Rockchip

I'm using an Orange Pi 5 Plus 16GB SBC, with Armbian image (https://dl.armbian.com/orangepi5-plus/Bookworm_current_cinnamon-backported-mesa) which uses Kernel 6.12. I am trying to get a BME280 I2C sensor attached to the following pins of the 40 pins; 1 (3.3v), 3 (GPIO0C0), 5 (GPIO0B7), and 6 (GND). The BME280 sensor has the VIN wired to 3.3v (pin 1), SDA wired to SDA (pin 3), SCL wired to SCL (pin 5), and GND to GND (pin 6). The device should use address 0x76, but isn't listed under the four I2C buses found in /dev. This configuration worked fine when using the stock OrangePi 5 Plus Debian Bookworm image, but does not have I2C2 listed as a device under /dev un…

• 0

  Reputation Points

• 9 replies
• 5.8k views
• 1 follower

Robert Pace

December 29, 20241 yr

Before writing I searched the forum a bit but couldn't find any recent posts about it. I have an OPI5 board and on NVME I would like to install armbian. I downloaded the image to micro sd and it boots fine. At this point I don't know what to do because I had to waste a lot of time on it some time ago and I don't remember the steps. With the armbian-config utility is it possible to clone the armbian release I am using on the micro sd? I remember that this wasn't possible some time ago. I would like to know specifically the steps to take and whether it is advisable to delete any old partitions on nvme. Thank you

• 0

  Reputation Points

• 8 replies
• 13.6k views
• 1 follower

Lele

December 29, 20241 yr

This is a new release of the uefi firmware for Orange Pi 5 Plus which now has mainline kernel support. My thought was that this new release would support armbian uefi builds but so far no love. Does anyone know of an armbian build that would work with this??? The is the one of the tag lines from readme.md found @ https://github.com/edk2-porting/edk2-rk3588 "It delivers a PC-like standardized boot experience, supporting multiple operating systems, such as Windows, Linux, BSD and VMware ESXi."

• 0

  Reputation Points

• 2 replies
• 4.7k views

Hooutoo

December 28, 20241 yr

Desktop images with Armbian Linux v6.12 variant Cinnamon with mesa/vpu support fails to boot from SD card. The message displayed on screen is "Begin: Running /scripts/init-premount ... (initramfs) _" SPI was erased, and the minimal install have no issues booting from a sd card. The SBC is an Orange Pi 5 Plus with 16gb ram

• 0

  Reputation Points

• 7 replies
• 7k views
• 1 follower

Robert Pace

December 26, 20241 yr

I have updated my board to run on Armbian 24.11.1 with KDE. I am mainly using it to connect to my remote computer using RustDesk and I am notice that the fps I get is lower than when I was on 24.8.1. There I got around 25-30fps, but on the new version I can get max around 15. Are there any gpu drivers I can try or tests I should run in order to see how well the gpu performs? output from armbianmonitor - https://paste.next.armbian.com/recigaluza

• 0

  Reputation Points

• 3 replies
• 3k views

Egert

December 19, 20241 yr

Hey folks, im trying to compile a realtime kernel for mt orange pi 5. I plan to use it for djing. A fully preemptive kernel delivers better performance for this, as less xruns appear. I am following the official dev instructions and am using the docker method, Compiling only the kernel, not the entire armbian OS. I copied a realtime patch (actually I tried several sub versions of 5.10) from the kernel.org realtime project site into the userpatches directory (I looked up the correct orange pi 5 subfolder name but forgot it rn) but compiling throws me some errors. Has anyone succeeded in creating a kernel like this for the orange pi 5 and/or co…

• 1

  Reputation Points

• 22 replies
• 21.4k views
• 3 followers

Mr.Tree

December 19, 20241 yr

Not an issue nor a bug nor a trouble abour my Orange pi or Armbian. I wanted to build my "own" armbian for educational purpose. I mean to raise my knowledge. I followed this page. https://docs.armbian.com/Developer-Guide_Build-Switches/ however since it's done. I'm looking for about how to make the *.img file or if I can use *.deb located in my ~/build/output/debs I just miss these informations to finish and trying my failure compilation. I say failure compilation because "first time" is always a fail By the way, if I posted in the wrong place. Delete my post and please accept my apologies.

• 0

  Reputation Points

• 1 reply
• 2.3k views
• 1 follower

Werner

December 17, 20241 yr

I have an Armbian installation on the NVMe drive and I'm trying to switch back to boot from SD card. In `armbian-config` I messed up the boot settings by leaving the root fs type unchanged, (SD card is in fat32 but NVMe partition is ext4). Now the board boots into initramfs prompt. Here's what I've already tried based on search and ChatGPT: Mount the NVMe partition to `/mnt` then chroot to it, this did work but the `/boot` partition was not mounted inside of the chroot so I can't fix boot env. I also tried `switch_root` but it's not available in the initramfs prompt. Update `/proc/cmdline` to change the root fs back to the Armbian partition…

• 0

  Reputation Points

• 1 reply
• 6.6k views
• 1 follower

Werner

December 16, 20241 yr

I am trying to install Ambian on to the BananaPi-M7 to eMMC using option 6. there is no option for NVME / M2 SSD. I had a failed install as the uSDCard image was 256GB larger than the eMMC, so it balked. I tried a 128GB uSDCard, followed by a 64GB uSDCard, but got the same error each time even on the 64GB one. I seem to have two partitions on the eMMC, mmcblk0boot0, and mmcblk0boot2 now,. I am not sure if they were on the boards eMMC originally or what the boot sequence for the board is If the Masked ROM tries to boot the uSDCard if present and if that fails it boots the eMMC ? Do I clear mmcblk0 and try again with the 64GB uSDcard ? Or is mm…

• 1

  Reputation Points

• 55 replies
• 25.5k views
• 1 follower

AaronNGray

December 15, 20241 yr

I get the following result when trying to run armbianmonitor -u. Is it broken or am I doing something wrong? Armbian 24.8.3 Bookworm CLI on a Rock-Pi S # armbianmonitor -u Collecting info and sending to paste.armbian.com, wait... /usr/bin/armbianmonitor: line 976: iostat: command not found <!DOCTYPE html> <html lang="en"> <head> <meta charset="utf-8"> <title>Error</title> </head> <body> <pre>Cannot POST /log</pre> </body> </html> Please post the URL in the forum where you've been asked for.

