Amlogic meson

Hi! Using the vanilla ARMBIAN image 23.02.2_Bananapim5_bullseye_current_6.1.11_minimal Enabling the provided uartA and uartC dtbos fails. Here is the output from the boot process, as captured via the Serial Debug interface: 238 bytes read in 3 ms (77.1 KiB/s) Applying kernel provided DT overlay meson-uartA.dtbo failed on fdt_overlay_apply(): FDT_ERR_NOTFOUND 238 bytes read in 3 ms (77.1 KiB/s) Applying kernel provided DT overlay meson-uartC.dtbo failed on fdt_overlay_apply(): FDT_ERR_BADMAGIC It seems that this image provides invalid dtbos, likely not properly built alongside the same kernel image. I'm happy to help de…

• 0

  Reputation Points

• 3 replies
• 5.9k views
• 1 follower

PikaBZH

April 22, 20233 yr

I have an odroid-c2 with eMMC module flashed with Armbian_23.02.1_Odroidc2_jammy_current_6.1.14_xfce_desktop When viewing youtube containing word composed of non-latin characters, it shows a funny symbol for each character. How do I install the proper language for this?

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

dev001

April 19, 20233 yr

I have an odroid-c2 with eMMC module flashed with Armbian_23.02.1_Odroidc2_jammy_current_6.1.14_xfce_desktop I have the following connected to the USB ports. 1) USB to audio headphone/microphone jacks 2) Wifi keyboard dongle The odroid-c2 is connected to an HDMI monitor with speakers I've been manipulating the settings for Pulseaudio and I could not get the audio to output to the monitor speakers. I could hear audio from the USB to audio jack connected to headphones

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

dev001

April 18, 20233 yr

I tested the latest available Armbian image (minimal installation) on my odroid C2 via SD card. have available an 16gb hardkernel emmc card on which I had ubuntu 20.04 installed and running. But by burning the image with etcher (the same procedure as with the SD image) the odroid is unable to boot. Black screen, solid red led, and nothing else. I waited more than 30 seconds, I tried to disconnect keyboard....I waited more than 30 seconds, I tried to disconnect keyboard I have repeated the procedure through the SD and it works correctly. When I do it through the emmc, the system does not boot. When I use the SD card, the Emmc card is ob…

• 0

  Reputation Points

• 0 replies
• 2.7k views

pirsen

April 17, 20233 yr

Hello, I know this is a forbidden question, I will adress specially to @chewitt and @Igor. Why I dare to do this? Because today, it is the fist time I managed to run Libreelec (LE) nighly https://test.libreelec.tv/11.0/Amlogic/bananapi-m5/ and have the somehow the same suffering with boot and so on and as I did not give up, I shot the last bug preventing LE to boot. I don't want to register in every forum for each pack , christian forgive me I will put the explanation here. The last image suffer from a missing link..in /flash as it is all momified in squashfs , this need extra skills. wget https://ftp.halifax.rwth-aachen.de/libreelec/L…

• 0

  Reputation Points

• 4 replies
• 4.6k views
• 1 follower

SoSie

April 17, 20233 yr

After updating my Odroid N2+ today, lo is the only network interface shown when running 'ip a' The update was 18 packages: root@odroidn2p10:~# apt upgrade Reading package lists... Done Building dependency tree... Done Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: armbian-config armbian-firmware armbian-zsh libldap-2.5-0 libldap-common libnss-myhostname libpam-systemd libsystemd0 libudev1 linux-dtb-current-meson64 linux-image-current-meson64 linux-u-boot-odroidn2-current python3-tz sudo systemd systemd-sysv tzdata udev 18 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to g…

• 0

  Reputation Points

• 3 replies
• 4.4k views
• 1 follower

MarkP

April 15, 20233 yr

I need a UART in my work. Added uartC overlay via armbian-config (UART_EE_C - /dev/ttyAML4) However, after booting, the device /dev/ttyAML4 does not appear. The download log contains the following information: Using the kernel-provided DT meson-uartC.dtbo overlay fdt_overlay_apply() error: FDT_ERR_BADMAGIC base fdt has no node /__symbols__ make sure you compile with -@ Error applying DT overlays, restoring original DT I would be grateful for any help!

• 0

  Reputation Points

• 0 replies
• 2.3k views

diaamant

April 12, 20233 yr

Hello, I was running OpenMediaVault on Armbian Buster some time ago and after an update (I suppose) the system would not boot normally anymore. Had to move places shortly after that, so the board stayed in a box for about a year and now I would like to put it back into service. A Bullseye image is required for OMV 6, so I went to the website and downloaded the latest image for my Odroid N2 board : Armbian_23.02.2_Odroidn2_bullseye_current_6.1.11.img.xz I then flashed the 16GB eMMC and plugged it in ... no boot (fixed red led / no network) If I do the same with an SDCard, it boots up normally (blinking blue led / working SSH) …

• 0

  Reputation Points

• 2 replies
• 4.1k views
• 1 follower

Kahana82

April 7, 20233 yr

Hi Everyone, I'm trying to get audio out of my N2+ via SPDIF on the 7 pin header, or any gpio pin if necessary. So far I have confined my SPDIF output works with the official Odroid MATE image, and also that I can get audio out via the 3.5mm jack on armbian after flowing this post . I have tried to understand the amixer wizardry but no luck achieving anything so am a bit stuck as I would really like to use armbian over the Odroid image. Thanks for any help!

• 0

  Reputation Points

• 1 reply
• 3.5k views

jmccoy555

April 6, 20233 yr

hello everyone, can anyone tell me how to install the driver for the RTL8811 WiFi USB dongle?

• 0

  Reputation Points

• 3 replies
• 5k views
• 1 follower

elsabz

April 3, 20233 yr

Is there a way to enable the audio jack? Only the HDMI audio is working.

• 0

  Reputation Points

• 5 replies
• 9.5k views
• 1 follower

jmccoy555

March 31, 20233 yr

I'm trying to complete the installation of Armbian onto the HC4 (HC4-P if that changes anything). With a fresh SD card I run sudo dd if=Armbian_22.11.1_Odroidhc4_bullseye_current_5.19.17.img of=/dev/sdb status=progress plug in the card to the board, plug in the ethernet cable, hold down the boot switch, and plug it into power. It all seems to run correctly: I can SSH into the board and I complete the initial steps to set-up the installation (root pass, default shell, username, real name, and locale). However it does not seem as I can access the SPI FLASH device. Running the following commands from the HC4 page do not work as there are no mt…

• 1

  Reputation Points

• 8 replies
• 7k views

eacton

March 30, 20233 yr

I'm testing the Armbian image for Odroid N2+ ( Armbian_22.08.7_Odroidn2_jammy_current_5.19.17_xfce_desktop) to see if it's a good migration path from the HardKernel base image. Unfortunately I need to get both i2c bus running on the GPIO and so far only the first bus seems to work (i2c-0). Looking into /sys/bus/i2c/devices , it looks like i2c-1 is tied to the hdmi port instead of the 2nd i2c bus on the GPIO : lrwxrwxrwx 1 root root 0 Dec 31 1969 0-0051 -> ../../../devices/platform/soc/ffd00000.bus/ffd1c000.i2c/i2c-0/0-0051 lrwxrwxrwx 1 root root 0 Dec 31 1969 i2c-0 -> ../../../devices/platform/soc/ffd00000.bus/ffd1c000.i2c/i2c-0 lrwxrwxrwx 1 root …

