Rockchip
Quick links to search tags:
Banana Pi M7, BIGTREETECH CB2, Khadas EDGE2, Libre Renegade, NanoPC T6 LTS, NanoPi M5, NanoPi M6, NanoPi R3S LTS, NanoPi R4S, NanoPi R6S, NanoPi R6C, NanoPi R76S, Odroid M1, Orange Pi 4 LTS, Orange Pi 5, Orange Pi 5 Plus, Pinebook Pro, ROCK 5A, ROCK 5B, ROCK 5C, ROCK 5 ITX, ROCK PI E, ROCK PI S, ROCK S0, Zero 3W/3E, RockPRO64, Tinkerboard
-
Hello, i'm using Armbian 23.11 Jammy-amazingfated Gnome. Kernel 5.10 If to seek a couple of times in h264 1080p BD remux'es it will cause system restart. Any video players are affected. Tried mpv, vlc, kodi and others. Problem affect just h264 1080p remuxes, that typically are 30..40 Gb, smaller h264 or even larger h265 files seem to work fine. I tried fresh install of armbian, where no rkmpp is installed, then h264 files plays/seeks fine, in software mode of course. Once I did sudo update/upgrade, that also installs rkmpp and other rockchip stuff, then videos start to play with rkmpp and problem is back. I've tried disabling hw deco…
-
I just installed with the latest KDE image, but I'm able to reproduce this with any of the images available. After going through the initial configuration, wifi works great. I updated apt and upgraded everything. Then I installed the armbian-firmware-full package. After rebooting wifi still works. Then I setup Bluetooth for my mouse and keyboard. They work correctly. After rebooting I no longer see any networks to connect to for wifi. If I disable Bluetooth and reboot wifi works again and so does Bluetooth. Is this an issue of daemons or drivers loading in the wrong order?
-
Reputation Points
- 0 replies
- 1.2k views
- 1 follower
-
-
Hi, I have a MIPI screen to replace. I have configured DTS in the kernel, but it doesn't light up and the backlight doesn't respond. May I ask： Uboot needs to initialize and light up the screen, but there is no screen configuration in the built-in DTS of Uboot. How can I adjust the screen related configuration in DTS?？ help help.....
-
armbianmonitor -u https://paste.next.armbian.com/hoyonuruye I installed the newest fresh debian minimal image for the RockPi-S and no matter what I do overlays do not apply. I've followed and compiled spi1 and spi2 rk3308. I've also tested the external antenna device tree as I have installed an external antenna: However neither the external antenna is being used nor spidev are present. I have diffed dtc -I fs -O dts /proc/device-tree and they are identical before and after enabling the overlays in armbian-config and rebooting. I was able to confirm the "overlays" work by manually copypasting their changes in …
-
Reputation Points
- 42 replies
- 29.4k views
- 4 followers
-
-
Can anyone point me in the right direction for an Armbian image that would allow audio recording over the 3.5mm jack? I'm trying to record audio over the 3.5mm jack. This works on a previous installation, but I'm trying to update to a curreent Armbian. Running Tinkerboard S R2.0 and this image: Armbian_25.2.1_Tinkerboard_noble_current_6.12.13_xfce_desktop.img Playback works record does not. Works: aplay /usr/share/sounds/alsa/Side_Right.wav -D hw:CARD=Audio,DEV=2 None of the following arecord commands work: arecord --vumeter=mono -D hw:CARD=Audio,DEV=0 -f S16_LE -c 2 -d 5 /tmp/t.wav arecord --vumeter=mono -D hw:CARD=Audio,DEV=1 …
-
Reputation Points
- 3 replies
- 3.2k views
- 1 follower
-
-
Hi, I'm using orange pi 5, and I noticed that I'm using 100Mb/s instead 1000Mb/s, i changed the cables that are working in another pc to a 1000Mb/s but still works to 100Mb/s, I changed to another kernel like 6.12.32-current-rockchip64 with no luck, any idea how to solve it? root@opi5 /home/pi# ethtool end0 Settings for end0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Full 100baseT/Full 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Full 100baseT/Full …
-
Reputation Points
- 11 replies
- 5.7k views
- 2 followers
-
-
What? Sharing various gaming experiences with RK3588 (Orange Pi 5) on Armbian. Why? Because RK3588 is a capable gaming chipset, Armbian is a good OS; Vulkan on RK3588 is getting better over time (PanVk) How? Posting your gaming results here (preferably with setup and screenshots/videos) so people can learn more.
-
Reputation Points
- 197 replies
- 79.6k views
- 4 followers
-
-
Hi all, looking for a bit of advise. I had an idea recently in that I have a problem of syncing a 20Tb USB 3.0 RAID0 drive with a 20Tb NAS. I have two fully duplicated RAID0 drives with no protection, so whenever I upgrade the capacity of a drive, I do a full sync. I do this maybe once a year. Whenever I have to do a full sync however it usually ties my MacBook up for a few weeks to transfer that much data over, so I had the idea recently of having a maker board do it since Linux/Armbian supports HFS+, I can just do an rsync between the two. I opted to purchase a Tinkerboard for the GigE Ethernet (I'll live with the USB 2.0), installed, up and running all…
-
Is there a way to upgrade from an earlier version to 5.41?
-
Reputation Points
- 8 replies
- 4.8k views
-
-
Using 5.41 I ran armbian-config to install armbian on a tinker board s emmc. Install went ok but get nothing but a black screen on boot. Any ideas on what to do to get it going?
-
Reputation Points
- 22 replies
- 9.2k views
- 1 follower
-
-
hello guys, i recently observed a weird behavior with my nanopi R4s(jammy os). when the power goes OFF then ON in like 5 seconds duration then the nanopi does not boot up at all! i need to remove the adapter for like 15 seconds so it would be able to boot again! is this normal?
