Odroid XU4

I run armbian on an Odroid HC2. Using hdparm -t /dev/sda I get merely roughly 130MB/s on buffered disk reads. This is way below the expected value for my 2TB Crucial SSD. It is obviously not a major issue as the speed is anyway bottlenecked by the gigabit ethernet. I'm just curious, does anyone get better speeds with a similar setup? I read that poor performance can result from a misaligned partition. Checking the alignment with "align-check" of parted does report that the parition alignment is fine, so I suspect this is not the issue in my case.

Hello, first of all please excuse my bad englisch! I have an Odroid HC1 an running OMV 5 with armbian since 1,5 year. When I`m check dmesg i see some problems: root@odroidxu4:~# dmesg |grep imprecise [ 47.446247] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ 47.511679] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ 47.521702] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ 47.591656] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ 47.601670] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ 47.666068] Unhandled fault: imprec…

Hello I have Odroid xu4 with fan mounted on heatsink. I found several tutorials online and I have one problem. I have Armbian buster with Linux 5.4.28-odroidxu4 I tried edit temp curve and I did it with nano /etc/rc.local # Target temperature: 30°C, 50°C, 70°C TRIP_POINT_0=30000 TRIP_POINT_1=50000 TRIP_POINT_2=70000 echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone0/trip_point_0_temp echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone1/trip_point_0_temp echo $TRIP_POINT_0 > /sys/devices/virtual/thermal/thermal_zone2/trip_point_0_temp echo $TRIP_POINT_0 > /sys/devices/virtual/ther…

Hello everyone, odroid xu4 user here with buster minimal 5.4 from https://dl.armbian.com/odroidxu4/Buster_current_minimal please have a look at the following output ... May 19 12:58:11 localhost kernel: [ 1581.893003] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250) May 19 12:58:12 localhost kernel: [ 1582.352546] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) May 19 12:58:12 localhost kernel: [ 1582.389396] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84) May 19 12:58:12 localhost kernel: [ 1582.426230] mmc_hos…

abm.tar.gz

Hi all, I wanted to do some cross arch builds on my newly installed Armbian on an Odroid-HC1 buuut, it seems binfmt_misc support is not enabled in the kernel. Can I enable it somehow without recompiling the kernel? Thank you for this great image, kernel 5.4, omg!

I know it is unsupported and all, but I just want to point out that running Ubuntu Focal(2020/05/03) with kernel 5.6 on Odroid MC1 has been destroying microSD cards. The board boots up fine, but after an apt-get update and a few minutes in, the Sandisk microSD card died and becomes read-only. I'm not sure if it is vendor-dependent, but I have tried out two new Sandisk microSD cards and they all turned read-only. This might be a kernel issue since on Debian Buster with kernel 5.4 or kernel 4.14 that never happened.

Hello, Here is a DMESG kernel dump that I'm getting everytime I boot the Odroid HC2 with a 5.4.x kernel: Also random crashes related to memory. Spoiler [ +15.195670] 8<--- cut here --- [ +0.001580] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ +0.007017] pgd = 632a7f01 [ +0.002682] [00000000] *pgd=00000000 [ +0.027685] 8<--- cut here --- [ +0.001585] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ +0.007017] pgd = 632a7f01 [ +0.002681] [00000000] *pgd=00000000 [ +0.026593] 8<--- cut here --- [ +0.001589] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ +0.007024] p…

The UN-official, UN-supported, UN-timely, UN-derrated... Exynos 5422 MEDIA TESTING SCRIPT Yes, the script is somewhat untimely, because it comes when including kernel 4.14 in Armbian next images is getting troublesome. And underrated, because this old SoC seems to be losing the focus of attention in favor of some more modern powerful ones. But it is still a great SoC, and it is worth trying to get the best out of it. The script will provide the installation of all the libraries and system configurations necessary for GPU accelerated X desktop, Chromium WebGL,VPU decoding/encoding acceleration through MFC, and GLES 3.1 / OpenCL 1.1 support. …

Hi Everyone, I'm considering getting an ODROID-HC1 to use as a simple NAS. Is this a good idea? (Yes, some of you will have seen my very similar post about the Espressobin!) My requirements are quite basic; a single SATA SSD and a single ethernet port, running NFS and Samba. I do need a newish version of Samba (required to support "Time Machine" backup from my Mac) which I believe is in Debian Buster but not in Stretch. I've been a Debian user for decades; I guess I might be happier if the hardware supplier provided a Debian image, but it's great that Armbian is available. I note that Armbian Buster for this board is described as "Testing"; should I wait for a bit…

Hi, On Odroid HC1 512GB SSD with Armbian_20.02.1_Odroidxu4_stretch_legacy_4.14.170 I've got great SSD SATA samba write speed - 110 MB/s! But I have poor only 35MB/s on Armbian_20.02.1_Odroidxu4_buster_current_5.4.19_minimal With Armbian_20.02.1_Odroidxu4_bullseye_current_5.4.19 I have the same poor 35MB/s speed. I've done three identical installations using my checklist: Spoiler #Armbian install on Odroid HC1 # Flash Armbian_<>.img #Upgrade apt update apt upgrade #Move rootfs to SSD # Make rootfs partition fdisk /dev/sda # Make filesystems …

So my sshd service won't start after a system upgrade. I have no uart access, so currently no console access. I do have access to the root drive on a usb device. I suspect systemd is having a problem starting sshd from the ssh.service unit file. But I'm not sure how to fix it. Any suggestions would be much appreciated. Here are the contents of my ssh.service file. I checked that /etc/ssh/sshd_not_to_be_run doesn't exist. I'm a little confused about the runtime directory, so I made a folder in the root directory called sshd with 0755 permissions, but that doesn't seem right. Strangely I couldn't find anything in the syslog file that mentioned s…

Since 10 days I try to install NextcloudPi on Odroid HC1. Unfortunately neither the nextcloud image nor the armbian image boots on the Odroid HC1. Also an attempt with OMV failed. In my experience with the raspi, the sd card had to have a boot partition and a rootfs partition. Etcher and dd always create only one rootfs. The blue LED flashes: short, short, pause. Also exchanged hardware was unsuccessful (HC1 and SD cards).

All credit goes to @jshc1, I only found this info in this post and split it off here so it could more easily be found later. I am not sure if this applies only to ODROID-XU4 or other Odroids as well.

