Amlogic meson

Hello, I try install armhf packets (piaware) from it's repo, what I do: dpkg --add-architecture armhf nano /etc/apt/sources.list.d/piaware.list change it to: deb [arch=armhf] http://flightaware.com/adsb/piaware/files/packages jessie piaware then apt-get update apt-get install piaware and have this error: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help…

Hi all, preparing an image for our next deployment (10 Odroid C2), I found that somehow the MAC address visible in Uboot doesn't make it into Armbian system. On the first copied system (I use odroidbackup.pl), in Uboot "Printenv" I get ethaddr=00:1e:06:36:58:63 Original system gives me: ethaddr=00:1e:06:34:fa:1a Both systems report to our DHCP server with the latter MAC, which will lead to troubles when both boards will be in the same network Any hints how to get the (apparently eFuse stored) MAC into the Armbian system? Thanks in advance, Michael

https://www.armbian.com/radxa-zero2/

Hi everyone, I have Radxa Zero 4GB-64GeMMC model. I'm using latest Armbian (22.05.3) on microSD card. I want to connect my portable SSD (500GB) to RZ with USB3.0 hub that has additional power imput to support energy hungry devices. I checked usb hub is working with 16GB usb flash. My ssd use realtek RTL9210 chip. I also get similar problem with 32gb mSD card formatted with FAT32. When I connected the SD card reader, other device that uses same hub become slaggish and do not working properly. If I unplag sd card or ssd everything back normal. I thing there is a driver problem. Radxa Zero Diagnostic Dump

Hello, I have 16GB orange eMMC v0.4 module for Odroid C2. I have installed on it Armbian Debian Stretch Next (mainline kernel). When I run iozone I got read results that is slower than eMMC Hardkernel specs. root@odroidc2:~# iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, …

Hi! I downloaded 'Armbian_5.20_Odroidc1_Debian_jessie_3.10.103.7z' today, put it on a SD card and successfully booted and 'ssh'ed in it. The board - an old C1 - is running fine. Now I want to install fail2ban and mc, but with the original 'sources.list' for apt there's no way to to that via apt-get. Will I run into difficulties if I change the 'sources.list' to the normal Debian ones and make my installations, updates and upgrades from there? Frank

Odroid C2: next and dev kernels do recognize USB hard-drives The stable kernel does. Kernel configuration issue?

Hi, I recently installed a fresh Armbian and did some tests. I noticed two major problems: Video is not accelerated: it is absolutely unusable with kodi Bluetooth seems absent (missing from DTB? other reason?) Please find below execution outputs of some commands: root@nanopik2-s905:~$ cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=nanopik2-s905 BOARD_NAME="NanoPi K2" BOARDFAMILY=meson-gxbb BUILD_REPOSITORY_URL=https://github.com/armbian/build BUILD_REPOSITORY_COMMIT=b9814056 DISTRIBUTION_CODENAME=focal DISTRIBUTION_STATUS=supported VERSION=20.11.3 LINUXFAMILY=meson64 BRANCH=current ARCH=arm64 IMAGE_TYPE=sta…

Hi, I've downloaded and successfully installed Armbian_5.47_Odroidc2_Debian_stretch_default_3.16.57 on an Odroid C2 (eMMC) : HDMI output is working fine. Then I ran: apt-get update then apt-get upgrade then I got a message saying that the kernel has been updated and that I need to reboot. After the reboot, I have no HDMI output anymore. SSH is available and board seems to be working fine. For information, after the update: uname -a Linux jeedom 3.16.57-odroidc2 #72 SMP PREEMPT Wed Sep 19 12:32:15 CEST 2018 aarch64 GNU/Linux Tried this without success. I've tested with other cable and screen, no success.

Hi There, i´ve tried armbian on my odroid C2, but the sources list is not fully available .. or simply wrong. an : apt-get update ... .... Hit http://httpredir.debian.orgjessie/non-free Sources Fetched 151 kB in 12s (12.3 kB/s) W: Failed to fetch http://apt.armbian.com/dists/jessie/InRelease Unable to find expected entry 'main/binary-arm64/Packages' in Release file (Wrong sources.list entry or malformed file) E: Some index files failed to download. They have been ignored, or old ones used instead. shows, that something is wrong with sources list... regards arel

Hi all, as a small status update on the seafloor business, here are some pictures of the new Odroid C2 based instruments which will be deployed in September/October in the northers Pacific. Ten modules with different functionality will be deployed, all based on a standard setup of Odroid C2, TRB3sc FPGA based TDC DAQ system, one PADIWA preamp, and a modded mdedia converter serving as a fully configurable mini switch. One of the modules carries several Hamamatsu mini spectrometers, as well as a camera, to observe bioluminescence. Another module is targeting at muon tracking with SiPM based readout: …

Hello, i bought my first odroid, and decide to install armbian. I download armbian from official server, and i try write os using rufus on Windows. I choose 'dd' and check raw file, rufus write image without error. When I plug MicroSDHC card, system starts, red led is on, blue flashing. From first minutes system have got big lag, I wait 50 minuts and do nothing in first boot. Last text on screen is **** Starting Update UTMP about System Runlevel Changes... [ OK ] Started LSB: PLEASE BE PATIENT AND DO NOT INTERRUPT THE FIRST REBOOT [ OK ] Started Update UTMP about System Runlevel Changes. *** I use Odroid c2 rev 2.0 20160226 and SanDisk ultimate Micr…

Hi, with my Odroid C2 I experience a strange behaviour regarding Armbian Updates. Initially Armbian_5.38_Odroidc2_Debian_jessie_default_3.14.79 was installed, after installation I did an upgrade to Debian Stretch. Meanwhile a new Armbian version v5.44 / v5.45 with a newer Kernel is available for Odroid C2 devices. If I do "apt update" and "apt upgrade", a newer version isn't visible or would be installed? The system is stuck on v5.38 with Kernel 3.14.79: " Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 3.14.79-odroidc2 Linux lx 3.14.79-odroidc2 #14 SMP PREEMPT Thu Jan 25 05:46:07 CET 2018 aarch64 System load: 0.39 0.28 0…

Hi, My first time attempting to use a nightly image in an attempt to get away from the legacy kernel. I installed Armbian_5.33.171007_Odroidc2_Debian_stretch_next_4.13.5.img on my C2, and it booted up just fine. Unfortunately, my primary use case for this hardware is a music streamer (and server), requires the ability to use Class 2 USB Audio, with (relatively) high-end USB DACs. I was unable to get the USB DAC to be recognized at all (did not show up in the ALSA devices listed by aplay -L, nor was it listed by lsusb.) I immediately reverted to the official Debian image running 3.14.79-odroidc2, and all was well again. As you can see below, my Te…

Anyone else having issues with reboot hanging on Xenial image on C2? Having to power cycle every time.

