Orange Pi 5

I thought it would be easy, but I am now turning in circles, so I am asking here. I have a working system booting on NVME (when no SD card inserted), with two partitions nvme0p1 (256Mb) and nvmeop2 (40Gb) I would like to clone my working system on a SD card. How shall I proceed? I am not asking details instruction, only the rough path I should follow (e.g. dd partitions, tune2fs ......). PS: I thought it would be easy, but whatever I do, the system keep taking /boot on the nvmeop1, so I really struggle to boot on the /boot of the SD card

Hello. Is it possible to enable OV13855 camera on OPi5 with the latest armbian image? If yes, how do it? Thanks!

i am taping in the dark here and in need of some help. i am running openhab on armbian 23.8.1 server and i need to get audio out on 3.5 jack for alerts. openhab has only two options system speaker and web audio. web audio plays on client like browsers using pulse audio. But if i use system speaker nothing comes out. What can i do to get sound on 3.5mm out on opi? is it even possible? i have this but this is also where my knowlege ends so help needed. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: rockchipdp0 [rockchip-dp0], device 0: rockchip-dp0 spdif-hifi-0 [rockchip-dp0 spdif-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card…

Hi, I would like to use my usb wifi adapter from my old Raspi 3. `lsusb` shows: `Bus 007 Device 002: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter` `ip a` shows: ``` 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 76:ac:9a:1c:50:76 brd ff:ff:ff:ff:ff:…

Hello, I'm planning on running a k3s cluster with Rook storage with a few of the Orange Pi 5 that I got. A prerequisite for rook however is RBD module. I've been able to recompile the kernel including RBD support, however I've been unable to get the device to boot from the new kernel. Rebooting after kernel has been built and installed still reports Linux 5.10.110-rockchip-rk3588. Any help would be appreciated. I've since wiped the boxes clean and have a fresh install booting from SSD with the OS installed on the NVMe attached so I will be able to provide any information required. Thanks!

I am trying to build the kernel with the standards scripts, but directly on my orange pi 5. The build is stopping at some point because of a Warning issued by the compiler (this is the default behaviour for the compiler who does not tolerate any warning by default). (Some functions in the C code are depreciated, thus a warning is issue) How can I set the CFLAGS so that the kernel build takes it into account during compilation? Thanks.

Hi, I have orange pi 5. I searched all over internet for information how to set on startup/power on GPIO pins behavior, but i cannot find anything. Most of GPIO pins are set to IN mode 1. Sadly I need them to output mode 1. I am scared something could burn this way since i set them to though wiringPI after kernel boot sequence is complete. Can some one give information how I can set them up at earlier point when I power on the board? I found that DTB/DTS file could do it. But there is no clear information / pin addresses I should set. Thanks in advance! Regards!

Hi, The release notes for Armbian 23.11 state, under Key Improvements in This Release, "Mainline Kernel for RK3588 with experimental HDMI support." I am currently running the default 5.10.160-legacy-rk35xx kernel If I wanted to switch to and try out the mainline kernel for RK3588 with experimental HDMI support, would I do something like this: sudo apt install linux-image-collabora-rockchip-rk3588 After testing, If I want to rollback to the default legacy kernel, what are the steps involved? Apologies if there are instructions elsewhere that cover this. Thanks in advance for any guidance.

I download the following image and encountered serious problem; Armbian_23.8.1_Orangepi5_bookworm_legacy_5.10.160_cinnamon_desktop.img.xz The problem is that after screen blank out, 8 CPU cores get near full 100% usage and OPi5 gets very hot. They all have the following htop profile. Pri NI VIRT SHR S CPU% Command 20 0 5725M 224M R 96% cinnamon -- replace

I could not find any arm64/aarch64 MODERN, up to date, Tor browser binaries. Anything below current-stable would be considered insecure, and at a glance I couldn't find them anywhere. So I was able to compile Nightly for the latest updates as well It took 331 minutes, and failed 4 times along the way with 8GB RAM native on the device and 4GB ZFS to start. It did a SIGKILL9 on firefox-glean. Increased to 8gb, still failed until I increased ZFS to 16gb, and then even at a whopping 16gb it crashed next on GkRust for OOM/SIGKILL9 as well until increased ZFS to 32GB! 331 minutes later, it was succesful Just wondering, to save myself from future pun…

Hi there, Just got Orange Pi 5 8GB and have no idea where to begin. I have a microSD card available, but no writer. I had the idea to boot from USB thumbstick and then write the SD card using the port on the Orange Pi 5, then I can boot from SD card. Is this possible? What image and method do I need to follow in order to boot from a simple 32GB USB Sandisk thumbstick? Thank you!

I want to install Armbian on Nvme SSD. How do I install on SSD?

I need to move my homeassistant from rpi4 to an opi5 but I have some I2C sensors connected. Had anyone any luck configuring python and gpio to work with I2C sensors? This was a bit rough a while ago and the kernel support seems much more limited compared to the rpi4 for this type of use case. Any experience?

