Rockchip

Hello, I'm using a RockPro64 boards inside one of my projects and I just noticed an issue related to the reset process. When pushing the reset button, the boards hangs in a reset loop. Using the oscilloscope, I found that the reset signal (OTP_OUT_H) is toggled every 330ms by the CPU and the only way to get it back to work is to power off the board, wait a few seconds, and power it back. The same issue is found if, after a working boot, a quick power cycle is performed. I tried disconnecting everything from the board but still, when pushing the reset button, the boards hangs in a loop condition (as if it’s constantly crashing at boot). …

• 0

  Reputation Points

• 5 replies
• 4.7k views

martinayotte

November 8, 20196 yr

I'm trying to use an SPI driven TFT display on the orange pi 5, but I'm stuck on enabling SPI in the first place. Looking at the pinout of the orange pi 5 in its manual, it appears that SPI4...M0 is the only bus broken out to the pins. However, enabling "rk3588-spi4-m0-cs1-spidev" in the armbian-config menu does not seem to do anything, as no /dev/spi device exists after a reboot. Enabling any of the other spi hardware functions seems to work just fine, creating a /dev/spi device as expected, but none of the other spi busses are accessible through the pin header. I'm on Armbian 23.8.1 (image: Armbian_23.8.1_Orangepi5_bookworm_legacy_5.10.160.img). Has anyone used SPI on t…

• 1

  Reputation Points

• 3 replies
• 6.6k views
• 1 follower

Josh Blackburn

October 15, 20232 yr

I am interested in hardware video support and wether ffmpeg has hardware support on the RK3588 and Mali G610MC4 GPU. And was wondering if someone whould be interested in giving me the output of a few tests for me please ? ``` ffmpeg -hide_banner -encoders ``` ``` ffmpeg -hide_banner -decoders ``` ``` ffmpeg -hide_banner -hwaccels ``` Many thanks in advance.

• 0

  Reputation Points

• 2 replies
• 4.3k views

AaronNGray

August 30, 20242 yr

I have installed the recently released `Desktop images with Armbian Linux v6.10` image (24.8.1, Debian Bookworm, with the Cinnamon desktop) on an OrangePi5 and I'm happy the HDMI support included has finaly enabled the video to my 1080p display. However, my previously supported WiFi adapter is not recognized in this version - it worked with the vendor (5.10) kernel which I used with last year's OrangePi5 image, but how it seems the driver is not installed with 6.10. The WiFi adapter is connected via USB and it's listed as Realtek Semiconductor Corp. RTL8812AU 802.11a/b/g/n/ac 2T2R DB WLAN Adapter. Now, there are a few DKMS/out-of-tree drivers that I could inst…

• 1

  Reputation Points

• 4 replies
• 7.7k views
• 2 followers

mitu

September 10, 20242 yr

Hi. I have RockPi E v1.21 and I found, that I'm not able to boot image with new kernel 6.12 (tried minimal images 25.2.1 and 24.11.1, USBImager and Balena Etcher, 3 SD cards, different power supplies). With image 24.8.3 it boots normally. Also I found, that after upgrading 24.8.3 to kernel 6.12 the RockPi boots, but Ethernet doesn't work (even LEDs are dead). Another thing which I notice is, that I didn't find any option to disable kernel upgrades, but what I googled, it should be present in armbian-config->system->kernel->Y203. But this Y203 option is missing. Here is successful boot log of 24.8.3: https://paste.armbian.com/ixuvimofis.sql …

• 0

  Reputation Points

• 15 replies
• 7.8k views
• 2 followers

Benik3

May 26, 20251 yr

Hi, I am currently using rock-5-itx to setup a NAS. Everything is working fine. uname -a: Linux amberbyte 6.1.75-vendor-rk35xx #1 SMP Thu Nov 28 03:16:11 UTC 2024 aarch64 GNU/Linux Now, I wanted to update RKNPU version from 0.9.7 to 0.9.8. So, again I recompiled the image with the updated drivers. Using Pi-imager flashed it onto an SD card. When I tried to boot I am getting the following error message from the serial output: ./compile.sh build BOARD=rock-5-itx BRANCH=vendor BUILD_DESKTOP=no BUILD_MINIMAL=yes EXPERT=yes KERNEL_CONFIGURE=yes RELEASE=bookworm DDR 9fffbe1e78 cym 24/02/04-10:09:20,fwver: v1.16 LPDDR5, 2400MHz channel[0] BW…

• 0

  Reputation Points

• 1 reply
• 2.4k views

Werner

May 20, 20251 yr

I had use QML to made some soft, and when i move those soft to Tinkerboard, it's Incredibly slowly... have any idea to fix this? did tinkerboard had open gpu acceleration? do i must change back to use QtWidget?

• 0

  Reputation Points

• 0 replies
• 2.2k views

aitek

November 12, 20187 yr

Hi all, I just bought TinkerBoard S and I downloaded Armbian Stretch 4.19 (tried both with and without desktop ) and I tried to boot. But no luck I was waiting for few mins but nothing. I also tried Armbian Strech 4.4 but also nothing. Am I missing something here? Original TinkerOS work without any issue Thank you for any advice/help

• 1

  Reputation Points

• 13 replies
• 20.3k views
• 1 follower

dragonlost

December 13, 20196 yr

I was using the nightly version 23.02.2 but now the repos have changed. How can I update to the new nightly repo os ? https://github.com/armbian/os # PLEASE DO NOT EDIT THIS FILE BOARD=odroidm1 BOARD_NAME="ODROID M1" BOARDFAMILY=rk3568-odroid BUILD_REPOSITORY_URL=https://github.com/armbian/build BUILD_REPOSITORY_COMMIT=1a8daf0 VERSION=23.02.2 LINUXFAMILY=rk3568-odroid ARCH=arm64 IMAGE_TYPE=nightly BOARD_TYPE=wip INITRD_ARCH=arm64 KERNEL_IMAGE_TYPE=Image BRANCH=edge Thanks !