Hi, I just switch from hummingboard i4 to odroid c2 (same os, armbian, same app on it), all it's ok but I got an issue with load average, on i4 I have about 0.4 but on C2 I have 3 and I don't understand why. Here a vmstat from C2 : procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu----- r b swpd free buff cache si so bi bo in cs us sy id wa st 0 0 0 891036 74724 277404 0 0 0 0 310 493 3 2 95 0 0 1 0 0 891004 74724 277404 0 0 0 0 18272 1863 0 2 98 0 0 0 0 0 891036 74724 277404 0 0 0 0 18205 1950 4 0 96 0 0 1 0 0 891036 74724 2774…

What would cause the following dialog to show up when running a binary? : No such file or directory When I run strace against the file I get the following for the execution command. execve("./spyserver", ["./spyserver"], [/* 20 vars */]) = -1 ENOENT (No such file or directory)

Hello, i download wiringPi library using, # git clone https://github.com/hardkernel/wiringPi # cd wiringPi # ./build as root, i compile library with errors. login as: root root@192.168.2.110's password: ___ _ _ _ ____ ____ / _ \ __| |_ __ ___ (_) __| | / ___|___ \ | | | |/ _` | '__/ _ \| |/ _` | | | __) | | |_| | (_| | | | (_) | | (_| | | |___ / __/ \___/ \__,_|_| \___/|_|\__,_| \____|_____| Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.14.73-odroidc2 System load: 0.00 Up time: 44 min Memory usage: 7 % of 1719Mb IP: 192.168.2.110 CPU temp: 47°C Usage of /: 13% of 15G Last login: Wed J…

A few weeks ago, after a firmware-upgrade my C2 bricked. It's blue led didn't flash any more and no serial console was available. Since I had everything setup just right I wanted to recover it using these steps here: https://docs.armbian.com/User-Guide_Recovery/#replacing-boot Off course I replaced the packages with the ones for the C2. Specifically: https://mirrors.dotsrc.org/armbian-apt/pool/main/l/linux-5.9.14-meson64/linux-dtb-current-meson64_20.11.3_arm64.deb https://mirrors.dotsrc.org/armbian-apt/pool/main/l/linux-5.9.14-meson64/linux-image-current-meson64_20.11.3_arm64.deb https://mirrors.dotsrc.org/armbian-apt/pool/main/l/linux-bust…

Hello, I am using up to date Armbian Buster. TP-Link TL-WN722N V1 USB WiFi dongle causes system crashes after kernel upgrade to 5.4.12-meson64 #19.11.8 SMP PREEMPT Thu Jan 16 20:12:23 CET 2020 aarch64 GNU/Linux. Before updating the kernel, I had no such problem. Feb 12 20:17:15 xxx systemd[1]: Found device AR9271 802.11n. Feb 12 20:17:15 xxx systemd[1]: Started ifup for wlx54e6fc8d208e. Feb 12 20:17:15 xxx wpa_supplicant[2360]: Successfully initialized wpa_supplicant Feb 12 20:17:15 xxx sh[2344]: wlx54e6fc8d208e=wlx54e6fc8d208e Feb 12 20:17:17 xxx wpa_supplicant[2361]: Using interface wlx54e6fc8d208e with hwaddr 54:e6:fc:8d:20:8e and ssid "mynetwork" Fe…

Hi folks, I flashed the Armbian Jessie server image to sd. Then I ran update and upgrade after the system booted. I installed xorg and MATE desktop. No problems anywhere. I did not install a display manager as I want to login from tty. I basically performed the exact same install I have done for 15 years(since Gnome2). And a problem I haven't seen in 10 years or more rears it's ugly head as I type in "startx". MATE desktop boots up and I have no mouse or keyboard... I hit ctrl-alt-del and I have keyboard in the shutdown prompt. lsmod meson_ir 2943 0 joydev 10384 0 spidev 5785 0 spi_gpio …

I did a quick install of the desktop image for the ODROID C2. It sees no audio devices (HDMI - or any of the half dozen or so USB Audio devices I quickly tried). However, I have a app I wrote that builds a custom "kitchen sink" version of FFMPEG (everything is enabled). I built it on the C2 (to get a compile time), and noticed the sound did work from the app (and it sounded great). I wish I would have had more time to investigate why no audio devices are detected, and further, why I am able to play sound (only from the one app). Sorry. I am just trying to be helpful in saying "hey - the sound IS there - some users just may not be able to immediately get to…

Hi all at present state , i installed slim or gdm , but they are not good to start GUI automatically . so i start GUI by startx . what display manager is good for ondroid-c2 ? cat .xinitrc startxfce4 --- regards i write the install steps at http://odroid-akita.blogspot.jp/2016/04/odoroid-c2.html (japanese input is OK)

Hello, So I have ODROID C2 running latest Armbian bionic with kernel 5.6.11-meson64 #trunk.130. I have a Quectel E25 4G LTE modem connected via USB port. Everything works like a charm - BUT - whenever I try to download (or upload) even small amounts of data, I get kernel panic and the process hangs. Sometimes, the whole device crashes. It happens only when I try to download or upload data. Even trying to paste large amount of text into a terminal text editor causes kernel panic. This does NOT happen if I'm connected via ethernet. Here's the dmesg (while I was trying to wget a file) - [ 155…

Hi, I was using Hardkernel's provided image for Odroid C1 and that was working fine. There is bunch of test sensors attached to gpio, like DHT22, BMP085, DS18B20 and 433 mhz receiver. Now I have tried to switch to Armbian and all the sensors keep working as they did, except 433 mhz receiver The RFSniffer I use is this one: https://github.com/ninjablocks/433Utils I changed WiringPI PIN to be used to "5": --- a/RPi_utils/RFSniffer.cpp +++ b/RPi_utils/RFSniffer.cpp @@ -22,7 +22,7 @@ int main(int argc, char *argv[]) { // This pin is not the first pin on the RPi GPIO header! // Consult https://projects.drogon.net/raspberry-pi/wir…

I tried Armbian_20.11.0-trunk.32_Odroidc2_focal_current_5.9.8.img and Armbian_20.11.0-trunk.32_Odroidc2_buster_current_5.9.8.img and both will not boot after apt upgrade. Armbian_20.08.22_Odroidc2_focal_current_5.9.6.img will not come up after sudo reboot and has to be power cycled. I believe the latter has been a persistent issue.

