Rockchip

Trying to set Wireguard (www.wireguard.io). I can compile and load the module (which is an issue on most distributions as they lack the necessary kernel headers), but bringing up the interface fails: root@tinkerboard:/etc/wireguard# wg-quick up mullvad [#] ip link add mullvad type wireguard [#] wg setconf mullvad /dev/fd/63 [#] ip address add 10.99.0.23 dev mullvad [#] ip link set mtu 1420 dev mullvad [#] ip link set mullvad up [#] wg set mullvad fwmark 51820 [#] ip -6 route add ::/0 dev mullvad table 51820 [#] ip -6 rule add not fwmark 51820 table 51820 RTNETLINK answers: Address family not supported by protocol […

• 1

  Reputation Points

• 19 replies
• 17.9k views
• 3 followers

lampra

December 17, 20178 yr

I have an Orange Pi 5 board, installed with the 25.8 Debian Bookworm + Cinnamon desktop system. I have switched (using armbian-config) to the edge kernel in order to test the HDMI audio support in the new Linux kernel, but I'm not getting any audio out. The ALSA HDMI card seems to be present (see below), but there's no sound using speaker-test or aplay. I have enabled the hdmirx overlay through armbian-config also, but the result is the same. Is there anything extra that should be configured in order to get audio output ? Output from armbianmonitor - https://paste.armbian.com/gegorimako

• 0

  Reputation Points

• 19 replies
• 10.2k views
• 2 followers

mitu

October 6, 20251 yr

hi there, I'm a complete Linux noob so please forgive my ignorance. But I do have 25+ years experience in IT so am relatively conversant with basic principles - so please be patient I did try to search for any previous threads but couldn't find any. I'm trying to setup a RADXA Rock 5 ITX with OpenMediaVault for my NAS. I have a 2TB NVMe m.2 SSD that I'll use for the OS. For the NAS storage I'm using 4x Western Digital 16TB SATA III drives. I downloaded the Armbian 25.2.2 bootable image from https://www.armbian.com/radxa-rock-5-itx/ and used Balena Etcher (the legit version from Balena-io) to make my bootable microSD card. …

• 1

  Reputation Points

• 18 replies
• 10.5k views
• 1 follower

nyecov

January 15Jan 15

Hi, all. After I upgraded the system and rebooted, the secondary ethernet port(i.e. the LAN port) is gone. The system info: https://paste.armbian.com/ekotoqigos nanopi-r4s:~:% ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 68:27:19:ad:02:09 brd ff:ff:ff:ff:ff:ff in…

• 1

  Reputation Points

• 18 replies
• 8.1k views

ArmUser

March 23Mar 23

Hi Anyone else having problems with NVMe disks on the Orange Pi 5 Plus 16gb? I have a WD Black SN750 and use the original power supply, I have tried with Armbian and Ubuntu Rockchip and with both I have random failures at startup not recognizing the drive. When fail I do this tests: 08:13:33 cristian@orangepi5-plus ~ → lspci 0000:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd Device 3588 (rev 01) 0000:01:00.0 Non-Volatile memory controller: Sandisk Corp Device 501e 0002:20:00.0 PCI bridge: Rockchip Electronics Co., Ltd Device 3588 (rev 01) 0002:21:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8822CE 802.11ac PCIe Wireles…

• 0

  Reputation Points

• 18 replies
• 11.1k views
• 1 follower

Dome

January 8, 20251 yr

hello guys, i ve been lately working with nanopi-r5s which comes with a default openwrt os installed on EMMC. but i prefer working on the armbian images. that is why i installed debian 12 bookworm from https://www.armbian.com/nanopi-r5s/ anyway, r5s refuses to boot from sd card for no matter what. until i corrupted the emmc by mistake(i started flashing a default image to emmc but then took the power off before it is done). so now it boots from sd card. but now when m trying to install the image from sd card to emmc through armbian-install. it only shows option 5 and 6. as if it can not detect the emmc. so what m trying to figure o…

• 1

  Reputation Points

• 17 replies
• 15.1k views

sami

August 8, 20242 yr

I understand that panthor is not supported for wayland but in that case I would expect libmali to fill in... but I ended up with lvmpipe. The overlay along with another recent post led me to believe that panthor was the expected default and libmali was an artifact, but I'm now questioning that after finding a thread identifying use cases where libmali can be preferred and a comment suggesting panthor wouldn't be available until 6.13. As a result, I am now questioning if there is a reason that software acceleration is the default and the user is expected to determine which path they want to go? I know support for the hardware has been slow going so I …

• 1

  Reputation Points

• 17 replies
• 11.4k views
• 1 follower

usual user

December 10, 2025Dec 10

I'm really struggling to get chromium to work correctly with hardware acceleration. 1) I have custom kernel image from master branch last week. Which maybe could cause some issues? 2) I added the two repos (panfork and mesa) sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia 3) I've ran all the updates 4) I installed ubuntu desktop to enable Wayland which is working nicely 5) I've added the HDMI audio output 6) My default chromium configuration does already have the egl enabled. When I start Chromium, I get the following errors 39610:39643:0125/091804.694008:ERR…

• 1

  Reputation Points

• 17 replies
• 31.2k views
• 1 follower

SuperMaximus

March 18, 20233 yr

Hello all, First of all, thanks for the Armbian project, love it so far, but had a slight problem with a kernel upgrade. To be honest, I forgot how I installed Armbian since it was a while ago, but I've been using this for a year or so. I saw that unattended-upgrades installed a new kernel and I should reboot for this change. I was a bit apprehensive, but went ahead and rebooted. The NanoPI R4S didn't come back up. I attached a serial console to debug. The console showed that the initramfs was read successfully from the SD card, but then tried to mount to root filesystem by UUID and failed (it kept saying it tried to run /boot/local-block and event…

• 1

  Reputation Points

• 17 replies
• 11.7k views
• 1 follower

Michiel Holtkamp

August 8, 20224 yr

I'm looking to try an OPi5 for GPGPU. After seeing trunk recently added the patches needed to use the "gofaster" option for panfork, and having seen reports of glmark2 scores of 4000 and 5000 while never coming close to that myself, I decided to pull together the various bits of info out there and just try all of the options. A number of things done below are often described vaguely -- hopefully it's helpful here to lay out a concrete set of steps to follow and what to expect. There are two options for accelerated video: panfork and ARM's closed source "blob" driver. With either option, it sounds like you should switch from X11 to Wayland. If you are looking a…

• 1

  Reputation Points

• 17 replies
• 38.5k views
• 1 follower

balbes150

March 21, 20233 yr

Hello everyone, This is my 1st post on the forum. My intention with this post is not to report a specific issue that I am running into, but more because I would like to collect info and suggestions from people with more experience than myself. I've recently received an Orange Pi 5 Plus and have spent a bit of time exploring operating systems suitable for this system and have settled on the Armbian solution. I'm a HW designer by trade, and have done some SW work, but I do not consider myself proficient in SW at all. I find my way around things, but that's about as far as it goes.... For the my planned use of the OPi5+, I will need eMMC b…

• 1

  Reputation Points

• 17 replies
• 17.6k views
• 1 follower

Adams Hope

February 9, 20251 yr

We talk about test of different parts. It was orginal one topic but split. The other is https://forum.armbian.com/topic/12936-how-to-control-fan-on-rockpro64 @deathisunknown Which kernel are you using? 5.3.xxx? Until this week end, I was using Ayufan's kernel in order to have ats working (I have the nas box with a harddrive so I want to have some ventilation). I've switched to Armbian's current kernel (5.3.xxx, I don't remember the exact subversion) and noticed that the fan would not spin. Then I tried Armbian's dev kernel (5.4.0-rc1) and my fan works fine. I stumbled upon this thread in the mean time, but since as I remember the lates…

• 0

  Reputation Points

• 17 replies
• 7.7k views
• 1 follower

soerenderfor

February 5, 20206 yr

I followed a guide to install a system on my Rockpro64 but something happened where I had to reinstall it. However, when I reflashed the ubuntu server image and tried re-installing the system it got an error pertaining to one of my disk volumes. So I'm wondering how to re-format and remount and redo the LVM volume my SSD. Any help or tips would be greatly appreciated!

