Rockchip

Can you tell me how I'm able to enable PWM? I'm not able to see any of them in the armbian-config overlay management

• 0

  Reputation Points

• 1 reply
• 2.5k views

Werner

March 28, 20251 yr

The HDMI0(Port next to Headphone Jack) is driven by DP1 on rk3588 via RA620(a dp2hdmi converter). https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch/arm64/boot/dts/rockchip?h=v6.18&id=07c53a9e970712b1a479dd0ec4adfe184482c22f ROCKCHIP_DW_DP is needed in order to have working 2nd HDMI port. In menuconfig : Device Drivers ---> Direct Rendering Manager (XFree86 4.Graphics support ---> 1.0 and higher DRI support) ---> Rockchip specific extensions for Synopsys DW DP <pre> │ CONFIG_ROCKCHIP_DW_DP: …

• 0

  Reputation Points

• 2 replies
• 2.5k views

Popolon

December 13, 2025Dec 13

hello. I have a problem for quite some time on my tinkerboard. I do not know if it's a software or hardware problem. It appeared after connecting a special Raspberry USB Hub http://www.uugear.com/product/7-port-usb-hub-for-raspberry-pi/ I used this HUB on a raspberry 3b but he grilled the wifi chip (disappeared totally). I thought I had to grill the wifi chip of the tinkerbard like the raspberry but I can see the chip turn on from time to time. Today she has reappeared but "wlan0 not ready" in the network manager. sudo ip link show wlan0 wlan0: <BROADCAST, MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000…

• 0

  Reputation Points

• 0 replies
• 2.5k views

dragonlost

November 9, 20187 yr

I bought a wifi dongle (for 3 pounds on ebay!) having a realtek chip 8821cu. There were some disconnects from time to time, and I was unable to find out why from the logs. Few days ago I installed and recompiled the realtek drivers from https://github.com/lwfinger/rtw88, got some new modules, replaced the modules in the directory /lib/modules/6.1.43-vendor-rk35xx/kernel/drivers/net/wireless/realtek/rtw88 Since then, I have no more disconnect. This may helps someone maybe.

• 0

  Reputation Points

• 0 replies
• 2.5k views

Tony3

August 4, 20242 yr

Hello everyone, I’m using a Radxa Zero 3E with Armbian 24.8.1 Bookworm OS and trying to connect a device to Radxa via UART. However, I can’t seem to find the ttyAML0 interface. The only UART interfaces visible are ttyS1 and ttyFIQ0 , but neither works for my setup. I have connected the device to the UART_AO_A pins (pins 8 and 10). Additionally, when I go to armbian-config -> System -> Hardware, no hardware appears on the screen. Could this issue be related to the Armbian image I am using? I’ve already tried the b6 image, but it has a boot problem. I also noticed that the other official Radxa images are marked as pre-release. …

• 0

  Reputation Points

• 1 reply
• 2.5k views
• 1 follower

Werner

September 19, 20242 yr

I have a RK3588 (Radxa Rock 5C) system running Armbian Debian Trixie. I have the heatsink and the fan installed as well. I set the fan PWM to 255 as soon as temperature reaches 50 degrees via a systemd service. When using all 8 cores, the system overheats (>110 degrees) and eventually shuts down. For example, when compiling ffmpeg, it works fine with 'make -j6', but 'make -j8' results in a shutdown before compilation is complete. Likewise I had thermal issues when using llama.cpp. Shouldn't the OS throttle the CPU when temperature reaches high levels? I think that is not happening at the moment. Online search referred me to cpufrequtils to …

• 0

  Reputation Points

• 4 replies
• 2.5k views
• 1 follower

ileri

March 9Mar 9

There's a strange issue with my orange pi 5 plus. When I boot into the ubuntu image, everything is fast, stable and zippy. But when I boot into the openmediavault image, it's incredibly slow. Simple operations like apt upgrade crawl. I noticed the cpu frequency is stuck at 408 MHz in htop in the openmediavault image. I ran a test. I opened another console and ran yes. Went back to htop and the frequency was still stuck at 408 MHz with one core pegged at 100% from the yes. So I fired up the ubuntu image and did the same thing. The core was at 100% but the frequency was at 2304mhz on that core. There is something wrong with the openmediavault …

• 0

  Reputation Points

• 1 reply
• 2.5k views

Mentaluproar

January 27, 20251 yr

I downloaded the kernel source and kernel headers on a rk3288 rockchip (tinkerboardS) and noticed there was a mismatch between kernel version, armbian release and chipset (rockchip64) - see below. root@tinkerboard:~# uname -a Linux tinkerboard 4.4.174-rockchip #7 SMP Sun Feb 10 11:57:26 CET 2019 armv7l armv7l armv7l GNU/Linux root@tinkerboard:~# cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=tinkerboard BOARD_NAME="Tinkerboard" BOARDFAMILY=rockchip VERSION=5.75 LINUXFAMILY=rockchip BRANCH=default ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage root@tinkerboard:/usr/src# …

• 0

  Reputation Points

• 0 replies
• 2.4k views

Roland G

May 19, 20197 yr

Hello, Recently I have upgraded Armbian on my PBP (w/o kernel). My current kernel is 5.10.60 #21.08.1. I know, it's old but the newer only makes PBP unusable at all - black screen on boot. My current issue concerns the PBP keyboard. Some keys started generating weird outputs. I have never faced with something like that. When I press 'q' - output is - aq2468 x - zxetuj c - cfghk d - DWRI 1 - the screen is dimming I have no idea if this is software or hardware issue. The computer was on the shelf. Nothing has happened to it physically. After years of fighting with this crap :( - I want to be sure if that is the last straw to put this com…

• 0

  Reputation Points

• 0 replies
• 2.4k views

bushw

November 15, 20241 yr

pi@opi5:~/AoC-2023-cplusplus$ lscpu --all --extended CPU SOCKET CORE L1d:L1i:L2:L3 ONLINE MAXMHZ MINMHZ MHZ 0 0 0 0:0:0:0 yes 1800.0000 408.0000 1800.0000 1 0 1 1:1:1:0 yes 1800.0000 408.0000 1800.0000 2 0 2 2:2:2:0 yes 1800.0000 408.0000 1800.0000 3 0 3 3:3:3:0 yes 1800.0000 408.0000 1800.0000 4 0 0 4:4:4:0 yes 2256.0000 408.0000 2256.0000 5 0 1 5:5:5:0 yes 2256.0000 408.0000 2256.0000 6 1 2 6:6:6:0 yes 2304.0000 408.0000 2304.0000 7 1 3 7:7:7:0 yes 2304.0000 408.0000 2304.0000 Why the odd cortex a76 MAXMHZ …