• 0

  Reputation Points

• 4 replies
• 5.6k views
• 1 follower

Alda

March 30, 20233 yr

Hi, I have a odroid n2+ and I want ask, how to enable UART on the pin8 and pin10 ? Normaly it's mapped as ttyAML1 but this is now missing. I found some informations about /boot/armbianEnv.txt, but I'm not well experienced so I don't want beak a OS. Please can you help me what to modify to get UART working ? Thank you for help

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

Alda

March 30, 20233 yr

Hi, I'm trying to use an external RTC clock (https://www.hardkernel.com/shop/rtc-shield/, battery is good) connected over I2C to wakeup the Odroid HC4 from poweroff (or if not possible from disk-suspend). To my surprise the rtc was already recognised (and also the device tree seems good) and I'm able to communicate with it, read it and set alarms for it. However, whenever I poweroff the device and try to turn on again it does not power on by itself (neither from poweroff, nor from disk suspend). Output from /proc/driver/rtc: rtc_time : 19:16:28 rtc_date : 2023-03-29 alrm_time : 19:07:00 alrm_date : 2023-04-29 alarm_IRQ : no alrm_pending : no upd…

• 0

  Reputation Points

• 0 replies
• 3.5k views

trembel

March 29, 20233 yr

Hello, I have tested Armbian with SD card without issue. I'm wondering if it's possible to do the same using SSD. SSD is much more reliable and faster than SD card. I can do it with the Ubuntu release from Odroid using petitboot, but it seems that Armbian isn't compatible with petitboot. Thank you

• 0

  Reputation Points

• 73 replies
• 49.6k views
• 2 followers

-hannes-

March 25, 20233 yr

Armbian_22.08.7_Bananapim5_bullseye_edge_5.19.16_gnome_desktop Hello, I'm trying to rotate the desktop from landscape to portrait. Trying to do this in the display settings in the desktop does not work correctly as it only uses the top half of the screen. What does work is to rotate using xrandr: xrandr -o right I'm trying to do this automatically on start up so I have written a script to call from lightdm.conf The script: #!/bin/sh xrandr -o right exit 0 The parts in lightdm.conf [Seat:*] that I've edited: display-setup-script=/home/badger/screen.sh session-setup-script=/home/badger/screen.sh This w…

• 0

  Reputation Points

• 6 replies
• 5.3k views

SoSie

March 20, 20233 yr

I want to use a StromPi3 board with my lepotato board. I am using the armbian image. I used armbian-config to enable the serial ports and both show up as /dev/TTYAML0 and /dev/ttyAML6. Nonetheless I am unable to communicate on the serial ports even when connecting jumpers and a USB serial converter. I later tried to modify the divorce tree by hand. No change. Is there something else I could try to get the serial port on pins 8 and 10 working?

• 0

  Reputation Points

• 0 replies
• 2.2k views

NeoCortex97

March 19, 20233 yr

Hello, I’m in a pickle. I bought an Odroid HC4 a few months ago, setup a RAID-1 array and installed Nextcloud on it. At the time, I used `nand-sata-install` to move the system from the SD‑card to a partition of one of the HDD (/dev/sda1), out of RAID (/dev/md0), and leave the bootloader on the SD-card. I did not make a backup of this SD-card and, after rebooting today, I realised the SD-card was not functioning any more. No device I use (Sansa audio player with Rockbox, phone with Ubuntu Touch, Laptop with Ubuntu) would even detect it. I was thinking of using `nand-sata-install` again to only update the bootload…

• 0

  Reputation Points

• 0 replies
• 2.6k views
• 1 follower

arkhi

March 18, 20233 yr

Hi there! I've installed Armbian 23.02.0 Jammy on my Banana Pi M5. And I'm using 3.5" display with HDMI interface. The screen has a native 480x320 resolution, but accept a range from 640x480 to 1920x1080. On resolutions over 800x480 is not readable, so I'm able to change resolution with the following line in /boot/armbianEnv.txt extraargs=video=HDMI-A-1:800x480M@87 fbcon=rotate:0 with lower resolutions 800x480 to 640x480 (60 to 87hz) the screen has an offset down of one character line so ther's a blank line up and I don't see login and shell input command down. Looking at 16:9 resolutions I see all the text with the minimum of 896…

• 1

  Reputation Points

• 3 replies
• 5.1k views
• 1 follower

Mechano

March 17, 20233 yr

Hello all! I have an ODROID-C2 that I am trying to use with a GPS connected over UART for timing purposes, which requires the use of pps. Based on my searching and reading in this forum, I have determined that for my OS and kernel (Focal, 5.9.14) I should be able to do so by adding overlay=pps-gpio to armbianEnv.txt. What is not clear to me, however, is how to specify which pin to use! In this thread I see windysea said: But I don't know how to use this information! I have found no documentation on param_pps_*, and my attempts at guessing based on information from other threads and resources have failed to work so far. I have been fiddling…

• 1

  Reputation Points

• 8 replies
• 7.2k views
• 1 follower

Jeffsf

March 16, 20233 yr

Hello, The mission: to change display resolution for "None-1" ('unknown display') - when no physical screen/display/monitor is attached. Machine: Banana Pi M5 (Bpi M5). I use it as a headless machine (without any monitor connected) and access it via a remote control/share screen application (such as: Teamviewer). The problem: the display is very small as the resolution is set to 720 X 576. I couldn't find any way or method to define/change the resolution in such a case. How can this be done? I'll appreciate any assistance you can provide. Thanks in advance! This is the information of the machine and Armbian version installed…

• 0

  Reputation Points

• 4 replies
• 10.5k views

SoSie

March 16, 20233 yr

As the original thread, which was closed by moderator for obvious reason, did attract attention of few peoples having the same problem as me, it would be a waste not to follow up on this, I think. Let me sum up: I have two HC4, one bought in 8.2021 and other one 11.2022, both have two SSDs each. The older one after a kernel upgrade didn't see a second disk any more. I've just tried few kernels I could find with the following results: OK: Linux odroidhc4 5.12.10-meson64 #21.05.4 SMP PREEMPT Wed Jun 16 08:19:35 UTC 2021 aarch64 aarch64 aarch64 GNU/Linux OK: Linux odroidhc4 5.13.12-meson64 #21.08.1 SMP PREEMPT Wed Aug 25 19:35:13 UTC 2021…

• 1

  Reputation Points

• 5 replies
• 4.3k views
• 1 follower

ChrisO

March 1, 20233 yr

Hello, I've got a Le Potato, and a Tritium (I like the Tritium better, but I "feel" that Le Potato is a little bit quicker for longer). I've had them for about a week, I am a daily *nix user, and run several RBPi's around my home - 3D printers, Motion Cameras, Christmas Lights, and one is even a back up web server. My notebook runs Arch, my server runs Gentoo, and my workstation usually runs RebornOS or ZeroArch depending on my mood). When I started using these Libre Boards, I was happily impressed but using them as a desktop (my intention is/was to get my kids a 3D printer, and use these to do double duty as slicers, and basic desktops (I've got a…

