Amlogic meson

Hi guys, My N2+ just arrived and I was able to install a Debian Bookworm (EDGE) image I built onto it (both to a SD card and an EMMC card) The selector switch is set to boot from MMC. Armbian fires up nice from the SD card but it does not boot from the EMMC. I can see the Drive with fdisk so I guess I need to copy the boot image onto it. (Its /dev/zram1) This is the first step towards building a PREEMPT_RT image so I was excited to see it sorta works! Any help or ideas would be appreciated.

• 0

  Reputation Points

• 1 reply
• 3.2k views
• 2 followers

rodw

February 10, 20233 yr

The zfs-dkms included in Armbian_22.11.1_Odroidhc4_jammy in version 2.1.4 is to old for 5.19.17 kernel. It should be 2.1.6 like in Armbian_22.08.7. Loading new zfs-2.1.4 DKMS files... Building for 5.19.17-meson64 Building initial module for 5.19.17-meson64 configure: error: *** None of the expected "blk_queue_discard" interfaces were detected. *** This may be because your kernel version is newer than what is *** supported, or you are using a patched custom kernel with *** incompatible modifications. *** *** ZFS Version: zfs-2.1.4-0ubuntu0.1 *** Compatible Kernels: 3.10 - 5.17 http://paste.debian.ne…

• 1

  Reputation Points

• 4 replies
• 3.6k views

drikus

January 24, 20233 yr

Hello, I'll start by saying I'm new at those things. I have recently bought a "Le Potato" board. I was trying to install Lakka (via raccomanded link). When I plugged in the micro SD, the power, the HDMI out ecc, nothing happened other than two led turning on (red and blue). What could have gone wrong? Thanks in advance

• 0

  Reputation Points

• 1 reply
• 2.8k views

NicoD

February 22, 20233 yr

Good morning everyone. My problem is that I had armbian installed in emmc and using armbian config I changed it to usb but I did not update the boot to sd and when I restart it only shows what I put in the photo and it remains black. Is there any way to fix it. By pressing reset with the HDMI unplugged it tries to start but stays in initramfs. Thank you

• 0

  Reputation Points

• 0 replies
• 2.3k views

fatuo

April 26, 20242 yr

EDIT: Please don't trust in the numbers appearing at the top of this thread. Obviously there were bootloader/firmware issues that needed to be resolved and afterwards Potato performance will be somewhat higher. Since I didn't find numbers may I ask owners of the device ( @Igor, @TonyMac32 ?) to run 4 quick benchmarks? Two times openssl, 7-zip and tinymembench. Please comment also which clockspeeds and which distro you used (Xenial preferred). Thanks!

• 1

  Reputation Points

• 30 replies
• 18.1k views

Da Xue

November 11, 20178 yr

Hello everyone, Upgrading from distro isn't supported officially but I tried it anyways and thought I should share my findings. In short, it worked for me. Others have reported issues so maybe we can figure out what causes these issues. My N2+ is fairly vanilla, so I didn't heavily modify it. Running 5.10.x kernel since that is recommended for de N2+ Step 1. Fully upgrade your system on Focal sudo apt-get update sudo apt-get upgrade sudo apt-get dist-upgrade Step 2. Shutdown you N2+ and make an image backup of your emmc using dd or Win32DiskImager in case something goes wrong Step 3. Boot up your N2+ a…

• 1

  Reputation Points

• 7 replies
• 11.3k views
• 1 follower

bthoven

June 30, 20251 yr

Armbian boot logo shows and also on shutdown.... just doesn't want to display the desktop. Gnome desktop image. 6.1.50-current-meson6 #2 SMP PREEMPT Wed Aug 30 14:11:13 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux

• 0

  Reputation Points

• 2 replies
• 3.1k views

chall88

November 2, 20232 yr

Hi guys I'm new to this type of computer. I recently got the Le Potato and have tried flashing the armbian package for it with USBimager and Balena and still get no boot. I was able to use the Raspberry PI imager and got Raspbian installed. I'm not sure what exactly is going wrong. I am using a Sandisk Extreme V1 32g but was able to get raspbian on a Samsung Evo select 256g.

• 0

  Reputation Points

• 1 reply
• 2.7k views

TonyMac32

November 10, 20223 yr

Good day! I have a Banana pi m2s with Amlogic A311D, 4GB RAM and 16GB emmc. Official images from Banana pi work on this device (both emmc and SD card). The problem is when I try to install Armbian on SD card - using BalenaEtcher on Windows / Disk tool on Ubuntu Mate: - the m2s either doesn't boot (when Armbian is written on emmc memory) - or m2s boots from emmc storage (when Armbian is written on SD Card) SD card has boot priority over emmc and works fine with official .img from bananapi. I see all written files on SD card after using Balena Etcher. The difference from official images is that boot folder in official …

• 0

  Reputation Points

• 4 replies
• 3.4k views
• 1 follower

Shtopor

July 22, 20242 yr

1 2 ### Activated 1 lzo-rle zram swap devices with 1816 MB each 3 4 ### Activated Armbian ramlog partition with zstd compression 5 6 ### Activated 1 lzo-rle zram swap devices with 1816 MB each 7 8 ### Activated Armbian ramlog partition with zstd compression 9 10 Sun 28 Mar 2021 04:42:10 PM CEST | Odroid N2 | 21.02.3 | arm64 | aarch64 | 5.10.21-meson64 11 12 ### dmesg: 13 14 [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] 15 [ 0.000000] Linux version 5.10.21-meson64 (root@hirsute) (aarch64-linux-gnu-gcc (G…

• 0

  Reputation Points

• 2 replies
• 5.9k views

Arne Hübner

April 18, 20215 yr

I have a ToupTek MU300 USB2 camera that I was trying to get working with my LePotato. The camera does not have native kernel support, but the manufacturer provides an SDK with a pre-compiled lib for x86/arm, and additionally I have a kernel module which works on X86/X64 with this camera as well as userspace libusb based code to access the camera. The camera is very sensitive to having buffers available during bulk transfer, otherwise the image will be corrupted. Generally synchronous bulk transfer is not fast enough, and requires multiple buffers supplied in asynchronous mode. On x86-64 and Rpi3/4, everything works as expected. I can grab im…

• 1

  Reputation Points

• 2 replies
• 3.5k views
• 1 follower

PhracturedBlue

December 24, 20205 yr

Hi there, I have an overlay available for Odroid C4 (Kernel 6.6.51), which needs some testing in the field. It supports 12MHz operation max on the pins 19, 21, 23 and 24 on the GPIO header. In case you have a test case for that, let me know, and I can provide things to you. Michael

• 0

  Reputation Points

• 0 replies
• 2.1k views

mboehmer

September 16, 20242 yr

Hello everyone! I bought Khadas VIM1 board and Official FAN(Ali Link) but seems to be not working with Armbian Bullseye, how I can run it? Thanks.