• 0

  Reputation Points

• 4 replies
• 2.4k views

lurk101

January 8, 20242 yr

root@orangepi5:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 223.6G 0 disk ├─sda1 8:1 0 256M 0 part /boot └─sda2 8:2 0 221.1G 0 part /var/log.hdd / mtdblock0 31:0 0 16M 0 disk mmcblk1 179:0 0 29.8G 0 disk ├─mmcblk1p1 179:1 0 256M 0 part └─mmcblk1p2 179:2 0 29.2G 0 part zram0 254:0 0 7.7G 0 disk [SWAP] zram1 254:1 0 50M 0 disk /var/log root@orangepi5:~# cat /boot/armbianEnv.txt verbosity=1 bootlogo=false overlay_prefix=rockchip-rk3588 overlays=orangepi-5-sata fdtfile=rockchip/rk3588s-orangepi-5.dtb r…

• 0

  Reputation Points

• 4 replies
• 2.4k views

Werner

June 7, 20233 yr

!!! Warning !!!: Think twice before you upgrade kernel on your PineBook Pro. After years unfortunately I decided to unlock upgrades Armbian Kernels and upgraded kernel to the newest one (current) - 5.15.93. After reboot Armbian couldn't find my encrypted root disk and booting ended every time in (initramfs). I installed again kernel 5.10.60 #21.08.1 and Armbian finds my encrypted disk again. Of course still there is no information that I have to enter the password to unlock disk but only black screen. Happily I know that I have to enter the password when the screen is black. Every upgrade of Armbian is connected with a dose of stress that I'll have to …

• 0

  Reputation Points

• 1 reply
• 2.4k views

Igor

January 16, 20242 yr

I have an Radxa 5B+ that are powered through POE HAT. The problem is that POE HAT fan does not work at all. I have to identical machines, same issue on both of them. I have installed Armbian minimal Bookworm on both, on nvme ssd.

• 0

  Reputation Points

• 2 replies
• 2.4k views

Werner

December 15, 2025Dec 15

Good afternoon. I bought a NanoPi R76s rev. 2 (3GB RAM + 0 EMMC). It works fine with the manufacturer's firmware. However, it doesn't boot on Armbian (26.02.1). I assume rev. 2 isn't supported. Is it possible to add support? Armbian_26.2.1_Nanopi-r76s_noble_vendor_6.1.115_gnome_desktop.img.xz Скрытый текст --- my build from tag 26.02.1: (log https://paste.armbian.com/poduzitifu ) Скрытый текст --- vendor ubuntu boot log https://drive.google.com/file/d/1OZqZk48LsbSzFz63fcqMKVp5YkhyNOoT/view?usp=drive_link (rk3576-sd-ubuntu-noble-gnome-desktop-6.1-arm64-20260403.img.gz) Скры…

• 0

  Reputation Points

• 10 replies
• 2.4k views
• 1 follower

SuperKali

May 28May 28

Hi, I am currently using rock-5-itx to setup a NAS. Everything is working fine. uname -a: Linux amberbyte 6.1.75-vendor-rk35xx #1 SMP Thu Nov 28 03:16:11 UTC 2024 aarch64 GNU/Linux Now, I wanted to update RKNPU version from 0.9.7 to 0.9.8. So, again I recompiled the image with the updated drivers. Using Pi-imager flashed it onto an SD card. When I tried to boot I am getting the following error message from the serial output: ./compile.sh build BOARD=rock-5-itx BRANCH=vendor BUILD_DESKTOP=no BUILD_MINIMAL=yes EXPERT=yes KERNEL_CONFIGURE=yes RELEASE=bookworm DDR 9fffbe1e78 cym 24/02/04-10:09:20,fwver: v1.16 LPDDR5, 2400MHz channel[0] BW…

• 0

  Reputation Points

• 1 reply
• 2.4k views

Werner

May 20, 20251 yr

Hello, I noticed that the system has created a swap partition by default. So, Where does the system default to creating swap exchange partitions??

• 0

  Reputation Points

• 3 replies
• 2.4k views

lay

November 22, 20241 yr

Can't seem to get bluetooth working with trixie and pipewire. I can pair & trust, just can't connect. Failed to connect: org.bluez.Error.Failed br-connection-profile-unavailable Anyone else had this issue? Was working fine on a cubie running bullseye, so next maybe I'll try and older os and see...

• 0

  Reputation Points

• 3 replies
• 2.4k views
• 1 follower

Meestor_X

February 17Feb 17

Hello, I have several Hardware working with the Tinkerboard / S and like to propose those to the "Tested 3rd party hardware" section To whom can i address this? Thanks Roman

• 0

  Reputation Points

• 0 replies
• 2.4k views

SecureXperts

March 16, 20197 yr

The Gnome desktop Power off menu selection and `sudo shutdown now` both reboot rather than powering down.

• 0

  Reputation Points

• 2 replies
• 2.4k views
• 1 follower

AaronNGray

July 21, 20251 yr

Here in the forum the psu mod for the roc-rk3328-cc board was discussed. Does anyone know where I can find instructions on how to do this exactly?

• 0

  Reputation Points

• 0 replies
• 2.4k views

ska

March 28, 20233 yr

At first, the card was recognized as a Mass Storage, I used usb_modeswitch to make it recognized as a wifi card, but iwconfig still didn't show this card, and /sys/kernel/debug/ieee80211 did exist, but was empty. I don't think it's a driver issue because when I plugged this card into my debian laptop, it worked even without usb_modeswitch. journalctl and lsusb logs are in the files. journalctl.log lsusb.log

• 0

  Reputation Points

• 0 replies
• 2.4k views
• 1 follower

MCredbear

February 22, 20233 yr

Dear Colleagues! In the I2S RK3288 interface rather limited number of timeslots of TDM (PCM). I try to use RK3288 spi as the subordinate controller for input and processing of a data stream of TDM (128 timeslots). Was - whether you have a practice of creation of spi of the driver for operation in slave DMA?. Perhaps for other chip. I will be glad to responses! Thanks!