Running ODroid HC4 on Armbian bookworm with Openmediavault 7 with docker compose plugin. I've done 2 clean installs to ensure the problem is reproducable and not something I meddled with. I spent time on Docker's forums running sample containers I was asked to try, they viewed my settings logs for docker and were at a loss. The containers go up fine and are running. They just cannot be accessed even from the host machine e.g. curl http://localhost:8080 fails when running a sample container docker hub forums supplied me with as a 'surefire' test. --- services: test_default_bridge: image: nginx:latest network_mode: bridge …

[ 0.206220] soc soc0: Amlogic Meson GXBB (S905) Revision 1f:0 (b:1) Detected [ 0.206304] of_clk_hw_onecell_get: invalid index 126 [ 0.206308] clk: couldn't get assigned clock 0 for /soc/aobus@c8100000/sys-ctrl@0/power-controller-vpu [ 0.206319] meson_gx_pwrc_vpu: probe of c8100000.sys-ctrl:power-controller-vpu failed with error -22 [ 0.279579] dwc2 c9000000.usb: c9000000.usb supply vusb_d not found, using dummy regulator [ 0.279624] dwc2 c9000000.usb: c9000000.usb supply vusb_a not found, using dummy regulator [ 0.280758] phy phy-c0000000.phy.0: USB ID detect failed! [ 0.280764] phy phy-c0000000.phy.0: phy poweron failed…

Hello, does anybody run above configuration successfully? If yes, what are the steps to make this happen? I did this: sudo apt install xorgxrdp xrdp But this is the result: xrdp (0.9.1-9+deb9u3) wird eingerichtet ... Generating 2048 bit rsa key... ssl_gen_key_xrdp1 ok saving to /etc/xrdp/rsakeys.ini Created symlink /etc/systemd/system/multi-user.target.wants/xrdp-sesman.service -> /lib/systemd/system/xrdp-sesman.service. Created symlink /etc/systemd/system/multi-user.target.wants/xrdp.service -> /lib/systemd/system/xrdp.service. A dependency job for xrdp.service failed. See 'journalctl -xe' for details. invoke-rc.d: initscript xrdp,…

I want tou share with you my experience with weston with mali wayland drivers https://forum.odroid.com/viewtopic.php?f=138&t=28426&start=50#p213474 Wish list: Can you guys add /lib/udev/rules.d/99-mali.rules KERNEL=="mali",SUBSYSTEM=="misc",MODE=="0777" to for all board with mali GPU And also set up directory and library cache for mali userspace drivers so all application will use mali version istead of mesa We still have problem with v-sync with amlogic DRM driver

Thanks to g4751 for doing the tests for Odroid-HC4. The tests for the Odroid-C2 were performed by myself. Tests were performed on Armbian 24.08 Official releases. Fix is to add a section to the DTB to enable a recently (last year) added kernel driver "meson64-reboot" that is an updated version of the "odroid-reboot" in older kernels. For Odroid-C2: - save your existing DTB - use DTC to convert DTB->DTS - modify the DTS with the code below - use DTC to convert DTS->DTB - reboot (will fail because new DTB not loaded yet) - POR (will now load the new DTB) - log-in - reboot should now work. …

Hi, I'm working on adding baudrate changes to recent Uboot v2017.11 for the Odroid C2. Took some time to understand the way Uboot handles access to hardware... I tried to get some clean solution, and wanted to ask on how I can submit my changes to the main developpers. Would be great if you could give me a hint on that issue. I still need some time for testing the changes, so it is not urgent (we need this feature to have 9600 8N1 access to the C2, as it will be deployed on a place without easy access So far, Michael

Hello, I just received my new Odroid HC4 and wanted to install Armbian on it. I downloaded and decided to use the following image: Armbian_24.2.1_Odroidxu4_jammy_current_6.1.77.img I used two ways to flash the SD card - Balnea echter and also - sudo dd if=Armbian_24.2.1_Odroidxu4_jammy_current_6.1.77.img of=/dev/mmcblk0 As recommended to bypass the bootloader petitboot I followed the recommended procedure: ********************************************************************** Bootloader Bypass Method This is now the preferred method. It is easier, and be performed without a display via SSH Install an SD Card with a fresh Armbian …

Hello, we are testing set of 50devices and on 20%-30% of them we are detecting errors, which seems as hardware issues with eMMC cards. Issues looks very similar to us. Example of device usage is: 1) device boots operating system (Armbian GNU/Linux kernel 3.14.79-odroidc2), 2) device works as expected for hours/days, 3) system logs starts containing emmc errors, 4) system freezes with console message: Message from syslogd@avast-hkc213254dfea768 at Feb 14 13:49:58 ... kernel:[189164.931207] Disabling IRQ #250 After consultation with Hardkernel we tried theirs ubuntu image and it looks better. After 4 hour test we do not detect broken card (test continues),…

So far I can only get the C4 to boot from a EMMC card, not a SDHC card, is that true or an I doing something wrong? I install the image with "dd if=./armbian...img bs=8M of=/dev/sde; sync; sync". That makes a bootable EMMC card, but all attempts with the SDHC card it just seems to sit there.

