Rockchip

Hi all I hava an orange pi 5 plus with a 512GO NVME SSD. I have installed the latest version od Armbian to a SD card it work well, but for speed reason i would like to install the OS to th SSD drive and boot from this device and no longer from the SD card. Is there a way to do this ? i mean from u-boot point of view? i can keep a SD card inside it to store u boot but i would like to move usr var and such to SSD Thanks in advance for your answers comment or ideas W.

• 0

  Reputation Points

• 3 replies
• 4.9k views
• 1 follower

William Bonnet

June 13, 20242 yr

I purchased this board to use as a gaming station and, among the options, I'm using moonlight with sunshine to stream my steam to the room, which is working wonderfully well, but I'm having a problem. When pairing the control with Armbian, it is recognized as a joystick but I cannot use it in any way. I have two Sony Dualsense joysticks, I tested them both with cable and Bluetooth and the problem is the same. Can anyone guide me where I can start to debug the problem? NOTE: I borrowed an IPEGA joystick and it worked normally. [ 1107.997887] playstation 0005:054C:0CE6.0007: unknown main item tag 0x0 [ 1107.998309] playstation 0005:054C:0CE6.0007: hidra…

• 0

  Reputation Points

• 3 replies
• 4.9k views
• 2 followers

sunarowicz

June 20, 20242 yr

Is there a way to upgrade from an earlier version to 5.41?

• 1

  Reputation Points

• 8 replies
• 4.8k views

Jose Deras

March 28, 20188 yr

Please post complaints, as of my latest build I'm getting the link drops as well.

• 1

  Reputation Points

• 4 replies
• 4.8k views

TonyMac32

May 15, 20188 yr

Hello, compiling Kernel 5.4.40 (setting in lib.config with KERNELBRANCH=tag:'5.4.40') under Vagrand with RT-Patch "patch-5.4.40-rt24.patch" putting in " ~/build/userpatches/kernel/rockchip64-current/ "for RockPro64 fails. ........ [ o.k. ] * [l][c] general-rt5651-add-mclk.patch [ o.k. ] * [l][c] mp8859-kbuild-makefile.patch [ o.k. ] * [c] patch-5.4.40-rt24.patch [ o.k. ] * [l][c] rk3328-add-dmc-driver.patch [ o.k. ] * [l][c] rk3328-audio-and-renegade-supplies.patch [ o.k. ] * [l][c] rk3328-clean-up-codec-gpio-SD.patch [ o.k. ] * [l][c] rk3328-fix-wrong-mmc-shift.patch [ o.k. ] * [l][c] rk3399-add-sclk-i2sout-src-clock.patch [ o.k. …

• 0

  Reputation Points

• 6 replies
• 4.8k views
• 1 follower

martinayotte

May 27, 20206 yr

Hello i hope you all have a nice day At first i need to thank you for all the work you done. I'm runnig my ROCKPro64 no for a while now Today i wanted to try wifi and bt but it looks we dont have any drivers for the module AMPAK AP6256 Combo Module and made specifically for the ROCKPro64 Debian 10 headless 20.08.0-trunk Can someone help me to reach the goal to use my wifi ?

• 0

  Reputation Points

• 2 replies
• 4.8k views

max12m3

July 13, 20206 yr

I just download Armbian_20.11.6_Tinkerboard_bionic_legacy_4.4.213_desktop.img.xz flased it on sd card with balenaEtcher, tried to boot and got error: So. I can't do my first login.

• 1

  Reputation Points

• 8 replies
• 4.8k views

Igor

January 20, 20215 yr

So I have armbian installed on a tinkerboard and have had absolutely no issues with it until I bought a new Samsung 7000 series TV (2019). For some reason this TV does not recognize the signal coming from the tinkerboard. For the life of me I cannot figure out how to get this to work. I notice a few references online about being able to force a resolution but nothing related to the rockchip boards. Is there an equivalent way to force a display resolution as in this article? https://docs.armbian.com/Hardware_Allwinner/#how-to-reconfigure-video-output I'm running 4.19.21-rockchip 5.76 I've also tried kernel 5.4.28 as well an…

• 1

  Reputation Points

• 5 replies
• 4.8k views

Myy

May 9, 20206 yr

For a few weeks I've been using the latest official release from May 26, 2025, running just fine from my NVME drive. But then I turned it on and at the screen where you get the Amrbian grey/red logo in the middle of the screen and the spinning circle, it went no further. The spinning circle would either stop rotating or disappear after a minute or so. I can SSH into the device. But when I use remote desktop from a Windows PC, the full and functioning desktop is there. It's just not on my TV screen any more. I've done the usual HDMI cable testing and powering off the TV completely, but no change. The fact that the…

• 0

  Reputation Points

• 9 replies
• 4.8k views
• 2 followers

compent

July 6, 20251 yr

Hello, I've used the Tinkerboard S (Rockchip RK3288) with the Armbian images available for download (https://www.armbian.com/tinkerboard/). Currently, the /dev/ttyS4 serial port is not available unless CONFIG_SERIAL_8250_NR_UARTS=5 when the Linux kernel is built since the serial ports are populated in /dev starting with /dev/ttyS0 and the last serial port to be populated is /dev/ttyS4. By default, CONFIG_SERIAL_8250_NR_UARTS=4. Some additional kernel settings are required to ensure that all of the available serial ports can be utilized. Moreover, I had to activate I2C4 in the device tree overlay using the Armbian configuration utility (https://docs.armbi…

• 1

  Reputation Points

• 6 replies
• 4.8k views
• 2 followers

nkinar

March 27, 20224 yr

Hi, New build, Armbian_21.05.0-trunk_Tinkerboard_focal_current_5.10.22_xfce_desktop.img. The build finished ok and the image after flashing is working just fine, but.. unfortunately there is no /boot/dtb/overlay folder and of course none and its .dtbo entries are found anywere. Am I missing something ? Is the latest build system broken for Tinkerboard ? Do I need to specify something during the build process menu ? /PS Just checked with the Armbian ready-made provided image for Tinkerboard, the Armbian_21.02.1_Tinkerboard_focal_current_5.10.12_desktop.img.xz and Armbian_21.02.3_Tinkerboard_…

• 0

  Reputation Points

• 3 replies
• 4.8k views

Christos

March 11, 20215 yr

hi , i am using the gpio library provided by asus tinker board to work with gpio on armbian os . i am having issue with running the python script without giving sudo cmd. is there any alternative to overcome giving sudo all the time while running gpio python script or any other alternate library to use with armbian python add_event_callback.py can't open /dev/mem and /dev/gpiomem wiringPiSetup: Unable to open /dev/mem and /dev/gpiomem: No such file or directory Segmentation fault

• 0

  Reputation Points

• 4 replies
• 4.8k views

Yuvaram Singh

March 8, 20188 yr

Quick question, what happened to Debian Stretch images for Renegade, it seems there is only ubuntu images for download now. Does armbian perfer ubuntu rootfs for server images now?