• 0

  Reputation Points

• 0 replies
• 2.4k views
• 1 follower

sultan

July 27, 20188 yr

Hi there, I've been using ARMbian for a couple of years now under a Rock Pi S board. I'm using an ARMbian OS image based on kernel 4.4x because it have a virtual wlan interface called P2P0, this allow me to use the board as WiFi repeater, I've written a post about it here. However, in recent ARMbian OS images with kernel 5.x and 6.x that virtual interface isn't there. I see in ARMbian OS image with kernel 6.x that the WiFi Hotspot set up menu in the armbian-config tool show an interface called p2p0-dev, but it doesn't work. My question: why? these newer kernels have limitations on this board? or maybe need to compile the kernel with custom modifications?. …

• 0

  Reputation Points

• 0 replies
• 2.4k views
• 1 follower

AlexanderG

July 10, 20233 yr

Trying the Armbian Radxa Rock5T 25.5.1 / 6.1.115 Ubuntu server image for the Rock5T and I can't get the Quectel M2 EM12-G WWAN card to be recognized at all. I was previously running the Joshua Reik image and the card showed in lsusb on that image and worked, but I can't figure out why it's not working on this image. I'm kind of new to all this. I did find this similar thread but never found a resolution. https://forum.radxa.com/t/rock-5b-wwan-support-hardware-bug/25780 Hopefully someone can help as to what could be going on. Edit: Armbian Monitor Here: https://paste.armbian.com/avusulewax

• 1

  Reputation Points

• 5 replies
• 2.4k views
• 1 follower

swthpk32

August 9, 20251 yr

I would like to setup NTPD with PPS but seems GPIO PPS is not yet supported. Anyone working on this?

• 0

  Reputation Points

• 0 replies
• 2.4k views

Fred Munden

September 5, 20179 yr

Starting a new thread after this one solved my question: https://forum.armbian.com/topic/15044-how-to-re-format-and-remount-and-redo-lvm-volume-on-ssd/?tab=comments#comment-107672 but taking care of those things wasn't the root cause. it turns out the drive wasn't unmounted cleanly after accidentally unplugging the power cable from the board. I had a drive setup using: pvcreate /dev/nvme0n1 vgcreate rockpro64 /dev/nvme0n1 lvcreate -n <name> -L 500g rockpro64 then i formatted like this: mkfs.ext4 /dev/rockpro64/name but then i accidentally unplugged the power source while i got my system up and running it wasn't cleanly unmounte…

• 0

  Reputation Points

• 0 replies
• 2.4k views

kkdao

September 1, 20206 yr

Running Armbian 23.8.1 Jammy CLI Minimal. Since my kernel updated to 6.1 I have been having serious stability issues. Uptime is somewhere between 3 and 24 hours before the system becomes completely unresponsive. Prior to the 6.1 update this system was rock solid and would be up for months at a time, only ever rebooted for kernel updates. I currently have a monitor plugged in running dmesg -W hoping for something when these hard locks are occurring but I am not seeing anything to indicate what the issue may be. armbianmonitor-u output is: https://pastebin.com/DeU8VsB4 Any suggestions on any additional debugging I can enable to tr…

• 0

  Reputation Points

• 0 replies
• 2.4k views

Varimir

October 10, 20233 yr

I am trying to compile a new kernel in order to support some satellite receiver tuner (from TBS). I did that successfully (In February 2023) on Orange Pi 5 with Linux kernel 5.10.110, but I am struggling doing it with Orange PI 5 Plus with Linux 5.10.160 (jammy). Basically I would like to turn as Modules lots of CONFIG_VIDEOBUF2_*, in order to replace the modules with the ones compiled separately (that I know are working fine with my TBS USD card). These are my issues: - I do not manage to set separately those CONFIG_VIDEOBUF2_* through the menu config. - Thus I tried to set the whole "multimedia support" as a module and go…

• 0

  Reputation Points

• 3 replies
• 2.4k views

Tony3

September 17, 20233 yr

I'm booting it from Armbian_24.11.1_Rock-5c_bookworm_vendor_6.1.75_minimal.img.xz image from a SD card. When launching `armbian-install`, there's only one option: (5) - Install to SD card I would like to install the bootloader to the SPI flash module but the option is not present. Furthermore it seems that my SPI module isn't detected either when running ls /dev/mtd* -> no mtdblock I decided to move on and I flashed https://dl.radxa.com/rock5/5c/images/loader/spi/rock-5c-spi-image-20240528.img to my 5C lite SPI flash module. However, there's no display and both LEDs are lighted up (green and blue) without blinki…

• 0

  Reputation Points

• 0 replies
• 2.4k views

peltho

January 10, 20251 yr

Armbian 21.08.1 Bullseye with Linux 5.10.60-rockchip64 power supply OK, sdcard OK, installed OMV. For this reason ,https://forum.armbian.com/topic/20237-renegade-aka-roc-rk3328-cc-usb30-not-work-properly/ , I 'freeze' armbian kernal upgrades to make USB-disk work properly. But, Either poweroff in CLI or in OMV panal, it always reboot.

• 0

  Reputation Points

• 0 replies
• 2.4k views
• 1 follower

PP88PP

April 12, 20224 yr

Sorry bad English. I advise that I'm a noob. I have a MKS TS35 v2.0, that uses ST7796/ILI9341 (or ILI9486, I think) for LCD and ADS7843E for touch, and now I want to use it in my Asus Tinker Board for Klipper. I know that it's possible because exists one HOW-TO of this for Raspberry Pi 3b+. I wanna that someone, with knowledge in Armbian and Tinker Board, build (adapt) this DTS on GITHUB https://github.com/fbeltrao-br/mksts35/blob/main/mksts35v2.dts. I want this especially because the pinout https://github.com/fbeltrao-br/mksts35/blob/main/pinout.png, that is more easy for me understand what pins I need connect.

• 0

  Reputation Points

• 0 replies
• 2.4k views

danihmorais

February 7, 20251 yr

Why so few Debian (Trixie) images with this batch of newly released images? Not one full desktop image for Debian?

