Amlogic meson
Quick links to search tags:
Banana Pi CM4-IO, Banana Pi M2S, Banana Pi BPI-M2 Pro, Banana Pi M5, JetHub D1, JetHub H1, Khadas VIM1, Khadas VIM1S, Khadas VIM2, Khadas VIM3, Khadas VIM3L, Khadas VIM4, La Frite, Le Potato, Sweet Potato, Odroid C1, Odroid C2, Odroid C4, Odroid HC4, Odroid N2/N2+, Radxa Zero
-
This is what the network status looks like immediately after turning on the power: $ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host noprefixroute valid_lft forever preferred_lft forever 2: end0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether d6:e3:db:f5:f2:24 brd ff:ff:ff:ff:ff:ff inet 192.168.100.124/24 metric 100 brd 192.168.100.255 scope global dynamic end0 valid_lft 2…
-
Reputation Points
- 2 replies
- 3k views
- 1 follower
-
-
What should the correctly enabled I2C service (for a 40x2 LCD) look like on Bananapim2pro? Should I edit the armbianEnv.txt file and add, for example, the following entry: overlays=i2c0 i2c1? The armbian-config service is a bit confusing, and after editing it, I get this: ........................ verbosity=1 console=both overlay_prefix=meson fdtfile=amlogic/meson-sm1-bananapi-m2-pro.dtb rootdev=UUID=a4fb8074-c453-45da-ab31-4d61dca46cfa rootfstype=ext4 overlays=i2cA i2cB usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u .................. There are other options, but they probably don't apply to bananapim2pro. : sm1-odroid-c4-i2c0 …
-
I've recorded Armbian_20.11_Lafrite_focal_current_5.9.6.img.xz to an usb drive and booted it on La Frite with the latest firmware u-boot-2020-07-r7.bin from http://share.loverpi.com/board/libre-computer-project/libre-computer-board/aml-s805x-ac/firmware/. Armbian boots but text is almost unreadable. I guess, I have to tweak some linux boot parameters but I don't know how to do this without GRUB. I tried holding u-boot button during a launch of the board but it gives no effect. How should I edit kernel parameters on La-Frite? Is there any other solution?
-
Reputation Points
- 3 replies
- 6.2k views
- 2 followers
-
-
Hi, I installed armbian_23.8.1_Radxa-zero_bookworm-current_6.1.50 on Radxa Pi Zero eMMC and I have an USB SSD drive connected as storage. Everything worked fine using it as a NAS but if I reboot there is an endless loop of reboots with the core message "scanning bus usb0ff5000000 for devices... Synchronous Abort handler, err 0x56000010". If I disconnect the USB drive it boots fine and when reconnect it after the boot process, the drive works fine. But I really need a system that is able to boot without temporarely disconnecting USB. I tried different combinations of USB with two different hubs or without hub. There are no boot flags on the partitions. I completely de…
-
Hi, I downloaded the jammy xfce image for ODROID C2 today: MD5SUM 033fbc0babb56db5388b4c707a2fc0ce Armbian_23.11.1_Odroidc2_jammy_current_6.1.63_xfce_desktop.img.xz After flashing it onto my SD card with xzcat and dd, I tried to boot with my Odroid C2 ending up with this error message: ALERT! UUID=75e23441-f5ee-4479-a484-7060ccd898ae does not exist. So I put the SD back into my PC and checked with gparted: the UUID of the partition that I have on my SD card seems to have exactly the UUID that was not found. In fact the boot until that error message lastet quite long, so I expect that the…
-
Hi. I recently purchased a few DS18B20 sensors. I'm having troubles setting up 1-wire on the newest armbian: root@odroidn2:~# uname -a Linux odroidn2 5.8.5-meson64 #20.08.1 SMP PREEMPT Tue Sep 1 18:47:20 CEST 2020 aarch64 GNU/Linux My DS18B20 adapter is connected to "GPIOX_7(#)" as suggested on Odroid forum: https://forum.odroid.com/viewtopic.php?p=305664#p305664 Using the official Ubuntu 18.04 image with 4.9.230-76, I was able to find devices in "/sys/bus/w1/devices". Now, I'm trying to do the same thing on Armbian. I added to: /boot/armbianEnv.txt overlays=w1-gpio param_w1_pin=GPIOX_7 param_w1_pin_i…
-
Reputation Points
- 3 replies
- 7.1k views
- 1 follower
-
-
Can OpenVFD be installed on the Armbian image for LePotato?
-
My current HC4-setup consists of 1 SSD and 1 HDD. The SSD contains the most recent Armbian-image (Buster-based) (https://redirect.armbian.com/odroidhc4/Buster_current). Long story short: it won't boot from SSD, and Google tells me it is because Armbian is not compatible with Petiboot. Armbian suggests the following solution: "Important: To be able to boot clean Armbian mainline based u-boot / kernel experiences, you need to remove incompatible Petitboot loader that is shipped with the board. From the Petitboot, go for “Exit to shell” and these commands to remove the Petitboot:" # flash_eraseall /dev/mtd0 # flash_eraseall /dev/mtd1 # flash_eraseall /de…
-
Reputation Points
- 19 replies
- 21.7k views
- 1 follower
-
-
Hi, has anyone got the Odroid VU7-C display to work on a Odroid N2+ running headless Armbian Jammy? Running the hardkernel stock 22.04, which is still on linux kernel 4.9, it works fine. I've already tried to change a few boot params in /boot/boot.cmd, inspired by https://wiki.odroid.com/accessory/display/vu_series/vu7/vu7#tab__odroid-n2 like setenv display_autodetect "true" or setenv disable_vu7 "false" setenv hdmimode “800x480p60hz” setenv voutmode "dvi" Am I correct to run mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr as root after each change in boot.cmd? I noticed in the hardk…
-
Reputation Points
- 0 replies
- 2.5k views
- 1 follower
-
-
Hi, Like the title says the UART overlays are not working on the armbian radxa zero device if I use the official out-of-the-box image. Using the armbian-config I can enable UART A and B but these changes do not reflect in the /dev/tty devices (using other distros is can see /dev/ttyAML0, /dev/ttyAML1 and /dev/ttyAML4). Unless the devices are called something else i confirm that the overlays are not working. That being said I want to recompile a armbian image with the correct overlays but I am a complete noob. Here is my plan : i successfully compiled a minimal cli armbian image for the radxa zero without any…
-
Is there, or will there be, an Amlogic or Banana Pi issued GPU blob to run Vulkan? On v6 kernel ideally Amlogic does have a history of allowing this, for Odroid and Khadas. Duncan
-
Reputation Points
- 0 replies
- 2.2k views
- 1 follower
-
-
I've tried shutdown -h now, poweroff, shutdown -h, all results in a reboot instead of shutdown. I've searched and haven't found a solution, just other people with the same problem. I'm running "Armbian_24.2.1_Lepotato_bookworm_current_6.6.16_cinnamon_desktop.img", has anyone found a solution to this problem? I tried raspbian on the le potato and that will shut down but gives me other issues when installing openhabian. Armbian just seems to work otherwise but I'd like a clean way to shutdown when needed so I don't risk corrupting my sd card.