• 0

  Reputation Points

• 5 replies
• 4.8k views

sfx2000

September 22, 20188 yr

Hello, I have Tinker Board. If I install Armbian I see screen only over HDMI. I would like to enable DSI touchscreen display. Is it possible? How make it? Thank you

• 0

  Reputation Points

• 1 reply
• 4.8k views
• 1 follower

TonyMac32

June 25, 20179 yr

Hello, I'm quite new to SBC and linux. On one hand I'm learning a lot, but on the other hand I'm struggling to make it work as I would like. I already have a low performance Zimaboard (just 2GB Ram) that I use as a NAS and I want the ROCK 5 ITX 8GB to be used as a general purpose apps server for home automation, streaming music, listening music, etc. One of my use case I'm playing with is the following: 1) music files are on the NAS 2) Music files are played from the Rock5 ITx via the speakers plugged into the headphone jack, 3) The music player is controlled remotely using Lyrion Music Server + Squeezelite. I've already tested t…

• 1

  Reputation Points

• 3 replies
• 4.8k views

Bobbox

April 15, 20251 yr

I have Orange Pi 5 Plus that I plan to install in a remote location. To boot Orange Pi, I need to press the physical Power On button. How I can setup the machine to boot automatically once the power is supplied? There is nobody on the remote side to press this button. Or maybe there are other options to boot remotely like WakeOnLAN? Where it can be configured? In orangepi-config?

• 1

  Reputation Points

• 5 replies
• 4.7k views
• 1 follower

Werner

December 9, 20241 yr

My application creates 15 threads. Since A53 has 4 cores it is likely that more threads will be spawned by A53. Is there a way to manipulate scheduling and create more threads through cortex A72 so that it compensates the delay. Examples 6 threads on A72 and 9 threads on A53. This way it ensures the run time does not fluctuate and we achieve peak performance.

• 0

  Reputation Points

• 6 replies
• 4.7k views
• 2 followers

jock

June 28, 20188 yr

I connected a tinker to a 4k tv and the highest resolution that armbian offers is 1920x1080. What could be the reason that 4k res is not offered? I'm using ARMBIAN 5.43.180417 nightly Ubuntu 16.04.4 LTS 4.14.34-rockchip.

• 1

  Reputation Points

• 9 replies
• 4.7k views

freak

April 19, 20188 yr

ubuntu22 gnome desktop Hi, may I ask how to install Google Chrome

• 0

  Reputation Points

• 1 reply
• 4.7k views

Igor

November 26, 20241 yr

This is a new release of the uefi firmware for Orange Pi 5 Plus which now has mainline kernel support. My thought was that this new release would support armbian uefi builds but so far no love. Does anyone know of an armbian build that would work with this??? The is the one of the tag lines from readme.md found @ https://github.com/edk2-porting/edk2-rk3588 "It delivers a PC-like standardized boot experience, supporting multiple operating systems, such as Windows, Linux, BSD and VMware ESXi."

• 0

  Reputation Points

• 2 replies
• 4.7k views

Hooutoo

December 28, 20241 yr

The NanoPi R3S contains a hardware clock (HYM8563) with the possibility to connect a backup battery. However, the current kernel adds this clock as an additional one (RTC1). I tried to create a device tree overlay, but it does not work. As I understand it, this is because the default Rockchip clock is not included in the device tree. So, if I understand correctly, the only way to make the HYM8563 the default clock is to build the kernel with this option enabled. Please consider changing the default kernel options to make the HYM8563 the default RTC. If there’s another way to make the HYM8563 the default RTC, please advise.

• 0

  Reputation Points

• 9 replies
• 4.7k views

c0rnelius

August 26, 20251 yr

Hi out there! I've managed to build a quite complex system based on Tinker, using 1 Wire sensor, I2C-s, all of all UART's, and all of all remaining GPIO's... :-) Unfortunately a long term test in a climate chamber have failed... (although the core was just heated up to 70 degrees Celsius) The need for a hardware watchdog then arise... I've build new kernel using latest compile.sh with the HW watchdog checked resulting Linux tinkerboard 4.4.110-rockchip #2 SMP Wed Jan 10 16:41:03 CET 2018 armv7l GNU/Linux but there is no /dev/watchdog Not even in /proc/iomem at ff800000... …

• 0

  Reputation Points

• 2 replies
• 4.7k views
• 1 follower

TonyMac32

January 11, 20188 yr

Hello, I'm using a RockPro64 boards inside one of my projects and I just noticed an issue related to the reset process. When pushing the reset button, the boards hangs in a reset loop. Using the oscilloscope, I found that the reset signal (OTP_OUT_H) is toggled every 330ms by the CPU and the only way to get it back to work is to power off the board, wait a few seconds, and power it back. The same issue is found if, after a working boot, a quick power cycle is performed. I tried disconnecting everything from the board but still, when pushing the reset button, the boards hangs in a loop condition (as if it’s constantly crashing at boot). …

• 0

  Reputation Points

• 5 replies
• 4.7k views

martinayotte

November 8, 20196 yr

When connected to some PC monitors, the image is larger than the physical screen: about 20 pixels at the top and bottom sides, and 50 pixels at the right and left sides are missing. This happens as soon as the board boots (without logo), the start of lines are truncated, and this also happens on text ttys (Ctrl + Alt + F1..6). I guess it's about a boot env variable, but I could not find it.

• 0

  Reputation Points

• 7 replies
• 4.7k views

bolet75

June 24, 20242 yr

Unfortunately, there seems not yet to be an area in this forum for NanoPi R6C/S, so here we go ... Here is the default Armbian /etc/udev/rules.d/70-persistent-net.rules SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", KERNELS=="fe1c0000.ethernet", NAME:="wan" SUBSYSTEM=="net", ACTION=="add", DRIVERS=="r8169", KERNELS=="0003:31:00.0", NAME:="lan1" SUBSYSTEM=="net", ACTION=="add", DRIVERS=="r8169", KERNELS=="0004:41:00.0", NAME:="lan2" This does not match up with the labels on the case! Here is the correct config we have updated and tested on a NanoPi R6S at Afritic Group: SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*"…

• 0

  Reputation Points

• 11 replies
• 4.7k views

eselarm

July 23, 20251 yr

Hello, my Orange Pi 5 works well with the stock OS (1.22, Ubuntu Jammy, BSP kernel 6.1.99), using the SD as a boot device. It also works ok with Armbian Minimal-IoT / Debian 13 / 6.1: v25.8.2 for Orange Pi 5 running Armbian Linux 6.1.115-vendor-rk35xx But I prefer Ubuntu and wanted to try 6.12, so I downloaded 25.8.2 / Ubuntu Server / 6.12. Wrote to SD, hooked up the debug UART and powered on. The bootloader is fine, the kernel starts, but at a certain point it panics: [ OK ] Reached target sockets.target - Socket Units. Starting armbian-hardware-monitor.…ce - Armbian hardware monitoring... …

• 0

  Reputation Points

• 7 replies
• 4.7k views

XFer012

December 1, 2025Dec 1

I want to install Armbian on Nvme SSD. How do I install on SSD?