• 1

  Reputation Points

• 8 replies
• 5.4k views

noisyislands

January 6, 20233 yr

I am having trouble installing specific hardware dkms because the dkms requires the linux header files for the installed kernel version which are not available or do not exist. Armbian 23.05.1 Ubuntu 22.04 desktop version is build with kernel 6.6.63 but an apt search for the relevant headers finds none. Headers exist for 6.2, 6.5 and 6.8 but not for 6.6. How can I address this?

• 1

  Reputation Points

• 5 replies
• 4.8k views

Walter Zambotti

February 28, 20251 yr

Hi Installed Armbian_25.2.3_Odroidhc4_bookworm_current_6.12.17-homeassistant_minimal.img an a HC4 and noticed that USB doesn't work. lshw shows: *-usbhost:0 product: xHCI Host Controller vendor: Linux 6.12.17-current-meson64 xhci-hcd physical id: 1 bus info: usb@1 logical name: usb1 version: 6.12 capabilities: usb-2.00 configuration: driver=hub slots=2 speed=480Mbit/s *-usbhost:1 product: xHCI Host Controller vendor: Linux 6.12.17-current-meson64 xhci-hcd physical id: 2 bus info: usb@2 logical name: usb2 version: 6.12 …

• 0

  Reputation Points

• 6 replies
• 5.3k views

Igor

March 20, 20251 yr

So, first of all, pretty much a newbie here. I'm trying to add protonvpn to my HC4. I was able to do it with Ubuntu Mate (from the HC4 webpage) on the same hardware, so I'm pretty sure it's possible on Armbian. To be fair, the ProtonVPN website says that raspbian is not supported (and I assume they meant to say ARM) but I have been able to get it to work on Mate, and the problem on Armbian seems to be the Public Key and nothing else. After installation, the app will start, but won't work, so some successful compiling for ARM seems to be happening. What I did: - Downloaded the deb file for Debian based stable release - Tried GDebi and Apt, but dpkg wo…

• 0

  Reputation Points

• 0 replies
• 3.9k views
• 1 follower

natsbar

June 1, 20224 yr

I have an Odroid-N2+ and I would like very much to Armbian on it. However, when I run lspcu I see that mitigations for hardware side channel attacks are missing: $ lscpu Architecture: aarch64 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 6 On-line CPU(s) list: 0-5 Vendor ID: ARM Model name: Cortex-A53 Model: 4 Thread(s) per core: 1 Core(s) per socket: 2 Socket(s): 1 Stepping: r0p4 CPU max MHz: 2016.0000 CPU min MHz: 1000.0000 BogoMIPS: 48.00 Flags: fp asimd evtstrm aes …

• 0

  Reputation Points

• 1 reply
• 3.1k views

Igor

August 19, 20224 yr

I need a UART in my work. Added uartC overlay via armbian-config (UART_EE_C - /dev/ttyAML4) However, after booting, the device /dev/ttyAML4 does not appear. The download log contains the following information: Using the kernel-provided DT meson-uartC.dtbo overlay fdt_overlay_apply() error: FDT_ERR_BADMAGIC base fdt has no node /__symbols__ make sure you compile with -@ Error applying DT overlays, restoring original DT I would be grateful for any help!

• 0

  Reputation Points

• 0 replies
• 2.3k views

diaamant

April 12, 20233 yr

I think it would make sense to rename the forum section here from "Amlogic S905(x)" to "Amlogic". It would make much more sense for me to talk here for example about the Armbian port of the Odroid C0/C1/C1+ (Amlogic S805) then in any other forum section.

• 0

  Reputation Points

• 1 reply
• 3.8k views

Igor

November 28, 20187 yr

If I connected the serial port with my device through GPIO pin 8 and 10 (UART_AO_A_TXD, UART_AO_A_RXD), the Radxa Zero with " Armbian 23.02.2 Jammy" failed to boot. If I removed my device from the serial port, zero can boot. After booting, I connected my device to the UART port, it worked well through /dev/ttyAML0. Any suggestions? Many thanks!

• 0

  Reputation Points

• 3 replies
• 3.6k views

kayanite

October 19, 20232 yr

bananaoi-m5, Armbian 25.8.1 bookworm installed I can login via ssh as first user, gene, and sudo -i just fine. Buuuttttttt, at reboot the local screen ask's for the pw for amandabackup, a user lock down tightly which has never had a pw assigned. as its intended to be pw--less for the amanda backup system. What miss-configure can cause this????? Also I ordered 2 more of the keyboard/mouse combo''s which are the same as I'm using with a similar install for klipper running a 3d printer, but the dongle doesn't init when plugged in ack dmesg output, refusing its on discovery assigned address. So no keyboard/mouse is locally possible. I'll unpack the 2nd identical…

• 0

  Reputation Points

• 1 reply
• 1.8k views

gene1934

August 29, 20251 yr

As of 2025-12-01, current 'Armbian 25.11.1 Trixie Minimal / IOT' lists as 'Kernel: 6.12.58, Size: 505 KB, Release date: Nov 22, 2025' and seems to have had problems on image generation. Please check when possible. Thanks in advance, pbg

• 1

  Reputation Points

• 8 replies
• 3.6k views
• 1 follower

pbg

December 2, 2025Dec 2

I know there is a template, but this board is already on the download page as unsupported, just ran a group of tests on it after building a full desktop image, I think we can move it to supported without any issues, the S805X is the same as an S905X with some things turned off, like comparing an H3 and an H2+. Pros: SPI contains u-boot, we don't have to do anything with that. Libre Computer updates the firmware periodically (available on their site) already supports USB boot, etc, and has a "press escape for menu" option, making it very difficult to brick. UMS mode is menu selectable (I feel like we need to look at this. I hav…