• 0

  Reputation Points

• 2 replies
• 2k views

Meestor_X

December 14, 20241 yr

I have built an Orange Pi 5 Plus systems. I have a 256gb eMMC card which seems to run as speed would expect. Yet when I test the NVMe drive I get slow speeds compared to what is suggested to get. I have seen other people posts that suggest they are getting at least 4gb/s using NVME drives. I have searched for other issues but there is no errors in the logs just can't get the speeds I was expecting. I have the following which suggests at least 5gb/s KINGSTON SNV3S500G I have formatted it using Ext4. root@orangepi5-plus:/boot# hdparm -Tt /dev/nvme0n1 /dev/nvme0n1: Timing cached reads: 2804 MB in 2.00 seconds = 1404.10 M…

• 0

  Reputation Points

• 3 replies
• 2.9k views

ozacas

December 14, 20241 yr

I connected a 49" super wide curved monitor (philips 49b2u5900) to opi5+ through HDMI. I would expect to have the possibility to choose between resolutions of 5120x1440 or 3840x1080. Unfortunately I only get 16:9 resolutions. v24.8.4 for Orange Pi 5 Plus running Armbian Linux 6.1.75-vendor-rk35xx Packages: Ubuntu stable (noble) david@orangepi5-plus:~$ xrandr Screen 0: minimum 16 x 16, current 3840 x 2160, maximum 32767 x 32767 HDMI-1 connected 3840x2160+0+0 (normal left inverted right x axis y axis) 1190mm x 340mm 3840x2160 59.98*+ 2048x1536 59.95 1920x1440 59.97 How can I configure the proper resolution? I as have little e…

• 0

  Reputation Points

• 2 replies
• 2.8k views
• 1 follower

David D.

December 14, 20241 yr

I'm trying to set up a DS3231 hardware clock and the system can't find the hwclock command. I installed the util-linux command as other references suggested, but the command still isn't there. Thank you

• 0

  Reputation Points

• 1 reply
• 3.4k views
• 1 follower

Werner

December 12, 20241 yr

I followed the provided instructions to install Arbmbian on Orange Pi 5 Plus 16GB, so I downloaded the official Ubuntu image from the Orange Pi website, and when it booted, it sudo apt update sudo apt install mtd-utils sudo flash_eraseall /dev/mtd0 The flash operation was finished successfully. Then I turned off, loaded Armbian Ubuntu 24.04 (Noble) (Desktop images with Armbian Linux v6.12) on SD and started the machine. I have a monitor connected to the machine, but there is no output. My router doesn't show any new network device, so I suppose that Armbian doesn't load. It's exactly the same situation when I tried to install Armbian without /dev/mtd0 erasin…

• 0

  Reputation Points

• 0 replies
• 3.4k views

Igor V

December 10, 20241 yr

Debian12 gnome Chromium cannot be opened, interface crashes. help,help

• 0

  Reputation Points

• 6 replies
• 4k views

amazingfate

December 10, 20241 yr

I have Orange Pi 5 Plus that I plan to install in a remote location. To boot Orange Pi, I need to press the physical Power On button. How I can setup the machine to boot automatically once the power is supplied? There is nobody on the remote side to press this button. Or maybe there are other options to boot remotely like WakeOnLAN? Where it can be configured? In orangepi-config?

• 1

  Reputation Points

• 5 replies
• 4.7k views
• 1 follower

Werner

December 9, 20241 yr

Please advise on how to fix this, thanks: Setting up rockchip-multimedia-config (1.0.2+jammy) ... dpkg-query: error: --listfiles needs at least one package name argument Use --help for help about querying packages. dpkg: error processing package rockchip-multimedia-config (--configure): installed rockchip-multimedia-config package post-installation script subprocess returned error exit status 1 Errors were encountered while processing: rockchip-multimedia-config E: Sub-process /usr/bin/dpkg returned an error code (1)

• 0

  Reputation Points

• 6 replies
• 5.1k views
• 1 follower

FierroMarco

December 9, 20241 yr

Are display color profiles not supported? Currently no matter which color profile I choose for display, it does not have any effect. Running on latest release stable release for khadas edge 2

• 0

  Reputation Points

• 2 replies
• 2k views

Egert

December 8, 20241 yr

Hello, I'm using a rock pi e ver 3.0 with armbian 24.8.3: I would like to drive the state of a gpio, that of pin 7 or gpio 100: I'm not an expert and I tried to use the GPIOD libraries for python but I couldn't do anything because I get errors; from the command line through the gpiodetect command it seems to me that the chipset is recognized and I see some lines and the status of the gpios but I cannot change the status of these. Am I going in the right direction? Are there other methods to drive these GPIOs? Thank you in advance.

• 0

  Reputation Points

• 3 replies
• 3.2k views
• 1 follower

Werner

December 6, 20241 yr

Help me out, please. Begginer

• 1

  Reputation Points

• 1 reply
• 3.8k views

Igor

December 4, 20241 yr

Hello everyone, Thank you for stopping buy and reading this thread. I have Orange Pi 4 LTS with the latest Armbian Jammy image (Armbian_23.8.1_Orangepi4-lts_jammy_current_6.1.50). But I also want to mention that I've tried the same thing on the "official" Ubuntu image from OrangePi website and it was the same. I need to decode and show RTSP video stream, h264 encoded. First of all, I've tried gstreamer with v4l2 codecs. I was using v4l2slh264dec from gst_plugins_bad. This is the only hardware codec in gstreamer for my device (at least available by default) and it worked fine until I started encountering a strange bug when my video getting stuck into 0.5-1…

• 0

  Reputation Points

• 5 replies
• 9.7k views
• 2 followers

Dave Jones

December 3, 20241 yr

flashed to m2 mvme, board attempts to boot , then after armbian logo it falls into busybox command prompt (

• 0

  Reputation Points

• 1 reply
• 2.7k views

Igor

November 30, 20241 yr

Hello, currently on Rock5B running Armbian 24, I am not seeing the U-Boot output logs during UART debugging. Where in the source code can I enable this? Thank you.

