Rockchip

Hi, I tried to activate the SPI interface on a Tinkerboard2S. I used the last Armbian version (Armbian_community_25.2.0-trunk.110_Tinkerboard-2_bookworm_current_6.6.63_minimal). I edited the /boot/armbianEnv.txt and add the overlays, I found different parameters and all doesn't work, I tried: overlays=spi0 spi2 overlays=spi-spidev param_spidev_spi_bus=0 and via armbian-config: fdt_overlays=rockchip-rk3399-spi-spidev But with all approaches I didn't get a /dev/spi* device. Any ideas? TIA

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

ioanker

December 31, 20241 yr

Issue: LEDs don't work and /sys/class/leds is empty after upgrade to 24.11.3 on ROC-RK3328-CC Renegade (boot & system on eMMC.) Before upgrade, 24.11.1 had LEDs working with "firefly:blue:power" and "firefly:yellow:user" 24.11.1 had /sys/class/leds/firefly:blue:power pointing to /sys/devices/platform/leds/leds/firefly:blue:power as shown here: On this (LED working) installation BEFORE UPGRADE: " armbianmonitor -u " logging output here: https://paste.next.armbian.com/ucizofikay Note the pretty names + armbian firmware show 24.11.3, while the other packages held back to 24.11.1 by the setting in armbian-config tool. LEDs…

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 2 followers

Tim Makarios

January 26, 20251 yr

Hello everyone, I’m using a Radxa Zero 3E with Armbian 24.8.1 Bookworm OS and trying to connect a device to Radxa via UART. However, I can’t seem to find the ttyAML0 interface. The only UART interfaces visible are ttyS1 and ttyFIQ0 , but neither works for my setup. I have connected the device to the UART_AO_A pins (pins 8 and 10). Additionally, when I go to armbian-config -> System -> Hardware, no hardware appears on the screen. Could this issue be related to the Armbian image I am using? I’ve already tried the b6 image, but it has a boot problem. I also noticed that the other official Radxa images are marked as pre-release. …

• 0

  Reputation Points

• 1 reply
• 2.5k views
• 1 follower

Werner

September 19, 20242 yr

In order to review the Tinker Board boot logs via serial console, I set up armbianEnv.txt to get the logs. But Armbian didn't output anything. Can anyone tell me what is wrong? As long as I reviewed boot.cmd, the serial port was assigned to /dev/ttyS2. So I used UART2 GPIO pins (GP7C7 for TX, GP7C6 for RX) to interact. (snip) if test "${console}" = "serial" || test "${console}" = "both"; then setenv consoleargs "console=ttyS2,115200n8 ${consoleargs}"; fi (snip) The barudrate is 115200. Of course, I re-checked my connection between USB-UART serial cable and UART2 GPIO pins (USB-UART RX to GP7C7TX, USB-UART TX to GP7C6 RX). Any infor…

• 0

  Reputation Points

• 1 reply
• 5.7k views

Guest

August 13, 20206 yr

We have tried to connect the MIPI DSI 10.1 inch OPI Display. It is working fine alone but when we tried to connect another display with the HDMI. we expect it to work as our 2nd display but it did'nt work unless i disable the MIPI display from the OPI Config.

• 1

  Reputation Points

• 1 reply
• 2.3k views

ArmBoy1988

June 10, 20242 yr

when I switch to static IP, there is no a connection to default gateway. but when using DHCP everything works fine. $ ip route default via 192.168.88.1 dev end1 proto static metric 100 169.254.0.0/16 dev end1 scope link metric 1000 192.168.88.0/24 dev end1 proto kernel scope link src 192.168.88.32 metric 100 $ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 2: end1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 …

• 0

  Reputation Points

• 1 reply
• 2.1k views

0xf1

October 15, 20241 yr

Hello!! I just got my Orange Pi 5 the other day and am trying to 'port' a program I've been working on for RPi4b over to this new board. The program is using ffmpeg to decode h264 and hevc video streams. My main question is how do I need to configure the ffmpeg codex context and formats to make use of (ideally zero copy) HW accelerated video decode on Orange Pi 5? For the raspberry code I was using these: avcodec_find_decoder_by_name("hevc"); and avcodec_find_decoder_by_name("h264_v4l2m2m"); together with codec_context->pix_fmt = AV_PIX_FMT_DRM_PRIME; // for zero copy video path But this does not work when compil…

• 0

  Reputation Points

• 1 reply
• 5k views

fredrum

February 28, 20233 yr

Hi, I've read on here that you can apparently switch to a stable edge branch through Armbian Config, but the closest I can find is 'switch to rolling packages repository' and 'distribution upgrade to rolling unstable'. Are either of these correct? I'm running the Ubuntu Noble 6.12 kernel, btw. Many thanks.

• 0

  Reputation Points

• 1 reply
• 1.8k views
• 1 follower

Farfalla2728

January 25Jan 25

I have a nice video acceleration on chromium and Ubuntu noble, but not with a video player. Maybe someone can say one and how to install.

• 0

  Reputation Points

• 1 reply
• 2.2k views

maka

October 6, 20242 yr

Help me out, please. Begginer

• 1

  Reputation Points

• 1 reply
• 3.8k views

Igor

December 4, 20241 yr

The armbian Khadas Edge 2 Noble image seems to be corrupted? its literally impossible to extract.

• 0

  Reputation Points

• 1 reply
• 1.7k views
• 1 follower

Werner

May 17, 20251 yr

Saw this over on the LKML... some folks might be interested in this one... http://lkml.iu.edu/hypermail/linux/kernel/1901.0/02233.html Changes checked in against staging... staging: video: rockchip: video codec for vendor API staging: video: rockchip: fixup for upstream staging: video: rockchip: add video codec arm64: dts: rockchip: add video codec for rk3399

• 0

  Reputation Points

• 1 reply
• 4.3k views

TonyMac32

January 7, 20197 yr

I'm trying to get the RPI 7in touchscreen working on armbian with my Tinker Board. Can anyone tell me how?

• 0

  Reputation Points

• 1 reply
• 2.6k views

TonyMac32

June 3, 20197 yr

My new RockPi-E works well except for a reboot. Have to power it off/on to recover. Is it a known problem? Any solution/workaround? Thanks for your time Chris

• 0

  Reputation Points

• 1 reply
• 3.3k views

Werner

March 3, 20215 yr

I created a deb package for my own application. How do I import it for compilation and installation?