• 0

  Reputation Points

• 2 replies
• 3.7k views

j0ta

March 1, 20233 yr

Degin: MounlAng root Tile syslel ... Degan: munning escrapusr cucad-lop ... uonc. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. done. Geve up waiting for root file system device. Cowmon problems: ⁃ Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! UUID=db80a2ac-ec37-4fda-91db-92604becfcce does not exist. Dropping to a shell! BusyBox v1.30.1 (Ubuntu 1:1.30.1-7ubuntu3.1) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) …

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

TheFlash

October 23, 20241 yr

Hi can anyone advise if they have come accross this issue. so somehow HDMIRX seems to be the hdmi input controller starts to freak out for no reason there is nothing plugged into it EVER and will randomly start to outpur this to console im thinking maybe the HDMIRX is faulty and want to remove it, I have tried removing it removed the DTB , decompiled and edited and removed it from DTB, tied to blacklist it but with no effect it does not stop spamming and the device [ 89.603095] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_phy_register_write wait cr write done failed! [ 89.613765] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_phy_register_write wa…

• 0

  Reputation Points

• 1 reply
• 2.5k views
• 1 follower

Werner

March 14, 20251 yr

A few days ago I had an issue with a successfully running Armbian installation running from the NVME of my Orange Pi 5 that suddenly developed an issue with nothing being shown on my TV. So after seemingly not being to identify the problem, I started again, wrote the image to an SD card and then moved the installation to the NVME drive using armbian-config utility. So now that I have a set-up that works again, I want to instigate a more belt and braces approach and create an image of the NVME installation using GZIP to compress the image file and decided to use the DD option from terminal. Having tried well over a hundred different comb…

• 0

  Reputation Points

• 3 replies
• 3.3k views
• 1 follower

laibsch

July 7, 20251 yr

If any of you have experienced skipping and popping when seeking with vlc, you can try setting the audio sink to ALSA and one of the rockchip-es8316 options. That will smooth out the audio playback BUT you will quickly discover that anything pulseaudio related is locked out of using the soundcard while vlc is up. Instead, try this. Set vlc audio back to pulseaudio (or automatic, seems to map to the same thing) and then change these two lines in /etc/pulse/daemon.conf: -; default-sample-rate = 44100 -; alternate-sample-rate = 48000 +default-sample-rate = 48000 +alternate-sample-rate = 44100 Restart pulseaudio with systemctl --user …

• 0

  Reputation Points

• 1 reply
• 2.3k views

Popolon

December 5, 2025Dec 5

Hi there! I am trying to set up communication between an Attiny85 and my RockPro64 over UART (running Armbian, kernel `Linux rockpro64 5.8.1-rockchip64 #20.08 SMP PREEMPT Mon Aug 17 08:17:08 CEST 2020 aarch64 aarch64 aarch64 GNU/Linux`). The issue is that I can't connect to the serial port: rock64@rockpro64:~$ sudo picocom -b 115200 /dev/ttyS4 picocom v3.1 port is : /dev/ttyS4 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no hangup is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is …

• 0

  Reputation Points

• 5 replies
• 6.3k views
• 1 follower

antonlyap

October 4, 20206 yr

Hello, After NanoPi R4S reboot, ethernet interface `enp1s0` disappeared. I tried soft reboot for several times but failed. If I shutdown the board and power plug out/in again, then `enp1s0` appears. I tested it several times and 100% same results. Any idea please? wg* is for vpn. please ignore them.

• 1

  Reputation Points

• 14 replies
• 8k views
• 1 follower

Igor

October 29, 20223 yr

I would love to use Armbian Build to construct a Debian 12 Bookworm images with KDE Plasma as the windows manager. I note that KDE Plasma isn't an option in the armbian builder. I have no problem building with XFCE or Cinnamon.

• 0

  Reputation Points

• 3 replies
• 4.2k views
• 1 follower

Robert Pace

April 27, 20251 yr

The apt source is always overwritten by the cache source when modified. How can I modify this cache source. How can I modify this cache source?? help help

• 0

  Reputation Points

• 1 reply
• 2.2k views

Werner

August 29, 20251 yr

https://wiki.friendlyarm.com/wiki/index.php/NanoPi_R4S I am really excited about this board. https://www.cnx-software.com/2020/11/12/nanopi-r4s-headless-rk3399-sbc-features-up-to-4gb-ram-dual-gigabit-ethernet-usb-3-0-ports/ The first comments below this blogpost are also not so bad besides the fact that USB-C is power-in only.

• 1

  Reputation Points

• 41 replies
• 34.7k views
• 7 followers

dolphs

July 24, 20224 yr

Hi everyone, Has anyone been able to get gpu hardware acceleration to do encoding/decoding on Jellyfin on the orange pi 5? Thank you

• 1

  Reputation Points

• 1 reply
• 4.2k views
• 1 follower

royk

October 15, 20232 yr

Installed: Armbian_23.11.1_Orangepi5-plus_bookworm_edge_6.7.0-rc1 The analog device is visible, but there's no sound from the headphone jack. The hdmi device is not visible. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Analog [Analog], device 0: fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0 [fe470000.i2s-es8328-hifi-analog es8328-hifi-analog-0] Subdevices: 1/1 Subdevice #0: subdevice #0 There is no sound when I play a test file: aplay -D hw:0,0 /usr/share/sounds/alsa/Noise.wav Playing WAVE '/usr/share/sounds/alsa/Noise.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Mono apl…

• 0

  Reputation Points

• 4 replies
• 5.3k views
• 2 followers

Werner

January 24, 20242 yr

Hello, I'm using a rock pi e ver 3.0 with armbian 24.8.3: I would like to drive the state of a gpio, that of pin 7 or gpio 100: I'm not an expert and I tried to use the GPIOD libraries for python but I couldn't do anything because I get errors; from the command line through the gpiodetect command it seems to me that the chipset is recognized and I see some lines and the status of the gpios but I cannot change the status of these. Am I going in the right direction? Are there other methods to drive these GPIOs? Thank you in advance.

• 0

  Reputation Points

• 3 replies
• 3.2k views
• 1 follower

Werner

December 6, 20241 yr

I have an encrypted root partition, and on booting, it asks me for the passphrase to decrypt it. This was shown on the screen when I was using the 6.6.47 kernel, but on the 6.12.11 kernel, nothing is shown on the screen at all until I've successfully typed the passphrase and it's started booting. Here's the armbianmonitor -u output for the working 6.6.47 kernel: https://paste.next.armbian.com/suporamoqe And here's the output for the not-quite-so-working 6.12.11 kernel: https://paste.armbian.de/cuxaxoweci This isn't a huge deal for me, since I usually close my eyes while typing the passphrase anyway, but it means I have to guess when it…

• 0

  Reputation Points

• 0 replies
• 2k views
• 1 follower

Tim Makarios

January 26, 20251 yr

Hello, I just got a wifi 7 adapter (QCNCM865) and I was thinking the ath12k driver was available starting from kernel 6.13, I'm running the edge kernel 6.16.4 and the ath12k driver is failing to load and I can't find any wireless drivers in /usr/lib/modules/6.16.4-edge-rockchip64/kernel/net/wireless. Do I need to rebuild the kernel with the ath12k driver? or is there a kernel version available with that driver? Thanks for your help!

• 0

  Reputation Points

• 2 replies
• 2k views
• 1 follower

mido_00

October 23, 2025Oct 23

Hi team, I am on the latest vendor release of gnome installed via armbian installer. Kernel is linux-image-6.1.115-*-rk2410. When I look for audio drivers I do not see card 3: rockchiphdmiin [rockchip,hdmiin], device 0: fddf8000.i2s-dummy_codec hdmiin-dc-0 [fddf8000.i2s-dummy_codec hdmiin-dc-0] Subdevices: 1/1 Subdevice #0: subdevice #0 I got the board very recently and the forum is a little mesay about the hdmi rx functionality. It would be a great help if anyone can help me out on this, let me know if i am missing anything.