• 1

  Reputation Points

• 17 replies
• 8.9k views

kkdao

September 1, 20206 yr

Hello. I downloaded Armbian 22.05 Jammy XFCE for Desktop. When I boot up my Orange Pi 4 LTS everything looks good. The first problem was a Wi-Fi 5G password (system dont recognize my password), only 2.4G works. The second problem (and the main problem) was a display - when X start, my display turn off (I have HDMI-connection). What I am doing wrong?

• 0

  Reputation Points

• 17 replies
• 9.2k views
• 1 follower

SET

August 27, 20224 yr

Hi all, I'm running Armbian 4.19 (both stable kernel 5.77 and nightly) on an TinkerBoard S. I'm trying to connect a 3.2inch resistive Touch Display to SPI2. The display works with ili9341 module on SPI2 CS0. I have the touch screen of it on the SPI2@1 (CS1) but no way of getting a module or overlay dts for the ADS7846 TouchScreen. I've seen, there is a generice resisitive-adc-touch module, but I can't get it running. Using the ADS7846 on armbian with AllWinner and several other boards for many years. Works great so far. Any hints, how to get it running in such a way, that it will be there with downstream updates (meaning without h…

• 0

  Reputation Points

• 17 replies
• 9.8k views
• 1 follower

TonyMac32

June 7, 20197 yr

Hello all, I downloaded the Armbian Buster OS desktop version. I need to run it with a vertical display - portrait mode. The OS starts correctly and I see the desktop in landscape mode but when I try to rotate left the display, it does not rotate and return to landscape mode. The display is a large NBT monitor 1920x1080 that I need to rotate to 1080x1920. Any idea? Regards

• 0

  Reputation Points

• 17 replies
• 8.3k views

Igor

November 5, 20196 yr

FYI latest image for rock 5B+ in downloads section is broken (Armbian_25.5.1_Rock-5b-plus_noble_vendor_6.1.115_gnome_desktop) Wont boot at all, previous 25.2.2 images works fine.

• 0

  Reputation Points

• 16 replies
• 10.3k views
• 1 follower

Igor

November 17, 2025Nov 17

Hi, I'm trying to get h264 encoding working but VAINFO keeps searching for rockchip_drv_video.so which is nowhere to be found on my system. Is there a way to get h264 encoding working with armbian OR do I have to use radxa oses (or the ubuntu version provided by Joshua Riek) ? Thanks.

• 0

  Reputation Points

• 16 replies
• 15.1k views

eselarm

March 19, 20251 yr

System Information: https://paste.armbian.com/mozehisomu When i am trying to setup many vlan interfacces i have whis dmesg message: rk_gmac-dwmac fe1c0000.ethernet eth0: MAC_VLAN_Tag_Filter full (size: 4) interface info: ethtool -i eth0 driver: st_gmac version: Jan_2016 firmware-version: expansion-rom-version: bus-info: supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: yes supports-priv-flags: no I need about 20-30 vlan interfaces

• 0

  Reputation Points

• 16 replies
• 8.3k views
• 4 followers

DeVILRuNNeR

January 22, 20251 yr

I'm using Armbian_5.32.170920_Tinkerboard_Ubuntu_xenial_dev_4.13.0_desktop.img (yes I know it's a nightly) and it works great. However if I run "apt-get upgrade" something gets "upgraded" and the display no longer works. I've tested this on multiple tinkerboards with the same results. The tinkerboard is running, I can ssh into it. Just no display. dmesg output: Spoiler armbian@tinkerboard:~$ dmesg [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 4.14.0-rc1-rockchip (root@armbian) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4)) #2 SMP PREEMPT Wed Sep 20 11:37:48 CEST 2017 [ 0.000000] CPU…

• 0

  Reputation Points

• 16 replies
• 5.2k views
• 1 follower

TonyMac32

September 21, 20179 yr

Hi guys, First post here, I successfully managed to flash and boot Armbian 25.8.2 (Bookworm Minimal) from an SD card. Everything was working great, HDMI output and network included. I then ran “sudo armbian-install” and selected Option 4 to move the system to my NVMe SSD and make it boot from there. The process itself completed without errors. However, after shutting down and removing the SD card and powering on again the system doesn’t boot. I have the red LED turned on however the green LED that was previously flickering doesn’t turn on. There’s also no HDMI output and the board doesn’t connect to the network. I tried ins…

• 0

  Reputation Points

• 16 replies
• 6.6k views
• 1 follower

eselarm

December 12, 2025Dec 12

Hello, I have an orange Pi5, i had installed armbian a few years ago and everything was working fine. Roughly one year ago i turn it off and kept off until now. A few days ago I tried to turn it on again and i've inserted a new sd card containing armbian but it doesn't boot. I've re created the sd card a few times and also used another sd card because i was thinking something was wrong with the card. The board turn on but i got only the red led, and is stable. Searching on internet i found that maybe the Orange Pi is bricked, so i tried to use the MaskRom and Recovery button, but nothing happen. Also i'm not able to see the board inside the RKDevTool, neithe…

• 1

  Reputation Points

• 16 replies
• 2.9k views

Simo

September 14Sep 14

Dear all, I have recently acquired an ODROID M1 board and flashed Armbian 24.5.3 on it to replace my old XU4 running Armbian 24.5.1. I've managed to port everything from the old XU4 to the new M1 except for two WiFi dongles. They worked just fine on the XU4 but the M1 just doesn't want to recognize them, I can see them when I run `lsusb` Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 0bda:0811 Realtek Semiconductor Corp. Realtek 8812AU/8821AU 802.11ac WLAN Adapter [USB Wireless Dual-Band Adapte…

• 0

  Reputation Points

• 16 replies
• 8.4k views
• 1 follower

Igor

April 7, 20251 yr

On several RockPro64 boards I experience infrequent freezes, mostly directly on boot, but also after some longer (hours, days) uptime. I use the official power adapter and no additional hardware except a PCIe adapter for an SSD, which works flawlessly when operational. When looking at the kern.log, there are quite a few errors and warnings, but comparing to a successful boot these are all also present. So I don't think they cause the freeze directly. Currently, I recorded the freeze on the latest Armbian Bionic as release just recently. FWIW, I think the same issue also occurs on the previous Debian Stretch image (had various freezes, but have not …