After updating my Orange Pi 5 I no longer can use the "opi5-i2c5-m3" overlay in /boot/armbianEnv.txt to activate and use i2c. Seems the file (or any ohter "opi5-i2c*") is gone from /boot/dtb folder. #uname -a Linux 5.10.110-rockchip-rk3588 #1 SMP Sun Apr 2 14:30:48 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux Is there a new or different procedure to activate i2c? Do I need to install a separate package for it? Or build the entire OS? Anyone else having the same issue? It does detect some i2c devices(0,10,2,6,7,9), but they don't seem to be related to the GPIO headers, prevoiusly I could also use (1,3,5). # ls -l /dev/i2c- i2c-0 i…

Hi all, Is anyone here good with upbringing MIPI panels on Linux via device tree modifications? I've had an attempt with a specific LCD panel but I am not having any luck to be honest. I would love someone to kindly review my Git Diff/device tree changes for any errors. I've attached my LCD init code as well, as well as the DSI portion of the dmesg output log, as well as my schematics for the custom driver board I have designed. https://drive.google.com/file/d/18E5zOGlNpdWLrD43R7bB4N-Mf_8mQFKY/view Thank you! DSI_Debug_Log.txt

Tried 5 diferrent microSD cards, 3 card readers, multiple redownloads on Mac and Windows. Diferrent power supplies, including 100W charger and 52pi EP-0136 direct 5v supply. No green LED, no LAN communication, no HDMI output. Everything i get is in log (via UART) Please help... i've got no more ideas. DDR Version V1.08 20220617 LPDDR4X, 2112MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB Manufacturer ID:0x1 Samsung CH0 RX Vref:32.7%, TX Vref:1…

I want to install the usb wifi/bluetooth card drivers but I keep getting an error during compilation. What to do? below code: DKMS make.log for rtl8812au-5.13.6 for kernel 5.10.110-rockchip-rk3588 (aarch64) Tue Jan 10 08:48:19 PM CET 2023 make ARCH=arm64 CROSS_COMPILE= -C /lib/modules/5.10.110-rockchip-rk3588/build M=/var/lib/dkms/rtl8812au/5.13.6/build modules make[1]: Entering directory '/usr/src/linux-headers-5.10.110-rockchip-rk3588' CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_cmd.o CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_security.o CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_debug.o CC [M] /var/lib/dkms/rtl8812au/5.1…

I am attempting to install the file Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop.img from https://www.armbian.com/orangepi-5/ but the installation hangs at the point where the root password should be entered. The same happens with the file Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_minimal.img. If i use the file Armbian_22.11.3_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop.img from the Github archive the installation completes. I have tried to raise a bug but the only solution for not booting are hardware and the installation has not progressed far enough to enter any commands. Any assistance welcomed.

Couldn't booti from NVME with armbian-config or armbian-install, finally I could do it, a dirty easy and convoluted following way. No details about burning stuff This is what I did 1) boot system from fresh downloaded SD (Armbian Jammy Desktop) 2) NVME setup (sudo gparted) - if empty create a partition table (GPT) if not delete all partitions - create 256MB FAT16 partition (nvme0n1p1) - create EXT4 partition (nvme0n1p2) - optionally create more partitions (system recovery, backups ...) - format partitions nvme0n1p1 -> FAT16 - format partitions nvme0n1p2 -> EXT4 - check partitions (if old N…

I am trying to play some dolby vision movies in Armbian (Orange pi 5) but the colours are not accurate. Do you know if it is possible to play DV movies and how? Thankd

I don t know for sure a wireless keyboard which works with the Orange Pi 5. Crosstalk Solutions says on his YouTube channel that the Rii (Upgrade) i4 Mini Bluetooth Keyboard with Touchpad, Blacklit Portable Wireless Keyboard with 2.4G USB dongle for Smartphones, PC, Table works with the Orange Pi 5: https://kit.co/crosstalk/orange-pi-5 But Crosstalk Solutions does not show a proof of function in his video, and I don t know anybody else who confirms a wireless keyboard who is working with the Orange Pi 5. Do you know a wireless keyboard?

I want to install jellyfin as a docker container on my Orange pi 5. How can I enable hardware acceleration for it? On the container page (https://hub.docker.com/r/linuxserver/jellyfin) there are instructions for various options, but orange pi 5 is not there of course. I have enabled 3D acceleration as mentioned on the armbian page for orange pi 5.

Ok I wasnt going to say But Sandi, says Prove The Shit. Who Is Wrong.... nyanmisaka left a comment (jellyfin/jellyfin-ffmpeg#765) I am unable to reproduce the issue. jellyfin-ffmpeg is intended solely for use with the Jellyfin server. If the custom version of our MPP dependency is causing your specific problem, please build your own version using the upstream MPP. Additionally, you completely ignored the issue report template. — Reply to this email directly, view it on GitHub, or unsubscribe. Triage notifications, keep track of coding agent tasks and review pull requests on the go with GitHub Mobile for iOS and Android. Download it today! You are receiving this because …

I haven't tried Jammy with 6.1.43 but the kernel doesn't say rc anymore so curious of the status. How does this build compare in terms of feature and performance with 5.10? Is all the video decoding supported? The RK3588 Kernel support page says that hdmi audio is not supported - is that really the case? Is gnome/wayland supported? I see that only KDE is listed there.