• 1

  Reputation Points

• 3 replies
• 5.5k views
• 1 follower

TonyMac32

November 24, 20196 yr

hy guys is it possible to boot the odroid c2 from usb? so i can connect a ssd (M.2 SATA) via usb connector and use this. thank you

• 0

  Reputation Points

• 1 reply
• 3.2k views

Igor

April 23, 20242 yr

Hello, I run armbian 20.08.3 on an Odroid N2 with a dongle wifi. I have upgraded the board from armbian-firmware full 20.08.3 to 20.08.4. After that the screen insn't recognize anymore (it's an AOC e2250Sda) and after some reboot it s doest start anymore. Have I to wait the nex update ? Thanks a lot

• 0

  Reputation Points

• 3 replies
• 4.7k views

abeille

September 25, 20206 yr

From time to time, I notice that the HC4 looses its IP address. journalctl then tells me: dhcp4 (eth0): selecting lease failed: -131 But I don't know the reason for it. Sometimes it happens after a reboot. Pulling the ethernet cable off and plugging it in again seems to help and after a few tries, the HC4 is reachable again. I'd be happy to give more information, but I don't know yet how to debug it. I noticed that /var/log (zram) sometimes gets full but I don't know if this is related…

• 1

  Reputation Points

• 5 replies
• 5.4k views

Igor

November 25, 20214 yr

Armbian_22.05.4_Odroidn2_jammy_current_5.10.123_xfce_desktop.img ... comes up with the Armbian logo and circling dots... But the dots go on for an hour and a half. Here's what /var/log/bootstrap.log looks like.

• 1

  Reputation Points

• 22 replies
• 8.2k views
• 1 follower

usual user

August 9, 20224 yr

Hi guys, I installed the latest Armbian (Buster) release for my Odroid HC4 and - after getting rid of Petitboot as that just wouldn't let me boot the image - it's working great so far. Only big problem I have is that it does not recognize any SATA devices, in neither of the two slots. I tried different HDDs / SSDs that I verified are recognized on a Windows PC and another Ubuntu PC. Did anyone get that working already? I assume the required Kernel drivers for the PCIe-Sata-chip are probably still missing. Many thanks and best regards Daniel

• 1

  Reputation Points

• 16 replies
• 14.4k views
• 1 follower

Yan Pashkovsky

July 24, 20242 yr

I've spent the entire morning trying to boot armbian on a vim 3 basic. It won't boot from sdcard. I erased the emmc with krescue, no change except now it doesn't boot anything, except the krescue sdcard. I put the armbian image on a USB stick and tried to flash it to emmc With krescue but krescue says it's an invalid vim 3 image. I verified the Sha and I also tried using the extracted dot img file. Which isn't recognized by krescue. How do I boot an sdcard or flash the emmc When none of these things work? The only thing that boots now is the krescue sdcard. What am I doing incorrectly? What else can I try?

• 1

  Reputation Points

• 37 replies
• 19.6k views
• 1 follower

Erica

June 8, 20242 yr

Hi, I am using Armbian (latest) image on Banana Pi CM4 and I don't have access to gpio493. I am getting the following error: And looks like gpiochip4xx is not available: When I modprobe this gpio number, I am getting following error: modprobe: FATAL: Module gpiochip493 not found in directory /lib/modules/6.7.2-edge-meson64 Could you please help, how can I enable gpio 493? Thanks

• 1

  Reputation Points

• 12 replies
• 5.1k views

Abhishek Chr

January 29, 20242 yr

I am trying the first releases of armbian on my new odroid n2 and would like also to test openmediavault which should be available with 3rd party option on armbian-config. But at the moment this software option is not available. Is there a reason for this, maybe the device is very new and not tested for the moment?

• 0

  Reputation Points

• 2 replies
• 4.2k views

Franky66

May 24, 20197 yr

Hello, I'm pretty new to Armbian and also to Odroid devices. I'm trying to use Armbian as main operating system (instead of official Ubuntu image). If I burn SD with official Ubuntu image, it work well, if I try to burn almost any of Armbian images for Odroid N2/N2+, I can't get them to work. I've tried theese images: Armbian 22.08.1 Bullseye Armbian 22.05.4 Bullseye Armbian 21.08.1 Bullseye Armbian 22.05.4 Jammy Armbian 22.05.4 Jammy Armbian 21.05.2 Hirsute Edge As per Ubuntu, I've downloaded them, burnt with BalenaEtcher on SD, put the SD in switched-off odroid, attach hdmi, lan, keyboard an…

• 0

  Reputation Points

• 0 replies
• 2.8k views
• 1 follower

Stefano Roncalli

September 2, 20224 yr

I am trying to use radxa-zero with HDMI CEC support on Armbian debian. I tried all different Armbian debian versions, lsmod never give me module cec So I took a look at images provided by radxa (https://github.com/radxa-build/radxa-zero/releases/tag/20220801-0213, not armbian ones), cec is loaded by default I think this is the key: /lib/modules/SOME_KERNEL/kernel/drivers/media/cec/core/cec.ko This is in their image but not /lib/modules/6.1.11-meson64 folder (I guess also not in other kernel versions) If that's the case, CEC should not work on any meson64 devices. I saw CONFIG_CEC_CORE=y is in config. btw, another p…

• 0

  Reputation Points

• 2 replies
• 3.4k views
• 1 follower

Igor

October 7, 20233 yr

Are there any plans of adding webcam drivers to the kernel modules for Le Potato? Specifically, I'm looking to use a uvc video webcam, but can't figure out how to compile it myself.

• 1

  Reputation Points

• 4 replies
• 4.7k views
• 1 follower

linuxgator

April 1, 20188 yr

When I try to do "apt upgrade" on a brand new SD Card that has been just flashed I get a "kernel panic". This is the whole error: https://paste.debian.net/1283664 And this is the armbianmonitor -U log: https://paste.debian.net/1283662/ The board runs fine with debian with 4.9.x kernel supplied by manufacturer. Armbian is the second image I try because I need a newer kernel. I'll try to find one that is less new. Thank you for your support! EDIT: I tried again without wifi and it worked flawlessly. I can't make it crash with a wired connection. I used the same wifi plug with Debian and I never had an error but may…

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

Alberto234329

June 20, 20233 yr

Hello, I have been using the Le Potato for a while, and was able to save Armbian on an eMMC and boot from it. Then I tried putting another OS onto it but now it's no longer able to boot or recognize the eMMC module even when I go to Armbian settings. Please help me be able to use it again to continue tinkering around with it. Thanks very much!