• 0

  Reputation Points

• 1 reply
• 2.3k views

Werner

September 3, 20242 yr

I played a bit with the SenseHAT from the RPi guys. Doesn't work fully but I get the first things working. What does run: Joystick 8x8 led matrix (partly, seems that there are some parts of the framebuffer not fully working) What doesn't run: all the sensors attached on the board What's missing: load it devicetree overlay (at the moment it's coded into the main dts) how-to what's needed to get it working on your tinker too I'll keep you updated.

• 1

  Reputation Points

• 1 reply
• 4.2k views

Larry Bank

April 9, 20188 yr

Hello people, Happily running Bookworm, because it was the mainstream download for OPI5 a few months ago, I now see that the main download for OPI is back to Jammy. Apart from hardware accceleration, Bookworm runs great for me. In fact HA is not crucial for my server usage, though it would be nice. Question: what is the reason the main OPI5 download is now back to Jammy in stead of Bookworm? And what would be the advantages of going back from Bookworm to Jammy? (Got the aluminium passively cooling case for the OPI5, so far it's been great, 10 minutes of stresstesting all 8 cores doesn't get above 70 degrees celsius. For reference my…

• 0

  Reputation Points

• 1 reply
• 1.7k views

Marc R

January 3, 20242 yr

I somewhat recently used Armbian Build to compile a desktop Bookworm image, which is quite stable and functional except for EMMC support. Packages: Debian stable (bookworm) Support: DIY (custom image) Linux Atlas 6.1.84-vendor-rk35xx #1 SMP Tue Dec 24 13:36:04 UTC 2024 aarch64 GNU/Linux My question is where can one find the current status of the various kernel versions support for features like I2C, SPI, EMMC, MESA, etc.? I recognize that newer kernels like 6.12.yyy are very much a WIP. I also would love more information on the the RK3588 kit used with kernels to backport features.

• 0

  Reputation Points

• 1 reply
• 3.5k views
• 2 followers

Werner

January 8, 20251 yr

I was running on Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop. For the most part, it worked but the mouse cursor would randomly disappear while remaining functional but invisible. I tried to upgrade using apt-get update and apt-get full-upgrade and after a reboot, it now just displays a flashing underscore. I can SSH into the OS so it's partially functional. Shows as Armbian 23.02.2 Jammy with Linux 5.10.110-rockchip-rk3588 Contents of boot.log: ------------ Mon Feb 27 07:24:15 PST 2023 ------------ done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running…

• 0

  Reputation Points

• 1 reply
• 1.9k views

Werner

February 27, 20233 yr

Title, i just download the right version used balenaEtcher for flashing it on microssd and its stuck on blue light(booting), how i can solve it

• 0

  Reputation Points

• 1 reply
• 2k views

Igor

September 8, 20251 yr

So recently I flashed Orange Pi OS to SD card, booted from there, updated system, firmware and flashed bootloader to SPI flash. I already had an external HDD with Armbian flashed, and tried to boot from there, but no luck. Afterwards, I tried to boot Armbian from SD card, but I can't boot any system that is not Orange Pi OS (and especifically, it needs to be from SD card, can't also boot from USB even in OPi OS). Tried with different SD cards and USB devices, no luck I believe I need to erase SPI flash in order to boot from SD again, but, how can I do it? Used latest OrangePi OS and Armbian Jammy CLI from 23/01 (stable release)

• 1

  Reputation Points

• 1 reply
• 9.4k views
• 2 followers

martivo

February 14, 20233 yr

##O#O## OS: Armbian 25.8.1 noble aarch64 ####### Host: Orange Pi 5 Plus ########### Kernel: 6.1.115-vendor-rk35xx ############# Uptime: 1 day, 8 hours, 17 mins ############### Packages: 1852 (dpkg), 5 (snap) ################ Shell: bash 5.2.21 ################# Resolution: 3840x2160 ##################### DE: GNOME 46.0 ##################### WM: Mutter ################# WM Theme: Adwaita Theme: Adwaita [GTK2/3] Icons: Adwaita [GTK2/3] Terminal: x-terminal-emul CPU: (8) @ 1.800GHz …

• 0

  Reputation Points

• 1 reply
• 3.5k views

amazingfate

September 27, 20251 yr

Hi. I'm running Armbian 22.05.3 Focal with Linux 5.10.60-rockchip on an Asus Tinker board. Can someone tell me how to enable SPI? I've seen instructions that say you should be able to run armbian-config and go to System > Hardware > spi-spidev, however the Hardware menu does not exist for me.

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

Serkan Polat

December 23, 20223 yr

Hi! I have installed Armbian buster 21.08.3 and can`t discover any externally connected i2c devices, such as rtc or ssd1306 Any ideas? i2cdetect -l i2c-2 i2c rk3x-i2c I2C adapter i2c-0 i2c rk3x-i2c I2C adapter i2c-5 i2c rk3x-i2c I2C adapter sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- UU -- -- -- -- 20: -- -- -- -- -- -- -- -- …

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

Werner

November 10, 20214 yr

Hi so there is a wip for RockPro64 but Kernel development and some other builds like MrFixIt have made gr8 advancement. Wondering if you could start support for rp64 or maybe update the wip since kernel has greatly improved.

• 0

  Reputation Points

• 1 reply
• 3.2k views

Igor

March 31, 20197 yr

Please advise (see low/high values): nvme-pci-0100 Adapter: PCI adapter Sensor 1: +31.9°C (low = -273.1°C, high = +65261.8°C) Sensor 2: +39.9°C (low = -273.1°C, high = +65261.8°C) Sensor 8: +31.9°C (low = -273.1°C, high = +65261.8°C)

• 0

  Reputation Points

• 1 reply
• 1.3k views

royk

September 4, 20233 yr

I finally got wifi working on a fresh install of 24.5.1. Video acceleration is working perfectly in Chromium but I am not having any luck playing h264 mp4 videos with hardware acceleration in vlc or mpv. Is this possible or am I missing something? CPU is around ~30% with chromium playing 4k youtube but if I play one of my mp4 files it's a solid 130%

• 0

  Reputation Points

• 1 reply
• 2.6k views
• 1 follower

Sr_-Caio

June 9, 20242 yr

I use the spi0 of Renegade to drive a 3.5-inch touchscreen, both the lcd and touchscreen use the same spi0, but different "CS". If I don't touch, the display is ok. But when touch the screen, the display gets messed up, looking like the colors are misaligned starting from an offset value. Anybody has experience of it ? Thank you! (The first and second images get messed up as I touch on screen, the third image is ok as I don't touch.)