• 0

  Reputation Points

• 0 replies
• 2.6k views

67Comet

February 27, 20233 yr

Hello, I'll start by saying I'm new at those things. I have recently bought a "Le Potato" board. I was trying to install Lakka (via raccomanded link). When I plugged in the micro SD, the power, the HDMI out ecc, nothing happened other than two led turning on (red and blue). What could have gone wrong? Thanks in advance

• 0

  Reputation Points

• 1 reply
• 2.8k views

NicoD

February 22, 20233 yr

Hello, I got a BPIM5 with rtl8822cs board and a BPIM2+ with internal wifi chip for home automation. I started my project (vpn gateway) with the ubuntu server distribution on BPIM5. I had a lot of instability of the wifi driver (lost of station in AP mode) and and the board crashed every two, three days. I switches to ARMBIAN with the last Armbian 22.11.3 Bullseye with Linux 6.1.4-meson64. This software seems to work fine on M2+ and wifi is fine and stable. So I tried to move my M5 to the same level. The M5 boot on sd card, I move it on MMC memory and the board boot . Unfortunatly the wifi board (rtl8822cs sdio) is not recog…

• 0

  Reputation Points

• 7 replies
• 6.8k views
• 1 follower

glambert

February 18, 20233 yr

Hi have two N2s (an N2+ and N2). Both are connected to a Viewsonic 2560x1440 2 HDMI ports monitor where they both work well. One system (N2+) is running Ubuntu 22.04 the other is running Armbian jammy 22.04.01 Kernel 6.0.13 #22.11.2. I have purchased a ATEN CS22H 2 port HDMI/USB KIVM switch. When I connect both systems to the monitor via the KVM I only get a picture from the Ubuntu system. The Armbian system is always black. Can I force the kernel/firmware to be 2560x1440x60hz. I was looking at this post : Regarding forcing the kernel to be a fixed resolution but wasn't sure it was relevant. …

• 0

  Reputation Points

• 2 replies
• 3.2k views

Igor

February 13, 20233 yr

Hi everyone, I'm using Radxa Zero HW version 1.4, 4GB RAM with 64GB eMMC. I used long time armbian on SD card. I decided to install MMC for better performance but armbian crashes APT involving stuffs. By the way, I'm using Rzero with headless and connecting via SSH from Win11 machine. I installed with producer tools directly writing image to MMC and alternatively installed with armbian-config tool from SD card to MMC. In both way successfully boots and connects Wi-Fi. For better diagnostic, how can I get error dump? (I lost SSH connection when its crushed).

• 0

  Reputation Points

• 0 replies
• 2.3k views
• 1 follower

erturk47

February 11, 20233 yr

Hi guys, My N2+ just arrived and I was able to install a Debian Bookworm (EDGE) image I built onto it (both to a SD card and an EMMC card) The selector switch is set to boot from MMC. Armbian fires up nice from the SD card but it does not boot from the EMMC. I can see the Drive with fdisk so I guess I need to copy the boot image onto it. (Its /dev/zram1) This is the first step towards building a PREEMPT_RT image so I was excited to see it sorta works! Any help or ideas would be appreciated.

• 0

  Reputation Points

• 1 reply
• 3.2k views
• 2 followers

rodw

February 10, 20233 yr

Hi, I am new to Armbian and I am working with the Jammy Minimal CLI image (9 Jan 2023) in a Banana Pi M5. I need to configure the w1 to the pin GPIOA_14 and I have tried adding the following to /boot/armbianEnv.txt: overlays=w1-gpio param_w1_pin=GPIOA_14 But it does not work. How should I configure it? Thanks

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

Liverio

February 8, 20233 yr

I was trying to route my audio from HDMI to the 3.5mm stereo jack. Tried playing with various knobs on alsamixer (like what you could do on the Raspberry Pi), but couldn't get the audio to switch. Looking into the DTS, it seemed like there was consideration made for analog audio ( e.g. analog-amplifier). Was this ever working?

• 1

  Reputation Points

• 11 replies
• 12k views
• 3 followers

MichaIng

February 7, 20233 yr

Hey, I have a very similar problem here to this and this thread. I rebooted as the HC4 was already bugging me for a while to reboot on the motd (unattended-upgrades). Since the reboot, /dev/sdb is gone. It's a new Samsung SSD 870 EVO as well as in the other thread. The other (still running) one is a new Crucial MX500. I tried several Armbian kernels but no change. I went back to 5.10.57-meson64. There are no obviously burnt components on the device. There seem quite a few people with this problem. Any ideas? Thanks a lot! P.S. TP10 and TP11 are at 12V.

• 0

  Reputation Points

• 4 replies
• 3.1k views
• 2 followers

Autic

January 31, 20233 yr

Hi, This is my first try to add a board to armbian build system. I got a BPI M2S since several months, but only had time recently to investigate on this promising SBC. I made a PR here, if somebody wants to try it: https://github.com/armbian/build/pull/4597 The main improvements are to be done for the dts file, since I'm not an expert about such file definition. Only 1 ethernet of the Gbit ports is working, since I copy the config from vim3 that share the same hardware for it. I didn't try to customize u-boot and I use the one for radxa zero2 that works to launch armbian on the board. armbianmonitor -u is here: https://paste.armbian.co…

• 0

  Reputation Points

• 7 replies
• 5.1k views
• 1 follower

jeanrhum

January 25, 20233 yr

The zfs-dkms included in Armbian_22.11.1_Odroidhc4_jammy in version 2.1.4 is to old for 5.19.17 kernel. It should be 2.1.6 like in Armbian_22.08.7. Loading new zfs-2.1.4 DKMS files... Building for 5.19.17-meson64 Building initial module for 5.19.17-meson64 configure: error: *** None of the expected "blk_queue_discard" interfaces were detected. *** This may be because your kernel version is newer than what is *** supported, or you are using a patched custom kernel with *** incompatible modifications. *** *** ZFS Version: zfs-2.1.4-0ubuntu0.1 *** Compatible Kernels: 3.10 - 5.17 http://paste.debian.ne…

• 1

  Reputation Points

• 4 replies
• 3.6k views

drikus

January 24, 20233 yr

Hi everyone! For about a week now, I have been using armbian 22.11.1 on my new Odroid HC4, which is my Nextcloud server. As alway, armbian is rock solid 😉 I have just a little question: Can one modify the information presented in htop? I'd like to have "CPU temperature" and "TX today" (meaning sent bytes) showing. The welcome screen already shows "CPU temperature" and "RX today". I know that the CPU temperature can be read here /etc/armbianmonitor/datasources/soctemp and but I can't find it in the htop-configuration under "available meters".

• 0

  Reputation Points

• 0 replies
• 2.3k views

berobispo

January 18, 20233 yr

I'm using the "Armbian 22.11.1 Lepotato jammy 5.19.17 xfce desktop" image which comes with lightdm windows manger and wayland xserver. I want to use https://github.com/debauchee/barrier but it does not support wayland, so I want to switch to xorg. So far I've tried installing xorg using apt and adding the following line to /etc/lightdm/lightdm.conf xserver-command=Xorg but when I do sudo systemctl restart lightdm the display manager hangs forever with blank screen and blinking cursor.