Greetings, I am trying to install zoneminder into the most recent, updated and upgraded Buster Armbian image on an Odroid XU4, but libmp4v2-2 is required, and doesn't exist in any repository that I can find. Where may I find an Armbian-Buster-compatible libmp4v2-2, please?

I just installed Armbian_5.90_Odroidxu4_Ubuntu_bionic_default_4.14.127.img which will hang on sudo reboot (fan keeps spinning, no blue heartbeat led). I have another XU4 runnig the same version without the reboot issue. Armbianmonitor info uploded.

Hello, Version 5.4.0-odroidxu4 #19.11.3.342 If I use this command: sudo swapoff -a sudo swapon -a Swap switch off, but not on again. Only after reboot, swap is on again. regards ThomasD

My end game is to use hardware h264 encoding for my security camera streams (using OpenCV, etc) . The first step is testing ffmpeg. It appears that all the necessary pieces are already present in the release I'm using. If I use: ffmpeg -i centaur_2.mpg -acodec aac -vcodec h264 -b:v 2M -pix_fmt nv21 test.mp4 CPU stays below 12% and I get 44 FPS. Seems like hardware encoding is working here. If I use: ffmpeg -i centaur_2.mpg -acodec aac -vcodec h264_v4l2m2m -b:v 2M -pix_fmt nv21 test.mp4 About the same performance, but the file is 10x larger! If I use: ffmpeg -i centaur_2.mpg -acodec aac -vc…

Newbie question I would like to clone a hdd to a new ssd without reinstalling the system. What are the ways to do it on my Odroid-HC1 running Armbian Stretch with boot partition on a SD card? Thanks

Hello, I suffered a power outage and my odroid hc1 won't boot since. I also updated the kernel to 4.14.141 but the system did come back up after reboot to that kernel, it is just the power outage which seems to have caused problems. I have tried connecting the sd card and the to the laptop and ran fsck on them, no issues were found. Is there a way to debug the booting issues by say, forcing some sort of log to be writen to sd card? LED wise, red (power) LED is on, whereas green (SATA) and blue (system) seem to turn on and off repeatedly; green first, blue second, and then they both turn off at the same time. Thanks!

Hi, I'm using the minimal Armbian Debian-based image as a starting point to install my favorite desktop environment KDE and related software. I've got everything set up so that I got it working partially. I remember trying the Armbian desktop (Ubuntu flavor) but it did not have it set up out of the box IIRC (I could be wrong). I took a look at how the hardkernel guys set up their official Ubuntu image for Odroid XU4 and used that as a guide to set it up on my minimal Armbian. So here's what I've done and what I've learned I need to do according to the official image: 1. apt install mali-t62x-x11-driver xserver-xorg-video-armsoc-sun4i …

I have an xu4 board with armbian stretch(4.14.141-odroidxu4) and omv installed. I ran a script to transfer system to usb SSD. When i try to reboot the system (from cmd or omv webgui) the system just shuts down and is not started again. What could be the reason for this behaviour.

I'm new here, so please bear with me! I run an Odroid XU4 with Armbian stretch default. Recently I did a normal apt update and upgrade to kernel/dtb/headers version 5.97 (from 5.91), along with all other possible upgrades. This made the system very unstable- it had an uptime of nearly 3 months with 5.91 (all time high for the board) before the reboot, and after the upgrade it lasted a couple of hours before stalling/crashing. A downgrade to kernel/dtb/headers v 5.95 helped somewhat, but it crashed after a week or so - it may just be of those "it just happens". I went ahead and installed 5.91 and it is stable so far a few days in. The board is a bit…

Updated several HC1 to Buster. Reapplied the optimized board config, as done under stretch before. Main issue: No matter what CPU governor I set, max. frequency jumps around automagically between 1.8 GHz and 2.0 GHz. I can set performance governor to the range from 1.9 to 2.0 GHz, armbian-config confirms, and when I back out of the menu it says "soc runs between 1800 and 1800 MHz using performance governor". Even at > 90% CPU boards stay below 2.0 GHz. Minor glitches only for boards, I already upgraded from jessie to stretch: - boot.ini misses the hc1.dtb check - must manually edit - systemd misses armbian* entries, as well as the uti…

As previously posted, I have been looking to buy another board. My research continues. But today I came across this, and wanted to ask if this was something I should jump on, or do they always sell for this price? ODROID-XU4 at Hardkernel shop shows a price of $59.00, which is crossed out and now $49.00 is shown instead. I added an 8GB EMMC module, and then went to my cart to check shipping, which was $28.00 to Eastern US! I have emailed them asking if there is any cheaper shipping option, as that is almost 50% of the price! I will report back their reply if/when I receive it.

Hi, I want to try out my Odroid HC2 as an openvpn client. I don't expect great performance but I want to make sure I set it up correctly. This is why I want to ask if anyone can give any recommendations or tweaks for using it as an openvpn client. Idk much about openvpn, I know it uses openssl for de and encryption. Is there a way to use hardware de and encryption so I can speed things up and have a better download speed via openvpn? Or is hw de/encryption maybe already used by default if I just install openvpn package? Any recommendations on how to correctly set this up are appreciated.

Hi, forgive me if this has been answered. I've done my fair share of searching. Booting from sdcard works perfectly, but when I run "nand-sata-install" I get the following errors during the "cleanup" phase: sed: can't read /mnt/nand-sata-install.OIQgMo/bootfs/boot/boot.cmd: No such file or directory sed: can't read /mnt/nand-sata-install.OIQgMo/bootfs/boot/boot.cmd: No such file or directory Error while creating U-Boot loader image with mkimage grep: /mnt/nand-sata-install.OIQgMo/bootfs/boot/armbianEnv.txt: No such file or directory Even I though I run "update emmc special partition" successfully, the odroid appears to end up in a boot loop afterwards.…

Hello, Since debian buster switched to nftables as default, when i want to use the ufw-firewall, the following happens: root@homecloud:~# ufw enable Command may disrupt existing ssh connections. Proceed with operation (y|n)? y ERROR: problem running ufw-init ip6tables-restore v1.8.3 (nf_tables): unknown option "--icmpv6-type" Error occurred at line: 36 Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information. Problem running '/etc/ufw/before6.rules' root@homecloud:~# I installed both iptables and nftables, and also tried the buster-backports versions of both programs, same issue. When i run the ufw-check-requirements script, i …