• 0

  Reputation Points

• 3 replies
• 3.6k views

eselarm

November 29, 20241 yr

Hi, First of all thanks for this awesome product, BananaPi M7 is really great in many ways! Only one last thing appears to be broken on our project, I'm having connection troubles from IoT in 2.4Ghz against BananaPi setup as an AP.I'm using the latest up to date armbian server image $ uname -a Linux bananapim7 6.1.75-vendor-rk35xx #1 SMP Tue Nov 12 08:48:32 UTC 2024 aarch64 aarch64 aarch64 GNU/Linux $ cat /etc/*release # PLEASE DO NOT EDIT THIS FILE BOARD=bananapim7 BOARD_NAME="Banana Pi M7" BOARDFAMILY=rockchip-rk3588 BUILD_REPOSITORY_URL=https://github.com/armbian/build BUILD_REPOSITORY_COMMIT=26d182157 LINUXFAMILY=rk35xx ARCH=arm64 BOOT_SOC=rk3588 IMA…

• 0

  Reputation Points

• 3 replies
• 2.8k views

Armbian42

November 29, 20241 yr

I installed Desktop images with Armbian Linux v6.1 Ubuntu 24.04 (Noble) Gnome (Zero 3W) And out of the box after installation I get the message -bash: fork: retry: Resource temporarily unavailable (I have to work through the com port, because because of this error ssh and the desktop cannot work) I checked the performance of the equipment by installing Debian 11 from Radxa, the equipment works correctly (CPU RAM eMMC). Has anyone encountered this problem?

• 0

  Reputation Points

• 2 replies
• 2.8k views

Lukas Veitas

November 29, 20241 yr

Where were the scripts for the 'update_initramfs' and' mkinitramfs' tools generated? I couldn't find it in the package. Please help me, thank you！

• 0

  Reputation Points

• 2 replies
• 2.2k views

eselarm

November 29, 20241 yr

I downloaded and flashed the three images of Armbian 24.8.1 (Noble GNOME, Ubuntu 22.04 Jammy and Debian 12 Bookworm) on the Banana Pi M7, connected to the computer via serial console. The three images are these: Armbian_24.8.1_Bananapim7_noble_vendor_6.1.75_gnome-kisak_desktop.img Armbian_24.8.1_Bananapim7_jammy_vendor_6.1.75_kde-neon-kisak_desktop.img Armbian_24.8.1_Bananapim7_bookworm_vendor_6.1.75_cinnamon-backported-mesa_desktop.img For each image, I booted and logged the board output. The board fails to successfully boot and instead gets stuck in a boot loop. I then mounted the armbi_root partition and edited the file armb…

• 1

  Reputation Points

• 7 replies
• 15.4k views
• 1 follower

armsom-jackson

November 29, 20241 yr

I have to try to run home Assistant on the Radxa Rock S0 and I found the image file on https://www.armbian.com/radxa-rock-s0/ under the Dedicated applications images with Armbian Linux v6.6. I burn the image on the SD card butt that is all I could do, I'm not able to access the Rock S0 any way so I can't say that is working or not. Try to use the Putty with COM port but there's no COM port available, neither I can get any IP address so that I would access it trough Putty or locally trough LAN localhost:8123 I would be glad if someone can point me to the author of the image, I try to look on GitHub but couldn't find any Repository. Any help would be appre…

• 0

  Reputation Points

• 3 replies
• 2.7k views

Igor Qubino

November 29, 20241 yr

hello! Can help me about orange 3b, I want to adapt one dts file to my board, how to correctly indicate the names of the pins, the example gives the following sample entry: https://mjmwired.net/kernel/Documentation/devicetree/bindings/display/panel/sitronix,st7701.txt reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ how to correctly fix this for my board?

• 0

  Reputation Points

• 5 replies
• 3.7k views
• 1 follower

maximilian fletkar

November 28, 20241 yr

ubuntu22 Chrome://gpu The display report is soft processed!!!! How to configure it as hard processing？？？ help thank you.

• 0

  Reputation Points

• 4 replies
• 2.3k views

Igor

November 27, 20241 yr

Couldn't booti from NVME with armbian-config or armbian-install, finally I could do it, a dirty easy and convoluted following way. No details about burning stuff This is what I did 1) boot system from fresh downloaded SD (Armbian Jammy Desktop) 2) NVME setup (sudo gparted) - if empty create a partition table (GPT) if not delete all partitions - create 256MB FAT16 partition (nvme0n1p1) - create EXT4 partition (nvme0n1p2) - optionally create more partitions (system recovery, backups ...) - format partitions nvme0n1p1 -> FAT16 - format partitions nvme0n1p2 -> EXT4 - check partitions (if old N…

• 1

  Reputation Points

• 43 replies
• 31.6k views
• 2 followers

Werner

November 27, 20241 yr

Hi there, I pourchased OPi5 (not preferred OPi5 Pro, because of Armbian lacking support), flashed Debian 24.8.1_bookworm_6.10.6_cinnamon_backported_mesa_desktop, configured (user, switch to static IP, user). Worked OK. Now, ssh'ing into showed "113 packages upgrade". Did "apt upgrade". Download OK, but when applying apgrade process hung twice: - once on "configuring libc", had to power off, then restarted (after an apt-get suggested in response to apt upgrade). Upgrade hung second time (no progress on bottom bar for hours, no new ssh session). - twice was on "configuring udev". After this, board is almost dead: - boots to anima…

• 0

  Reputation Points

• 11 replies
• 4k views
• 1 follower

laurentppol

November 27, 20241 yr

I just upgraded to Arabian 24.5.1 using `apt-get upgrade` and now I cannot load ip_tables: # modprobe ip_tables modprobe: ERROR: could not insert 'ip_tables': Exec format error I’m not sure what to make of it.