Version 20230325-edge with kernel 6.2 (pancsf-midstream). With HDMI USB LAN support. https://disk.yandex.ru/d/Xt36QdVcxRdEDA

In the most recent builds, the kernel logs have been flood with Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x800000100000351 Mar 02 21:31:38 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Unsupported format modifier 0x8…

Hi all! I'd like to share a small personal project that I've been working on recently for the Orange Pi 5 (and potentially other RK3588 boards). Like many RK3588 users, I wanted to run Kodi on a modern mainline Linux kernel instead of relying on older vendor kernels. After a lot of testing, debugging and learning, this project started to take shape, and I've a stable almost "all works" setup Tested on Armbian (minimal Debian and Ubuntu 24.04) with mainline kernel Not working: -HDR -Maybe some network services Next up: -Wayland support -Audio visualisers https://github.com/Danibos/mainline-…

I'm using ffmpeg and Kodi from the @amazingfate ppa. All has been running great although I don't think that I'm using hardware acceleration. I'm still on an older Jammy with the old/legacy kernel. I've tried newer kernels but getting issues so I stuck with the older kernel. I've started noticing lately that videos are being encoded with pixel format yuv420p10le. In Kodi, I was getting black screens while the audio was playing. I was following up on the Kodi forums, and was told that Kodi needed to be compiled for OpenGL instead of OpenGLES to make the video render properly. This is the thread: https://forum.kodi.tv/showthread.php?tid=379167 …

Is anyone using the current Kodi Flatpak, Omega? I'm having issues viewing videos that have pixel format of yuv420p10le with the current apt repository Kodi Nexus. I thought to try Kodi Flatpak and it worked and I was able to view those yuv420p10le videos without issue. However, it was choppy and had high CPU usage...around 80% on many of the CPUs. I'm trying to figure that out. It's happening on all types of videos. All is played using software decoding. I've never gotten hardware decoding working. In the Kodi Nexus version I'm using it also software decoding but very low CPU usage. In any case, just want to see what experiences …

Hello ! I've bought a Orange Pi 5 PRO board about 2 months ago . I've tryed all images (Linux and Android) from the official Orange Pi site . Later I tryed Armbian . In the end I've concluded that the best choice is Armbian 24.5.2 Noble Gnome ( Armbian_24.5.2_Orangepi5pro_noble_vendor_6.1.43_gnome-oibaf_desktop.img ). Using Armbian 24.5.2 Noble Gnome I got the best (the smoothest) video playback, both in video players and online (youtube) content . And it' s very responsive in operation, generally . I have one single issue : My MCE remote is not detected properly - the Play, Pause, Next, Previous, Forward, Rewind buttons did't perform any actions when …

Hi, I'm using orange pi 5, and I noticed that I'm using 100Mb/s instead 1000Mb/s, i changed the cables that are working in another pc to a 1000Mb/s but still works to 100Mb/s, I changed to another kernel like 6.12.32-current-rockchip64 with no luck, any idea how to solve it? root@opi5 /home/pi# ethtool end0 Settings for end0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Full 100baseT/Full 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Full 100baseT/Full …

Have an incident where I tried installing a newer kernel in an nvme working setup and the device wont post. My original installation flash card is working but is giving me problems. So I got 2 others and attempted to boot new version of the image and Im getting no post. I was able to solve my original problem by installing a legacy version in flash and copying /boot over to nvme. I also attempted rebuilding the mme partitions with no success. But it seems that there is something not working right with kernel 6.7.

altho there is no warning in the corner any more youtube is a slideshow, or if i am missing something please tell me what or how to enable it.

After upgrading today with "apt update && apt upgrade" I was no longer able to watch videos. mpv player would Segfault, also tried vlc - not working either. Gnome desktop with wayland itself works, only video playback seems to be affected. After rolling back the following packages in liujianfeng1994 repo it started to work again: librockchip-mpp1:arm64 OLD: 1.5.0-1+git221020.d63affb~jammy NEW, causes segfault: 1.5.0-1+git230210.c145c84~jammy The repository no longer has the old version, but I managed to get it back to 1.5.0-1+git221020.d63affb~jammy like this #Find the deb file from cache find /var/cache/apt -name '*librockc…

I just installed the most recent nightly image - this one looks like a major update but it broke armbian on my opi 5 1. I had to re-install the mali firmware to get x11/wayland to start - not sure why the update deleted the file 2. I had to re-install the mali-g610-firmware rockchip-multimedia-config packages 3. VLC cannot start the h264 decoder anymore [0000005583627590] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface. Warning: Ignoring XDG_SESSION_TYPE=wayland on Gnome. Use QT_QPA_PLATFORM=wayland to run on Wayland anyway. [00000055836b79e0] main playlist: playlist is empty [h264_rkmpp @ 0x7f4cc37630] Failed…

Hello, I have installed the minimal Trixie based image for Orange Pi5 (the image named Armbian_26.2.1_Orangepi5_trixie_current_6.18.8_minimal) and then attempted to build an out-of-tree kernel module. Having installed dkms and build-essentials, plus the kernel headers through armbian-config, I found the headers package hasn't been fully set-up, the build symlink in /lib/modules/<KVER> is missing and dkms complains that the kernel headers for the kernel are not installed. The kernel headers are installed though, but it looks like they're from a previous release (25.11.2 instead of 26.2.1). # dpkg -l | grep rockchip ii linux-dtb-cur…

I'm trying to setup LIRC on my OPI5 but I can't find any details on how that would be possible. I checked the kernel configuration and I cannot see any references to LIRC either. The module list has nothing obvious - is this feature completely disabled? Any suggested alternatives?