• 0

  Reputation Points

• 4 replies
• 4.7k views

Guest

February 1, 20233 yr

ubuntu22 desktop Why does the system restart trigger at 3:30 every day？？ I used 'uptime'to check the changes in running time！ How to turn off the trigger！ sudo grep "3:3[0-9]" /var/log/syslog | grep -i "unattended\|reboot" Sep 19 03:30:53 armbian-ramlog[451]: unattended-upgrades/ Sep 19 03:30:53 armbian-ramlog[451]: unattended-upgrades/unattended-upgrades-dpkg.log Sep 19 03:30:53 armbian-ramlog[451]: unattended-upgrades/unattended-upgrades-shutdown.log Sep 19 03:30:53 armbian-ramlog[451]: unattended-upgrades/unattended-upgrades.log Sep 19 03:30:53 cron[604]: (CRON) INFO (Running @reboot jobs) Sep 19 03:30:54 systemd[1]: St…

• 0

  Reputation Points

• 2 replies
• 4.7k views

SteeMan

September 19, 20251 yr

Hi, I can not get the back panel audio working, the HDMI analog audio to my display works, but changing the output to Analog out is not working. Any suggestions as to where I can start to troubleshoot? Thanks!

• 0

  Reputation Points

• 11 replies
• 4.6k views
• 1 follower

prahal

May 16, 20251 yr

Hi! On the Rockpro64, with the latest Amrbian dev kernel (5.4.0-rc1-rockchip64 updated on 19th of January), the sata hard drive connected to PCIe through the pine store adapter does not go to sleep anymore. It is properly set with hdparm and a udev rule, it used to work fine with the dev kernel before the 19th of January update. Now, if I issue a sleep commd (hdpram -y /dev/sda) it goes to sleep properly but not by itself after the 5 minutes inactivity I have set up. Mathias

• 1

  Reputation Points

• 5 replies
• 4.6k views
• 1 follower

Mathias

April 16, 20206 yr

running 24.8.3, and Armbian-install's screen looks like this: Current root: UUID=117b851b-2be0-4bb7-8572-7edce1ef7375 SD card (/dev/mmcblk1) 1 Boot from SD - system on SATA, USB or NVMe 2 Boot from - system on 3 Boot from - system on SATA, USB or NVMe 5 Install/Update the bootloader on SD card (/dev/mmcblk1) I have a µSD card inserted and a 4gb eMMC, but it looks like the names of these devices are missing?

• 1

  Reputation Points

• 11 replies
• 4.6k views
• 1 follower

Meestor_X

January 1, 20251 yr

Hi, I went to see if there were any updates to the OPi5+ images and saw the OPi5 had updates. I clicked on the link on the main download page. https://www.armbian.com/orangepi-5/ https://redirect.armbian.com/orangepi5-plus/archive/ I've come back and now it has desktop images but no server images.

• 0

  Reputation Points

• 8 replies
• 4.6k views

Werner

February 16, 20242 yr

I got a radxa rock 5t and trying to install armbian(https://www.armbian.com/radxa-rock-5t), arimbian NOT boot and I can see the indicator light on the board is showing a steady green light. I boot with the official image https://docs.radxa.com/en/rock5/rock5t/low-level-dev/maskrom/linux and insert the sd card(with armbian img), and run such command, then I can boot armbian from SD card sudo dd if=/dev/mmcblk0 of=working_idbloader.img bs=512 skip=64 count=8000 sudo dd if=/dev/mmcblk0 of=working_u-boot.itb bs=512 skip=16384 count=8000 sudo dd if=working_idbloader.img of=/dev/mmcblk1 bs=512 seek=64 conv=notrunc sudo dd if=working_u-boot.itb of=/dev/mmcblk1 bs…

• 0

  Reputation Points

• 5 replies
• 4.6k views
• 2 followers

laibsch

August 8, 20251 yr

I need to move my homeassistant from rpi4 to an opi5 but I have some I2C sensors connected. Had anyone any luck configuring python and gpio to work with I2C sensors? This was a bit rough a while ago and the kernel support seems much more limited compared to the rpi4 for this type of use case. Any experience?

• 0

  Reputation Points

• 4 replies
• 4.6k views
• 1 follower

martivo

August 31, 20233 yr

Greetings, I recently had a request about testing the I2S and SPDIF output of MiQi devices and after some fiddling on this board, it seems that the Rockchip I2S + Simple-Audio ALSA driver just output nothing on the I2S TX/RX pins, at least. So was anyone able to output sound directly through the I2S GPIO pins on any RK3288 device ? Tinkerboard devices seems to use that setup and it seems to be working, but I'd like to know if that's working through the soldered Jack or the GPIO.

• 0

  Reputation Points

• 10 replies
• 4.6k views

nitroshift

March 14, 20188 yr

Hi everyone! I am struggling with audio input. Output audio from LINEOUT pins works fine out-of-the-box! What about the audio input? To begin with I have tested the arecord command with these error messages… TEST 1 root@rockpi-s:~# arecord -f S16_LE -d 10 -r 16000 --device=“hw:0,0” test-mic.wav Recording WAVE ‘test-mic.wav’ : Signed 16 bit Little Endian, Rate 16000 Hz, Mono arecord: set_params:1358: Channels count non available TEST 2 root@rockpi-s:~# arecord -f S16_LE -c 2 -d 10 -r 16000 --device=“hw:0,0” test-mic.wav Recording WAVE ‘test-mic.wav’ : Signed 16 bit Little Endian, Rate 16000 Hz, S…

• 0

  Reputation Points

• 4 replies
• 4.6k views

PHLAK

May 19, 20251 yr

Not sure if the rolling release includes the UART dtb yet, but when I build my own image (jammy xfce kernel 5.10.110) I don't have the UART dtbs in /boot/dtb/rockchip/overlay/ . As a result, I couldn't add uart0-m2 to /boot/armbianEnv.txt and get /dev/ttyS0 when I was following the official user manual to enable UART. After some researching I managed to solve this by copying the dtb file from orange pi's official ubuntu image to /boot/overlay-user and enable UART with user_overlays=rk3588-uart0-m2 in armbianEnv.txt . Rebooted and it works. However, I suppose it would be better to include the dts files in kernel patches? I'm posting this because I don't know what…

• 1

  Reputation Points

• 1 reply
• 4.6k views

Efe Çetin

January 18, 20233 yr

Hi! I installed this image on my Khadas Edge 2 Armbian 24.5.5 Noble Gnome MESA / VPU I am wondering if it is possible to use Wacom tablet. I have seen Ubuntu builds from Khadas support it. Another question is about 1440p monitor using hdmi port on Edge 2, newer Ubuntu development builds seem to have this option, what about Amrbian?