• 0

  Reputation Points

• 7 replies
• 5.4k views
• 1 follower

Koehn

November 26, 20241 yr

ubuntu22 gnome desktop Hi, may I ask how to install Google Chrome

• 0

  Reputation Points

• 1 reply
• 4.7k views

Igor

November 26, 20241 yr

Hello OPI5 users. Running Joshua Riek's Ubuntu distro, I keep getting stability issues. Perhaps because I keep using Xorg. Perhaps because hardware acceleration is buggy. In the past I used super stable Armbian OPI5 distro's without hardware acceleration. Infact I still use Armbian on another RK3588 box, I don't think it has EVER crashed, running docker, Mosquito, HomeAssistant, and a buch of other things. Now that my Orange Pi 5 gets a slightly more serious use as webserver, I really like to get rid of the unpredictable Xorg crashes, and gladly would sacrifice HW acceleration for stability. My situation is this: Using JR Ubuntu Because I …

• 0

  Reputation Points

• 4 replies
• 8.8k views

Bas

November 25, 20241 yr

Hello, my development board is Rock5B, and I am using the Armbian system for a recent project. I have already compiled the firmware in the armbian/build/ directory, and the device starts up normally. I want to modify and customize my U-Boot and kernel. After compiling Armbian, I would like to recompile U-Boot or the kernel in the armbian/build/cache/sources directory. Are there any commands to rebuild U-Boot and the kernel?

• 0

  Reputation Points

• 2 replies
• 3.4k views
• 1 follower

lyh

November 25, 20241 yr

Hi, I am struggling to get the second NIC (1Gbit) to work. The wireless and first NIC (100Mbit) works All NIC's connected I am using Armbian 22.11.0-trunk Bullseye root@rockpi-e:~# ifconfig -a eth0: flags=4098<BROADCAST,MULTICAST> mtu 1500 ether 9a:9c:84:a1:77:63 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 41 eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.150.1…

• 0

  Reputation Points

• 5 replies
• 4.4k views
• 1 follower

maigonis

November 24, 20241 yr

Hi there, my new OPi5 with Armbian Bookworm Cinnamon mesa backoprted does not see my mPCIe SSD disk. Just got this: https://allegro.pl/oferta/nowy-superszybki-dysk-ssd-512gb-m-2-nvme-2242-9605598735 \ module, but it is not recognized by the system. Armbianmonitor output: https://paste.armbian.com/huhedogene lspci -v output: 0004:40:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0, IRQ 89 Bus: primary=40, secondary=41, subordinate=41, sec-latency=0 I/O behind bridge: [disabled] [16-bit] Memory behind bridge: [disabl…

• 1

  Reputation Points

• 21 replies
• 9.2k views
• 1 follower

laurentppol

November 24, 20241 yr

Hello I encounter a problem when I run the TCPDUMP command Here is the error eth0: SIOCETHTOOL(ETHTOOL_GLINK) ioctl failed: Device or resource busy Work like a charm with Radxa Debian OS, but on two Armbian same problem. Someone knows why ? Thanks

• 0

  Reputation Points

• 6 replies
• 3.8k views
• 1 follower

Neooostef

November 24, 20241 yr

Hi guys, Would someone point me to where to get a particular distro, mainly looking for jammy_legacy_gnome-amazingfated_desktop for OPi 5 Pro ? I have jammy_legacy_5.10.160_gnome-amazingfated_desktop for Pi5 and Pi5 Plus but it does not work on the Pro version. thank you in advance.

• 0

  Reputation Points

• 1 reply
• 2.1k views
• 1 follower

Werner

November 22, 20241 yr

Hello, I noticed that the system has created a swap partition by default. So, Where does the system default to creating swap exchange partitions??

• 0

  Reputation Points

• 3 replies
• 2.4k views

lay

November 22, 20241 yr

I am trying to boot my Rock 5C Lite from an NVME drive, but have experienced some problems with the vendor kernel. I followed instructions by amazingfate in this forum to create a small SD card with a u-boot image, ie I created a complete Armbian image (vendor kernel) on an SD card too boot up the Rock 5c Lite A second, small capacity SD card was inserted into the USB port using a USB adapter U-boot was transferred from /usr/lib/linux-u-boot-*/ to the small SD card: dd if=./idbloader.img of=/dev/sda seek=64 conv=notrunc status=progress dd if=./u-boot.itb of=/dev/sda seek=16384 conv=notrunc status=progress …

• 1

  Reputation Points

• 2 replies
• 5.4k views

north1

November 20, 20241 yr

Hi there, I wanted to know if anyone know if there are any power limits from the SATA power ports, the question is can you power 1 or more 3.5" NAS disks at the same time? Or as a precaution, I take power from the PSU? Thanks, Dany

• 1

  Reputation Points

• 3 replies
• 3.5k views
• 2 followers

ozacas

November 19, 20241 yr

Login, type "sudo armbianmonitor -u" and copy the URL here. the command failed with the following error : /usr/bin/armbianmonitor: ligne 976: iostat : commande introuvable img used : Armbian_24.8.4_Rock-5c_bookworm_vendor_6.1.75-omv_minimal.img.xz hardware : https://docs.radxa.com/en/accessories/penta-sata-hat https://docs.radxa.com/en/rock5/rock5c 4 ssd samasung evo 870 The image works perfectly when flashed on a SD card and booting from the SD card, the Radxa pentaHat works, the disk are powered (green led for the hat, blue led per each disk). However, when the image is flashed on emmc, the OS boot normaly but the pentaHat does…

• 1

  Reputation Points

• 10 replies
• 8.4k views
• 1 follower

royk

November 17, 20241 yr

How can I recover from this? I haven't rebooted: _ _ _ /_\ _ _ _ __ | |__(_)__ _ _ _ / _ \| '_| ' \| '_ \ / _` | ' \ /_/ \_\_| |_|_|_|_.__/_\__,_|_||_| v24.8.4 for Orange Pi 5 running Armbian Linux 6.10.6-current-rockchip-rk3588 Packages: Debian stable (bookworm) IP addresses: (LAN) 192.168.1.2 10.8.0.1 (WAN) xxx.xxx.xxx.xxx Performance: Load: 1% Up time: 21 days 23:00 Memory usage: 10% of 15.35G CPU temp: 41°C Usage of /: 21% of 233G Tips: Support our work and become a sponsor https://github.com/sponsors/armbian Commands: System config : sudo armbian-config System…

• 0

  Reputation Points

• 6 replies
• 9.9k views
• 2 followers

ScottP

November 16, 20241 yr

hi After recent sudo apt update && sudo apt upgrade via armbian debian bookwork XFCE chromium and firefox breaks its not updates for chromium or firefox as happens when i hold those packages from upgrading too also on fresh sdcard flash/install without full upgrade(just upgrading chromium and its dependencies via depository) chromium still works fine, its something else in the depository that breaks it