• 0

  Reputation Points

• 0 replies
• 759 views
• 1 follower

hyperwolf

May 16May 16

Hello, I am trying out the latest Armbian image on the Renegade board and after several hours i still do not the analog audio to work. Only the HDMI output is found and used. With the Ubuntu images provided by Firefly, the analog audio works fine, so we can exclude that it may be a problem with the hardware. I have seen in this forums such descriptions for other boards with the 3328 CPU, but from my understanding do that solutions not fit for the Renegade. May somebody provide me a hint, how to activate the analog output? Here you can find the Armbianmonitor output: http://ix.io/1vHd Here you can find inform…

• 0

  Reputation Points

• 10 replies
• 6.5k views

c0rnelius

December 18, 20187 yr

This is a last-ditch effort to figure out how we can continue to build our project on top of Armbian. Goal We are building an appliance on the RockPro64 board, with eMMC and an PCIe SSD attached, using a custom-built Armbian Ubuntu 18.04 image with extensive post-configuration (packages, appliacations, overlayroot...) within the boot process. The image is then processed by Mender to create a true dual-root filesystem over-the-air update system with fallback (we invested a lot of resources to extend Mender for Armbian and RockPro64). This build process works perfectly and is exactly what we need. Issue The reliability, however, is bad. In …

• 1

  Reputation Points

• 12 replies
• 7.8k views
• 2 followers

soerenderfor

October 18, 20205 yr

Has anyone tried GPIO access on the latest armbian? I noticed that the custom wiringPi https://github.com/orangepi-xunlong/wiringOP.git doesn't compile on armbian. It is missing GPIO constants.

• 0

  Reputation Points

• 5 replies
• 8.1k views

mrkev

January 26, 20233 yr

Hello all! In Orange Pi OS latest image all works well EXCEPT it keeps launching apps in a stupid bordered window that has a huge obnoxious bar at the top with 2 absolutely useless buttons, a window to full screen option and the X button How do I hide this stupid thing? It's blocking the whole top of my screen and cutting off part of my TiviMate Pic here https://imgur.com/a/8uo8WrM

• 0

  Reputation Points

• 2 replies
• 2.1k views
• 1 follower

compent

March 2, 20233 yr

The problem persist on both Armbian 23.8 bullseye and Armbian 23.11.0-trunk.107 Bullseye After change it via armbian-config It stays the default cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 1 2 3 CPUs which need to have their frequency coordinated by software: 0 1 2 3 maximum transition latency: 149 us. hardware limits: 408 MHz - 1.99 GHz available frequency steps: 408 MHz, 600 MHz, 816 MHz, 1.10 GHz, 1.42 GHz, 1.61 GHz, 1.80 GH…

• 0

  Reputation Points

• 2 replies
• 5.5k views

j0ta

September 28, 20233 yr

With Debian Bookworm on BananaPi-M7 when Viewsonic VX3276-2K-MHD WQHD 2560x1440 the display is the wrong resolution only supporting upto 1920x1080 or 2560x1080 for ViewSonic 32” monitor config. It also fails to resync when turned off and on again or another source is selected on and the BPi-M7 is reselected, resulting in a flickering white backgound. Armbian_25.2.1_Bananapim7_bookworm_vendor_6.1.99_xfce_desktop.img with apt-get update & apt-get upgrade Armbian 25.2.3 bookworm 12 Linux bananapim7 6.1.99-vendor-rk35xx Ubuntu works fine and supports the Viewsonic VX3276-2K-MHD WQHD on 2560x1440 for this but has a display area i…

• 0

  Reputation Points

• 2 replies
• 2.7k views
• 1 follower

amazingfate

May 7, 20251 yr

Hi, has any of you some experience connecting a Hifiberry Amp+ to a Tinkerboard - on Hifiberry pages this is now a possible connecting but I miss a howto and would really appreciate a quick start on this. Have previously succeed with Raspberry 3 and IQaudio - but intend to take a step further and do a project being more than just an amplifier. After testing several OS I have to admit Armbian has become my favorite and it is within this OS I hope to achieve this.

• 0

  Reputation Points

• 1 reply
• 3.4k views

Andrius ok

February 23, 20188 yr

Hello. Has anyone had success with setting up the onboard wifi on the Tinkerboard without the network manager? I have tried using wpa_supplicant to connect but not having any success. Here is what (I know works on an Intel Compute Stick running Ubuntu 16.04) I've tried: wpa_passphrase SSID password >> /etc/wpa_supplicant.conf wpa_supplicant -i wlan0 -c/etc/wpa_supplicant.conf -D nl80211 -B dhclient wlan0 dhclient just keeps retrying and goes no where, I don't get an IP address I can connect to my network using the Network Manager no problems, just can't figure out a way to get it to work with the network manager disable…

• 1

  Reputation Points

• 9 replies
• 19.2k views

freak

March 21, 20188 yr

Hallo! Habe Armbian 22.08.6 Jammy with Linux 5.15.74-rockchip mit Desktop auf "Asus Tinker Board Rev. 1.2" laufen, aber leider bekomme ich per HDMI keine stabile Verbindung. HDMI Kabel bereits getauscht (geht mit anderen Geräten einwandfrei) auch Montor getauscht (geht mit anderen Geräten auch einwandfrei). Auflösungen und Framerates habe ich durchprobiert - fehlerbild aber immer das gleiche; Bild bleibt bestenfalls ein paar sekunden ein, dann geht es wieder aus für ein paar Sekunden und das setzt sich fort. Hab ein bisschen hier im Forum recheriert und sehe das man ein "armbianmonitor -u" ausführen soll und im Forum posten: https://…

• 0

  Reputation Points

• 1 reply
• 2.6k views
• 1 follower

Werner

October 25, 20223 yr

does displayport over usb-c dock work for you? It doesn't for me neither on 5.15 nor on 6.1.

• 0

  Reputation Points

• 4 replies
• 4.4k views
• 1 follower

Werner

December 9, 2025Dec 9

@SteeMan the thing is I have a RockPro64 and the only way to get DP alt-mode working on the USB-C port is on the 4.4 kernel which isn't supported by newer versions. Is there any backup repo for buster? Thanks

• 1

  Reputation Points

• 7 replies
• 4.2k views

lululombard

March 30, 20242 yr

Hi friends, I have one nagging thorn in my side that I just cannot figure out. I need someone who has a 1password account for help with this one. The problem - their desktop app and browser plugin work in tandem -- and it will not synchronize on Armbian for some reason. I've tried everything I can think of - ensuring nothing is downloaded from Flatpak and therefore sandboxed and preventing any connectivity issues. But still not working. If someone can take 5 mins and create a free trial account on 1password, then here are the steps to reproduce: Download the latest arm64 version of 1password Desktop: curl -sSO https://downloads.…