• 0

  Reputation Points

• 0 replies
• 2.4k views
• 1 follower

Kirill Sanchez

June 14, 20242 yr

Hello, I have tested Armbian with SD card without issue. I'm wondering if it's possible to do the same using SSD. SSD is much more reliable and faster than SD card. I can do it with the Ubuntu release from Odroid using petitboot, but it seems that Armbian isn't compatible with petitboot. Thank you

• 0

  Reputation Points

• 73 replies
• 49.6k views
• 2 followers

-hannes-

March 25, 20233 yr

Install of Armbian 21.02.2 Buster with Linux version 5.7.15-meson64 and gpiod package installed on the Odroid N2 does not work for gpiomon. The gpiod command gpioinfo and gpioget work fine. Gpiomon fails with message "No such device". Searching for hours I believe the issue is that interrupts have not been assigned to the gpiopins, so appropriate devices don't exist. Any information on when/how to get a fully functional gpiod and associated python package going. Python code using python3-libgpiod also fails on the line.request function with the same "No such device" error.

• 0

  Reputation Points

• 2 replies
• 5.2k views
• 1 follower

0n3man

February 24, 20215 yr

Hi, We're swapping the Khadas Fenix 4.9 and uboot v2015-01?? for the Armbian 5.10.y and corresponding mainline u-boot. In the "legacy" version we were able to use the u-boot script (then a dedicated boot.ini) for setting a gpio pin low like this gpio clear GPIOH_4 Unfortunately Armbian's mainline u-boot version does not recognize GPIOH_4 as a valid gpio pin name. Anyone able to help? Did the naming change? Gé

• 0

  Reputation Points

• 1 reply
• 3k views

gkkpch

October 18, 20223 yr

Placeholder for Libre Computer La Frite general topics Marked "Supported" as of Nov. 24, 2019 Reference pages: https://libre.computer/products/boards/aml-s805x-ac/ https://forum.loverpi.com/categories/libre-computer-aml-s805x-ac https://drive.google.com/file/d/1Dl3lLTs407OZ7HhPYjjlvDX2_FPfKHMr/view

• 0

  Reputation Points

• 0 replies
• 6.8k views
• 1 follower

TonyMac32

November 24, 20196 yr

Sorry if I ask, but I can't seem to find an actual definitive answer anywhere about this. Is there at the moment or will be in the future a way to have an hardware accelerated MATE desktop using armbian on le potato? And if there is/will be, what limitations does/would it have? (opengl/window compositing/video decoding/video encoding...) Thanks in advance

• 0

  Reputation Points

• 0 replies
• 3.9k views

Massimo Martelli

January 6, 20188 yr

I'm using the "Armbian 22.11.1 Lepotato jammy 5.19.17 xfce desktop" image which comes with lightdm windows manger and wayland xserver. I want to use https://github.com/debauchee/barrier but it does not support wayland, so I want to switch to xorg. So far I've tried installing xorg using apt and adding the following line to /etc/lightdm/lightdm.conf xserver-command=Xorg but when I do sudo systemctl restart lightdm the display manager hangs forever with blank screen and blinking cursor.

• 1

  Reputation Points

• 1 reply
• 4.2k views
• 1 follower

XENIZS

January 8, 20233 yr

I had another distro and power button nicely shut down the system and it doesn't with armbian. I have read some things about it but I'm not even sure if they apply to this board or they are updated, about acpi events, logind and AR100, and I've read the official schematics of the board. It seems the button is connected to ADC pins. I installed acpid but acpi_listen reports nothing. But evtest does! root@bananapim5:~# evtest /dev/input/by-path/platform-adc_keys-event Input driver version is 1.0.1 Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100 Input device name: "adc_keys" Supported events: Event type 0 (EV_SYN…

• 0

  Reputation Points

• 0 replies
• 2.4k views
• 1 follower

Alberto234329

June 21, 20233 yr

I've been trying to enable SPI on the board but have had no luck in this. I noticed that in the armbian-config there is no spi option. I have edited the armbianEnv.txt file to include orerlays = spi-spidev param_spidev_spi_bus = 0 I've tried changing the bus to 1 None of these actions have helped. Any advice would be greatly appreciated.

• 0

  Reputation Points

• 2 replies
• 4.5k views

smarttowers

September 18, 20224 yr

The images where applied with Balena etcher. Petitboot was removed as described. The PSU was included in the bundle (15V 4A). Odroid Ubuntu works fine. The boot process stops at: Booting kernel ... I tried the following Images (none of them works): Armbian Buster - mainline kernel 5.10.y Armbian Focal - mainline kernel 5.10.y What am i missing ? Any help appreciated.

• 0

  Reputation Points

• 1 reply
• 5.9k views

Werner

February 24, 20215 yr

I've tried a few images of the latest builds. None of them start. Odroid starts to power the screen and I see blinking lights, but screen goes dark and it seems to cycle like this. I use USB power for it and a powered hub (so basically no power output to USB dongles, etc.)

• 0

  Reputation Points

• 15 replies
• 10.9k views
• 2 followers

natural

May 5, 20233 yr

context ------------ Hardware: BPI CM4 on BPI CM4IO board OS: Armbian 24.11.1 Bookworm Minimal Build: https://dl.armbian.com/bananapicm4io/Bookworm_current_minimal problem ------------ How do i enable i2c2 so i can be able to use the following pins on the BPI CM4IO board for i2c pin 82 (GPIOX_17): (MUX UNCLAIMED) (GPIO UNCLAIMED) pin 83 (GPIOX_18): (MUX UNCLAIMED) periphs-banks:595 Previously on the ubuntu build all i had to do is add the following line to `/boot/env.txt` , `overlays="12c2"`, as stated in this doc https://wiki.banana-pi.org/Getting_Started_with_CM4#DTB_overlay 2. Update the overlays env in vfat /boot/env.txt to ena…

• 1

  Reputation Points

• 11 replies
• 9.2k views

c0rnelius

December 4, 20241 yr

Hello folks. I am thinking about getting a VIM3 or VIM4 as a PC for computation purposes. I think Monero mining shows the limit of a combination of memory + cpu. The higher the more performant the combination of memory + cpu is. My choice is currently between a board like VIM3 or VIM4 or a desktop i5 9th gen. I will be thankful if an owner can xmrig monero mining software to do a benchmark. So to do the benchmark one should: - Download xmrig - Run a benchmark and submit it: https://xmrig.com/docs/miner/benchmark The benchmark will be available in the benchmarks page in xmrig website. Note that there should be enough f…