• 0

  Reputation Points

• 1 reply
• 2.4k views

Igor

December 4, 2025Dec 4

Ubuntu Noble had some early day issues with default key ring not being stored properly and or synced to the logged in user and users getting popup prompts about the default keyring locked. A week ago I downloaded Armbian Noble 25.5.2 desktop onto my OPi5. It has been my daily driver for the past week or so. It has been a really nice release for my OPi5. All has been good except the default keyring popups. I have created new users, deleted stored keyrings, changed passwords among other things. At this point I am able to store the default keyring password (which is the same as my login PW). However, when launching chromium, and ProtonVP…

• 0

  Reputation Points

• 2 replies
• 2.4k views

SteeMan

July 24, 20242 yr

I tested boot time and node-red-reboot time and noticed that boot-time is with bookworm ~2 sec and node-red-reboot got from 14sec to 20sec. I hope you can improve performance so I can upgrade. https://paste.armbian.com/uhocorarad

• 0

  Reputation Points

• 0 replies
• 2.4k views

tim oberle

July 3, 20233 yr

Hi, I'm not sure if it is a bug as by board seems to work correctly, however I thought I should post it. In the latest version (5.10.60-rockchip64) I'm getting a few errors in dmesg: debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! I hadn't seen these errors in the previous version (5.10.43) Logs are here: http://ix.io/3yY5 Regards,

• 0

  Reputation Points

• 0 replies
• 2.3k views

Badger

September 15, 20215 yr

Trying to interface with a Raspbee II but the uarts dont seem to function, could this be correct?

• 0

  Reputation Points

• 1 reply
• 2.3k views

Werner

January 18, 20233 yr

For a fresh install of the latest desktop version for OrangePi5 I cannot get the system to run from NVME which is a Samsung 960 Pro. It gets stuck on the spinner at boot for the first-time boot after NVME using SD - NVME in armbian-installer. Any suggestions...

• 0

  Reputation Points

• 4 replies
• 2.3k views

royk

May 12, 20233 yr

After working in the ssh session for a while, the message suddenly appears: Broadcast message from user@rock-5c (Wed 2025-02-26 11:08:02 CET): The system will suspend now! Judging by the entries of journalctl, suspend is triggered in the kernel, not in systemd $ journalctl -b | grep -i suspend Feb 26 11:00:29 rock-5c kernel: rk806 spi2.0: dvs-suspend-control-by missing! Feb 26 11:00:29 rock-5c kernel: rockchip-dmc dmc: suspend_rate = 528000000 Feb 26 11:00:29 rock-5c kernel: rockchip-dmc dmc: deep_suspend_rate = 2112000000 Feb 26 11:00:29 rock-5c kernel: rockchip-pm rockchip-suspend: not set pwm-regulator-config Feb 26 11:00:29 rock-5…

• 0

  Reputation Points

• 0 replies
• 2.3k views
• 1 follower

pepperheart

February 26, 20251 yr

I haven't been able to find a step-by-step for enabling a USB OTG Network on the RockPi-S. Anyone have a link to the steps? I'm referring to the ability to connect a USB cable between the RockPi-S and a computer and be able to ssh or network to it. My usb port is in peripheral mode and I'm using Network Manager on Armbian Bookworm.

• 0

  Reputation Points

• 1 reply
• 2.3k views

Meestor_X

March 29, 20251 yr

Hi all, I'm trying to debug a sporadic problem with my Orange Pi 5 (16GB) which I'm unable to reproduce. I'm hoping maybe someone else experienced a similar issue or at least has any pointers on how to debug it further. The problem: At random times of the day, the board just appears to freeze up. All communications stop. Board is powered on, with red LED on and green LED off. I have to manually unplug the device to reset it. Within the last 2 weeks, this happened 3 times already. Each time, the last log appears to be a journalctl flush (example: https://pastebin.com/dDm5Xtis - the board froze at midnight, no more logs until …

• 0

  Reputation Points

• 1 reply
• 2.3k views

FL360

May 26, 20233 yr

Hey, I’ve read you can save 40Ma, can anyone tell me what is the best way of disabling HDMI? TIA

• 0

  Reputation Points

• 1 reply
• 2.3k views
• 1 follower

0jay

May 29, 20233 yr

Hello, i just bought new display from orangepi. But i have problem get it work with armbian 23 jally with kernel 5.15. I try get files from orange pi os with no success. Does somebody have working dts for this type of display ? Orange Pi RK3399 10.1inch LCD Touch Screen & Display Panel screen - OP1102 DTS

• 0

  Reputation Points

• 0 replies
• 2.3k views

jhofman

March 22, 20233 yr

Running Armbian Desktop stable 4.14y my Tinkerboard sees the WiFi network but refuses to connect. It has worked with TinkerOS so I don’t think it’s hardware related and Iknow the passcode and WPA settings look right. When I try to connect it spins and then fails after timing out. armbianmonitor -u output (with ethernet attached) http://ix.io/1x1J I’m probably just missing something stupid. Suggestions?

• 0

  Reputation Points

• 0 replies
• 2.3k views

WZ9V

December 29, 20187 yr

ubuntu22 Chrome://gpu The display report is soft processed!!!! How to configure it as hard processing？？？ help thank you.

• 0

  Reputation Points

• 4 replies
• 2.3k views

Igor

November 27, 20241 yr

Can you help me with the contents of the file name? I understand edge, vendor, but then there are other suffixes that are not clear to me: are gnome-oibaf_desktop the same "kernel release" as the xfce_desktop or minimal? Or there are patches that are applied only to a specific version? Thanks!

• 0

  Reputation Points

• 4 replies
• 2.3k views

ricardo_brz

May 27, 20242 yr

Hello everyone, I use my Orange Pi 5 board to run Open Media Vault with Wireguard installed. But there is a known issue with Wireguard that, when installing it, you have to manually reinstall the correct kernel into the board again, otherwise it won't be able to boot. However, ever since it has been installed, during apt update / apt ugrade of my board, it keeps recognizing the wrong kernel to be updated and changing the symlinks inside the /boot/ folder, rendering the board unbootable. If I see this happening, I can change the symlinks and it works normally after that. However, sometimes the symlinks changes unnoticed and I cannot boot anymore. I…

• 1

  Reputation Points

• 3 replies
• 2.3k views
• 1 follower

SteeMan

July 20, 20251 yr

Hy again :p; I have customed my sd for my tinkerboard. i have done some settings like eth0 in static, partitions modified scripts and hostapd. When i put it in another Tinkerboard, everything works except wifi ap. I have searched why, and i have found that in my initial tinkerboard wifi is wlan0 and his settings is in /etc/network/interfaces.d/armbian.ap.nat When i put my SD in another tinkerboard, it is wlan1 which mounts and no wlan0. Wlan1 has no ip address. i don't see where is the problem? thanks by advance