Hi everyone, thanks at first for all the efforts to maintain downloadable Armbian images. However, I am currently unable to execute a mainline Linux kernel, packaged as a .deb, that comes from the Armbian repositories. The current situation: Successfully tried Xenial default image (Kernel 3.14). Upgraded to next (Kernel 4.13.10.7), C2 board won't boot. Successfully tried Stretch next image (Kernel 4.13.5.7). Upgraded to next (Kernel 4.13.10.7), C2 board won't boot. Tried Stretch next nightly (Kernel 4.13.10.7), C2 board won't boot. Also tried the dev images from the beta repository, C2 board won't boot. (Besides I am aware of t…

hi all . i run odoroid-c2 foremaly i runed nginx with auth basic by next nginx.conf successfully in orange pi PC . nginx.conf is ------------- events { worker_connections 800; } http { include mime.types; default_type application/octet-stream; index index.html index.htm; keepalive_timeout 65; server_tokens off; server { listen 80; server_name localhost; #<-for test #root /var/www/d1; root /var/www/d2; } server { listen 80; server_name n------------n.dip.jp; root /var/www/d2; auth_basic "clos…

Can the c2 RTC be used with armbian?

Hello, I recently bought Odroid C2. Legacy Ubuntu Server image works great, but Ubuntu Server Next (mainline kernel) doesn't boot. SSH shows network error: connection timed out, screen is black. Is it something wrong with current image or my hardware? (Other OSes are working fine like legacy dekstop, DietPi). Power supply is official barrel DC jack 5V/2A.

Hi , i buiild a SPDIF connector like shown here: https://forum.odroid.com/viewtopic.php?t=21477 it uses the J7 SPDIF output which is connected to HDMI. On coreelec i can clearly see a HDMI soundcard output with aplay -L , i dont see that on armbian.... Is odroid c2 spdif output on armbian working ? why do i not see this soundcard that f.e. libreelec is showing ( i have 2 odroid c2s , one is running coreelec in my living room with HDMI connector working) im using a little older armbian distro since the latest has ethernet issues on C2 (im using 20.11 , kernel 5.9.10 debian edition ) regards, Simon

hi all, as mainline kernel options for Odroid-C2 are still not ready (USB not recognising DAC unless externall HDD connected during boot) .. have just switched back to 'default' build. I noticed system to be much slower then usual .... esp. when involving any writes. SD-Card is Sandisk 16GB and is working very well in OdroidXU4 and NanoPi NEO. When copying a few 100kB file takes few seconds: time cp /usr/bin/ssh ~/ ; time sync real 0m0.012s user 0m0.000s sys 0m0.010s real 0m2.982s user 0m0.000s sys 0m0.010s I tried with 'dd' command to see how fast simple writes are going and got at best 200kB/sec .... Does anyone have suggest…

Dear all, I have a strage problem here with handling large files and I ran out of ideas. System: Odroid C4 (running from SD-card) OS: 5.7.15-meson64 #20.08 SMP PREEMPT PRETTY_NAME="Debian GNU/Linux 10 (buster)" Attached to the system are a few USB disks: 3x 8TB, 1x 4TB, 1x 3TB, 1x 2TB All filesystems: ext4 (except the remote NAS filesystem, which is ZFS - see below) 3 of these disks are encrypted via truecrypt 7.1 On the 3 TB disk (ext4, unencrypted) there is a zipped dd-image of a harddisk. That file has about 760 GB size Now I tried to copy this file to a different location…

Today I installed packages (apt-get upgrade): armbian-config armbian-firmware linux-buster-root-current-odroidc2 linux-dtb-current-meson64 linux-image-current-meson64 linux-u-boot-odroidc2-current and rebooted the system. Afterwards no more USB devices were found: Active USB Hub, USB Hd, USB mouse, USB memorystick Regardless if connected via USB Hub or directly. lsusb doesn't show any devices. Any hints? Thanks in advance

Hi everyone, I've just installed Armbian on my Odroid C2 but I'm struggling running Iceweasel Firefox. I have a segfault everytime even in safemode, any guess of the problem (I made both apt-get update & apt-get upgrade). Thanks !

I’m running an Odroid C2 and trying to drive a 14.9" 1280x390 60hz LCD marquis display. On a Pi I can change the boot config files to the following and the display works like a champ. [HDMI:1] hdmi_group=2 hdmi_mode=87 hdmi_timings=1280 0 8 128 64 390 0 1 3 24 0 0 0 67 0 42009500 8 On the Odroid running Armbian 22.11 Jammy XFCE I tried changing: /boot/armbianEnv.txt adding display_autodetect=false hdmimode=1280x390p60hz I had no joy with this change, it did not modify the display output. I love how fast and light Odroid is with Armbian, it is really snappy, but I need some help stretchin…

Hi, I installed yesterday armbian on my Odroid C2. I would like to use an USB to serial converter but, the device is not detected by the system. When I plug the USB device, I just have this message in the kerner.log file and the USB device is not created : Nov 18 12:04:41 localhost kernel: [59003.780747] usb 1-1.3: new full-speed USB device number 13 using dwc_otg However, when I run lsusb the device is listed : root@odroidc2:~# lsusb Bus 001 Device 013: ID 1a86:7523 QinHeng Electronics HL-340 USB-Serial adapter Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID…

Hi, Having problems with instalation of certbot on latest armbian and Odroid C2...; root@odroidc2:/etc/apt# apt-get install certbot Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: certbot : Depends: python-certbot (= 0.8.1-2~bpo8+1) but it is not going to be installed E: Unable to correct…

I am trying to follow various tutorials on full disk LUKS root encryption for Odroid C2 with a emmc. Every tutorial I have found makes use of a separate partition for boot. Something like /dev/sdx1 (vfat) 100Mb. Mostly raspi tutorials but a few others that are step by step instructions out there as well. The armbian.img file does not have a separate boot partition when I use dd to transfer to emmc or sdcard. Do I just make a vfat partition on /dev/mmcblk0 (the emmc) and copy the /boot folder over to /dev/mmcblk0p1, and run dd again to put the arbian.img on /dev/mmcblk0p2? Anybody know of a what I need to do to make that partition so I can try some…

Hi, I have question about ports /dev/ttyAML1 and /dev/ttyAML2 (device Odroid C2, Image Buster) I dont see in dmesg the ports /dev/ttyAML1 and /dev/ttyAML2 [ 0.000256] printk: console [tty1] enabled [ 1.877506] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 13, base_baud = 1500000) is a meson_uart [ 1.877549] printk: console [ttyAML0] enabled [ 3.452296] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 3.455230] systemd[1]: Created slice system-getty.slice. [ 4.257715] cdc_acm 1-1.4:1.0: ttyACM0: USB ACM device overlays=i2cA i2cB uartA uartB uartC w1-gpio How should i chnage the meson-gxbb-…