• 0

  Reputation Points

• 1 reply
• 2.7k views
• 1 follower

laibsch

July 26, 20251 yr

hey all, I have been running three Rock 5B+ for some time now with Proxmox arm port, and last night I did a kernel update to the latest, and now all three SBC are running extremely slow, PVE does not load, and there are a bunch of system errors (see below). I tried going back to an older kernel, but the same errors remain. any thoughts? Aug 18 07:13:00 PMOX2 kernel: rk806 spi2.0: no dvs-setting pinctrl state Aug 18 07:13:00 PMOX2 kernel: cpu cpu0: Failed to get specification_serial_number Aug 18 07:13:00 PMOX2 kernel: cpu cpu0: Failed to get specification_serial_number Aug 18 07:13:00 PMOX2 kernel: cpu cpu0: Failed to ge…

• 0

  Reputation Points

• 2 replies
• 2.9k views

bhouseski

August 18, 20251 yr

i have upgraded armbian on tinkerboard asus form 5.35 to 5.38. And this changed cpu governor to conservative. I have changed it to performance. BUT previous max cpu speed was 1.80GHZ and now i have only 1.61.GHZ I have cooler with fan on my tinkerboard and iam not scared high cpu temperature. Hov to get back to the maximum 1.80 GHZ frequency ???? I cant add 180000MHZ via sudo nano /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies to each core permission denied. please help

• 1

  Reputation Points

• 22 replies
• 15.6k views

constantius

April 15, 20188 yr

Hello, finally I have time to play with my OPI5, first thing I tried is to install on USB-C, but the port doesn't seem to work. Then I tried to install using USB3 port, on a ssd drive. The armbian-install utility seems to do the job and after installing the bootloader on mtdblock0 I powered off. At reboot everything is like before: if I remove the sd card the systen won't boot. If I boot with the sd card inserted the root partition is on /dev/mmcblk0p2 First thing that came into my mind is to mount SPI and check if bootloader is ok, but I'm unable to mount it: ~# mount /dev/mtdblock0 /mnt/spi mount: /mnt/spi: wrong fs type, bad optio…

• 0

  Reputation Points

• 0 replies
• 2k views

pazzoide

February 3, 20233 yr

Since I re-installed 23.8 Jammy with the extra ppa:liujianfeng1994 repo - I haven't been able to play any videos on my OPI5. All players I tried seem to have kernel issues decoding any h264. I've narrowed down the error message to a 4Gb memory limit with the selected version of the drivers but I was wondering if anyone had luck with playback. I had better luck with Jammy 23.4 and I regret upgrading. What is the recommendation? Should I try nightly with 6.6.0-rc1 kernel? I assume this one doesn't need panfork drivers anymore or are there other recommendations for h264 playback?

• 1

  Reputation Points

• 9 replies
• 4.5k views
• 1 follower

OttawaHacker

October 12, 20233 yr

Hmm, seems i need someone holding my hand all steps of the way 😇. Soon i'll need to pay some.. 🥰 I got my OPI5plus working from emmc with nvme-to-sata adapter on edge kernel and now i have 5 HDDs and 1 SSD connected to it. Intended for ZFS with cache... But : ZFS module won't build. I installed linux-headers and tried # apt install zfsutils-linux zfs-dkms. --- Setting up zfs-dkms (2.1.9-2ubuntu1) ... Loading new zfs-2.1.9 DKMS files... Building for 6.7.0-rc1-edge-rockchip-rk3588 Building initial module for 6.7.0-rc1-edge-rockchip-rk3588 configure: error: *** None of the expected "bops->release()" interfaces were detected. …

• 1

  Reputation Points

• 7 replies
• 6.2k views

QuaxEros

February 4, 20242 yr

Kind people： How to modify the default swap partition size in the configuration file and compile the firmware？？ help help

• 0

  Reputation Points

• 2 replies
• 2.9k views

lay

May 22, 20251 yr

Looks like only one HDMI port and one NVMe drive bays work on the edge kernels. Not sure whats wrong with HDMI port but two SSDs installed cause issues PCIE addressing. Probably overlay issue with the newer kernel images?

• 0

  Reputation Points

• 2 replies
• 1.5k views
• 1 follower

armbuilder

March 23Mar 23

There is no Orange Pi 5 results yet, but we can see already results of RK3588S. https://github.com/ThomasKaiser/sbc-bench/blob/master/results/Sorted-Results.md

• 0

  Reputation Points

• 0 replies
• 2.3k views
• 1 follower

MarcAndro

February 3, 20233 yr

Good day, I have Opi 5 and bought this display https://www.aliexpress.com/item/1005005641383181.html?src=google&aff_fcid=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&aff_fsk=UneMJZVf&aff_platform=aaf&sk=UneMJZVf&aff_trace_key=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&terminal_id=b834b596955b44a1bf643629f5ba5647&afSmartRedirect=y . It was a blind buy ... And now I can't get it work if its even possible. I'm its my first time trying to get display on these boards usually use them trought Monitor or TV and it works flawlessly. Cant find even config.txt . But now im lost at how to get …

• 0

  Reputation Points

• 2 replies
• 2.3k views

ower

January 21, 20242 yr

https://paste.armbian.com/qocicuyote.yaml <-- captured from debug UART Brand new odroid-m1, Samsung Pro Endurance 256GB; and a brand-new/uninitialized Samsung PM9A1 256GB NVMe. It drops me to a shell [presumably the initramfs]. Note: I'm not out of options yet, I can try building my own image with newer current or edge kernels. Edited to add: I think it's booting me to the petitboot env, not even attempting to boot the SD card,

• 0

  Reputation Points

• 1 reply
• 1.7k views
• 1 follower

tabrisnet

November 8, 2025Nov 8

Hello, I tired to boot Armbian for my Rock5b but whatever image I choose to use, I'm never able to get past U-boot into linux when looking at the Uart output. Here are the log I get: ``` U-Boot SPL board init U-Boot SPL 2017.09-gd1cf49135ee-220414-dirty #stephen (May 23 2024 - 19:39:28) Trying to boot from MMC2 GUID Partition Table Entry Array CRC is wrong: 0x71678773 != 0xab54d286 part_get_info_efi: *** ERROR: Invalid GPT *** part_get_info_efi: *** Using Backup GPT *** spl: partition error Trying fit image at 0x4000 sector ## Verified-boot: 0 ## Checking atf-1 0x00040000 ... sha256(7612223b82...) + OK ## Checking uboot 0x00200000 ..…

• 0

  Reputation Points

• 29 replies
• 6.1k views
• 1 follower

ScottP

August 19Aug 19

Hi there, I pourchased OPi5 (not preferred OPi5 Pro, because of Armbian lacking support), flashed Debian 24.8.1_bookworm_6.10.6_cinnamon_backported_mesa_desktop, configured (user, switch to static IP, user). Worked OK. Now, ssh'ing into showed "113 packages upgrade". Did "apt upgrade". Download OK, but when applying apgrade process hung twice: - once on "configuring libc", had to power off, then restarted (after an apt-get suggested in response to apt upgrade). Upgrade hung second time (no progress on bottom bar for hours, no new ssh session). - twice was on "configuring udev". After this, board is almost dead: - boots to anima…