• 1

  Reputation Points

• 9 replies
• 4.6k views

Efe Çetin

September 2, 20242 yr

Hi everybody, I have a problem with this version: Armbian_20.05.2_Rockpro64_buster_legacy_4.4.213.img I don't see my disk that is plugged on the PCIe To SATA Marvell 88SE9230 in the system. I've create the file /etc/udev/rules.d/99-marvell.rules with the following line on it: ACTION=="add", SUBSYSTEM=="pci", ATTR{vendor}=="0x1b4b", ATTR{device}=="0x9230", RUN+="/bin/bash -c 'echo %k > /sys/bus/pci/drivers/ahci/bind'" If I do the same thing with this version: Armbian_20.05.4_Rockpro64_focal_current_5.4.46.img, I see my disk after creating the file. But, there's two problem with this version: first the fan always running and, m…

• 0

  Reputation Points

• 2 replies
• 4.6k views
• 1 follower

AndrewCo

May 26, 20242 yr

Hello, I am using the latest Desktop Armbian and use the internal wifi and a usb wifi stick (edimax ew 7811-un). Both devices are detected by network-manager. I use network-manager to connect to my router. I get internet. Minutes later, there is DNS conflict (/var/log/syslog) and I cannot resolve any websites anymore. I only see dhclient DHCPDISCOVER on eth0 255.255.255.255 for some reasons. I have this problem with a fresh installed Armbian. How can I solve this? Thank you

• 0

  Reputation Points

• 4 replies
• 4.6k views

tkaiser

December 22, 20178 yr

Looking for information on enabling 4 wire SPI on the Libre Renegade. I think have it enabled (spi-spidev) in armbian-config and I think configured correctly in /boot/armbianEnv.txt: param_spidev_spi_bus=0 param_spidev_spi_cs=0 param_spidev_max_freq=1000000 Connecting to pins GPIO pin# 19/21/23/24 I still do not see ANY devices matching /dev/spi* - An guidance as to WHY? I have the build framework, but am new to building armbian kernels but could navigate it with some direction. TIA folks! [Trying to connect a 240x320 LCD display using the ST7789-VW controller, not using Arduino IDE]

• 0

  Reputation Points

• 4 replies
• 4.6k views
• 1 follower

TonyMac32

October 3, 20233 yr

@Igor@amazingfate Can someone look at this issue please ? I am wondering if this is possibly affecting a large number targets or whether its just BananaPi-M7 / rockchip64 ? I have tried on another monitor also and am getting a black screen. On doing an `apt-get upgrade` on ssh terminal I happened to loose by HDMI display. AFAICT It looks like Ubuntu 'backgraded' gnome v46 (in Nobel release, and also in my older unofficial image) to v44. https://armbian.atlassian.net/jira/software/c/projects/AR/issues/AR-2702?jql=project %3D "AR" ORDER BY created DESC

• 1

  Reputation Points

• 19 replies
• 4.6k views
• 1 follower

MaxT

July 19, 20251 yr

I am Running Armbian 24.5.1 Jammy with Linux 6.1.115-vendor-rk35xx on Radxa Rock5b (and it works great!!) when running sudo apt dist-upgrade or sudo apt upgrade I get Die folgenden Pakete sind zurückgehalten worden: armbian-bsp-cli-rock-5b " Packages retained" apt list --installed | grep armbian-bsp-cli-rock-5b gives: armbian-bsp-cli-rock-5b-legacy/jammy,now 24.5.1 arm64 [installiert] armbian-bsp-cli-rock-5b/jammy,now 24.5.1 arm64 [Installiert,aktualisierbar auf: 25.5.1] ## installed, can be updated can/shall I force the the use of "armbian-bsp-cli-rock-5b/jammy,now 24.5.1 arm64 [Installiert,aktualisierbar auf: 25.5.…

• 0

  Reputation Points

• 8 replies
• 4.6k views
• 2 followers

robertM

August 4, 20251 yr

Hi I installed a nvme SSD to my rockpro64 (with a generic PCIe adapter card). Somehow it only uses a x1 link instead of x4. I also observed the same behaviour with a x2 SATA card (only x1 link established). Output of lspci: LnkSta: Speed 2.5GT/s (downgraded), Width x1 (downgraded) To rule out hardware issues, I also tried the same setup with Manjaro-ARM which correctly negotiates a x4 link. LnkSta: Speed 2.5GT/s (downgraded), Width x4 dmesg for Armbian [ 2.221206] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges: [ 2.221296] rockchip-pcie f8000000.pcie: MEM 0x00fa000000..0x00fbdfffff -> 0x00…

• 0

  Reputation Points

• 4 replies
• 4.6k views

Nino

May 30, 20242 yr

Hello, I read about raxda zero3E edge support, and because I'm having problems with img-6.12.9+bpo-arm64-16k (wireguard dependency) Do you think I could resonably try the edge version and then, I understand that I have to install armbian-bsp-cli-radxa-zero3-edge linux-u-boot-radxa-zero3-edge linux-headers-edge-rockchip64 Is there more to install ? or less ? And, does I have to remove old (vendor) kernel version before ?

• 0

  Reputation Points

• 3 replies
• 4.5k views
• 1 follower

d83fr

February 12, 20251 yr

Hi, I bought a Rock 5C with the official fan/heatsink: https://radxa.com/products/accessories/heatsink-6540b/ After installing the Armbian server image, I ran these two commands: ```bash ls /sys/class/thermal/cooling_device*/type cat /sys/class/thermal/cooling_device*/type ``` and found that there is no `pwm-fan`. Then I installed the official Radxa Debian image and ran these two commands again. `pwm-fan` exists and I can make it starts spinning by running: ```bash echo 255 | sudo tee /sys/devices/platform/pwm-fan/hwmon/hwmon*/pwm1 ``` Is the fan module supported in Armbian? If yes, ho…

• 0

  Reputation Points

• 3 replies
• 4.5k views

Reguna

January 25, 20251 yr

Hello all, I got a problem after new update of armbian firmware through your own module (script). The left USB port on pinebook pro has stoped working at all. Before that was occasionaly after 6 -7 boot ups only one time not working (it is used for mouse). Now after x rebooting it doesnt work at all. The right USB port works without problems. On the left, also USB flash drive doesn't work. No idea, what could it be? Before, as already said, it has worked in 90%. Before firmware upgrade.

• 0

  Reputation Points

• 6 replies
• 4.5k views

pinebookpro-owner

November 8, 20232 yr

Dear all, I'm running latest Armbian Bionic on Pine64 RockPro64, trying to connect a Midi Keyboard device (having several of them for testing), but it is not recognized by ALSA. If I run acconnect -l After connecting the keyboard, it's not listed (same behavior with different keyboards). Does anyone possibly knows what module might be missing in the kernel? Thanks..

• 0

  Reputation Points

• 7 replies
• 4.5k views

Igor

June 18, 20197 yr

Homeassistant fails to install logs.txt

• 0

  Reputation Points

• 3 replies
• 4.5k views
• 1 follower

Marco Zberg

March 18, 20251 yr

Hi @ all, long time reader, but never managed to register. Now it is time... as I'm not able to solve this myself, kindly asking for help. I'm stuck, my Orangepi 5 plus stops boot at this: Loading, please wait... Starting systemd-udevd version 252.36-1~deb12u1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... (initramfs) What happened before? Last year I bought the Orangepi 5 plus (8GB) and went ahead, testing everything out - having incredible fun with this little box. But with a way to old/slow sd card which finally failed two or three months ago. I went ahead and wrote the A…

• 0

  Reputation Points

• 4 replies
• 4.5k views

Zyxx

April 2, 20251 yr

Is anyone using the current Kodi Flatpak, Omega? I'm having issues viewing videos that have pixel format of yuv420p10le with the current apt repository Kodi Nexus. I thought to try Kodi Flatpak and it worked and I was able to view those yuv420p10le videos without issue. However, it was choppy and had high CPU usage...around 80% on many of the CPUs. I'm trying to figure that out. It's happening on all types of videos. All is played using software decoding. I've never gotten hardware decoding working. In the Kodi Nexus version I'm using it also software decoding but very low CPU usage. In any case, just want to see what experiences …

• 0

  Reputation Points

• 5 replies
• 4.5k views

royk

February 11, 20251 yr

The latest version of RKNPU Driver is 0.9.8, 0.9.7 version doesn't works with rknn-llm or other projects.

