Rockchip

I have a couple Orange Pi's, and the HDMI is broken. I noticed that many believe that it is Armbian, but it is not. Orange Pi's probably won't be where we want them until 2025. I found a couple notes from development teams, one below and one from September. Both say the same thing: essentially it's in the works: "The RK3588 SoC family integrates the newer Synopsys DesignWare HDMI 2.1 Quad-Pixel (QP) TX controller IP and a HDMI/eDP TX Combo PHY based on a Samsung IP block. Add just the basic support for now, i.e. RGB output up to 4K@60Hz, without audio, CEC or any of the HDMI 2.1 specific features." https://patchwork.kernel.org/project/linux-rockchip/pa…

• 0

  Reputation Points

• 1 reply
• 3.7k views

ozacas

October 10, 20242 yr

Hello, I own a RockPro64 and I'm using Armbian Legacy Buster 4.4.213-rockchip64. Everything mostly works, although I've had a pretty annoying issue. Reboot just doesn't work. Every time I do a 'sudo reboot' (or any equivalent for that matter, as for example 'sudo shutdown -r now') it doesn't work. Although it apparently reboots, the TV monitor to which my box it's connected via HDMI lose connection and all, nothing actually happens. Both the red and the white leds of the RP64 turn on and keep on all time (instead of just one of them blinking, as expected) and then it will work only if I poweroff and on again, either by unplugging the power cable or…

• 1

  Reputation Points

• 25 replies
• 11k views
• 3 followers

JMCC

January 6, 20215 yr

I have 85 tinkers running with armbian 5.41 xenial next 4.14.23. Normally I run a script that apt upgrades them all but I run a small batch of them first as a test. Today I ran apt update/upgrade on three of them and they are all bricked. No output to the screen. Can't ping them. Any ideas?

• 1

  Reputation Points

• 70 replies
• 45.1k views

freak

September 3, 20197 yr

I have set up Armbian 24.8.4 bookworm on my 32GB Orange Pi 5 Plus. Most everything works as expected out of the box. The second HDMI port doesn't detect the second screen, and the screen displays No Signal. I have tested the cables and monitors to ensure they are functioning. I have also ensured I wasn't plugged into the HDMI input by accident. I was about ready to proclaim it a hardware issue, but on booting the "Official" Orange PiOS Arch image, the dual monitor support worked as expected. I checked the dtb file included with the Arch image, and it has many references to HDMI0 and HDMI1 devices, while the one used by default with the Armbian ima…

• 0

  Reputation Points

• 5 replies
• 5.7k views
• 1 follower

royk

October 27, 20241 yr

Hi Igor and all, back after a long absence, Have been using Cubie2s since 2015, rock solid with Armbian. I've now moved as cubies don't support gigabit, and the Pi gigabit interface is limited. So I now have a tinkerboard and popped Stretch mainline kernel 4.14.y onto an SDcard. Linux tinkerboard 4.14.67-rockchip #88 SMP PREEMPT Wed Aug 29 15:07:29 CEST 2018 armv7l GNU/Linux I want to compile the faithfull usb-redirector against the headers, but sudo apt-get install linux-headers-`uname -r` results in not found. Bit of noob question, but I've trawlled around, but can't seem to find source/headers or should I move to a diffrent version? Mark

• 1

  Reputation Points

• 2 replies
• 3.3k views

MarkA007

December 21, 20187 yr

Hello, After 5 years of loyal service, my Helios64 SBC just died on me last night. Would a Radxa Rock5 ITX+ and a M.2 to Hexa SATA Adapter could be a good drop in replacement to reuse the case? Both are Mini-ITX so it would fit. I know I would lose the front panel lights and power/reset button, and I would need to cut the back panel to fit the I/O shield but these are minor problems. What I am more concerned with, is if it is at all possible to power the 5 HDD from the radxa board (as the Helios 64 board didi). Helios engineers had made it possible to do it with minimum power, mainly by starting up the drives sequentially. …

• 0

  Reputation Points

• 6 replies
• 2.6k views
• 1 follower

luneth

December 26, 2025Dec 26

Before writing I searched the forum a bit but couldn't find any recent posts about it. I have an OPI5 board and on NVME I would like to install armbian. I downloaded the image to micro sd and it boots fine. At this point I don't know what to do because I had to waste a lot of time on it some time ago and I don't remember the steps. With the armbian-config utility is it possible to clone the armbian release I am using on the micro sd? I remember that this wasn't possible some time ago. I would like to know specifically the steps to take and whether it is advisable to delete any old partitions on nvme. Thank you

• 0

  Reputation Points

• 8 replies
• 13.6k views
• 1 follower

Lele

December 29, 20241 yr

Hy, I miss a few options in the kernel current kernel: ARMBIAN 5.36 user-built Ubuntu 16.04.3 LTS 4.4.102-rockchip Thinkerboard I still need: 1) - disable HDMI audio so that it will no longer be displayed as a sound card under "aplay -l" deactivate "card 3: rockchipminiarm" same as with the image kernel update of Igor root@se:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Audio [USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Audio [USB Audio], device 1: USB Audio [USB Audio #1] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Audio [USB Audio], device 2: US…

• 0

  Reputation Points

• 19 replies
• 9.2k views

Igor

March 12, 20188 yr

Hi there, I have set up a tinkerboard S and I'm loving armbian so far. I only just encountered a weird problem. When i try to code in spyder3 there seems to be a messup in the keys i press and the key that is produced in spyder3. The funny thing is that this only occurs in spyder. When I type in terminal or gummi everything works fine. I am connecting to my TB using vnc using X. I've googled a bit around and found this could be a error of the XKEYBOARD as written here (I am however still not sure): https://github.com/spyder-ide/spyder/issues/3713 However I cant apply the proposed solution. I've found i need to go to /etc/X11/xorg.c…

• 0

  Reputation Points

• 0 replies
• 2.3k views

MEMEs

November 10, 20187 yr

I run a audio loop code on a Raspberry pi 4/5 and Orange Pi 5. The latency of audio loop is 0.2 seconds on Raspberry pi but on orange pi it takes 1.2 seconds. For orange pi, i am facing this problem with different Operating systems as well apart from armbian. I've used Ubuntu, Orange Pi OS, Armbian. All have got this problem. The code I have attached. Since the issue is faced in multiple Operating System I strongly feel this has to do with the driver level softwares or directly related optimization from Rockchip. Can anyone guide what I could do audio-loop.cpp

• 0

  Reputation Points

• 1 reply
• 2.7k views

royk

November 14, 20241 yr

After upgrading to kernel 6.8, I've noticed my orange pi 5 running a bit hotter than when using kernel 5.10, even with the CPU load a little bit lower than before. Nothing alarming, just an observation. Did anyone else notice the same behaviour?