• 1

  Reputation Points

• 1 reply
• 4.2k views
• 1 follower

XENIZS

January 8, 20233 yr

Armbian keeps showing yellow/green/blue/green-blue screens instead of the login menu. It will show the Armbian booting screen and the terminal for a second then when it should show the user login, it doesn't. I have used it properly before, but after a restart it starts doing this.

• 0

  Reputation Points

• 3 replies
• 2.9k views
• 1 follower

atone

January 7, 20233 yr

Hello there! Are there any webcams that the Le Potato supports on Armbian? Thanks for the assistance!

• 0

  Reputation Points

• 1 reply
• 3.2k views

Werner

January 7, 20233 yr

Hello everyone! I bought Khadas VIM1 board and Official FAN(Ali Link) but seems to be not working with Armbian Bullseye, how I can run it? Thanks.

• 1

  Reputation Points

• 8 replies
• 5.4k views

noisyislands

January 6, 20233 yr

Hi there, I have new HC4 (like 6 moths old) and since beginning I am struggling with reboot. I have latest Armbian Bullseye, and every time I make reboot, I need to power cycle to get it up. Is there any solution to that problem? I tried HK images, and they are rebooting but they are old so I want to be a bit modern but that is really annoying issue. Any help please? And Merry Christmas guys, thanks for the awesome distro even with that stupid problem.

• 0

  Reputation Points

• 2 replies
• 2.7k views

Relocated2007

December 31, 20223 yr

I have a bunch of these boards and a few friends that would like to use them. I am having problems getting UART on the GPIO to work even using Libre Computers Wiring tool. Is there any info on getting Armbian Device Tree Overlay to work with the potato? I really need UART on the GPIO. CAN0 would be a very helpful creature comfort but if i cannot get UART to work properly i have extremely dwindling odds of getting CAN0 to function properly. Any info that can point me in the right direction is welcome.

• 0

  Reputation Points

• 1 reply
• 3k views
• 2 followers

Brad Wigton

December 30, 20223 yr

Hi there, I have two Le Potatos, one for each of my boys. One of them has Raspbian OS on it and the other has Armbian. What we have found is that the one with Raspbian is able to run Scratch (https://scratch.mit.edu/), but the one that I have loaded with Armbian gives an error that says that WebGL is not working properly on Chromium. On Firefox I don't get an error, but Scratch doesn't work right. I purchased these on the same day, so as far as I know, the hardware should be the same. Is there a way to enable WebGL on Armbian so that my boys can use Scratch on this system? In case it helps: https://paste.armbian.com/wepugikade

• 0

  Reputation Points

• 5 replies
• 3.9k views

TonyMac32

December 18, 20223 yr

board ist lafrite with 512mb, 8gb emmc tried all possible ports for i2c. first by configuring with armbian-config and activating i2c port a and b. then manual by writing an overlay to activate i2c_ao and deactivate the uart on pins 3+5; also tried pins 27+28; i2cdetect -y bus-nr (0, 1) never detected anything; i2cdetect -l gave me correct ports; i2cdetect -y for the hdmi-port allways worked.

• 0

  Reputation Points

• 10 replies
• 6.3k views
• 2 followers

eibinger

December 16, 20223 yr

Sorry about off-topic, just got forum giveaway Banana Pi M2 Pro and got confused - manufacturer doesn't care to reveal power jack size and all my 5V power adapter plugins are too small or too large. Can some happy owner of this SBC share plugin dimensions?

• 1

  Reputation Points

• 1 reply
• 3.1k views

Arvo

December 15, 20223 yr

Hi everyone! I would like to install a wake up physical button on my Odroid n2+ gpio. I already know I have to edit the dtb files and specify something in ArmbianEnv but.. is there someone who could tell me what exactly I have to write? I'm using Armbian Jammy. Thanks!

• 0

  Reputation Points

• 1 reply
• 3.6k views

Terminator007

December 15, 20223 yr

Some time ago a I was desperate to have ZFS on an Odroid HC4 and after some trying found Armbian 21.05.8 Buster with Linux 5.10.57-meson64 on which I could compile ZFS module. Then I moved everything from the SD card to filesystems in a ZFS pool. It boots from SD card, though. And has been working fine for several months. Recently I bought another HC4 and took the current Armbian image for it: Armbian 22.08.8 Jammy with Linux 5.19.17-meson64 Everything works fine. Tried this image on the older HC4 and it doesn't see the second SSD. In the syslog I found this message: ata1: SATA link down (SStatus 0 SControl 300) …

• 0

  Reputation Points

• 18 replies
• 7.8k views

SteeMan

December 11, 20223 yr

Hi, i have armbian bullseye (headless) installed on my odroid-hc4. petitboot is disabled. The boot-partition lies on a sd-card while the root-partion is on a ssd. this configuration worked fine. After upgrading to armbian bullseye 22.11 the boot process stucks in initramfs cause the root file-system is not found anymore (ALERT! UUID=xxx does not exist. Dropping to a shell. The sd-card with the boot partition as well as the ssd with the root-partition can be mounted on another PC and seem to be flawless. the UUID shown in fstab and initramfs are identical. In initramfs ls /dev/sd* shows no devices while ls /dev/mm* shows the sdcard (mmcblk01...). I don't really …

• 0

  Reputation Points

• 7 replies
• 6.5k views

charly_53

December 9, 20223 yr

Title says it all.... Installed the latest on download for Le Potato today and so far I've found 2 issues... 1. On first boot, text was cropped left and bottom, had to press enter a couple of times to get the prompt to show at least so I could make the right selections. 2. After it booted, jumped right on to Chromium and was super laggy. Installed Firefox as an alternative but it's still kinda laggy while loading page, but it works great after page loads. I would like to have Chromium instead though. PRO: My rtl8821CU which was not working on any distro of Le Potato is finally working. I'm guessing it's a Kernel issue? This has kernel …

• 0

  Reputation Points

• 2 replies
• 3.6k views
• 1 follower

Igor

December 9, 20223 yr

Hello, Bluetooth stopped working in kernel 5.19.17-meson64 #22.11.1 root@nextcloudpi:~# hciconfig hci0: Type: Primary Bus: USB BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0 DOWN RX bytes:14 acl:0 sco:0 events:1 errors:0 TX bytes:3 acl:0 sco:0 commands:3 errors:2 root@nextcloudpi:~# hcitool dev Devices: root@nextcloudpi:~# dmesg | grep Bluetooth [ 10.005353] Bluetooth: Core ver 2.22 [ 10.010561] Bluetooth: HCI device and connection manager initialized [ 10.010582] Bluetooth: HCI socket layer initialized [ 10.010589] Bluetooth: L2CAP socket layer initialized [ 10.010621] Bluetooth: SCO socket…