• 1

  Reputation Points

• 16 replies
• 10.7k views
• 1 follower

Myy

April 1, 20206 yr

I downloaded the tinker nightly image and burned it to an sd card, putting it into the tinker it does nothing, the red light comes on but does nothing, the sd card is decent, and works fine if i write an image to it for a pi, power supply is fine as well, anyone got any suggestions as to my next steps getting this booted. Thanks

• 1

  Reputation Points

• 16 replies
• 30.3k views
• 1 follower

TonyMac32

July 30, 20188 yr

Hello, I'm observing a strange behavior. If I connect the Tinkerboard to HDMI, it won't start. Only the red led LED lights up. Yellow and green did not light up. The Tinkerboard ist connected to a NorthPada 5V 3A Micro USB Charger power supply. I measured the supply voltage with 5.3V and checked with an oscilloscope if there are voltage dips. But the voltage was stable. I did a cross test. I unplugged the HDMI cable and started the Tinkerboard. The Tinkerboard starts and the yellow and green LEDs lights up. I measured the supply voltage with 5.3V and checked with an oscilloscope if there a voltage dips. The voltage was stable and dropped to roughly 5.1V for a short ti…

• 1

  Reputation Points

• 16 replies
• 11.6k views

TonyMac32

December 6, 20187 yr

Has anyone seen this? The claims there is a Vulkan driver now: https://github.com/Bleach665/Mali610Vulkan Can't confirm.

• 1

  Reputation Points

• 16 replies
• 25.5k views
• 1 follower

Avatar Ng

June 1, 20251 yr

Hy, I have tried to use my tinkerboard like an hotspot. configuration done with armbian-config. when i used the armbian jessie ( ARMBIAN 5.73 stable Debian GNU/Linux 8 (jessie) 4.19.20-rockchip) : everything works IF i don't do an apt-upgrade. If i do an apt-upgrade or using the last img of armbian strectch, i cannot connect any devices to my Tinkerboard : here what i have when i used ssh to see what's wrong : Spoiler root@tinkerboard:~# Message from syslogd@localhost at Feb 20 01:22:35 ... kernel:[ 42.906202] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM Message from syslogd@localhost at Feb 20 01:22:35 ...…

• 1

  Reputation Points

• 16 replies
• 7.1k views
• 1 follower

dragonlost

March 21, 20197 yr

Anyone who typically updates on nightly kernels I would recommend freezing and not updating until we clear up some issues gifted us by some large amount of upstream changes that broke well, pretty much everything. I will update this thread as things get brought back to life. June 7th 2018: I've made a branch (rockchip-default) to work out the kinks. So far I have the board booting and Mali working again (with an initial error on load) , however there is no HDMI terminal, so initial boots would require a uart or SSH hdmi terminal is back thank you to Ntemis on github, I'd missed part of the conversation (I only have cell phone while at w…

• 1

  Reputation Points

• 16 replies
• 16.1k views
• 2 followers

TonyMac32

July 20, 20197 yr

I try to get working a tinkerboard on a battery. I can do that with S.USV or S.USV Mobile but i don't know the difference between them. I have a xl4015 (5Amp buck convecter) but I don't really understand how it's work (i have a lm2596 too). I have a 20AWG micro-usb too but i can power it too from gpio. So i search a quick way to get it work on a battery. I work and search on this since 5 week and i really need to get it work. Thx

• 1

  Reputation Points

• 15 replies
• 10.6k views
• 2 followers

Sangram

April 12, 20188 yr

This image works OK, and we now have both a 6.7 kernel AND graphics. Minor issues: EzCast stupid windows Wifi adapter does not plug and play. The vertical USB port does not sense plugging in a device (Wifi) Good work, Gullik

• 1

  Reputation Points

• 15 replies
• 6.8k views

Gullik

January 9, 20242 yr

My setup is still running, yay! I even updated to Trixie and all worked out fine. But I'm stuck on edge kernel 6.12.x, I saw that rolling had 6.16.x. So how do I install/convert to the rolling 6.16.x edge kernel ?

• 0

  Reputation Points

• 15 replies
• 8.7k views

Werner

October 3, 20251 yr

Hi. I have RockPi E v1.21 and I found, that I'm not able to boot image with new kernel 6.12 (tried minimal images 25.2.1 and 24.11.1, USBImager and Balena Etcher, 3 SD cards, different power supplies). With image 24.8.3 it boots normally. Also I found, that after upgrading 24.8.3 to kernel 6.12 the RockPi boots, but Ethernet doesn't work (even LEDs are dead). Another thing which I notice is, that I didn't find any option to disable kernel upgrades, but what I googled, it should be present in armbian-config->system->kernel->Y203. But this Y203 option is missing. Here is successful boot log of 24.8.3: https://paste.armbian.com/ixuvimofis.sql …

• 0

  Reputation Points

• 15 replies
• 7.8k views
• 2 followers

Benik3

May 26, 20251 yr

Hmm... I have similar problem for Asus tinkerboard hangs thread's thing. First, I've reinstall OS few days ago, because OS partition is crashed by system hangs. I've test next build but it can't be reboot (I don't know why). cause I've install legacy build. It looks pretty works well, so I've install 'transmission-daemon' to build my own seedbox. I've plugged 500GB 2.5in External HDD and 128GB Flash Drive, and use 3A Micro-USB adapter. then... ta-da! system hangs! generally It works good 1~2 days after boot. but randomly hangs. I think it's temp things cause install Fan on 3.3V GPIO, but same. It hangs. B…

• 1

  Reputation Points

• 15 replies
• 12.3k views
• 1 follower

mpmc

October 28, 20178 yr

Hopefully this is not a stupid question but I came across Joshua-Riek/ubuntu-rockchip: Ubuntu for Rockchip RK35XX Devices (github.com) when searching for my video playback issues. Does anyone know how this compares with the current armbian release with vendor kernel? Are all the fixes from that release integrated in armbian or does it go the other way?

• 1

  Reputation Points

• 15 replies
• 19.7k views
• 1 follower

going

November 1, 20241 yr

Hi, I'm pretty new to this forum may be I will ask some already answered questions, but here they are: I just had a new orangepi 5 plus card and I failed to use the "buses": - I2s: didn't find anywhere how to activate it (i'm trying a dac as a soundcard). Didn't find the hifiberry-dac overlay neither (ok maybe this one is just for raspberry). - spi: I plugged a simple mcp3008 to the spi pins but can't read anything on it (i have the /dev/spidev0.0/1 and /dev/spiddev4.0/1 devices). I think I respected the rights pins. - i2c: when I activate the overlays in armbianEnv.txt, I can see a lot of messages every seconds with dmesg about rk-hdmi. Ma…

• 1

  Reputation Points

• 15 replies
• 16k views

Igor

December 10, 20232 yr

Hi, Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110 works well with my OPI5. I can ssh to and play with it from my Debian desktop. I don't have HDMI monitor so I want to try serial port. i'm using USB-TTL cable to connect OPI5 to my Debian box. Then in Debian bash I use this command to connect to the port screen /dev/ttyUSB0 Then power on the OPI5. The output is garbled: If i change it to cs7 (screen /dev/ttyUSB0 cs7), the output is still something I cannot understand: The stty command and output: $ sudo stty --file=/dev/ttyUSB0 --all speed 9600 baud; rows 0; columns 0; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; e…

• 1

  Reputation Points

• 15 replies
• 11.9k views
• 1 follower

royk

June 5, 20233 yr

I've got jammy running but I have a dsi display for the board and I'd like that to work (well the tp port too) with jammy. Looking at armbian config I see no setting for it. I know the display works fine as if I load an aryufan android image it works as it is set to use DSI by default. Does this kernel know about the DSI port? Do I have to build a custom kernel? If not then what boot env line will get it going?