• 0

  Reputation Points

• 1 reply
• 4.5k views

Werner

February 16, 20251 yr

I just tried the official Jammy image on the Rock Pi S, which does not boot. Looking at serial, it halts after "Starting kernel ...". I've tried redownloading the image, burning it again and on a different SD card. I also tried the bullseye image, which *does* boot (which makes me believe this is not a hardware issue). Anyone with a Rock Pi S that could confirm my observation? This image failed to boot: Armbian_22.08.7_Rockpi-s_jammy_edge_5.19.16.img Serial output: rock-pi-s-fail.txt This image booted ok: Armbian_22.08.7_Rockpi-s_bullseye_edge_5.19.16.img Serial output: rock-pi-s-ok.txt Diff of serial output (up t…

• 1

  Reputation Points

• 6 replies
• 4.5k views
• 1 follower

Igor

January 11, 20233 yr

Hi guys, I created another device tree overlay that I needed, to enable two user leds on GPIO. Specifically GPIO0_B7 and GPIO0_C0, which is pins 27 and 28 on the header. Posting it here in case someone needs it, like I did with with the SPIdev overlay too. Here it is: rk3308-user-leds.dts What I needed this for is ethernet port LEDs, since the original connector does not include them. To get standard ethernet LED behavior on these newly defined LEDs, you can do this (you need su access): modprobe ledtrig-netdev echo "netdev" > /sys/class/leds/rock-s0\:orange\:user1/trigger echo "netdev" > /sys/class/leds/rock-s0\:green\:user2/trigger e…

• 1

  Reputation Points

• 10 replies
• 4.5k views
• 1 follower

Meestor_X

February 8, 20251 yr

I used sudo swapoff -a as suggested in this thread: but the setting isn't persisted, and upon reboot sudo swapon --summary shows a partition There's no "swap" text in my /etc/fstab I'm trying to install Kubernetes, so I need to disable swap.

• 0

  Reputation Points

• 1 reply
• 4.5k views

trip

April 10, 20206 yr

Hello togehter, i had 2 ASUS TinkerBoard S and I want to work with your software... The Software was via Etcher installed on several MC - Cards (16, 32 and 64 GB), but it still not working. The POWER - LED is red and the both LEDs on GBIC - Interface are blinking green and yellow :-( So, what kind of problems that I have here. I tried out several IMAGE from your WebSite - but no one won't to work with me :-( Best regards Matthias

• 0

  Reputation Points

• 7 replies
• 4.5k views
• 1 follower

MatthiasK

March 24, 20206 yr

Hello Armbian forum, I need to have a GPIO interrupt on Orange PI5. I have successfully installed WiringOP and I am using it with C code. The problem is that the interrupt is not working, and I am receiving the following error. How can I proceed? Does anyone know how to enable the WiringOP interrupt on the GPIO PIN? Code C : #define AUX 13 wiringPiISR(AUX, INT_EDGE_FALLING, &MyFunction); Error: wiringPiISR: unable to open /sys/class/gpio/gpio92/value: No such file or directory PS. I have just successfully installed this version: Armbian 23.02 Jammy Gnome

• 0

  Reputation Points

• 7 replies
• 4.5k views
• 1 follower

elsabz

June 8, 20233 yr

Using Jun 26's Sid_vendor_server-kali, my Zero 3W is stuck in a loop. I can't "Create a loop password" as it'll instantly jump to the "armbian-security login:" prompt. If I login with the default root:1234, I'll briefly see the welcome screen, followed by a very brief "waiting for the system to finish booting", then it's back to 1. This occurs regardless of internet access (provided by a USB-C ethernet adapter, for which Armbian reports a valid LAN IP address).

• 0

  Reputation Points

• 3 replies
• 4.5k views
• 2 followers

laibsch

July 21, 20251 yr

Since I re-installed 23.8 Jammy with the extra ppa:liujianfeng1994 repo - I haven't been able to play any videos on my OPI5. All players I tried seem to have kernel issues decoding any h264. I've narrowed down the error message to a 4Gb memory limit with the selected version of the drivers but I was wondering if anyone had luck with playback. I had better luck with Jammy 23.4 and I regret upgrading. What is the recommendation? Should I try nightly with 6.6.0-rc1 kernel? I assume this one doesn't need panfork drivers anymore or are there other recommendations for h264 playback?

• 1

  Reputation Points

• 9 replies
• 4.5k views
• 1 follower

OttawaHacker

October 12, 20233 yr

Hi all. Is heatsink required for the libre 3328? When I log in to armbiam temp says 60 but it is in red text.

• 0

  Reputation Points

• 4 replies
• 4.5k views

Johnny

November 21, 20187 yr

I installed Armbian 23.11 Bookworm Kernel 6.1, Size: 482Mb, Release date: Nov 30, 2023. After installation, a CH340 based board was connected to my original Tinkerboard and recognized. Subsequently, I used armbian-config to provide the default desktop (Cinnamon flavor). Thereafter, the CH340 board is incompletely recognized. Specifically, no device is presented as /dev/ttyUSB?. The device appears in the list from lsusb, the kernel module ch341.ko loads, but no device in /dev. The forum search shows a previous instance of a similar issue many years back. I attempted to build the driver from wch.cn, but the kernel sources pulled from armbian-config were for the Linux tinker…

• 1

  Reputation Points

• 6 replies
• 4.5k views
• 2 followers

dgw

February 2, 20242 yr

It doesn't detect any wifi network. And when I run iwconfig. wlan0 doesn't appear (only eth0) What can I do?

• 0

  Reputation Points

• 2 replies
• 4.4k views

Tido

August 12, 20179 yr

Hello. I'm sure this has been discussed a lot but I couldn't find anything recent. I just got my Orange Pi 5 Plus and I installed Armbian 23.8 Bookworm CLI on it. It is really fast and I love it so far. I see that it is unclear whether we have some kind of working vulkan drivers or not but I just installed the mesa-vulkan-drivers package and the vulkaninfo command is actually returning output so does that mean that we have vulkan drivers that work for the G610? Thanks in advance

• 0

  Reputation Points

• 1 reply
• 4.4k views
• 1 follower

m33ts4k0z

October 13, 20232 yr

Hi Team, Greetings. I am using OPi4 LTS Emmc with 16 GB version. kernel: Linux orangepi4-lts 5.15.93-rockchip64 #23.02.2 SMP PREEMPT Fri Feb 17 23:48:36 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux. installed Armbian in Emmc worked like charm. Issue: I connected the SSD WD SN570 and format with nand -sata-install on Armbian to boot and use SSD boot. then I got successful msg all done and ready to reboot. once after the reboot I got this msg. then I tried root it doesn’t work and control-d comes back to same screen. Troubleshooting with a gentleman's assistance: 1. Booted wit…

• 0

  Reputation Points

• 5 replies
• 4.4k views
• 1 follower

Smartman

April 28, 20233 yr

Hy, I'm looking for a Command to get the Serial Number of my Tinkerboard. I have found this in the Web : cat /proc/cpuinfo | grep Serial | sed s/.*\ //g But i get 000000000000. Someone have an Idea please? Thank you :)

• 0

  Reputation Points

• 2 replies
• 4.4k views
• 1 follower

domoticity

February 25, 20197 yr

Hi everyone! Someone has implemented support for mcp2515 for tinker board in armbian? Thank you!