• 0

  Reputation Points

• 1 reply
• 2.9k views

DavidJS

May 17, 20224 yr

Hi all! I have a problem with Armbian images on kernel 5.10.160 (jammy & bookworm Armbian_23.11.1_Orangepi5-plus_***_5.10.160.img) When starting from the SD card the nvme device is not visible root@orangepi5-plus:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS mtdblock0 31:0 0 16M 0 disk mmcblk1 179:0 0 58G 0 disk ├─mmcblk1p1 179:1 0 256M 0 part /boot └─mmcblk1p2 179:2 0 57.1G 0 part /var/log.hdd / mmcblk0 179:32 0 233G 0 disk mmcblk0boot0 179:64 0 4M 1 disk mmcblk0boot1 179:96 0 4M 1 disk zram0 254:0 0 7.7G 0 disk [SWAP] zram1 254:1 …

• 0

  Reputation Points

• 1 reply
• 1.9k views
• 1 follower

ozacas

March 27, 20242 yr

Hi, I am currently using rock-5-itx to setup a NAS. Everything is working fine. uname -a: Linux amberbyte 6.1.75-vendor-rk35xx #1 SMP Thu Nov 28 03:16:11 UTC 2024 aarch64 GNU/Linux Now, I wanted to update RKNPU version from 0.9.7 to 0.9.8. So, again I recompiled the image with the updated drivers. Using Pi-imager flashed it onto an SD card. When I tried to boot I am getting the following error message from the serial output: ./compile.sh build BOARD=rock-5-itx BRANCH=vendor BUILD_DESKTOP=no BUILD_MINIMAL=yes EXPERT=yes KERNEL_CONFIGURE=yes RELEASE=bookworm DDR 9fffbe1e78 cym 24/02/04-10:09:20,fwver: v1.16 LPDDR5, 2400MHz channel[0] BW…

• 0

  Reputation Points

• 1 reply
• 2.4k views

Werner

May 20, 20251 yr

Degin: MounlAng root Tile syslel ... Degan: munning escrapusr cucad-lop ... uonc. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. done. Geve up waiting for root file system device. Cowmon problems: ⁃ Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! UUID=db80a2ac-ec37-4fda-91db-92604becfcce does not exist. Dropping to a shell! BusyBox v1.30.1 (Ubuntu 1:1.30.1-7ubuntu3.1) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) …

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

TheFlash

October 23, 20241 yr

Hi can anyone advise if they have come accross this issue. so somehow HDMIRX seems to be the hdmi input controller starts to freak out for no reason there is nothing plugged into it EVER and will randomly start to outpur this to console im thinking maybe the HDMIRX is faulty and want to remove it, I have tried removing it removed the DTB , decompiled and edited and removed it from DTB, tied to blacklist it but with no effect it does not stop spamming and the device [ 89.603095] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_phy_register_write wait cr write done failed! [ 89.613765] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_phy_register_write wa…

• 0

  Reputation Points

• 1 reply
• 2.5k views
• 1 follower

Werner

March 14, 20251 yr

If any of you have experienced skipping and popping when seeking with vlc, you can try setting the audio sink to ALSA and one of the rockchip-es8316 options. That will smooth out the audio playback BUT you will quickly discover that anything pulseaudio related is locked out of using the soundcard while vlc is up. Instead, try this. Set vlc audio back to pulseaudio (or automatic, seems to map to the same thing) and then change these two lines in /etc/pulse/daemon.conf: -; default-sample-rate = 44100 -; alternate-sample-rate = 48000 +default-sample-rate = 48000 +alternate-sample-rate = 44100 Restart pulseaudio with systemctl --user …

• 0

  Reputation Points

• 1 reply
• 2.3k views

Popolon

December 5, 2025Dec 5

The apt source is always overwritten by the cache source when modified. How can I modify this cache source. How can I modify this cache source?? help help

• 0

  Reputation Points

• 1 reply
• 2.2k views

Werner

August 29, 20251 yr

Hi everyone, Has anyone been able to get gpu hardware acceleration to do encoding/decoding on Jellyfin on the orange pi 5? Thank you

• 1

  Reputation Points

• 1 reply
• 4.2k views
• 1 follower

royk

October 15, 20232 yr

Hi, has any of you some experience connecting a Hifiberry Amp+ to a Tinkerboard - on Hifiberry pages this is now a possible connecting but I miss a howto and would really appreciate a quick start on this. Have previously succeed with Raspberry 3 and IQaudio - but intend to take a step further and do a project being more than just an amplifier. After testing several OS I have to admit Armbian has become my favorite and it is within this OS I hope to achieve this.

• 0

  Reputation Points

• 1 reply
• 3.4k views

Andrius ok

February 23, 20188 yr

Hallo! Habe Armbian 22.08.6 Jammy with Linux 5.15.74-rockchip mit Desktop auf "Asus Tinker Board Rev. 1.2" laufen, aber leider bekomme ich per HDMI keine stabile Verbindung. HDMI Kabel bereits getauscht (geht mit anderen Geräten einwandfrei) auch Montor getauscht (geht mit anderen Geräten auch einwandfrei). Auflösungen und Framerates habe ich durchprobiert - fehlerbild aber immer das gleiche; Bild bleibt bestenfalls ein paar sekunden ein, dann geht es wieder aus für ein paar Sekunden und das setzt sich fort. Hab ein bisschen hier im Forum recheriert und sehe das man ein "armbianmonitor -u" ausführen soll und im Forum posten: https://…

• 0

  Reputation Points

• 1 reply
• 2.6k views
• 1 follower

Werner

October 25, 20223 yr

Hi friends, I have one nagging thorn in my side that I just cannot figure out. I need someone who has a 1password account for help with this one. The problem - their desktop app and browser plugin work in tandem -- and it will not synchronize on Armbian for some reason. I've tried everything I can think of - ensuring nothing is downloaded from Flatpak and therefore sandboxed and preventing any connectivity issues. But still not working. If someone can take 5 mins and create a free trial account on 1password, then here are the steps to reproduce: Download the latest arm64 version of 1password Desktop: curl -sSO https://downloads.…

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

laibsch

July 26, 20251 yr

https://paste.armbian.com/qocicuyote.yaml <-- captured from debug UART Brand new odroid-m1, Samsung Pro Endurance 256GB; and a brand-new/uninitialized Samsung PM9A1 256GB NVMe. It drops me to a shell [presumably the initramfs]. Note: I'm not out of options yet, I can try building my own image with newer current or edge kernels. Edited to add: I think it's booting me to the petitboot env, not even attempting to boot the SD card,

• 0

  Reputation Points

• 1 reply
• 1.7k views
• 1 follower

tabrisnet

November 8, 2025Nov 8

I haven't tried Jammy with 6.1.43 but the kernel doesn't say rc anymore so curious of the status. How does this build compare in terms of feature and performance with 5.10? Is all the video decoding supported? The RK3588 Kernel support page says that hdmi audio is not supported - is that really the case? Is gnome/wayland supported? I see that only KDE is listed there.