Hello, i prepared a microsd card with the Armbian_5.90_Odroidxu4_Debian_buster_next_4.14.127 image and started my ODROID XU4. However the problem encountered is the failure of the NetworkManager, which of course is a main service to operate the ODROIDXU4. Sofar ARMBIAN images had been very reliable and stable in the past. The failure of starting the Network Manager something unusual for ARMBIAN. Enclosed you'll find a error messages. I appreciate very much your help and supporting comments! regards, Ireng

Hi. I have a Odroid XU4 with Ubuntu Bionic latest release (5.60), powered with this UPS: APC SmartUPS 750 VA. Apcupsd doesn't work. The problem seems related to the missing /dev/usb/hiddev0. After searching on Google, I found that apcupsd requires this feature enabled in the kernel. CONFIG_USB_HIDDEV=Y I build my own kernel enabling it, but no change. Here the output of the command # dmesg | grep Smart [ 4.125553] usb 1-1.2: Product: Smart-UPS 750 FW:651.13.I USB FW:7.3 [ 4.205622] hid-generic 0003:051D:0002.0001: hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 750 FW:651 On the Rock64 board it works without…

Hi, I am running Armbian on four HardKernel HC2's and everything is working perfectly. The four SBC's are running a Moosefs cluster running Ubuntu 18.04 and Armbian 5.85, and this leads to my questions: I am trying to decide whether to upgrade as apt is proposing moving to 5.89 The change log does not currently list 5.89 and shows 5.87 as the newest. Am I missing something? When I look at previous change logs it is difficult to decipher which fixes impact the HC2/HC1/XU4. Is there an easy way to tell? How do you decide when to upgrade? Is it even worth upgrading when running more mature boards like this one? My boards run insi…

yo guys, not sure how to fix this one, so i keep getting an adittional IP on my ethernet interface while i assigned it to static... tried to assign static conf with the armbian-config thing and by editing the /etc/network file. my dhcp is the stock ISP router network. never had this problem before, even when using other images from diferent distros. also sudo armbianmonitor -u gives me this error System diagnosis information will now be uploaded to /usr/bin/armbianmonitor: line 859: [: -gt: unary operator expected

Hello, my OMV installation on Odroid HC1 is currently at kernel 4.14.111 which is a bit outdated now. Looking at the build config [1], the kernel is fetched from hardkernel [2] which is currently at 4.14.127. What needs to happen to bring the kernel up-to-date? I have been doing packaging for Fedora for quite a while now so I am happy to help if needed. [1] https://github.com/armbian/build/blob/master/config/sources/odroidxu4.conf [2] https://github.com/hardkernel/linux/tree/odroidxu4-4.14.y

Hi Armbian Users I'm french, so excuse my poor english I'm having hard times installing Ubiquiti Unifi Controller on Armbian (running on a XU4) Armbian version : Armbian_5.59_Odroidxu4_Debian_stretch_next_4.14.66 I followed different tutorial, but no luck with those no brain tutorial. I must be retarded MongoDB is giving me a hard time, broken dependencies and so on. I understood that some managed to do it with Armbian based on Ubuntu. No luck eitheir for me. I did add the mongodb repository for 3.6 version, which support arm64 architecture. Apt never gave me the ability to install the mongodb-org package an…

Hello, I just ran a apt-update Sunday on a project and afterwards the XU only have Black screen with blinking _ in the corner, not connecting to LAN, no ssh, etc; red led is on, blue led blinking, no new logs in /var/log. Google' the issue, and several posts points to the /boot dir - however comparing with a know good SD card, I can't see much difference in this directory - other forum post points that a /dev mount point should be changed (but not to what) I can mount the broken SD card and have the following info; /etc/armbian.txt Title: Armbian 5.73 Odroidxu4 Ubuntu bionic next Kernel: Linux 4.14.94 Build date…

Hello, I had succeeded install last version of Armbian on Odroid XU4. I have WiFi USB dongle Realtek RTL8812AU chipset (ID = 0bda:8812) I see it $ lsusb Bus 003 Device 003: ID 0bda:8812 Realtek Semiconductor Corp. RTL8812AU 802.11a/b/g/n/ac WLAN Adapter $ dmesg | grep -i usb [ 9.630704] [c5] RTL871X: rtl8812au v4.2.5_10143.20140103_ASUS [ 9.887562] [c5] usbcore: registered new interface driver rtl8812au [18812.680134] [c2] RTL871X: nolinked power save leave but no Wifi interface Could anyone please help solve it

I just got a new XU4 and I tried to run both the official ubuntu 18.04 image with linux 4.14 and the armbian stretch 4.14 image (both minimal). I can hear a constant electrical squeaky noise (similar to noise from certain power supplies, usb chargers, etc) coming from the XU4 when running Armbian. The same noise is not present in the Ubuntu image. This occurs immediately after first boot (no additional configuration) and is constantly there. This is especially noticeable when the fan is off. Has anyone experienced this before?

Hi all, Thank to look at following link about my last 5.0.2 standard kernel on HC1 with some issues https://forum.odroid.com/viewtopic.php?f=93&amp;t=34237

Hello. First of all, thanks for your work and images working for my board :) I am working on S912 game board (board is used for an arcade game hardware) and would like to install gpu drivers. My issue is I don't find any documentation about from official website (ARM) I also wanted to use Panfrost but no documentation exist for installation :( I visited many site and Learn a little about Deb package and dkms package. Now I have a few questions about Can I install deb without dkms or must I install also dkms? How I can install gpu drivers if files like make don't exist on officia…

Hi, I'm using Odroid HC1 for quite a long time and I've observed much degradation on SMB/NFS speed when making upgrades to the board. I'm not sure why? Maybe I'll find some idea what it can be. Previously the board was working with speeds >100MB/s when reading from it on Windows (smb) or Linux (nfs) now max speeds on the same configuration are ~40 MB/s. That's way too slow. I don't see any process to hang on pc, while copying using smb the samba process is using not so big amount of CPU on big cores from what I see. I've grabbed armbianmonitor output so you can check it also: http://ix.io/1zrL Currently I'm working on: 4.14.87-odroidxu4 …

Hi all! I am running a nextcloud server on an odroid HC2 and a 4 TB WD red HDD. So far, so good (thanks again @Igor for the quick help with the kernel downgrade!). And since I have bought the sbc recently, I do not seem to have the older firmware version with the HDD "emergency power down" bug, i.e. I haven't heard clacking sound from the HC2. Today, I set HDD spindown to 1 hour via hdparm (wd red does not support apm) because the HDD would spin down after about three minutes on its own. The HDD does not seem to apply these settings, so I installed smartmontools to check the HDD in general. Only to find that: smartctl -a /dev/sdb1 gives this…

The Armbian htop fork doesn’t show the cores frequencies. Is this a known problem? The frequencies are available like on any other computer in the sysfs entries (cpufreq driver).