-
I know this driver should be part of the recent kernel releases (and definitely avail for 5.10) but I am not sure how/why/where this driver would be in the armbian release. I also did install the firmware files but I don't see the module in the /usr/lib/module section. Any suggestions to build or enable this driver? Thanks
-
Reputation Points
- 11 replies
- 7.8k views
- 1 follower
-
-
Processing triggers for initramfs-tools (0.140ubuntu13.1) ... ln: failed to create hard link '/boot/initrd.img-5.10.110-rockchip-rk3588.dpkg-bak' => '/boot/initrd.img-5.10.110-rockchip-rk3588': Operation not permitted update-initramfs: Generating /boot/initrd.img-5.10.110-rockchip-rk3588 update-initramfs: Converting to u-boot format I am getting this error every time I do an apt upgarde. I am running on a 256Gb NVME drive and booting off of it with no problems. So does this error mean it's not actually updating /boot/initrd.img-5.10.110-rockchip-rk3588 ? The third line there makes me think that it just fails with the hard link and then generates the…
-
Reputation Points
- 2 replies
- 6.7k views
- 1 follower
-
-
$ neofetch ubuntu@orangepi5 ---------------- █ █ █ █ █ █ █ █ █ █ █ OS: Armbian (23.11.0-trunk.145) aarch64 ███████████████████████ Host: Orange Pi 5 ▄▄██ ██▄▄ Kernel: 6.6.0-rc1-edge-rockchip-rk3588 ▄▄██ ███████████ ██▄▄ Uptime: 4 mins ▄▄██ ██ ██ ██▄▄ Packages: 427 (dpkg) ▄▄██ ██ ██ ██▄▄ Shell: bash 5.2.15 ▄▄██ ██ ██ ██▄▄ Terminal: /dev/pts/0 ▄▄██ █████████████ ██▄▄ CPU: (8) @ 1.800GHz ▄▄██ ██ ██ ██▄▄ Memory: 196MiB / 15718MiB ▄▄██ ██ ██ ██▄▄ ▄▄██ …
-
Hi, I'm pretty new to this forum may be I will ask some already answered questions, but here they are: I just had a new orangepi 5 plus card and I failed to use the "buses": - I2s: didn't find anywhere how to activate it (i'm trying a dac as a soundcard). Didn't find the hifiberry-dac overlay neither (ok maybe this one is just for raspberry). - spi: I plugged a simple mcp3008 to the spi pins but can't read anything on it (i have the /dev/spidev0.0/1 and /dev/spiddev4.0/1 devices). I think I respected the rights pins. - i2c: when I activate the overlays in armbianEnv.txt, I can see a lot of messages every seconds with dmesg about rk-hdmi. Ma…
-
Hi Team, I want to build or get pre-built armbian image for kernel 4.4 with wifi : rtl8723as enabled. Please help or provide any suggestion to build armbian image for rockpi-e. Any help or suggestion will be appriciated.
-
Reputation Points
- 3 replies
- 3.1k views
- 1 follower
-
-
I just installed with the latest KDE image, but I'm able to reproduce this with any of the images available. After going through the initial configuration, wifi works great. I updated apt and upgraded everything. Then I installed the armbian-firmware-full package. After rebooting wifi still works. Then I setup Bluetooth for my mouse and keyboard. They work correctly. After rebooting I no longer see any networks to connect to for wifi. If I disable Bluetooth and reboot wifi works again and so does Bluetooth. Is this an issue of daemons or drivers loading in the wrong order?
-
Reputation Points
- 0 replies
- 1.6k views
- 1 follower
-
-
My goal is to get OMV5 running on my RockPro64 (previously running OMV4 on an Ayufan image). I'm using this guide here from over on the OMV forum which suggests that Buster Server is the only thing that will work; this is based on the 4.4 kernel, and the suggested alternate of Buster Minimal is not present. I've tried downloaded from multiple locations and cannot get the SHA to match. The 256 per Checksum utility is 760BD8FA51316D07E875D5B8687E837C8C00070E68F44B8B413C76EC217C606B while the file from the Armbian download site is 3ddc7bc3e47bc39a9a9bed6109d35ca712bd34a6206121d37814ca8faf4b8798 If i try to flash the image to SD and boot device fails …
-
I was able to flash armbian bookworm cli to the ssd using balena etcher but when I boot the OPI5 from the sdcard and run lsbk it can only see the sdcard any ideas ...
-
What is the current status of Pinebook Pro? I see there were Pinebook-Pro-specific install images for older version of Armbian, but there doesn't appear to be any for more recent versions, and currently, the download page points to (non-machine-specific?) UEFI install images. Is this a transition that was discussed/announced, and can I read the discussion/announcement in archives somewhere? Also, does anyone have any installation/testing reports? Is 25.02 known to work on the Pinebook Pro? I've tried a few different times to create a Armbian SDCard for my Pinebook Pro. I've only had one success, one one of my early attempts. Unfortu…
-
Reputation Points
- 3 replies
- 3.9k views
- 1 follower
-
-
Hi I managed to fix an issue with the usb-c port of the orange pi 5 plus. It seems the device is not activated unless you put it in host mode yourself: as user root: echo host >/sys/kernel/debug/usb/fc000000.usb/mode I have tried a usb-c network card and usb stick. Both work after this command! I noticed this when I installed the 6.1.115-vendor-rk35xx kernel. This one does not need this setting, it switches automatically from device mode to host and vice versa. I had alot of problems with analog sound on older kernels, e.g. youtube just hangs unless you mute the sound. But sound in noble 6.19.0-edge-rockchip64 wo…
-
Reputation Points
- 3 replies
- 1.5k views
- 1 follower
-
-
I confess, I have no idea what to do with the contents of this repository. Any help would be great, as I've said before, my Linux experience is lacking on things, the work I do is usually in hardware with kiB of RAM... I'm working on the assumption that this would be the best lib to install, if I'm wrong, let me know. https://github.com/rockchip-linux/libmali
-
Anyone having luck getting firefox quantum to run? I added the ppa and installed it but it crashes immediately.
-
Good Morning, I'm using Libre renegade with armbian bullseye minimal. How can I change splash screen, replacing the armbian logo and 4 penguins, with a personal one? Has anybody done it eralier? Thanks in advance
-
Hello all, Is there any chance to run mainline kernel? Support for rk3588 seems to be starting with 6.2 and 6.3 (mainline has dts for rock 5b).
-
Reputation Points
- 8 replies
- 8.8k views
- 4 followers
-
-
Someone asked in a different thread how I got Dolphin to run so thought I'd start a thread so not to pollute the other one. Basically it wasn't that hard especially if youve done some git'hubbing before. I think I followed the 'Ubuntu' instructions here. Make sure you get the dependencies and do all the steps correctly. It should build without problems if you do. (remember you have a lot of cores on Opi5 so can use 'make -j6' or even higher) https://github.com/dolphin-emu/dolphin/wiki/Building-for-Linux You then want to set a config flag to make Dolphin use GLES instead of big brother OpenGL. (you probably wa…
-
Hello Armbian-Community! TL;DR I've successfully enabled the Rockchip RK3568 NPU (0.8 TOPS INT8) on the ODROID-M1 with 8GB RAM running Armbian 6.18.9-current-rockchip64. The only thing needed to make this work for everyone is a 1-line kernel patch in Armbian build that I've already submitted: https://github.com/armbian/build/pull/9403 Once this patch is merged into Armbian, the DKMS modules will work out-of-the-box on all RK3568 boards. The Problem 1. Hardkernel and Rockchip provide NPU patches for quite old kernel versions: rockchip <= 6.6 hardkernel <= 5.10 2. IOMMU …
-
Anything targeting the mainline will be getting 4.12 tonight, I can confirm some patch failures for Tinker Board/MiQi NEXT, Specifically: 0002-Adaptation-ARM-dts-rockchip-fix-the-MiQi-board-s-LED Was patched in the kernel. 9002_dts_rk3288_updates - Fixed and the packaging postinstall-scripts patch specific chunk: scripts/package/builddeb There is no "Provides:" statement.