I successfully flashed the "Armbian_24.11.1_Odroidc4_noble_current_6.6.60-kisak.img" on my emmc, and everything boots, runs, and updates fine... My 2TB USB3.0 seagate HD, /dev/sda, is seen fine in "dmesg", as well as "lsblk" and "blkid", but when I add my UUID, ..., in /etc/fstab it fails to mount at boot. see below line in /etc/fstab for above /dev/sda1 : UUID=<output-of-bklid-for-sda1> /media/USB01 ext4 defaults 0 1 To test the above /etc/fstab mount I ran: sudo findmnt --verify (which completes successfully) Also, if I run: sudo mount -a (it manually automounts /dev/sda1 -> /media/USB01 successfully). …

So as we know, the Hardkernel kernel did support powering the device on and off via a GPIO pin. This does not seem to work on Armbian with the mainline kernel. What does work is powering the device on and off with the remote control. So I wonder, what has to be done to enable power on and off vie the GPIO? My approach till now makes it possible to shutdown the device via GPIO interrupt. But then it will not come up again except if I reconnect the power cord or use the remote. I use this user device three overlay btw: /dts-v1/; /plugin/; /{ fragment@0 { target = <&ao_pinctrl>; __overlay__ { powe…

After the last "sudo apt upgrade" my odroid C4 (meson) doesn't reboot properly anymore. In the system out there are many lines like: "Begin: Running /scripts/local-block ... mdadm: No arrays found in config file or automatically done." and one : "mdadm: error opening /dev/md?*: No such file or directory mdadm: No arrays found in config file or automatically /scripts/local-block/mdadm: 58: /scripts/local-block/mdadm: rm: not found" at the end: "Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/mo…

Allcon, my pik2 constantly locks up. i havent been able to find anything that causes. going to cut this short before it locks up http://ix.io/1e4Q i have tried SD cards from san disk pny verbatim lexar: no change i have tried different power supplies. the barrel jack under vairous voltages: many different power supplies i cannot find any consistancy.

When I start the OS for the first time, the cursor is not visible, either at the command line or in the nano editor. I'm running the HDMI output through a HDMI->VGA adapter, which is then fed into my KVM along with the mouse and keyboard. The monitor is capable of 1920x1200, and it all works fine except for the cursor not being visible. I've tried various escape codes, etc. Nano never displays a cursor. When I log in via SSH the cursor is plainly visible. I'm trying to configure the WiFi, which doesn't seem to want to work if the ethernet is connected, so I'm stuck at the tty terminal. Any suggestions?

Hello, After installing Armbian 5.59 I have problems with sound. When I install the distribution with the 4.14.69 kernel, I have an intermittent sound. When with 4.18.7 sound is missing. How can I fix it? Is it possible to change the kernel? If so, please follow the instructions step by step. greetings trebor

I can't get the ubuntu gui desktop to use the entire 2160p screen - it only uses 1/4 (1080p upper left rectangle.) The settings menu for display is locked to 1080p. I've searched and there are explanations as to how to set boot.ini to get 2160p (which works) but the ubuntu desktop won't use the full screen. What do I need to do to get a full screen GUI display? Thanks.

Hi. I have experimented to make a csc for Khadas Vim2, similar to the one we already have for Vim1. It works pretty well. But I just wanted to check with the dev community before incorporating it to the build system, how do you guys feel about it.

Hello. I tested Armbian Jessie with Odroid C1+ and encountered several issues, would like to know if they're known or if I've done something wrong. 1) Odroid C1+ gets no display if not booting into X11. Framebuffer text console is not present at all. This makes it impossible to do any kind of configuration if not connecting via SSH. 2) If connecting via SSH, updating the system and rebooting, it doesn't seem to boot anymore. The machine is not available for ping, and I can no longer connect to do any further configuration. 3) Issuing "reboot" over SSH seems not to reboot the board, instead power needs to be cycled manually. I'm tried server and desk…

Hello, I freshly installed Armbian Buster 20.02.3 with 5.4.21-meson64 and also compiled Kodi 18.6 from source by following this guide. It seems however that I cannot get any HDMI sound and ALSA gives me: aplay: device_list:272: no soundcards found... Could it be that I am missing something fundamental or is this a known issue? Thank you. Manos

Hi I'm wondering why chromium is missing from the ODroid C2 image when taking the non-desktop image and then adding the necessary packages to get a minimal X working? Planning to just build it from source, but wondering why it was missing from the core armbian distro? Is there a reason?

I have a second usb network card (chip ax88179) conected to my C4. It randomly crashes and I have to rmmod/modprobe to make it work again : can't be done remotely without network... Looks like this kind of problem is kernel related : any idea ? uname -a Linux gwm 5.8.16-meson64 #20.08.14 SMP PREEMPT Tue Oct 20 22:50:41 CEST 2020 aarch64 GNU/Linux [34120.524606] ------------[ cut here ]------------ [34120.524659] NETDEV WATCHDOG: enx002427fe2bf8 (ax88179_178a): transmit queue 0 timed out [34120.525139] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:442 dev_watchdog+0x300/0x308 [34120.525160] Modules linked in: …

With my OPi Zero, I noticed that at random times the ethernet connection somehow gets disabled. The only way to recover is by power cycling. I use the device as Pi-Hole (so when ethernet gets disconnected, I don't have internet anymore), print server and UniFi controller. I decided to swap it for my Odroid C2. Odd enough the C2 has the same issue. Maybe someone can help me with this? When powercycled, the Odroid with the latest Armbian (installed two days ago) is all up and running fine. It can connect to the internet, I can SSH into it. The ethernet led is flashing orange, so the gigabit connection is available. However, at rondom times the ethernet led…

Hi armbian team ! I've been running my Odroid C2 for almost 2 years with the only then available distro for my board : odrobian. As that distro is now left without maintainer, I'm turning to other distros and am glad to see my board supported by armbian (which I currently use on various Orange Pi boards). Is there a path to migrate my Odroid C2 installation from odrobian to armbian with minimum downtime ? (it's a server) Or should I consider installing everything from scratch on another board and copy my configuration there ? Thanks !