-
Reputation Points
- 5 replies
- 5.2k views
-
-
Armbian current: It seems that the N2+ is [i]immune[/i] to Chrony and systemd-timesyncd. The only way I can set the date/time is manually through date -s. # systemctl status systemd-timesyncd ● systemd-timesyncd.service - Network Time Synchronization Loaded: loaded (/usr/lib/systemd/system/systemd-timesyncd.service; enabled; preset: enabled) Active: active (running) since Mon 2025-11-24 13:06:59 PST; 31min ago Invocation: 50da85c1116348dbbd83cca270da6ff8 Docs: man:systemd-timesyncd.service(8) Main PID: 1185 (systemd-timesyn) Status: "Idle." Tasks: 2 (limit: 4227) Memory: 1.6M (peak: 2.3M) CPU: 79ms C…
-
Hi, is there a way, how to check that image in download section is ok? I have Odroid HC4 with good PSU, both old and new card, flashed by Etcher and Rufus, keyboard plugged in USB, no SATA disks at the moment. I'm able to boot Focal 4.9 kernel (however with some errors after the boot). I've removed Petitboot with flasherase first, I've checked SHA checksum. Edit: File I've downloaded is: Armbian_20.11.6_Odroidhc4_focal_current_5.9.14.img.xz SHA: 9930f984eca2a72b3c22953ee6381c95da528b2a355dd9f429da38d1409f7b1f *Armbian_2 Any ideas what is wrong? Thank you.
-
Hello All, I spent mainly a week figuring out why it was a nightmare with cinnamon on debian I thought it was a matter of cinnamon version and/or mesa version of panfrost but it was a modeline detection problem from xorg. After trying my luck I finally discover where the bad duck resided on debian versions : - bullseye who was lagging , managing to use mali accel but overflowded with log errors - bookworm was loosing HDMI signal just after login in.. I will only talk about bookworm In fact, cinnamon internal xrandr, tool who detect the screen modelines, fails to access and to grab screen EDID modelines like xrandr did. it resul…
-
Hi, I tried to migrate my odroid C2 form corelec to armbiam bookworm 6.1.6.63... but i'm having some problems with network... i need to fix on switch the limit bandwith at 100mb/s even impossible to have network... When it's ok, if i tried to force config with ethtool (network freezes everytime)... and in every case, after some hours.. the network freeze.. So i'm looking for an armbian with a good stability and not too old.. Regards,
-
I have a bunch of these boards and a few friends that would like to use them. I am having problems getting UART on the GPIO to work even using Libre Computers Wiring tool. Is there any info on getting Armbian Device Tree Overlay to work with the potato? I really need UART on the GPIO. CAN0 would be a very helpful creature comfort but if i cannot get UART to work properly i have extremely dwindling odds of getting CAN0 to function properly. Any info that can point me in the right direction is welcome.
-
Reputation Points
- 1 reply
- 3k views
- 2 followers
-
-
Hi ! I was trying to use SPI communication with Banana Pi M2 Pro. I am currently using Armbian 26.5.1 and I realized that I cannot find spidev from /boot/dev/ . I tried loading all dtbo files from armbian-config but still I can't get SPI. Is there something that I haven't check yet?
-
Reputation Points
- 2 replies
- 833 views
- 1 follower
-
-
Hi all How can I enable the rtc clock in the Odroid HC4? I know nothing about device tree and overlays, but the Hardkernel Ubuntu image has an overlay to enable: wiki. I didn't find anything similar in the armbian image. Could be related to this this PR for the N2 model? Thanks
-
Reputation Points
- 6 replies
- 8.5k views
- 1 follower
-
-
Logs: https://paste.armbian.com/kasujazuwo Hi, I've been looking to run the desktop version of Armbian on the M5 however it will not start (blank screen, no signal). I can see the Debian Icon at startup, and the Armbian Icon at shutdown. startx does not bring it up, however sudo startx will but I'm not sure if this is the best way. I have tested: Armbian_22.11.3_Bananapim5_bullseye_current_6.1.4_gnome_desktop.img Armbian_22.11.3_Bananapim5_bullseye_current_6.1.4_cinnamon_desktop.img and both are the same. Any ideas are appreciated! Thanks.
-
Hi, Does anyone know how to get rid of the error on Odroid N2+ ? The error appears after some time of using GUI app on XFCE DRM_IOCTL_MODE_CREATE_DUMB failed: Cannot allocate memory Failed to create scanout resource
-
Reputation Points
- 2 replies
- 4k views
- 1 follower
-
-
I’m trying to define a simple sound card where I just have a TDM output on TDMA. Now I have defined my device tree as: sound { compatible = "amlogic,axg-sound-card"; model = "BPI-CM4IO"; audio-aux-devs = <&tdmout_a>; audio-widgets = "Speaker", "Speaker1 Left", "Speaker", "Speaker1 Right"; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", "TDM_A Playback", "TDMOUT_A OUT", "Speaker1 Left", "SPK1 OUT_A", "Speaker1 Right", "SPK1 OUT_B"; clocks = <&clkc CLKID_HIFI_PLL>, <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>; assigned-clocks = <&clkc CLKID_HIFI_PLL>, <&clkc CLKID…
-
Reputation Points
- 0 replies
- 2.6k views
- 1 follower
-
-
I'm trying to complete the installation of Armbian onto the HC4 (HC4-P if that changes anything). With a fresh SD card I run sudo dd if=Armbian_22.11.1_Odroidhc4_bullseye_current_5.19.17.img of=/dev/sdb status=progress plug in the card to the board, plug in the ethernet cable, hold down the boot switch, and plug it into power. It all seems to run correctly: I can SSH into the board and I complete the initial steps to set-up the installation (root pass, default shell, username, real name, and locale). However it does not seem as I can access the SPI FLASH device. Running the following commands from the HC4 page do not work as there are no mt…
-
Banani Pi M5, Armbian_23.02.2_Bananapim5_bullseye_current_6.1.11_xfce_desktop into SD card, USB drive connected and auto mounted in fstab. Boot loop looking for system into USB. I have to disconnect USB then it boots up from SD. Any help?
-
Hello experts and members, Any possibility of multi booting armbian via petitboot from microsd card or usb or emmc in odroid n2 among other OSs.