• 0

  Reputation Points

• 11 replies
• 4k views
• 1 follower

laurentppol

November 27, 20241 yr

Hello comunity/maintainers, Please could anyone help me? After fesh install Debian 13 trixie Minimal (CLI) — current 6.18.44 there is no wlan0 nor hci0, only theese events in dmesg: [ 4.389072] Btrfs loaded, zoned=yes, fsverity=yes [ 4.987196] systemd[1]: systemd 257.13-1~deb13u1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +IPE +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 +PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +BTF -XKBCOMMON -UTMP +SYSVINIT +LIBARCHIVE) [ 5.729379] sysfs: cannot cre…

• 0

  Reputation Points

• 4 replies
• 1.1k views

slmq

September 13Sep 13

Hi All I'm trying to use a microphone using the audiojack connector but without any success. Any help around that? I tried to search in the forum but didn't find any useful information regarding Radxa 5B Plus Thanks Erez

• 0

  Reputation Points

• 3 replies
• 3.8k views
• 1 follower

Igor

April 15, 20251 yr

I updated to Armbian 26.2.1 on OPi5, and it can't boot from MTD (rootfs at NVMe), and I have to use SD card to boot to NVMe as workaround. After looking into this issue, I found rkspi_loader.img is no longer available for current (6.18.8 kernel) u-boot pkg and armbian-config flashes u-boot-rockchip-spi.bin ( or similar sata version) to /dev/mtdblock0 and I think this is wrong image for MTD bootloader. If I use older vendor image, which u-boot pkg has rkspi_loader.img, system can boot to NVMe rootfs and I notice that /dev/mtdblock0 has several gpt partitions including u-boot one, and flashing u-boot-rockchip-spi.bin erases partitions in SPI flash. I…

• 1

  Reputation Points

• 27 replies
• 10.5k views
• 2 followers

eselarm

April 28Apr 28

$ grep -i error /var/log/armbian-hardware-monitor.log [ 2.990779] rockchip-pcie f8000000.pcie: probe with driver rockchip-pcie failed with error -110 Looking at this I see the following: https://patchwork.ozlabs.org/project/linux-pci/patch/20210421083115.30213-1-jinsiyu940203@163.com/ "In function rockchip_pcie_host_init_port(), it defines a timeout value of 500ms to wait for pcie training. However, it is not enough for samsung PM953 SSD drive and realtek RTL8111F network adapter, which leads to the following errors: [ 0.879663] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout! [ 0.880284] rockchip-pcie f8000000.pci…

• 0

  Reputation Points

• 0 replies
• 1.2k views
• 1 follower

joejoe44

May 3May 3

I am after compiling a module for a wireless card. I got plenty of errors, thus decided to go to the basis and test the creation of a "hello" module. I am using the image: Armbian_22.11.4_Orangepi5_jammy_legacy_5.10.110_xfce_desktop.img vi hello.c ------------------------------------------------- #include <linux/init.h> #include <linux/module.h> static int hello_init(void) { printk("Hello Orange Pi -- init\n"); return 0; } static void hello_exit(void) { printk("Hello Orange Pi -- exit\n"); return; } module_init(hello_init); module_exit(hello_exit); MODULE_LICENSE("GPL"); ------------------------------…

• 1

  Reputation Points

• 8 replies
• 5.9k views
• 1 follower

gounthar

May 30, 20233 yr

Hi to all, In the past it was proposed by @Igor to use the u-boot-sunxi/remove-boot-messages-from-hdmi.patch this now as I can see under the allwinner-optional and seems do nothing on RockPro64 u-boot compile to hide the text @jock provided in the Tinker forum a userpatch disable-vidconsole.patch which works great on it (tinker) diff --git a/include/configs/tinker_rk3288.h b/include/configs/tinker_rk3288.h index bde7d72e6d..3ae9bb05f7 100644 --- a/include/configs/tinker_rk3288.h +++ b/include/configs/tinker_rk3288.h @@ -7,9 +7,9 @@ #define __CONFIG_H #define ROCKCHIP_DEVICE_SETTINGS \ - "stdin=serial,usbkbd\0" \ - "stdout=ser…

• 0

  Reputation Points

• 0 replies
• 2.2k views

2play

August 21, 20233 yr

I haven't tried Jammy with 6.1.43 but the kernel doesn't say rc anymore so curious of the status. How does this build compare in terms of feature and performance with 5.10? Is all the video decoding supported? The RK3588 Kernel support page says that hdmi audio is not supported - is that really the case? Is gnome/wayland supported? I see that only KDE is listed there.

• 0

  Reputation Points

• 1 reply
• 3.2k views
• 1 follower

Werner

April 12, 20242 yr

Hi ! I have a FriendlyElec NanoPi M5 and I want to play movies with it. But I want to squeeze everything out of this SBC ! So, I need hardware acceleration. I tested first with a OS image downloaded from FriendlyElec and mpv and (almost) everything works well. The mpv working configuration is: hwdec=rkmpp, vo=gpu, gpu-api=opengl. But I don't like that OS for other reasons, so I switched to Armbian. I installed the image "Armbian 26.5.1 KDE Wayland (Ubuntu 26.04 - vendor 6.1.115)", then I installed mpv, but when I try to play movies, it says: marus@nanopi-m5:/mnt/NAS/WDRed1/Samples/FullHD$ mpv --hwdec=rkmpp --vo=gpu --gpu-api=opengl H265.8bit.FullHD.192…

• 1

  Reputation Points

• 7 replies
• 2.3k views
• 1 follower

eselarm

July 8Jul 8

There's a way to change the framebuffer display resolution / refreshrate? Via HDMI my display work at 1920x1080 at 25Hz, i need to set it to 60Hz

• 0

  Reputation Points

• 0 replies
• 2.6k views

gleam2003

February 13, 20188 yr

Hi there! o/ I have noticed something... Odd. This is not a show stopper here, but the TinkerBoard NIC leds stays off all the time (if no traffic) even with link. It does blink somewhat schizophrenically when there's traffic. The right NIC led is bi-color and sometimes blinks in yellow, sometimes blinks in green. For what is worth, running Kernel 4.4-120. Issue also happened in build -104, which was the original Armbian image that I have downloaded. I thought it was something with the port, cables but... Traffic flows just normally Is it... normal? :-) Have a great (tinkering) weekend!!!

• 0

  Reputation Points

• 2 replies
• 2.5k views
• 1 follower

Rfreire

April 15, 20188 yr

Can anyone provide a link to a currently available and confirmed working USB to 3.3V TTL converter that works at 1500000 bps? The PL2303 I have technically supports up to 3 Mbps but only in certain discrete steps, and 1500000 is not one of those steps. The MCP2221A only supports up to 460800 bps. The FTDI FT232 data sheet claims support up to 3 Mbps but is unclear about whether arbitrary baud rates are supported, or only discrete steps like the PL2303. Searching for a compatible USB-TTL cable to work with the RK3399 has been futile so far. A link to a confirmed working cable would be much appreciated. Confirmed working cables only. No theoretical devices, please.