• 0

  Reputation Points

• 14 replies
• 8.6k views
• 1 follower

dkebler

January 7, 20233 yr

I originally posted this on reddit after seeing a lot of posts trying to use a SATA M.2 SSD and saying it wouldn't boot with replies telling them to go buy a NVME M.2 SSD which isn't necessary when the board does support SATA M.2 with flashing the correct bootloader. This guide has 3 different sections, 1 being booting with Orange pi OS and 2 being with Armbian OS Orange Pi OS Instructions Download Orange Pi OS Ubuntu or Debian from their website http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/service-and-support/Orange-pi-5.html unzip the 7z file to get the .img file and flash it to your sd card with your preferred flasher i.e balenaetc…

• 1

  Reputation Points

• 14 replies
• 51.9k views
• 1 follower

dionisisl_

February 21Feb 21

Orange PI 5 doesn't boot after firmware update using ARMBIAN beta tool. There isn't so much documentation, as this board is new. How to recover the firmware?

• 0

  Reputation Points

• 14 replies
• 22.6k views
• 1 follower

royk

April 9, 20233 yr

Hello, i will move my project from RPI2 to tinkerboard. I have 2 Serial Converter, USB to RS422 and USB to RS485, both working on the PI. On the Tinkerboard with "ARMBIAN 5.33 stable Ubuntu 16.04.3 LTS 4.13.3-rockchip" runs only the RS422, the RS485 (Vendor 1a86) is not available as /dev/ttyUSB. What can i do? Regards Marco Tinkerboard Log: Spoiler Oct 14 17:52:45 localhost kernel: [ 1.942542] usb 1-1.1: new full-speed USB device number 3 using dwc2 Oct 14 17:52:45 localhost kernel: [ 2.020053] usb 1-1.1: New USB device found, idVendor=1a86, idProduct=7523 Oct 14 17:52:45 localhost kerne…

• 0

  Reputation Points

• 14 replies
• 7.2k views

MB2

October 20, 20178 yr

Hello, After NanoPi R4S reboot, ethernet interface `enp1s0` disappeared. I tried soft reboot for several times but failed. If I shutdown the board and power plug out/in again, then `enp1s0` appears. I tested it several times and 100% same results. Any idea please? wg* is for vpn. please ignore them.

• 1

  Reputation Points

• 14 replies
• 8k views
• 1 follower

Igor

October 29, 20223 yr

Hello I cannot enable the Bluetooth on Tinkerboard device. Tried latest image, fresh install. I've opened the question on StackOverflow: https://superuser.com/questions/1698728/cannot-enable-bluetooth-on-tinkerboard-armbian It contains technical details. The latest what I've found so far is it could be related to Kernel compilation flags: # Extract from the /boot/config-5.10.60-rockchip CONFIG_SERIAL_DEV_BUS=y CONFIG_BT_HCIUART_3WIRE=y CONFIG_BT_HCIUART_SERDEV=y # CONFIG_BT_HCIUART_RTL - is not set # CONFIG_SERIAL_DEV_CTRL_TTYPORT - is not set I tried to download and compile the kernel and stuck. Basically I do…

• 0

  Reputation Points

• 14 replies
• 6.3k views

ning

November 7, 20223 yr

Hello, yesterday i got a powerloss , and my Asus tinkerboard got shutdown. i think i had some updates installed but not yet rebooted the Tinkerboard never restarted again. i first suspected a crashed Emmc disk but i did the following tests and got to the conclusion that Armbian for Tinkerboard is currently broken - restored a past complete image to either SD or Emmc : boots ok. - shutdown then unplug/replug power : OK - update with apt-get update + apt-get upgrade => reboot OK, but shutdown, and then never restart, bricked. shutdown down either with desktop or command line tested also with a second Tinkerbo…

• 1

  Reputation Points

• 14 replies
• 11k views

Igor

May 30, 20215 yr

Using 5.41 with Chromium 68.0... Using <input type="file"> on a web page... If you click a usb camera (probably usb stick as well) and the system mounts the usb (assuming it wasn't mounted already by other means)... after you close the dialog (whether you selected a file or clicked cancel)... chromium is frozen.

• 0

  Reputation Points

• 14 replies
• 4.2k views

freak

August 30, 20188 yr

I have an interesting discovery that smells suspiciously like a kernel bug. I find it easiest to see this bug by running btop which shows a historical per core cpu usage graph so it's easy to see when one stops being used. You can see the same thing in ordinary top but it's less easy to see than with btop. I have a Radxa Rock 5B with an RK3588 chip that I have been stress testing to make sure the hardware is OK before I start to use it in anger. As part of that I ran `openssl speed -multi 8` to spin up 8 threads using 100% cpu each. On all other machines that I've ever done that with it runs all X cores at 100% until it runs out of tests or is Ctrl-C'ed. Watch…

• 0

  Reputation Points

• 14 replies
• 1.9k views

spry_plover44

September 19Sep 19

Hi, I read everything I could possibly find on the DP-Alt mode for the RockPro64 and came to the conclusion that no Distro is offering that right now. However, the Pinebook Pro seems to have support via a Kernel Patch. Can the Pinebook Pro Kernel be installed on the RockPro64? Is there a repository for Armbian Kernels? Thanks very much.

• 1

  Reputation Points

• 14 replies
• 6.4k views
• 2 followers

going

July 21, 20242 yr

I try to understand the usage of Tinkerboard for Industrial Application usage, we have below questions. 1. Operating temperature is between 0-60 C [as many Industrial PLCs recommend 0-55 C only] 2. Long Term Supply of the Boards 3. Bulk Quantities buying [Get 30 to 50 boards in 2-4 weeks notice] The board and quality seems top notice, RPI interface is good for our use cases, anyone sees a risk in above points or would like to suggest something? We are looking a good sized community, Ubuntu OS, much stable and better performing board compared to Raspberry PI, all seems good with Tinkerboard. Please share your idea…

• 0

  Reputation Points

• 14 replies
• 8.1k views
• 1 follower

Gops

May 2, 20197 yr

Hello, I'm identifying myself has a newbie concerning linux. After some time I reboot my rock5c and it is not booting anymore. Here is what I've done initially: I bought a rock 5c and a penta sata hat. -I installed Armbian_24.5.1_Rock-5c_bookworm_edge_6.8.10_minimal. -I installed OMV (configure some samba shared folder) -I installed ZFS (for that I needed linux headers that I found online because there were not included) -I create a ZFS pull with two SSD. -I installed immich and setup a cloudflare tunel to use it. -I installed plex media server. That's pretty much all I have setup on my SBC. I've done apt upgrade multiple time &amp…

• 0

  Reputation Points

• 14 replies
• 14.2k views

eselarm

January 6, 20251 yr

Hello, I'm trying to install the zfs-dkms package with the latest build (Armbian_23.02.0-trunk.0127_Orangepi5_jammy_legacy_5.10.110_xfce_desktop.img.xz) and I get the following error: configure: error: *** This kernel does not include the required loadable module *** support! *** *** To build OpenZFS as a loadable Linux kernel module *** enable loadable module support by setting *** `CONFIG_MODULES=y` in the kernel configuration and run *** `make modules_prepare` in the Linux source tree. *** *** If you don't intend to enable loadable kernel module *** support, please com…

• 1

  Reputation Points

• 14 replies
• 10k views
• 2 followers

simonswine

January 21, 20242 yr

Is there a list of Armbian Kernels that include EMMC support? I've tried the vendor kernel build 6.1.99, the LTS 6.12.21, and Bleeding Edge 6.14.0 to find they all lack the mmcblk0 under /dev/ , and lack overlays for it under /boot/dtb/rockchip/overlays/. I have wiped SPI and SPNOR without success.