-
Reputation Points
- 0 replies
- 1.2k views
- 1 follower
-
-
Le Potato is the first board from Libre.computer: https://libre.computer/products/boards/aml-s905x-cc/ Basic information is on the link above, here's the TL;DR: Raspberry Pi 2 form factor clone, with 64-bit quad-core Amlogic S905X 1 or 2 GB RAM eMMC and SD support HDMI 2.0 for 4k support 100 Mb Fast Ethernet Extra headers for I2S, UART, etc (nice feature I think) IR receiver Advertised to have low power consumption Powered via micro-USB based on: Amlogic P212 reference board Use Case: Media Player (retro gaming?) I've been using a board now for a few weeks, I ha…
-
Reputation Points
- 5 replies
- 11.3k views
- 1 follower
-
-
Hello, I've tried to use the bug reporting tool but unfortunately it did not work (armbianmonitor -u did not work, and it was too big for http://paste.debian.net/), so I've posted here. I'm trying to use a PCTV 292e plugged into the USB2 port of my Odroid N2. I have the correct firmware for this device downloaded into the /lib/firmware/ folder however I have the errors: writing to i2c device at 0xc8 failed (error=-5) I think it is a USB issue as it does work in the USB3 ports, but I am unsure. Logs below. If there is any more info I need to supply please let me know. Thanks. armbianmonitor -U 1 2 ### Act…
-
Reputation Points
- 0 replies
- 8.1k views
- 1 follower
-
-
I tried the 5.10 images. Both Jammy and Buster. Both just give a black display, but the display does wake up(background LED is on) All LED's stay on. With sid 5.19 it boots normally. Blue LED flashes. Display works.
-
Hi all, after installing the latest version of Armbian (Jammy 6.1.11 desktop) I found that HDMI monitor audio is not working. With the Ubuntu MATE version of odroid the audio worked. Armbian seems more powerful and its look is much better than MATE, I hope I can solve all the problems because I don't want to go back to MATE anymore, How can I make HDMI audio work? Thanks in advance... PS. I have already updated the firmware to full with the WiFi USB stick problem which has since been resolved
-
Reputation Points
- 4 replies
- 7.2k views
-
-
VIM2 responds to pressing the function button three times, with the blue LED blinking briefly, but after that nothing happens. The only thing that worked was connecting via UART and after resetting I got this (see screenshot). Where, in addition to the lack of loading, this line confuses me DDR3 chl: Rank0+1 @ 912MHz - FAIL Apparently, I have a problem with u-boot, and maybe a hundred more. I would like to get advice on which direction should I move? In advance, thank you very much to everyone who responded!)
-
The latest Armbian IoT image for Khadas VIM4 does not boot. sha256sum: 69b10797369fd572d590aeb0dd7b28a4ebc5882cec8db8daf592db7b158bf141 Here is the log from the serial debug console. Spoiler [...] Hit any key to stop autoboot: 0 Setting bus to 6 _find_partition_by_name()-200: do not find match in table boot _find_partition_by_name()-200: do not find match in table boot error partition name! 4096 bytes read in 1 ms (3.9 MiB/s) _find_partition_by_name()-200: do not find match in table boot _find_partition_by_name()-200: do not find match in table boot error partition name! 4194304 bytes rea…
-
Minor annoyance, but wondering if there's a way to fix this on boot ? It's happened on all releases i've tried (emmc) enough of an annoyance now to ask about it. i've tried setting various resolutions in the boot.cfg but that doesn't seem to make a difference? connected via hdmi When I first turn it on I see this; Then it goes to this Then, i see normal dmesg and it's all usable.
-
Reputation Points
- 2 replies
- 3.6k views
- 1 follower
-
-
board ist lafrite with 512mb, 8gb emmc tried all possible ports for i2c. first by configuring with armbian-config and activating i2c port a and b. then manual by writing an overlay to activate i2c_ao and deactivate the uart on pins 3+5; also tried pins 27+28; i2cdetect -y bus-nr (0, 1) never detected anything; i2cdetect -l gave me correct ports; i2cdetect -y for the hdmi-port allways worked.
-
Reputation Points
- 10 replies
- 6.3k views
- 2 followers
-
-
Hi Seems like headers are missing xtables-addons. During system update it failed and after reboot it stuck. After manualy fixing symlinks for images it booted up, but i couldn't manage to make xt_geoip working again. Tried removing headers and installing them again with armbian-config but still the same
-
So, I've been struggling to figure out the reason behind this problem. I have 4 Le Potatoes, all connected to a 100 mbps switch. Each of them have a 32 GB Samsung SD Card EVO. Initially, the problem was that my SSH session would hang at random usually when I download something. I can't SSH again unless I reboot the PI (I didn't bother waiting longer than 5min) Initially, I thought SD Cards were bad, I moved them around, done reinstalls. I'm also using SD Formatter to format them and Etcher to install them. Still, this freezing problem had no consistent behavior according to PI hardware or the SD cards.. For Power, I'm u…
-
Reputation Points
- 72 replies
- 33.9k views
- 3 followers
-
-
Armbian_23.11.1_Odroidn2_bookworm_current_6.1.63.img.xz was downloaded and flashed to SD card. System booted OK from the SD card and successfully started the OS. Then I used armbian-config to write the root file system to an SSD. After reboot, the system appears to get through the boot stage OK. It also proceeds to start up the OS OK, but then services fail to start. Further action stops temporarily, but pressing the escape key or a function key makes the screen go black for a second or so, returning with what's shown in the last image. No other keys have any ef…
-
Reputation Points
- 6 replies
- 4.4k views
- 3 followers
-
-
I have flashed the last 23.8 bookworm lite image to my lepotato 1GB model, and it launched with 927 MB total memory. running apt update ; apt upgrade ; reboot it drops to 862M How can I reclaim the remaining memory? This is mostly a headless server i do not need any GPU. just basic hdmi output for troubleshooting purposes. before: Welcome to Armbian 23.8.1 Bookworm with Linux 6.1.50-current-meson64 System load: 8% Up time: 4 min Memory usage: 13% of 927M IP: CPU temp: 48°C Usage of /: 4% of 29G After: Welcome to Armbian 24.2.1 Bookworm with Linux 6.6.16-current-m…
-
System Overview Hardware: ODROID HC4 OS: Armbian (current version) Kernel: 6.12.44-current-meson64 Use case: Production NAS with critical data Problem Description During apt upgrade, the following critical warnings appear: dpkg: warning: This system uses merged-usr-via-aliased-dirs, going behind dpkg's dpkg: warning: back, breaking its core assumptions. This can cause silent file dpkg: warning: overwrites and disappearances System state analysis reveals: /bin, /sbin, /lib are correct symlinks to /usr/* BUT: Files exist in duplicate (/bin/bash and /usr/bin/bash identical) DKMS cannot build kernel modules (missing headers)…
-
Hi. Looking for help. I have uploaded Armbian v6.12 Desktop Ubuntu to a card and run on my device. You can see in the screenshot (video of the boot here: https://drive.google.com/file/d/1_1dm1rP33tbYISPUsta7nZV1eKPy3Plq/view?usp=drive_link) that some rubbish is displayed. I would also add that the device is sending a signal that is only displayed by the TV. No other monitor in the house is able to display anything that is sent from the device. This is even stranger, as when I upload the old ubuntu 18.04 to the same card, the device connected under any display displays my desktop. Any suggestions or suggestions? Maybe an older version? I want to make myself a RetroPi …
-
Reputation Points
- 10 replies
- 2.4k views
- 1 follower
-
-
Hi, I installed/compiled different browsers that are based on QT (QtWebKit, QtWebEngine). Unfortunately, special characters, often necessary for typing in non-English languages, do not work. E.g. a Spanish accented 'e appears as 00e9 This makes all these really fast browsers with low memory footprint useless for multilanguage writing (e.g. in webmailers). The characters work fine in the terminal and other browsers such as Midori, Firefox and Chromium. Thus, I think, something went wrong in the compilation of QT libraries. Any idea how to solve that?