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Farooq

October 4, 20233 yr

Hello, The mission: to change display resolution for "None-1" ('unknown display') - when no physical screen/display/monitor is attached. Machine: Banana Pi M5 (Bpi M5). I use it as a headless machine (without any monitor connected) and access it via a remote control/share screen application (such as: Teamviewer). The problem: the display is very small as the resolution is set to 720 X 576. I couldn't find any way or method to define/change the resolution in such a case. How can this be done? I'll appreciate any assistance you can provide. Thanks in advance! This is the information of the machine and Armbian version installed…

• 0

  Reputation Points

• 4 replies
• 10.5k views

SoSie

March 16, 20233 yr

Hello, I’m in a pickle. I bought an Odroid HC4 a few months ago, setup a RAID-1 array and installed Nextcloud on it. At the time, I used `nand-sata-install` to move the system from the SD‑card to a partition of one of the HDD (/dev/sda1), out of RAID (/dev/md0), and leave the bootloader on the SD-card. I did not make a backup of this SD-card and, after rebooting today, I realised the SD-card was not functioning any more. No device I use (Sansa audio player with Rockbox, phone with Ubuntu Touch, Laptop with Ubuntu) would even detect it. I was thinking of using `nand-sata-install` again to only update the bootload…

• 0

  Reputation Points

• 0 replies
• 2.6k views
• 1 follower

arkhi

March 18, 20233 yr

I tried 3 las disk images in SD card, update and OMV is not available fo install. In all tutorials show that OMV is available there. But when on my N2, it's not available.

• 1

  Reputation Points

• 1 reply
• 4.2k views
• 1 follower

NicoD

October 7, 20224 yr

Hello, is it possible to add support for TS050 original LCD touchscreen in Armbian? How I can check tochscreen, is there any CLI tools? Thank you in advance.

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Igor

May 13, 20233 yr

Hi everyone, I'm using Radxa Zero HW version 1.4, 4GB RAM with 64GB eMMC. I used long time armbian on SD card. I decided to install MMC for better performance but armbian crashes APT involving stuffs. By the way, I'm using Rzero with headless and connecting via SSH from Win11 machine. I installed with producer tools directly writing image to MMC and alternatively installed with armbian-config tool from SD card to MMC. In both way successfully boots and connects Wi-Fi. For better diagnostic, how can I get error dump? (I lost SSH connection when its crushed).

• 0

  Reputation Points

• 0 replies
• 2.3k views
• 1 follower

erturk47

February 11, 20233 yr

I have recently acquired a BPI-M2 Pro with what is supposed to be USB WiFi (Realtek RTL8821CU). I am running Armbian 22.08.7 Bullseye. armbian-config does not recognize any WiFi. The output from lsusb -t also does not show the presence of USB WiFi as expected. root@bananapi-m2p:~# lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 5000M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/2p, 480M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M Do I have a defective device, or is the WiFi not actually a USB module? Is there something else I need to …

• 1

  Reputation Points

• 8 replies
• 5.1k views
• 1 follower

RayKnight

November 19, 20223 yr

Hi all, I have been using armbian jammy on my potato without issues. But since the weekend it only boots to initramfs and says can't find mmcblk1p1 I put the sdcard a live gparted and partitions are and verified. In initramfs I can find in /dev the mmcblk0p1 but not the mmcblk1p1 Now how can I change the boot or the name of the device?

• 1

  Reputation Points

• 6 replies
• 6.5k views

Roberto Rodrigues

September 12, 20233 yr

Hello! I recently ran updates on the old M2S I won from here, and that appeared to break my OS, so I went back to try reinstall. And that's where I hit a snag. For some reason, after booting, the kernels refuse to see the partitions on the SD card. /dev/mmcblk0 exists, but none of the subpartitions, and so the boot process cannot find the partition it's supposed to boot from. Neither Armbian_25.5.1_Bananapim2s_trixie_current_6.12.32_minimal.img.xz nor Armbian_26.2.1_Bananapim2s_trixie_current_6.18.15_minimal.img.xz get me past this issue. I've tried changing the power supply, debug with LLMs, but nothing appears to b…

• 0

  Reputation Points

• 4 replies
• 1.2k views
• 1 follower

baryon

June 18Jun 18

Hello, I recently updated my N2 server from Bullseye to Bookworm. Reboot went fine. I then noticed I still had the old kernel from the linux-image-odroidn2 package (4.9.190-odroidn2), so I ran armbian-config, and told it to switch to linux-image-current-meson64. It installed packages for a bit, then rebooted on its own without asking. Since then, every boot is stuck with a U-boot logo at the top right of the screen. What I tried: Fixed a couple of issues in /boot (zImage was a symlinked to the old `vmlinuz-4.9.190-odroidn2` that no longer existed, I made it point to `vmlinuz-6.1.11-meson64` instead; `boot.ini` referred to `boot/dtb/a…

• 0

  Reputation Points

• 0 replies
• 2.7k views
• 1 follower

val

August 14, 20233 yr

no WiFi Adapter after fresh installation. usbcore.autosuspend=-1 fixes it: ___ _ _ _ ____ ____ / _ \ __| |_ __ ___ (_) __| | / ___|___ \ | | | |/ _` | '__/ _ \| |/ _` | | | __) | | |_| | (_| | | | (_) | | (_| | | |___ / __/ \___/ \__,_|_| \___/|_|\__,_| \____|_____| Welcome to Armbian 24.2.1 Bookworm with Linux 6.6.16-current-meson64 System load: 46% Up time: 0 min Memory usage: 7% of 1.82G IP: 192.168.25.252 CPU temp: 28°C Usage of /: 66% of 3.0G [ Menu-driven system configuration (beta): sudo apt update && sudo apt …