• 0

  Reputation Points

• 0 replies
• 3.3k views

mirko

December 5, 20223 yr

USB gadget mode does currently not work OOTB on Armbian, but it can be enabled easily with a device tree change or overlay: /dts-v1/; /plugin/; / { compatible = "radxa,zero", "amlogic,g12a"; fragment@0 { target = <&usb>; __overlay__ { dr_mode = "otg"; }; }; }; I can open a PR for adding this as device tree overlay, or enabling OTG OOTB on Radxa Zero, like vendor did: https://github.com/radxa/kernel/commit/775a467 The latter would be simple. In case of an overlay, I'd need some hint about how to do it best: Adding it to the general meson64 overlays patch seems to be right: https://github.com/armbian/build/blob/master/p…

• 0

  Reputation Points

• 0 replies
• 3.6k views
• 1 follower

MichaIng

December 3, 20223 yr

Khadas VIM1S is an upcoming low-profile single board computer powered by an Amlogic S905Y4 quad-core Cortex-A35 processor that’s meant to provide an upgrade to the Amlogic S905X-powered Khadas VIM SBC introduced in 2016, and since then renamed to Khadas VIM1. Khadas has been teasing two new SBCs: the low-end Khadas VIM1S with S905Y4 SoC, and the most powerful Khadas Edge2 board equipped with a Rockchip RK3588S octa-core Cortex-A76/A55 processor. I have received both as you can clearly see from the photo above :), but I’m only allowed to write about information available publicly at this time, so today I’ll introduce the Khadas VIM1S which looks just like the VIM1 board. K…

• 0

  Reputation Points

• 2 replies
• 5.2k views

Igor

November 24, 20223 yr

I am trying to use the s905x on the Le Potato board to encode a 1080p video to stream via RTSP. Using software, the video is encoded anywhere in between the 5-7fps range. I want to use the hardware encoder that is available on the chip but I haven't been able to find any libraries that let me use the hardware on this specific board. I have tried installing the Mali-450 GPU drivers here (https://wiki.debian.org/MaliGraphics) but no luck.

• 0

  Reputation Points

• 1 reply
• 3.6k views

Da Xue

November 23, 20223 yr

I have recently acquired a BPI-M2 Pro with what is supposed to be USB WiFi (Realtek RTL8821CU). I am running Armbian 22.08.7 Bullseye. armbian-config does not recognize any WiFi. The output from lsusb -t also does not show the presence of USB WiFi as expected. root@bananapi-m2p:~# lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 5000M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/2p, 480M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M Do I have a defective device, or is the WiFi not actually a USB module? Is there something else I need to …

• 1

  Reputation Points

• 8 replies
• 5.1k views
• 1 follower

RayKnight

November 19, 20223 yr

Hello I've tried to install the newest Armbian image "Armbian_22.08.7_Bananapim5_jammy_edge_5.19.16_cinnamon_desktop.img.xz" Copied with Balena Etcher to SDcard. Attached a serial tty cable and started with card in SD-Slot. Unfortunately it stops while booting. Please can anybody help me ? Here is the serial log:

• 0

  Reputation Points

• 1 reply
• 4.6k views

Schaagi

November 13, 20223 yr

Just wanted to show off a bit of awesomeness! (Please excuse the dust)

• 0

  Reputation Points

• 1 reply
• 3k views

Da Xue

November 12, 20223 yr

Hi guys I'm new to this type of computer. I recently got the Le Potato and have tried flashing the armbian package for it with USBimager and Balena and still get no boot. I was able to use the Raspberry PI imager and got Raspbian installed. I'm not sure what exactly is going wrong. I am using a Sandisk Extreme V1 32g but was able to get raspbian on a Samsung Evo select 256g.

• 0

  Reputation Points

• 1 reply
• 2.7k views

TonyMac32

November 10, 20223 yr

Recently i've download and installed Armbian_22.08.7_Bananapim5_bullseye_edge_5.19.16_minimal.img into Banana Pi M5 board. Initial setup run smoothly. After run the reboot command the system stop halfway. Can I know how to solve this problem? I have copy the error message below. Thanks. U-Boot 2022.07-armbian (Oct 18 2022 - 07:30:35 +0000)bpi-m5 Model: Banana Pi BPI-M5 SoC: Amlogic Meson SM1 (S905X3) Revision 2b:c (10:2) DRAM: 3.8 GiB Core: 385 devices, 27 uclasses, devicetree: separate MMC: sd@ffe05000: 0, mmc@ffe07000: 1 Loading Environment from nowhere... OK In: serial Out: serial Err: serial Net: eth0: ethernet@ff3f000…

• 0

  Reputation Points

• 0 replies
• 3.4k views

hkkok

November 3, 20223 yr

Hi, in addition to this topic I would like to mention that the current Odroid N2 Firmware (Armbian 22.05.0-trunk.0004 Jammy with Linux 5.10.103-meson64 / U-Boot 2022.01-armbian (Mar 03 2022 - 19:25:51 +0000) odroid-n2/n2-plus) as well has difficulties with both the orange and the red coloured eMMC modules at this time. The orange coloured eMMC module is recognised but couldn't be activated ("unable to select a mode : -5"): Spoiler G12B:BL:6e7c85:7898ac;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0. bl2_stage1 bl2_stage_init 0x81 hw id: 0x0000 - pw…

• 1

  Reputation Points

• 22 replies
• 15.6k views
• 3 followers

einsteinx2

October 31, 20223 yr

Lepotato with Armbian Jammy armbianmonitor -u is here: https://pastebin.com/UVbLxVH0 Trying to use I2c to drive a SSD1306 type oled screen. All wires have been tested for continuity and are good. Screen is connected as follows: Screen SDA -> Pin 27 Screen SCL -> Pin 28 Screen VCC -> Pin 4 Screen GND -> Pin 6 ive enabled i2c-a and i2c-b via armbian-config i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -…

• 1

  Reputation Points

• 2 replies
• 4.4k views
• 1 follower

echo7394

October 31, 20223 yr

Been using the Lepotato with Armbian fine for a few weeks. Typically accessing via ssh over the network, suddenly after a reboot, it's not appearing on my network, solid red light, solid green light, and a blue heartbeat as well as the NIC light blinking as if network connection is functioning normally, but my network is not assigning an IP address and the potato isnt sending any packets. What might the problem be here? HDMI shows no output, using Armbian Jammy made for the tato.

• 0

  Reputation Points

• 2 replies
• 3.9k views
• 1 follower

echo7394

October 31, 20223 yr

Can OpenVFD be installed on the Armbian image for LePotato?

• 0

  Reputation Points

• 1 reply
• 3.2k views

Da Xue

October 26, 20223 yr

I have a Le Potato running raspbian bullseye. I'm having real trouble with remote access. I can ssh into the Le Potato but cannot get VNC to work. I have used VNC successfully on 5 Pi's over the years so do have experience. Any hints or links to help would be appreciated. I have looked at pi and potato forums to no avail. Thanks.