• 0

  Reputation Points

• 0 replies
• 1.7k views

Tiago Esperança Triques

June 27, 20242 yr

Hello, I installed Armbian Hirsute xfce bleeding edge kernel 5.13.y on my RockPro64 4GB and updated it right after that. After restarting after the update, ethernet doesn't work anymore. (Wifi connecting icon is shown and no connection to ethernet) dsmesg says that the link is up. armbianmonitor: https://paste.ubuntu.com/p/9Yz8SJVrzS/ apt/history.log: https://paste.ubuntu.com/p/GQbfZp3Xch/ For apt history only the last two operations seem relevant. I assume the previous ones are made by whoever/whatever created the image.

• 1

  Reputation Points

• 5 replies
• 4.3k views
• 2 followers

ScottP

September 24, 20215 yr

Is there an Armbian image with home assistant that isn't minimalistic? or Is there a way to install HA on a more robust desktop armbian 25.2 image for the Orange Pi 5 Plus? I feel the orange pi 5 is robust enough to handle HA under a desktop Armbian environment than other SBCs.

• 0

  Reputation Points

• 6 replies
• 6k views
• 1 follower

eselarm

July 25, 20251 yr

RTL8852BE is the official recommended Wifi module for Orange Pie 5 PLUS, but it is not available in Armbian 24.5.1 Linux Vendor Kernel 6.1 without a driver module. Hope the official driver will be added to the 6.1 kernel. Thanks.

• 1

  Reputation Points

• 13 replies
• 16.5k views
• 2 followers

bolet75

July 15, 20242 yr

Scan ssid by mobile phone the SSID can be seen . but always in password loop. I've installed hostapd V2.7 and dnsmasq V2.79. and wpa_supplicant and networkmanager are stopped. The config files are as below: 1: etc/hostapd/hostapd.conf interface=wlan0 driver=nl80211 ssid=TinkerNet hw_mode=g channel=7 wmm_enabled=0 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=3 wpa_passphrase=mypassphrase wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP 2:/etc/dnsmasq.conf interface=wlan0 # Use the require wireless interface - usually wlan0 …

• 0

  Reputation Points

• 2 replies
• 3.8k views

SecureXperts

May 31, 20197 yr

Hello, I have Tinker Board. If I install Armbian I see screen only over HDMI. I would like to enable DSI touchscreen display. Is it possible? How make it? Thank you

• 0

  Reputation Points

• 1 reply
• 4.8k views
• 1 follower

TonyMac32

June 25, 20179 yr

Hello everyone, I flashed the armbian into my tf cand and inserted it into my OrangePi 5 Plus, with my fans inserted to the specific socket on board (2pin, 1.25mm, 5V, PWM3_IR_M1). However, when I booted it, the fans was running constantly instead of controlled by temperature dynamically, like the official OS images that did only the fans running when the temperature over 50 celsius. I wanna know how to configure my OS to enable the temperature-controlled fans like the official images. The offical documents shows: Linux uses the default pwm-fan drivers to control thye fans and the device tree was defined in orange-pi-5.10-rk3588/arch/arm64/boot/dts…

• 0

  Reputation Points

• 2 replies
• 5.4k views
• 1 follower

The Tall Man

September 5, 20251 yr

As the title says, how can I install the ntsync kernel module for use with Wine/Proton?

• 1

  Reputation Points

• 4 replies
• 4.1k views

The Tall Man

September 10, 20251 yr

hi all, so i skipped i beleive 2 releases of armbian for opi5 and i just downloaded latest and installed. i am not english native and armbian installs local langauge automaticaly wich is ABSOLUTELY NOT WANTED and quite annoying from my perspective. what i need is just plain en.us or english internatinal for system and keyboard but i cant get it. i tried changing it with armbian config but it doesnt do a thing, local language is always there and its a huge PITA. please armbian dudes, return to manual selection, i beg you. any tips how i can fix it so its just plain english? or how can i force installation to ask me what language to choose? thanks for an…

• 0

  Reputation Points

• 0 replies
• 2.8k views

Dim3nt0

August 15, 20233 yr

Hello, my development board is Rock5B, and I am using the Armbian system for a recent project. I have already compiled the firmware in the armbian/build/ directory, and the device starts up normally. I want to modify and customize my U-Boot and kernel. After compiling Armbian, I would like to recompile U-Boot or the kernel in the armbian/build/cache/sources directory. Are there any commands to rebuild U-Boot and the kernel?

• 0

  Reputation Points

• 2 replies
• 3.4k views
• 1 follower

lyh

November 25, 20241 yr

I searched & tried all materials I can find, trying to set up FFmpeg to work with hardware acceleration on Orange Pi 5. But it did NOT work. Anyone else succeeds in using GPU hardware acceleration to encode/transcode video on Orange Pi 5 using FFmpeg? (or using gstreamer?) Could you please share with me the way to do it? Thank you very much indeed!

• 1

  Reputation Points

• 13 replies
• 47.9k views
• 1 follower

jyce

July 3, 20242 yr

I recently updated from bookworm to trixie, here's how i did it: commands: sudo apt update sudo apt upgrade -y sudo cp -p /etc/apt/sources.list /etc/apt/sources.list.bak sudo sed -i 's,bookworm,trixie,g' /etc/apt/sources.list sudo cp -p /etc/apt/sources.list.d/armbian.list /etc/apt/sources.list.d/armbian.list.bak sudo sed -i 's,bookworm,trixie,g' /etc/apt/sources.list.d/armbian.list sudo apt dist-upgrade /etc/apt/sources.list : deb http://deb.debian.org/debian trixie main contrib non-free non-free-firmware # deb-src http://deb.debian.org/debian trixie main contrib non-free non-free-firmware deb http://deb.debian.org/debian trixie-updates main…

• 1

  Reputation Points

• 2 replies
• 11k views

lovenemesis

October 15, 2025Oct 15

Hi everyone, New to the forum, so apologies if the questions are answered elsewhere, but please redirect me if they are. I have identified a bug in the `armbian-install` script in the current Bullseye Edge image (Dec 19,2022) that prevents it showing NVMe targets in the installation prompt if they don't have a valid filesystem on them. This appears to have been fixed on the 19th of December in this commit (the grep for filesystems was removed from the lsblk command that returns valid partitions). https://github.com/armbian/build/commit/893ed2347d97af574becf69dee1166a1bf933081#diff-8752ea87e0340f217187b70f7b08735d872a14c0467d02a6285222e594db3299L63…