-
Currently no /dev/watchdog device on N2 with -current and -dev armbian kkernel. But watchdog present in -legacy. I see meson-wdt kernel module present on image, I transplant meson_wdt segment from dts file of legacy kernel to dev and current. diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts index 819afc748828..18990208f269 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts @@ -226,6 +226,20 @@ hdmi_connector_in: endpoint { }; }; }; + + wdt: watchdog@0xffd0f0d0 { + compatible = "amlogic, meson-wdt"…
-
Reputation Points
- 2 replies
- 4.1k views
- 1 follower
-
-
I tried three way for hiding mouse, but not work: 1. Unclutter: ``` unclutter -idle 0 -root -display :0 `` It shows unclutter: could not open display 2. startx -nocursor -> not work 3. Using xbanish and boot from Systemd: ``` ~/.config/systemd/user/xbanish.service ``` [Unit] Description=xbanish After=default.target [Service] Type=simple ExecStart=/usr/bin/xbanish Restart=on-failure StartLimitBurst=10 RestartSec=30 [Install] WantedBy=default.target Is there any good way for hiding mouse on XFCE4 desktop (Armbian) ? Thanks
-
Hi all, I'm a bit lost to find the root cause so I share all what I noticed Installed - I'm using Armbian_21.02.4_Odroidn2_buster_current_5.10.27.img image on a eMMC 64Gb on an Odroid N2+ board - I installed docker and have two containers activated from portainer/portainer-ce and linuxserver/plex images - I installed exFat-fuse and exFat-utils to be able to mount an external exFat drive connected via USB Issues - Right after booting, the USB drive is mounted but is not seen by Plex. Restarting the plex container make the trick but I have to do it each time - After some time, the mounting point is not anymore accessible and give me the ' Transport en…
-
Reputation Points
- 2 replies
- 4.1k views
- 1 follower
-
-
I'm using odroidc2 installed with Armbian 24.11.1 Noble Gnome to an eMMC card After the OS installation, power cycled and it went through the process of configuring the root password and initial user account. All was successful. However, once the system shows the greeter screen, the system is frozen. It does not respond to keystrokes nor mouse movement. The blue light on the odroidc2 continues to flash. I also used the USB/UART module to see the start up messages and to login. When the boot process is complete it prompts for user login but it does not accept any keystrokes. The serial port output is attached wtminicom.log
-
Reputation Points
- 0 replies
- 2.8k views
- 1 follower
-
-
Been using the Lepotato with Armbian fine for a few weeks. Typically accessing via ssh over the network, suddenly after a reboot, it's not appearing on my network, solid red light, solid green light, and a blue heartbeat as well as the NIC light blinking as if network connection is functioning normally, but my network is not assigning an IP address and the potato isnt sending any packets. What might the problem be here? HDMI shows no output, using Armbian Jammy made for the tato.
-
Reputation Points
- 2 replies
- 3.9k views
- 1 follower
-
-
Hello! I have installed Armbian Bookworm on Khadas VIM3. Also I have enabled "UARTa" , "UARTc" in armbian-config utility. After reboot in file /boot/armbienEnv.txt I have checked options about uart (uarc). Also there are many files /dev/ttyS[0-7] exists. After this I try to connect "minicom -D /dev/ttyS0" (ttyS0, S1, and S3 etc). But no answer from my device on pins 15,16 OR 18,19 (this is a UARTA,UARTC, UART linux). Python sripts pyserial output: "i/o error". Does Armbian (Bookworm or Jammy) supports Khadas VIM3 UART? Are there successful cases? One more question: On Ubuntu Server files …
-
Reputation Points
- 1 reply
- 2.7k views
- 1 follower
-
-
I have just installed an Armbian Jammy CLI on my BPI-CM4. I need to use the UART that is routed to pins 8 and 10 on the 40-pin connector (UART_EE_B in the BPI-CM4 schematics). I have enabled it in the device tree by changing this from disabled to okay: serial@23000 { compatible = "amlogic,meson-g12a-uart\0amlogic,meson-gx-uart"; reg = <0x00 0x23000 0x00 0x18>; interrupts = <0x00 0x4b 0x01>; clocks = <0x12 0x02 0x2a 0x12>; clock-names = "xtal\0pclk\0baud"; status = "okay"; phandle = <0x12b>; }; Once rebooted, and new UART appears (ttyAML6). However, it does not work. What am I missing? …
-
Reputation Points
- 1 reply
- 2.8k views
- 1 follower
-
-
Hello, After a firmware update today I got a problem with Wireguard on my Odroid-hc4. I got that when checking ufw status, sudo ufw status verbose ERROR: problem running iptables: modprobe: FATAL: Module ip_tables not found in directory /lib/modules/5.10.123-meson64 iptables v1.8.7 (legacy): can't initialize iptables table `filter': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How to fix that? Laurent
-
Reputation Points
- 11 replies
- 11.6k views
-
-
I am wondering how to install this. I've installed armbian on a nanopc, and edge V which is now a brick after a brief use as an armbian machine. But never successfully to a vim 3. I have a fresh out of the box vim3 that fails on boot with the current image on sdcard. The first vim4 was a doorstop on arrival. I finally have a second vim 4 that does seem to work if I push the function button 3 times it goes to oowow. But so far nothing that I've read works to boot from sdcard. "Holding the function button while power on." I havent found any instructions here about an install process other than insert th…
-
I've been trying this all day and I can't get it to work for me (focal mainline kernel 5.6.y) - I can start on sdd, change hostname, make it a static ip, reboot - works fine. As soon as I try to nand-sata-install and boot from sdd + system on usb it just disappears after the reboot. Pity, works fine with the legacy.
-
I am trying to use the s905x on the Le Potato board to encode a 1080p video to stream via RTSP. Using software, the video is encoded anywhere in between the 5-7fps range. I want to use the hardware encoder that is available on the chip but I haven't been able to find any libraries that let me use the hardware on this specific board. I have tried installing the Mali-450 GPU drivers here (https://wiki.debian.org/MaliGraphics) but no luck.