• 0

  Reputation Points

• 2 replies
• 3.8k views

Da Xue

October 26, 20223 yr

Hi, We're swapping the Khadas Fenix 4.9 and uboot v2015-01?? for the Armbian 5.10.y and corresponding mainline u-boot. In the "legacy" version we were able to use the u-boot script (then a dedicated boot.ini) for setting a gpio pin low like this gpio clear GPIOH_4 Unfortunately Armbian's mainline u-boot version does not recognize GPIOH_4 as a valid gpio pin name. Anyone able to help? Did the naming change? Gé

• 0

  Reputation Points

• 1 reply
• 3k views

gkkpch

October 18, 20223 yr

Hi everybody, I just got a hand on a generic tv box powered by 4 cores S905x. Performance from this tv box is not satisfied for me. So I am thinking about this VIM4. Can anyone please tell me how is single core and multi cores cpu performance on VIM4 vs S905x? How much faster is it?

• 0

  Reputation Points

• 0 replies
• 2.7k views
• 1 follower

incendio

October 12, 20223 yr

I tried the 5.10 images. Both Jammy and Buster. Both just give a black display, but the display does wake up(background LED is on) All LED's stay on. With sid 5.19 it boots normally. Blue LED flashes. Display works.

• 0

  Reputation Points

• 0 replies
• 2.1k views

NicoD

October 11, 20224 yr

I tried 3 las disk images in SD card, update and OMV is not available fo install. In all tutorials show that OMV is available there. But when on my N2, it's not available.

• 1

  Reputation Points

• 1 reply
• 4.2k views
• 1 follower

NicoD

October 7, 20224 yr

Long story short: I used for about one year an odroid HC4 as NFS server and worked fine. Now I would add a player service for it. It mounts an HDMI port, so I tried to plug in the cable and it worked. I were able to see the video output but with no sound. I found there is no detected hdmi card: # aplay -l **** List of PLAYBACK Hardware Devices **** card 0: ODROIDHC4 [ODROID-HC4], device 0: fe.dai-link-0 (*) [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: ODROIDHC4 [ODROID-HC4], device 1: fe.dai-link-1 (*) [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: ODROIDHC4 [ODROID-HC4], device 2: fe.dai-link-2 (*) [] Subdevices: 1/1 Subdevice #0: sub…

• 0

  Reputation Points

• 0 replies
• 4k views
• 1 follower

foscove

September 28, 20224 yr

Hi there, yesterday I tried to use nand install skript tool to move the content from my sd card on odroid n2 to emmc card for booting and using emmc card only. The process itself worked and the content of the sd cards was moved, but after unplugging sd card and plugging emmc card the boot process is not starting and nothing is shown on the hdmi monitor. I compared the /boot filesystems and both are identically. I checked the "armbianEnv.txt" file and it is ok for the new uuid of the emmc card. Everything seems to be identically but why is it not booting. Does someone have a hint what to check additionally what is maybe missing at beginning of the boot process.…

• 0

  Reputation Points

• 25 replies
• 16.8k views
• 3 followers

Franky66

September 28, 20224 yr

Hi I was using: Title: Armbian 21.08.5 Odroidhc4 Debian buster legacy Then something bad pushed me to run apt update/upgrade No ZFS anymore. Installed 22.08.2, but, when tried to install kernel headers using armbian-config, result: "grep: invalid max count" message. What is the current correct way to install Armbian with ZFS? Thanks ChrisO

• 0

  Reputation Points

• 5 replies
• 4.6k views
• 1 follower

ChrisO

September 28, 20224 yr

Hello, After a firmware update today I got a problem with Wireguard on my Odroid-hc4. I got that when checking ufw status, sudo ufw status verbose ERROR: problem running iptables: modprobe: FATAL: Module ip_tables not found in directory /lib/modules/5.10.123-meson64 iptables v1.8.7 (legacy): can't initialize iptables table `filter': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How to fix that? Laurent

• 0

  Reputation Points

• 11 replies
• 11.6k views

Guest

September 25, 20224 yr

Hi, has anyone got the Odroid VU7-C display to work on a Odroid N2+ running headless Armbian Jammy? Running the hardkernel stock 22.04, which is still on linux kernel 4.9, it works fine. I've already tried to change a few boot params in /boot/boot.cmd, inspired by https://wiki.odroid.com/accessory/display/vu_series/vu7/vu7#tab__odroid-n2 like setenv display_autodetect "true" or setenv disable_vu7 "false" setenv hdmimode “800x480p60hz” setenv voutmode "dvi" Am I correct to run mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr as root after each change in boot.cmd? I noticed in the hardk…

• 0

  Reputation Points

• 0 replies
• 2.5k views
• 1 follower

oddulf

September 22, 20224 yr

I've tried multiple time on different cards. Both images, give me the same result. At first I'm able to edit files then after a restart or two I'm no longer able to edit files. Can't even touch a new file as root. I have tried at least 10 times today with both images. Every time I end up in the same situation unable to edit the sd card.

• 0

  Reputation Points

• 4 replies
• 3.3k views

smarttowers

September 18, 20224 yr

I've been trying to enable SPI on the board but have had no luck in this. I noticed that in the armbian-config there is no spi option. I have edited the armbianEnv.txt file to include orerlays = spi-spidev param_spidev_spi_bus = 0 I've tried changing the bus to 1 None of these actions have helped. Any advice would be greatly appreciated.

• 0

  Reputation Points

• 2 replies
• 4.5k views

smarttowers

September 18, 20224 yr

Is there any way to enable Wake on Lan? As far as I know the Odroid-HC4 Supports WoL but I can't get it to work

• 1

  Reputation Points

• 4 replies
• 6k views

Sakuraa

September 13, 20224 yr

I don't understand why I can't update to 5.19. I just updated to various user-space Debian 11.5 packages, but I can't see any newer kernels. root@odo:/boot# apt policy linux-image-edge-meson64 linux-image-edge-meson64: Installed: 22.05.1 Candidate: 22.05.1 Version table: *** 22.05.1 500 500 https://mirrors.xtom.de/armbian bullseye/main arm64 Packages 100 /var/lib/dpkg/status 22.02.1 500 500 https://mirrors.xtom.de/armbian bullseye/main arm64 Packages 22.02.0-trunk.0046 500 500 https://mirrors.xtom.de/armbian bullseye/main arm64 Packages 22.02.0-trunk.0045 500 500 https://mirrors.xtom.de/armbian bullse…

• 0

  Reputation Points

• 3 replies
• 4.6k views

Werner

September 12, 20224 yr

It took me a day and a week to get it somewhat working but I have Retropie installed and would like to have Emulation Station auto start after login. The setting from within the Retropie Setup script does nothing. Typing "emulationstation" after login does indeed run the program but Id like a way to have it autostart once the Potato is powered on (like a Raspberry Pi 3).