Howdy, I am in desperate need of help getting this dang usb wifi dongle working on my orange pi 5. I am new to sbc and fiarly new to linux. I have tried multiple github drivers with freash OS installs, all to no avail. Time spent trying to get it to work is reaching close 20 hours, across multiple forums, github searches, videos, linux how to site, and armbian site itself. I'm either missing something or an idiot cause i can't figure out this "make" or "dkms" command stuff out for compiling the driver and installing it. My last resort is asking for y'all for help before i feed this thing to my dog... "joke". My most recent attempt is from the git h…

I have my kernel locked to 6.1.75 but still after 25.8.2 update, I lost all USB devices on both of my Orange PI 5. Only the USB3 port is working. The only way I've been able to get access to the USB is by switching to the latest `current` kernel... Any clues on what is going on? Firmware or kernel upgrades are not doing anything... where can the issue be???? I tried downgrading to many different versions but beside the current branch, USB is gone. Thanks

hello , im a 0 in linux , i have orange 5 with mvme , i folowed how to for boot directly to mvme , the how to made me delete the spi flash. all was good, o5 boot on mvme succesfully but at each reboot , my hardware have new mac adress. any one can show me what to do step by step ? i used : Joshua-Riek/ubuntu-orange-pi5: Ubuntu 22.04 LTS for the Orange Pi5 ( desktop & serveur ) Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110.img.xz ubuntu serveur 23.04 ( 64 ) it's the same on all , boot one time i have mac adress , reboot = new mac adress i cant fix ip localy , so i think when i deleted spi flash , may be deleted…

Hello all, Is there any chance to run mainline kernel? Support for rk3588 seems to be starting with 6.2 and 6.3 (mainline has dts for rock 5b).

I got my Orange Pi 5 board to boot v6.1.20 I took all the patches from here: https://gitlab.manjaro.org/manjaro-arm/packages/core/linux-rk3588/-/tree/main/ and built from Armbian's latest trunk source. These patch(es) will need to be modified to support v6.2 & v6.3. > uname -a > Linux orangepi5 6.1.20-rockchip-rk3588 #trunk SMP Tue Apr 25 11:47:11 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux

Hi all, recently I installed the Mali GPU Drivers from the instructions on the official Armbian website. I have Armbian 23.02.2 Jammy installed, with KDE Plasma desktop. I found two problems: 1. The mouse flickers when I move it. This happens on both XFCE and Plasma (X11) 2. Every once in a while, the Plasma panels freeze and I have to reboot my OPI to get it to work. This also happens if I right-click on it and press "Enter Edit Mode". If I don't do that, it freezes randomly (afaik). This affects both the panels and the background (panels don't update, can't interact, cannot right-click). Does anyone know of any solutions to this? Thanks!

Hi all, I am trying to recover after a failed NVMe install. I have a working install on an SDCard, but I think my board no longer boots to SDCard, since I flashed the bootloader via armbian-install. I am not sure if my NVMe install is good or not, and I can't currently reflash it. So I think my best bet is to wipe the SPI, which I hope means the board will go back to booting from SDCard. That's question 1 - is that actually a valid solution? If I wipe the SPI will I be able to again boot to SDCard? I am able to get the board into Maskrom mode, and I can see it using the Windows tool. However, I believe that I …

I know this driver should be part of the recent kernel releases (and definitely avail for 5.10) but I am not sure how/why/where this driver would be in the armbian release. I also did install the firmware files but I don't see the module in the /usr/lib/module section. Any suggestions to build or enable this driver? Thanks

My microphone is not working on armbian jammy gnome Device : Opi 5 16GB I tried to use command arecord -l I showed 1 sound card Named rockchip or something like it with similar name.

Has anyone successfully migrated from 23.2 (stable) to 23.5 (stable)? Is that scenario possible today? I'm looking to get the Bluetooth working, I know it has been fixed in 23.5 but that one is currently broken.

Has anyone successfully set up a MIPI screen with their LCD ribbon connectors on Armbian? Any wisdom from someone who has done this would be appreciated.

Hey everyone, I'm starting to lose my mind here. I've got an Orange Pi 5 which works great with a micro SD card. Now I got myself a nvme ssd and all I want to do is move my system from the sd card to the ssd. I've created an image of the sd card on my PC using "dd" and then wrote it on the ssd using dd again. It seemed to work fine, the only issue seems to be, that the UUID of the partitions on the ssd were the same as on the sd card, that's why I changed the UUID of the root partition on the ssd using "tune2fs -U random /dev/nvme0n1p2". I booted up the Pi with my sd card again and used armbian-config to flash mtdblock0 (boo…