Hi! recently bought a HC2 from hardkernel to migrate my nextcloud from a raspberry pi 3b. HDD is a WD red 4 TB. armbian stretch with the 4.19 kernel, downloaded from armbian.com (Armbian_5.69_Odroidxu4_Debian_stretch_next_4.19.14). My problem: after boot (sudo reboot now or sudo shutdown -r), no possibility to login, i.e. angryip scanner doesn't show the hc2, putty times out when trying to connect. All LEDs are lit or pulsate respectively. I have to physically disconnect the power supply and reboot, then I can easily login. This is probably not very healthy for the hdd (or the sd card..., although with the ro option and zram, not much is being writ…

I needed to downgrade from 4.19 back to 4.14 so I wanted to use armbian-config/system/other. It gave me an empty list. To fix that, in /usr/lib/armbian-config/functions.sh I needed to change the apt-cache command as follows: apt-cache show linux-image-next-odroidxu4 | grep -E "Package:|version:|Version:" | sed -n -e 's/^.*: //p' | sed 's/\.$//g' I added "-next-" That gave me a list, finally. Then the next issue: apt -s -y --allow-downgrades --no-install-recommends install linux-image-next-odroidxu4=5.60 linux-dtb-next-odroidxu4=5.60 failed with: E: Command line option --allow-downgrades is not…

Odroid XU4 with Cloudshell2 Coming from 4.14.69, upgraded to 4.19.14 The fbtft_device module for the Cloudshell-LCD now reports: fbtft_device: display not supported: 'hktft9340' And yes, the source for fbtft_device seems to no longer contain hktft9340. I will ask in the Hardkernel Forum - this is just for info here. Question: When I use armbian-config to switch to an earlier package, I get a nice list, I select one and say ok, but after reboot nothing has changed. Is there something I could be missing in order to make this switch work? Never tried it before - I was hoping this would help me temporarily.

Hello, I set up an Odroid-HC1 running Armbian which works fine so far. But today I recognized htop only shows 8 CPUs of type .LITTLE running at a max of 1300Mhz while 4 of them were shown as .BIG CPUs with higher frequency before. The output of cat /proc/cpuinfo is: processor : 0 model name : ARMv7 Processor rev 3 (v7l) BogoMIPS : 36.00 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xc07 CPU revision : 3 processor : 1 model name : ARMv7 Processor rev 3 (v7l) BogoMIPS : 36.00 Features : half thumb fastmult vfp edsp neon vfpv3 t…

Hey Can anyone confirm the problem with under-clocking in Odroid HC1/HC2/XU4 with Kernel 4.19.14 / Armbian 5.70? I could always reach 2000/1500Mhz without a problem. Currently, after the last Armbian update from 5.60 to 5.70, I noticed a strange behavior that Odroid does not want to reach full clocks. With cpufrequtils min 600 max 2000 and "performance" and clocks do not want to go higher than 1800/1300Mhz temperature cpu 45.0 ° C. No changes just last updates nothing more was touched. After returning to 5.60 and 4.14.69 the CPU runs normally at 2000/1500 .... I also have the impression that HDD sometimes behaves strangely at 5.70 / 4.19.14 …

Hi, my surveillance webcam stopped working after upgrade to 4.19.14. But only on my HC2. On my other H3-Deviceses, it's working well. System diagnosis information -> http://ix.io/1yko Linux 35708-HC2 4.19.14-odroidxu4 #5.70 SMP PREEMPT Sat Jan 12 18:34:04 CET 2019 armv7l GNU/Linux Error message: root@35708-HC2:~# sudo mjpg_streamer -i "/usr/local/lib/input_uvc.so -d /dev/video0 -n -r 800x600 -f 30" -o "/usr/local/lib/output_http.so -n -w /usr/local/www -p 8080" MJPG Streamer Version: svn rev: 3:172M i: Using V4L2 device.: /dev/video0 i: Desired Resolution: 800 x 600 i: Frames Per Second.: 30 i: Format...........…

I’m relatively new to Armbian, have been running it with XU4 for couple of months. Otherwise working very well, but there’s occational (once a month) full system hang/crash or something. This is a remote server with constant load (video surveillance) and when it happens, all connectivity is of course lost and I think it can be only resolved locally with full power cycle. I’ve not yet tried to attach HDMI monitor when it’s in the crashed state, but will do it next time. Although not very optimistic if that works at all. There are nothing obvious in the logs, or it might be that I don’t know where to look. Are there any general advice what to do, how to figure this out?…

I've just installed the default desktop image, flashed directly to my emmc using etcher. Everything seems to work ok, as far as I can tell. Using the date command, it has my local time as correct, but the clock in the taskbar or whatever its called at the top of the screen is about 6 hours ahead (gmt). How do I correct this? Also, how do I verify that video acceleration is functioning or not? How do I adjust the cpu freq gov and what is the default? I looked in the boot.ini file, but it says to set the environment variables in a file named /boot/armbianEnv.txt . This file doesnt exist, so I assume I'm just to touch it and then copy over the li…

Ok, so after PHP issues I started off with a fresh armbian install and via armbian-config I installed OMV 4. Install finished without any problems but if I copy stuff via smb the tranfer speed is really bad and I don't know why. On an old install with OMV 3 I used to get nice 100 mb/s. The cpu temp also used to be at like 80 °C during copy, now it looks like this: Following extra options are set in smb.conf: min receivefile size = 16384 write cache size = 524288 getwd cache = yes socket options = TCP_NODELAY IPTOS_LOWDELAY I also checked smbd app, it's running on a big core.... I get the feeling that not all the avaiable resources of my HC2 ar…

Can anyone help me convert an Orange Pi image to run on my new Odroid XU4 as I need it running on the older kernal ARMBIAN 5.31 stable Ubuntu 16.04.3 LTS 3.4.113-sun8i The newer Kernal has a few small issues that cause a problem for my setup.