• 1

  Reputation Points

• 1 reply
• 2.3k views
• 1 follower

domoticity

February 26, 20197 yr

Good day, I have Opi 5 and bought this display https://www.aliexpress.com/item/1005005641383181.html?src=google&aff_fcid=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&aff_fsk=UneMJZVf&aff_platform=aaf&sk=UneMJZVf&aff_trace_key=66031a1404104c2cb62a43359c4edcd8-1705719622481-01990-UneMJZVf&terminal_id=b834b596955b44a1bf643629f5ba5647&afSmartRedirect=y . It was a blind buy ... And now I can't get it work if its even possible. I'm its my first time trying to get display on these boards usually use them trought Monitor or TV and it works flawlessly. Cant find even config.txt . But now im lost at how to get …

• 0

  Reputation Points

• 2 replies
• 2.3k views

ower

January 21, 20242 yr

Hi there, I have set up a tinkerboard S and I'm loving armbian so far. I only just encountered a weird problem. When i try to code in spyder3 there seems to be a messup in the keys i press and the key that is produced in spyder3. The funny thing is that this only occurs in spyder. When I type in terminal or gummi everything works fine. I am connecting to my TB using vnc using X. I've googled a bit around and found this could be a error of the XKEYBOARD as written here (I am however still not sure): https://github.com/spyder-ide/spyder/issues/3713 However I cant apply the proposed solution. I've found i need to go to /etc/X11/xorg.c…

• 0

  Reputation Points

• 0 replies
• 2.3k views

MEMEs

November 10, 20187 yr

My OS OS: Armbian (24.8.4) aarch64 Host: Radxa ZERO 3 Kernel: 6.1.75-vendor-rk35xx Uptime: 5 mins Packages: 1358 (dpkg) Shell: bash 5.2.21 Terminal: /dev/pts/0 CPU: (4) @ 2.000GHz Memory: 1168MiB / 7686Mi Reference Posts x2 I have this patch already in my /etc/systemd/journald.conf I edited /etc/default/armbian-zram-config -> ZRAM_PERCENTAGE=10 but allotment size didn't increase after a reboot (~47M before as well). By default this variable was commented out Filesystem Size Used Avail Use% Mounted on tmpfs 769M 24M 745M 4% /run /dev/mmcblk1p2 116G 32G 84G 28% / tmp…

• 0

  Reputation Points

• 1 reply
• 2.3k views

ioncube

June 29, 20251 yr

Hi ! I have a FriendlyElec NanoPi M5 and I want to play movies with it. But I want to squeeze everything out of this SBC ! So, I need hardware acceleration. I tested first with a OS image downloaded from FriendlyElec and mpv and (almost) everything works well. The mpv working configuration is: hwdec=rkmpp, vo=gpu, gpu-api=opengl. But I don't like that OS for other reasons, so I switched to Armbian. I installed the image "Armbian 26.5.1 KDE Wayland (Ubuntu 26.04 - vendor 6.1.115)", then I installed mpv, but when I try to play movies, it says: marus@nanopi-m5:/mnt/NAS/WDRed1/Samples/FullHD$ mpv --hwdec=rkmpp --vo=gpu --gpu-api=opengl H265.8bit.FullHD.192…

• 1

  Reputation Points

• 7 replies
• 2.3k views
• 1 follower

eselarm

July 8Jul 8

Can anyone tell me if it's possible to install renegade firmware on a Rasperry Pi build for example? Libre used to host a script for a tool that achieved this but it hasn't been updated since Buster TIA

• 1

  Reputation Points

• 5 replies
• 2.3k views
• 1 follower

0jay

November 27, 2025Nov 27

Not an issue nor a bug nor a trouble abour my Orange pi or Armbian. I wanted to build my "own" armbian for educational purpose. I mean to raise my knowledge. I followed this page. https://docs.armbian.com/Developer-Guide_Build-Switches/ however since it's done. I'm looking for about how to make the *.img file or if I can use *.deb located in my ~/build/output/debs I just miss these informations to finish and trying my failure compilation. I say failure compilation because "first time" is always a fail By the way, if I posted in the wrong place. Delete my post and please accept my apologies.

• 0

  Reputation Points

• 1 reply
• 2.3k views
• 1 follower

Werner

December 17, 20241 yr

Hello, The issue I describe below begins with a simple 1GB/s speed test with iperf3 (using tcp, then udp). With tcp everything is almost ok. With udp it's an other story. I first try through Internet and notice that there is connection drops. The network topology is : test computer => internet => router => switch (Mikrotik crs-326) => Rockpro64 The iperf3 server is on Rockpro64, and the client is on test computer. I then try to narrow down : - I connect directly to the switch and try again : in and out switch ports show near max speed (~1 Gbps), however the iperf3 server logs show 2 or 3 transfers at reduced speed, then show no tran…

• 0

  Reputation Points

• 0 replies
• 2.3k views
• 1 follower

arnaudf

August 19, 20233 yr

We have tried to connect the MIPI DSI 10.1 inch OPI Display. It is working fine alone but when we tried to connect another display with the HDMI. we expect it to work as our 2nd display but it did'nt work unless i disable the MIPI display from the OPI Config.

• 1

  Reputation Points

• 1 reply
• 2.3k views

ArmBoy1988

June 10, 20242 yr

There is no Orange Pi 5 results yet, but we can see already results of RK3588S. https://github.com/ThomasKaiser/sbc-bench/blob/master/results/Sorted-Results.md

• 0

  Reputation Points

• 0 replies
• 2.3k views
• 1 follower

MarcAndro

February 3, 20233 yr

If any of you have experienced skipping and popping when seeking with vlc, you can try setting the audio sink to ALSA and one of the rockchip-es8316 options. That will smooth out the audio playback BUT you will quickly discover that anything pulseaudio related is locked out of using the soundcard while vlc is up. Instead, try this. Set vlc audio back to pulseaudio (or automatic, seems to map to the same thing) and then change these two lines in /etc/pulse/daemon.conf: -; default-sample-rate = 44100 -; alternate-sample-rate = 48000 +default-sample-rate = 48000 +alternate-sample-rate = 44100 Restart pulseaudio with systemctl --user …

• 0

  Reputation Points

• 1 reply
• 2.3k views

Popolon

December 5, 2025Dec 5

Hi, I tried to connect an external USB 3.2 gen 2x2 4TB SSD drive to the only USB-C port available on the Rockpro64, but it's not recognized. I don't know if I need to install some packages for it to work? Any help would be very appreciated! I am on Ubuntu Jammy based Armbian: 6.1.63-current-rockchip64 #1 SMP PREEMPT Mon Nov 20 10:52:19 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux It works well with the same cable on a Macbook Pro. Kind regards, Baptiste dmesg [ 4.879030] usb usb1-port1: Cannot enable. Maybe the USB cable is bad? [ 4.880111] [drm] Initialized panfrost 1.2.0 20180908 …