• 0

  Reputation Points

• 3 replies
• 2.7k views
• 1 follower

Werner

November 16, 20241 yr

Hello, Recently I have upgraded Armbian on my PBP (w/o kernel). My current kernel is 5.10.60 #21.08.1. I know, it's old but the newer only makes PBP unusable at all - black screen on boot. My current issue concerns the PBP keyboard. Some keys started generating weird outputs. I have never faced with something like that. When I press 'q' - output is - aq2468 x - zxetuj c - cfghk d - DWRI 1 - the screen is dimming I have no idea if this is software or hardware issue. The computer was on the shelf. Nothing has happened to it physically. After years of fighting with this crap :( - I want to be sure if that is the last straw to put this com…

• 0

  Reputation Points

• 0 replies
• 2.4k views

bushw

November 15, 20241 yr

Hello, the latest armbian image (Bookworm_current_xfce) with kernel 6.6 has issues with the winstar tftp 5 inch hdmi display that I am using. Bootloader (u-boot) is showing but after loading the kernel message, screen goes blank. The screen resolution is 800x480, in attach the pdf specs. Info: the official asus image with kernel 4.4 works, but it is not an option for me as I don't want to use debian buster. Please help. Thank you very much. Bogdan WF50FSYFGDHNV.pdf

• 0

  Reputation Points

• 13 replies
• 7.3k views
• 2 followers

jock

November 14, 20241 yr

I run a audio loop code on a Raspberry pi 4/5 and Orange Pi 5. The latency of audio loop is 0.2 seconds on Raspberry pi but on orange pi it takes 1.2 seconds. For orange pi, i am facing this problem with different Operating systems as well apart from armbian. I've used Ubuntu, Orange Pi OS, Armbian. All have got this problem. The code I have attached. Since the issue is faced in multiple Operating System I strongly feel this has to do with the driver level softwares or directly related optimization from Rockchip. Can anyone guide what I could do audio-loop.cpp

• 0

  Reputation Points

• 1 reply
• 2.7k views

royk

November 14, 20241 yr

Hey guys, we are facing an issue we can not resolve ourselves so we are looking for some help on here... Our Rock Pi E does not restart successfully occasionally. Running the Rock Pi E with latest official Armbian with a USB soundcard attached. We are capturing audio and distribute the captured audio via "(c)VLC" via network. Since a few months we are facing reboot issues which are persistent but not easily reproducible. Whenever we reboot manually, everything works fine. When rebooting via cron it does often not reboot and get into a freeze state which makes it impossible to connect via SSH nor serial-adapter. We already tried switching the power so…

• 1

  Reputation Points

• 2 replies
• 3.1k views
• 2 followers

FabulousGee

November 12, 20241 yr

I'm using ffmpeg and Kodi from the @amazingfate ppa. All has been running great although I don't think that I'm using hardware acceleration. I'm still on an older Jammy with the old/legacy kernel. I've tried newer kernels but getting issues so I stuck with the older kernel. I've started noticing lately that videos are being encoded with pixel format yuv420p10le. In Kodi, I was getting black screens while the audio was playing. I was following up on the Kodi forums, and was told that Kodi needed to be compiled for OpenGL instead of OpenGLES to make the video render properly. This is the thread: https://forum.kodi.tv/showthread.php?tid=379167 …

• 0

  Reputation Points

• 1 reply
• 2.6k views

amazingfate

November 11, 20241 yr

Hi, I do not konow, it this is the right place to raise this ticket. But in stable releases of Armbian it works fine, but there is no video acceleration. I have tried Kodi on Armbian Noble Gnome + trunk MESA/VPU: Armbian_24.8.0-trunk.85_Rock-5b_noble_vendor_6.1.43_gnome-oibaf_desktop.img Kodi falling when I'm trying to install some of extensions. For example https://repo.sc2.zone/ Crash log in the attachment. System log: 2024-06-05T12:01:28.534687+02:00 rock-5b kodi.desktop[3739]: Fatal Python error: PyImport_AppendInittab: PyImport_AppendInittab() may not be called after Py_Initialize() 2024-06-05T12:01:28.…

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

ozacas

November 10, 20241 yr

I have created a micro desktop case. It's an open design that is still in the creation phase. The shell is 3d printed, the sides are acrylic, and the opi5 mount panel can be 3d printed or made from acrylic. I'm looking for feedback with design suggestions/needs. This is the first real opi5 micro tower design currently for OPI5. My cad drawing of the OPI5 mainboard is 99.9% accurate, so if someone wants to use that as a footprint for other projects by all means. https://github.com/berin-aquaquad/orange-pi-5 I am using DesignSpark Mechanical a free cad software that is on par with Fusion360. The shell has been designed as a split body so smaller 3d printers can c…

• 1

  Reputation Points

• 63 replies
• 30.8k views
• 3 followers

berin

November 8, 20241 yr

I want to install jellyfin as a docker container on my Orange pi 5. How can I enable hardware acceleration for it? On the container page (https://hub.docker.com/r/linuxserver/jellyfin) there are instructions for various options, but orange pi 5 is not there of course. I have enabled 3D acceleration as mentioned on the armbian page for orange pi 5.

• 1

  Reputation Points

• 27 replies
• 31.6k views
• 5 followers

obiwantoby

November 7, 20241 yr

I have 2 5C Lite boards a 2Gb and 4Gb version, neither have HDMI output with any stock images either from armbian or radxa. Thru desperation I found an Android image that booted and had screen output, so the HDMI works atleast. After stuffing around I found that the u-boot image extracted from the Rock-5D t2(rsdk) and injected into Rock-5C b1(rsdk) Bookworm_kde image boots and has working screen. Longer story short, getting Armbian 24.11 to work... Narrowed it down from replacing the entire u-boot.itb, I can get a working desktop with kernel version 5.10 Bookworm by removing the rng@fe378000 trngvl section (enabled mali400/bifrost driver in ke…

• 0

  Reputation Points

• 0 replies
• 2.8k views

Jared

November 2, 20241 yr

Hopefully this is not a stupid question but I came across Joshua-Riek/ubuntu-rockchip: Ubuntu for Rockchip RK35XX Devices (github.com) when searching for my video playback issues. Does anyone know how this compares with the current armbian release with vendor kernel? Are all the fixes from that release integrated in armbian or does it go the other way?