W: Size of file /var/lib/apt/lists/apt.armbian.com_dists_jessie_jessie-utils_binary-armhf_Packages.gz is not what the server reported 5780 5784 W: Size of file /var/lib/apt/lists/httpredir.debian.org_debian_dists_jessie-backports_main_binary-armhf_Packages.gz is not what the server reported 1122303 1123712 Get this when first doing apt update after fresh install. HC1 Jesse. I assumed at first it was network error, but this is consistent. Have downloaded and checksummed successful. Assumed then it was the SD card, replaced and have now tried several. Power supply is solid. I believe the hardware and bandwidth / router are fine. Simply repeat ap…

This is something I've just realized has been popping up for me for as long as I've been using armbian the past year or so with my ODROID. After a clean setup, I use armbian-config to edit the network settings (ethernet connection) to a static IP address, and everything works fine. I reboot the changes and go on my way. The problem comes after I reboot days/weeks later for kernel updates or if I lost power. The board turns on fine but refuses to show up on my network and therefore cannot SSH to the system. Looking through the SD card and checking the files shows that /etc/network/interfaces is devoid of any static IP changes made through the config, although i…

Hi, I received 2 same boards recently. One is working great, second has suffered from unexpected shutdowns. Rpimonitor has not recorded this high temperatures yet, maximum temperature recorded is not more than 90C. SoC has been utilized on 100% with ffmpeg video conversion and other tasks. I run these board on Jessie or Bionic system and have tested mainline stable and beta kernel. These board have got passive heatsink however I put 80x80 quiet slower fan on the top of heatsink, thermal compound is replaced for silver one without making problem solved. Spoiler cat /var/log/syslog | grep critical May 27 23:32:30 localhost kernel: [ 10.1…

Hello, playing around with the HC1 I noticed the lack of the nbd driver within this image. Because of the good documentation and the excellent build chain system I was able quickly to build a installation image solving my needs. My question: are there plans to add the settings necessary for nbd driver generation to the image build configuration ? Otherwise I would have to take care in case of armbian kernel updates. Thanks in advance, Joe62

I got my HC2 yesterday and am quite satisfied with it. I'm using the latest Armbian Stretch release. The spin-down of my 3TB WD Red was solved by a firmware update. Unfortunately there are still some errors in the error output (journalctl -p 3). Maybe you have a hint how I can solve it: Nov 03 18:16:42 NAS kernel: CPU4: Spectre v2: incorrect context switching function, system vulnerable Nov 03 18:16:42 NAS kernel: CPU5: Spectre v2: incorrect context switching function, system vulnerable Nov 03 18:16:42 NAS kernel: CPU6: Spectre v2: incorrect context switching function, system vulnerable Nov 03 18:16:42 NAS kernel: CPU7: Spectre v2: incorrect context swit…

I'm curious how the CPU temp value is calculated on the MOTD screen when ssh'ing in. Mine is showing 56°C, but if I run the commands: # cat /sys/devices/virtual/thermal/thermal_zone*/temp 45000 44000 48000 44000 41000 # armbianmonitor -m Stop monitoring using [ctrl]-[c] Time big.LITTLE load %cpu %sys %usr %nice %io %irq CPU C.St. 12:16:28: 600/ 600MHz 0.17 1% 0% 0% 0% 0% 0% 45.0°C 0/3 Thanks

Hi, I get this error message on armbian / omv 4 to mail: "run-parts: /etc/cron.daily/armbian-ram-logging exited with return code 1" Does anyone have a solution?

Hi! I'm attempting to activate FS-Cache on a HC2 with a 512GB SSD. I want to cache reads from other servers with NFS shares using mechanical HDDs over GbE. I run PLEX on the HC2 with SSD and the media is stored on other HC2s running OMV, with big mechanical HDDs. I figure that I can use a good chunk of the SSD to reduce the network traffic and the HDD use. I successfully use FS-Cache on a Ubuntu 18.04 laptop, together with autofs. But when I attempt to start FS-Cache on my HC2 with Bionic Armbian I get: Oct 17 23:25:34 ctrl systemd[1]: Starting LSB: CacheFiles daemon... Oct 17 23:25:34 ctrl cachefilesd[11217]: * Starting FilesCache d…

I've seen a growing memory utilization on my Odroid HC1. It turned out that `irqbalance` is a root cause. It looks like it is a known bug Right now ` irqbalance ` get restarted once per a day to keep it small. $ grep 'resource limit' /var/log/monit.log [MSK Sep 30 21:00:56] error : 'irqbalance' mem amount of 400.0 MB matches resource limit [mem amount>400.0 MB] [MSK Oct 2 01:53:31] error : 'irqbalance' mem amount of 400.1 MB matches resource limit [mem amount>400.0 MB] [MSK Oct 3 06:46:01] error : 'irqbalance' mem amount of 400.2 MB matches resource limit [mem amount>400.0 MB] [MSK Oct 4 11:38:34] error : 'irqbalance' mem amount of …

OK, OK, OK, OK No problems! :-) Just experience. Mine. My XU4 is connected to VU7 Plus, nice. charming. The startscreen when starting from a very beginning: The letters are really very small. The VU7 is adjusted to 1200x720 but it is 1024x768 Adjusting the size of the letters one should have some experience in doing that. Also in setting the keyboard. I don't have good experience without DHCP on XU4. Also not with IPv6 for the server doesn't support IPv6. (ADSL-Modem :->) https://wiki.odroid.com/accessory/emmc/recovery_xu4 is very good No problems. Working with Configuration utility one can get lost without reading th…

Hello, I'm looking for some support with installing plex media server on an Odroid HC1 running the non-desktop stable release of Armbian Bionic. I first used armbian-config to select and install 'plex' but the service didn't start. I then removed the installed 'plexmediaserver-installer' and any created 'plexmediaserver' files/directories & reinstalled manually as shown below: ahaslam@odroidxu4:~$ sudo apt update Hit:1 http://ppa.launchpad.net/bitcoin/bitcoin/ubuntu bionic InRelease Hit:2 http://ports.ubuntu.com bionic InRelease Get:3 http://ports.ubuntu.com bionic-security InRelease [83.2 kB] Get:4 http://ports.ubuntu.com bionic-updates InRelease [88.…