• 1

  Reputation Points

• 4 replies
• 8.4k views
• 1 follower

dpoon

January 25, 20215 yr

Hi, I have installed "Armbian_22.08.7_Tinkerboard_bullseye_current_5.15.74_minimal.img.xz" on a Tinkerboard (no S, with RK3288). I have tried to set the output of some header pins without success. I used both "sysfs" and "gpiod" (which uses char-devices). Test procedure, e.g. for pin 36 (gpio223): # echo "223" > /sys/class/gpio/export # cat /sys/class/gpio/gpio223/direction in # cat /sys/class/gpio/gpio223/value 0 # echo "out" > /sys/class/gpio/gpio223/direction # cat /sys/class/gpio/gpio223/direction out # echo "1" > /sys/class/gpio/gpio223/value # cat /sys/class/gpio/gpio223/value 0 # echo "0" > /sys/class/gpio/gpio223/value # ca…

• 0

  Reputation Points

• 4 replies
• 4.3k views
• 1 follower

usual user

November 26, 20223 yr

Orange Pi 5 is a new board using RK3588S. I think it would be really nice to support it http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5.html

• 1

  Reputation Points

• 141 replies
• 113.8k views
• 8 followers

balbes150

April 22, 20233 yr

hai, im planning to upgrade my local media server to use an external hard drive attached using hard drive docking on USB 3.0 what I'm confused about is. what is the best FileSystem format for my hard drive? I'm not planning to unmount and use the hard drive to another PC (for example: windows PC) So I'm ready to format it with FileSystem that fully optimizes on Linux (I'm using armbian noble) so ext4 or xfs? I hear xfs is better for copying large file sizes. my casual use is downloading movies, and watching it on jellyfin. or maybe I'm just using ext4?

• 0

  Reputation Points

• 1 reply
• 3.2k views
• 1 follower

Marco Schirrmeister

August 6, 20242 yr

May I ask where to add and place the background image？？ help.....

• 0

  Reputation Points

• 6 replies
• 3.7k views

Werner

September 5, 20242 yr

I am trying to install Ambian on to the BananaPi-M7 to eMMC using option 6. there is no option for NVME / M2 SSD. I had a failed install as the uSDCard image was 256GB larger than the eMMC, so it balked. I tried a 128GB uSDCard, followed by a 64GB uSDCard, but got the same error each time even on the 64GB one. I seem to have two partitions on the eMMC, mmcblk0boot0, and mmcblk0boot2 now,. I am not sure if they were on the boards eMMC originally or what the boot sequence for the board is If the Masked ROM tries to boot the uSDCard if present and if that fails it boots the eMMC ? Do I clear mmcblk0 and try again with the 64GB uSDcard ? Or is mm…

• 1

  Reputation Points

• 55 replies
• 25.5k views
• 1 follower

AaronNGray

December 15, 20241 yr

I connected an OV13850 camera to camera port 3. After enabling it in device tree config, I still can't see it in v4l2-ctl and other camera apps. dmesg | grep ov13850 shows nothing.

• 0

  Reputation Points

• 7 replies
• 4.2k views

unDefFtr

February 26, 20251 yr

Hi all, I have Armbian 22.08.6 Jammy with Linux 5.15.74-rockchip with Desktop running on an "Asus Tinker Board Rev. 1.2". My Problem is that I get no stable HDMI Connection. Picture is appearing and disappearing every few seconds. Changing Cable, Monitors, Resolution and Refreshrate doesn’t change the problem. After Research in the forum I saw that I should provide „armbianmonitor -u“ here: https://paste.armbian.com/oriqiwilah I would be able to compile a custom image, but I don‘t know where to start bugfixing because I am no HDMI Expert. Maybe it has something to do with a Sync-Problem like described …

• 0

  Reputation Points

• 2 replies
• 3k views
• 1 follower

Onelight

October 25, 20223 yr

Hello, I installed lm-sensors on my Opi5 and I'm able to check temperatures, however I don't know how to make the little fan spin when the temperature rise. I know the temperature is not going to rise till critical levels, but I live in very hot country and I just don't want my device to become too hot. And do you know how to make the fan start at certain temperature rise? Also I'm not sure which pins I should connect the fan to.. One pin should be the 3.3V to get the power, what about the other one? I'm running Armbian 23.02.2 with kernel 5.10.110-rockchip-rk3588 Thanks in advance

• 1

  Reputation Points

• 48 replies
• 58.2k views
• 8 followers

JohnU

January 13Jan 13

Hello Developers, I ran into some issues installing the latest release on an Orange Pi 5 Plus. The images I downloaded are as follows: Armbian_24.11.2_Orangepi5-plus_noble_current_6.12.0_kde-neon-kisak_desktop.img.xz Armbian_24.11.2_Orangepi5-plus_noble_vendor_6.1.75_gnome-kisak_desktop.img.xz The KDE version will install and boot from the 256GB emmc drive, however it only works if there is a 4K HDMI monitor attached to HDMI1, I was not able to get it to display on a 1920x1200 HDMI monitor nor a USB connected or HDMI connected portable display (2560x1440). The Gnome version will boot with any of those 4 types…

• 0

  Reputation Points

• 7 replies
• 8.6k views

Werner

January 10, 20251 yr

Anyone here playing with USB network adapters? I have a (noname) USB3 Gigabit ethernet adapter which seems capped at 250 Mbps. I know the Tinkerboard only has USB 2.0 (so a theoretical maximum of 480 Mbps), just trying to see if there are better parts out there I could try.

• 0

  Reputation Points

• 5 replies
• 6.2k views
• 1 follower

root

April 14, 20188 yr

Hi, I am trying to make the RPI camera ( OV7750 ) to work with the TInkerboard in Armbian. But there is no module in /lib/modules for this camera. Is it already compiled in the kernel? Currently it doesn't work.

• 0

  Reputation Points

• 1 reply
• 3.4k views
• 1 follower

chwe

November 15, 20187 yr

Hello, I have set kernel.panic=180 in /etc/sysctl.conf to reboot on a kernel panic. Before, the system would keep running/hanging and I could read the errors if I turned on a attached display. Now the result is that the tinkerboard switches off. My expected result would be a reboot. Do I have to set something else? Or do I need to use watchdog? I am using the original tinkerboard with debian bullseye, kernel 5.15.48-rockchip.