• 0

  Reputation Points

• 14 replies
• 8.4k views
• 1 follower

Robert Pace

April 18, 20251 yr

Hi! I seem to have the same problem described here: I have an Asus Tinkerboard, not the S version. Today I upgraded from the latest Asus TinkerOS image: 20190821-tinker-board-linaro-stretch-alip-v2.0.11.img to: Armbian_19.11.3.346_Tinkerboard_buster_current_5.3.15_minimal.img I notice that my maximum CPU frequency has dropped from 1.80GHz to 1.61GHz. cpufreq-info now reports: $ cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware freq…

• 1

  Reputation Points

• 13 replies
• 7.1k views
• 2 followers

ginggs

February 22, 20206 yr

Hi all, I just bought TinkerBoard S and I downloaded Armbian Stretch 4.19 (tried both with and without desktop ) and I tried to boot. But no luck I was waiting for few mins but nothing. I also tried Armbian Strech 4.4 but also nothing. Am I missing something here? Original TinkerOS work without any issue Thank you for any advice/help

• 1

  Reputation Points

• 13 replies
• 20.3k views
• 1 follower

dragonlost

December 13, 20196 yr

I hear something about a new version of the board Thinkerboard, "Tinkerboard S". I want to know what you know and think about it. https://www.asus.com/Single-Board-Computer/Tinker-Board-S/

• 1

  Reputation Points

• 13 replies
• 7.7k views

TonyMac32

February 16, 20188 yr

Hello, the latest armbian image (Bookworm_current_xfce) with kernel 6.6 has issues with the winstar tftp 5 inch hdmi display that I am using. Bootloader (u-boot) is showing but after loading the kernel message, screen goes blank. The screen resolution is 800x480, in attach the pdf specs. Info: the official asus image with kernel 4.4 works, but it is not an option for me as I don't want to use debian buster. Please help. Thank you very much. Bogdan WF50FSYFGDHNV.pdf

• 0

  Reputation Points

• 13 replies
• 7.3k views
• 2 followers

jock

November 14, 20241 yr

`ls /dev` is not showing mmcblk1. I have Armbian Ubuntu install that may have been messed around with and is not showing /dev/mmcblk1, where as a fresh uSCDCard install is.

• 0

  Reputation Points

• 13 replies
• 4.2k views
• 2 followers

AaronNGray

July 21, 20251 yr

hello , im a 0 in linux , i have orange 5 with mvme , i folowed how to for boot directly to mvme , the how to made me delete the spi flash. all was good, o5 boot on mvme succesfully but at each reboot , my hardware have new mac adress. any one can show me what to do step by step ? i used : Joshua-Riek/ubuntu-orange-pi5: Ubuntu 22.04 LTS for the Orange Pi5 ( desktop & serveur ) Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110.img.xz ubuntu serveur 23.04 ( 64 ) it's the same on all , boot one time i have mac adress , reboot = new mac adress i cant fix ip localy , so i think when i deleted spi flash , may be deleted…

• 0

  Reputation Points

• 13 replies
• 12.2k views
• 1 follower

Turbine

December 2, 20232 yr

Hi there. I just got my hands on a brand new 5T with 24GB of RAM and installed Armbian 26.04 minimal on it (on an SD card - no eMMC on this board). I immediately put it to use running CI jobs, however started seeing segfaults and things almost straight away. Current power source is the Radxa 60W power supply. Currently passively cooled (with the Radxa heat sink). Hasn't gone over 70º in the last 24 hours, even when maxxed out compiling rust packages. Here's information about the board: james@kassandra:~$ cat /proc/device-tree/model Radxa ROCK 5Tjames@kassandra:~$ james@kassandra:~$ dpkg -l | grep '^ii linux-' ii linux-base …

• 0

  Reputation Points

• 13 replies
• 2.7k views

jamesharton

May 11May 11

I Installed this image and it works fine. Sadly the build in WiFi module is not working. I now use an external wifi dongle. What could be the problem here? Ernst-Jan

• 0

  Reputation Points

• 13 replies
• 1.9k views
• 1 follower

eselarm

July 23Jul 23

It seems that If I use the mainline kernel Ethernet does not work, in the sense that it doesn't even get initialized. ip addr will only show the loopback interface, and the kernel log will show this regarding the ethernet port. Could it be a device tree issue? [ 6.867997] rk_gmac-dwmac ff540000.ethernet: PTP uses main clock [ 6.868097] rk_gmac-dwmac ff540000.ethernet: Linked as a consumer to regulator.5 [ 6.868103] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input). [ 6.868112] rk_gmac-dwmac ff540000.ethernet: TX delay(0x25). [ 6.868118] rk_gmac-dwmac ff540000.ethernet: RX delay(0x11). [ 6.868126] rk_gmac-dwmac ff540000.ethernet: integr…

• 0

  Reputation Points

• 13 replies
• 8.5k views
• 2 followers

jpegxguy

April 8, 20197 yr

I know this sounds strange, but I cannot get any of the images to boot. I have an R3S non-LTS + SD card. It works well with the stock images from FriendlyElec, but none of the Armbian images I tried will boot. I tried different tools to write the SD (BalenaEtcher, USBImager, Rufus), but nothing changed. When I tried to read the SD card with Armbian on my x86 laptop running Debian, the system didn’t recognize any proper partitions (maybe that’s normal, maybe not—I don’t know). But when I write an Armbian image for Allwinner NanoPi, the partitions are detected correctly. And finally, I can’t connect to the debug UART, so I can’t get any logs. I feel…

• 0

  Reputation Points

• 13 replies
• 6.8k views
• 2 followers

Vlad Kuzin

August 23, 20251 yr

Hello, I've recently bought a rock 5B plus. I have a brand new crucial P310 nvme 1TB with the goal to boot from it. As the title says, sometimes the nvme drive is properly detected, sometimes not. (Everytime the controller is visible in lspci, but only sometimes shows in lsblk). When the drive is properly detected, I can write to it and it works fine, without issues. I've noticed that it is more likely to be detected on a cold boot (ie. if I turn off the power and come back the next day, the first time it will probably show up). I have the official radxa 65w PD power adapter (although I've also tried a lot more during the proc…