-
Hi, I've downloaded Ubuntu-mainline image at https://www.armbian.com/tinkerboard/ and written to SD as below but Hang while booting. # dd if=Armbian_5.35_Tinkerboard_Ubuntu_xenial_next_4.13.16_desktop.img of=/dev/mmcblk0 5742592+0 records in 5742592+0 records out 2940207104 bytes (2.9 GB, 2.7 GiB) copied, 481.509 s, 6.1 MB/s Log: U-Boot SPL 2017.09-armbian (Nov 22 2017 - 17:12:11) Returning to boot ROM... U-Boot 2017.09-armbian (Nov 22 2017 - 17:12:11 +0100) Model: Tinker-RK3288 DRAM: 2 GiB MMC: dwmmc@ff0c0000: 1 *** Warning - bad CRC, using default environment In: serial Out: serial …
-
Reputation Points
- 7 replies
- 6.6k views
- 1 follower
-
-
Hi all, Saw that via Slashdot. A RPI 3 b+ benchmark comparing against other SBCs and TinkerBoard. Check it out: https://www.phoronix.com/scan.php?page=article&item=raspberrypi-3-bplus Feeling great for buying one, after reading all 18 pages of the forum! Ah. A big shout THANK YOU to Igor, Tony, Kaiser and everyone else that helped build a working Armbian release to this SBC. -RF
-
Reputation Points
- 6 replies
- 3.8k views
- 2 followers
-
-
Hi guys, sorry, on with my second issue with the Asus Tinker Board and installing a DS3231 Real Time Clock module. I've tried following any instructions on the internet for Tinker Board use and a couple for the Raspberry Pi, from recompiling the kernel through to trying to edit boot files. I just cannot get this thing working so I've now got myself a fresh install of Armbian Stretch 4.14 and ready to go again. Can anybody provide a step-by-step installation for the Tinker Board and this module (I've been told the DS1307 is the same kernel module but for the life of me I cannot find any modules/.ko's available in Armbian)? Ma…
-
Reputation Points
- 10 replies
- 15.4k views
- 1 follower
-
-
If anyone has troubles with HDMI when using 5.x kernels, and has enough skills to recompile an armbian, give this a try : https://github.com/Miouyouyou/build And then either answer here, or in the bug report : https://github.com/armbian/build/pull/1887
-
I just download Armbian_20.11.6_Tinkerboard_bionic_legacy_4.4.213_desktop.img.xz flased it on sd card with balenaEtcher, tried to boot and got error: So. I can't do my first login.
-
FYI. Searching some forums around the web, stumbled on a post that indicated the TU3 Nano would work on the OPi 5. I thought I would give it a try. It worked for me plugged it in reboot. Download speed topped out at 200mb on the usb3 (top plug) connected to 5Ghz wifi. Happy days. Running the Feb.27 stable version of Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110_gnome_desktop. TC
-
Reputation Points
- 4 replies
- 3.8k views
- 2 followers
-
-
I tried both the 6.8.10 and 6.1.43 releases from CI pipeline and none of these has the ap6275p wifi option in the armbian-config tool. There was a previous post that mentioned that the module got merged for the new kernels but is there an ETA to have this one in the CI releases? I'm curious to try vlc but haven't been able to install that one yet with the new releases.
-
Reputation Points
- 3 replies
- 3.1k views
- 2 followers
-
-
I know this sounds strange, but I cannot get any of the images to boot. I have an R3S non-LTS + SD card. It works well with the stock images from FriendlyElec, but none of the Armbian images I tried will boot. I tried different tools to write the SD (BalenaEtcher, USBImager, Rufus), but nothing changed. When I tried to read the SD card with Armbian on my x86 laptop running Debian, the system didn’t recognize any proper partitions (maybe that’s normal, maybe not—I don’t know). But when I write an Armbian image for Allwinner NanoPi, the partitions are detected correctly. And finally, I can’t connect to the debug UART, so I can’t get any logs. I feel…
-
Reputation Points
- 13 replies
- 6.8k views
- 2 followers
-
-
Does anyone have any clues to give as to setting up dual screen on the Nanopi m6? I searched the forum and found nothing. I don't know why I can never easily find Anything here. The forum shows one post for the Nanopi m6 and I know that can't be right. The Nanopi mirrors by default, and that is just not going cut it. Currently installing X on a minimal install. But that's the next thing. Get a reasonablf sized terminal up.
-
Reputation Points
- 6 replies
- 2.7k views
- 1 follower
-
-
Due to the shortage of memory chips these days, Radxa is using different emmc models in their boards. For example, I recently ordered a big batch of Rock S0 boards, but they had to be delivered with Sandisk iNAND 32GB emmc drives instead of the typical 8GB option. The problem is that Armbian did not reliably boot on these new boards. It randomly gets stuck during initialization with the onboard LED endlessly blinking. Some boards works, some did not, some only works sometimes. Long story short, in case other people also have this problem: I found the solution. I believe it is caused by Armbian's Rock S0 device tree enabling the HS200 high speed mode for t…
-
Hi guys I have experienced a lot of system instability with the rockpro64 on debian and armbian as explained here: https://forum.pine64.org/showthread.php?tid=17083 and here: https://github.com/monero-project/monero/issues/8473 I think the solution lies in what the guys are discussing here: https://forum.pine64.org/showthread.php?tid=7387 Can someone please give me a clear set of instructions on how to create an image to boot with with lowered ddr clock frequency? Presumably from the files listed here?: https://github.com/rockchip-linux/rkbin/tree/master/bin/rk33 i.e.: files such as rk3399pro_ddr_…
-
Reputation Points
- 1 reply
- 3k views
- 1 follower
-
-
I am waiting on my opi5 but was already investigating how to run Roblox (an x86 32 bit Windows game) on it. Grapejuice + box86 + wine could do the trick and saw this interesting script: https://github.com/NicoD-SBC/armbian-gaming Will this be working for opi5 too or is it specific to rk3399 (saw that in some compiler flags)? Anybody experience or an updated installer script? Related info: This YouTube channel covers examples of running games on rk3588 (rock5b) making me believe performance could be quite good: https://youtube.com/@TheByteman
-
I lost whole day yesterday to try boot with new images from Armbian download page - kernel 6.1 / kernel 6.8 bookworm/trixi and none boots... If I take Ubuntu or Debian image I have no problem to boot from. Do you have the same?