I have setup the hardware acceleration as explained in the posts, but within Kodi, every now and then I can see the image with "pixelising", and looking in the syslog when this just happened, I can read: Feb 15 16:54:17 orangepi5 kernel: [ 1267.908544] mpp_rkvdec2 fdc48100.rkvdec-core: reset done Feb 15 16:54:17 orangepi5 kernel: [ 1267.908549] mpp_rkvdec2 fdc38100.rkvdec-core: resetting... Feb 15 16:54:17 orangepi5 kernel: [ 1267.908670] mpp_rkvdec2 fdc38100.rkvdec-core: reset done Feb 15 16:54:17 orangepi5 kernel: [ 1268.316705] mpp_rkvdec2 fdc48100.rkvdec-core: resetting... Feb 15 16:54:17 orangepi5 kernel: [ 1268.316855] mpp_rkvdec2 fdc48100.rkvdec-core: …

I finally got wifi working on a fresh install of 24.5.1. Video acceleration is working perfectly in Chromium but I am not having any luck playing h264 mp4 videos with hardware acceleration in vlc or mpv. Is this possible or am I missing something? CPU is around ~30% with chromium playing 4k youtube but if I play one of my mp4 files it's a solid 130%

Anyone have any success getting this module for new MediaTek WIFI 6 adapters? I've tried this backport of the mainline driver but get this compilation error. https://github.com/astsam/mt7921/issues/1 Anyone any ideas?

Hello, I tried to setup a network bridge on the Orange Pi 5 to utilize with Qemu/KVM and some virtual machines I have. Here is my armbianmonitor output: https://paste.armbian.com/dajivikohi I edited /etc/netplan/armbian-default.yaml and modified it to setup a simple network bridge. I've done this countless times on other hardware I have. I rebooted, but the bridge fails to initialize and the screen gets an error dumped out every 5-10 seconds: rk_gmac-dumac: fe1c0000.ethernet eth0: Adding VLAN in promisc mode not supported rk_gmac-dumac: fe1c0000.ethernet eth0: failed to initialize vlan filtering on this port Is bridg…

Loading the latest dist with 5.10.160 kernel, the header package has wrong version...

when I switch to static IP, there is no a connection to default gateway. but when using DHCP everything works fine. $ ip route default via 192.168.88.1 dev end1 proto static metric 100 169.254.0.0/16 dev end1 scope link metric 1000 192.168.88.0/24 dev end1 proto kernel scope link src 192.168.88.32 metric 100 $ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 2: end1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 …

I have no sound over hdmi with my Orange pi 5. I have tried installing alsamixer and alsatools but this reports no settings to adjust. I have looked in files-boot-config for the sound settings and line 5242 says HDMI analogue is not set. I tried altering that to =y but I am not allowed to alter anything here and save it, ( oh how linux loves denying you permission). Does anyone know how to apply some common sense to this, why do the Armbian developers think it is a good idea not to have sound over HDMI, there is no option at al to select this in sound settings. Yours extremely miffed.

I'm struggling to get my Orange Pi 5 to boot to NVMe with Armbian 23.02 Bullseye CLI. With armbian-install I picked: 4 Boot from MTD Flash - system on SATA, USB or NVMe then install to /dev/nvme0n1p1, followed by updating the bootloader on mtdbblock0, and then powering off. When I remove the SD drive, and reboot. The console remains blank. When I insert the SD drive, and reboot again, the system comes up, and I can mount /dev/nvme0n1p1: $ df -h Filesystem Size Used Avail Use% Mounted on udev 7.7G 0 7.7G 0% /dev tmpfs 1.6G 9.6M 1.6G 1% /run /dev/mmcblk1p2 30G 2.0G 27G 7% / tmpfs …

G’day guys, just grabbed a version of Armbian again to play around with on an orange Pi 5 I have had for a while. I have installed the latest stable (25.5.1 Noble Gnome). Everything went smoothly, and I have a 512GB ssd on the board, so I went through the install process using armbian-install. I managed to get the OS installed on the SSD, but when I went to install the bootloader, I got some error messages saying that the SPI image was not chosen. I followed the process for erasing the MTD, but still I got error messages relating to no spi image. I tried to boot from the ssd and just got a black screen. I downloaded Joshua Riek’s Ubuntu 24.04 dist…

booted opi5 via nvme one day and the boot screen mentions about btrfs partition missing even tho it was using ext4 partition. booted via sdcard and the root partition is entirely missing on the nvme. the boot partition is still there and working. not sure if relevant but the previous time i shut the opi5 down, i forgot to unplug it and it was plugged in for about an hour after shutdown with the red led and fan on. the nvme is kingspec which while cheap doesnt seem to have that many bad reports online that i can find (the boot partition was fine so i suspect kingspec isnt at fault). the power adapter is a 25w phone charger w/ pd/qs; it hasnt exhibited any weird behavior (l…

My first post here - I'm new to SBCs and stoked I got my home webserver up and running on a Orange Pi 5 which boots from an NVMe (pats-self-on-back : -) It runs great, pages are up, and it's all SO COOL, but it fails to do a restart... I can do a shutdown -h now, count to three and power it back up and all is well, but if I do a shutdown -r now it will go down, start back up, all the way to the login prompt but then barfs a long Oops message. God please... don't make me start over !

Hi guys, Would someone point me to where to get a particular distro, mainly looking for jammy_legacy_gnome-amazingfated_desktop for OPi 5 Pro ? I have jammy_legacy_5.10.160_gnome-amazingfated_desktop for Pi5 and Pi5 Plus but it does not work on the Pro version. thank you in advance.