• 0

  Reputation Points

• 1 reply
• 3.2k views
• 1 follower

Werner

April 12, 20242 yr

hai, im planning to upgrade my local media server to use an external hard drive attached using hard drive docking on USB 3.0 what I'm confused about is. what is the best FileSystem format for my hard drive? I'm not planning to unmount and use the hard drive to another PC (for example: windows PC) So I'm ready to format it with FileSystem that fully optimizes on Linux (I'm using armbian noble) so ext4 or xfs? I hear xfs is better for copying large file sizes. my casual use is downloading movies, and watching it on jellyfin. or maybe I'm just using ext4?

• 0

  Reputation Points

• 1 reply
• 3.2k views
• 1 follower

Marco Schirrmeister

August 6, 20242 yr

Hi, I am trying to make the RPI camera ( OV7750 ) to work with the TInkerboard in Armbian. But there is no module in /lib/modules for this camera. Is it already compiled in the kernel? Currently it doesn't work.

• 0

  Reputation Points

• 1 reply
• 3.4k views
• 1 follower

chwe

November 15, 20187 yr

ubuntu22 gnome desktop Hi, may I ask how to install Google Chrome

• 0

  Reputation Points

• 1 reply
• 4.7k views

Igor

November 26, 20241 yr

hi all, I am wondering if there's any reason that CEC is not built into legacy kernel for RK3399. In https://github.com/armbian/build/blob/master/config/kernel/linux-rk3399-legacy.config, module dw-hdmi-cec is not enabled. # CONFIG_DRM_DW_HDMI_CEC is not set If no special reason, I can make a PR for this. Thank you!

• 0

  Reputation Points

• 1 reply
• 4.1k views

Igor

December 13, 20205 yr

There's a strange issue with my orange pi 5 plus. When I boot into the ubuntu image, everything is fast, stable and zippy. But when I boot into the openmediavault image, it's incredibly slow. Simple operations like apt upgrade crawl. I noticed the cpu frequency is stuck at 408 MHz in htop in the openmediavault image. I ran a test. I opened another console and ran yes. Went back to htop and the frequency was still stuck at 408 MHz with one core pegged at 100% from the yes. So I fired up the ubuntu image and did the same thing. The core was at 100% but the frequency was at 2304mhz on that core. There is something wrong with the openmediavault …

• 0

  Reputation Points

• 1 reply
• 2.5k views

Mentaluproar

January 27, 20251 yr

I am trying to build armbian image via WSL 2, as I have done hundreds of times in the past. I ensured that the wsl2 distro (Ubuntu) was up to date via apt update and apt upgrade, and ran git pull was issued within /build folder prior to issuing ./compile.sh. Several files failed to download during the build including: [💲|🔨] E: Failed to fetch http://security.debian.org/dists/trixie-security/main/binary-arm64/Packages 404 Not Found [IP: 151.101.130.132 80] [💲|🔨] E: Failed to fetch http://deb.debian.org/debian/dists/trixie/main/i18n/Translation-en 404 Not Found [IP: 151.101.130.132 80] [💲|🔨] E: Failed to fetch http://deb.debian.org/debian/dist…

• 0

  Reputation Points

• 1 reply
• 670 views

Werner

August 1Aug 1

Any fixes for this? Some rock chip ICs need custom PCie overlay to set pcie speeds, maybe the kernel just has it set to gen 2? 0001:11:00.0 Non-Volatile memory controller: Micron/Crucial Technology Device 5421 (rev 01) (prog-if 02 [NVM Express]) Subsystem: Micron/Crucial Technology Device 5021 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 126 Region 0: Memory at f1200000 (64-bit, non-prefetchable) [size=16K] Capabil…

• 0

  Reputation Points

• 1 reply
• 1.9k views

laibsch

June 29, 20251 yr

How to modify the device name of a wireless network card? wlan0-> custom Gnome ubuntu22.04 help....

• 0

  Reputation Points

• 1 reply
• 1.9k views

Werner

October 13, 20242 yr

I've got a ROCK 5B+ with two NVMe drives installed, and for reasons I've not been able to track down, I'm noticing that the `-edge` releases (Kernel 6.14.6) are not able to display more than one of the NVMe drives at once. I've checked various physical configurations (i.e., slot one, slot two, both slots), and only one slot is presented (i.e., output from `lspci` or `lsblk`) – but it doesn't seem to matter whether its slot one or two. If I use a `-vendor` images (6.1.115), I see both devices and can use them without problems. I'd love to be able to provide more information or help debug, but I'm not quite sure where to start here! …

• 0

  Reputation Points

• 1 reply
• 1.9k views
• 1 follower

Werner

May 30, 20251 yr

In case anyone wondering, AIC8800D80 found in Raxda Zero 3W and Radxa Cubie A5E (aic8800 driver) supports WPA3 SAE, but not GCMP/GCMP-256 ciphers. root@radxa-zero3:~# iw phy Wiphy phy0 wiphy index: 0 max # scan SSIDs: 3 max scan IEs length: 200 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports RSN-IBSS. Device supports AP-side u-APSD. Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP-128 …

• 0

  Reputation Points

• 1 reply
• 3.6k views
• 1 follower

laibsch

August 22, 20251 yr

I have compiled with Armbian build (btw i reported that RockPro64 and Rock64 download pages give 502 Bad gateway) 1. Armbian_23.08.0-trunk_Rockpro64_jammy_current_6.1.46_minimal.img 2. Armbian_23.08.0-trunk_Rockpro64_jammy_current_6.1.46_cinnamon_desktop.img With SPI disabled, the img boots fine, but when reboot/restart takes place, board gives black screen, no U-boot activity, no white light. It will boot again after restart if reset pressed or power off/on Shouldnt board reboot normally? PS nd after u-boot log/text this screen shows prior booting

• 0

  Reputation Points

• 1 reply
• 2.7k views

2play

August 23, 20233 yr

Hello friends: I have opi5 with the spi removed, which spiloader do I use to boot from the sd card? Thank you so much