• 0

  Reputation Points

• 3 replies
• 5.8k views

blaubarschbube

February 8Feb 8

Hi, Odroid N2+ Armbian 22.05 Jammy Kernel 5.10.y, Size: 360Mb, Updated: Jul 1, 2022 + XFCE installed by means of armbian-config htop shows Systemd: degraded (1/372 failed) root@n2p-dev:~# systemctl --failed UNIT LOAD ACTIVE SUB DESCRIPTION ● fwupd-refresh.service loaded failed failed Refresh fwupd metadata and update motd LOAD = Reflects whether the unit definition was properly loaded. ACTIVE = The high-level unit activation state, i.e. generalization of SUB. SUB = The low-level unit activation state, values depend on unit type. 1 loaded units listed. root@n2p-d…

• 0

  Reputation Points

• 0 replies
• 3.9k views

vinser

August 4, 20224 yr

Every time i do umount of an nfs folder from a qnap nas i get an error in syslog similar to that attached, sometimes my board reboot after error I have Armbian 24.5.5 bookworm I need to mount using nfsv 4.0 or 3 because my nas doesnt support nfs 4.1 or newer. I use a command like this mount -t nfs -o nfsvers=4 -o minorversion=0 myqnapnas:/Backups /mnt I'm using official Armbian 24.5.5 bookworm image from armbian site on a khadas vim1s khadas_vim1s_error.txt

• 0

  Reputation Points

• 5 replies
• 3.3k views

Ivano Brunet

September 10, 20242 yr

Hi, after a long time I started up my C4 and tried both the standard download kernel as well as a home compiled one. I need SPI on the C4, so I changed the device tree to meson-sm1-odroid-c4-spidev.dtb, and see spidev kernel modul loaded, but no driver, and I don't get any signals on the corresponding pins. Any help is appreciated - would be great to have SPI working again... See you, Michael

• 0

  Reputation Points

• 4 replies
• 5.3k views

mboehmer

September 15, 20242 yr

Hi, in addition to this topic I would like to mention that the current Odroid N2 Firmware (Armbian 22.05.0-trunk.0004 Jammy with Linux 5.10.103-meson64 / U-Boot 2022.01-armbian (Mar 03 2022 - 19:25:51 +0000) odroid-n2/n2-plus) as well has difficulties with both the orange and the red coloured eMMC modules at this time. The orange coloured eMMC module is recognised but couldn't be activated ("unable to select a mode : -5"): Spoiler G12B:BL:6e7c85:7898ac;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0. bl2_stage1 bl2_stage_init 0x81 hw id: 0x0000 - pw…

• 1

  Reputation Points

• 22 replies
• 15.6k views
• 3 followers

einsteinx2

October 31, 20223 yr

Hi everyone, I'm trying to control an 5v PWM Fan using hardware PWM pins of Banana Pi M5. I'm not able to output any pwm signal on any pin. It looks like there is an pwm controller visible at `/proc/device-tree/soc/bus@ffd00000/pwm@19000`. File `/proc/device-tree/soc/bus@ffd00000/pwm@19000/status` has content `okay` and file `/proc/device-tree/soc/bus@ffd00000/pwm@19000/pinctrl-0` has content `&`. When i run script: echo 0 | tee /sys/class/pwm/pwmchip0/export echo 40000 | tee /sys/class/pwm/pwmchip0/pwm0/period echo 20000 | tee /sys/class/pwm/pwmchip0/pwm0/duty_cycle echo 1 | tee /sys/class/pwm/pwmchip0/pwm0/enable echo 1 | tee /sys/cl…

• 0

  Reputation Points

• 8 replies
• 3.4k views
• 1 follower

c0rnelius

August 3, 20251 yr

This post is not a criticism but I suppose that noobs with experience with linux since 2006 like myself might get caught out by: * Desktops are very simple and minimal but containing standard features such as Chromium, Firefox browser, Office tools etc. This Ubuntu based "noble" distro DOES NOT have any browser installed as part of the image. Since I rarely use snaps, as they are controversial, I did not understand at first that "synaptic" will not install Firefox or Chromium. In fact you have to use the CLI terminal to manually install Firefox or Chromium with the "snap" program. May I suggest that the webpage description be amended to:…

• 0

  Reputation Points

• 1 reply
• 1.9k views

usual user

December 20, 2025Dec 20

I am currently using a completely outdated system on my Odroid-C1, specifically Ubuntu 16.04.7 LTS and I am able to transmit signals without issues using lirc 0.9.0. Without making any special changes to the /etc/lirc/hardware.conf file and using the following configuration: #Chosen Remote Control REMOTE="None" REMOTE_MODULES="" REMOTE_DRIVER="" REMOTE_DEVICE="" REMOTE_SOCKET="" REMOTE_LIRCD_CONF="" REMOTE_LIRCD_ARGS="" #Chosen IR Transmitter TRANSMITTER="odroid blaster" TRANSMITTER_MODULES="lirc_odroid lirc_dev" TRANSMITTER_DRIVER="" TRANSMITTER_DEVICE="/dev/lirc0" TRANSMITTER_SOCKET="" TRANSMITTER_LIRCD_CONF="" TRANSMITTER_L…

• 0

  Reputation Points

• 2 replies
• 541 views

Juhn_hoo

September 28Sep 28

I downloaded the most recent armbian focal for odroidc2. uname -a Linux odroidc2 5.6.18-meson64 #20.05.4 SMP PREEMPT Mon Jun 15 01:50:20 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux However, linux headers are not available for this version: apt-cache search linux-headers-current | grep meson64 linux-headers-current-meson64 - Linux kernel headers for 5.6.15-meson64 on arm64 Also here, only 5.6.15 available: https://apt.armbian.com/pool/main/l/ I tried to simply use 5.6.15 headers by manually setting the following link: lrwxrwxrwx 1 root root 37 Jul 4 21:00 /lib/modules/5.6.18-meson64/build -> /usr/src/linux-header…

• 0

  Reputation Points

• 4 replies
• 4.3k views
• 1 follower

Igor

July 6, 20206 yr

Is there a way to force a composite output? I was able to get composite video in LibreELEC but I would rather use Armbian if possible. Any information would be helpful.