• 0

  Reputation Points

• 1 reply
• 3.3k views
• 1 follower

Igor

January 31, 20233 yr

Hello, I want to extend the current kernel (Tinkerboard with rockchip-kernel-4.4.120 on Debian-Armbian) to include IR (GPIO) and DVB modules. What do I have to consider or is this possible with the usual run-through? (copy .config from current system, make menuconfig, make, sudo make install, sudo make modules_install) Is there possibly already a tutorial that I have not seen? Clash

• 0

  Reputation Points

• 8 replies
• 10.2k views
• 2 followers

Igor

April 14, 20188 yr

hello i just installed Armbian_5.59_Tinkerboard_Ubuntu_bionic_next_4.14.67_desktop on a new tinkerboard s .. and ran myself into a corner immediately. i was trying to figure out how to get 4K 2160p resolution instead of HD 1080p. i changed the refresh rate from 60Hz to 30Hz and now can't get the display back. i tried reboot. and documentation at https://docs.armbian.com/User-Guide_Fine-Tuning/ said to modify /boot/boot.cmd and that file says "edit /boot/armbianEnv.txt to set supported parameters" .. . so i set disp.screen0_output_mode=1920x1080p60 in armbianEnv.txt no luck .. i seem to have gone headless earlier than planned .. advice pls? i w…

• 0

  Reputation Points

• 1 reply
• 3.2k views

jmandawg

October 2, 20188 yr

I have installed Armbian on my Rock Pi S, done some setup, and then taken an image of the disk to be duplicated to other devices. The problem is that each of these devices get the same permanent MAC address on the ethernet port as the first device. I don't know how Armbian gets the MAC address from the interface but it doesn't seem to depend on unique hardware, or if it does then the hardware ID isn't actually unique between boards. This leads to problems because my device is meant to be used several in the same network, causing collisions in DHCP assignment etc. I have tried multiple workarounds and none have worked well. I tried spoofing the MAC addr …

• 0

  Reputation Points

• 6 replies
• 6.5k views
• 1 follower

Meestor_X

May 1, 20251 yr

i have upgraded armbian on tinkerboard asus form 5.35 to 5.38. And this changed cpu governor to conservative. I have changed it to performance. BUT previous max cpu speed was 1.80GHZ and now i have only 1.61.GHZ I have cooler with fan on my tinkerboard and iam not scared high cpu temperature. Hov to get back to the maximum 1.80 GHZ frequency ???? I cant add 180000MHZ via sudo nano /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies to each core permission denied. please help

• 1

  Reputation Points

• 22 replies
• 15.6k views

constantius

April 15, 20188 yr

Hello! Is there a possibility to change the default LED0 behaviour of the RTL8201F PHY? Here is the Datasheet: https://file.elecfans.com/web1/M00/99/0F/o4YBAF0VytaAI7ezABH66fmIRIg854.pdf?filename=RTL8201F-VB-CG.pdf And this is the relevant register: It states, that "11" is the default - but I think it is changed to "00" during driver initialization - is that possible? I would like to change it to "01" - is this somehow possible without recompiling the driver? Thank you! Best regards, Manuel

• 0

  Reputation Points

• 2 replies
• 2.1k views
• 1 follower

mm2189

August 16, 20251 yr

Per Radxa here, it is possible to obtain CPU temperature via "sudo cat /sys/class/thermal/thermal_zone0/temp". But the following paths do not exist on Armbian 23.05.1 Bookworm with Linux 6.1.30-rockchip64: /etc/armbianmonitor/datasources/soctemp /sys/devices/virtual/thermal/thermal_zone0/temp Running armbianmonitor -M, also does not show the temp: Time CPU load %cpu %sys %usr %nice %io %irq C.St. 22:29:52 408 MHz 0.02 0% 0% 0% 0% 0% 0% 0/6

• 0

  Reputation Points

• 5 replies
• 8.3k views

kolsi

October 6, 20233 yr

I thought it would be easy, but I am now turning in circles, so I am asking here. I have a working system booting on NVME (when no SD card inserted), with two partitions nvme0p1 (256Mb) and nvmeop2 (40Gb) I would like to clone my working system on a SD card. How shall I proceed? I am not asking details instruction, only the rough path I should follow (e.g. dd partitions, tune2fs ......). PS: I thought it would be easy, but whatever I do, the system keep taking /boot on the nvmeop1, so I really struggle to boot on the /boot of the SD card

• 0

  Reputation Points

• 4 replies
• 5.7k views

Tony3

March 18, 20233 yr

The code being compiled is the latest mainline. My compile command: ./compile.sh build BOARD=rock-5b BRANCH=vendor BUILD_DESKTOP=yes BUILD_MINIMAL=no DESKTOP_APPGROUPS_SELECTED= DESKTOP_ENVIRONMENT=gnome DESKTOP_ENVIRONMENT_CONFIG_NAME=config_base KERNEL_CONFIGURE=no RELEASE=noble ENABLE_EXTENSIONS=mesa-vpu It has not been compiled successfully and is stuck here. I am in China and have used a VPN. Sometimes it compiles successfully, but after installation, the 3D acceleration feature is not detected. In the GNOME settings, it shows as LLVM software rendering. Installing 3D extension packages [ mesa-vpu ] [🚸] WARNING: SDCARD /var/cache/a…

• 0

  Reputation Points

• 7 replies
• 5k views

RND

March 19, 20251 yr

The apt source is always overwritten by the cache source when modified. How can I modify this cache source. How can I modify this cache source?? help help

• 0

  Reputation Points

• 1 reply
• 2.2k views

Werner

August 29, 20251 yr

due to network limitations， how to compile Ubuntu 22.04 Gnome OS image in offline mode, build.sh need to download many debs，can I download them in advance，then install them locally. I have already downloaded kernel and uboot.