-
Hello, Setup Yocto branch: Kirkstone (honister back-ports disabled) Layers / commits meta-odroid 06f8d2c (last week’s master) poky kirkstone (bitbake 2.2.0) Kernel: linux = v5.15 What I changed so far Enabled the driver Added a linux-hardkernel_%.bbappend with: CONFIG_PWM=y CONFIG_PWM_MESON=y Patched the Device Tree (added a new layer to patch in yocto using devtool): From 9f296f4b8f636b12ef8c0a4720cf0d25d9eeb810 Mon Sep 17 00:00:00 2001 From: OpenEmbedded <oe.patch@oe> Date: Thu, 17 Jul 2025 15:50:18 -0400 Subject: [PATCH] some changes to source for pwm --- arch/arm64/…
-
I recently upgraded from an Odroid HC2 to and Odroid HC4. I reinstalled the OS following the instructions on armbian.com, flashing onto a MicroSD. After migrating the apps (mostly dockers), I found that restic (backup tool) was generating out of memory errors and bringing the system to a halt in a way the HC2 didn't. This surprised me as it's overall higher specced, and the configuration was otherwise identical. After some troubleshooting, I realised there was no swap drive specified, and that creating a swap eliminated my out of memory errors. I'm not sure if the source of the "problem" is the swapfile here, but it at least…
-
I've just installed Armbian Bookworm with the XFCE desktop on my Le Potato. Everything on the screen is larger than it should be so I checked the screen resolution in Settings->Display and it reports 1920x1080. However, when I go to screenresolutiontext.com it says I am at 960x540. What can I do to correct this? Thanks, Rich
-
Reputation Points
- 0 replies
- 2k views
- 1 follower
-
-
Been having an issue where my idle temps are >60C The fan will spin for maybe a second or two and then turn off for 10-20 seconds Checking /sys/class/hwmon/hwmon2/pwm1 and it is set to 0 even though my MINPWM is set to 90 Even if I manually tee 90 to pwm1 it will eventually reset to 0 even with fancontrol turned off So something resetting without my input... fan1_input does read fan speed & pwm1_enabled is set to 1 lsof & auditd do not have any info as to what is overwriting the file Only way I can get the fan to stay on is to loop the tee command for a few seconds and then it is on that one speed Turning f…
-
Reputation Points
- 4 replies
- 6.1k views
- 2 followers
-
-
Hello! I have installed on Armbian 24.8.1 noble (ubuntu 24.04) . Also I have enabled "UARTa" , "UARTc" in armbian-config utility. In /boot/armbianEnv.txt file: overlays=uartA uartC for enable UART port. There are many files /dev/ttyS[0-7] exists. After this I try connected to this ports, but no success (minicom -D /dev/ttySx). Python sripts with pyserial module output: "i/o error". The same problem I have noticed with previous versions of Armbian. I have checked on other distributive (Khadas version of ubuntu server) the uart port is worked fine. Does Armbia…
-
Reputation Points
- 2 replies
- 3.6k views
- 1 follower
-
-
Hello All, Have a question, I see there is an option to use eMMC with the Le Potato aml-s905x-cc 1gb (which I got running yesterday), but what eMMC modules actually work with this board (I'm using a MicroSD card on my board at the moment)? Perhaps there should be a thread for Le Potato Hardware Options (just a thought)
-
Hi! You can find the armbianmonitor output attached to this thread. The issue is: when I use HDMI audio output with wine applications the entire system freezes very soon, usually after some seconds from the launch of the application. Some fraction of the latest played sound keeps looping very fast and both mouse and keyboard are unresponsive. All I can do is to unplug the power. This happens both on Odroid N2 and Odroid N2+. Everything works fine if I use some bluetooth headphones. And everything works fine if I use HDMI audio output with linux native applications. The problem is in the combination of Wine applications and HDMI audio output. Armbian Monitor Out…
-
Hello, after upgrading the Odroid C2 to the current Version on 16.08.2024 the USB-devices do not work at all. According to the diagnosis information they are recognized during during bootup. But later they are disconnected for an unknown reason. https://paste.armbian.com/jucovipaxo lsusb only lists two devices: Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub The suggested hack "usbcore.autosuspend=-1" for USB-problems is already activated, but USB doesn't work anyway Maybe there is a solution for this strange behavior of my C2.
-
I'm testing the Armbian image for Odroid N2+ ( Armbian_22.08.7_Odroidn2_jammy_current_5.19.17_xfce_desktop) to see if it's a good migration path from the HardKernel base image. Unfortunately I need to get both i2c bus running on the GPIO and so far only the first bus seems to work (i2c-0). Looking into /sys/bus/i2c/devices , it looks like i2c-1 is tied to the hdmi port instead of the 2nd i2c bus on the GPIO : lrwxrwxrwx 1 root root 0 Dec 31 1969 0-0051 -> ../../../devices/platform/soc/ffd00000.bus/ffd1c000.i2c/i2c-0/0-0051 lrwxrwxrwx 1 root root 0 Dec 31 1969 i2c-0 -> ../../../devices/platform/soc/ffd00000.bus/ffd1c000.i2c/i2c-0 lrwxrwxrwx 1 root …
-
Reputation Points
- 4 replies
- 5.6k views
- 1 follower
-
-
Hello, i need to activate the serial port on the odroid N2-plus, the serial port is on pins (J2 - 2x20 PINS) 8/10. Usually this uart with ubuntu is at /dev/ttyS1. If I try to use it on armbian I get an input/output error. I read the following post, I understand that it is not implemented yet. Can anyone point me in the direction of trying to do this?