-
What is the process to get python3 talking to the GPIO pins? I have installed the ASUS-GPIO package but it is not working. Under the tinker debian release, this h/w was working correctly, so I know this is some kind of s/w issue. Thanks!
-
Reputation Points
- 54 replies
- 29.7k views
- 2 followers
-
-
Hey everyone I've compiled my own kernel using this awesome tool, and I'm now running it on a tinker board. Everything's been working fine, except for one annoying thing I just ran into: I can't use the GPIO pins. When I try to use a pin in python I just get this message back: "RuntimeError: This gpio is set to other function!". If I run Debian I can use the gpio just fine, but I need some kernel modules that doesn't ship with Debian. That's why I've compiled my own armbian kernel. Anyways, any idea on how to fix this? Any special module I should add when compiling the kernel? Thanks Marius
-
Reputation Points
- 0 replies
- 2.8k views
-
-
using latest Armbian: Linux indi 4.4.156-rockchip64 #21 SMP Wed Sep 19 13:14:57 CEST 2018 aarch64 aarch64 aarch64 GNU/Linux I can do the following (as sudo su), but, no voltage on the specified pin (pin 5, Linux pin 4): echo -n "4" > /sys/class/gpio/export echo -n "out" > /sys/class/gpio/gpio4/direction echo -n 1 > /sys/class/gpio/gpio4/value echo -n 0 > /sys/class/gpio/gpio4/value echo -n "4" > /sys/class/gpio/unexport I get no light on my generic LED with a 100k resistor - which lights when I move from pin 5 (Linux pin 4) MicroSD end of the board -> [ . . ] [ . . ] [ . . ] <…
-
I've been (trying) to move the Tinker and MiQi u-boots to 2020.07, however if I use any of the following: A MiQi, A Tinker S an image for a Tinker S an image for a Tinker on a Tinker S I get stuck in the initramfs busybox with it telling me the filesystem is toast. The only 2020.07 combo I've gotten to boot is the Tinker with the non-eMMC supporting u-boot. As for clues, I haven't found any, the u-boot source code is of course very well organized for debugging purposes :lol:. If anyone has an idea about what could be going on with this let me know, I'm shelving the effort to think about other stuff.
-
I've setup the pwm overlay but while it shows up the pwm devices in /devices - it is missing the pwm0 control I've read couple posts where ppl have been able to override the overlays by decompiling the original one, but I can't make sense of the dtc dtb dtbo and dtsi files 😕 Any guides or other suggestions to fix the pwm control? Temperature and fan control on OPI5 - Orange Pi 5 / 5B / 5 Plus - Armbian Community Forums Rock Pi4 pwm control - no overlay? - Rockchip - Armbian Community Forums
-
Reputation Points
- 1 reply
- 2.2k views
- 1 follower
-
-
Hello all, I got a problem after new update of armbian firmware through your own module (script). The left USB port on pinebook pro has stoped working at all. Before that was occasionaly after 6 -7 boot ups only one time not working (it is used for mouse). Now after x rebooting it doesnt work at all. The right USB port works without problems. On the left, also USB flash drive doesn't work. No idea, what could it be? Before, as already said, it has worked in 90%. Before firmware upgrade.
-
Reputation Points
- 6 replies
- 4.5k views
-
-
I have a custom PCIe x4 lane card that I'm trying to integrate with a RockPro64 SBC. This custom card has been tested with many users on different platforms including a linux x86 system. When I try this card in a RK3399 system, I get a strange result when I view the assigned address space with the lspci command. It appears the address assigned is the exact value of the BAR address size for each BAR. If I change the BAR size the assigned address changes to that value. Below is a dmesg dump along with a lspci output for my device. Device is [ad00:001e]. Any guidance? dmesg: [ 2.395091] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges: [ …
-
Hi, I've tried to setup the latest Debian 13 (Trixie) for the Renegade board. I can flash the image with no issue. The problem comes it boots up, prompts for root password. I can type in then press enter, and then it goes to login. This only happens on the Debian 13 (Trixie). I am using the Debian 12 XFCE imange no issue. I am not sure if this is a bug or what, but I loved to use Debian 13, I am trying to setup Docker with the latest OS.
-
This was working on the tinker debian release, so I'm thinking this sis some kind of s/w issue. Is there something I'm missing on how to enable this? Thanks! Dave
-
Reputation Points
- 21 replies
- 20.8k views
- 1 follower
-
-
I'm using the ps2 emulator and when I try to run a game I get an error message "OpenGL is not supported. Only OpenGL 3.0 was found" I'm using the version "Armbian 23.02 Jammy Gnome"
-
Reputation Points
- 4 replies
- 7.8k views
- 1 follower
-
-
Hello, Long time Gentoo and Raspberry Pi user, but I am interested in a more powerful Arm device. Will buy an Orange Pi 5 plus device if it meets my requirements. I am interested about dual or multiple boot: let's say Linux and Android or, at least multiple Linux distro - let's say Armbian and Gentoo. It is possible ? On Raspberry Pi 4 with a larger boot partition I switch content of /boot from boot/debian /boot/gentoo, have multiple partition on SATA SSD connected via USB edit root parameter in /boot/cmdline.txt and that way I choose which distro to boot. On Orange PI 5 (Plus) I read that SPI chip have to be flashed to choose the boot device fro…
-
Reputation Points
- 6 replies
- 15.7k views
- 1 follower
-
-
Hi, all. After I upgraded the system and rebooted, the secondary ethernet port(i.e. the LAN port) is gone. The system info: https://paste.armbian.com/ekotoqigos nanopi-r4s:~:% ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 68:27:19:ad:02:09 brd ff:ff:ff:ff:ff:ff in…
-
Hi @ all, long time reader, but never managed to register. Now it is time... as I'm not able to solve this myself, kindly asking for help. I'm stuck, my Orangepi 5 plus stops boot at this: Loading, please wait... Starting systemd-udevd version 252.36-1~deb12u1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... (initramfs) What happened before? Last year I bought the Orangepi 5 plus (8GB) and went ahead, testing everything out - having incredible fun with this little box. But with a way to old/slow sd card which finally failed two or three months ago. I went ahead and wrote the A…
-
Hello, I noticed that the system has created a swap partition by default. So, Where does the system default to creating swap exchange partitions??