• 0

  Reputation Points

• 1 reply
• 1.7k views

laibsch

November 5, 2025Nov 5

I want to change the default display wallpaper, in order to be more nice!!! for "desktop gnome"： How to configure and appoint the default wallpaper for desktop display in build ??? Please help tell me the location！！！thank

• 0

  Reputation Points

• 1 reply
• 1.9k views

Werner

September 7, 20242 yr

hi，Kind hearted people ubuntu22 gome desktop How to configure the default settings of non-stop screen and non automatic screen lock？？ I tried to execute: sudo systemctl mask sleep.target suspend.target hibernate.target hybrid-sleep.target it can only solve the problem of not entering sleep mode！！！ But the screen will still go black, So how to set the default black screen never??? help ,help

• 0

  Reputation Points

• 5 replies
• 4.2k views
• 2 followers

IBV

May 14, 20251 yr

Hi, I have two rockpro64 boards. One board runs Debian buster with a slightly extended ayufan 5.4.0-rc1 kernel where as the other runs a Armbian (Debian) buster with the current project supplied 5.4.0-rc1 kernel. On the Debian on I have installed the nice ats solution (https://github.com/tuxd3v/ats#install) On the Armbian one the fan is running all the time. I tried to install ats there as well but I failed. Also I found that basically the /sys/devices/platform/pwm-fan/hwmon is not there, only upto pwm-fan I have. Is there some module I need to load or compile into the kernel to get ats working on the Armbian base…

• 1

  Reputation Points

• 79 replies
• 49.6k views
• 3 followers

soerenderfor

December 5, 20205 yr

We are looking at replacing the raspi3b+ with the tinkerboardS (rockchip 3288) in an embedded system, running armbian (bionic-4.19). Initial tests show that OS stability, board performance and form factor make the tinkerboardS a good substitute for the raspi. However, one issue we have run into is a conflict with pin 32 of the GPIO which is used by the hostboard for managing output devices. We have tried to turn off serial2 by removing the UART2 overlay and adding 'console=display' in /boot/armbianEnv.txt and also disabling & masking serial-getty@ttyS2.service but that hasn't stopped pin 32 from being chatty when connected to the hostboard. Is…

• 0

  Reputation Points

• 5 replies
• 6.3k views

Igor

May 12, 20197 yr

hi, How to download armbian games？？

• 0

  Reputation Points

• 3 replies
• 3k views

lay

September 7, 20242 yr

Hello. Is it possible to enable OV13855 camera on OPi5 with the latest armbian image? If yes, how do it? Thanks!

• 0

  Reputation Points

• 4 replies
• 7.9k views

Roman Aliev

June 6, 20251 yr

Can you tell me how I'm able to enable PWM? I'm not able to see any of them in the armbian-config overlay management

• 0

  Reputation Points

• 1 reply
• 2.5k views

Werner

March 28, 20251 yr

I am using Orange Pi 5 Plus with eMMC. I tried to install a program I need, but an error occurred saying that installation was not possible because SecureBoot was disabled on the system. So I need to enable SecureBoot, how do I do that? Thank you.

• 0

  Reputation Points

• 1 reply
• 3.8k views

Werner

July 2, 20242 yr

I am running an unmodified Server version of Armbian Linux v6.12 (Ubuntu 24.04) on an Orange Pi 5 Plus. I need to play sounds using the headphone jack on my SBC. Unfortunately the ES8388 sound chip is not recognized, the aplay -l output is as follows: **** List of PLAYBACK Hardware Devices **** card 0: Analog [Analog], device 0: fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0 [fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0] Subdevices: 1/1 Subdevice #0: subdevice #0 The correct output on desktop systems should like this (and it was like this on Desktop Armbian). What should I do to enable the ES8388 sound chip while staying on a server OS? …

• 0

  Reputation Points

• 10 replies
• 8.3k views
• 1 follower

Hooutoo

May 30, 20251 yr

Hello, currently on Rock5B running Armbian 24, I am not seeing the U-Boot output logs during UART debugging. Where in the source code can I enable this? Thank you.

• 0

  Reputation Points

• 3 replies
• 3.6k views

eselarm

November 29, 20241 yr

Hi. I have Rock Pi S0 boards that I install in an enclosure. It works, but it is conceivable that some critical bug or change with the image is discovered in the future so that customers later need to flash a new image to the emmc. But for them to do this, they would have to open the enclosure and locate the maskrom button, very inconvenient. Is there a way to trigger rebooting into maskrom from software instead of pushing the button? Apparently this is possible on the official radxa OS image by running command "reboot loader" instead of just "reboot", but not on armbian it seems. After investigating I see linux patches made by the rockchip team for kernel modu…

• 0

  Reputation Points

• 4 replies
• 7.1k views
• 1 follower

grixm

September 1, 20251 yr

I was happy to find the Orange pi 4 armbian; it ignores raspbian an ubuntu images on sd and boots into android from its EMMC instead. The pi is an orange 4 LTS with 3gb RAM and 16gb EMMC. I have a 2tb crucial SSD attached through the usbc port. It is powered by a 4A supply through the DC port. it's purpose is to be a dedicated mythtv back end; it is wired by ethernet but also has wifi active. armbian-hardware-monitor.log is at https://paste.armbian.com/axayequliz it isn't showing up as a disk, as near as I can tell: the first is the EMMC, I believe, and the second my sandisk car…

• 0

  Reputation Points

• 1 reply
• 3k views
• 1 follower

dochawk

February 11, 20233 yr

hi, ubuntu22 gome desktop How to fix USB sound card with card1 identifier 1

• 0

  Reputation Points

• 2 replies
• 2.3k views

lay

May 23, 20251 yr

i am taping in the dark here and in need of some help. i am running openhab on armbian 23.8.1 server and i need to get audio out on 3.5 jack for alerts. openhab has only two options system speaker and web audio. web audio plays on client like browsers using pulse audio. But if i use system speaker nothing comes out. What can i do to get sound on 3.5mm out on opi? is it even possible? i have this but this is also where my knowlege ends so help needed. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: rockchipdp0 [rockchip-dp0], device 0: rockchip-dp0 spdif-hifi-0 [rockchip-dp0 spdif-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card…

• 0

  Reputation Points

• 2 replies
• 3.1k views

Dim3nt0

January 23, 20242 yr

ubuntu22 gnome desktop Hi, may I ask how to install Google Chrome

• 0

  Reputation Points

• 1 reply
• 4.7k views

Igor

November 26, 20241 yr

Hello, Some weeks ago, I installed the kinetic version. It was rooted on the nvme drive and was working decently. After some explanations on this forum, I decided to install the LTS version. I burned a new SD card, inserted it and powered on. I was never prompt about where to install the system. After installation, the df command shows that the system is installed on the sd card. I can see nvme partitions in /dev but they aren't mounted. nvme is partitionned in two parts : one for the system, the other one is crypted and dedicated to data. How should I do? Thanks Julien

• 0

  Reputation Points

• 4 replies
• 8.5k views

VolkerW

March 1, 20233 yr

I want to install jellyfin on my OrangePi 5 Plus and need OpenCL to enable HDR-SDR mapping. I tried to follow the instruction on Jellyfin's official website: Rockchip VPU | Jellyfin However, I'm stucked on the step of installing OpenCL. I also tried this: Install OpenCL on Debian and Ubuntu and Armbian for Orange Pi 5 RK3588 But no luck either. Both instruction led to broken hardware acceleration in chrome and failing to start kernal in Jellyfin. Logs from ffmpeg: sudo /usr/lib/jellyfin-ffmpeg/ffmpeg -v debug -init_hw_device rkmpp=rk -init_hw_device opencl=ocl@rk Applying option init_hw_device (initialise hardware device) with argu…