• 0

  Reputation Points

• 5 replies
• 4.4k views
• 1 follower

TonyMac32

December 5, 20187 yr

I was able to install an ebay 18650 UPS on my ROC-RK3328-CC, and found out in the instructions that it also has an RTC Module. I would like to utilize that feature, if possible, but I am not entirely sure how to go about it. I have used the armbian-config to enable i2c7, and... that's pretty much as far as I got. Viewing the instructions under "How to setup and check the RTC module:" https://wiki.52pi.com/index.php/UPS_(With_RTC_%26_Coulometer)_For_Raspberry_Pi_SKU:_EP-0118 The instructions call to use modprobe i2c-bcm2835 however, it doesn't appear that my copy of Armbian 20.08.7 Buster has this driver. Is there another way to setup an…

• 0

  Reputation Points

• 2 replies
• 4.4k views

TonyMac32

October 19, 20205 yr

Hello, as already mentioned in topic USB C port doesn't work after upgrading to the latest kernel 6.6.2 . The previous problem with not working left usb 3 port persist no more. Everything is fine. As I remember , before update the usb c port has worked with the adapter and the devices like mouse, usb flash etc. Now it doesn't work any more, furthermore it gives no signal of life. There is 0 amps current measured, also dmesg -W gives no output at all after plugging in the device. PS: I was unable to upload the report file, also the service paste.armbian.com doesn't work at the moment.

• 1

  Reputation Points

• 6 replies
• 4.4k views

pinebookpro-owner

March 4, 20242 yr

Hi Guys, It seems that I can't boot latest Armbian image from SD-card - system always boots into "inintramfs". See the screenshot. SD-card is 100% working (all sectors tested). The image - 25.11.1_noble_6.12.58_gnome_desktop (downloaded from front page of OrangePi5). Checksum is OK. Please note - I've already tested 3 different prorgams for images: USB-imager, Rufus, Win32diskimager. Nothing helped))). I also re-wrote MTD flash (not sata) by "armbian-install" and got nothing (!) I use my main Armbian-server installed on nvme, but I would prefer to run SD-images as well... Unfortunately, as I see, this became very difficult task lately(((. …

• 1

  Reputation Points

• 6 replies
• 4.4k views
• 1 follower

peacepenguin

September 11Sep 11

Was using my Orange Pi 5 and it rebooted on it's own. After that, it continually reboots. Been running fine for months. Tried restarting a few times. Tried swapping SD cards. It looks like the power supply is OK, although I'll try swapping with another. I had just backed up the SD Card too. I'll try re-imaging an SD card, but I'm thinking the SD card may not be the issue. I hooked up my UART and captured output. At the end of each loop, it looks like it's saying "Starting Kernel" and then restarting. Captured output follows. Any ideas, suggestions or comments on what's happening. I'm thinking it's probably a hardware issue. I …

• 0

  Reputation Points

• 5 replies
• 4.4k views
• 1 follower

eselarm

January 5, 20251 yr

hi guys. I need to connect temperature sensor ds18b20 to thinker board on w1 (one wire) how is posible to put on ??

• 0

  Reputation Points

• 1 reply
• 4.4k views

meres5

October 22, 20178 yr

does displayport over usb-c dock work for you? It doesn't for me neither on 5.15 nor on 6.1.

• 0

  Reputation Points

• 4 replies
• 4.4k views
• 1 follower

Werner

December 9, 2025Dec 9

Hi, I am struggling to get the second NIC (1Gbit) to work. The wireless and first NIC (100Mbit) works All NIC's connected I am using Armbian 22.11.0-trunk Bullseye root@rockpi-e:~# ifconfig -a eth0: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 9a:9c:84:a1:77:63 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 41 eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.150.1…

• 0

  Reputation Points

• 5 replies
• 4.4k views
• 1 follower

maigonis

November 24, 20241 yr

Hi everyone, I’m using an ASUS Tinker Board (RK3288, 2 GB, released in 2017). Since this board is quite old and we are now in 2025 I want to run the latest stable Armbian and develop a Python application using I²C, UART, PWM, and GPIO pins. Which Armbian image and kernel branch (current or edge) is the most stable for this board? Are there any specific steps or adjustments needed due to its older hardware? Thanks!

• 1

  Reputation Points

• 2 replies
• 4.4k views
• 4 followers

jock

July 28, 20251 yr

Hi, I'm running Armbian Stretch on a Tinker Board and trying to use a one-wire thermometer. I have this in /boot/armbianEnv.txt: overlays=i2c1 i2c4 spi2 spidev2 uart1 uart2 w1-gpio However, when I boot the board, I see this in dmesg: [Wed May 8 17:38:43 2019] rockchip-pinctrl pinctrl: unable to find group for node w1_pins [Wed May 8 17:38:43 2019] w1-gpio: probe of onewire@0 failed with error -22 Kernel version is Linux tinkerboard 4.19.33-rockchip #5.77 SMP PREEMPT Wed Apr 3 17:06:29 CEST 2019 armv7l GNU/Linux Any ideas? I'm using the rockchip-w1-gpio.dtbo that was installed with the system. Regards, Dianne.

• 1

  Reputation Points

• 3 replies
• 4.4k views

Dianne S.

May 10, 20197 yr

I've adapted a set of patches from Urja Rannikko, which move the HDMI frequencies definition into the DTS file, with some preconfigured rates if none are defined in the DTS. The original patches set is here : https://www.spinics.net/lists/arm-kernel/msg673156.html The big patch I used as a basis is here : https://github.com/urjaman/arch-c201/blob/master/linux-c201/0020-RK3288-HDMI-clock-hacks-combined.patch I included these patches by splitting them again : https://github.com/Miouyouyou/RockMyy/commit/57ff073fffb5678e75959e566704376f6f52ac17 These patches were suggested to me here : https://github.com/Miouyouyou/RockMyy/issues/3 …

• 0

  Reputation Points

• 3 replies
• 4.4k views
• 1 follower

jock

October 11, 20188 yr

Hello everyone, due to a project I'm working with the Friendly Elec Nanopi R4S board for which I've to use the i2c bus to read data from a sensor. Unfortunately I've not been able to access it, since the system does not recognize it. I tried with different configurations using the /boot/armbianEnv.txt file with no results, however the i2c ports are enabled. To rule out functionality problems in the sensor, I connected it to other boards (e.g. nanopi Neo3 using Armbian) without problems. Do you have any idea what could be the cause of this problem? Thanks!