• 0

  Reputation Points

• 1 reply
• 5k views

Da Xue

September 7, 20224 yr

I have been reading about webcams, etc. and Linux and am working with my LePotato running Ubuntu 22.04. I added the Arduino CSI-USB converter so I can plug in an RPiHQ cam into the USB port. I see the following in the log messages: pi@lepotato:~$ dmesg | grep Camera [ 4.431905] usb 1-1.2: Product: Arducam IMX477 HQ Camera [ 8.798501] uvcvideo: Found UVC 1.00 device Arducam IMX477 HQ Camera (0c45:636d) [ 8.806595] input: Arducam IMX477 HQ Camera: Arduc as /devices/platform/soc/d0078080.usb/c9000000.usb/xhci-hcd.2.auto/usb1/1-1/1-1.2/1-1.2:1.0/input/input3 But I have no idea how to test further. I've tried cheese: cheese …

• 0

  Reputation Points

• 1 reply
• 5.7k views
• 1 follower

Da Xue

September 7, 20224 yr

Hello, I'm pretty new to Armbian and also to Odroid devices. I'm trying to use Armbian as main operating system (instead of official Ubuntu image). If I burn SD with official Ubuntu image, it work well, if I try to burn almost any of Armbian images for Odroid N2/N2+, I can't get them to work. I've tried theese images: Armbian 22.08.1 Bullseye Armbian 22.05.4 Bullseye Armbian 21.08.1 Bullseye Armbian 22.05.4 Jammy Armbian 22.05.4 Jammy Armbian 21.05.2 Hirsute Edge As per Ubuntu, I've downloaded them, burnt with BalenaEtcher on SD, put the SD in switched-off odroid, attach hdmi, lan, keyboard an…

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

Stefano Roncalli

September 2, 20224 yr

I have an Odroid-N2+ and I would like very much to Armbian on it. However, when I run lspcu I see that mitigations for hardware side channel attacks are missing: $ lscpu Architecture: aarch64 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 6 On-line CPU(s) list: 0-5 Vendor ID: ARM Model name: Cortex-A53 Model: 4 Thread(s) per core: 1 Core(s) per socket: 2 Socket(s): 1 Stepping: r0p4 CPU max MHz: 2016.0000 CPU min MHz: 1000.0000 BogoMIPS: 48.00 Flags: fp asimd evtstrm aes …

• 0

  Reputation Points

• 1 reply
• 3.1k views

Igor

August 19, 20224 yr

Armbian_22.05.4_Odroidn2_jammy_current_5.10.123_xfce_desktop.img ... comes up with the Armbian logo and circling dots... But the dots go on for an hour and a half. Here's what /var/log/bootstrap.log looks like.

• 1

  Reputation Points

• 22 replies
• 8.2k views
• 1 follower

usual user

August 9, 20224 yr

Hi, Odroid N2+ Armbian 22.05 Jammy Kernel 5.10.y, Size: 360Mb, Updated: Jul 1, 2022 + XFCE installed by means of armbian-config htop shows Systemd: degraded (1/372 failed) root@n2p-dev:~# systemctl --failed UNIT LOAD ACTIVE SUB DESCRIPTION ● fwupd-refresh.service loaded failed failed Refresh fwupd metadata and update motd LOAD = Reflects whether the unit definition was properly loaded. ACTIVE = The high-level unit activation state, i.e. generalization of SUB. SUB = The low-level unit activation state, values depend on unit type. 1 loaded units listed. root@n2p-d…

• 0

  Reputation Points

• 0 replies
• 3.9k views

vinser

August 4, 20224 yr

I get a pink tinted screen, on the N2+. Tried different DMs (Gnome, XFCE, KDE), and a second N2+ I have. Changing my monitor's icc profile to a generic sRGB in GNOME and KDE does nothing. Using the same monitor and cable on my regular desktop I not have this problem.

• 0

  Reputation Points

• 2 replies
• 3.1k views

HelenFr

July 17, 20224 yr

Hi guys! Image from that link http://imola.armbian.com/dl/khadas-vim3l/archive/Armbian_22.05.1_Khadas-vim3l_jammy_edge_5.17.5_xfce_desktop.img.xz is about 352 Mb. When Im unzip it - 7zip give me error. http://imola.armbian.com/dl/khadas-vim3l/archive/Armbian_22.05.1_Khadas-vim3l_focal_current_5.10.110_xfce_desktop.img.xz - same problem. By the way I have some problem with building image by myself, some time it gives me complete with success, but image is broken too. I think so because first boot take loooooong time with no set root pwd, only rounding circle and second boot don't give me to set root pass and other credentials. So if it possible, could you test that …

• 1

  Reputation Points

• 4 replies
• 4.3k views
• 1 follower

rpardini

July 6, 20224 yr

Hi I had to upgrade my Odroid N2 from Armbian Buster to Armbian Bullseye to run newer versions of Nextcloudpi (24.x). So I did the upgrade by writing the Armbian 22.05 version to the eMMC and started Armbian. Works fine. Then I installed a fresh nextcloudpi (23.0.2) which is the same version I used on Armbian Buster. Works fine. I added the external disks (ncdata und ncbackup). After a restore of my nextcloudpi backup everything was well. But the next reboot did nothing, i.e. no output on the HDMI Interface, nothing. So, I did a power-off and looked at the eMMC via a Micro-SD adapter I have. Of course, no logs, nothing. …

• 0

  Reputation Points

• 1 reply
• 3k views

NOBL

July 1, 20224 yr

Hi! You can find the armbianmonitor output attached to this thread. The issue is: when I use HDMI audio output with wine applications the entire system freezes very soon, usually after some seconds from the launch of the application. Some fraction of the latest played sound keeps looping very fast and both mouse and keyboard are unresponsive. All I can do is to unplug the power. This happens both on Odroid N2 and Odroid N2+. Everything works fine if I use some bluetooth headphones. And everything works fine if I use HDMI audio output with linux native applications. The problem is in the combination of Wine applications and HDMI audio output. Armbian Monitor Out…

• 0

  Reputation Points

• 0 replies
• 2.4k views

Matz3D

June 8, 20224 yr

So, first of all, pretty much a newbie here. I'm trying to add protonvpn to my HC4. I was able to do it with Ubuntu Mate (from the HC4 webpage) on the same hardware, so I'm pretty sure it's possible on Armbian. To be fair, the ProtonVPN website says that raspbian is not supported (and I assume they meant to say ARM) but I have been able to get it to work on Mate, and the problem on Armbian seems to be the Public Key and nothing else. After installation, the app will start, but won't work, so some successful compiling for ARM seems to be happening. What I did: - Downloaded the deb file for Debian based stable release - Tried GDebi and Apt, but dpkg wo…

• 0

  Reputation Points

• 0 replies
• 3.9k views
• 1 follower

natsbar

June 1, 20224 yr

The image listed here with xfce is broken: https://www.armbian.com/odroid-n2/ Example download link to broken image: https://mirrors.dotsrc.org/armbian-dl/odroidn2/archive/Armbian_22.05.1_Odroidn2_focal_current_5.10.110_xfce_desktop.img.xz

• 1

  Reputation Points

• 1 reply
• 2.9k views

Igor

May 30, 20224 yr

I prefer Debian to Ubuntu. Is there a possibility the VIM3 version will run on the VIM4 (doubtful)? Is anyone currently working of Debian Bulleye support for the VIM4, or interested in befinning a port? Larry

• 0

  Reputation Points

• 1 reply
• 3.8k views

Werner

May 14, 20224 yr

I am attempting to install the v4l2loopback module for my device (Le Potato running Armbian 22.02.1 Bullseye) and am running to some issues. I installed linux-headers-5.10.102-meson64 since that matches the kernel image installed: marc@lepotato:/usr/src$ dpkg -l |grep linux-image ii linux-image-current-meson64 22.02.1 arm64 Linux kernel, armbian version 5.10.102-meson64 current marc@lepotato:/usr/src$ dpkg -l |grep linux-headers ii linux-headers-current-meson64 22.02.1 arm64 Linux kernel headers for 5.10.102-meson64 on arm64 current But when I try and install the v4l…