• 0

  Reputation Points

• 1 reply
• 2.3k views

Baptiste

January 25, 20242 yr

Is there any existing solution how to use SPI2 on Radxa Rock Pi S? In dmesg I found these messages: [ 1.619008] rockchip-pinctrl pinctrl: pin gpio1-22 already requested by ff0c0000.serial; cannot claim for ff140000.spi [ 1.619046] rockchip-pinctrl pinctrl: pin-54 (ff140000.spi) status -22 [ 1.619065] rockchip-pinctrl pinctrl: could not request pin 54 (gpio1-22) from group spi2-miso on device rockchip-pinctrl [ 1.619082] rockchip-spi ff140000.spi: Error applying setting, reverse things back Is it somehow possible to disable the serial port which is in collision with the SPI? There is a log from armbian monitor: http://…

• 0

  Reputation Points

• 0 replies
• 2.3k views

Tomas77

June 20, 20233 yr

Hi guys. I have been using a RockPro64 as a miniserver for many years. It runs stable most of the time. I have assigned it a host name "ab2" via armbian-config. It usually responds well to this alias. Only from time to time it happens that it no longer responds to the hostname. Only a reboot helps. Do you have any idea what this could be? PS Thanks for your great work! Sem

• 0

  Reputation Points

• 1 reply
• 2.3k views
• 1 follower

CryBaby

February 23, 20242 yr

hi, ubuntu22 gome desktop How to fix USB sound card with card1 identifier 1

• 0

  Reputation Points

• 2 replies
• 2.3k views

lay

May 23, 20251 yr

I thought I had read that someone had the T2U working out of the box. Well, it's mostly there. When I tried it, didn't work. Got message in dmesg that firmware file not found. Did a Google search and found that it came down to the mediatek firmware files needing to be in the /lib/firmware/mediatek directory but they are currently in the /lib/firmware directory. FYI, the /lib/firmware/mediatek directory already existed and did not need to be created. Also in the current Jammy Gnome desktop Armbian, the file that was being loaded, mt7610e.bin, was not there and only the backup file, mt7610u.bin, was there in the /lib/firmware directory. What I d…

• 0

  Reputation Points

• 1 reply
• 2.3k views

bexem74332

October 17, 20232 yr

I created a deb package for my own application. How do I import it for compilation and installation?

• 0

  Reputation Points

• 1 reply
• 2.3k views

Werner

September 3, 20242 yr

The path '${kernelw_ork-dir}' actually exists, but why does it appear 'Cannon stat: No such file or directory' during compilation??? What are the configurations? For the convenience of personal development, I forced the use of my kernel source code git address. Please support me, thank you！！！

• 0

  Reputation Points

• 3 replies
• 2.3k views

lay

August 14, 20242 yr

is it possible to get edp on rockpro64 working with armbian

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

Hannes Campidell

October 26, 20223 yr

apt-get update / apt-get upgrad Armbian Xenial desktop mainline kernel 4.14, system failed to reboot and need a power reset to bring up. # uname -a Linux tinkerboard 4.14.34-rockchip #20 SMP PREEMPT Sun Apr 15 20:07:28 CEST 2018 armv7l armv7l armv7l GNU/Linux

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

Samson

May 17, 20188 yr

Last week installed Armbian for the first time on my Pinebook Pro that was basically bricked from Manjaro. Everything worked great! Audio is a little weak, but will look into that later. Today I pulled down the 25.2.1/6.12.16 update. On booting in Grub, I now get a message "Loading Device Tree Blob...", followed by "Error: not a regular file Press any key to continue". The boot then continues after a bit, and system seems to work fine from a user perspective after that (posting this from the machine). But there are some rockchip-pcie, rk3399-dmc-freq and brcmf errors in the armbianmonitor output (attached url) . I'm an Armbian noob, so dunno if the…

• 0

  Reputation Points

• 0 replies
• 2.2k views

namahsrob

February 25, 20251 yr

Hello, I've installed the 22.11 version with the 5.15 kernel on the microSD card. I've a rockpro64 with the SSD adapter and a WD black 250GB nvme. The system doesn't recognizes this drive. I've tested the latest stable ayufan image (kernel 4.4) and it recognises it perfectly. Should I downgrade the kernel to the 4.4 branch? Any help would be appreciated. Thanks,

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

jolosan

December 11, 20223 yr

I'm trying to install https://dl.armbian.com/orangepi5-plus/Bookworm_vendor_minimal in my Orange PI 5 Plus to the emmc but I've got a black screen after removing sd card.

• 0

  Reputation Points

• 2 replies
• 2.2k views
• 1 follower

Rdlop

September 2, 20242 yr

I have been working on rk3328 (kernel 6.1) based board recently and have been trying to bringup wifi RTL8723AS module using rockpi-e image. As there is no direct support available for this module I have tried to cloning it from github and building it but it gives compilation errors. Hence I referred to drivers available in the kernel and found one for the module similar to that of my module (RTL8723BS), cross verified through user manual and datasheets and build it using armbian. The driver gets built properly and even initializes upon powerup but it isn't getting into probe. The wifi is interfaced through SDIO to the board. Any idea what might b…

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

Bhavin

February 8, 20242 yr

The armbian can't support the third usb bus with pi5.But the official system debian runs normal to support the third usb bus.How to solve the problem?

• 0

  Reputation Points

• 2 replies
• 2.2k views

skyseedtb

January 7, 20233 yr

I have a nice video acceleration on chromium and Ubuntu noble, but not with a video player. Maybe someone can say one and how to install.