• 0

  Reputation Points

• 0 replies
• 2.3k views

Hiroshima

August 15, 20233 yr

Odroid N2+ booting from eMMC with a 4TB USB drive. With the USB drive disconnected, the system boots fine and very quickly. With the USB drive connected, it throws hundreds of errors for about 30 seconds before finally moving on and booting from the eMMC. I have no desire to ever boot from SD or USB, so I would like to just disable those options. I found this topic https://forum.armbian.com/topic/10349-disable-u-boot-usb-support/ but I can't really follow what they're talking about and I have no idea how to patch U-boot or build a new boot image. Is there an easier way to do this? Here's what the errors look like: Hit any key to stop autoboot: …

• 1

  Reputation Points

• 7 replies
• 4.9k views
• 1 follower

c0rnelius

February 2, 20251 yr

In my quest to use an ODROID N2 as a time server, I had to figure out how to enable UART_EE_A. Device trees for other boards sometimes enable UART A in the base device tree but the ODROID N2/N2+ does not. I am not sure why device trees don't fully define devices like UART_A and then just leave them disabled instead of partially defining them with missing "pinctrl" entries (as in the N2 device tree). Anyway, I've attached `meson-g12b-odroid-uart-ee-a.dtso` as an example of how to enable UART_EE_A. Additionally: The DT overlays for Meson UARTs (e.g. `/boot/dtb/amlogic/overlay/meson-uartA.dtbo`) are not compatible with …

• 0

  Reputation Points

• 4 replies
• 4.5k views
• 1 follower

bo911

January 19Jan 19

I want to use a StromPi3 board with my lepotato board. I am using the armbian image. I used armbian-config to enable the serial ports and both show up as /dev/TTYAML0 and /dev/ttyAML6. Nonetheless I am unable to communicate on the serial ports even when connecting jumpers and a USB serial converter. I later tried to modify the divorce tree by hand. No change. Is there something else I could try to get the serial port on pins 8 and 10 working?

• 0

  Reputation Points

• 0 replies
• 2.2k views

NeoCortex97

March 19, 20233 yr

Hi Everyone, on my odroid n2+ _armbian 5.10.123-22.05.3 everything is fine but the system runs on a class 10 (uhs-i) sd card with very low speed... odroidn2:brontolo:# sudo hdparm -Tt /dev/mmcblk0p1 /dev/mmcblk0p1: Timing cached reads: 3440 MB in 2.00 seconds = 1720.27 MB/sec Timing buffered disk reads: 68 MB in 3.05 seconds = 22.28 MB/sec ...performance is better with an emmc card but my interest is if you can make settings to improve the access speed, I haven't found anything on the net..!! would that be too complicated !? 😁 thanks for the advices... greetings to all..

• 0

  Reputation Points

• 0 replies
• 2.4k views
• 1 follower

Alessandro Diocleziano

May 3, 20233 yr

I've just install Armbian_23.02.2_Odroidhc4_jammy_current_6.1.11.img to my new odroid hc4 but after copy sd to sata by using nand-sata-install the system stuck dureing boot on an "emergency mode error".

• 0

  Reputation Points

• 1 reply
• 3.4k views

abreyu

June 5, 20233 yr

I am unable to configure Xorg to ignore (and stop using as its default) the None-1 video device causing me not to be able to display a desktop via the HMDI-1-1 device. It has been suggested (https://ubuntu-mate.community/t/how-to-configure-xorg/26732/3) that I disable this device in the kernel, hopefully, via a kernel option such as : video=None-1:d Does anyone know where (which file) and how (specific method) I should do this?

• 0

  Reputation Points

• 3 replies
• 4.7k views

Walter Zambotti

July 11, 20233 yr

After updating my Odroid N2+ today, lo is the only network interface shown when running 'ip a' The update was 18 packages: root@odroidn2p10:~# apt upgrade Reading package lists... Done Building dependency tree... Done Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: armbian-config armbian-firmware armbian-zsh libldap-2.5-0 libldap-common libnss-myhostname libpam-systemd libsystemd0 libudev1 linux-dtb-current-meson64 linux-image-current-meson64 linux-u-boot-odroidn2-current python3-tz sudo systemd systemd-sysv tzdata udev 18 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to g…

• 0

  Reputation Points

• 3 replies
• 4.4k views
• 1 follower

MarkP

April 15, 20233 yr

hello, My image is (Armbian BookwormXFCE desktop 20230831) and download to cm4 moudule. When I using the Bananapi CM4 base board ( https://wiki.banana-pi.org/File:BananaPi_BPI-CM4_base_board_1.jpg) the USB function is working. But I using the common RPI CM4 base board, such as waveshare's cm4 nano-b (https://www.waveshare.net/wiki/CM4-NANO-B) the USB function is not working. I compare the difference of two board's schematics. Bananapi's base board is connecting the fs1.1 usb hub ic. but waveshare's base board was connecting USB D+/D- to USB host directly . I also tried bananapi official image (both Debian and Ubuntu mate) and…

• 1

  Reputation Points

• 3 replies
• 3k views
• 1 follower

陳柏儒

October 12, 20233 yr

USB gadget mode does currently not work OOTB on Armbian, but it can be enabled easily with a device tree change or overlay: /dts-v1/; /plugin/; / { compatible = "radxa,zero", "amlogic,g12a"; fragment@0 { target = <&usb>; __overlay__ { dr_mode = "otg"; }; }; }; I can open a PR for adding this as device tree overlay, or enabling OTG OOTB on Radxa Zero, like vendor did: https://github.com/radxa/kernel/commit/775a467 The latter would be simple. In case of an overlay, I'd need some hint about how to do it best: Adding it to the general meson64 overlays patch seems to be right: https://github.com/armbian/build/blob/master/p…

• 0

  Reputation Points

• 0 replies
• 3.6k views
• 1 follower

MichaIng

December 3, 20223 yr

With the most recent minimal Debian image, Armbian_26.2.1_Bananapim2s_trixie_current_6.18.15_minimal.img on my A311D, I hit a problem with Xorg. Instead of starting up into dwm via lightdm's autologin, all I got was the blank blinking cursor screen. Working through it with an LLM, the resolution worked out to be adding a stanza to Xorg.conf. Section "ServerFlags" Option "AutoAddGPU" "false" EndSection Is this the correct solution? Is this known or understood? I know nothing about any of this. I presume it's related to how the devices look to Xorg via the kernel, but I have no understanding beyond that level, if that's even correct.