Hi, after upgrading to Armbian 24.11.3 noble with 6.1 Kernel I have this problem that every time I turn off my TV that is connected to OPI with HDMI, then turning it back on again it will never have a HDMI signal. Same thing happens when I unplug the HDMI cable and plug it back in. I can reproduce it every single time - not just occasionally. It is not a hardware or cable problem, the exact same setup has worked flawlessly for long time with older Armbian and 5.1 kernel. I tried disabling all of the KDE power saving settings, also totally disabled kpowerdevil - with no change. SSH still works fine, the OS has not crashed. …

Ubuntu Noble had some early day issues with default key ring not being stored properly and or synced to the logged in user and users getting popup prompts about the default keyring locked. A week ago I downloaded Armbian Noble 25.5.2 desktop onto my OPi5. It has been my daily driver for the past week or so. It has been a really nice release for my OPi5. All has been good except the default keyring popups. I have created new users, deleted stored keyrings, changed passwords among other things. At this point I am able to store the default keyring password (which is the same as my login PW). However, when launching chromium, and ProtonVP…

Hello friends: I have opi5 with the spi removed, which spiloader do I use to boot from the sd card? Thank you so much

FYI. Searching some forums around the web, stumbled on a post that indicated the TU3 Nano would work on the OPi 5. I thought I would give it a try. It worked for me plugged it in reboot. Download speed topped out at 200mb on the usb3 (top plug) connected to 5Ghz wifi. Happy days. Running the Feb.27 stable version of Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110_gnome_desktop. TC

Hello friends, htop does not show me the temperature, I am attaching information about my system (I have the libsensors library installed). If someone can help me please. Thank you. OS: Armbian 24.5.0-trunk.89 trixie aarch64 Host: Xunlong Orange Pi 5 Kernel: 6.8.0-rc1-edge-rockchip-rk3588 Uptime: 1 hour, 14 mins Packages: 333 (dpkg) Shell: bash 5.2.21 Terminal: /dev/pts/0 CPU: (8) @ 1.800GHz Memory: 187MiB / 7687MiB

please, helpme with thist message in boot :

Degin: MounlAng root Tile syslel ... Degan: munning escrapusr cucad-lop ... uonc. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. done. Geve up waiting for root file system device. Cowmon problems: ⁃ Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! UUID=db80a2ac-ec37-4fda-91db-92604becfcce does not exist. Dropping to a shell! BusyBox v1.30.1 (Ubuntu 1:1.30.1-7ubuntu3.1) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) …

I was able to flash armbian bookworm cli to the ssd using balena etcher but when I boot the OPI5 from the sdcard and run lsbk it can only see the sdcard any ideas ...

Hi there, my new OPi5 with Armbian Bookworm Cinnamon mesa backoprted does not see my mPCIe SSD disk. Just got this: https://allegro.pl/oferta/nowy-superszybki-dysk-ssd-512gb-m-2-nvme-2242-9605598735 \ module, but it is not recognized by the system. Armbianmonitor output: https://paste.armbian.com/huhedogene lspci -v output: 0004:40:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0, IRQ 89 Bus: primary=40, secondary=41, subordinate=41, sec-latency=0 I/O behind bridge: [disabled] [16-bit] Memory behind bridge: [disabl…

Hi there, I pourchased OPi5 (not preferred OPi5 Pro, because of Armbian lacking support), flashed Debian 24.8.1_bookworm_6.10.6_cinnamon_backported_mesa_desktop, configured (user, switch to static IP, user). Worked OK. Now, ssh'ing into showed "113 packages upgrade". Did "apt upgrade". Download OK, but when applying apgrade process hung twice: - once on "configuring libc", had to power off, then restarted (after an apt-get suggested in response to apt upgrade). Upgrade hung second time (no progress on bottom bar for hours, no new ssh session). - twice was on "configuring udev". After this, board is almost dead: - boots to anima…

Hello, I am trying to create a custom uboot using armbian. it's possible? I am using the following command but I cannot generate the "uboot.bin" to save it to the spi: ./compile.sh uboot-config BOARD=orangepi5 BRANCH=current BUILD_DESKTOP=no BUILD_MINIMAL=yes BUILD_ONLY=u-boot CONFIGURATION=stable KERNEL_CONFIGURE=no KERNEL_ONLY=no PROGRESS_DISPLAY=plain RELEASE=bookworm UBOOT_ONLY=yes Thank.

for some strange reason the content of armbianEnv.txt (rootdev) is not applied in my opi5, if anyone can help me. Thank !!!

Hi all, Testing this OP5, got a standard M2 NVMe SSD (this works on my OP5Plus) I have formatted to exFAT with windows, inserted on the OP5, loaded ArmbianOS on MicroSD, it boots fine but I cant get it to show the nvme drive using fdisk -l or lsblk It seem like its not detecting the m2 nvme ssd at all.. little help please ?

Hi, I have downloaded and tested the 6.12 kernel Minimal/IOT images and they are not booting. I downloaded trixie 6.1, booted, then manually installed latest 6.12 with armbian-config and the reboot failed. I re-flashed sd card with 6.1, installed edge 6.16.4 (latest) with armbian-config and it booted fine.