• 1

  Reputation Points

• 13 replies
• 7.5k views
• 1 follower

eselarm

August 27, 20251 yr

I'd like to add hardware acceleration for my Orange PI 5 Plus, i've installed ` apt install -y clinfo` on the host (armbian) docker exec -it jellyfin /usr/lib/jellyfin-ffmpeg/ffmpeg -v debug -init_hw_device rkmpp=rk -init_hw_device opencl=ocl@rk ffmpeg version 6.0.1-Jellyfin Copyright (c) 2000-2023 the FFmpeg developers built with gcc 12 (Debian 12.2.0-14) configuration: --prefix=/usr/lib/jellyfin-ffmpeg --target-os=linux --extra-version=Jellyfin --disable-doc --disable-ffplay --disable-ptx-compression --disable-static --disable-libxcb --disable-sdl2 --disable-xlib --enable-lto --enable-gpl --enable-version3 --enable-shared --enable-gmp --enable-gnutls …

• 0

  Reputation Points

• 13 replies
• 8.7k views
• 2 followers

ozacas

September 12, 20242 yr

Hello, I have installed the Armbian 26.2 minimal IOT image based on Debian 13 Trixie - with the 6.18.x kernel - and I noticed the USB2 port (the single, vertical port next to the Ethernet port) is not working. Is this a limitation of the mainstream kernel (6.18.x) - i.e. does this work only with the vendor kernel (6.1.x) ? NB: I upgraded to 6.19 using the 'edge' kernel, but I'm seeing the same behavior. Here's the armbianmonitor outpur - https://paste.armbian.com/raw/udefojuxuk

• 1

  Reputation Points

• 13 replies
• 3.6k views
• 1 follower

deskwizard

August 16Aug 16

RTL8852BE is the official recommended Wifi module for Orange Pie 5 PLUS, but it is not available in Armbian 24.5.1 Linux Vendor Kernel 6.1 without a driver module. Hope the official driver will be added to the 6.1 kernel. Thanks.

• 1

  Reputation Points

• 13 replies
• 16.5k views
• 2 followers

bolet75

July 15, 20242 yr

Good afternoon everyone. Please help me with my problem. I have a Radha board zero 3w and I use the Armbian distrib. 24.8.1 . Everything works fine, except that I can't activate SPI. In the Armbian-config menu there is no hardware section (I tried different flash cards and Armbian versions, the problem persists), I also tried to edit the armbianEnv.txt and add overlays there, but I also did not have success. Tell me what else I can try. Activation works on the native distribution radxa debian.

• 0

  Reputation Points

• 13 replies
• 12.5k views
• 1 follower

maximilian fletkar

October 2, 20242 yr

Hi I was struggling to find the right package for my Tinkerboard. I needed a reasonably powerful 24x7 appliance that could provide torrent downloading, wifi hotspot, a shared network drive and a LMS box. After trying out the Asus effort and DietPi - both with severe issues) I landed on Armbian and it seems to have everything going for it but the LMS install just does not work. I am a Linux newbie, I know my way around Windows and a GUI, and used the instructions here and a few other places to successfully set up the hotspot and the sharing and automounting of large USB drives. It took me the better part of 6 hours just to figure all of that out (j…

• 1

  Reputation Points

• 13 replies
• 10.8k views
• 1 follower

Sangram

January 28, 20188 yr

I searched & tried all materials I can find, trying to set up FFmpeg to work with hardware acceleration on Orange Pi 5. But it did NOT work. Anyone else succeeds in using GPU hardware acceleration to encode/transcode video on Orange Pi 5 using FFmpeg? (or using gstreamer?) Could you please share with me the way to do it? Thank you very much indeed!

• 1

  Reputation Points

• 13 replies
• 47.9k views
• 1 follower

jyce

July 3, 20242 yr

Hi! I am looking into OdroidM1 network performance with kernel 6.6.47-current-rockchip64 ( 24.8.1 ) For some reason network performance is x10 faster (upstream) in bookworm and noble, when compared to jammy. Downstream performance is fine, delivering the same performance in jammy and the other distributions. Since all of them are using the same kernel, I assume that there must be some configuration that jammy is missing, or? Any idea about what could be going on?

• 1

  Reputation Points

• 12 replies
• 5.3k views
• 2 followers

rvalle

September 18, 20242 yr

I have an Orange Pi 5 (16GB RAM) running Armbian Jammy with the latest updates installed. I am booting from NVMe and when it boots successfully it runs flawlessly without issue. The problem occurs when I reboot -- the majority of the time it does not boot up successfully. Sometimes when it boots I only see the red light (and no green light), and other times I will see the green light flash like normal, yet the external hard drive does not spin up or mount properly. This results in me needing to power down the Orange Pi 5 and try again. Eventually it will boot up successfully (along with the external HDD) and then everything is good; that is, until the next time I have to …

• 0

  Reputation Points

• 12 replies
• 8.5k views
• 1 follower

etho201

February 8, 20233 yr

This is a last-ditch effort to figure out how we can continue to build our project on top of Armbian. Goal We are building an appliance on the RockPro64 board, with eMMC and an PCIe SSD attached, using a custom-built Armbian Ubuntu 18.04 image with extensive post-configuration (packages, appliacations, overlayroot...) within the boot process. The image is then processed by Mender to create a true dual-root filesystem over-the-air update system with fallback (we invested a lot of resources to extend Mender for Armbian and RockPro64). This build process works perfectly and is exactly what we need. Issue The reliability, however, is bad. In …

• 1

  Reputation Points

• 12 replies
• 7.8k views
• 2 followers

soerenderfor

October 18, 20205 yr

Hi all, Testing this OP5, got a standard M2 NVMe SSD (this works on my OP5Plus) I have formatted to exFAT with windows, inserted on the OP5, loaded ArmbianOS on MicroSD, it boots fine but I cant get it to show the nvme drive using fdisk -l or lsblk It seem like its not detecting the m2 nvme ssd at all.. little help please ?

• 0

  Reputation Points

• 12 replies
• 10.8k views
• 1 follower

zjd

May 9May 9

root@calypso:~# uname -a Linux calypso 6.12.0-current-rockchip-rk3588 #3 SMP PREEMPT Sun Nov 17 22:15:08 UTC 2024 aarch64 GNU/Linux cat /proc/asound/cards 0 [Audio ]: USB-Audio - USB Audio Bluetrum USB Audio at usb-xhci-hcd.1.auto-1, full speed 1 [rk3588es8316 ]: rk3588-es8316 - rk3588-es8316 rk3588-es8316 HDMI itself works perfect, monitor and cable tested for video and sound OK Both audio cards work with alsa - pulseaudio but no HDMI sound. Any suggestions how tho get the hdmi audio cards for HDMI0 and HDMI1 How to enable the HDMI sound driver? Thanks…

• 0

  Reputation Points

• 12 replies
• 7.3k views

Wilhelm Moser

January 24, 20251 yr

Hello! First time poster, long time admirer. I've been unable to get ANY of the 6.10.x images to boot off SD card (Sandisk Extreme) for the Orange Pi 5 Plus. Specific images which are not working for me: Armbian_24.8.0-trunk.472_Orangepi5-plus_noble_edge_6.10.2_gnome-kisak_desktop.img.xz Armbian_24.5.5_Orangepi5-plus_noble_edge_6.10.1_gnome-kisak_desktop.img.xz Armbian_24.8.0-trunk.472_Orangepi5-plus_trixie_edge_6.10.2_minimal.img.xz Has anybody else had better luck?