• 1

  Reputation Points

• 15 replies
• 19.7k views
• 1 follower

going

November 1, 20241 yr

I have set up Armbian 24.8.4 bookworm on my 32GB Orange Pi 5 Plus. Most everything works as expected out of the box. The second HDMI port doesn't detect the second screen, and the screen displays No Signal. I have tested the cables and monitors to ensure they are functioning. I have also ensured I wasn't plugged into the HDMI input by accident. I was about ready to proclaim it a hardware issue, but on booting the "Official" Orange PiOS Arch image, the dual monitor support worked as expected. I checked the dtb file included with the Arch image, and it has many references to HDMI0 and HDMI1 devices, while the one used by default with the Armbian ima…

• 0

  Reputation Points

• 5 replies
• 5.7k views
• 1 follower

royk

October 27, 20241 yr

Hi, last night a set of updates was installed and I rebooted the Orange Pi 5+ this morning. After the reboot I've seem to have lost the connection to the Orange Pi 5+, it is normally connected without a screen so I access it through SSH and the Open Media Vault web GUI. I've tried to connect it to a screen and then it seems to boot up just fine. Looking around with the screen connected it seems like the network cards aren't detected. My Linux skills are very limited but "sudo lshw -class network" shows nothing. One detail is that my router seems to detect it when it's connected and gives it the normal IP address that I've set in the 192.168.0.x ran…

• 1

  Reputation Points

• 20 replies
• 271.8k views

Joel

October 26, 20241 yr

VERSION=24.8.4 REVISION=24.8.4 Problems: No display. (access only via SSH) CIFS mounts fail Lots of dmesg messages similar to: ... [ 6.421534] rtk_btusb: disagrees about version of symbol module_layout ... [ 6.504179] uio: disagrees about version of symbol module_layout ... [ 376.377046] ipv6: disagrees about version of symbol module_layout ... [ 379.869911] cifs_md4: disagrees about version of symbol module_layout ... Is this problem known about?

• 1

  Reputation Points

• 3 replies
• 3.1k views
• 1 follower

robnielsen

October 24, 20241 yr

Degin: MounlAng root Tile syslel ... Degan: munning escrapusr cucad-lop ... uonc. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. done. Geve up waiting for root file system device. Cowmon problems: ⁃ Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Missing modules (cat /proc/modules; ls /dev) ALERT! UUID=db80a2ac-ec37-4fda-91db-92604becfcce does not exist. Dropping to a shell! BusyBox v1.30.1 (Ubuntu 1:1.30.1-7ubuntu3.1) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) …

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

TheFlash

October 23, 20241 yr

Hello! Iv'e just done a test run installing Armbian for booting off my new m.2 nvme drive. As 'm planning to have the drives 2nd large partition as my basic home file server I'm wondering if I can as easily re-install the OS if/when I need to update it to a newer one? Because the instructions I followed and that I see around do a very basic cat /dev/mmcblk1 > /dev/nvme0n1 onto the raw un-partitioned nvme. My case will be that I have data on a partition on that drive that needs to stay. Is this going to be an issue or are there ways to re-install Armbian or even other distro on the boot partition? Cheers!

• 0

  Reputation Points

• 2 replies
• 3.5k views

Fredrik

October 22, 20241 yr

please, helpme with thist message in boot :

• 0

  Reputation Points

• 11 replies
• 7.8k views
• 2 followers

haajee

October 21, 20241 yr

Hello all, I have noticed that whenever I reboot my Orange Pi 5 board, all the 8 cpus slow down to 408 Mhz with no range, as stated by cpufreq-info: I have created a cronjob script in order to bring the frequency back to acceptable range. I don't even know if this is the correct way to solve this, but I am running the following: echo performance | sudo tee /sys/devices/platform/dmc/devfreq/dmc/governor cpufreq-set -c 0 -u 1800000 cpufreq-set -c 4 -u 2260000 cpufreq-set -c 6 -u 2300000 cpufreq-set -c 0 -g schedutil cpufreq-set -c 4 -g schedutil cpufreq-set -c 6 -g schedutil However, even though I set the frequency for processo…

• 0

  Reputation Points

• 2 replies
• 2.8k views

pdieguez

October 20, 20241 yr

Hi! I'm using Tinkerboard S R2.0 in headless mode, but with LightDM (kiosk mode). It's connected to HDMI display, and I soldered display's backlight on/off contact to a relay that can turn on/off the backlight. I see that Amrbian turns off image output (launches screensaver as a black screen) after 10-15 min, but I could not find out where those settings are stored. Please help to find out.

• 0

  Reputation Points

• 0 replies
• 1.7k views
• 1 follower

SuperMaximus

October 19, 20241 yr

Folks, I've got an Orange pi 5 plus up and running using Armbian, I've used the minimal install and although it's been plain sailing for the main part, no matter what I do I can't work out how to give it a static IP address (dynamic works fine). I've spent an hour trying: armbian-config, - Network | IP | Static and setting it to what I want - it ignores it and when I go back in it's gone back to 127.0.0.1 This page: https://docs.armbian.com/User-Guide_Networking/ Creates the yaml file with my interface abd required address as here: GNU nano 7.2 /etc/netplan/20-static-ip.ya…

• 0

  Reputation Points

• 2 replies
• 10.2k views

DiBosco

October 18, 20241 yr

Someone asked in a different thread how I got Dolphin to run so thought I'd start a thread so not to pollute the other one. Basically it wasn't that hard especially if youve done some git'hubbing before. I think I followed the 'Ubuntu' instructions here. Make sure you get the dependencies and do all the steps correctly. It should build without problems if you do. (remember you have a lot of cores on Opi5 so can use 'make -j6' or even higher) https://github.com/dolphin-emu/dolphin/wiki/Building-for-Linux You then want to set a config flag to make Dolphin use GLES instead of big brother OpenGL. (you probably wa…

• 0

  Reputation Points

• 8 replies
• 13.2k views

Fredrik

October 17, 20241 yr

Hi all , Just installed last supported version: Armbian 24.8.1 Noble Gnome, MESA / VPU, Kernel: 6.1.75, Size: 1.5 GB, Release date: Aug 26, 2024 I have 2 dell monitors : u2515h ultrasharp 1440p, and more modern P3424WE with 3440x1440 max resolution. With both - armbian max resolution in display settings is always 1920x1080. My previous experience here was with radxa zero D1 and 1440p was working here smoothly out of box on different armbian images. I also tried Ubuntu 22.04 (Jammy)KDE NeonMESA / VPU https://dl.armbian.com/orangepi5-plus/Jammy_current_kde-neon-kisak with same results: no resolution higher then 1080p …