-
Hi guys, I created another device tree overlay that I needed, to enable two user leds on GPIO. Specifically GPIO0_B7 and GPIO0_C0, which is pins 27 and 28 on the header. Posting it here in case someone needs it, like I did with with the SPIdev overlay too. Here it is: rk3308-user-leds.dts What I needed this for is ethernet port LEDs, since the original connector does not include them. To get standard ethernet LED behavior on these newly defined LEDs, you can do this (you need su access): modprobe ledtrig-netdev echo "netdev" > /sys/class/leds/rock-s0\:orange\:user1/trigger echo "netdev" > /sys/class/leds/rock-s0\:green\:user2/trigger e…
-
Reputation Points
- 10 replies
- 4.5k views
- 1 follower
-
-
The page for the NanoPi R76S has also an edge kernel (6.18) image. I noticed some issues related to sdcard and emmc. I know edge images are not officially supported and that is fine. But given the image is available I would like the parameters/configuration/conditions for the current available image. Could you explain the background or assumptions behind the 6.18 edge image for the R76S? (e.g., test conditions you used when building it)
-
Reputation Points
- 2 replies
- 2.1k views
- 1 follower
-
-
I have an interesting discovery that smells suspiciously like a kernel bug. I find it easiest to see this bug by running btop which shows a historical per core cpu usage graph so it's easy to see when one stops being used. You can see the same thing in ordinary top but it's less easy to see than with btop. I have a Radxa Rock 5B with an RK3588 chip that I have been stress testing to make sure the hardware is OK before I start to use it in anger. As part of that I ran `openssl speed -multi 8` to spin up 8 threads using 100% cpu each. On all other machines that I've ever done that with it runs all X cores at 100% until it runs out of tests or is Ctrl-C'ed. Watch…
-
Reputation Points
- 14 replies
- 1.9k views
-
-
I have spent a considerable amount reading docs and getting my head around building a custom default kernel & desktop image. Patching the kernel and optimising the desktop environment is working well. The remaining question is: How do I select a specific - kernel 4.4.174 (based on armbian-release 5.75) ? It defaults to 4.4.176 and 5.86.
-
Hi, Im pretty new to linux in general mostly used windows before. Is there a way to get waydroid work on armbian? I installed it but waydroid sais that the binder kernels are missing (1). When I follow the instruction to install the kernel modules using dkms I also get a failure (2). (1) ERROR: Binder node "binder" for waydroid not found (2) Error! Bad return status for module build on kernel: linux-headers-5.10.110-rockchip-rk3588 Anyone can help me with this? Thanks in advance!
-
Reputation Points
- 27 replies
- 17.4k views
- 1 follower
-
-
Hey everyone, I'm starting to lose my mind here. I've got an Orange Pi 5 which works great with a micro SD card. Now I got myself a nvme ssd and all I want to do is move my system from the sd card to the ssd. I've created an image of the sd card on my PC using "dd" and then wrote it on the ssd using dd again. It seemed to work fine, the only issue seems to be, that the UUID of the partitions on the ssd were the same as on the sd card, that's why I changed the UUID of the root partition on the ssd using "tune2fs -U random /dev/nvme0n1p2". I booted up the Pi with my sd card again and used armbian-config to flash mtdblock0 (boo…
-
Reputation Points
- 10 replies
- 29k views
-
-
See for more details but without using the overlay-user folder - I was not able to get the pwm to work on a fresh download.
-
Reputation Points
- 0 replies
- 1.7k views
- 1 follower
-
-
Hi, SD card did not load Armbian_25.8.1_Orangepi5_trixie_current_6.12.41_xfce_desktop. I noticed that in boot.cmd line 9 , rootdev is defined as /dev/mmcblk0p1. Should that be /dev/mmcblk0n1 or /dev/mmcblk0n1p1? I note that this file should not be edited and the armbianEnv.txt only refers to rootdev=UUID=7e27c862-0a39-41cd-891e-7d77ff7968fd. Is this an error or am I off course? If so where do I correct it? cheers
-
Hi , I have an ASUS Tinker board S and I installed Armbian 5.54 on SD card. Then, I want work on eMMC drive of ASUS Tinker board S but, Armbian no detect it. How can I work with eMMC drive in Armbian ? Here my board info: http://ix.io/1j2Z Thanks, see you.
-
Reputation Points
- 20 replies
- 14.5k views
- 1 follower
-
-
I downloaded the kernel source and kernel headers on a rk3288 rockchip (tinkerboardS) and noticed there was a mismatch between kernel version, armbian release and chipset (rockchip64) - see below. root@tinkerboard:~# uname -a Linux tinkerboard 4.4.174-rockchip #7 SMP Sun Feb 10 11:57:26 CET 2019 armv7l armv7l armv7l GNU/Linux root@tinkerboard:~# cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=tinkerboard BOARD_NAME="Tinkerboard" BOARDFAMILY=rockchip VERSION=5.75 LINUXFAMILY=rockchip BRANCH=default ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage root@tinkerboard:/usr/src# …
-
Hello, sorry if this has been answered somewhere else. I was just wondering how i upgrade my Orange Pi 5 running Arbmian 23.11.1 Bookworm w/ Linux 5.10.160-legacy-rk35xx to the latest Kernel. I tried using `sudo armbian-config` and updating via that with kernel upgrades unfrozen but it doesn't seem to work. Is there something I'm missing? Startup splash below: ___ ____ _ ____ / _ \| _ \(_) | ___| | | | | |_) | | |___ \ | |_| | __/| | ___) | \___/|_| |_| |____/ Welcome to Armbian 23.11.1 Bookworm with Linux 5.10.160-legacy-rk35xx System load: 4% Up time: 0 min Memory usage: 8% of 3.83G IP: …
-
Reputation Points
- 6 replies
- 8k views
- 1 follower
-
-
The overlay for the ap6275p seems to be missing in the new fresh 6.10 images. Haven't tried to compile a custom image yet (so might just be disabled in current build), but how could I help to bring this overlay to the official image?