• 0

  Reputation Points

• 3 replies
• 6k views
• 1 follower

ozacas

May 11, 20251 yr

Help me out, please. Begginer

• 1

  Reputation Points

• 1 reply
• 3.8k views

Igor

December 4, 20241 yr

Hi, I would like to use my usb wifi adapter from my old Raspi 3. `lsusb` shows: `Bus 007 Device 002: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter` `ip a` shows: ``` 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 76:ac:9a:1c:50:76 brd ff:ff:ff:ff:ff:…

• 0

  Reputation Points

• 6 replies
• 5.2k views

Gullik

September 20, 20233 yr

I am trying to compile a new kernel in order to support some satellite receiver tuner (from TBS). I did that successfully (In February 2023) on Orange Pi 5 with Linux kernel 5.10.110, but I am struggling doing it with Orange PI 5 Plus with Linux 5.10.160 (jammy). Basically I would like to turn as Modules lots of CONFIG_VIDEOBUF2_*, in order to replace the modules with the ones compiled separately (that I know are working fine with my TBS USD card). These are my issues: - I do not manage to set separately those CONFIG_VIDEOBUF2_* through the menu config. - Thus I tried to set the whole "multimedia support" as a module and go…

• 0

  Reputation Points

• 3 replies
• 2.4k views

Tony3

September 17, 20233 yr

Kind people： How to modify the default swap partition size in the configuration file and compile the firmware？？ help help

• 0

  Reputation Points

• 2 replies
• 2.9k views

lay

May 22, 20251 yr

How to modify the device name of a wireless network card? wlan0-> custom Gnome ubuntu22.04 help....

• 0

  Reputation Points

• 1 reply
• 1.9k views

Werner

October 13, 20241 yr

I followed a guide to install a system on my Rockpro64 but something happened where I had to reinstall it. However, when I reflashed the ubuntu server image and tried re-installing the system it got an error pertaining to one of my disk volumes. So I'm wondering how to re-format and remount and redo the LVM volume my SSD. Any help or tips would be greatly appreciated!

• 1

  Reputation Points

• 17 replies
• 8.9k views

kkdao

September 1, 20206 yr

Hello, I'm planning on running a k3s cluster with Rook storage with a few of the Orange Pi 5 that I got. A prerequisite for rook however is RBD module. I've been able to recompile the kernel including RBD support, however I've been unable to get the device to boot from the new kernel. Rebooting after kernel has been built and installed still reports Linux 5.10.110-rockchip-rk3588. Any help would be appreciated. I've since wiped the boxes clean and have a fresh install booting from SSD with the OS installed on the NVMe attached so I will be able to provide any information required. Thanks!

• 0

  Reputation Points

• 7 replies
• 5k views
• 2 followers

javierin

May 23, 20233 yr

Starting a new thread after this one solved my question: https://forum.armbian.com/topic/15044-how-to-re-format-and-remount-and-redo-lvm-volume-on-ssd/?tab=comments#comment-107672 but taking care of those things wasn't the root cause. it turns out the drive wasn't unmounted cleanly after accidentally unplugging the power cable from the board. I had a drive setup using: pvcreate /dev/nvme0n1 vgcreate rockpro64 /dev/nvme0n1 lvcreate -n <name> -L 500g rockpro64 then i formatted like this: mkfs.ext4 /dev/rockpro64/name but then i accidentally unplugged the power source while i got my system up and running it wasn't cleanly unmounte…

• 0

  Reputation Points

• 0 replies
• 2.4k views

kkdao

September 1, 20206 yr

How to reset the armbian system and restore the initial configuration operation

• 0

  Reputation Points

• 5 replies
• 5.6k views
• 1 follower

lay

May 16, 20251 yr

I am trying to build the kernel with the standards scripts, but directly on my orange pi 5. The build is stopping at some point because of a Warning issued by the compiler (this is the default behaviour for the compiler who does not tolerate any warning by default). (Some functions in the C code are depreciated, thus a warning is issue) How can I set the CFLAGS so that the kernel build takes it into account during compilation? Thanks.

• 1

  Reputation Points

• 7 replies
• 4.2k views

Tony3

February 8, 20233 yr

Hi, I have orange pi 5. I searched all over internet for information how to set on startup/power on GPIO pins behavior, but i cannot find anything. Most of GPIO pins are set to IN mode 1. Sadly I need them to output mode 1. I am scared something could burn this way since i set them to though wiringPI after kernel boot sequence is complete. Can some one give information how I can set them up at earlier point when I power on the board? I found that DTB/DTS file could do it. But there is no clear information / pin addresses I should set. Thanks in advance! Regards!

• 0

  Reputation Points

• 0 replies
• 1.9k views
• 1 follower

David Parushev

February 15, 20242 yr

Hi, The release notes for Armbian 23.11 state, under Key Improvements in This Release, "Mainline Kernel for RK3588 with experimental HDMI support." I am currently running the default 5.10.160-legacy-rk35xx kernel If I wanted to switch to and try out the mainline kernel for RK3588 with experimental HDMI support, would I do something like this: sudo apt install linux-image-collabora-rockchip-rk3588 After testing, If I want to rollback to the default legacy kernel, what are the steps involved? Apologies if there are instructions elsewhere that cover this. Thanks in advance for any guidance.

• 1

  Reputation Points

• 4 replies
• 6.5k views
• 1 follower

adr3nal1n27

December 5, 20232 yr

Well, I am trying to flash armbian to my board, but after I run upgrade_tool ef in mistake. I can't do anything via maskrom/loader at all wherever Windows or linux. Then I try to unbrick it via flash the "MiniLoaderAll.bin" via "upgrade_tool db" and "ul" but them don't work at all(Timeouted),How can I do with it?

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

calvin lin

March 2, 20242 yr

Hi, I really like the new option to use DT Overlays on the tinkerboard. But right now I'm struggeling a little with it: I have an old installation with 5.60 which I updated to 5.70 via apt. But the /boot/boot.cmd is still the old one and the Overlays are not working. Maybe I'm blind, but I do not see, how to update u-boot and the boot.cmd as part of it via armbian-config. Can someone point me to the right direction? Thanks, Alex

• 0

  Reputation Points

• 2 replies
• 3.4k views

deimos

January 25, 20197 yr

Is there a way to upgrade from an earlier version to 5.41?