• 0

  Reputation Points

• 9 replies
• 7.4k views
• 1 follower

bolet75

October 17, 20241 yr

Hi, How do enable I2C on pins 3,5 of the GPIO header? I need to enable I2C7_M3. How to enable spidev.0 on SPI0_M2? All these overlays are missing... Thank you, Errol

• 0

  Reputation Points

• 5 replies
• 3.8k views
• 1 follower

Werner

October 16, 20241 yr

Hi everyone, I just received an "orange pi 5 plus" and I wanted to use the hdmi-input feature in it. I installed armbian and added the hdmirx overlay, and now I can use ffmpeg or gstreamer to stream video input. Good. Alas, I see no alsa hdmi input card. I tried to search for some settings but didn't find any... The only information I found on this feature are here https://github.com/armbian/linux-rockchip/blob/rk-6.1-rkr3/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts do you have any pointer to give me on how to enable this feature? (I know how to compile stuff, using Linux since 1998 ) thanks …

• 1

  Reputation Points

• 7 replies
• 12.3k views
• 1 follower

ozacas

October 16, 20241 yr

when I switch to static IP, there is no a connection to default gateway. but when using DHCP everything works fine. $ ip route default via 192.168.88.1 dev end1 proto static metric 100 169.254.0.0/16 dev end1 scope link metric 1000 192.168.88.0/24 dev end1 proto kernel scope link src 192.168.88.32 metric 100 $ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 2: end1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 …

• 0

  Reputation Points

• 1 reply
• 2.1k views

0xf1

October 15, 20241 yr

Hi! When I try to access PWM via procedure described here https://tinker-board.asus.com/forum/index.php?/topic/15132-direct-gpio-access/ I see that & are not present (although they should be) I can see pwmchip0, but I don't understand what GPIO it is. Following ASUS docs from GitHub https://github.com/TinkerBoard/TinkerBoard/wiki/User-Guide#gpio-config-table-for-tinker-board-s--tinker-board-s-r20 GPIO32 and GPIO33 should be here: PWM:/sys/class/pwm/pwmchip3 and PWM:/sys/class/pwm/pwmchip2 But those directories are not present. root@tinkerboard:~# ls -la /sys/class/pwm/ total 0 drwxr-x…

• 0

  Reputation Points

• 6 replies
• 4.1k views
• 2 followers

jock

October 14, 20241 yr

How to modify the device name of a wireless network card? wlan0-> custom Gnome ubuntu22.04 help....

• 0

  Reputation Points

• 1 reply
• 1.9k views

Werner

October 13, 20241 yr

Installing: /home/john/Armbian/development_armbian/build/output/debs/extra/jammy-utils/base-files_24.8.0-trunk-12ubuntu4.7-jammy_arm64__1-jammy-1armbian1-Baa17-U12ubuntu4.7-R55fa.deb [ base-files_24.8.0-trunk-12ubuntu4.7-jammy_arm64__1-jammy-1armbian1-Baa17-U12ubuntu4.7-R55fa.deb ] [🔨] '/home/john/Armbian/development_armbian/build/output/debs/extra/jammy-utils/base-files_24.8.0-trunk-12ubuntu4.7-jammy_arm64__1-jammy-1armbian1-Baa17-U12ubuntu4.7-R55fa.deb' -> '/home/john/Armbian/development_armbian/build/.tmp/rootfs-94f20e65-72ab-4c9f-aa58-4f9ea3a1974d/root/base-files_24.8.0-trunk-12ubuntu4.7-jammy_arm64__1-jammy-1armbian1-Baa17-U12ubuntu4.7-R55fa.deb' [🔨] E: Pa…

• 0

  Reputation Points

• 5 replies
• 3.2k views
• 1 follower

lay

October 13, 20241 yr

Hi, A UEFI-ARM64 install of armbian opi5+ 24.11.0-trunk fails during armbian-install due to incorrect knowledge of partitions: root@uefi-arm64:/usr/sbin# lsblk -l NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 1 14.4G 0 disk sda1 8:1 1 256M 0 part /boot/efi sda2 8:2 1 14.2G 0 part /var/log.hdd / zram0 252:0 0 7.7G 0 disk [SWAP] zram1 252:1 0 50M 0 disk /var/log zram2 252:2 0 0B 0 disk nvme0n1 259:0 0 953.9G 0 disk nvme0n1p2 259:3 0 953.6G 0 part /mnt/armbian-install.NQULbp/rootfs /mnt/tmp…

• 1

  Reputation Points

• 21 replies
• 6.9k views

ozacas

October 12, 20241 yr

Hi, After bleeding edge 6.8 or so, I lost HDMI output. Does anyone run the recent kernels with HDMI? Which ? The 6.1.75 kernel has HDMI, but a lacks Mt7961 wifi, and changing keyboard does not work, which probably is my lack of understanding of wayland. Gullik PS the HDMI issue might be a resolution thing, unfortunately I use an old TV ( 1920x1024)

• 0

  Reputation Points

• 4 replies
• 3.5k views

jyce

October 11, 20242 yr

I have a couple Orange Pi's, and the HDMI is broken. I noticed that many believe that it is Armbian, but it is not. Orange Pi's probably won't be where we want them until 2025. I found a couple notes from development teams, one below and one from September. Both say the same thing: essentially it's in the works: "The RK3588 SoC family integrates the newer Synopsys DesignWare HDMI 2.1 Quad-Pixel (QP) TX controller IP and a HDMI/eDP TX Combo PHY based on a Samsung IP block. Add just the basic support for now, i.e. RGB output up to 4K@60Hz, without audio, CEC or any of the HDMI 2.1 specific features." https://patchwork.kernel.org/project/linux-rockchip/pa…

• 0

  Reputation Points

• 1 reply
• 3.7k views

ozacas

October 10, 20242 yr

Hello I have this display http://www.lcdwiki.com/4inch_HDMI_Display-C and touchscreen doesn't work. I write dts file but apparently he is not a privelege and the touchscreen did not work. Can point out my mistakes when writing dts? rockchip-ads7846.dts

• 0

  Reputation Points

• 1 reply
• 2.9k views

robertoj

October 8, 20242 yr

I have the latest armbian 6.1.75-vendor-rk35xx (ubuntu with gnome desktop) installed and everything works perfectly except that some videos are hanging in chromium. In dmesg I get [23230.260311] [drm:rockchip_vop2_mod_supported] *ERROR* Esmart0-win0 unsupported format modifier 0x800000000000351 and then boom, the whole thing stops playing and hangs. No other error anywhere. This happens with specific mp4 videos on specific frames. Any suggestions?