• 0

  Reputation Points

• 1 reply
• 4.4k views

mef1k

October 3, 20224 yr

This https://github.com/Joshua-Riek/ubuntu-rockchip/wiki/Orange-Pi-5 produces nearly 0 dropped frames at 4K 60fps on https://www.youtube.com/watch?v=LXb3EKWsInQ While latest Armbian_23.11.1_Orangepi5_jammy_legacy_5.10.160_gnome-amazingfated_desktop.img.xz and doing immediately after install, only these commands: sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia sudo apt update sudo apt dist-upgrade sudo apt install mali-g610-firmware rockchip-multimedia-config exactly like it says on https://www.armbian.com/orangepi-5/ and sudo reboot produces alot of dropped frames on same youtube …

• 0

  Reputation Points

• 4 replies
• 4.3k views
• 3 followers

BOFFBOY

January 11, 20242 yr

Hello, I'm using Armbian 24.5.3 Bookworm Minimal / IOT but there is no temperature in motd. When I inspect the normal datasources, it symlink to non-existent folder.

• 1

  Reputation Points

• 2 replies
• 4.3k views
• 1 follower

NixiElectra

September 15, 20242 yr

I have Rock Pi S V13, that has 4 UART ports. I'm already connecting to the board via serial console on /dev/ttyS0. How can I find out what are the other ports assignments/paths? I have tried to use a Python script to detect the output by using an FTDI to USB board with no luck (the voltage and baudrate are correct). The Python script taken from manual: import serial import time # I've tried /dev/ttyS2 and /dev/ttyS4 ser = serial.Serial(port='/dev/ttyS4', baudrate=115200, timeout=0.1) print(ser.name) try: while True: ser.write(b'hello') time.sleep(0.5) except KeyboardInterrupt: …

• 0

  Reputation Points

• 0 replies
• 4.3k views

Armate

February 21, 20233 yr

Basically, I'm trying to get iptables to block per country: https://daenney.github.io/2017/01/07/geoip-filtering-iptables.html I got most of things work until getting problem on installing xtables-addons-dmks # apt-get install --reinstall xtables-addons-dkms ------------------------------ Deleting module version: 2.12 completely from the DKMS tree. ------------------------------ Done. Unpacking xtables-addons-dkms (2.12-0.1) over (2.12-0.1) ... Setting up xtables-addons-dkms (2.12-0.1) ... Loading new xtables-addons-2.12 DKMS files... Building for 4.4.174-rk3399 Building initial module for 4.4…

• 0

  Reputation Points

• 2 replies
• 4.3k views
• 1 follower

Jerry Jyrer

March 30, 20197 yr

So a clean install of "Armbian 25.2.1 Noble Gnome" with the vendor kernel (6.1.99) fails to boot when installed on an nvme SSDwith the armbian-install script, when btrfs is chosen as the partition type. I am not sure if the files are copied over correctly, since the ~6GB image on the SD card is copied as 2.9GB on the btrfs partition, but there are no errors occuring as far as I can see. The bootloader is up-to-date, and I can access the btrfs drive when booted from the SD card, so the kernel supports btrfs I guess? However, I think there are some things going "wrong", since the armbianEnv.txt file on the nvme SSD has ext4 instead of btrfs as the ro…

• 1

  Reputation Points

• 6 replies
• 4.3k views

Omer Hasanov

April 3, 20251 yr

I still have a problem configuring the wifi hotspot on the armbian distribution for tinkerboard. The hotspot is clearly unstable. So none of my computers can't connect to it and my phones and tablets have a unstable connection. I thought having found a turnover using a call to iw with a frequency of 1s. This was reactivating the wifi for some times (that should simulate a continuous connection) but it looks that it doesn't work anymore. So I am stuck with that, I am unable to configure a stable hotspot. Is there something to do with the rtl8723 driver, or have I no hope to make it works ?

• 0

  Reputation Points

• 3 replies
• 4.3k views

Igor

January 9, 20188 yr

Some prerequisites. Distro: Debian 12 bookworm, xfce; Board: Orange Pi 4 LTS; Screen: Samsung SyncMaster 923NW, 1440x900_60, VGA. Using hdmi to vga adapter with vga cable. Tried one piece hdmi to vga cable. Tried other all in one adapter that goes in to the screen and goes to hdmi cable. The problem. While running armbian distro screen resolution is set to be 1080p by default. Using xrandr I can not set it to suggested 900p. Every time I set any other resolution - screen turns black until I set it back to 1080p. It is not a hardware issue, because right now I am running headless Debian bullseye from orange pi and the resolution is set …

• 1

  Reputation Points

• 2 replies
• 4.3k views

Guillermo seara

November 5, 2025Nov 5

Hello ! I bought this screen recently: https://www.seeedstudio.com/10-1-inch-1200-1980-HDMI-IPS-LCD-Display-p-2863.html I tried to connect it to my Tinkerboard but could not get an image. On an raspberry I have input specific display settings in the configuration file. hdmi_drive=2 hdmi_mode=87 disable_overscan=1 # 10.1 inch hdmi_timings=1200 0 100 24 52 1920 0 65 4 25 0 0 0 60 0 169000000 0 max_framebuffer_width=1920 max_framebuffer_height=1920 display_rotate=3 framebuffer_width=1920 framebuffer_height=1200 By cons I do not know how to do with the tinkerboard. same problem on Nanopi-M4

• 0

  Reputation Points

• 2 replies
• 4.3k views

Azq2

March 21, 20197 yr

I am using the M.2 connector on the Radxa Rock 5B+ board to connect an LTE module (EM7455). According to the datasheet and engineers, this M.2 slot is connected to the board via a USB hub (USB 2.0). When using the official Radxa OS, I can successfully detect the module under lsusb, the necessary kernel modules load correctly, ModemManager recognizes the modem, and I can establish an internet connection. However, on Armbian, I am experiencing a strange issue. The device does not consistently appear under lsusb; instead, the logs show that it keeps connecting and disconnecting in an endless loop. I am unsure of the root cause and how I can gather more detailed log…

• 1

  Reputation Points

• 3 replies
• 4.3k views

Igor

March 6, 20251 yr

I am interested in hardware video support and wether ffmpeg has hardware support on the RK3588 and Mali G610MC4 GPU. And was wondering if someone whould be interested in giving me the output of a few tests for me please ? ``` ffmpeg -hide_banner -encoders ``` ``` ffmpeg -hide_banner -decoders ``` ``` ffmpeg -hide_banner -hwaccels ``` Many thanks in advance.