• 0

  Reputation Points

• 2 replies
• 3k views
• 2 followers

tinker

August 26, 20224 yr

Good evening, last week they changed the electric meter in my building, but in order to do so they cut the power, and my Tinkerboard (the first model, the one issued back in 2017, Asus first's SBC), that I use as my "Save for later, and never look at it again" network folder, suffered. It continued to reboot from some kernel panic, which I forgot to take note; but since it hadn't been upgraded to jammy, I took the opportunity to do it. Pluging in the uSD card (with the newly released jammy version, just downloaded here), power, and all (including the ethernet cord!!), first boot I have to create my user (which, for some reasons refuses to let me put my usual fr3d tag…

• 0

  Reputation Points

• 20 replies
• 17.4k views
• 2 followers

fr3d

April 14, 20242 yr

ubuntu22 gnome desktop Hi, may I ask how to install Google Chrome

• 0

  Reputation Points

• 1 reply
• 4.7k views

Igor

November 26, 20241 yr

As the title says, how can I install the ntsync kernel module for use with Wine/Proton?

• 1

  Reputation Points

• 4 replies
• 4.1k views

The Tall Man

September 10, 20251 yr

Hi all. Is heatsink required for the libre 3328? When I log in to armbiam temp says 60 but it is in red text.

• 0

  Reputation Points

• 4 replies
• 4.5k views

Johnny

November 21, 20187 yr

Hi, I am struggling to get the second NIC (1Gbit) to work. The wireless and first NIC (100Mbit) works All NIC's connected I am using Armbian 22.11.0-trunk Bullseye root@rockpi-e:~# ifconfig -a eth0: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 9a:9c:84:a1:77:63 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 41 eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.150.1…

• 0

  Reputation Points

• 5 replies
• 4.4k views
• 1 follower

maigonis

November 24, 20241 yr

I installed Armbian on my R4SE downloaded from https://redirect.armbian.com/nanopi-r4s/Bookworm_current_minimal Everything seems to work just fine, but I am missing my second network interface. Only the WAN interface is shown. Is there a software fix I can apply, or should it be fixed in the OS image? armbianmonitor -u output: https://paste.armbian.com/gipilapuve

• 0

  Reputation Points

• 2 replies
• 3.3k views
• 1 follower

Junkman

November 25, 20232 yr

I tried installing the OS using SD card and EMMC, but both failed. Orange Pi OS (Arch) on the official website ran normally. However, I installed focal_desktop_xfce or jammy_desktop_gnome from Ubuntu Image, but they all failed. After inserting the image into the SD card, the symptom is a black screen and no booting. Does it only support SSD? Because it is entered through a translator, there may be unnatural sentences. If you reply about that, I will get back to you.

• 1

  Reputation Points

• 20 replies
• 37.3k views
• 2 followers

deskwizard

September 5Sep 5

Built image with such flags: Etched img to sdcard and SBC has no response on power up. U-boot log: OS boots normally if I use ext4, but would like to stick to f2fs. Btrfs or f2fs used to work if I used 7 months old armbian-build git checkpoint but not any more. Anyone else had similar problems?

• 0

  Reputation Points

• 2 replies
• 1.4k views

temp739

April 11Apr 11

I hear something about a new version of the board Thinkerboard, "Tinkerboard S". I want to know what you know and think about it. https://www.asus.com/Single-Board-Computer/Tinker-Board-S/

• 1

  Reputation Points

• 13 replies
• 7.7k views

TonyMac32

February 16, 20188 yr

HI all, first of all, I found thi sissue adopting a new board to the CSC tree, done by @balbes150. As it seems to be a problem of RK3288 in general, I post here, in case please move the topic to the approriate place. I have a JLD076 board, and started adjusting the DTS to the schematic. According to the schematic, and the TRM of RK3289, there is a maximum number of 160 GPIOs. This is also the number I get from my schematics. So I expected th get suitable number of pins from gpioinfo (bank:number 0:19, 1:4, 2:18, 3:28, 4:26, 5:12, 6:19, 7:24, 8:10). Instead, I get listed (0:24, 1...7:32, 8:16). I tried now to set ngpios for the &…

• 0

  Reputation Points

• 0 replies
• 3.4k views

mboehmer

October 5, 20206 yr

Standard install - Armbian Bookworm, full 'firmware install'. I am getting some packet loss over the LAN. A raspberry pi, Synology NAS and Deban x86 install on the same LAN do not seem to exhibit the same loss. Anyone have experience or ideas? Oddly enough this never seems to occur on fresh installs. This is a docker host for pihole and home assistance, no other packages are really installed at all. I've not really tried much, but since this is a standard install, apt-get update & upgrade are about the only modifications outside of docker install that has occurred. 1. This plugs directly in to a Ubiquiti switch 2. I have tried a few differ…

• 0

  Reputation Points

• 3 replies
• 2.6k views

royk

September 21, 20233 yr

I have connected USB 3.0 4 port hub to the type c of my radxa zero 3E but lsusb -t shows the hub is only on USB 2.0 as 480M. /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M /: Bus 05.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M and lsusb output Bus 002 Device 0…

• 0

  Reputation Points

• 7 replies
• 6.7k views
• 1 follower

Ali Alaei

July 15, 20251 yr

Dear All, I am running a project with Tinkerboard and a gigE camera. Trying to take video image through gstreamer (gst-launch). The camera is an Imaging source camera (DFK 33GX249) and I am using the linux library (https://github.com/TheImagingSource/tiscamera) for developing apps. My Tinkerboard is running Armbian Stretch (Armbian_5.50_Tinkerboard_Debian_stretch_next_4.14.52_desktop) Everything is working perfectly untill I am trying to run the command below: tinker@tinkerboard:~$ TCAM_LOG=DEBUG gst-launch-1.0 --gst-debug=tcamsrc:5,tcambin:5 --gst-debug-no-color tcambin ! videoconvert ! autovideosink The output is: Spoiler …

• 0

  Reputation Points

• 2 replies
• 2.7k views
• 1 follower

Igor

May 8, 20197 yr

hi all, I am wondering if there's any reason that CEC is not built into legacy kernel for RK3399. In https://github.com/armbian/build/blob/master/config/kernel/linux-rk3399-legacy.config, module dw-hdmi-cec is not enabled. # CONFIG_DRM_DW_HDMI_CEC is not set If no special reason, I can make a PR for this. Thank you!