• 1

  Reputation Points

• 8 replies
• 4.8k views

Jose Deras

March 28, 20188 yr

hi , i am using the gpio library provided by asus tinker board to work with gpio on armbian os . i am having issue with running the python script without giving sudo cmd. is there any alternative to overcome giving sudo all the time while running gpio python script or any other alternate library to use with armbian python add_event_callback.py can't open /dev/mem and /dev/gpiomem wiringPiSetup: Unable to open /dev/mem and /dev/gpiomem: No such file or directory Segmentation fault

• 0

  Reputation Points

• 4 replies
• 4.8k views

Yuvaram Singh

March 8, 20188 yr

I download the following image and encountered serious problem; Armbian_23.8.1_Orangepi5_bookworm_legacy_5.10.160_cinnamon_desktop.img.xz The problem is that after screen blank out, 8 CPU cores get near full 100% usage and OPi5 gets very hot. They all have the following htop profile. Pri NI VIRT SHR S CPU% Command 20 0 5725M 224M R 96% cinnamon -- replace

• 0

  Reputation Points

• 0 replies
• 1.2k views

oh122

October 1, 20233 yr

I have Rockchip 3288 board. As per the link: http://opensource.rock-chips.com/wiki_Graphics I checked the log at /var/log/Xorg.0.log and found glamor initialization failed. There is also log which says EGL_MESA_drm_image required, i checked x-server code and found this message lead to glamor initialization failed. Apart from these when i run glxinfo, it shows It means direct rendering is enabled. But when i run glxgears it consumed almost 18% CPU( So i think glxgear is not able to use GPU and performing all tasks at CPU). What i am to do: I have created a application which can decode H264 vid…

• 0

  Reputation Points

• 10 replies
• 12.2k views
• 2 followers

jock

September 24, 20188 yr

I'm trying to set up a DS3231 hardware clock and the system can't find the hwclock command. I installed the util-linux command as other references suggested, but the command still isn't there. Thank you

• 0

  Reputation Points

• 1 reply
• 3.4k views
• 1 follower

Werner

December 12, 20241 yr

I could not find any arm64/aarch64 MODERN, up to date, Tor browser binaries. Anything below current-stable would be considered insecure, and at a glance I couldn't find them anywhere. So I was able to compile Nightly for the latest updates as well It took 331 minutes, and failed 4 times along the way with 8GB RAM native on the device and 4GB ZFS to start. It did a SIGKILL9 on firefox-glean. Increased to 8gb, still failed until I increased ZFS to 16gb, and then even at a whopping 16gb it crashed next on GkRust for OOM/SIGKILL9 as well until increased ZFS to 32GB! 331 minutes later, it was succesful Just wondering, to save myself from future pun…

• 0

  Reputation Points

• 5 replies
• 6.5k views
• 2 followers

snow

September 7, 20251 yr

I created a deb package for my own application. How do I import it for compilation and installation?

• 0

  Reputation Points

• 1 reply
• 2.3k views

Werner

September 3, 20242 yr

Title, i just download the right version used balenaEtcher for flashing it on microssd and its stuck on blue light(booting), how i can solve it

• 0

  Reputation Points

• 1 reply
• 2k views

Igor

September 8, 20251 yr

Hi there, Just got Orange Pi 5 8GB and have no idea where to begin. I have a microSD card available, but no writer. I had the idea to boot from USB thumbstick and then write the SD card using the port on the Orange Pi 5, then I can boot from SD card. Is this possible? What image and method do I need to follow in order to boot from a simple 32GB USB Sandisk thumbstick? Thank you!

• 0

  Reputation Points

• 4 replies
• 5.3k views
• 1 follower

berin

January 29, 20233 yr

Hi. I am not complaining. I just would like to understand why I must deactivate https://ppa.launchpadcontent.net/liujianfeng1994/rockchip-multimedia/ubuntu/ if I want watching video on Youtube. If it's needed to disable this repo for watching video. I am ok. But why I can't read video with package from this repo? https://paste.armbian.com/vaxedisuda

• 0

  Reputation Points

• 0 replies
• 1.6k views
• 1 follower

olivetree

August 20, 20251 yr

Hi everyone, I’m using an ASUS Tinker Board (RK3288, 2 GB, released in 2017). Since this board is quite old and we are now in 2025 I want to run the latest stable Armbian and develop a Python application using I²C, UART, PWM, and GPIO pins. Which Armbian image and kernel branch (current or edge) is the most stable for this board? Are there any specific steps or adjustments needed due to its older hardware? Thanks!

• 1

  Reputation Points

• 2 replies
• 4.4k views
• 4 followers

jock

July 28, 20251 yr

I want to install Armbian on Nvme SSD. How do I install on SSD?

• 0

  Reputation Points

• 4 replies
• 4.7k views

Guest

February 1, 20233 yr

Hello everyone, due to a project I'm working with the Friendly Elec Nanopi R4S board for which I've to use the i2c bus to read data from a sensor. Unfortunately I've not been able to access it, since the system does not recognize it. I tried with different configurations using the /boot/armbianEnv.txt file with no results, however the i2c ports are enabled. To rule out functionality problems in the sensor, I connected it to other boards (e.g. nanopi Neo3 using Armbian) without problems. Do you have any idea what could be the cause of this problem? Thanks!

• 0

  Reputation Points

• 1 reply
• 4.4k views

mef1k

October 3, 20224 yr

I need to move my homeassistant from rpi4 to an opi5 but I have some I2C sensors connected. Had anyone any luck configuring python and gpio to work with I2C sensors? This was a bit rough a while ago and the kernel support seems much more limited compared to the rpi4 for this type of use case. Any experience?

• 0

  Reputation Points

• 4 replies
• 4.6k views
• 1 follower

martivo

August 31, 20233 yr

After updating my Orange Pi 5 I no longer can use the "opi5-i2c5-m3" overlay in /boot/armbianEnv.txt to activate and use i2c. Seems the file (or any ohter "opi5-i2c*") is gone from /boot/dtb folder. #uname -a Linux 5.10.110-rockchip-rk3588 #1 SMP Sun Apr 2 14:30:48 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux Is there a new or different procedure to activate i2c? Do I need to install a separate package for it? Or build the entire OS? Anyone else having the same issue? It does detect some i2c devices(0,10,2,6,7,9), but they don't seem to be related to the GPIO headers, prevoiusly I could also use (1,3,5). # ls -l /dev/i2c- i2c-0 i…

• 1

  Reputation Points

• 5 replies
• 7.3k views

martivo

June 2, 20233 yr

I'm using an Orange Pi 5 Plus 16GB SBC, with Armbian image (https://dl.armbian.com/orangepi5-plus/Bookworm_current_cinnamon-backported-mesa) which uses Kernel 6.12. I am trying to get a BME280 I2C sensor attached to the following pins of the 40 pins; 1 (3.3v), 3 (GPIO0C0), 5 (GPIO0B7), and 6 (GND). The BME280 sensor has the VIN wired to 3.3v (pin 1), SDA wired to SDA (pin 3), SCL wired to SCL (pin 5), and GND to GND (pin 6). The device should use address 0x76, but isn't listed under the four I2C buses found in /dev. This configuration worked fine when using the stock OrangePi 5 Plus Debian Bookworm image, but does not have I2C2 listed as a device under /dev un…

• 0

  Reputation Points

• 9 replies
• 5.8k views
• 1 follower

Robert Pace

December 29, 20241 yr

Greetings, I recently had a request about testing the I2S and SPDIF output of MiQi devices and after some fiddling on this board, it seems that the Rockchip I2S + Simple-Audio ALSA driver just output nothing on the I2S TX/RX pins, at least. So was anyone able to output sound directly through the I2S GPIO pins on any RK3288 device ? Tinkerboard devices seems to use that setup and it seems to be working, but I'd like to know if that's working through the soldered Jack or the GPIO.

