI4...M0 is the only bus broken out to the pins. However, enabling "rk3588-spi4-m0-cs1-spidev" in the armbian-config menu does not seem to do anything, as no /dev/spi device exists after a reboot. Enabling any of the other spi hardware functions seems to work just fine, creating a /dev/spi device as expected, but none of the other spi busses are accessible through the pin header. I'm on Armbian 23.8.1 (image: Armbian_23.8.1_Orangepi5_bookworm_legacy_5.10.160.img). Has anyone used SPI on t…

• 1

  Reputation Points

• 3 replies
• 6.6k views
• 1 follower

Josh Blackburn

October 15, 20232 yr

Hi everyone, Has anyone been able to get gpu hardware acceleration to do encoding/decoding on Jellyfin on the orange pi 5? Thank you

• 1

  Reputation Points

• 1 reply
• 4.2k views
• 1 follower

royk

October 15, 20232 yr

Hi everyone! I have recently bought an Orange Pi 5 Plus (16 GB RAM) and installed Armbian (the Pi Plus version). Then I enabled GPU hardware acceleration, as suggested on the Armbian download page, which then updated chromium and other things to the rkmpp versions. Now, if I start chromium under Wayland (tried Sway, Gnome, and KDE), the hardware acceleration works nicely, so I get good FPS on e.g. WebGL aquarium, and similar things. However, the antialiasing of some items on the screen does not seem to be working. Antialiasing in WebGL seems off as well. You can see an example in the attached screenshot. Here's what I have tried so far: Before installing GP…

• 0

  Reputation Points

• 0 replies
• 2.7k views
• 1 follower

Ivgal

October 14, 20232 yr

Hello. I'm sure this has been discussed a lot but I couldn't find anything recent. I just got my Orange Pi 5 Plus and I installed Armbian 23.8 Bookworm CLI on it. It is really fast and I love it so far. I see that it is unclear whether we have some kind of working vulkan drivers or not but I just installed the mesa-vulkan-drivers package and the vulkaninfo command is actually returning output so does that mean that we have vulkan drivers that work for the G610? Thanks in advance

• 0

  Reputation Points

• 1 reply
• 4.4k views
• 1 follower

m33ts4k0z

October 13, 20232 yr

Hi. I am using Khadas Edge 2 Rockchip RK3588S with Armbian Minimal version. I have installed xorg and firefox browser. After "startx" I rotated display (xrandr -o left) and run firefox. I don't know how is it calls, but I get a big gap when scrolling the website. In xrandr -o normal, it's gone. I will attach the video. Help me please. Thanks. IMG_0085.mp4

• 0

  Reputation Points

• 3 replies
• 3k views
• 1 follower

Ilya

October 12, 20233 yr

Since I re-installed 23.8 Jammy with the extra ppa:liujianfeng1994 repo - I haven't been able to play any videos on my OPI5. All players I tried seem to have kernel issues decoding any h264. I've narrowed down the error message to a 4Gb memory limit with the selected version of the drivers but I was wondering if anyone had luck with playback. I had better luck with Jammy 23.4 and I regret upgrading. What is the recommendation? Should I try nightly with 6.6.0-rc1 kernel? I assume this one doesn't need panfork drivers anymore or are there other recommendations for h264 playback?

• 1

  Reputation Points

• 9 replies
• 4.5k views
• 1 follower

OttawaHacker

October 12, 20233 yr

Running Armbian 23.8.1 Jammy CLI Minimal. Since my kernel updated to 6.1 I have been having serious stability issues. Uptime is somewhere between 3 and 24 hours before the system becomes completely unresponsive. Prior to the 6.1 update this system was rock solid and would be up for months at a time, only ever rebooted for kernel updates. I currently have a monitor plugged in running dmesg -W hoping for something when these hard locks are occurring but I am not seeing anything to indicate what the issue may be. armbianmonitor-u output is: https://pastebin.com/DeU8VsB4 Any suggestions on any additional debugging I can enable to tr…