Not sure if this belongs here or upstream but I figure I'd post here first. I'm running kubernetes on a bunch of odroid c2s and randomly pairs or sometimes single ones will crash randomly. I was able to capture the logs from the crash, but I can't seem to get a core dump. I was, however, able to determine that the panic occurs when rapidly removing and adding virtual ethernet devices. Some sort of collision seems to occur and the kernel oopsies into oblivion. It happens constantly, so much that I've had to put my project on hold =( This happens with the stock image from hardkernel, the latest stable armbian image for c2, and the latest nightly for …

Hi guys, I have issues with audio - only dummy interface shown - after the system update of ~2year old armbian. I did not find any solution, so I decided to go for latest build - so I flashed latest image Armbian 23.02 Jammy XFCE to the emmc drive of my odroid C4. System started ok, but unfortunately no HDMI audio device shown anyway. I have no idea what to do, my dmesq is full of these lines: [ 13.936415] fe.dai-link-0: ASoC: no backend DAIs enabled for fe.dai-link-0 [ 13.937748] fe.dai-link-0: ASoC: error at dpcm_fe_dai_prepare on fe.dai-link-0: -22 ... [ 935.795034] fe.dai-link-0: ASoC: no backend DAIs enabled for fe.dai-link-0 [ …

Hello Forum, i am using a vdr headless server with 3 Technisat Skystar USB tuners for satellite television streaming. Before i used a raspberry pi 2 but because of limitations with its ethernet bandwith i went to odroid c2. System is now armbian with self compiled vdr with vnsi plugin, both out of git repo. System runs fine but after some hours (8h) a sporadic failure occurs and (USB?) system becomes unusable, To get the 3 dvb-s2 tuners running i increased the urb pool (USB request block) with kernel parameter "coherent_pool=6M" in boot.ini. I calculated that every of all 3 instances of driver needs about 512kB of USB buffer memory, without the option the first inst…

my TFT shield need fb_odroidc_tft32 missed module from there ) https://github.com/longsleep/ubuntu-odroidc/blob/master/drivers/video/fbtft/fb_odroidc_tft32.c

Hi, I'm currently considering an ODROID C2 to replace an Rpi3 as a combined headless tvheadend and mysql server, with GPIO control of a relay for a fan. It's upgrading to Gigabit LAN that I'm after, to avoid the occasional bottleneck to my NAS. Legacy sounds like it's working well enough on the C2, but the USB T2 tuners I'm using are only supported in kernel 3.19 or above... The C2 page suggests only legacy is available, but the package repository page suggests otherwise: linux-image-odroidc2 3.14.79 Amlogic S905 Hardkernel Odroid C2 linux-image-next-odroidc2 4.13.3 Amlogic S905 (meson64) Hardkernel Odroid C2 …

Hello, I have trouble activating i2c on odroid c4. There's a pcf8563 module connected to the board. Also, /dev/i2c-0 /dev/i2c-1 exist. But pcf8563 does not show up when I run i2cdetect. I can rule out hardware issue because both i2c and pcf8563 work well with Hardkernel's Ubuntu image. So far, I've tried the followings but they don't work: Adding overlay="i2cA i2cB" to /boot/armbianEnv.txt and reboot. Manually editing device tree by changing status under "i2c@1d000" to "okay" and reboot. Also, I remember that i2c used to work on older versions of Armbian, which come with older version of kernels. But since linux 5.19, i2c no longer w…

I'm currently running Armbian 5.60 on an Odroid C2. Tried the new mainline kernel version (5.71) on the weekend and everything looked fine at first, but when I got to starting one of my docker containers, it failed. This container uses armhf binaries. Is there some way of enabling armhf support with the new mainline kernel builds of Armbian, or do I need a custom build now? I installed docker via armbian-config. As far as I can remember, I did not have to do anything special to get this working on the 3.x kernel build... Any pointers in the right direction would be appreciated. Thanks and best regards, Ulr…

It seems the Armbian test image for the NanoPi-K2 only works on an SD card. At least mine doesn't seem to boot when I put it on the 8GB eMMC module. Is there an eMMC armbian image for the NanoPi-K2 or is there something I need to do to get the existing image to boot on the eMMC module?

hi all . i think sd card is much shorter life time and restricted size ( 64G ~ 128G and big size is too expensive ). so as server , i like to use hard disk as root . for this purpose , nand-sata-install.sh is excellent ( but too complex for me to understand ) . i use nand-sata-install.sh on odroid-c2 armbian . and on working armbian , i run next script . ( the timing to attach sdb is about 10~15 second later after armbian booting ) . sda1 is cloned to sdb1 . clone-rsync-2-HDD-delete.bat ntpd -s date echo '--------------------' umount /mb1 mount /dev/sdb1 /mb1 df echo '--------------------' read X echo $X cd /mb1 mkdir -p bin etc home lib …

What's happen with my nano pi k2 just boot up and stop here. GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:AA;SD:0;READ:0;0.0;CHK:0; no sdio debug board detected TE: 194208 BL2 Built : 13:48:56, Sep 23 2016. gxl g7459bd4 - jianxin.pan@droid06 set vcck to 1120 mv set vddee to 1000 mv Board ID = 6 CPU clk: 1200MHz DQS-corr enabled DDR scramble enabled DDR3 chl: Rank0+1 @ 792MHz - PASS Rank0: 1024MB(auto)-2T-11 Rank1: 1024MB(auto)-2T-11 DataBus test pass! AddrBus test pass! Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000 New fip structure! Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600 Loa…

Hi, i had a little problem with root login on C2. It gives a message about "/usr/local/bin/temper" file absent and goes to restart. Problem solved by installation "armhf" architecture (temper file is present but compiled for 32 bit). thank you very much for your work.

It seems the networking in Armbian 5.59 is messed up. It creates a eth0 adapter (disabled) and Wired network 1 adapter. You can delete these in nmtui, but they always return. I had the same issue with NanoPi Duo using mainline Stable. I can get it to work a bit using armbian-config, removing all interfaces and configuring IP, but it gets screwed up again. I cannot trust to run 5.59 headless because I have no way to get into the SBC without hooking video back up.