• 0

  Reputation Points

• 1 reply
• 2.2k views

maka

October 6, 20242 yr

Hello all! Not sure what is going on at all but I'm having a problem booting the "rolling release" of armbian (debian 14/forky) minimal cli. I'm using a nano pi R76S with 4gb of RAM and 64GB emmc. I can successfully burn a microsd for the previous version (also minimal cli vesion) which boots ok.However if I try to use the newer version nothing happens -- the red LED on the R76S stays permanently on and I get no display or any other life. I did try using different microsd cards but it did not make any difference. I also tried using the same microsd (I wrote the older version first to the microsd which boots) then wrote again on the sa…

• 1

  Reputation Points

• 7 replies
• 2.2k views
• 1 follower

SuperKali

May 21May 21

Hi, I have the board connected by HDMI to a TV but when I start I have no sound, I have to go to the speaker icon, configuration and the option is always selected "Speakers - internal audio" but if I want to have sound I have to choose the output option "Analogic ouput- internal audio" and if I restart I have to do the process again. According to the fine adjustment guide of ARMBIAN I must execute the command pacmd list-sinks | less And should be marked with * the selected card but none appears with that symbol. I attach the terminal output after selecting the right output on the desktop to have sound to see if someone is so kind to help me solve my problem. Thanks a…

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

Vidor

March 27, 20233 yr

Hi, after find out that the usb-connector right so have I tried install on a usb3-sata-m2 disk, I have problem to install. I created partision on the usb-disk with ambian-install, and after that trying to select 8 (download and install clean image), but it can't find any image for my board. I have no eMMC on my 4GB ram radaxa zero 3Wso I run from SD-card.

• 0

  Reputation Points

• 0 replies
• 2.2k views

Johan Nilsson

February 13Feb 13

Just interested if anyway has being able to set this up in Armbian yet? I had a brief look this morning but couldn't get it to work.

• 0

  Reputation Points

• 1 reply
• 2.2k views
• 1 follower

martivo

February 11, 20233 yr

Hello, I have installed the minimal Trixie based image for Orange Pi5 (the image named Armbian_26.2.1_Orangepi5_trixie_current_6.18.8_minimal) and then attempted to build an out-of-tree kernel module. Having installed dkms and build-essentials, plus the kernel headers through armbian-config, I found the headers package hasn't been fully set-up, the build symlink in /lib/modules/<KVER> is missing and dkms complains that the kernel headers for the kernel are not installed. The kernel headers are installed though, but it looks like they're from a previous release (25.11.2 instead of 26.2.1). # dpkg -l | grep rockchip ii linux-dtb-cur…

• 0

  Reputation Points

• 5 replies
• 2.2k views
• 1 follower

mitu

March 15Mar 15

Hi to all, In the past it was proposed by @Igor to use the u-boot-sunxi/remove-boot-messages-from-hdmi.patch this now as I can see under the allwinner-optional and seems do nothing on RockPro64 u-boot compile to hide the text @jock provided in the Tinker forum a userpatch disable-vidconsole.patch which works great on it (tinker) diff --git a/include/configs/tinker_rk3288.h b/include/configs/tinker_rk3288.h index bde7d72e6d..3ae9bb05f7 100644 --- a/include/configs/tinker_rk3288.h +++ b/include/configs/tinker_rk3288.h @@ -7,9 +7,9 @@ #define __CONFIG_H #define ROCKCHIP_DEVICE_SETTINGS \ - "stdin=serial,usbkbd\0" \ - "stdout=ser…

• 0

  Reputation Points

• 0 replies
• 2.2k views

2play

August 21, 20233 yr

Hi, SD card did not load Armbian_25.8.1_Orangepi5_trixie_current_6.12.41_xfce_desktop. I noticed that in boot.cmd line 9 , rootdev is defined as /dev/mmcblk0p1. Should that be /dev/mmcblk0n1 or /dev/mmcblk0n1p1? I note that this file should not be edited and the armbianEnv.txt only refers to rootdev=UUID=7e27c862-0a39-41cd-891e-7d77ff7968fd. Is this an error or am I off course? If so where do I correct it? cheers

• 0

  Reputation Points

• 4 replies
• 2.2k views

mcfo

October 5, 20251 yr

I have installed Armbian 25.02 via an official Armbian image for Armbian 25.02 (Debian 12) Vendor Kernel 6.1.xx, is it possible (and sane) to upgrade to Armbian 25.05 (Debian 12) Vendor Kernel 6.1.xx? If so besides downloading the new image and installing fresh what are one's options?

• 0

  Reputation Points

• 1 reply
• 2.2k views

SteeMan

April 29, 20251 yr

Hi, I've been compiling my own Armbian images since 6.13-rc5, and now 6.13 and I noticed that when I compile i3, youtube videos and webgl tests don't work as great when I compile i3 with mesa-vpu as it does when I compile e.g., cinnamon. I also noticed that the suffix is not -mesa-desktop, only -desktop. Is it as per design and i3 doesn't include mesa at all, or is it some kind of bug? Thanks!

• 0

  Reputation Points

• 1 reply
• 2.2k views

ricardo_brz

January 28, 20251 yr

I've setup the pwm overlay but while it shows up the pwm devices in /devices - it is missing the pwm0 control I've read couple posts where ppl have been able to override the overlays by decompiling the original one, but I can't make sense of the dtc dtb dtbo and dtsi files 😕 Any guides or other suggestions to fix the pwm control? Temperature and fan control on OPI5 - Orange Pi 5 / 5B / 5 Plus - Armbian Community Forums Rock Pi4 pwm control - no overlay? - Rockchip - Armbian Community Forums

• 0

  Reputation Points

• 1 reply
• 2.2k views
• 1 follower

OttawaHacker

July 23, 20233 yr

With the vendor kernel, my logs are getting flooded with drm error messages Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:rockchip_vop2_mod_supported] *ERROR* Cluster0-win0 unsupported format modifier 0x800000000000062 Apr 13 17:04:05 kitchen-opi kernel: [drm:r…

• 0

  Reputation Points

• 2 replies
• 2.2k views
• 1 follower

OttawaHacker

April 18, 20251 yr

Hi folks, Ran into some issues with July 6 bookworm images for Orange Pi 5 Plus - it boots but there is no video or network. Orange Pi 5B has a note to change the dtb - one is also needed for the 5 Plus. It should be `fdtfile=rockchip/rk3588-orangepi-5-plus.dtb`. (I tried to search for related issues, but the rate limit is stopped me so I gave up.)

• 0

  Reputation Points

• 1 reply
• 2.2k views

Efe Çetin

August 10, 20233 yr

Does the khadas EDGE2 ARMBIAN system support Mali GPU by default?

• 0

  Reputation Points

• 2 replies
• 2.2k views

lay

August 28, 20242 yr

Well, I am trying to flash armbian to my board, but after I run upgrade_tool ef in mistake. I can't do anything via maskrom/loader at all wherever Windows or linux. Then I try to unbrick it via flash the "MiniLoaderAll.bin" via "upgrade_tool db" and "ul" but them don't work at all(Timeouted),How can I do with it?