-
Reputation Points
- 8 replies
- 6.3k views
- 1 follower
-
-
Whatever I plug into the usb otg port, it doesn't get recognised. I think the port got disabled. What happened? I connected a new harddrive via usb3 but the machine wouldn't boot because of some "Unexpected XHCI event". I had to add a usbstoragequirks to u-boot env. (via armbian-config) to solve that, but now the usb otg port is no longer working. Googled a lot and found one possible solution but it did not work for me ( https://forum.banana-pi.org/t/topic/5485/13 ). https://paste.armbian.com/aqowuxukev
-
I have a Banana Pi CM4 + CM4 IO Board - literally the same one pictured in https://www.armbian.com/bananapicm4io/ I downloaded and installed Ubuntu 24.04 (Noble) Server Image - "Armbian_24.8.1_Bananapicm4io_noble_current_6.6.47.img" For convenience, I installed the image to an SD card. Armbianmonitor link: https://paste.armbian.com/igahozatow Everything boots and I can use armbian-config to connect to my local WiFi network, but the speeds are really really slow: iperf3 gives me ~40mbps pretty consistently: -------------------- [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 51.1 MBytes …
-
Hi, first post here. After upgrading Armbian on my Odroid-N2 to 5.8.13-meson64, I can no longer mount using autofs, neither manually nor via systemctl. The error message is: mount: /home/<mountdir>: unknown filesystem type 'aufs'. The Armbian Build Options information suggests that kernel builds include AUFS by default: AUFS ( yes | no ): Include support for AUFS Am I missing something? Armbian version is #20.08.6 SMP PREEMPT Thu Oct 1 18:51:27 CEST 2020
-
TL;DR Where in armbian build system correctly can be make N2-only related changes: 1. /boot ext4 volume have to have symlink . as boot, can be created with command ln -s ./ boot 2. kernel env variable set in boot.ini contain part but it shouldn't. This substring need to be removed if btrfs choosen. 3. /boot ext4 partition have only 4 MB free. I am not sure but think it's too small; for example there no space to run update-initramfs -u. I think it should be larger, like 500 MB. Long: I want to run my oDroid-N2 with root on BTRFS filesystem. I use manual on armbian image build and did time ./compile.sh BOARD=odroidn2 BRANCH=cur…
-
Reputation Points
- 0 replies
- 3.6k views
- 1 follower
-
-
I have two Odroid C2s. One I have been using as NUT server for Eaton UPS. Today NUT clients report no connection. What seems to be the problem is the C2 (this happens with both, same SD card) are not seeing devices plugged into USB ports so the USB connection to the UPS is not working. I have verified the Eaton and USB cable are fine. I regularly update the C2 I wonder if a recent update has affected the USB port functioning? Any way to troubleshoot? I tried a few USB flash drives and then lsusb but none are seen.
-
Reputation Points
- 1 reply
- 2.5k views
-
-
Hello community, I'm a beginner with all that kernel and modules stuff, so please be kind, if I am asking stupid questions. My plan is to install a Hifi-Shield on my C2, but so far had no luck: modprobe: FATAL: Module snd_soc_pcm512x not found in directory /lib/modules/ Found out, that some modules are present under /lib... e.g. /lib/modules/5.15.0-105-generic/kernel/sound/soc/codecs/snd-soc-pcm512x.ko (cave:this is example from my ubuntu I'm writing on) some other modules are in fact missing. I found similar modules here: https://github.com/3isenHeiM/HiFi-Shield-Plus/blob/master/sound/soc/aml/m8/snd-soc-odroid-dac.ko …
-
Using kernel 4.14.65, I get a usb-driver crash when accessing the top left port (topmost, nearest the ethernet port) of the Le potato. Plugging any device into this port results in the following kernel message and prevents the use of usb until reboot. There is no kernel stacktrace. As long as I don't plug anything into that port, the other 3 ports on the board work fine. [ 292.242434] usb 1-2: new full-speed USB device number 7 using xhci-hcd [ 302.562341] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command. [ 302.583217] xhci-hcd xhci-hcd.0.auto: Host halt failed, -110 [ 302.583231] xhci-hcd xhci-hcd.0.auto: xHCI host controller not …
-
Reputation Points
- 6 replies
- 6.8k views
- 1 follower
-
-
I was trying Jammy (autobuild) with kerenl 5.15.18 on Khadas Vim3 4GB RAM, but is does not start, no HDMI output, no LED activity. Then I tried Hirsute with kerenl 5.13 and that boots fine, but after update new kernel (5.15) and also u-boot is installed and then it does not start again. My solution for now is to boot Hirsute with 5.13 and replace all edge packages with current (linux-dtb-current-meson64, linux-image-current-meson64, and linux-u-boot-khadas-vim3-current). This downgrades the kernel to 5.10.81, but the board can be updated and boots fine.
-
Reputation Points
- 6 replies
- 5.3k views
- 3 followers
-
-
Odroid-N2 using Armbian_20.08.1_Odroidn2_focal_current_5.8.5 I've recently got a "Connection timed out" issue. For instance, I can open files with nano, use htop, armbian-config, update and upgrade packages, but I can't reboot (everything over ssh). I'm having a feeling that the issue started when I tried to figure out if it's possible to get HDMI to work with my 4K TV when the HDMI cable is not plugged in at boot. In that case, I booted several times and chaged boot.ini with setenv display_autodetect "false", setenv hdmimode "1080p60hz" and setenv disablehpd "true" without success. armbianmonitor -u information is attached at the end in my post where this line migh…
-
Reputation Points
- 7 replies
- 6.2k views
-
-
Introduction: I used Armbian Imager to flash Armbian 26.8.1 XFCE onto my Le Potato AML-S905X-CC-V1.0-A. Problem: On boot of the Le Potato, I could see the setup text via HDMI output on my monitor. But after setup was complete, the HDMI output would stop and my monitor would go to sleep. There was no longer HDMI output after initial boot. Solution: So I needed to SSH in over ethernet and run these commands to resolve this issue: echo "blacklist simpledrm" | sudo tee /etc/modprobe.d/blacklist-simpledrm.conf sudo update-initramfs -u sudo reboot This fixed my HDMI output issue and I can use my Le Potato b…
-
Reputation Points
- 0 replies
- 379 views
-
-
$ stress -c 1 -t 60 & [1] 2578 $ sudo chrt -r -p 95 2578 chrt: failed to set pid 2578's policy: Operation not permitted Why this doesn't work? My actual problem is that Jack Audio can't use real-time scheduling, but this example should demonstrate that there is a general problem probably. (getting ERROR: Cannot use real-time scheduling (RR/10) (1: Operation not permitted), ERROR: AcquireSelfRealTime error) $ uname -a Linux odroidc2 6.6.16-current-meson64 #1 SMP PREEMPT Mon Feb 5 20:14:39 UTC 2024 aarch64 GNU/Linux $ lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Armbian 24.2.1 bookworm Release: 12 Codename: …
-
Reputation Points
- 1 reply
- 4k views
- 1 follower
-
-
I would like to use the mmc commands available in uboot on this board. I am able to boot properly in this mode and "help" properly lists all the commands available in this mode. On my board Armbian is running in EMMC. When I invoke "mmc" or the "mmcinfo" commands the system replies with the following error: Card did not respond to voltage select If I insert an Sdcard in the slot these two commands do respond properly which implies that uboot is seeing the Sdcard as default. Is there a way to redirect these commands to the EMMC? Regards
-
(Sorry this tagged as C2 since C4 tag not available) - Not trying to ruffle any feathers mentioning dietpi. I have an Odroid C4 with petitboot on sd for booting os's. I have a couple usb3>sata cases with 120g ssd's installed. Blazing fast and about $25usd 🙂 I can then download images and write them to the drives. Dietpi 9.11 and using the netboot function builtin to petiboot a few different flavors of other os's including debian 12. I have Armbian on SD as well. My problem is that it is incredibly slow running from sd on my c4. It runs VERY WELL though and detects audio properly on my tv through hdmi (shows as unknown display). W…
-
Reputation Points
- 2 replies
- 3.5k views
- 1 follower
-
-
Checksum not matching for images for odroid n2 for these: Focalstable5.10.ySHA ASC278MApr 4 2021 Focal xfce desktopstable5.10.ySHA ASC802MApr 4 2021 Also after installing images they would crash.