Good day, I have Opi 5 and bought this display https://www.aliexpress.com/item/1005005641383181.html?src=google&aff_fcid=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&aff_fsk=UneMJZVf&aff_platform=aaf&sk=UneMJZVf&aff_trace_key=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&terminal_id=b834b596955b44a1bf643629f5ba5647&afSmartRedirect=y . It was a blind buy ... And now I can't get it work if its even possible. I'm its my first time trying to get display on these boards usually use them trought Monitor or TV and it works flawlessly. Cant find even config.txt . But now im lost at how to get …

System Information: https://paste.armbian.com/mozehisomu When i am trying to setup many vlan interfacces i have whis dmesg message: rk_gmac-dwmac fe1c0000.ethernet eth0: MAC_VLAN_Tag_Filter full (size: 4) interface info: ethtool -i eth0 driver: st_gmac version: Jan_2016 firmware-version: expansion-rom-version: bus-info: supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: yes supports-priv-flags: no I need about 20-30 vlan interfaces

Hi Basically the subj sums it up. I got the AP6275P wireless module with Armbian, and BT is not functional. `hcitool dev` doesn't show the device in its output. Neither does `rfkill`. It works with the Ubuntu image published by Orange Pi though, so it doesn't look like a hardware issue. I'm using Armbian 23.5 Jammy Gnome with the 5.10.160 kernel. Happy to provide any additional data.

Hi all Armbian fans, As of today, I checked officially platinum supported Armbian version for Orange Pi 5. I was amazed how low performing is armbian image. I was using latest armbian with HW install procedure at: https://redirect.armbian.com/orangepi5/Jammy_legacy_gnome , and Ubuntu from https://github.com/Joshua-Riek/ubuntu-orange-pi5/releases/download/v1.11/ubuntu-22.04-preinstalled-desktop-arm64-orange-pi5.img.xz Both glxinfo -B says: Accelerated : yes Armbian glmark2 Score: 705 Ubuntu glmark2 Score: 1285 Difference is HUGE When we could expect any "normal" Mali…

Hello, my Orange Pi 5 works well with the stock OS (1.22, Ubuntu Jammy, BSP kernel 6.1.99), using the SD as a boot device. It also works ok with Armbian Minimal-IoT / Debian 13 / 6.1: v25.8.2 for Orange Pi 5 running Armbian Linux 6.1.115-vendor-rk35xx But I prefer Ubuntu and wanted to try 6.12, so I downloaded 25.8.2 / Ubuntu Server / 6.12. Wrote to SD, hooked up the debug UART and powered on. The bootloader is fine, the kernel starts, but at a certain point it panics: [ OK ] Reached target sockets.target - Socket Units. Starting armbian-hardware-monitor.…ce - Armbian hardware monitoring... …

Hello, I have an orange Pi5, i had installed armbian a few years ago and everything was working fine. Roughly one year ago i turn it off and kept off until now. A few days ago I tried to turn it on again and i've inserted a new sd card containing armbian but it doesn't boot. I've re created the sd card a few times and also used another sd card because i was thinking something was wrong with the card. The board turn on but i got only the red led, and is stable. Searching on internet i found that maybe the Orange Pi is bricked, so i tried to use the MaskRom and Recovery button, but nothing happen. Also i'm not able to see the board inside the RKDevTool, neithe…

Orange PI 5 doesn't boot after firmware update using ARMBIAN beta tool. There isn't so much documentation, as this board is new. How to recover the firmware?

Hi all, I’m new to this whole SBC thing, and I recently got an Orange Pi 5. I first installed the official OS (Ubuntu), where I needed to do into orangepi-config and go into System > Hardware > wifi-ap6275p and enable that to use the official M.2 WiFi dongle. However, I don’t see this option on Armbian. Does it not support it?

Hi all, I'm trying to debug a sporadic problem with my Orange Pi 5 (16GB) which I'm unable to reproduce. I'm hoping maybe someone else experienced a similar issue or at least has any pointers on how to debug it further. The problem: At random times of the day, the board just appears to freeze up. All communications stop. Board is powered on, with red LED on and green LED off. I have to manually unplug the device to reset it. Within the last 2 weeks, this happened 3 times already. Each time, the last log appears to be a journalctl flush (example: https://pastebin.com/dDm5Xtis - the board froze at midnight, no more logs until …

My orange pi 5 armbian Os isn’t displaying hdmi output to my monitor. However, it works on my flat screen tv, any reason why this might be ?

Hello All, Do you also have this kind of messages in syslog ? [ 1601.687044] ------------[ cut here ]------------ [ 1601.687070] WARNING: CPU: 2 PID: 112 at drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2986 vop2_crtc_load_lut+0x54/0x310 [ 1601.687075] Modules linked in: bnep zstd joydev sch_fq_codel fuse ip_tables ipv6 r8152 panfrost gpu_sched [ 1601.687114] CPU: 2 PID: 112 Comm: kworker/u16:1 Tainted: G W 5.10.110-rockchip-rk3588 #trunk.0184 [ 1601.687117] Hardware name: Orange Pi 5 (DT) [ 1601.687127] Workqueue: events_unbound commit_work [ 1601.687134] pstate: 40c00009 (nZcv daif +PAN +UAO -TCO BTYPE=--) [ 1601.68713…

orangepi5-max:~:% sudo apt upgrade -y Upgrading: armbian-bsp-cli-orangepi5-max-edge bsdutils fdisk libbz2-1.0 libmysqlclient24 libudisks2-0 linux-u-boot-orangepi5-max-edge rfkill zlib1g-dev armbian-firmware bzip2 gnu-coreutils libfdisk1 libsmartcols1 libuuid1 login udisks2 armbian-plymouth-theme diffutils libattr1 libminizip1t64 libssh-4 linux-dtb-edge-rockchip64 mount util-linux base-files eject …