• 0

  Reputation Points

• 1 reply
• 1.8k views
• 1 follower

Werner

March 25, 20242 yr

I just installed the most recent nightly image - this one looks like a major update but it broke armbian on my opi 5 1. I had to re-install the mali firmware to get x11/wayland to start - not sure why the update deleted the file 2. I had to re-install the mali-g610-firmware rockchip-multimedia-config packages 3. VLC cannot start the h264 decoder anymore [0000005583627590] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface. Warning: Ignoring XDG_SESSION_TYPE=wayland on Gnome. Use QT_QPA_PLATFORM=wayland to run on Wayland anyway. [00000055836b79e0] main playlist: playlist is empty [h264_rkmpp @ 0x7f4cc37630] Failed…

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

OttawaHacker

February 15, 20233 yr

I have my kernel locked to 6.1.75 but still after 25.8.2 update, I lost all USB devices on both of my Orange PI 5. Only the USB3 port is working. The only way I've been able to get access to the USB is by switching to the latest `current` kernel... Any clues on what is going on? Firmware or kernel upgrades are not doing anything... where can the issue be???? I tried downgrading to many different versions but beside the current branch, USB is gone. Thanks

• 0

  Reputation Points

• 1 reply
• 1.7k views
• 1 follower

laibsch

November 11, 2025Nov 11

Hello! Has anyone tried to play straight unconverted hevc video from a GoPro 11? Iv'e tried ffplay and gst-play but I'm just getting a static image and a bunch of these errors, [swscaler @ 0x7f49d399c0] [swscaler @ 0x7f49d47a50] deprecated pixel format used, make sure you did set range correctly I have successfully played example jellyfish videos of hevc and hevc 10bit formats, ffmpeg reports the following details from the GoPro footage, Stream #0:0[0x1](eng): Video: hevc (Main) (hvc1 / 0x31637668), yuvj420p(pc, bt709), 3840x2160 [SAR 1:1 DAR 16:9], 119725 kb/s, 119.88 fps, 119.88 tbr, 120k tbn (default) …

• 0

  Reputation Points

• 1 reply
• 1.8k views

royk

July 19, 20233 yr

Hello, I am trying to create a custom uboot using armbian. it's possible? I am using the following command but I cannot generate the "uboot.bin" to save it to the spi: ./compile.sh uboot-config BOARD=orangepi5 BRANCH=current BUILD_DESKTOP=no BUILD_MINIMAL=yes BUILD_ONLY=u-boot CONFIGURATION=stable KERNEL_CONFIGURE=no KERNEL_ONLY=no PROGRESS_DISPLAY=plain RELEASE=bookworm UBOOT_ONLY=yes Thank.

• 0

  Reputation Points

• 1 reply
• 3.1k views
• 1 follower

Werner

June 17, 20242 yr

Hi, I wanted to give my Odroid M1 new life by installing a fresh Armbian 25.5.1. Previously it was running on an old Odroid Ubuntu Image. After starting from SD I have no ethernet connection. The eth0 interface is DOWN. I tried using a USB3 2.5G ethernet adapter, but the new network interface also shows DOWN. I have tried Debian and Ubuntu Minimal images with the same results. What could be the cause and how do I get a working ethernet connection? Thanks Malz

• 0

  Reputation Points

• 1 reply
• 2.2k views

Malz

June 5, 20251 yr

I have a Rockpro64 single board computer that I am trying to access remotely via an eMMC flashed Ubuntu iso image from here: https://www.armbian.com/rockpro64/, but keep getting the error message below. I was able to access the IP remotely from various laptops fine before by SSHing from the terminal, but after I failed at installing the program I wanted to install properly, I re-flashed the eMMC and have been getting this error ever since when accessing from other laptops (client-side) - I can SSH from the server-side fine with no issue FWIW. @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ IT IS POSSIBL…

• 0

  Reputation Points

• 1 reply
• 4.1k views
• 1 follower

martinayotte

August 19, 20206 yr

Can you tell me how I'm able to enable PWM? I'm not able to see any of them in the armbian-config overlay management

• 0

  Reputation Points

• 1 reply
• 2.5k views

Werner

March 28, 20251 yr

I got wierd screen blinking after update kernel from 5.8.18-rockchip to 5.9.14-rockchip. Here is blurry video with screen blinking. My screen resolution is 1600x900 and i'm using HDMI-to-VGA adapter. All was working fine with kernel 5.8.18-rockchip. I still can connect to sbc via ssh, so I checked kernel version, install old one and blinking gone: q@tinkerboard:/var/cache/apt/archives$ uname -a Linux tinkerboard 5.9.14-rockchip #20.11.3 SMP PREEMPT Fri Dec 11 22:00:29 CET 2020 armv7l armv7l armv7l GNU/Linux q@tinkerboard:/var/cache/apt/archives$ dpkg-deb -I linux-image-current-rockchip_20.11_armhf.deb new Debian package, version 2.0.…

• 0

  Reputation Points

• 1 reply
• 3.6k views
• 1 follower

jock

December 15, 20205 yr

I'm using a kernel built from sources as there's another bug which the github sources resolve. The bundled kernel with the OS image does not kernel panic. (However this image only has around a 5% chance of mounting any nvme drive) Output: Dump from 'armbianmonitor -U' https://tmpfiles.org/dl/314994/dump.txt.tar (The Armbian self-hosted system seems to be a bit moody when it wants to work)

• 0

  Reputation Points

• 1 reply
• 3.5k views
• 1 follower

jock

November 26, 20223 yr

My Orange Pi 5 with latest debian does not reboot. I use it faceless (without local screen) via RDP (LAN) from Windows, works fine. But I cannot reboot. Neither via RDP nor via SSH. The green LED stops blinking, the red LED continues. But no LAN access. Must do hard reset via button or power off/on. Any ideas?

• 0

  Reputation Points

• 1 reply
• 2.8k views

Myron

January 9, 20233 yr

I have setup the hardware acceleration as explained in the posts, but within Kodi, every now and then I can see the image with "pixelising", and looking in the syslog when this just happened, I can read: Feb 15 16:54:17 orangepi5 kernel: [ 1267.908544] mpp_rkvdec2 fdc48100.rkvdec-core: reset done Feb 15 16:54:17 orangepi5 kernel: [ 1267.908549] mpp_rkvdec2 fdc38100.rkvdec-core: resetting... Feb 15 16:54:17 orangepi5 kernel: [ 1267.908670] mpp_rkvdec2 fdc38100.rkvdec-core: reset done Feb 15 16:54:17 orangepi5 kernel: [ 1268.316705] mpp_rkvdec2 fdc48100.rkvdec-core: resetting... Feb 15 16:54:17 orangepi5 kernel: [ 1268.316855] mpp_rkvdec2 fdc48100.rkvdec-core: …