-
I have a Logitech C920 webcam I am trying to use on my Radxa Zero. I'm running Armbian 23.11.1 Bookworm 6.1.63 64-bit. When I run v4l2-ctl -i /dev/video1 --list-formats to query the webcam, it errors out. VIDIOC_S_INPUT: failed: Inappropriate ioctl for device ioctl: VIDIOC_ENUM_FMT Type: Video Capture Multiplanar [0]: 'NM12' (Y/UV 4:2:0 (N-C)) It seems anything relying on v4l2 is also failing to work. Anyone have ideas of what the issue may be? Thanks! ---------------------- FYI...If I use this webcam on a RaspberryPi 4 running Bookworm, it produces the following output a…
-
Reputation Points
- 0 replies
- 2.7k views
- 1 follower
-
-
Output of armbianmonitor -u: http://ix.io/2SDQ The latest released 21.02.3 Lepotato buster 5.10.21 with Xfce preinstalled is unable to start a desktop environment from a fresh image install. After booting up, the display goes to a black screen with a blinking cursor. Initial issue seems to be lightdm failing to start w@lepotato:~$ journalctl -u lightdm.service -- Logs begin at Sat 2021-03-13 05:51:27 UTC, end at Sat 2021-03-13 06:06:57 UTC. -- Mar 13 05:51:33 lepotato systemd[1]: Starting Light Display Manager... Mar 13 05:51:33 lepotato lightdm[2457]: Could not enumerate user data directory /var/lib/lightdm/data: Error open…
-
I can not reiterate enough just how easy it is to "clone" your modified emmc, or microSD card OS, ... into an image file that you can easily restore with (balena)Ethcher afterwards, and all withiin Linux. 1:/ you'll need a USB-card-reader-adapter. 2:/ no matter how your USB-reader card reader sees your emmc, microSD card, ..., it'll most likely be mounted on a /dev/sda1 partition. 3:/ sudo dd bs=4M if=/dev/sda of=~/tmp/armbian_odroidc4_11_01_2025.img (you don't dd the partition, you dd the drive). 4:/ (optionally) sudo xz -v armbian_odroidc4_11_01_2025.img (this will take some time). ...and that's it, ... and you know the rest.
-
Reputation Points
- 6 replies
- 6.9k views
- 1 follower
-
-
my C2 did not boot after upgrading from 6.6.63-current-meson64 to 6.12.17. I also tested kernel 6.12.13 from debian minimal image, same problem: Applying kernel provided DT fixup script (meson-fixup.scr) ## Executing script at 32000000 ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 17076402 Bytes = 16.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 04080000 Booting using the fdt blob at 0x4080000 Loading Ramdisk to 7af01000, end 7bf4a0b2 ... OK Loading Device Tree…
-
Reputation Points
- 5 replies
- 5.4k views
-
-
I was going to install armbian on a new vim 3 board but it seems that krescue no longer exists. Is there another way to install armbian to a vim 3? Does the vim 4 have the same problem?
-
Reputation Points
- 11 replies
- 6.5k views
- 1 follower
-
-
So Le Potato (and Sweet potato) take about 10 seconds before reaching systemd. Is there a way to speed this up? I've tried putting boot_delay=0 as well as console=serial in armbianEnv.txt in hope of shortening the time in u-boot, but these didn't change anything. I've also tried building this image with no initramfs and no loadable module support.
-
Reputation Points
- 9 replies
- 5.8k views
- 1 follower
-
-
Added more details for original post odroidc2 with Armbian 23.02 Jammy XFCE (Armbian_23.02.1_Odroidc2_jammy_current_6.1.14_xfce_desktop.img) I have an odroidc2 connected to: 1)monitor with built-in speakers via hdmi cable. 2)usb audio adapter (https://ameridroid.com/products/usb-audio-adapter) 3)ethernet cable 4)wireless keyboard dongle I have issue outputting audio to monitor speaker. dmesg and syslog output related to hdmi is as follows. Any help is greatly appreciated. Thanks $ dmesg|grep hdmi [ 0.035220] platform c883a000.hdmi-tx: Fixing up cyclic dependency with d0100000.vpu [ 0.037586] p…
-
Reputation Points
- 0 replies
- 2.5k views
- 1 follower
-
-
Hello everyone, I am trying to get a Bigtreetech PiTFT70 DSI screen working on my Banana Pi CM4 mounted on a Bigtreetech Manta M8P 3D printer control board. It is supposedly a clone of the Raspberry Pi 7inch DSI display and uses the same display and touch chips. The DSI port on the M8P is wired to DSI 1 port on the Bpi CM4. I have tried hacking together a device tree overlay for it but I don't know enough of what needs turning on and what addresses they require (i2c etc) to get it working. Can anyone with Amlogic meson knowledge assist me? I am running the latest armbian bookworm 23.8 with all current updates installed.
-
Sometimes when reboot device goes to emergency mode and you can not connect to it remotelly. I read on internet, may be here, that make this [Firmware Bug]. I downgrade Kernel to "Igor" recommended 5.7.15 and there the [Firmware Bug] missing. I tested new and newest Kernel via armbian-config but the [Firmware Bug] is present everywhere. Kernel 5.7.15 seems good without this bug but i have no sounds on Audio out or via HDMI. --- journalctl -xb [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader!
-
I am wondering if the ts1050 or some other embedded screen is working with the vim4 at this time?
-
Reputation Points
- 6 replies
- 3.6k views
- 1 follower
-
-
PRETTY_NAME="Armbian 22.08.7 Bullseye" NAME="Debian GNU/Linux" VERSION_ID="11" VERSION="11 (bullseye)" VERSION_CODENAME=bullseye ID=debian HOME_URL="https://www.debian.org/" SUPPORT_URL="https://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/" Hello everyone and thanks for accepting me in the forum. I recently bought a banana pi M5, intalled armbian but i can't use i2c, I tried to enable i2cA and i2cB from armbian-config without success. I have also tested numerous dts files with no success. Can anyone help me with this? Thank you.