• 0

  Reputation Points

• 12 replies
• 10.2k views

Avatar Ng

September 6, 20242 yr

I am considering to buy a RK3399 dev board and use USB 3.0 peripheral mode to transfer data to/from another host PC. It may be used as USB CDC/Eth or RNDIS device, or a MTP device. We hope the transfer rate could be well over 1Gbps, the higher, the better. So has anybody ever benchmarked RK3399 USB in peripheral mode? Such as the highest iperf transfer rate in CDC/Eth or RNDIS mode?

• 1

  Reputation Points

• 12 replies
• 12.3k views

haajee

August 1, 20206 yr

Hi everyone, I need to enable the csi camera and i2c port on my zero3 development board. When I click on the management overlay, an error occurs. Is there any solution?

• 0

  Reputation Points

• 12 replies
• 9.9k views
• 1 follower

opi-5-plus-user

October 26, 2025Oct 26

Hello again, We're already aware of the existing issues with kernel 6 and the audio on the RK3308B. In this case, it fails again in the latest versions... Alsamixer detects the audio card and even shows it in arecord -L or arecord -l, but when trying to record, the error appears: "arecord: set_params:1416: unable to install hw params" The command applied is: arecord -c 2 -r 192000 -f S32_LE test.wav Although if I leave it without parameters to see what it does, it throws the same error, even if I specify the hardware... In the previous kernel (I think it was 6.12.11 (with the u-boot issue in the previous post), the audio worked per…

• 1

  Reputation Points

• 12 replies
• 5.4k views

Igor

July 8, 20251 yr

Hi guys, I got a SPIdev overlay to work on the rock S0, figured I'd just share it here for the record, since I could have used this info myself (I spent days trying to figure it out since I had no experience with device trees or whatnot). Basically, download the attached .dts file, then run sudo armbian-add-overlay rk3308-spi2-spidev.dts I also edited /boot/armbianEnv.txt and added this line, but I'm unsure if that's actually necessary? param_spidev_spi_bus=2 This worked on Armbian 24.5.1 Noble, creating /dev/spidev2.0. You can verify that it works using this tool: https://github.com/rm-hull/spidev-test The dts file is based on this one…

• 1

  Reputation Points

• 12 replies
• 6.5k views
• 1 follower

Cromefire_

November 23, 2025Nov 23

I was able to flash armbian bookworm cli to the ssd using balena etcher but when I boot the OPI5 from the sdcard and run lsbk it can only see the sdcard any ideas ...

• 0

  Reputation Points

• 12 replies
• 4.9k views

Werner

June 22, 20233 yr

I lost whole day yesterday to try boot with new images from Armbian download page - kernel 6.1 / kernel 6.8 bookworm/trixi and none boots... If I take Ubuntu or Debian image I have no problem to boot from. Do you have the same?

• 1

  Reputation Points

• 12 replies
• 5.4k views

Werner

May 31, 20242 yr

I'm using Armbian on a Tinker Board S. I did the installation back when the 4.4 kernel was still the default one. I expected that I'd get the newer 4.19 kernel by using 'apt update && apt dist-upgrade' at some point as it would become the new stable. This does not seem to be the case however, as I see the new downloads use 4.19 by default, but the stable package still points to a 4.4 kernel. Is it recommended to just move up by installing the kernel package with the next suffix or are there still reasons to wait with upgrading?

• 0

  Reputation Points

• 12 replies
• 7.4k views
• 1 follower

sfx2000

May 4, 20197 yr

I am testing RK3288 with ubuntu 20.04 (gnome) btw NICE And I have some problems with panfrost and I am looking for anybody with RK3288 device that can confirm or not same behavior. Problem is that when I switch GPU to 600MHz sudo bash -c 'echo "userspace" > /sys/class/drm/card1/device/devfreq/ffa30000.gpu/governor' sudo bash -c 'echo "600000000" > /sys/class/drm/card1/device/devfreq/ffa30000.gpu/userspace/set_freq' and when I run glmark2-es2 or glmark2-es2-wayland I start to see https://pastebin.com/NuYqHdxH in kernel.log So I made bugreport(https://gitlab.freedesktop.org/mesa/mesa/-/issues/2693) for panfrost and the…

• 1

  Reputation Points

• 12 replies
• 10.6k views
• 2 followers

Myy

August 16, 20206 yr

Hi guys, I would like to make a support request for the: NanoPi-R76S ($49): https://www.friendlyelec.com/index.php?route=product/product&product_id=308 Thank you for considering. Dantes

• 1

  Reputation Points

• 12 replies
• 4.3k views

Dantes

September 11, 20251 yr

Expected Behavior: I am able to enter sleep mode, either graphically or using systemctl suspend, and then wake from sleep mode by typing on the keyboard or pressing the power button Current Behavior: The system appears to enter sleep fine, but once in sleep pressing the power button or pressing buttons on the keyboard seems to do nothing (pressing keys on my keyboard causes it to light up, however my mouse does not light up). The display remains blank and the green led does not blink. I have to do a forced shutdown by holding the power button or unplugging the power supply. Note: the behavior is the same no matter if I suspend from a desktop sessio…

• 0

  Reputation Points

• 12 replies
• 9.3k views

Catloaf2019

May 6, 20233 yr

Hey, I’m running armbian on a tinkerboard and I need to connect to a CAN-bus. Apparently the usual Linux CAN-kernel-modules aren’t shipped with armbian, so I guess I’ll have to add them manually somehow. I`ve been trying to do that for two days now without any luck. I’ve been trying to follow the steps described in other forums, but it haven’t helped. I really just want to add the necessary modules to my existing kernel. Any ideas?

• 1

  Reputation Points

• 11 replies
• 8.2k views

Marius Brataas

February 27, 20188 yr

Hi, I can not get the back panel audio working, the HDMI analog audio to my display works, but changing the output to Analog out is not working. Any suggestions as to where I can start to troubleshoot? Thanks!

• 0

  Reputation Points

• 11 replies
• 4.7k views
• 1 follower

prahal

May 16, 20251 yr

Hy, I have a Tinkerboard with armbian ( debian jessie). When I put behind my fiber router, and i do a speed test i have : With iperf3 ==> download : 980M and upload : 240M with speedtest-cli ==> More or less Results. I wanted to conenct my Asus's card behind the ONT(Optical Termination Boxes) i can connect with pppoe or dhcp. And in pppoe or dhcp my speed test show this : With iperf3 ==> download : 110M and upload : 80M with speedtest-cli ==> More or less Results. I have tested with anorther Board, bananapi mé with Bananian and i have the same Results if I put behin…

• 1

  Reputation Points

• 11 replies
• 7.6k views

Ren Ping

February 20, 20197 yr

please, helpme with thist message in boot :

• 0

  Reputation Points

• 11 replies
• 7.8k views
• 2 followers

haajee

October 21, 20241 yr

Hi there, I pourchased OPi5 (not preferred OPi5 Pro, because of Armbian lacking support), flashed Debian 24.8.1_bookworm_6.10.6_cinnamon_backported_mesa_desktop, configured (user, switch to static IP, user). Worked OK. Now, ssh'ing into showed "113 packages upgrade". Did "apt upgrade". Download OK, but when applying apgrade process hung twice: - once on "configuring libc", had to power off, then restarted (after an apt-get suggested in response to apt upgrade). Upgrade hung second time (no progress on bottom bar for hours, no new ssh session). - twice was on "configuring udev". After this, board is almost dead: - boots to anima…

• 0

  Reputation Points

• 11 replies
• 4k views
• 1 follower

laurentppol

November 27, 20241 yr

running 24.8.3, and Armbian-install's screen looks like this: Current root: UUID=117b851b-2be0-4bb7-8572-7edce1ef7375 SD card (/dev/mmcblk1) 1 Boot from SD - system on SATA, USB or NVMe 2 Boot from - system on 3 Boot from - system on SATA, USB or NVMe 5 Install/Update the bootloader on SD card (/dev/mmcblk1) I have a µSD card inserted and a 4gb eMMC, but it looks like the names of these devices are missing?