• 0

  Reputation Points

• 1 reply
• 3.3k views

Tony3

February 16, 20233 yr

I purchased the wifi + bt module. It is RTL8852BE. my armbian: Linux orangepi5-plus 5.10.160-legacy-rk35xx #1 SMP Fri Feb 2 07:51:33 UTC 2024 aarch64 aarch64 aarch64 GNU/Linux My Bluetooth never works. It cannot be listed under hciconfig: vnc@orangepi5-plus:~$ hciconfig -a vnc@orangepi5-plus:~$ rfkill ID TYPE DEVICE SOFT HARD 0 bluetooth bt_default blocked unblocked 1 wlan phy0 unblocked unblocked vnc@orangepi5-plus:/$ sudo cat /var/log/dmesg | grep "\(luetooth\|RFKILL\)" [sudo] password for vnc: [ 4.299662] kernel: Bluetooth: Core ver 2.22 [ 4.299678] kernel: Bluetooth: HCI device and connection …

• 0

  Reputation Points

• 1 reply
• 4.2k views

Werner

April 21, 20242 yr

Hi, I've been compiling my own Armbian images since 6.13-rc5, and now 6.13 and I noticed that when I compile i3, youtube videos and webgl tests don't work as great when I compile i3 with mesa-vpu as it does when I compile e.g., cinnamon. I also noticed that the suffix is not -mesa-desktop, only -desktop. Is it as per design and i3 doesn't include mesa at all, or is it some kind of bug? Thanks!

• 0

  Reputation Points

• 1 reply
• 2.2k views

ricardo_brz

January 28, 20251 yr

Note: This is for Odroid m1s, not Odroid m1 - there just isn't a forum for the m1s (yet?) When I tried to start the board with the community image for the Odroid m1s on a SD card, it wouldn't boot. The connected screen (HDMI) would stay black and the blue heartbeat LED would stay on permanently. I tried building and flashing u-boot but that didn't help me. Here's what DID work: (Note: it worked for me. I can't guarantee that this fixes it for everyone, use at your own risk) I mounted the SD card on a Linux desktop and created backups of the boot scripts (just to be safe) sudo cp <mount_path>/armbi_root…

• 0

  Reputation Points

• 1 reply
• 1.3k views

Jojo

May 19May 19

Hi, I tried to connect an external USB 3.2 gen 2x2 4TB SSD drive to the only USB-C port available on the Rockpro64, but it's not recognized. I don't know if I need to install some packages for it to work? Any help would be very appreciated! I am on Ubuntu Jammy based Armbian: 6.1.63-current-rockchip64 #1 SMP PREEMPT Mon Nov 20 10:52:19 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux It works well with the same cable on a Macbook Pro. Kind regards, Baptiste dmesg [ 4.879030] usb usb1-port1: Cannot enable. Maybe the USB cable is bad? [ 4.880111] [drm] Initialized panfrost 1.2.0 20180908 …

• 0

  Reputation Points

• 1 reply
• 2.3k views

Baptiste

January 25, 20242 yr

Linux 4.4.163 has been released since the 10th of November, but the builds on the 13th and 15th are still only showing 4.4.162. I use your builds because they're awesome, they get me the latest patches. I hope 4.4.163 is included soon

• 1

  Reputation Points

• 1 reply
• 2.8k views

Igor

November 16, 20187 yr

Hey folks... We are trying to use a DHT22 sensor on rockpro64 using armbian (buster)... Is there something we need to know about GPIO pin ? We are trying to compile and use this code as a starter... https://github.com/ayufan-pine64/dht22-pine64.git But we got a segfault when using it... thanks

• 0

  Reputation Points

• 1 reply
• 2.5k views
• 1 follower

Werner

February 8, 20215 yr

Hello, I'm trying to show a startup logo a Tinker Board without success. I tried to add a parameter logo=/boot/boot.bmp to /boot/armbianEnv.txt but it doesn't work. Is the boot logo implemented on the Tinker Board? Does it require a patch? Thanks for your feedback.

• 0

  Reputation Points

• 1 reply
• 3.7k views
• 1 follower

Igor

January 8, 20206 yr

In the most recent builds, the kernel logs have been flood with Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x8…

• 0

  Reputation Points

• 1 reply
• 2.5k views
• 1 follower

amazingfate

April 11, 20233 yr

I'm using Armbian with kernel 6.12 on a (CB2) device. When I connect my monitor via HDMI, the EDID is successfully read and it includes both 1920x1080 and 1280x800 as supported resolutions. However, only 1920x1080 appears in the available display modes. The 1280x800 mode is missing, even though it is clearly listed in the EDID.

• 1

  Reputation Points

• 1 reply
• 1.9k views

anarsoul

May 29, 20251 yr

Hello everyone, due to a project I'm working with the Friendly Elec Nanopi R4S board for which I've to use the i2c bus to read data from a sensor. Unfortunately I've not been able to access it, since the system does not recognize it. I tried with different configurations using the /boot/armbianEnv.txt file with no results, however the i2c ports are enabled. To rule out functionality problems in the sensor, I connected it to other boards (e.g. nanopi Neo3 using Armbian) without problems. Do you have any idea what could be the cause of this problem? Thanks!

• 0

  Reputation Points

• 1 reply
• 4.4k views

mef1k

October 3, 20224 yr

Hi I want to work with g_audio drivers on the usb type c otg port. When I build the image with current kernel, by applying the following overlay (I only change dr_mode to peripheral) i am able to convert the usb port in peripheral mode and successfully load the g_audio drivers and audio interfaces also come up. /dts-v1/; /plugin/; / { compatible = "rockchip,rk3588s"; fragment@0 { target = <&usb_host0_xhci>; // This matches the label in the device tree __overlay__ { dr_mode = "peripheral"; }; }; }; But when i want to do similar with the vendor kernel, which has different device tree, c…

• 0

  Reputation Points

• 1 reply
• 5.4k views

Michael Robinson

March 4, 20251 yr

Hi everyone and thank you in advance for your support! Long story short my system is in Read only mode after a reboot and I don't know what caused it. Some useful info before the reboot: I've been trying to install a RAID1 configuration so at certain point I did sudo update-initramfs -u I have manually updated and upgraded (only busybox was upgraded) with sudo apt update && sudo apt upgrade If you need any other info let me know! EDIT: I found out that I'm able to manually mount the root partition, but the problem persist after each reboot. I then added the follong to /boot/armbianEnv.txt extraargs=fsck.…