-
Reputation Points
- 10 replies
- 8.6k views
- 1 follower
-
-
Used HW and SW: Odroid N2+ 4GB with 32 GB eMMC Sandisk 32 GB SD card SW: Armbian_25.5.1_Odroidn2_bookworm_current_6.12.28_minimal.img If I write the image to the SD card (using Balena Etcher), the system boots up and works fine. If I write the image in the same way to the eMMC using an adapter (with Balena Etcher), the system does not boot – only the red LED stays on. Booting via SD card with system and boot files transferred to eMMC using armbian-install also doesn't work. The system fails to boot again. The switch on the N2+ is in the correct position. The eMMC module is functional – if I write CoreELEC or Android images to i…
-
Hello, I have a La Frite 1gb. Im trying to boot armbian but it wont boot, I have checked the common problems list on the libre computer forum , It stated sd card, power supply etc. I have made sure that none of these are the problem, I have tried 5 different sd cards and im now using a 6th brand new Sandisk Extreme bought in the store (The one recommended by libre computer). I have tried many PSUs , All 5V 3.0A which is supposed to be enough, I get no help in the la frite forum so i thought i would check in with you guys and see if anyone knows what the issue could be. Also, id like to add, it wont boot anything, none of the images of ubuntu destkop, raspbian, etc f…
-
I have a Odroid C2 that was being used as a TV box with Coreelec, and has now been retired due to upgrade. I want to repurpose the C2 for a completely different role, so I am trying to install Armbian in it. I downloaded the Armbian image from here and followed the official install instructions, but the C2 refuses to boot. The red light turns on when powered but nothing more happens, no other lights, no screen, nothing. Coreelec was booting with no issue, so it must be something I'm setting wrong. Just in case I tried a different SD card and two different images, Bookworm minimal (the one I'm interested in) and Ubuntu Noble XFCE (just to test). Sam…
-
Reputation Points
- 2 replies
- 3.2k views
- 1 follower
-
-
FYI, Device is Odroid N2+ 4 GB. Some months ago I installed/ran: Armbian_25.2.1_Odroidn2_bookworm_current_6.12.13_xfce_desktop.img with no issues that I could not overcome. I re-downloaded it yesterday and re-installed/ran it on another Odroid N2+ 4GB with no issues. However when I try to install/run: Armbian_25.11.1_Odroidn2_noble_current_6.12.58_xfce_desktop.img "* Desktops are very simple and minimal but containing standard features such as Chromium, Firefox browser, Office tools etc." It leads to a number of issues, but the most important one is no internet browsers are installed that are either visible from the Applica…
-
Hi I was using: Title: Armbian 21.08.5 Odroidhc4 Debian buster legacy Then something bad pushed me to run apt update/upgrade No ZFS anymore. Installed 22.08.2, but, when tried to install kernel headers using armbian-config, result: "grep: invalid max count" message. What is the current correct way to install Armbian with ZFS? Thanks ChrisO
-
Reputation Points
- 5 replies
- 4.6k views
- 1 follower
-
-
Hi everybody, I just got a hand on a generic tv box powered by 4 cores S905x. Performance from this tv box is not satisfied for me. So I am thinking about this VIM4. Can anyone please tell me how is single core and multi cores cpu performance on VIM4 vs S905x? How much faster is it?
-
Reputation Points
- 0 replies
- 2.7k views
- 1 follower
-
-
Is it possible to enable the I2S service (for audio) on BananaPim2pro? In the program configuration: armbian-config / manage device tree overlays...there are no entries for: I2S. Maybe someone already knows what to enter or how to enable it 🙂
-
root@odroidn2:~# journalctl -x | grep haveged Mar 12 19:43:51 odroidn2 kernel: audit: type=1400 audit(1615574627.248:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/haveged" pid=1635 comm="apparmor_parser" Mar 12 19:43:47 odroidn2 audit[1635]: AVC apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/haveged" pid=1635 comm="apparmor_parser" -- Subject: A start job for unit haveged.service has finished successfully -- A start job for unit haveged.service has finished successfully. Mar 12 19:43:52 odroidn2 haveged[1836]: haveged: Couldn't initialize HAVEGE rng 9 Mar 12 19:43:52 odroidn2 haveged[1836]:…
-
Reputation Points
- 6 replies
- 8.8k views
- 3 followers
-
-
Hi Everyone, I'm trying to get audio out of my N2+ via SPDIF on the 7 pin header, or any gpio pin if necessary. So far I have confined my SPDIF output works with the official Odroid MATE image, and also that I can get audio out via the 3.5mm jack on armbian after flowing this post . I have tried to understand the amixer wizardry but no luck achieving anything so am a bit stuck as I would really like to use armbian over the Odroid image. Thanks for any help!
-
Good morning, after some time using armbian on my OdroidN2 with great success (got Nextcloud with working Talk installed, external USB, Minecraft server, nginx, LetsEncrypt, Netdata...) I encountered some problems I am not able to solve by myself: I bought a RTC battery and a LED power button to "finalize" my Odroid (hardwarewise), and to my surprise both did not work as expected. RTC: It says: chris@OdroidN2:~$ sudo hwclock hwclock: select() to /dev/rtc0 to wait for clock tick timed out cat /proc/interrupts |grep rtc ...gives me also no return (empty string), so i guess there is a module missing in the kernel : chris@Odroi…
-
Reputation Points
- 11 replies
- 9.8k views
- 3 followers
-
-
After performing a warm reboot the system fails to start. Get error message boot device not found. Power cycling fixes the issue. Using Armbian 25.8.1 image that is available for download (minimal trixie). Board is a LibreCompter Sweet Potato. Thanks,
-
I prefer Debian to Ubuntu. Is there a possibility the VIM3 version will run on the VIM4 (doubtful)? Is anyone currently working of Debian Bulleye support for the VIM4, or interested in befinning a port? Larry
-
Today we got working UART A, so I decided to wire up a cheap DCF77 receiver to it. On a first test I got spammed with libre-computer-board ntpd[1518]: parse: convert_rawdcf: start bit / parity check FAILED for "###############RADMLS1248124P124812P1248121241248112481248P??" This was solved with the following kernel patch: diff -Nru libretech-linux.old/drivers/tty/serial/meson_uart.c libretech-linux/drivers/tty/serial/meson_uart.c --- libretech-linux.old/drivers/tty/serial/meson_uart.c 2017-10-24 19:49:30.776000382 +0200 +++ libretech-linux/drivers/tty/serial/meson_uart.c 2017-10-24 19:52:39.660000472 +0200 @@ -362,7 +362,7 @@ writel(val, port->membase + A…
-
Khadas VIM1S is an upcoming low-profile single board computer powered by an Amlogic S905Y4 quad-core Cortex-A35 processor that’s meant to provide an upgrade to the Amlogic S905X-powered Khadas VIM SBC introduced in 2016, and since then renamed to Khadas VIM1. Khadas has been teasing two new SBCs: the low-end Khadas VIM1S with S905Y4 SoC, and the most powerful Khadas Edge2 board equipped with a Rockchip RK3588S octa-core Cortex-A76/A55 processor. I have received both as you can clearly see from the photo above :), but I’m only allowed to write about information available publicly at this time, so today I’ll introduce the Khadas VIM1S which looks just like the VIM1 board. K…
.thumb.jpg.d12ff4661cda8bcd4c6c766fa549b1b9.jpg)