• 0

  Reputation Points

• 1 reply
• 4.1k views

Igor

December 13, 20205 yr

Hello I cannot enable the Bluetooth on Tinkerboard device. Tried latest image, fresh install. I've opened the question on StackOverflow: https://superuser.com/questions/1698728/cannot-enable-bluetooth-on-tinkerboard-armbian It contains technical details. The latest what I've found so far is it could be related to Kernel compilation flags: # Extract from the /boot/config-5.10.60-rockchip CONFIG_SERIAL_DEV_BUS=y CONFIG_BT_HCIUART_3WIRE=y CONFIG_BT_HCIUART_SERDEV=y # CONFIG_BT_HCIUART_RTL - is not set # CONFIG_SERIAL_DEV_CTRL_TTYPORT - is not set I tried to download and compile the kernel and stuck. Basically I do…

• 0

  Reputation Points

• 14 replies
• 6.3k views

ning

November 7, 20223 yr

I have created a micro desktop case. It's an open design that is still in the creation phase. The shell is 3d printed, the sides are acrylic, and the opi5 mount panel can be 3d printed or made from acrylic. I'm looking for feedback with design suggestions/needs. This is the first real opi5 micro tower design currently for OPI5. My cad drawing of the OPI5 mainboard is 99.9% accurate, so if someone wants to use that as a footprint for other projects by all means. https://github.com/berin-aquaquad/orange-pi-5 I am using DesignSpark Mechanical a free cad software that is on par with Fusion360. The shell has been designed as a split body so smaller 3d printers can c…

• 1

  Reputation Points

• 63 replies
• 30.8k views
• 3 followers

berin

November 8, 20241 yr

Hi all I hava an orange pi 5 plus with a 512GO NVME SSD. I have installed the latest version od Armbian to a SD card it work well, but for speed reason i would like to install the OS to th SSD drive and boot from this device and no longer from the SD card. Is there a way to do this ? i mean from u-boot point of view? i can keep a SD card inside it to store u boot but i would like to move usr var and such to SSD Thanks in advance for your answers comment or ideas W.

• 0

  Reputation Points

• 3 replies
• 4.9k views
• 1 follower

William Bonnet

June 13, 20242 yr

Hi there, I wanted to know if anyone know if there are any power limits from the SATA power ports, the question is can you power 1 or more 3.5" NAS disks at the same time? Or as a precaution, I take power from the PSU? Thanks, Dany

• 1

  Reputation Points

• 3 replies
• 3.5k views
• 2 followers

ozacas

November 19, 20241 yr

Hi all, Testing this OP5, got a standard M2 NVMe SSD (this works on my OP5Plus) I have formatted to exFAT with windows, inserted on the OP5, loaded ArmbianOS on MicroSD, it boots fine but I cant get it to show the nvme drive using fdisk -l or lsblk It seem like its not detecting the m2 nvme ssd at all.. little help please ?

• 0

  Reputation Points

• 12 replies
• 10.8k views
• 2 followers

zjd

May 9May 9

The OPI5 has an onboard RTC. On the back of the board near the RTC chip there are two pcb "test points". One says RTC1, the other says GRD1, I would assume a CR2032 could be connected to those points to maintain RTC function. I don't dare do anything till I get a solid answer. Can anyone give me any feedback as to options.

• 0

  Reputation Points

• 10 replies
• 10.5k views

ScottN

April 27, 20233 yr

I installed latest Armbian_24.5.1_Orangepi5-plus_bookworm_vendor_6.1.43_minimal.img and I can't get wifi to work. The adapter is RTL8852BE. I installed armbian-firmware-full and the adapter is shown in lspci, but there is no wireless interface. armbian-config does not list wifi as an option. armbianmonitor -u

• 0

  Reputation Points

• 6 replies
• 10.8k views
• 4 followers

EricaLina

January 1, 20251 yr

Today my effort is getting the rk3288 tv box boot from USB devices. During the initialization of the OTG USB port, u-boot complaints about dwc_otg_core_host_init() function which is timing out. I tried to manipulate the device tree chaning the dr_mode flag to host, otg and peripheral, but nothing changed. The only way to get rid of the timeout is to disable the device which, by the way, seems to not work anyway. U-Boot 2017.09 (Jun 17 2018 - 18:55:17 +0200) Model: XT-Q8L-V10-RK3288 DRAM: 2 GiB MMC: dwmmc@ff0c0000: 1, dwmmc@ff0f0000: 0 ** First descriptor is NOT a primary desc on 0:1 ** In: serial Out: serial Err: serial Model: XT-Q8L-V10-RK3288 …

• 0

  Reputation Points

• 2 replies
• 4.1k views
• 1 follower

jock

June 18, 20188 yr

Hi! On the Rockpro64, with the latest Amrbian dev kernel (5.4.0-rc1-rockchip64 updated on 19th of January), the sata hard drive connected to PCIe through the pine store adapter does not go to sleep anymore. It is properly set with hdparm and a udev rule, it used to work fine with the dev kernel before the 19th of January update. Now, if I issue a sleep commd (hdpram -y /dev/sda) it goes to sleep properly but not by itself after the 5 minutes inactivity I have set up. Mathias

• 1

  Reputation Points

• 5 replies
• 4.6k views
• 1 follower

Mathias

April 16, 20206 yr

After some days of uptime Zram usage is 100% https://paste.armbian.com/fecegemiwe What can I do with it?

• 0

  Reputation Points

• 6 replies
• 4.9k views
• 1 follower

atone

January 17, 20233 yr

System Information: https://paste.armbian.com/mozehisomu When i am trying to setup many vlan interfacces i have whis dmesg message: rk_gmac-dwmac fe1c0000.ethernet eth0: MAC_VLAN_Tag_Filter full (size: 4) interface info: ethtool -i eth0 driver: st_gmac version: Jan_2016 firmware-version: expansion-rom-version: bus-info: supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: yes supports-priv-flags: no I need about 20-30 vlan interfaces

• 0

  Reputation Points

• 16 replies
• 8.3k views
• 4 followers

DeVILRuNNeR

January 22, 20251 yr

Ubuntu Noble had some early day issues with default key ring not being stored properly and or synced to the logged in user and users getting popup prompts about the default keyring locked. A week ago I downloaded Armbian Noble 25.5.2 desktop onto my OPi5. It has been my daily driver for the past week or so. It has been a really nice release for my OPi5. All has been good except the default keyring popups. I have created new users, deleted stored keyrings, changed passwords among other things. At this point I am able to store the default keyring password (which is the same as my login PW). However, when launching chromium, and ProtonVP…

• 0

  Reputation Points

• 2 replies
• 2.4k views

SteeMan

July 24, 20242 yr

Does the khadas EDGE2 ARMBIAN system support Mali GPU by default?

• 0

  Reputation Points

• 2 replies
• 2.2k views

lay

August 28, 20242 yr

There's a strange issue with my orange pi 5 plus. When I boot into the ubuntu image, everything is fast, stable and zippy. But when I boot into the openmediavault image, it's incredibly slow. Simple operations like apt upgrade crawl. I noticed the cpu frequency is stuck at 408 MHz in htop in the openmediavault image. I ran a test. I opened another console and ran yes. Went back to htop and the frequency was still stuck at 408 MHz with one core pegged at 100% from the yes. So I fired up the ubuntu image and did the same thing. The core was at 100% but the frequency was at 2304mhz on that core. There is something wrong with the openmediavault …

• 0

  Reputation Points

• 1 reply
• 2.5k views

Mentaluproar

January 27, 20251 yr

Can anyone tell me if it's possible to install renegade firmware on a Rasperry Pi build for example? Libre used to host a script for a tool that achieved this but it hasn't been updated since Buster TIA

• 1

  Reputation Points

• 5 replies
• 2.3k views
• 1 follower

0jay

November 27, 2025Nov 27