• 0

  Reputation Points

• 0 replies
• 662 views
• 1 follower

baryon

June 19Jun 19

Hi, I fixed the following issue for my own system for now, but wanted to let you know: After upgrading the LaFrite from Armbian Buster 20.08 to 20.11 using "apt upgrade" it didn't boot anymore. It showed a message "Ramdisk image is corrupt or invalid", so I checked /boot/uInitrd and it linked to uInitrd-5.9.6-meson64, which didn't exist. I fixed it by downloading the latest image and replacing everything in /boot except armbianEnv.txt with what was inside the image. Afterwards it booted again. I replaced everything, because the image apperently still is on linux 5.9.6, while vmlinuz and other files on my system showed 5.9.10. …

• 1

  Reputation Points

• 4 replies
• 7.1k views
• 2 followers

thorle

December 13, 20205 yr

Hello I've tried to install the newest Armbian image "Armbian_22.08.7_Bananapim5_jammy_edge_5.19.16_cinnamon_desktop.img.xz" Copied with Balena Etcher to SDcard. Attached a serial tty cable and started with card in SD-Slot. Unfortunately it stops while booting. Please can anybody help me ? Here is the serial log:

• 0

  Reputation Points

• 1 reply
• 4.6k views

Schaagi

November 13, 20223 yr

Hi all. A few improvements have been made lately for the Odroid N2/N2+. HDMI sound for example. There are just a few little things I'd like to see happen to make it even better/perfect for desktop use, and for gaming when the GPU drivers for it are ready. Make HDMI resolution selectable in Armbian itself instead of in boot.ini. This would fix multiple issues. Like with mainline it always defaults to 4K on my 4K display whatever resolution I set in config.ini. The N2+ can work well at 1440p, but 4K is just too much for it. In legacy 1440p works when setting it in boot.ini. But can't be changed in Armbian itself. For gaming this will be a huge problem(on mai…

• 1

  Reputation Points

• 10 replies
• 7.4k views
• 2 followers

rob2021

January 8, 20215 yr

Hello there, I'm trying to get an i2c ssd1306 screen to work with my Radxa Zero, without much luck for the time being. https://paste.armbian.com/cirulemeho I found two i2c devices, 3 and 5. sudo i2cdetect -y -r 3 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- UU -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- …

• 1

  Reputation Points

• 2 replies
• 3.8k views
• 1 follower

gounthar

January 29, 20242 yr

Hi, i have armbian bullseye (headless) installed on my odroid-hc4. petitboot is disabled. The boot-partition lies on a sd-card while the root-partion is on a ssd. this configuration worked fine. After upgrading to armbian bullseye 22.11 the boot process stucks in initramfs cause the root file-system is not found anymore (ALERT! UUID=xxx does not exist. Dropping to a shell. The sd-card with the boot partition as well as the ssd with the root-partition can be mounted on another PC and seem to be flawless. the UUID shown in fstab and initramfs are identical. In initramfs ls /dev/sd* shows no devices while ls /dev/mm* shows the sdcard (mmcblk01...). I don't really …

• 0

  Reputation Points

• 7 replies
• 6.5k views

charly_53

December 9, 20223 yr

Colleagues, please help me because I don't know what this error is. I wanted to install some minimal version of Armbian to install OpenMediaVault on my Odroid C2 and every time I see such an error, before I do anything I boot the system to a freshly installed one...

• 1

  Reputation Points

• 4 replies
• 2.9k views

CryBaby

November 2, 20241 yr

Using the Armbian_24.11.1_Sweet-potato_bookworm_current_6.6.62_xfce_desktop.img I get the above error in /var/log/Xorg.0.log and no X server due to a missing drop-in file. The file is attached and should be dropped into /etc/X11/xorg.conf.d/ 10-meson.conf

• 0

  Reputation Points

• 2 replies
• 2.4k views

TonyMac32

January 7, 20251 yr

Installing Bullseye from download list works fine, but after `apt update / apt upgrade` or a firmware update through armbian-config, boot process gets stuck with Uboot logo in the corner and won't proceed any further. Any ideas? Using a EMMC card and BalenaEtcher to burn.

• 0

  Reputation Points

• 4 replies
• 4.1k views
• 2 followers

sportyspice

December 2, 20232 yr

I was curious if anyone had worked on power management for the S905X. My Le Potato was idling around 0.32A@5.1V = ~1.5W The LibreElec guys documented idle current ~2/3 of that here so I was curious what was going on. Of course I am running a 4.18 armbian kernel (I assume they were using a 3.14 kernel for their tests) so I was never going to match their numbers precisely, but 33% more power seemed like an awful lot. Then I realized I had a USB thumb-drive installed, so I did some experimentation... My numbers were generated using an inline USB power meter that measures pretty accurately compared to a bench meter. My initial findings: …

• 1

  Reputation Points

• 8 replies
• 9.8k views
• 1 follower

Da Xue

October 1, 20188 yr

Hi, everyone, Recently, i found i can't change ssh port on 6.4.16 bookworm (Onecloud) cli version(https://github.com/armbian-delta/os/releases/download/23.8.0-trunk.2/Armbian_23.8.0-trunk.2_Onecloud_bookworm_edge_6.4.16.img.xz#onecloud) i changed the `/etc/ssh/sshd_config` add the `Port 10086` .and then i restart the system, It still not working, ssh port only work on `22` but at the same time, i found the other thing `KexAlgorithms curve25519-sha256@libssh.org,ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group14-sha1,diffie-hellman-group-exchange-sha1,diff…

• 0

  Reputation Points

• 13 replies
• 11.3k views
• 2 followers

Ephraim Gariguez

July 2, 20242 yr

with ccrypt and cryptsetup installed creation of a luks fs fails. Even gparted shows this in file system support window. OS Version: Linux w1 5.6.18-meson64 #20.05.4 SMP PREEMPT Mon Jun 15 01:50:20 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux

• 0

  Reputation Points

• 0 replies
• 2.6k views
• 1 follower

seafrog

July 8, 20206 yr

bringing up a BIG 3d printer from square one on a bpi--m5 with a fairly new image. The pager requires 10 or more mouse clicks, starting with the _ . . . . . at the upper left corner of what I think is the default xfce4 screen. All the eye candy and mouse clicks to actually switch workspaces are very distracting when one is trying to configure klipper. Can all this be reduced to a single click on the dot representing that workspace in the micro-pager? The eye candy is impressive to visiting frogs, until its a PITA when actually doing work. We buy these things in 6 pack qty's to do work, and give you a small monthly support, but impressing the frog…

• 0

  Reputation Points

• 0 replies
• 1.5k views
• 1 follower

gene1934

December 21, 2025Dec 21