Hi, I'm running into a problem I can't solve. On my new Odroid HC1 I'm trying to set up a SFTP with chroot, but no matter what I'm trying it doesn't work on Armbian (or OMV). Tried it multiple times with a clean Armbian (Armbian_5.59_Odroidxu4_Debian_stretch_next_4.14.66 - also tried the Bionic image) install, simply added a user, added the required lines to sshd_config but each time I get a "Broken Pipe" error. On the other side when I use the minimal Ubuntu image from Hardkernel.com the chroot SFTP works without a problem. But I would like to run Armbian. Has anybody been able to create a chroot for SFTP on a Odroid HC1/2? Could it be…

hey there, I'm using an odroid xu4 with the cloudshell 2 with 2 drives in RAID1 and Armbian with Debian 9 Stretch as my OS, built via Vagrant 2 weeks ago. The /boot partition sits on a sd-card, the OS on the harddrive. I''ve copied both via dd on both devices(boot an card, rootfs on harddrive), and after the first boot it worked flawlessly, because the boot information uses the UUID, not the /dev path. After the first boot and configuration of another user and so on, I rebooted the system to let it resize the rootfs to extend it to 2TB, which is the size of the harddrive. But after this, it seems that cryptroot cannot decrypt the …

So I have this issue with the XU4, where at times when I start device from the main power button, it doesn't seem to properly connect to the LAN, in such a way that I cannot ssh to it, nor ping it. Since the device is headless, and I can't control it through LAN, I have no way of looking at dmesg during the problematic boots. Are there specific logs I could look at to diagnose this problem?

Hi all! :-) To those who made the excellent work for my oroid! Well done, very well done! Well, just one point, maybe: Sep 08 13:47:55 odroidxu4 systemd[1]: Starting Atop process accounting daemon... Sep 08 13:47:55 odroidxu4 atopacctd[17567]: /run/pacct_shadow.d: File exists Sep 08 13:47:55 odroidxu4 systemd[1]: atopacct.service: PID file /run/atopacctd.pid not…ctory Sep 08 13:47:55 odroidxu4 systemd[1]: Failed to start Atop process accounting daemon. Sep 08 13:47:55 odroidxu4 systemd[1]: atopacct.service: Unit entered failed state. Sep 08 13:47:55 odroidxu4 systemd[1]: atopacct.service: Failed with result 'resources'. Hint: Some lines wer…

Does anyone know any way to fix the annoying way the fan works on this device? Even on idle load, the fan spins up every couple of minutes, keeps spinning for a few seconds, then turns off again, only to repeat a few minutes later. I can't even sleep in the same room the device is in... I've tried using this: https://github.com/f1vefour/odroid-xu4-fan-control And it hasn't really solved anything, as the fan cannot start on PWM values lower than 100... it instead makes squeaking noises. So having adjusted the script, nothing has really changed. Is there something I could do to fix this in software? Perhaps something that doesn't involve getting the heatsink …

Today I wanted to upgrade from jessie to stretch, I'm following this website. After changing the word jessie to stretch in /etc/apt/sources.list and in every file in /etc/apt/sources.list.d/* I noticed that changing the omv-extras-org.list from: # OMV-Extras.org deb https://dl.bintray.com/openmediavault-plugin-developers/erasmus jessie main # OMV-Extras.org Testing deb https://dl.bintray.com/openmediavault-plugin-developers/erasmus-testing jessie main to # # OMV-Extras.org deb https://dl.bintray.com/openmediavault-plugin-developers/erasmus stretch main # OMV-Extras.org Testing deb https://dl.bintray.com/openmediavault-plugin-developers/erasmus-testing stre…

Hello, I am interested in getting an Odriod-HC2 to use as a small LXD host to run a couple services that require decent hard disk size and performance. Does the headless jessie or ubuntu 4.14 images support or already include LXD? P.S.; I tried to search for this but did not see a question asked.

So I wanted to set up an Odroid XU4 as a low-power low-cost NAS and "seedbox" for a personal project, and I wanted to have a GUI that doesn't take too many resources (or spin the fan too much) due to the fact that qBittorrent can't run as a thin client, and I don't want to have to use a WebUI, nor do I want to use a different client (Transmission frequently has security issues, and Deluge is a bit too resource-intensive). I'm currently using the XU4 headless, and only have it hooked up to LAN, so it's a bit difficult to tell what's going on at system initialisation, and since I'm controlling the device through SSH, I'm unable to manually start X11 after booting and l…

Does someone know why the kernel reverted to 4.9.* from 4.14.*?

Hi - is it possible to install linux-headers from repositories on the XU4, so that DKMS builds of wifi adapters will work properly? I'd like to have DKMS handle rebuilding the driver for my RTL-8812au based wNICs on the XU4, as it does on my x86-64 devices. Thank you!

Hi, I am trying to get my Xu4 to boot from an emmc card, I am using Armbian Bionic mainline kernel 4.9.y. I can write this to SD card, and it boots and runs OK. I prepared the emmc card using the inbuilt system nand-sata-install script. The emmc card will not boot. I tried a couple of other iso.s same non result. Checking the forum I found this thread started last year:- This thread was HIJACKED by Tkaiser , who turned it into a discussion about OMV, and I cannot see a successful conclusion to the original boot problem! Please can you advise me of the method to get my emmc card to boot on my xu4, using the curre…

Hello, I am the main developer of NextCloudPlus. NCP is a community project to make it easier to run and setup a Nextcloud instance in ARM boards, by providing configuration tools and setup wizards for typical management tasks such as backups, SSL certificates and more. We have just released the first stable version of Armbian based images with NCP for Odroid XU4 / HC1 / HC2. Check it out at the downloads section. More boards will come soon Feedback, testing and development help are very welcome Cheers,

I tried to install armbian to my internal sata drive (SSD: Samsung Evo 850). But the device fails to boot after the root fs is moved. I used the command nand-sata-install with following option: Boot from SD - system on SATA or USB I tried different filesystem formats (ext4, btrfs) and armbian builds: Armbian_5.37_Odroidxu4_Debian_jessie_next_4.9.71 (stable) Armbian_5.37_Odroidxu4_Ubuntu_xenial_next_4.9.71 (stable) Armbian_5.41_Odroidxu4_Debian_stretch_next_4.9.83 (self-built) I dont have a terminal adapter to access the boot logs. Any hints how to get additional information or to fix this issue?