• 0

  Reputation Points

• 0 replies
• 2.4k views

Varimir

October 10, 20233 yr

Hello everyone, I have a problem with my NanoPi R4S. The WAN (eth0) port does not work well when it is configured to work on 1Gbps/Full. When this setting is active there is about 15% packet loss, which is quite annoying. In my tests I have already been able to identify that if I configure the port to work at 100Mbps/Full everything works normally. So I found the forum-post below, that explain that some u-Boot version wasn't setting the correct clock configuration for the netwok device at boot time, but now I have installed the linux-u-boot-nanopi-r4s-edge 22.08.6 and linux-image-edge-rockchip64 22.08.8 but the problem still there. I…

• 1

  Reputation Points

• 6 replies
• 7.7k views
• 1 follower

Pedro Lucas

October 8, 20233 yr

Hello, I have Rock Pi S V13 and Armbian 23.8.1 Bookworm with Linux 6.1.50-current-rockchip64. When I change CPU settings (min frequency, max frequency, scaling governor) using armbian-config, the change works correctly as expected. However, these settings are lost on reboot. When I check the status of cpufrequtils service, it seems that it does not load correctly as it is not able to find the requested governor: But if I start it manually later, it seems to load all my settings correctly: Any ideas to fix the problem except manually reloading it later? armbianmonitor: https://paste.armbian.com/owoluf…

• 0

  Reputation Points

• 4 replies
• 6k views

kolsi

October 6, 20233 yr

Hello, I cloned the master branch of WiringOP one month ago, it reported same version 2.46 and it was working except for the option to activate internal pull up/down. Trying it in C code using: pullUpDnControl(n, PUD_DOWN); or by terminal with: gpio mode 1 down same behavior, nothing happen.. by default, unfortunately in my case, it seem active a pull up resistor for all inputs. I searched on the web and found there was a bug, fixed. I checked again the main branch and in effect it is different now, the new code is: *(gpio + GPPUD) = pud & 3 ; delayMicroseconds (5) ; *(gpio + gpioToPUDCLK [pin]) = 1 <&…

• 0

  Reputation Points

• 2 replies
• 2.6k views

SergioAiello

October 6, 20233 yr

Per Radxa here, it is possible to obtain CPU temperature via "sudo cat /sys/class/thermal/thermal_zone0/temp". But the following paths do not exist on Armbian 23.05.1 Bookworm with Linux 6.1.30-rockchip64: /etc/armbianmonitor/datasources/soctemp /sys/devices/virtual/thermal/thermal_zone0/temp Running armbianmonitor -M, also does not show the temp: Time CPU load %cpu %sys %usr %nice %io %irq C.St. 22:29:52 408 MHz 0.02 0% 0% 0% 0% 0% 0% 0/6

• 0

  Reputation Points

• 5 replies
• 8.3k views

kolsi

October 6, 20233 yr

Hello! Does anyone, and by anyone I probably really mean @balbes150 :D, know what I need to do when building official Mesa for it to be recognized in the experimental 6.x kernel environment? There's a panfrost focused dev/staging branch that the panfrost devs are using that I would love to try and be able to build for OPi5 but when I do it I always just get llvm. balbes, you are managing to get the GPU recognized would you be able to share how that's done in the building? I'm not asking for you to provide a build I would just love to know how you do it so I can as well and test the new versions as they happen. This is the branch and commits…

• 0

  Reputation Points

• 5 replies
• 6.9k views

balbes150

October 6, 20233 yr

Looking for information on enabling 4 wire SPI on the Libre Renegade. I think have it enabled (spi-spidev) in armbian-config and I think configured correctly in /boot/armbianEnv.txt: param_spidev_spi_bus=0 param_spidev_spi_cs=0 param_spidev_max_freq=1000000 Connecting to pins GPIO pin# 19/21/23/24 I still do not see ANY devices matching /dev/spi* - An guidance as to WHY? I have the build framework, but am new to building armbian kernels but could navigate it with some direction. TIA folks! [Trying to connect a 240x320 LCD display using the ST7789-VW controller, not using Arduino IDE]