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

calvin lin

March 2, 20242 yr

I had use QML to made some soft, and when i move those soft to Tinkerboard, it's Incredibly slowly... have any idea to fix this? did tinkerboard had open gpu acceleration? do i must change back to use QtWidget?

• 0

  Reputation Points

• 0 replies
• 2.2k views

aitek

November 12, 20187 yr

Is there any trick to make use of the integrated fan on Radxa 25W PoE Hat? I'm using 4GB Radxa Rock 5C Lite Armbian_25.5.1_Rock-5c_bookworm_vendor_6.1.115_minimal Some guides mention that one should enable an overlay. I didn't find any relevant overlays in armbian-config. In the Radxa repo I found rock-5a-radxa-25w-poe.dts which specifies that it's also compatible with Rock 5C. I've compiled it and enabled it, but by default the fan is not spinning (on high temps) and I'm not sure how to investigate that. Also, does it matter that I have 5C Lite? As it has another chip: RK3582

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

Uko

June 26, 20251 yr

On my Odroid M1 I have a display that will not work, other displays do work. Unfortunately, I need this display to work. When I plug it in, I see "PHY PLL not locked" in dmesg. If I boot with it plugged in, I see the Hard Kernel logo, then the screen turns off as Armbian boots. I booted into the Ubuntu 20.04 Gnome image provided by HardKernel and that one works. 1. What could I change to allow this display to be detected? 2. Can I just force the board to boot with output to 1024x768@60. I just need the output. Thanks all.

• 0

  Reputation Points

• 0 replies
• 2.2k views
• 1 follower

JohnCHarris

May 12, 20233 yr

Every time I stop and then start Chromium, do a search on google, or on youtube, there seems to be a deletion of the cookies, and it asks consent again, login again .... I found lots of possible solutions on internet about that issue, but none work for me! I wonder what this is due to, any ideas?

• 0

  Reputation Points

• 2 replies
• 2.2k views

Tony3

September 18, 20233 yr

Hi, I wanted to give my Odroid M1 new life by installing a fresh Armbian 25.5.1. Previously it was running on an old Odroid Ubuntu Image. After starting from SD I have no ethernet connection. The eth0 interface is DOWN. I tried using a USB3 2.5G ethernet adapter, but the new network interface also shows DOWN. I have tried Debian and Ubuntu Minimal images with the same results. What could be the cause and how do I get a working ethernet connection? Thanks Malz

• 0

  Reputation Points

• 1 reply
• 2.2k views

Malz

June 5, 20251 yr

Where were the scripts for the 'update_initramfs' and' mkinitramfs' tools generated? I couldn't find it in the package. Please help me, thank you！

• 0

  Reputation Points

• 2 replies
• 2.2k views

eselarm

November 29, 20241 yr

The apt source is always overwritten by the cache source when modified. How can I modify this cache source. How can I modify this cache source?? help help

• 0

  Reputation Points

• 1 reply
• 2.2k views

Werner

August 29, 20251 yr

Hello, After several days of debug I put the finger on a very strange issue using integrated Ethernet. I use my Rockpro64 mostly as a Samba and DNS server. In my network context I implement 2 vlans as vlan interfaces (eth0.10 and eth0.20). Each of these interfaces needs to use a specific mac address that differs from physical eth0 mac address (it is an important point). If I use only the physical mac my router is not be able to route correctly between vlans (probably an ivl/svl issue). Under this context I first noticed that when I bring down eth0.20 although using vlan 10 (so eth0.10) connectivity is lost. I then wr…

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

arnaudf

June 21, 20242 yr

Hello, I have a problem with mounting a USB HD via fstab. If I enter the HD in the fstab, the system hangs when booting. The problem, USB is not activated yet and will be loaded later. If I remove the HD from fstab, it is automatically mounted under /run/media/USER. However, this must not be mounted under a user, but should be mounted as root. What can I do. Thanks very much

• 0

  Reputation Points

• 2 replies
• 2.1k views

amielke

February 9, 20233 yr

Hi, How can i get the Rknpu working in Armbian for latest builds. I am unable to find how to make this work. Thanks in Anticipation

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

Rajiv Singh

August 18, 20242 yr

May I know how do you enable Panrost support Ubuntu 24.04 on Khadas Edge2? By Khadas SDK, I have built image which failed with followings: 1. Enabled Panfrost in defconfig. 2. Add kisak-mesa ppa, apt update and upgrade. 3. Replace mali_csffw.bin by Armbian mali firmware. After these, the gnome-settings shows the GPU is software vendoring. Hope to get your help~ Thanks!

• 0

  Reputation Points

• 0 replies
• 2.1k views
• 1 follower

Jacob Zang

August 22, 20242 yr

Hey! I recently got a CAN-bus up and running on a Tinkerboard running Armbian, but I've run into another problem here: The CAN-bus buffer fills up. After sending a few messages I get an error saying "No buffer space available". I've noticed that some other people are solving this by increasing the buffer size, but that seems like a weird solution to me. And it wouldn't really help me much. I need to empty this buffer when I read from it, or manually (without restarting the CAN-bus). Any ideas on how to do that? Thanks

• 0

  Reputation Points

• 0 replies
• 2.1k views

Marius Brataas

February 21, 20188 yr

Hello Guys. สมัครสมาชิกufabet เว็บพนันบอลต่างประเทศ I want to extend the current kernel (Tinkerboard with rockchip-kernel-4.4.120 on Debian-Armbian) to include IR (GPIO) and DVB modules. What do I have to consider or is this possible with the usual run-through? (copy .config from current system, make menuconfig, make, sudo make install, sudo make modules_install) Is there possibly already a tutorial that I have not seen?

• 0

  Reputation Points

• 0 replies
• 2.1k views

roroeow8

March 25, 20197 yr

Hey there, I now have my Nanopi R4S for quite a while but never got it to run stable over a longer period of time. Now I finally connected another board to its debug serial in the hopes to catch something that causes the board to freeze. Well this is what I have collected: https://p.na4.eu/?bc818aefadc9b5b2#DAunYKXghkaqcLhh8SLWMKTWABewpwPJRnHMHDemR98Y The log is complete, there is nothing missing between 08:51 and 19:14. This is how I collected it. Basically during the state of throwing errors the board becomes unresponsitive and continously heats up. Active cooling was in place so no danger of overheating. https:/…

• 0

  Reputation Points

• 0 replies
• 2.1k views

Werner

April 10, 20233 yr