Hi Guys, I tested both the odroid official and armbian images for the XU4. Both run well, but I prefer the armbian image. I have attached my 800x480 hdmi display, it works, but there's a purple line at the left side of the display. ( I think it's one pixel wide) This is not the case with the odroid official image, so I guess it's a configuration issue. I took a look at the boot. ini file, but I don't see anything that rings a bell. Can somebody point me to the right direction?

I have some HC1 running since last year. Before going into production I did SATA install, NEXT kernel, firmware and stretch update (I need that) and all updates offered through apt since then. I have read about newer armbian releases that my machines do not load and further HC1 optimization which I can´t find in my armbian-config. I wonder whether my setup will receive proper updates. It would be quite a hassle to reinstall. Now I have: Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.9.61-odroidxu4 Linux HC1 4.9.61-odroidxu4 #2 SMP PREEMPT Wed Nov 22 16:34:23 CET 2017 armv7l cat /etc/apt/sources.list deb http:/…

A recent check of failed services showed me that following service failed: systemd-update-utmp-runlevel.service Checking via journalctl I see this: Failed to write utmp record: No space left on device So far I understood it has to do with the space for the logs being full, I can delete logs to make place. My question is, how could I have that done by default in an easy way? The message itself doesn't bother my that much but I guess there are no new logs created if there's no space which isn't ideal.

Hi, I've just ordered a Xu4 to use it as a desktop and I have never used armbian before. Is webgl is running fine in chromium browser? I want to run Construct 3 on it. Thanks in advance!

Hi, yesterday I did a apt upgrade and noticed that my omv install also got updated. Now copying from my HC2 I only get like 50 mb/s. I always got like 100 mb/s..at least win explorer showed this, I know it's not accurate. Could the update have erased/overwritten all these nice tweaks @tkaiser made for us to increase tranfer speed? That would be very unfortunate :/ Any chance I can roll back the omv update?

Hello everybody, I'm very new to the topic 'armbian' and yet excited. Just played with the BananaPi and downloaded the distro from the first link I got (light/mainline I think). Now I have bought an Odroid XU4 and want to build a Home-Server / NAS with it, wondering which distro to choose. Of course without the heavy-load desktop, but (xenial) next oder default? Thank you. Regards AXEL

Hi, just bought a HC1 and tryin to setup Armbian. I installed Armbian_5.37_Odroidxu4_Ubuntu_xenial_next_4.9.71, works with SDHC. Now I put in my ADATA SP550 (480GB) SSD, but something fails, see dmesg: Spoiler [ 5.096332] r8152 6-1:1.0 eth0: v1.08.8 [ 5.118014] r8152 6-1:1.0 enx001e06326386: renamed from eth0 [ 5.207225] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd [ 5.228766] usb 4-1: New USB device found, idVendor=152d, idProduct=0578 [ 5.228786] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.228802] usb 4-1: Product: USB to SATA bridge [ 5.228…

I recently hooked up my XU4 to a DVD/CD Enclosure, essentially just SATA to USB, and am having an issue mounting the drive. After researching online it seems this is a filesystem issue. So, I was wondering if anybody else has encountered this problem, and if so, how did you fix it? Thanks Armbian: Image: Armbian_5.37_Odroidxu4_Ubuntu_xenial_next_4.9.71_desktop.7z Kernel: [default] 4.9.61-odroidxu4 #2 SMP PREEMPT Wed Nov 22 16:34:23 CET 2017 Errors: # mount -t iso9660 /dev/sr0 /media/ceru/cdrom mount: /dev/sr0 is write-protected, mounting read-only mount: wrong fs type, bad option, bad superblock on /dev/sr0, missing co…

I installed a Debian Jessie on an Odroid HC1, and trying to connect an encrypted disk to it via USB. blkid lists the device: # blkid /dev/sdb1: UUID="2288876d-0fe8-4b5a-b7d1-1660df8b2e25" TYPE="crypto_LUKS" PARTUUID="c8895b7f-01" but when I try to open it with luksOpen: # cryptsetup luksOpen /dev/sdb1 sdb1_crypted Enter passphrase for /dev/sda1: After entering the passphrase (and Enter), it hangs. The SSH connection times out after 1-2 minutes (where to enlarge?) and there is no HDMI on the HC1, so I am left blind. The disk was created and used in another system and worked perfectly on a Raspberry PI and my Linux PC. I created a key file and added…

I learned that the cpu on my hc2 has 4 'slow' cores and 4 fast ones. Now I would want certain apps to always use the fast cores. I found `taskset` to do so. My idea was to just add `taskset --cpu-list 4,5,6,7` in the .service file of the desired app in the execstart line in front. To have it always use the big cores. Would this work? Also I have apps 'calling' unrar to extract files. I don't know how I would do it in this case. I think it'll be a bit complicated to tell the apps to call unrar with `taskset --cpu-list 4,5,6,7`. Is there a way to have unrar always run on the big cores?

Dear all, thanks for the work of you, to provide us with the Armbian Images for our arm-based boards. BUt i've a small issue, starting the last Image for Odroid XU4. If I write the Image to a SD-Card and start the XU4, all Things run well. When I write the Image to my eMMC-Card (original Hardkernel, 64GB), the XU4 doesn't start. Normally, it's not such a big Problem, but there is a massive speedup, using eMMC with XU4. How can I get Armbian startet, installed on an eMMC? Many thanks for your Support, Burkhard

Dear all. After a update/upgrade and dist-upgrade.. a few weeks a go i think there is something going wrong on my Xu4 After every update and upgrade i still get the same errors: root@odroidxu4:~# sudo apt-get update Err:1 http://apt.armbian.com xenial InRelease Could not resolve 'apt.armbian.com' Err:2 http://us.archive.ubuntu.com/ubuntu xenial InRelease Could not resolve 'us.archive.ubuntu.com' Err:3 http://us.archive.ubuntu.com/ubuntu xenial-security InRelease Could not resolve 'us.archive.ubuntu.com' Err:4 http://us.archive.ubuntu.com/ubuntu xenial-updates InRelease Could not resolve 'us.archive.ubuntu.com' Err:5 http://us.archive.ubuntu.com…