-
Reputation Points
- 1 reply
- 2.8k views
- 1 follower
-
-
Hello OPI5 users. Running Joshua Riek's Ubuntu distro, I keep getting stability issues. Perhaps because I keep using Xorg. Perhaps because hardware acceleration is buggy. In the past I used super stable Armbian OPI5 distro's without hardware acceleration. Infact I still use Armbian on another RK3588 box, I don't think it has EVER crashed, running docker, Mosquito, HomeAssistant, and a buch of other things. Now that my Orange Pi 5 gets a slightly more serious use as webserver, I really like to get rid of the unpredictable Xorg crashes, and gladly would sacrifice HW acceleration for stability. My situation is this: Using JR Ubuntu Because I …
-
If you'd like to get the LEDs working with armbian, you can run these commands (or one of the other ones if you want different indications): run modprobe ledtrig-netdev to check if it's loading the driver properly. If not, add the file /etc/modules-load.d/ledtrig.conf add just this line: ledtrig-netdev Then, create /etc/tmpfiles.d/leds.conf and add this: w /sys/class/leds/green:lan/trigger - - - - netdev w /sys/class/leds/green:lan/device_name - - - - eth0 w /sys/class/leds/green:lan/link - - - - 1 w /sys/class/leds/green:lan/tx - - - - 1 w /sys/class/leds/green:lan/rx - - - - 1 w /sys/class/leds/green:wan/trigger - - - - netd…
-
Hi there, Just got Orange Pi 5 8GB and have no idea where to begin. I have a microSD card available, but no writer. I had the idea to boot from USB thumbstick and then write the SD card using the port on the Orange Pi 5, then I can boot from SD card. Is this possible? What image and method do I need to follow in order to boot from a simple 32GB USB Sandisk thumbstick? Thank you!
-
Reputation Points
- 4 replies
- 5.3k views
- 1 follower
-
-
Hey there, I now have my Nanopi R4S for quite a while but never got it to run stable over a longer period of time. Now I finally connected another board to its debug serial in the hopes to catch something that causes the board to freeze. Well this is what I have collected: https://p.na4.eu/?bc818aefadc9b5b2#DAunYKXghkaqcLhh8SLWMKTWABewpwPJRnHMHDemR98Y The log is complete, there is nothing missing between 08:51 and 19:14. This is how I collected it. Basically during the state of throwing errors the board becomes unresponsitive and continously heats up. Active cooling was in place so no danger of overheating. https:/…
-
Hello friends, htop does not show me the temperature, I am attaching information about my system (I have the libsensors library installed). If someone can help me please. Thank you. OS: Armbian 24.5.0-trunk.89 trixie aarch64 Host: Xunlong Orange Pi 5 Kernel: 6.8.0-rc1-edge-rockchip-rk3588 Uptime: 1 hour, 14 mins Packages: 333 (dpkg) Shell: bash 5.2.21 Terminal: /dev/pts/0 CPU: (8) @ 1.800GHz Memory: 187MiB / 7687MiB
-
Reputation Points
- 3 replies
- 4.2k views
- 1 follower
-
-
Hi, I read everything I could possibly find on the DP-Alt mode for the RockPro64 and came to the conclusion that no Distro is offering that right now. However, the Pinebook Pro seems to have support via a Kernel Patch. Can the Pinebook Pro Kernel be installed on the RockPro64? Is there a repository for Armbian Kernels? Thanks very much.
-
Reputation Points
- 14 replies
- 6.4k views
- 2 followers
-
-
Hi I dd the Armbian_25.11.1_Rock-5c_trixie_current_6.12.58_minimal.img to a SD card (/dev/sdc) and then run a fsck -f /dev/sdc1 and got errors: sudo fsck -f /dev/sdc1 fsck from util-linux 2.39.3 e2fsck 1.47.0 (5-Feb-2023) Pass 1: Checking inodes, blocks, and sizes Pass 2: Checking directory structure Entry '.' in ??? (1065) is duplicate '.' entry. Fix<y>? .... Tried few SD cards, same result. Tried those SD cards with other images, i.e. Armbian_24.8.4_Rock-5c_bookworm_vendor_6.1.75_minimal.img no problems. Could anybody verify this behavior? Thanks Chris Armbian_25.11.1_Rock-5c_trixie_vendor_6.1.115_minimal.img i…
-
Hello, I’ve seen in the latest release Armbian now supports installing to UFS but can’t really see much information about going about this? I boot into the SD card and I’ve tried both installing a new copy to the UFS, which seems to do something but booting only gets as far as initramfs, and copying existing install from SD card which just fails with the following: “No bootable install method is available for /dev/sda on this system (no EFI firmware, no GRUB, and no board u-boot support).” I have tried both Debian and Ubuntu minimal images on vendor and current kernels. I did have a FriendlyElec image on there before but used Rkdevtool to erase …
-
Reputation Points
- 1 reply
- 607 views
-
-
I finally found an official source code on the download page of OrangePI that has a version of wiring pi with support for the Orange PI 5 - unfortunately that code is not on the github of orangepi yet. What would be the best way to get this code and the gpio tool into armbian? Build a PPA and package for that one? I don't mind forking their repo and adding the mods but I'm not familiar with generating debian packages.
-
Reputation Points
- 10 replies
- 25.6k views
- 1 follower
-
-
Hi all Armbian fans, As of today, I checked officially platinum supported Armbian version for Orange Pi 5. I was amazed how low performing is armbian image. I was using latest armbian with HW install procedure at: https://redirect.armbian.com/orangepi5/Jammy_legacy_gnome , and Ubuntu from https://github.com/Joshua-Riek/ubuntu-orange-pi5/releases/download/v1.11/ubuntu-22.04-preinstalled-desktop-arm64-orange-pi5.img.xz Both glxinfo -B says: Accelerated : yes Armbian glmark2 Score: 705 Ubuntu glmark2 Score: 1285 Difference is HUGE When we could expect any "normal" Mali…
-
None of the images from https://www.armbian.com/rockpi-s/ work (neither minimal nor cli). I tried writing minimal image onto SD NAND and tried booting both cli and minimal from SD card. I tried 2 different SD cards too. Board was connected through UART0 to PC and while I get output when I use rkdeveloptool, there is no output when trying to boot normally. However, latest image from https://github.com/radxa/rock-pi-s-images-released/releases works (rockpis_debian_buster_server_arm64_20210924_0412-gpt.img) does boot if I write it to SD NAND or SD card. I have V1.3 with RK3308 and 1GB SD NAND.