• 0

  Reputation Points

• 2 replies
• 4.3k views

AaronNGray

August 30, 20242 yr

I've found information on how to use your own IR remote controller from this site: https://forum.odroid.com/viewtopic.php?f=215&t=44671 In short: 1. Enable logging from the IR kernel module, enter in a terminal: sudo -i echo 1 > /sys/module/rockchip_pwm_remotectl/parameters/code_print dmesg -w 2. Check if your remote is supported by pressing the keys on your remote. It should give you info like: [ 3485.342354] USERCODE=0xfb04 [ 3485.369309] RMC_GETDATA=fd 3. Download the overlay file below and edit the usercode and the code for each key. So for like with the key above it'll be 0xfd 4. Place the header f…

• 0

  Reputation Points

• 0 replies
• 4.3k views
• 2 followers

royk

March 28, 20242 yr

Saw this over on the LKML... some folks might be interested in this one... http://lkml.iu.edu/hypermail/linux/kernel/1901.0/02233.html Changes checked in against staging... staging: video: rockchip: video codec for vendor API staging: video: rockchip: fixup for upstream staging: video: rockchip: add video codec arm64: dts: rockchip: add video codec for rk3399

• 0

  Reputation Points

• 1 reply
• 4.3k views

TonyMac32

January 7, 20197 yr

Hi guys, I would like to make a support request for the: NanoPi-R76S ($49): https://www.friendlyelec.com/index.php?route=product/product&product_id=308 Thank you for considering. Dantes

• 1

  Reputation Points

• 12 replies
• 4.3k views

Dantes

September 11, 20251 yr

Hi all, reporting a regression in new Armbian 24.2.1 kernel version. New kernel is causing Orange Pi 4 LPS not to boot most of the time, when it boots, then there is no network. Kernel hangs with oops errors on the screen, and all debugging stuff. Sorry that I did not caught any of them on my phone, but it would have been incomplete anyway. How to reproduce: Install any 24.2.1 based system on Orange Pi 4 LTS Upon first boot, you will have issues. No Ethernet network. Second boot will most likely not succeed no matter what you do and system will brick permanently, by not booting at all (no video output), or booting and then showing kernel crash. …

• 0

  Reputation Points

• 5 replies
• 4.3k views
• 2 followers

jock

April 5, 20242 yr

I just started RockPro64'ing (though been using Linux for about 25 years) and bought the low profile fan with the RockPro64. Armbian (downloaded today) installed fine, sees my NVME etc. so all good. The only issue I have is that once the OS starts up the fan comes on and never stops - it seems to be running 100% all the time. It the speed meant to vary? And is it meant to turn off sometimes when not required? I'm wondering if I am I missing a config file entry for this. Thanks for any assistance and well done on the distro.

• 0

  Reputation Points

• 3 replies
• 4.3k views
• 2 followers

Indieshack

July 7, 20206 yr

Hi, I was just trying to test locally build image with edge kernel (Armbian_23.11.0-trunk_Orangepi5-plus_bookworm_edge_6.6.0-rc1.img) by flashing it on SD card and then trying to boot off it in my Orange Pi 5+. The board just sits there with the LED blinking and that's it. The legacy kernel image (Armbian_23.11.0-trunk_Orangepi5-plus_bookworm_legacy_5.10.160.img) boots fine. Do I have to carry out some extra step(s) to test the edge kernel? It's not a show-stopper for me as I have legacy image booting of EMMC nicely (and I am running jellyfin in docker happily there). It's just I thought I might test out some bleeding-edge s…

• 0

  Reputation Points

• 5 replies
• 4.3k views

Vijay Gill

March 25, 20242 yr

Tried 5 diferrent microSD cards, 3 card readers, multiple redownloads on Mac and Windows. Diferrent power supplies, including 100W charger and 52pi EP-0136 direct 5v supply. No green LED, no LAN communication, no HDMI output. Everything i get is in log (via UART) Please help... i've got no more ideas. DDR Version V1.08 20220617 LPDDR4X, 2112MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB Manufacturer ID:0x1 Samsung CH0 RX Vref:32.7%, TX Vref:1…

• 0

  Reputation Points

• 5 replies
• 4.3k views
• 1 follower

DimonKyiv

February 19, 20233 yr

Hello, I installed Armbian Hirsute xfce bleeding edge kernel 5.13.y on my RockPro64 4GB and updated it right after that. After restarting after the update, ethernet doesn't work anymore. (Wifi connecting icon is shown and no connection to ethernet) dsmesg says that the link is up. armbianmonitor: https://paste.ubuntu.com/p/9Yz8SJVrzS/ apt/history.log: https://paste.ubuntu.com/p/GQbfZp3Xch/ For apt history only the last two operations seem relevant. I assume the previous ones are made by whoever/whatever created the image.

• 1

  Reputation Points

• 5 replies
• 4.3k views
• 2 followers

ScottP

September 24, 20215 yr

Hi, I have installed "Armbian_22.08.7_Tinkerboard_bullseye_current_5.15.74_minimal.img.xz" on a Tinkerboard (no S, with RK3288). I have tried to set the output of some header pins without success. I used both "sysfs" and "gpiod" (which uses char-devices). Test procedure, e.g. for pin 36 (gpio223): # echo "223" > /sys/class/gpio/export # cat /sys/class/gpio/gpio223/direction in # cat /sys/class/gpio/gpio223/value 0 # echo "out" > /sys/class/gpio/gpio223/direction # cat /sys/class/gpio/gpio223/direction out # echo "1" > /sys/class/gpio/gpio223/value # cat /sys/class/gpio/gpio223/value 0 # echo "0" > /sys/class/gpio/gpio223/value # ca…

• 0

  Reputation Points

• 4 replies
• 4.3k views
• 1 follower

usual user

November 26, 20223 yr

Hi I have a problem with change desktop language from en to polish. I tryed all solutions armbian-config , dpkg-reconfigure locales, export LANG. After reboot I got english desktop and locale info http://ecocut.pl/wp-content/uploads/2019/03/locale-1.jpg

• 0

  Reputation Points

• 4 replies
• 4.3k views

Kisuke-CZE

September 8, 20197 yr

I am running armbian buster Armbian_5.91_Rockpro64_Debian_buster_default_4.4.184_desktop.img. I need rt_preempt in order to run linuxcnc. I started with the 5.0.21.tar.gz kernel source from <https://mirrors.edge.kernel.org/pub/linux/kernel/v5.x/> and the rt_preempt patch 5.0.21-rt16.patch.gz from <https://mirrors.edge.kernel.org/pub/linux/kernel/v5.x/>. I applied the patch to the kernel source and compiled it on a 4gb RockPro64. It boots fine into a remote terminal using ssh but there is no display on my HDMI monitor. The white LED is showing but the red LED is not lit. I had an earlier version of linux-5.0-rt running on armbian stretch so …

• 0

  Reputation Points

• 3 replies
• 4.3k views
• 1 follower

acondit

September 25, 20197 yr

hi，Kind hearted people ubuntu22 gome desktop How to configure the default settings of non-stop screen and non automatic screen lock？？ I tried to execute: sudo systemctl mask sleep.target suspend.target hibernate.target hybrid-sleep.target it can only solve the problem of not entering sleep mode！！！ But the screen will still go black, So how to set the default black screen never??? help ,help

• 0

  Reputation Points

• 5 replies
• 4.2k views
• 2 followers

IBV

May 14, 20251 yr

Hello ! I've bought a Orange Pi 5 PRO board about 2 months ago . I've tryed all images (Linux and Android) from the official Orange Pi site . Later I tryed Armbian . In the end I've concluded that the best choice is Armbian 24.5.2 Noble Gnome ( Armbian_24.5.2_Orangepi5pro_noble_vendor_6.1.43_gnome-oibaf_desktop.img ). Using Armbian 24.5.2 Noble Gnome I got the best (the smoothest) video playback, both in video players and online (youtube) content . And it' s very responsive in operation, generally . I have one single issue : My MCE remote is not detected properly - the Play, Pause, Next, Previous, Forward, Rewind buttons did't perform any actions when …

• 0

  Reputation Points

• 5 replies
• 4.2k views
• 1 follower

Emil Gruia

January 17, 20251 yr