Spoiler [58531.860637] lowmem_reserve[]: 0 0 0 [58531.860654] Normal: 56*4kB (H) 44*8kB (H) 48*16kB (H) 37*32kB (H) 14*64kB (H) 1*128kB (H) 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 3552kB [58531.860733] HighMem: 27*4kB (UM) 42*8kB (C) 1*16kB (C) 0*32kB 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 460kB [58531.860786] 304403 total pagecache pages [58531.860790] 15267 pages in swap cache [58531.860794] Swap cache stats: add 382457, delete 367190, find 125239/202183 [58531.860798] Free swap = 1630472kB [58531.860801] Total swap = 2097148kB [58531.860805] 518656 pages RAM [58531.860809] 322048 pages HighMem/MovableOnly [58531.860813] 8201 pages re…

I recently built Armbian with Open Media Vault installed at build time. After configuring the system and wanting to make a backup image when I use Win32DiskImager to create an image it succeeds but after I plug the SD back in the board it wont boot. I recently lost power and I have the same issue of the board not booting after power is disconnected. If I make a fresh image it can boot and reboot but if I ever remove power the board will not boot into the OS. What happens when there is power loss the alive led is blinking and the HDMI outputs a black screen with a blinking cursor even when left for hours it doesn't ever stop. The SD card is readable and can vie…

My System: ODROID XU4 Armbian stable: Linux odroidxu4 4.9.56-odroidxu4 USB-3 HDD Cage with 3 SATA drives, connected to XU4 via USB2-HUB (Since XU4 onboard USB3 does not recognize drive cage, never has) The drives are 1.5TB, 3TB and 4TB in size. All have one partition of full size and are encrypted with luks/dm-crypt. I'm switching from a Debian 8 system on the XU4, which had no problem with disk decryption. After the initial setup on Armbian I'm now trying to use those disks. I can successfully decrypt and mount the 1.5 TB disk. But when I do cryptsetup luksOpen /dev/disk/by-uuid/9ef4da01-8c26-48f1-a945-d2f419068e2f somename th…

hi, I am VERY happy with how 4.9 is running odroid-xu4. as i use it as media server and player wanted to see if i could get latencies (poitential) down by applying latest RT patches that are in line with current xu4-next kernel sources. added pathes to userpatches/kernel/odoirdxu4-next directory, build process went fine, have selected FULL-RT but it does not boot (final image) source: https://github.com/hardkernel/linux/tre ... dxu4-4.9.y rt-patches: https://www.kernel.org/pub/linux/kernel ... ts/rt/4.9/ it compiles ok but it does not boot ... has anyone looked at what the issue might be ? i don't have serial debuigger yet, have ordered bu…

After a major failure of my file server I bought a pair of seagate desktop USB3 drives to use for temporary storage while I sort out the mess. I plugged them into an XU4 and started transferring several 100GBs of data only to have it lock up solid. dmesg indicates a number of uas restarts, the last of which doesn't complete. I had the same thing on another SBC (one of the orange PIs I think, although I can't remember which model) and I also found references to the same problem on x86 boxes, so I think the problem is fairly generic. Apparently it can be worked around by adding a conf file to to /etc/modprobe.d, but I haven't got that to work yet (time has been …

I am trying to set up serial communications over the CON10 connector (UART0 pins 4,5,6,8) to another board (BeagleBone Black) to transmit data parsed as strings between the boards. Based on this link, this should correspond to /dev/ttySAC0. I have been unsuccessful in achieving communication via these pins and device node. In using setserial to probe the port settings, I was concerned about the following output: setserial /dev/ttySAC0 /dev/ttySAC0, UART: undefined, Port: 0x0000, IRQ 83 In using dmesg to probe for more information, I found an identifier for SAC0: dmesg | egrep -i 'serial|tty' [ 1.020896] [c4] 12c00000.serial: ttySAC0 at MMIO 0x12…

Is there anywhere I can find pulseaudio-equalizer or package with similar capabilities for Armbian on XU4? It appears to be out there for arm64 ...

Hi, I'm considering reinstalling OpenMediaVault using an Armbian image as the NAS performance on the current image I use is very bad (4-7 megabyte via Samba over Gigabit) and I've heard that it should be much better with Armbian. Since I have some data on my NAS that's protected with Ecryptfs, I wonder if the kernel config in a future update could be changed to include Ecrypt_fs module support. Thanks for considering making this change. All the best, Sebastian EDIT: tkaiser from the openmediavault forum took care of this. Thanks!

Dear all.problem with my Xu4My router is a bit buggy..[ i think or my isp ]When my isp has a hick in the wan lineMy Xu4 does not automatic reconnect with my lanIs there a option to auto reconnect when there is a connection lose Now i reboot the xu4 manually and then is working everything fine'I use the latest armbian on my Xu4

I wonder if anyone can help. I have downloaded the latest build for my odroid-xu4 and have the kernel version 4.9.51-odroidxu4. The trouble is I cannot find any where the kernel headers for this particular version. The kernel headers that come with the dist is 4.9.31-odroidxu4 and when I do apt-get kernel-headers-$(uname -r) or apt-get kernel-headers-next I get version 5.0.33 and I cannot seem to download the version that I need to compile drivers. Anyone know where the version 4.9.51-odroidxu4 linux headers are? Thanks

Just a little question: I'm new with this device, but not with armbian. Tested the Image for HC1 and it works fine, but if i try to boot root filesystem from sata device (using armbian-config, sata install) it didn't boot. Anyone tested that with success? Thx

Hi All, I've just got the new Orange Pi R1 and as expected it's working just well with the Orange Pi Zero armbian image. The only thing I'm struggeling with is the Wifi driver. The driver compiles succesfully but it seems that the kernel needs patching as well: ... CC [M] /usr/src/rtk8189es-2015-12-15-90ed86d42d/rtl8189ES//hal/OUTSRC/rtl8188e/phydm_RTL8188E.o CC [M] /usr/src/rtk8189es-2015-12-15-90ed86d42d/rtl8189ES//platform/platform_ops.o CC [M] /usr/src/rtk8189es-2015-12-15-90ed86d42d/rtl8189ES//platform/platform_ARM_SUNnI_sdio.o CC [M] /usr/src/rtk8189es-2015-12-15-90ed86d42d/rtl8189ES//core/rtw_mp.o CC [M] /usr/src/rtk81…