-
Reputation Points
- 10 replies
- 8.7k views
- 1 follower
-
-
It seems that the HDMI output does not have any option beyond 1080P. Tried multiple monitors. The font size at uboot stage seems right but the resolution maxed out at 1080P after kernel starts. Tried Armbian 24.2.1 with 6.6.16. Could be related with this: https://forum.manjaro.org/t/rk3399-hdmi-output-for-resolutions-different-than-1080p/90644. but patches should be applied at Kernel 6.4: https://www.phoronix.com/news/Linux-6.4-imx25-Rockchip-4K Attached is the screenshot when connected with DELL 25inch monitor. Should have 2K option. diagnoses: https://paste.armbian.com/gaketoluye Thank you
-
Reputation Points
- 4 replies
- 3.8k views
-
-
Hi, last night a set of updates was installed and I rebooted the Orange Pi 5+ this morning. After the reboot I've seem to have lost the connection to the Orange Pi 5+, it is normally connected without a screen so I access it through SSH and the Open Media Vault web GUI. I've tried to connect it to a screen and then it seems to boot up just fine. Looking around with the screen connected it seems like the network cards aren't detected. My Linux skills are very limited but "sudo lshw -class network" shows nothing. One detail is that my router seems to detect it when it's connected and gives it the normal IP address that I've set in the 192.168.0.x ran…
-
I just tested the latest, 2025 May, built image with default/recommended options and there are some missing features. Here is what I have tested: LAN yes WiFi yes BT yes USB3 *partly, some devices are not detected at all, some will take a few minutes before detected* GPU Mali-G610 (Panfrost) HDMI audio *no* Fan control yes temp. sensor htop *no* Temp. sensor Gnome *no* Other: some cursor graphic glitches Armbian-unofficial_25.05.0-trunk_Rock-5c_noble_current_6.12.28_gnome_desktop.img Any ideas on how to get more features supported?
-
Reputation Points
- 6 replies
- 5k views
-
-
It's been a while since I used Armbian. I have tons of ARM SBCs from a few years back because I think they're fascinating but they either wind up being too slow or just not worth using it for whatever since x86 "SBC like" boards exist and are pretty cheap. Fast forward to now and I'm doing some touchscreen development and just because of how I have things setup I needed 3 things, I2C, Interrupt capable GPIO and an actual DisplayPort. That combination of things is surprisingly hard to find. I had a couple of things on hand, (Seeed Odyssey x86, Odroid H2/H3, Rpi's, Nvidia Jetson Nano). I spent way more time than I should have trying to make each of these work, i…
-
I got a radxa rock 5t and trying to install armbian(https://www.armbian.com/radxa-rock-5t), arimbian NOT boot and I can see the indicator light on the board is showing a steady green light. I boot with the official image https://docs.radxa.com/en/rock5/rock5t/low-level-dev/maskrom/linux and insert the sd card(with armbian img), and run such command, then I can boot armbian from SD card sudo dd if=/dev/mmcblk0 of=working_idbloader.img bs=512 skip=64 count=8000 sudo dd if=/dev/mmcblk0 of=working_u-boot.itb bs=512 skip=16384 count=8000 sudo dd if=working_idbloader.img of=/dev/mmcblk1 bs=512 seek=64 conv=notrunc sudo dd if=working_u-boot.itb of=/dev/mmcblk1 bs…
-
Reputation Points
- 5 replies
- 4.6k views
- 2 followers
-
-
Only "chirps and chips" come through during extended playback. Only hdmisound device is affected, not analog. Duplicate of improperly "resolved" thread Armbian 22.02 Bullseye Kernel 5.15.25-rockchip64 Armbian 22.02 Bullseye Kernel 5.16.16-rockchip64 working in 5.10.60-rockchip64 steps to reproduce: aplay -D plughw:1,0 /usr/share/sounds/alsa/Front_Right.wav dmesg | grep es83 [ 10.077582] es8316 1-0011: Failed to get IRQ 0: -22 card 0: Analog [Analog], device 0: ff890000.i2s-ES8316 HiFi ES8316 HiFi-0 [ff890000.i2s-ES8316 HiFi ES8316 HiFi-0] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: hdm…
-
Reputation Points
- 2 replies
- 3.5k views
- 1 follower
-
-
Hi everyone! I am struggling with audio input. Output audio from LINEOUT pins works fine out-of-the-box! What about the audio input? To begin with I have tested the arecord command with these error messages… TEST 1 root@rockpi-s:~# arecord -f S16_LE -d 10 -r 16000 --device=“hw:0,0” test-mic.wav Recording WAVE ‘test-mic.wav’ : Signed 16 bit Little Endian, Rate 16000 Hz, Mono arecord: set_params:1358: Channels count non available TEST 2 root@rockpi-s:~# arecord -f S16_LE -c 2 -d 10 -r 16000 --device=“hw:0,0” test-mic.wav Recording WAVE ‘test-mic.wav’ : Signed 16 bit Little Endian, Rate 16000 Hz, S…
-
With the vendor kernel, my logs are getting flooded with drm error messages Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:r…
-
Reputation Points
- 2 replies
- 2.2k views
- 1 follower
-
-
Connecting a usb keyboard doesn't seem to work with 7.1 .. [ 2.836541] usb 7-1: new full-speed USB device number 2 using ohci-platform [ 3.024538] usb 7-1: device descriptor read/64, error -62 [ 3.304535] usb 7-1: device descriptor read/64, error -62 [ 3.596542] usb 7-1: new full-speed USB device number 3 using ohci-platform [ 3.780527] usb 7-1: device descriptor read/64, error -62 [ 4.076543] usb 7-1: device descriptor read/64, error -62 [ 4.180566] usb usb7-port1: attempt power cycle [ 4.372529] usb 7-1: new full-speed USB device number 4 using ohci-platform [ 4.780541] usb 7-1: device not accepting address 4, error -62 [ 4.96452…
-
I have a question or at last 2. 1.Where to connect outside diode to thinkerboard . 2.How to turn off/on it from command line.