Hi all, this is my first post here on the forum. I'm getting ready to wrap up for the night, but I recently purchased an Orange Pi 5 (non-B) to do some tinkering with. I downloaded the Bookworm XFCE variant as I am somewhat familiar with XFCE already. Anyway, upon initial testing, I thought my power supply wasn't good enough for the board. I wasn't getting any HDMI output. When I removed the micro-SD card and tried to boot it that way, an orange pi splash screen would show on the attached display, so I think the port actually works (?) I have a spare USB to TTL Serial adapter so I was able to verify the board was successfull…

Stable, weekly and CI builds https://www.armbian.com/orangepi-5/

Is it possible to use the onboard microphone of Orange Pi 5 on Armbian? It does not seem to turn on

I have created a micro desktop case. It's an open design that is still in the creation phase. The shell is 3d printed, the sides are acrylic, and the opi5 mount panel can be 3d printed or made from acrylic. I'm looking for feedback with design suggestions/needs. This is the first real opi5 micro tower design currently for OPI5. My cad drawing of the OPI5 mainboard is 99.9% accurate, so if someone wants to use that as a footprint for other projects by all means. https://github.com/berin-aquaquad/orange-pi-5 I am using DesignSpark Mechanical a free cad software that is on par with Fusion360. The shell has been designed as a split body so smaller 3d printers can c…

The OPI5 has an onboard RTC. On the back of the board near the RTC chip there are two pcb "test points". One says RTC1, the other says GRD1, I would assume a CR2032 could be connected to those points to maintain RTC function. I don't dare do anything till I get a solid answer. Can anyone give me any feedback as to options.

Orange pi 5 (i dont find way hot to make it in orange pi 5 section) English is not my native, i hope you understand and sorry for mistakes I spend like 3 days on this problem and i think i am stuck I tested offisial image and Josua and there i can use my wifi normally Setup orange pi 5 v1.3.2 clened spi (i got problem like here) armbian 26.5.1 vendor 6.1.115 (from armbian imager on windows) sandisk extreme 64gb sd card after boot i runs sudo apt update sudo apt upgrade -y armbian-config (choose orange pi 5 ap6275p overlay) /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both e…

A new variation of Orange Pi 5 is now available. I think it's available on AliExpress, but I've seen the item on Amazon.com as well...reasonable price: https://www.amazon.com/Orange-Pi-Rockchip-Frequency-Development/dp/B0C5BZLPZN It comes now with the RK3588 instead of the RK3588s of the 5 and 5B. It's similar in capabilities of the Rock 5B but I believe has a few more bells and whistles. It has two 2.5GB ethernet ports. Separate connectors than GPIO for RTC and fan. Full size HDMI input as well as 2 full size HDMI outputs. Can have m.2 for 2230 WiFi/BT on top side as well as m.2 2280 on bottom of board. I think it can only go up to 16GB me…

My Orange Pi 5 appears to be completely dead. No lights turn on when the power is connected and the SD card is freshly imaged as well. This started happening when I connected a USB-C multi-port dongle with a connected PD power supply to it. Is it possible to revive this?

/boot/armbianEnv.txt rebooting pwm all display working fine

Orange Pi 5 is a new board using RK3588S. I think it would be really nice to support it http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5.html

Expected Behavior: I am able to enter sleep mode, either graphically or using systemctl suspend, and then wake from sleep mode by typing on the keyboard or pressing the power button Current Behavior: The system appears to enter sleep fine, but once in sleep pressing the power button or pressing buttons on the keyboard seems to do nothing (pressing keys on my keyboard causes it to light up, however my mouse does not light up). The display remains blank and the green led does not blink. I have to do a forced shutdown by holding the power button or unplugging the power supply. Note: the behavior is the same no matter if I suspend from a desktop sessio…

Hello, I have a problem with mounting a USB HD via fstab. If I enter the HD in the fstab, the system hangs when booting. The problem, USB is not activated yet and will be loaded later. If I remove the HD from fstab, it is automatically mounted under /run/media/USER. However, this must not be mounted under a user, but should be mounted as root. What can I do. Thanks very much

Hi I want to work with g_audio drivers on the usb type c otg port. When I build the image with current kernel, by applying the following overlay (I only change dr_mode to peripheral) i am able to convert the usb port in peripheral mode and successfully load the g_audio drivers and audio interfaces also come up. /dts-v1/; /plugin/; / { compatible = "rockchip,rk3588s"; fragment@0 { target = <&usb_host0_xhci>; // This matches the label in the device tree __overlay__ { dr_mode = "peripheral"; }; }; }; But when i want to do similar with the vendor kernel, which has different device tree, c…