• 0

  Reputation Points

• 2 replies
• 4k views

mjasner

May 10, 20224 yr

Hello everybody. Today the Khadas VIM4 is being released. The VIM4 uses the Amlogic A311D2 SoC. This is a new SoC with 8-cores of which 4 x A53 @ 2Ghz + 4 x A73 @ 2.2Ghz. The board comes with 8GB LPDDR4X and an eMMC of 32GB. If you want to learn more about this new board, then watch my review video about it here. Greetings, NicoD

• 0

  Reputation Points

• 0 replies
• 3.7k views

NicoD

May 6, 20224 yr

First off, could someone please help. I did not seem to be able to create this topic without a tag and the only tag it would accept was "solved". Wondering if somebody could remove the "solved" tag and add in "odroidhc4"? I purchased a brand new odroid hc4 board with the intention of installing armbian and then subsequently OMV. My intention was/is to install Armbian on a MicroSD card. On the downloader page I read that in order to clean boot Armbian the incompatible Petit bootloader needs to be removed. I tried the bootloader bypass (preferred) method and that didn't seem to work for me. The board still seemed to go to the petitboot UI. …

• 0

  Reputation Points

• 2 replies
• 3.9k views

wolf7250

April 20, 20224 yr

Hi all. I've recently received the Odroid N2+. Since nobody else started a topic about it, I'll be the one. All works fine with Armbian since not much hardware changes have been made vs the N2. Except for the CPU frequency. With the Odroid Ubuntu you can set it to 2.4Ghz for the big cores A73 as overclock (2208 stock)., and 2016Mhz for the A53 cores (1908 stock). With Armbian the max clocks are 2Ghz for all cores. Using Armbian Focal 4.9 legacy. I tried setting the higher values in config.ini. Also tried with the "meson64_odroidn2_plus.dtb" file from the Odroid Ubuntu. Doesn't boot with that. (What do I know ) Other changes are the RTC b…

• 1

  Reputation Points

• 52 replies
• 45.6k views
• 2 followers

Ruediger

March 20, 20224 yr

Hi, I installed/compiled different browsers that are based on QT (QtWebKit, QtWebEngine). Unfortunately, special characters, often necessary for typing in non-English languages, do not work. E.g. a Spanish accented 'e appears as 00e9 This makes all these really fast browsers with low memory footprint useless for multilanguage writing (e.g. in webmailers). The characters work fine in the terminal and other browsers such as Midori, Firefox and Chromium. Thus, I think, something went wrong in the compilation of QT libraries. Any idea how to solve that?

• 0

  Reputation Points

• 0 replies
• 2.2k views

Robert-MX

March 14, 20224 yr

Hi, please ignore my username, it's quite old. System is an odroid n2+. After updating the system (apt dist-upgrade) and updating linux-image-current-meson64:arm64 21.08.1 to 21.08.6, my sd card could not be mount anymore. New firmware was: linux-image-current-meson64=21.08.6 / 5.10.81-meson64 System runs from emmc. The 256gb sd card is used for more internal storage. Kernel message: mmc0: error -84 whilst initialising SD card - repeated every few seconds. Downgrade back to linux-image-current-meson64=21.08.01 / 5.10.??-meson64 (did not remember minor version while changing kernel in armbian-config): works again…

• 1

  Reputation Points

• 7 replies
• 6.3k views
• 1 follower

bananapinas

February 16, 20224 yr

Sometimes when reboot device goes to emergency mode and you can not connect to it remotelly. I read on internet, may be here, that make this [Firmware Bug]. I downgrade Kernel to "Igor" recommended 5.7.15 and there the [Firmware Bug] missing. I tested new and newest Kernel via armbian-config but the [Firmware Bug] is present everywhere. Kernel 5.7.15 seems good without this bug but i have no sounds on Audio out or via HDMI. --- journalctl -xb [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader!

• 1

  Reputation Points

• 5 replies
• 5.3k views

MichaIng

January 27, 20224 yr

root@odroidn2:~# journalctl -x | grep haveged Mar 12 19:43:51 odroidn2 kernel: audit: type=1400 audit(1615574627.248:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/haveged" pid=1635 comm="apparmor_parser" Mar 12 19:43:47 odroidn2 audit[1635]: AVC apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/haveged" pid=1635 comm="apparmor_parser" -- Subject: A start job for unit haveged.service has finished successfully -- A start job for unit haveged.service has finished successfully. Mar 12 19:43:52 odroidn2 haveged[1836]: haveged: Couldn't initialize HAVEGE rng 9 Mar 12 19:43:52 odroidn2 haveged[1836]:…

• 0

  Reputation Points

• 6 replies
• 8.8k views
• 3 followers

MichaIng

January 24, 20224 yr

Hello, I want to have the GPU mali integration so I choose Armbian kernel 5.4 But there is no sound l. The command aplay -l not list any hardware. And no sound on HDMI An idea ? If I must choose another image can you tell me the good image ? And can I will keep the bifrost wayland integration ? Thanks a lot.

• 0

  Reputation Points

• 3 replies
• 4.4k views
• 1 follower

Igor

January 16, 20224 yr

Before I give it a try, has anyone already tried to write armbian to eMMC of the Le Potato ? If not, can you give me a hint where I shall read in order not to destroy the storage? * Thank you * it gets interesting from page 2 onwards

• 1

  Reputation Points

• 127 replies
• 82.5k views
• 5 followers

bosch_tracer

December 30, 20214 yr

Hello, Ihave an Odroid N2 that run with armbian. 1) I can't upgrade armbian-zsh_21.08.6_all.deb The output of apt upgrade is : (Lecture de la base de données... 133099 fichiers et répertoires déjà installés.) Préparation du dépaquetage de .../armbian-zsh_21.08.6_all.deb ... Dépaquetage de armbian-zsh (21.08.6) sur (21.08.5) ... dpkg: erreur de traitement de l'archive /var/cache/apt/archives/armbian-zsh_21.08.6_all.deb (--unpack) : impossible d'ouvrir « /etc/oh-my-zsh/plugins/osx/README.md.dpkg-new »: Aucun fichier ou dossier de ce type Des erreurs ont été rencontrées pendant l'exécution : /var/cache/apt/archives/arm…

• 0

  Reputation Points

• 1 reply
• 3.5k views
• 1 follower

abeille

November 26, 20214 yr

From time to time, I notice that the HC4 looses its IP address. journalctl then tells me: dhcp4 (eth0): selecting lease failed: -131 But I don't know the reason for it. Sometimes it happens after a reboot. Pulling the ethernet cable off and plugging it in again seems to help and after a few tries, the HC4 is reachable again. I'd be happy to give more information, but I don't know yet how to debug it. I noticed that /var/log (zram) sometimes gets full but I don't know if this is related…

• 1

  Reputation Points

• 5 replies
• 5.4k views

Igor

November 25, 20214 yr