Hello, After upgrade Armbian (4.19.69-meson64) to Armbian Buster with Linux 5.3.11-meson64 warning messages shows up on boot in dmesg: ... [ 1.973932] Key type encrypted registered [ 1.985109] dwc2 c9000000.usb: c9000000.usb supply vusb_d not found, using dummy regulator [ 1.985153] dwc2 c9000000.usb: c9000000.usb supply vusb_a not found, using dummy regulator [ 1.986616] phy phy-c0000000.phy.0: USB ID detect failed! [ 1.986623] phy phy-c0000000.phy.0: phy poweron failed --> -22 [ 1.986643] ------------[ cut here ]------------ [ 1.986700] WARNING: CPU: 3 PID: 68 at drivers/regulator/core.c:2036 _regulator_put+0x34/0xd8 [ 1.986702] Modul…

I'm running Armbian from a emmc 16GB card. When I use the web browser the mouse constantly flickers, is there any way to get this to stop? Is there a graphics driver I should have enabled? When I select Additional Hardware Drivers none show up, so maybe there isnt a GPU accelerated driver available. Also switching between desktops feels sluggish. Maybe Im expecting too much performance from a $50 SBC. Thanks for your help & time in making this distribution. Im just looking to make the best user experience possible.

I have a 4-port USB 2.0 hub powered by a 5V 3.1A power supply that does not show up on my C2, with or without devices connected to it. I have the C2's USB OTG port disabled as I use a DC power supply. $ sudo lsusb Bus 001 Device 004: ID 1df7:3010 Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. 4-port hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub dmesg does not log the hub connecting/disconnecting. How do I troubleshoot this? armbianmonitor -u: http://ix.io/1DzS

lm-sensors can read temps fine - $ uname -a Linux Odroid-C2 4.19.20-meson64 #5.75 SMP PREEMPT Fri Feb 8 10:08:40 CET 2019 aarch64 GNU/Linux $ sensors -u scpi_sensors-isa-0000 Adapter: ISA adapter aml_thermal: temp1_input: 39.000 But htop displays 0 C -

Images tried : Armbian_21.02.1_Odroidc1_bullseye_current_5.10.12.img.xz Armbian_22.08.0-trunk_Odroidc1_jammy_current_5.18.19.img.xz Results: Armbian_21.02.1_Odroidc1_bullseye_current_5.10.12.img.xz Network is recognized and ssh login possible + Serial console output working. ping gmail.com is working Armbian_22.08.0-trunk_Odroidc1_jammy_current_5.18.19.img.xz Network is not recognized and ssh login possible + Serial console output working. ping gmail.com is not working

I have an C2 and an old VU7 (800x480p60hz) https://wiki.odroid.com/accessory/display/vu_series/vu7/vu7#tab__odroid-c2 that I was hoping to use for a mini kiosk. Was able to run the older Hard Kernel supplied images with the uboot boot.ini updates suggested above to change disable auto detect, fix the resolution, and set to DVI rather than HDMI mode. When I loaded the latest Focal image from Armbian when I have the screen switched on then the kernel faults and reboots. ## Flattened Device Tree blob at 04080000 Booting using the fdt blob at 0x4080000 Loading Ramdisk to 7b06a000, end 7bf49d63 ... OK Loading Device Tree to 000000007a…

Hi I build ubuntu xenial with next kernel (4.13.....) and image don't boot https://pastebin.com/QHQfHHSa and I also can't boot debian 9 with next kernel https://pastebin.com/yXjWk5Wh Any idea where is problem?? all fine with dev kernels

Hi! I have buy an used odroid c2 and want to connect it to my tv. I have tried latest desktop image but my tv won't show me nothing so i tried latest Focal Cinnamon image and it is the same. I can log with ssl Here is my arbianmonitor -u result http://ix.io/3ZCA

Hi all, I have some piece of software to compile on our Armbina system (Linux odroidc2 4.19.90-meson64 #5.99 SMP PREEMPT Fri Dec 20 13:47:25 CET 2019 aarch64 GNU/Linux). It is a C++ program, usually running on x86 machines, and has one line of code killing the compilation: asm volatile ("rdtsc" : "=a" (low), "=d" (high)); I need to replace it by some code working with g++ on ARM64. Anyone how can give me a hint? I tried Google, but found no reasonable solution. In case, the software package is public, if you need the link to get it, please let me know. Any help is appreciated. Thanks in advance, Michael

v-sync is it working or not? I just start up debian xenial x.org with meson drm driver, but it looks like v-sync don't work. Should I change something in x config ? amlogic drivers has always problem problem with v-sync only video decoder pipeline( amlogic magic idea how to do video decoding) is sync-ed properly I opened terminal and I moved it down and can see window from prev. frame so v-sync don't work

Please delete! I just found the problem. __________________________________________________________________________________________________________________________________________ Hi guys, i'm running an Odroid C4 with Armbian Jammy. uname -a Linux Homeserver 6.0.13-meson64 #22.11.2 SMP PREEMPT Sun Dec 18 16:52:19 CET 2022 aarch64 aarch64 aarch64 GNU/Linux Everything works fine so far. Today I just bought an external ssd drive "SanDisk Portable SSD 1TB". I can mount and use it, but the speed seams quit slow to me. The packaging of the ssd say "up to 520MB/s" and the USB 3.0 ports should have higher speed than this: …

Hello, A GPS module ublox is connected to a odroid c2 board on GPIOX.12 and GPIOX.13 for the RX and TX and GPIOX.10 for the PPS. The board is running the stable kernel 4.19.42-meson64 from Armbian based on Debian stretch which was dist-upgraded to Debian buster. I am trying to get the /dev/pps0 entry using GPIOX.10 to finish the chrony setup but I cannot find the correct syntax in the DTS file. Any pointer or idea ? I try either of the gpios line below, none of them seems to be correct. pps { gpios = "< 0x1e 0x66 0x0 >"; #gpios = "<&gpiox 10 GPIO_ACTIVE_HIGH>"; #gpios = "< 0x66 >"; assert-fall…

After some hours of compiling I got OpenCV 4.1.1 running on Armbian Buster 64-bit. The SBC is an Odroid-C2. Thank you for this great OS-image.