• 0

  Reputation Points

• 1 reply
• 3.4k views

Račka

August 17, 20242 yr

Board is RockPro64, legacy kernel - 4.4.213-rockchip64. The issue is this: [ 1451.681339] ohci-platform fe3a0000.usb: frame counter not updating; disabled [ 1451.681972] ohci-platform fe3a0000.usb: HC died; cleaning up [ 1451.682516] usb 8-1: usbfs: usb_submit_urb returned -19 [ 1451.682569] usb 8-1: USB disconnect, device number 2 It happens only on the USB2.0 ports with different keyboards, mice, custom USB HID device, webcam. The other 2x USB 3.0 ports are working fine with the same devices. Tried fixes so far - turning usbcore.autosuspend option off, adding usbhid.quirks for every device. extraargs=usbcore.autosuspend=-1 usbhid.qu…

• 0

  Reputation Points

• 1 reply
• 3.5k views

Pencheff

December 19, 20205 yr

I was happy to find the Orange pi 4 armbian; it ignores raspbian an ubuntu images on sd and boots into android from its EMMC instead. The pi is an orange 4 LTS with 3gb RAM and 16gb EMMC. I have a 2tb crucial SSD attached through the usbc port. It is powered by a 4A supply through the DC port. it's purpose is to be a dedicated mythtv back end; it is wired by ethernet but also has wifi active. armbian-hardware-monitor.log is at https://paste.armbian.com/axayequliz it isn't showing up as a disk, as near as I can tell: the first is the EMMC, I believe, and the second my sandisk car…

• 0

  Reputation Points

• 1 reply
• 3k views
• 1 follower

dochawk

February 11, 20233 yr

I wanna use tinker board to work with logitech c930e camera. when i use cheese to open camera in tinker board. it's just show one black picture, and the camera light is on. before i had use the nanopi m4 to work with the logitech c930e. it's working good. and m4 create /dev/video0 , /dev/video1. but tinker board just create /dev/video0, so i think it maybe inside kernel have some option not open. but i don't know which need open. i'm not good at kernel. can give me some help? thanks a lot

• 0

  Reputation Points

• 1 reply
• 3k views

aitek

December 15, 20187 yr

Hello, I have Tinker Board. If I install Armbian I see screen only over HDMI. I would like to enable DSI touchscreen display. Is it possible? How make it? Thank you

• 0

  Reputation Points

• 1 reply
• 4.8k views
• 1 follower

TonyMac32

June 25, 20179 yr

I bought a Tinkerboard S and Tinker Aluminum case yesterday, but because of the case, it's Wifi function is almost non-exist, so I bought a TP-LINK TL-WN722N v2 two hours ago. I was hoping to get a V1, which has a lot of information on Wikidevi, and looks like it's going to work out-of-the-box, but I got a v2, and now I'm trying to get it to work. Wikidevi provided a link to driver repository, I downloaded main branch and type "make all" in terminal, it says /lib/modules/4.4.166-rockchip/build does not exist. I tried to search how to install kernel header and tried this command "sudo apt-get install linux-headers-$(uname -r)", it doesn't work/help. …

• 0

  Reputation Points

• 1 reply
• 4.2k views

axzxc1236

January 16, 20197 yr

My orange pi 5 armbian Os isn’t displaying hdmi output to my monitor. However, it works on my flat screen tv, any reason why this might be ?

• 0

  Reputation Points

• 1 reply
• 1.9k views

Catloaf2019

April 17, 20233 yr

I haven't been able to find a step-by-step for enabling a USB OTG Network on the RockPi-S. Anyone have a link to the steps? I'm referring to the ability to connect a USB cable between the RockPi-S and a computer and be able to ssh or network to it. My usb port is in peripheral mode and I'm using Network Manager on Armbian Bookworm.

• 0

  Reputation Points

• 1 reply
• 2.3k views

Meestor_X

March 29, 20251 yr

I just testet all available stable armbian images with radxa zero 3e. when i turn off the machine with shutdown -h 0 or poweroff the system shuts down successfully but the power of the dc dc is not turned off. the 3.3V is still available. i dont know if its only a configuration mistake or a bug. normaly after a kernel shutdown, the driver for rk817 should send i2c package to reset the 817. after that you need a power cycle to recover and restart. https://paste.armbian.com/inibopomew br manuel

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Pulsares GmbH

October 2, 20242 yr

Hello I built the core minimal image successfully a few times while I was experimenting with kernel config options and then finally when I enabled all the settings I wanted somehow a different component of the build process started failing repeatedly since last few days: Why is this happening. All I did was edit linux-rockchip-rk3588-edge.config and symlink linux-rockchip-rk3588-current.config -> linux-rockchip-rk3588-edge.config

• 0

  Reputation Points

• 1 reply
• 541 views

Werner

August 17Aug 17

Is there an official way of installing libmali drivers on Armbian? I'm feeling a bit slow, since I can't really figure out how to install them. It seems like files from this github repo will overwrite other system files, so it's not a solution that would work in the long term.

• 0

  Reputation Points

• 1 reply
• 5.9k views

JMCC

February 16, 20188 yr

Hello Everytime I reboot I have to wait many minutes before the NIC auto-negotiates and connects. The problem seems to be at the PHY layer as the LED does not light up at all ... see time span between 23:22:20 and 23:23:52 : Why is this happening? Only enP3p49s0 is plugged in and NetworkManager-wait-online.service is disabled. Thanks

• 0

  Reputation Points

• 1 reply
• 628 views

usual user

August 18Aug 18

Hi I need help, I have used in the past the Banana PI M1 card for many years with a SATA Port Multiplier. To enable PMP support for this card, you had to edit: nano /boot/boot.cmd Go to line that starts with: setenv bootargs and add at the bottom of the row: ahci_sunxi.enable_pmp=1 recompile with: mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr Restart Almbian and the SATA Port Multiplier was activated. I now own a RockPro64 with Armbian and a 6-port PCIE sata card. Should buy a card with 8-10 ports to add hdd that I will need to make backups. …

• 0

  Reputation Points

• 1 reply
• 3.3k views
• 1 follower

DBSD

August 2, 20206 yr

I used sudo swapoff -a as suggested in this thread: but the setting isn't persisted, and upon reboot sudo swapon --summary shows a partition There's no "swap" text in my /etc/fstab I'm trying to install Kubernetes, so I need to disable swap.