• 0

  Reputation Points

• 10 replies
• 4.6k views

nitroshift

March 14, 20188 yr

Hi, I'm pretty new to this forum may be I will ask some already answered questions, but here they are: I just had a new orangepi 5 plus card and I failed to use the "buses": - I2s: didn't find anywhere how to activate it (i'm trying a dac as a soundcard). Didn't find the hifiberry-dac overlay neither (ok maybe this one is just for raspberry). - spi: I plugged a simple mcp3008 to the spi pins but can't read anything on it (i have the /dev/spidev0.0/1 and /dev/spiddev4.0/1 devices). I think I respected the rights pins. - i2c: when I activate the overlays in armbianEnv.txt, I can see a lot of messages every seconds with dmesg about rk-hdmi. Ma…

• 1

  Reputation Points

• 15 replies
• 16k views

Igor

December 10, 20232 yr

Hi everyone, I was experience some strange things with two similar devices, the first I installed in february this year, mesa v.24.x and EGL 1.4 and it was working fine The other one I installed this week and it turns out that it uses mesa v.25.x and EGL 1.5, although performance was great with most 3D apps (like glmark2) I had poor performance under sway/kitty or the retroarch menu for instance (something like 15 fps). It took me a few days to find a solution so if you have similar issues please try installing mesa with the kisak repository as it fixed my problems sudo add-apt-repository ppa:kisak/kisak-mesa -y sudo apt update sudo apt upg…

• 0

  Reputation Points

• 0 replies
• 2.6k views

dwarfman78

September 14, 20251 yr

Hi all, Is anyone here good with upbringing MIPI panels on Linux via device tree modifications? I've had an attempt with a specific LCD panel but I am not having any luck to be honest. I would love someone to kindly review my Git Diff/device tree changes for any errors. I've attached my LCD init code as well, as well as the DSI portion of the dmesg output log, as well as my schematics for the custom driver board I have designed. https://drive.google.com/file/d/18E5zOGlNpdWLrD43R7bB4N-Mf_8mQFKY/view Thank you! DSI_Debug_Log.txt

• 0

  Reputation Points

• 0 replies
• 1.5k views

StonedEdge

August 25, 20233 yr

I know this sounds strange, but I cannot get any of the images to boot. I have an R3S non-LTS + SD card. It works well with the stock images from FriendlyElec, but none of the Armbian images I tried will boot. I tried different tools to write the SD (BalenaEtcher, USBImager, Rufus), but nothing changed. When I tried to read the SD card with Armbian on my x86 laptop running Debian, the system didn’t recognize any proper partitions (maybe that’s normal, maybe not—I don’t know). But when I write an Armbian image for Allwinner NanoPi, the partitions are detected correctly. And finally, I can’t connect to the debug UART, so I can’t get any logs. I feel…

• 0

  Reputation Points

• 13 replies
• 6.8k views
• 2 followers

Vlad Kuzin

August 23, 20251 yr

Hi, i am new to single board computers and i tried almost every posible thing to make this work. DISPLAY=:0 xrandr --output HDMI-1 --brightness 0.5 and i also tried xbacklight, with no luck. Linux Debian 4.4.102-rockchip #3 SMP Fri Nov 24 19:01:14 CET 2017 armv7l GNU/Linux my xrandr output: kiosk@Debian:/sys/class$ DISPLAY=:0 xrandr Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 4096 x 4096 HDMI-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis) 640mm x 360mm 1920x1080 60.00*+ 50.00 59.94 25.00 24.00 23.98 1920x1080i 60.00 50.00 59.94 1280x1024 60.02 1280x…

• 0

  Reputation Points

• 0 replies
• 4k views

Bekim Lutolli

December 11, 20178 yr

Tried 5 diferrent microSD cards, 3 card readers, multiple redownloads on Mac and Windows. Diferrent power supplies, including 100W charger and 52pi EP-0136 direct 5v supply. No green LED, no LAN communication, no HDMI output. Everything i get is in log (via UART) Please help... i've got no more ideas. DDR Version V1.08 20220617 LPDDR4X, 2112MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB Manufacturer ID:0x1 Samsung CH0 RX Vref:32.7%, TX Vref:1…

• 0

  Reputation Points

• 5 replies
• 4.3k views
• 1 follower

DimonKyiv

February 19, 20233 yr

https://www.cnx-software.com/2017/12/07/rockchip-rk3288-to-be-phased-out-soon-gpd-xd-android-console-to-get-mediatek-mt8176-soc-4gb-ram-upgrade/ Rockchip RK3288 32-bit Arm processor was first spotted in a company presentation in the summer of 2013, before being announced – with some confusion (Cortex A12 vs A17) – at CES 2014 in January. The quad core Cortex A17 processor had then its moments of glory with inclusion in products such as Chromebooks (2015) and ASUS Tinker board SBC earlier this year. “Rockchip are phasing out sales of the RK3288”, meaning most products based on the chip will soon be phased out or upgraded to another solution. …

• 1

  Reputation Points

• 9 replies
• 8.4k views
• 1 follower

TonyMac32

December 18, 20178 yr

Hello, I would like to know more informations about this test made with the Asus XG-C100C Network Adapter or, generally, how to optimize the speed from a 10GbE PCIe Network Adapter in the RockPro64. Which version to use of Armbian and how to get that version to have so good performances? Which version of the Adapter driver to use? Were the drivers included in the Kernel or did you use the Asus driver recompiled? I would be very grateful if you will help me. Thank you.