-
Ok so I think I have this figured out. It doesn't work at all in Armbian 23.05.1 with the 6.x kernel no matter what I try. It does work in the older Armbian 23.02.2 Jammy (kernel 5.15.93) but the given instructions didn't work for me and needed additional commands. I had to enable the rk3328-opp-1.5ghz overlay or else the max frequency was locked to 1296 MHz. I also found the MAX_SPEED value in the instructions to be too low. To get it to work in 23.02.2: First you have to enable the rk3328-opp-1.5ghz overlay in armbian-config (System > Hardware > rk3328-opp-1.5ghz) or just add it to the overlays line in /boot/armbianEnv.txt and reboot. Next open the /et…
-
Reputation Points
- 0 replies
- 2.5k views
- 1 follower
-
-
Hi, I am not able to make Radxa Camera 8M to work with Armbian_24.5.3_Radxa-zero3_bookworm_vendor_6.1.43_minimal.img and Armbian_24.5.1_Radxa-zero3_noble_vendor_6.1.43.img gst-launch-1.0 v4l2src device=/dev/video0 io-mode=4 ! videoconvert ! video/x-raw,format=NV12,width=1920,height=1080 ! jpegenc ! multifilesink location=/home/a2t/test.jpg Pipeline is live and does not need PREROLL ... Pipeline is PREROLLED ... Setting pipeline to PLAYING ... New clock: GstSystemClock ERROR: from element /GstPipeline:pipeline0/GstV4l2Src:v4l2src0: Internal data stream error. Additional debug info: ../libs/gst/base/gstbasesrc.c(3132): gst_base_src_loop (): /GstPipeline:pipeline0/G…
-
Reputation Points
- 5 replies
- 8.8k views
- 3 followers
-
-
Hello all, I am running an Orange Pi 5 board with Armbian on a SD Card and I realized that my /var/log path is constantly full, with it being at /dev/zram1 It gets full at 50Mb with the file /var/log/samba/cores/smbd/core taking up all the space I have not managed to read this file, so I can't tell what kinds of errors are showing up. My OpenMediaVault and samba setup are running perfectly fine, and even though I delete this core file, it shows up again during reboot. I have tried to set enable core files = no in smb.conf With no sucess. The file continues to show up during reboot. Any ideas how to solve this? …
-
Reputation Points
- 7 replies
- 8.7k views
- 1 follower
-
-
I installed Desktop images with Armbian Linux v6.1 Ubuntu 24.04 (Noble) Gnome (Zero 3W) And out of the box after installation I get the message -bash: fork: retry: Resource temporarily unavailable (I have to work through the com port, because because of this error ssh and the desktop cannot work) I checked the performance of the equipment by installing Debian 11 from Radxa, the equipment works correctly (CPU RAM eMMC). Has anyone encountered this problem?
-
Reputation Points
- 2 replies
- 2.8k views
-
-
I have an Armbian installation on the NVMe drive and I'm trying to switch back to boot from SD card. In `armbian-config` I messed up the boot settings by leaving the root fs type unchanged, (SD card is in fat32 but NVMe partition is ext4). Now the board boots into initramfs prompt. Here's what I've already tried based on search and ChatGPT: Mount the NVMe partition to `/mnt` then chroot to it, this did work but the `/boot` partition was not mounted inside of the chroot so I can't fix boot env. I also tried `switch_root` but it's not available in the initramfs prompt. Update `/proc/cmdline` to change the root fs back to the Armbian partition…
-
Reputation Points
- 1 reply
- 6.6k views
- 1 follower
-
-
Hi there I'm using Ubuntu 24.04 (Noble) KDE Neon image from may 26, 2025. After download this image and installing it, Wayland was working fine, not problems at all. Then, after a system upgrade, if i choose Wayland from session manager, the system freezes and i can't boot with Wayland, only X11... Before the update, the system was smooth, now it's really laggy....Like i said, i'm using Desktop image with Armbian Linux v6.12 KDE Neon (Ubuntu 24.04) There's something wrong with the update Anyone knows why is this happening, and any turnaround to use Wayland again?
-
Reputation Points
- 11 replies
- 6.9k views
- 1 follower
-
-
Hy all, For some time now I have a Rock 5b + with 16Gig memory. The problem I have is playback video' s in youtube. Video's are not even watcheble in the lowest resolution. Other 4k video' s play fine. I tried several bechmark video' s from online sources. I looked around to see if others experiance the same problem but cannot find anny clu in this matter. I use Armbian ver. 25.5.1 Do others have the same issue? Is there a soltion for this problem? Also I find this board not the fastest. It's a bit faster than mi RPI5 with 4Gig mem. The PI5 plays HD on youtube. I also have a OrangePi 5 ultra with 16 gig memory on stock Orangepi ubu…
-
Reputation Points
- 1 reply
- 1.9k views
- 1 follower
-
-
I've tried to reinstall multiple times. Armbian runs fine and i am able to SSH and do everything on it, but hdmi display plugged in gets no signal. I installed Armbian 22.11 Jammy XFCE and non. Both give me no output. I'm using a big enough power supply, and nothing. I am attaching the output i got on the armbianmonitor U http://paste.debian.net/1270237/
-
My Libre Computer Renegade wouldn't boot from its pluggable eMMC this morning. I worked around the issue by booting from an SD card, setting up a chroot environment for the eMMC card, and switching to an older kernel on the eMMC. Obviously, it would be better if the current kernel supported booting from eMMC. This may be related to and
-
Reputation Points
- 1 reply
- 2.5k views
- 1 follower
-
-
Hello everyone, I flashed the armbian into my tf cand and inserted it into my OrangePi 5 Plus, with my fans inserted to the specific socket on board (2pin, 1.25mm, 5V, PWM3_IR_M1). However, when I booted it, the fans was running constantly instead of controlled by temperature dynamically, like the official OS images that did only the fans running when the temperature over 50 celsius. I wanna know how to configure my OS to enable the temperature-controlled fans like the official images. The offical documents shows: Linux uses the default pwm-fan drivers to control thye fans and the device tree was defined in orange-pi-5.10-rk3588/arch/arm64/boot/dts…
-
Reputation Points
- 2 replies
- 5.4k views
- 1 follower
-
-
When running PassMark on my Rock Pi S running Armbian 25.11, the system completely freezes, including the serial console. The blue TF card read/write LED stays lit, and OOM events are visible on the serial console. This freeze typically lasts over half an hour before the system recovers as the blue LED turns off. OOM events also occur on the stock kernel 4.4 system, but it doesn't freeze. I really don't want to use the 4.4 kernel system, but how can I optimize it? Below is my system configuration and log output: Translated with DeepL.com (free version) pi@Pi-s:~$ uname -a Linux Pi-s 6.12.58-current-rockchip64 #3 SMP PREEMPT Thu Nov 13 20:34:41 UTC 2025 …
-
After upgrading armbian to 26.2.1 with kernel 6.18.10 performances on WAN interface dropped to 20Mbps for a single TCP connection. The interface is end0, renamed from eth1, driver from ethtool -i is "st_gmac". I used armbian-config to rollback to kernel 6.12.58 and performances are ok now. Will it be fixed in the future kernels ?
-
Reputation Points
- 1 reply
- 1.3k views
- 1 follower
-