• 1

  Reputation Points

• 11 replies
• 4.6k views
• 1 follower

Meestor_X

January 1, 20251 yr

Hi! I connect my 1366x768 monitor to Tinkerboard, but resolution sets to 1280x720. $ xrandr Screen 0: minimum 320 x 200, current 1280 x 720, maximum 8192 x 8192 HDMI-1 connected 1280x720+0+0 (normal left inverted right x axis y axis) 410mm x 230mm 1920x1080 60.00 + 1280x720 60.00* 720x480 60.00 Yes, i tried set timings manualy. I set native from edid: Modeline "Mode 0" 85.50 1366 1436 1579 1792 768 771 774 798 +hsync +vsync But after applying this modeline: - monitor detects 1280x720 resolution instead of 1366x768 - crops image as 1024x768 - have many noises and waves on screen... very unstable image (pixel clock 8…

• 1

  Reputation Points

• 11 replies
• 10.2k views
• 1 follower

berin

April 7, 20197 yr

Greetings, After setting my tinkerboard pins 22 and 24 as an Inputs, they reverts to being an output pin on HIgh after around 30 seconds. What is the cause of this? Is this some kind of feature. I don't have this happen on any other pin other than these 2. iomari

• 0

  Reputation Points

• 11 replies
• 5.9k views
• 1 follower

iomari

September 25, 20197 yr

Hi. I installed Armbian_20.02.1_Tinkerboard_bionic_current_5.4.20_desktop on my TinkerBoard (not S) and get weird screen state (white, then growing black circle in the middle). I tried Armbian_20.02.1_Tinkerboard_bionic_legacy_4.4.213_desktop and it works very good, but I still want to test vulkan driver, so I updated only kernel to 4.19 (install linux-image-next-rockchip, linux-header-next-rockchip, linux-dtb-next-rockchip and delete 3 old packages). After reboot I got same screen. Is it known bug? Can it be related, that I'm using HDMI-to-VGA adapter? Can you help me to fix it or get usefull logs?

• 0

  Reputation Points

• 11 replies
• 6.4k views

Myy

April 19, 20206 yr

hi , i installed Armbian 22.11 Jammy minimal image for headless console only usage. uname -a Linux tinkerboard 5.15.80-rockchip #22.11.1 SMP PREEMPT Wed Nov 30 11:05:19 UTC 2022 armv7l armv7l armv7l GNU/Linux i installed teamviewer and if device rebooted with hdmi connected, i am able to use teamviewer and teamviewer shows shell output but when rebooted without hdmi cable connected, teamviewer seems working on device , but cant connect it.. here is teamviewer info TeamViewer 15.37.3 (DEB) TeamViewer ID: 1374960804 teamviewerd status ● teamviewerd.serv…

• 0

  Reputation Points

• 11 replies
• 5.4k views
• 3 followers

atone

January 10, 20233 yr

Has anybody seen this message at boot: [ 5.352826] CPU4: failed to come online [ 5.352835] CPU4: failed in unknown state : 0x0 [ 10.481328] CPU5: failed to come online [ 10.481336] CPU5: failed in unknown state : 0x0 Then, the A72 cores don't show up (unsurprisingly since these are the two cores that somehow did not come online). On top of that, the kernel throws a backtrace (related to sound if I understand correctly): ------------[ cut here ]------------ [ 13.014782] WARNING: CPU: 3 PID: 1 at kernel/irq/manage.c:1990 request_threaded_irq+0x144/0x180 [ 13.014784] Modules linked in: [ 13.014793] CPU: 3 PID: 1 Comm: swapper…

• 0

  Reputation Points

• 11 replies
• 6.4k views
• 1 follower

Myy

April 17, 20206 yr

Hi, I have had some issues trying to boot from eMMC with the last version of Armbian (kernel v5.4) while it's working perfectly on Armbian with a v4.4 kernel. Images not working: https://dl.armbian.com/rockpro64/archive/Armbian_20.05.2_Rockpro64_bionic_current_5.4.43.img.xz https://dl.armbian.com/rockpro64/archive/Armbian_20.05.4_Rockpro64_focal_current_5.4.46.img.xz Working image: https://dl.armbian.com/_old/rockpro64/archive/Armbian_5.98_Rockpro64_Debian_buster_default_4.4.192.7z I though I messed up with the SPI or the eMMC card but after trying all I could, it finally worked using an old version of Armbian…

• 1

  Reputation Points

• 11 replies
• 10.7k views
• 1 follower

denni_isl

March 9, 20224 yr

Unfortunately, there seems not yet to be an area in this forum for NanoPi R6C/S, so here we go ... Here is the default Armbian /etc/udev/rules.d/70-persistent-net.rules SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", KERNELS=="fe1c0000.ethernet", NAME:="wan" SUBSYSTEM=="net", ACTION=="add", DRIVERS=="r8169", KERNELS=="0003:31:00.0", NAME:="lan1" SUBSYSTEM=="net", ACTION=="add", DRIVERS=="r8169", KERNELS=="0004:41:00.0", NAME:="lan2" This does not match up with the labels on the case! Here is the correct config we have updated and tested on a NanoPi R6S at Afritic Group: SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*"…

• 0

  Reputation Points

• 11 replies
• 4.7k views

eselarm

July 23, 20251 yr

hi i can not get my ethernet to work with img Armbian_5.72_Tinkerboard_Debian_stretch_next_4.19.16_desktop me lost !

• 1

  Reputation Points

• 11 replies
• 5.4k views

chrish

January 19, 20197 yr

I am trying to get a USB Serial adapter working on my Asus Tinkerboard running Armbian. if i lsusb i get: root@tinkerboard:~# lsusb Bus 001 Device 006: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port however no /dev/ttyUSB0 shows up. Is there an armbian kernel for the asus tinkerboard with usb serial support?

• 1

  Reputation Points

• 11 replies
• 12.2k views
• 1 follower

odoll

February 13, 20197 yr

When the ODROID-M1 is setup to boot from SPI with the system installed on a M2 ssd, power loss seems to lead to an unbootable system. Once an SD card with armbian is inserted and the system is booted through the recovery button once, logged in* and then shutdown normally, the system boots again from SPI. * Without login and regular shutdown of the system booted from sd card, the issue remains I have observed and reproduced this issue several times in the last year. In my case the M1 is connected to a power strip that turns on and off the multiple devices. When I forget to unplug the M1 and it gets turned on and off several times over a day …

• 0

  Reputation Points

• 11 replies
• 6.8k views

tstalker

October 30, 2025Oct 30