• 0

  Reputation Points

• 1 reply
• 3.4k views

Tauro

January 21, 20233 yr

On several RockPro64 boards I experience infrequent freezes, mostly directly on boot, but also after some longer (hours, days) uptime. I use the official power adapter and no additional hardware except a PCIe adapter for an SSD, which works flawlessly when operational. When looking at the kern.log, there are quite a few errors and warnings, but comparing to a successful boot these are all also present. So I don't think they cause the freeze directly. Currently, I recorded the freeze on the latest Armbian Bionic as release just recently. FWIW, I think the same issue also occurs on the previous Debian Stretch image (had various freezes, but have not …

• 1

  Reputation Points

• 16 replies
• 10.7k views
• 1 follower

Myy

April 1, 20206 yr

Hello, unfortunatelly I post again, because of the latest problem with broken install of initramfs .... The system is unable to write it to uboot and gives the error about unsupported architecure. Every standard commands are probed, without result. it comes always the same error.

• 0

  Reputation Points

• 4 replies
• 5.1k views
• 1 follower

technik007_cz

February 1, 20251 yr

Can anyone tell me if it's possible to install renegade firmware on a Rasperry Pi build for example? Libre used to host a script for a tool that achieved this but it hasn't been updated since Buster TIA

• 1

  Reputation Points

• 5 replies
• 2.3k views
• 1 follower

0jay

November 27, 2025Nov 27

HI!! I need help. What is the correct way to install armbian? I have an odroid m1, with a nvme 2 TB. I installed armbian and also stored my files on the same disk. The problem is that one day I updated the system and also updated the kernel. This caused the system no longer boot. I tried to fix the file system but it is still corrupt. The problem is that the nvme where I have all my files is not accessible and therefore I cannot copy them to another drive. When I mount the nvme drive (with external case) on my laptop with Ubuntu, the files do not appear. Therefore, I would like to know if where is the best option to install armbian and and mantaining safe mu files. In th…

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

Fernando Castillo

July 24, 20242 yr

Hello everybody. I own a Orange Pi 5 Plus with Debian and 3 partitions: boot, root and storage (fat, ext4, ext4). Now I want to try Armbian but I don't want to overwrite the storage partition, so I shoudn't use dd to write the .img file. Ant tip to solve this situation? Thanks.

• 0

  Reputation Points

• 4 replies
• 3.4k views
• 1 follower

Jose Francisco

July 5, 20242 yr

I want to install the usb wifi/bluetooth card drivers but I keep getting an error during compilation. What to do? below code: DKMS make.log for rtl8812au-5.13.6 for kernel 5.10.110-rockchip-rk3588 (aarch64) Tue Jan 10 08:48:19 PM CET 2023 make ARCH=arm64 CROSS_COMPILE= -C /lib/modules/5.10.110-rockchip-rk3588/build M=/var/lib/dkms/rtl8812au/5.13.6/build modules make[1]: Entering directory '/usr/src/linux-headers-5.10.110-rockchip-rk3588' CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_cmd.o CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_security.o CC [M] /var/lib/dkms/rtl8812au/5.13.6/build/core/rtw_debug.o CC [M] /var/lib/dkms/rtl8812au/5.1…

• 0

  Reputation Points

• 5 replies
• 10.9k views

Fabricio Biazzotto

February 15, 20233 yr

I got a 6.1 noble minimal image installed with a latest kubuntu update to KDE 6. Was quite some work to get this all working. But some thing aren't working (e.g. audio?). 6.12 and later supports a range more peripherals. I tried the non-vendor images but no go. How do I install one of those? (Not using ROOBI, I hacked this to use my own)

• 0

  Reputation Points

• 2 replies
• 2.9k views
• 2 followers

Jurgen.Schober

June 2, 20251 yr

Hello, I tried to install the RTL8821CE card on Orange Pi 5 Plus, but only the Bluetooth is on, the wifi not working. Which driver i should use? I am using Armbian 24.2.1 Jammy with Linux 5.10.160-legacy-rk35xx here is the dmesg of admin@orangepi5-plus:~$ nmtui admin@orangepi5-plus:~$ dmesg | grep 8821 [ 5.588211] pci_bus 0003:30: root bus resource [mem 0x9c0000000-0x9ffffffff pref] [ 8.482106] rtw_8821ce 0002:21:00.0: enabling device (0000 -> 0003) [ 8.493940] rtw_8821ce 0002:21:00.0: Firmware version 24.11.0, H2C version 12 [ 8.534600] rtw_8821ce 0002:21:00.0: rfe 6 isn't supported [ 8.534719] rtw_8821ce 0002…

• 0

  Reputation Points

• 1 reply
• 3.1k views

ozacas

September 12, 20242 yr

I am attempting to install the file Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop.img from https://www.armbian.com/orangepi-5/ but the installation hangs at the point where the root password should be entered. The same happens with the file Armbian_23.02.0-trunk.0112_Orangepi5_jammy_legacy_5.10.110_minimal.img. If i use the file Armbian_22.11.3_Orangepi5_jammy_legacy_5.10.110_cinnamon_desktop.img from the Github archive the installation completes. I have tried to raise a bug but the only solution for not booting are hardware and the installation has not progressed far enough to enter any commands. Any assistance welcomed.

• 0

  Reputation Points

• 1 reply
• 1.7k views

Werner

January 22, 20233 yr

Hello Developers, I ran into some issues installing the latest release on an Orange Pi 5 Plus. The images I downloaded are as follows: Armbian_24.11.2_Orangepi5-plus_noble_current_6.12.0_kde-neon-kisak_desktop.img.xz Armbian_24.11.2_Orangepi5-plus_noble_vendor_6.1.75_gnome-kisak_desktop.img.xz The KDE version will install and boot from the 256GB emmc drive, however it only works if there is a 4K HDMI monitor attached to HDMI1, I was not able to get it to display on a 1920x1200 HDMI monitor nor a USB connected or HDMI connected portable display (2560x1440). The Gnome version will boot with any of those 4 types…

• 0

  Reputation Points

• 7 replies
• 8.6k views

Werner

January 10, 20251 yr

I am trying to install Ambian on to the BananaPi-M7 to eMMC using option 6. there is no option for NVME / M2 SSD. I had a failed install as the uSDCard image was 256GB larger than the eMMC, so it balked. I tried a 128GB uSDCard, followed by a 64GB uSDCard, but got the same error each time even on the 64GB one. I seem to have two partitions on the eMMC, mmcblk0boot0, and mmcblk0boot2 now,. I am not sure if they were on the boards eMMC originally or what the boot sequence for the board is If the Masked ROM tries to boot the uSDCard if present and if that fails it boots the eMMC ? Do I clear mmcblk0 and try again with the 64GB uSDcard ? Or is mm…

• 1

  Reputation Points

• 55 replies
• 25.5k views
• 1 follower

AaronNGray

December 15, 20241 yr