• 0

  Reputation Points

• 4 replies
• 4.6k views
• 1 follower

TonyMac32

October 3, 20233 yr

$ neofetch ubuntu@orangepi5 ---------------- █ █ █ █ █ █ █ █ █ █ █ OS: Armbian (23.11.0-trunk.145) aarch64 ███████████████████████ Host: Orange Pi 5 ▄▄██ ██▄▄ Kernel: 6.6.0-rc1-edge-rockchip-rk3588 ▄▄██ ███████████ ██▄▄ Uptime: 4 mins ▄▄██ ██ ██ ██▄▄ Packages: 427 (dpkg) ▄▄██ ██ ██ ██▄▄ Shell: bash 5.2.15 ▄▄██ ██ ██ ██▄▄ Terminal: /dev/pts/0 ▄▄██ █████████████ ██▄▄ CPU: (8) @ 1.800GHz ▄▄██ ██ ██ ██▄▄ Memory: 196MiB / 15718MiB ▄▄██ ██ ██ ██▄▄ ▄▄██ …

• 0

  Reputation Points

• 2 replies
• 2.6k views

Werner

October 2, 20233 yr

I download the following image and encountered serious problem; Armbian_23.8.1_Orangepi5_bookworm_legacy_5.10.160_cinnamon_desktop.img.xz The problem is that after screen blank out, 8 CPU cores get near full 100% usage and OPi5 gets very hot. They all have the following htop profile. Pri NI VIRT SHR S CPU% Command 20 0 5725M 224M R 96% cinnamon -- replace

• 0

  Reputation Points

• 0 replies
• 1.2k views

oh122

October 1, 20233 yr

The problem persist on both Armbian 23.8 bullseye and Armbian 23.11.0-trunk.107 Bullseye After change it via armbian-config It stays the default cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 1 2 3 CPUs which need to have their frequency coordinated by software: 0 1 2 3 maximum transition latency: 149 us. hardware limits: 408 MHz - 1.99 GHz available frequency steps: 408 MHz, 600 MHz, 816 MHz, 1.10 GHz, 1.42 GHz, 1.61 GHz, 1.80 GH…

• 0

  Reputation Points

• 2 replies
• 5.5k views

j0ta

September 28, 20233 yr

I have 23.8.1 Jammy installed with kernel 5.10.160 and I'm getting plenty of kernel errors during any video playback, and these also cause the playback to freeze. From my research, these error messages come from librga - which I assume come from the panfork and rockchip repos but I was wondering if anyone has been able to resolve these errors.

• 0

  Reputation Points

• 0 replies
• 3k views

OttawaHacker

September 22, 20233 yr

Standard install - Armbian Bookworm, full 'firmware install'. I am getting some packet loss over the LAN. A raspberry pi, Synology NAS and Deban x86 install on the same LAN do not seem to exhibit the same loss. Anyone have experience or ideas? Oddly enough this never seems to occur on fresh installs. This is a docker host for pihole and home assistance, no other packages are really installed at all. I've not really tried much, but since this is a standard install, apt-get update & upgrade are about the only modifications outside of docker install that has occurred. 1. This plugs directly in to a Ubiquiti switch 2. I have tried a few differ…

• 0

  Reputation Points

• 3 replies
• 2.6k views

royk

September 21, 20233 yr

Hello everyone, I recently installed my orangePi 5 to pass workload from my x86 servers over to the orangePi. My main focus is to reduce my overall energy consumption of my homelab. TL;DR Kernel thinks, that while being idle the sweet spot for the frequencies in "ondemand" and "schedutil" is: 1024MHz on the small chips (CPU0-3) 816MHZ on the big chips (CPU4+5, CPU6+7) Reason is an internal cost calculation power vs. frequency gain, which sorts out the lower frequencies. Long story: After getting my first orangePi5 in place, I started to play around with the hardware. I am running: █ █ █ █ █ █ █ █ █…

• 1

  Reputation Points

• 7 replies
• 9.1k views
• 1 follower

Matthias Strubel

September 20, 20233 yr