Hi, I would like to run a 32 bits (armhf) Debian or Ubuntu image on an Odroid C4. Do you know if this is possible, and if it is, can you point me to the right image ? Cheers, jf

Hi, I'm getting a random packet loss on the ethernet connection. When pinging, about 6-8% pings are lost, the ssh connection sometimes freezes for a moment. Things I've tried so far: Disabled NetworkManager, added eth0 in /etc/network/interfaces with a static ip4 address Disabled EEE for eth0 Replaced ethernet cable Plugged into different switch None of them made something better. My C1 & C4 with the same Armbian Buster version/release don't have this issue. How to investigate deeper in this issue?

Greetings all. Today I tried updating my Odroid C2 to image 5.22 posted on Oct 22, 2016. And I got the following error during apt-get upgrade: Setting up linux-u-boot-odroidc2-default (5.22) ... /var/lib/dpkg/info/linux-u-boot-odroidc2-default.postinst: line 5: conditional binary operator expected /var/lib/dpkg/info/linux-u-boot-odroidc2-default.postinst: line 5: syntax error near `function' /var/lib/dpkg/info/linux-u-boot-odroidc2-default.postinst: line 5: `[[ == function ]] && setup_write_uboot_platform' I peaked at the code in /var/lib/dpkg/info/linux-u-boot-odroidc2-default.postinst contains #!/bin/bash source /usr/lib/u-boot/platform_install.sh [[…

Hello Armbian Community, I'm reaching out for help with a critical issue I've been facing on my ODROID HC4 server since updating to Armbian_community 24.8.0-trunk.4xx. I put 4xx because I don't know which version caused the issues. It was yesterday and I just saw updates in my OMV workbench, did the updates and then rebooted and then was unable to access OMV anymore. I have since upgraded to trunk.500 last night, didn't help, and trunk.501 this morning also didn't fix anything. Here’s a detailed account of the situation and the troubleshooting steps I've taken so far. Background: Device: ODROID HC4 OS: Armbian (l…

Hi guys, I just recompiled my patches from old 2015 Uboot to the 2018 version, allowing setting the baud rate in Uboot (for accessing it by 9600 8N1), and saving envs in eMMC. First one works, I can switch easily baudrates now, but "saveenv" fails, spitting out a lot of error messages: => saveenv Saving Environment to EXT4... Card did not respond to voltage select! ** Bad device mmc 0 ** Failed (1) I also see that apparently the settings are being loaded from a wrong partition: U-Boot 2018.07-armbian (Oct 28 2018 - 10:43:58 +0100) odroid-c2 DRAM: 2 GiB MMC: mmc@72000: 0, mmc@74000: 1 Loading Environment from EXT4... Card di…

On the odroid c2 server I want to install jwm with xorg. What packages are needed for xorg? The log complains that it cannot find fbdev.

Hi all, I'm new to Linux and trying to set up a music server using my Odroid C2/Armbian/Cantata/MPD/HDMI sound. Got Armbian 5.60 (Stretch) 4.18.8 installed. Cantata sees the small test music library I set up on the C2 and appears to play tracks as the progress bar moves. I get no sound from the C2 connected HDMI monitor. (for initial testing only, i2s + DAC/Amp later). I tried the same set up using the Odroid Ubuntu/Mate desktop image a few days back and it worked straight out of the box. My suspicion is that the audio output settings in the mpd.conf are not correct (mpd 0.19.21). For HDMI sound output, does my version of Armbian use Pul…

Hello Guys, i am running an Odroid C2 with the latest Armbian based on debian Bullseye. As disk i am using an 8GB emmc flash drive. For longlive reasons i am thinking about to reduce the read or more important the write access to that drive. I know, that every SD card and also every EMMC flash drive got a certain amount of write access and then its dead... So i am ask you what can i do to reduce read/write: - move logs to external usb? - activate ZRAM? - disable cache...? - tmpfs? I am just at the beginning of this, so kindly let me know if you guys have some well know hints. Thanks JM

Hi All, I'm tring to make Ocroid C2 working with PiSound shield. https://github.com/BlokasLabs/pisound/tree/master/pisound-module I've compiled the module, an I'm able to install it properly. I've changed the DTS in this way --- pisound-overlay.dts 2019-01-22 23:28:59.460427794 +0000 +++ pisound-overlay_odroid.dts 2019-01-23 01:48:20.198204778 +0000 @@ -20,10 +20,9 @@ /dts-v1/; /plugin/; -#include <dt-bindings/gpio/gpio.h> - +#include "/usr/src/linux-headers-4.19.15-meson64/include/dt-bindings/gpio/gpio.h" / { - compatible = "brcm,bcm2708"; + compatible = "amlogic,meson-gxbb"; fragment@0 { target = <&spi0>; …

Hi - I'm running kernel 4.18.8-odroidc2 under stretch and I've installed linux-headers-next-odroidc2 linux-source-4.18.8-next-odroidc2 where the kernel image was linux-image-next-odroidc2 The system in general rocks - I was worried about not being able to use my RTL8812AU in the monitor mode - but it works! But I have 2 issues with 4.18.8-odroidc2, first the RTC PCF8563 module. The .config file includes the following entries CONFIG_RTC_DRV_PCF85363=m # CONFIG_RTC_DRV_PCF8563 is not set The Odroid C2 RTC shield is the one not set, namely, the PCF8563 …

Hello I'm running debian bullseye on an Odroid C4 since quite some time now and decided it was a good time to upgrade to bookworm. When I first installed armbian on this board, I remember that I had to install the Odroid HC4 image. If I'm not mistaking, there were no C4 image at the time. After upgrading my current bullseye firmware with armbian-config ( and by passing the SSD issue described in this armbian forum post by hot plugging it ), I noticed that /boot/armbianEnv.txt had this line: fdtfile=amlogic/meson-sm1-odroid-hc4.dtb whereas the amlogic/meson-sm1-odroid-c4.dtb file exists in the /boot/dtb directory. Despite having read…

I am using: Armbian_5.14_Odroidc2_Debian_jessie_3.14.71 I am a bit stumped....if I run with 3 network interfaces, everything is fine. If I add a fourth interface...the system locks up...even if the 3rd and 4th interface have no ip address. They just need to be live! I have tried 4 drastically different interfaces in case the device driver can't handle it. Anybody have any thoughts or suggestions?? THank you!