• 0

  Reputation Points

• 1 reply
• 4.5k views

trip

April 10, 20206 yr

Hello ! Not found any devices How to make it work? hciconfig -a hci0: Type: Primary Bus: USB BD Address: E8:48:B8:C8:20:00 ACL MTU: 1021:6 SCO MTU: 255:12 UP RUNNING PSCAN RX bytes:1537 acl:0 sco:0 events:148 errors:0 TX bytes:3430 acl:0 sco:0 commands:136 errors:0 Features: 0xff 0xff 0xff 0xfe 0xdb 0xfd 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH HOLD SNIFF PARK Link mode: PERIPHERAL ACCEPT Name: 'orangepi5' Class: 0x000000 Service Classes: Unspecified Device Class: Misce…

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Michael Robinson

March 22, 20242 yr

Which Os does support hardware encode h264\h265 ? Or where i can read about status supporting hardware encoding for video (h264\265) and image (jpeg) ? chip: RK3288

• 0

  Reputation Points

• 1 reply
• 3k views

TonyMac32

January 18, 20197 yr

Sir, I have Purchase the Tinker board before 20 days, I install the Armbian 5.35 version in the Board, All software are very Nicely Work , but could not connect audio , I am trying to the 10 more times reinstall the Armbian 5.35 version but could not connect the audio output in audio 3.5mm Jack , I will so tired please solve this Problem in my tinker Board …

• 1

  Reputation Points

• 1 reply
• 3.9k views
• 1 follower

TonyMac32

January 25, 20188 yr

i'm stuck with this since day 1 but now i upgraded to armbian (with kodi-gbm) i had this problem worse stress testing the board with stress -c 4 doesn't bring the board into shutdown, but logging in to kodi-gbm or using graphical interface? it brings instability all of a sudden. there's no inherent pattern from the shudowns except when i launch kodi or access some files (emby transcoding doesn't cause any instability). anything outside the text mode should cause it to shutdown. weirdly enough, when i removed the USB peripherals (2xUSB HDD, own power supply for both cases) the instability worsens and doesn't boot or sometimes reboot cycle after fsck.ext4 on sta…

• 0

  Reputation Points

• 1 reply
• 3k views
• 1 follower

xAda

January 13, 20233 yr

I have the latest armbian 6.1.75-vendor-rk35xx (ubuntu with gnome desktop) installed and everything works perfectly except that some videos are hanging in chromium. In dmesg I get [23230.260311] [drm:rockchip_vop2_mod_supported] *ERROR* Esmart0-win0 unsupported format modifier 0x800000000000351 and then boom, the whole thing stops playing and hangs. No other error anywhere. This happens with specific mp4 videos on specific frames. Any suggestions?

• 0

  Reputation Points

• 1 reply
• 2k views
• 1 follower

ArmBoy1988

October 7, 20242 yr

Hi, since i have a Asus tinkerboard incoming i was wondering if anyone knows if the "generic" arm64 distro will work this board. Its based of the rockchip RK3288 SoC The support pages states that the board supports debian, but since i dont need a UI ect (im going to use it headless) i dont need the board to load a ui into memory and wanted to use a normal build instead of the TinkerOS Please note, my knowledge of the inner workings of *nix is quite limited, so if my question is to generic or imprecise i apologize.

• 0

  Reputation Points

• 1 reply
• 5.1k views

Igor

October 11, 20206 yr

I am trying to compile the Kernel on my PC with the Ubuntu recommended version. I get the error below: arch/arm/dts/rk3128-evb.dtb: Warning (avoid_default_addr_size): Relying on default #address-cells value for /syscon@20008000/usb2-phy@17c arch/arm/dts/rk3128-evb.dtb: Warning (avoid_default_addr_size): Relying on default #size-cells value for /syscon@20008000/usb2-phy@17c FATAL ERROR: Couldn't open "./u-boot.dtb": No such file or directory ./tools/mkimage: Can't read u-boot.itb.tmp: Invalid argument make: *** [Makefile:1053: u-boot.itb] Error 255 Any idea what this could be? It is the first time I am running ./.compile.sh potential…

• 0

  Reputation Points

• 1 reply
• 3.1k views

Werner

February 7, 20233 yr

I only have options 1,4,5,7 on my nand-sata-install utility and can only boot from a single armbian microsd card but no other. /dev/mtdblock0 shows no files. Everything has been fine till now! Would love some help. Thanks

• 0

  Reputation Points

• 1 reply
• 1.7k views

Werner

January 24, 20242 yr

There's a few problems with the UART driver on 5.0-rc2 kernels, since proper checks are not done correctly and lead to a Null Pointer dereference. Here's a patch to avoid this issue : From 7e43ae8446b420907f00b43308ad0b99b6fe4e51 Mon Sep 17 00:00:00 2001 From: "Miouyouyou (Myy)" <myy@miouyouyou.fr> Date: Wed, 16 Jan 2019 23:58:52 +0100 Subject: [PATCH] drivers: tty: serial: Bail out if no UART is detected Before the 5.0, serial8250_register_8250_port consisted of one BIG if(uart && uart->port.type != PORT_8250_CIR) block, which prevented NULL dereference if uart, a pointer to an "uart_8250_port" detected through "serial8250_find_ma…

• 0

  Reputation Points

• 1 reply
• 2.5k views

Myy

January 17, 20197 yr

Hello everyone I was trying to look for information in the forum but I can't find any topic where this specific issue is discussed. I also looked for help in the omv forum and they told me it was a problem with the distribution, hopefully you can help me. My system running Armbian_24.5.1_Orangepi5-plus_bookworm_vendor_6.1.43_minimal Install OMV, omv extras, i try to configure the compose folders and i get the 500 internal server error, clear cache, update and reboot system but there is no change, a moderator asked me for the log by executing the following command "Your error output is incomplete. What is the output of: sudo omv-salt …

• 0

  Reputation Points

• 1 reply
• 5.8k views
• 1 follower

Manuel Carvajal

June 18, 20242 yr

Hello people, I have an Asus Tinker Board S and decided to use the Mainline Armbian for this board, love the new panfrost driver but seems it is glitching all over the place, icons in the menu disappear and reappear when mouse hovers over them, tick boxes do not show if they are ticked and only flicker when mouse is over them and applications menu keep redrawing all over when trying to use among the most prominent problems. Other operating systems work well in this matter. Anyone else is having these problems with the mainline 5.4.28 kernel build?

• 0

  Reputation Points

• 1 reply
• 3.5k views

Nikos Giannakas

June 10, 20206 yr

Hi all, I’m new to this whole SBC thing, and I recently got an Orange Pi 5. I first installed the official OS (Ubuntu), where I needed to do into orangepi-config and go into System > Hardware > wifi-ap6275p and enable that to use the official M.2 WiFi dongle. However, I don’t see this option on Armbian. Does it not support it?

• 0

  Reputation Points

• 1 reply
• 2.9k views
• 1 follower

Igor

February 18, 20233 yr