• 0

  Reputation Points

• 1 reply
• 2k views
• 1 follower

ArmBoy1988

October 7, 20242 yr

I have a nice video acceleration on chromium and Ubuntu noble, but not with a video player. Maybe someone can say one and how to install.

• 0

  Reputation Points

• 1 reply
• 2.2k views

maka

October 6, 20242 yr

Good afternoon everyone. Please help me with my problem. I have a Radha board zero 3w and I use the Armbian distrib. 24.8.1 . Everything works fine, except that I can't activate SPI. In the Armbian-config menu there is no hardware section (I tried different flash cards and Armbian versions, the problem persists), I also tried to edit the armbianEnv.txt and add overlays there, but I also did not have success. Tell me what else I can try. Activation works on the native distribution radxa debian.

• 0

  Reputation Points

• 13 replies
• 12.5k views
• 1 follower

maximilian fletkar

October 2, 20242 yr

I just testet all available stable armbian images with radxa zero 3e. when i turn off the machine with shutdown -h 0 or poweroff the system shuts down successfully but the power of the dc dc is not turned off. the 3.3V is still available. i dont know if its only a configuration mistake or a bug. normaly after a kernel shutdown, the driver for rk817 should send i2c package to reset the 817. after that you need a power cycle to recover and restart. https://paste.armbian.com/inibopomew br manuel

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Pulsares GmbH

October 2, 20242 yr

Hello, I would like to have dual boot with a startup menu similar to GRUB on a PC, the idea is to have Android installed on the eMMC and Ubuntu on the NVMe, I am referring to an Orange Pi 5 Plus. Has anyone gotten it or is working on it? Thank you

• 0

  Reputation Points

• 1 reply
• 3.6k views

ozacas

October 1, 20242 yr

Is it possible to switch on H264 encoding HW acceleration in chromium browser for WebRTC? I need to send two 2560x720 streams to server from radxa 5c Thanks

• 0

  Reputation Points

• 0 replies
• 1.9k views

Vass

September 26, 20242 yr

Hello everyone, I’m using a Radxa Zero 3E with Armbian 24.8.1 Bookworm OS and trying to connect a device to Radxa via UART. However, I can’t seem to find the ttyAML0 interface. The only UART interfaces visible are ttyS1 and ttyFIQ0 , but neither works for my setup. I have connected the device to the UART_AO_A pins (pins 8 and 10). Additionally, when I go to armbian-config -> System -> Hardware, no hardware appears on the screen. Could this issue be related to the Armbian image I am using? I’ve already tried the b6 image, but it has a boot problem. I also noticed that the other official Radxa images are marked as pre-release. …

• 0

  Reputation Points

• 1 reply
• 2.5k views
• 1 follower

Werner

September 19, 20242 yr

Hi! I am looking into OdroidM1 network performance with kernel 6.6.47-current-rockchip64 ( 24.8.1 ) For some reason network performance is x10 faster (upstream) in bookworm and noble, when compared to jammy. Downstream performance is fine, delivering the same performance in jammy and the other distributions. Since all of them are using the same kernel, I assume that there must be some configuration that jammy is missing, or? Any idea about what could be going on?

• 1

  Reputation Points

• 12 replies
• 5.3k views
• 2 followers

rvalle

September 18, 20242 yr

After booting up armbian 23.02.2 on my orange pi 4 LTS, cpu temp goes up to 95 deg celcius when stress testing (no heatsink or fan installed at all) and the device reboots shortly afterwards. I ran `armbianmonitor -m` when stress testing and found out that some of the cores are not throttling. I examined the default trip point settings coming with the image in the file /boot/dtb/rockchip/rk3399-orangepi-4-lts.dtb: trips { cpu_alert0 { temperature = <0x14c08>; hysteresis = <0x7d0>; …

• 0

  Reputation Points

• 7 replies
• 7.6k views
• 1 follower

mimosius

September 17, 20242 yr

Hello folks! I was experimenting with all ARM images (Manjaro, Fedora, Arch, etc) i could find to test with the Orange Pi 4 LTS SBC board, and when i was about to return to armbian, it didnt boot anymore, not even from the SD card flashed with a proper image. I' currently using UART USB to TTL debug device to see whats happening with the board and it returns this: NOTE: [At the moment of this screenshot the board was with a SD card flashed with the default orange pi debian server image] Does anyone know how to reset this board and get it booting again from any ARM images? Would really appreciate any help on this…

• 0

  Reputation Points

• 5 replies
• 6.2k views

mimosius

September 16, 20242 yr

The overlay for the ap6275p seems to be missing in the new fresh 6.10 images. Haven't tried to compile a custom image yet (so might just be disabled in current build), but how could I help to bring this overlay to the official image?

• 0

  Reputation Points

• 1 reply
• 2.8k views
• 1 follower

Werner

September 15, 20242 yr

Hello, I'm using Armbian 24.5.3 Bookworm Minimal / IOT but there is no temperature in motd. When I inspect the normal datasources, it symlink to non-existent folder.

• 1

  Reputation Points

• 2 replies
• 4.3k views
• 1 follower

NixiElectra

September 15, 20242 yr

Hello, I tried to install the RTL8821CE card on Orange Pi 5 Plus, but only the Bluetooth is on, the wifi not working. Which driver i should use? I am using Armbian 24.2.1 Jammy with Linux 5.10.160-legacy-rk35xx here is the dmesg of admin@orangepi5-plus:~$ nmtui admin@orangepi5-plus:~$ dmesg | grep 8821 [ 5.588211] pci_bus 0003:30: root bus resource [mem 0x9c0000000-0x9ffffffff pref] [ 8.482106] rtw_8821ce 0002:21:00.0: enabling device (0000 -> 0003) [ 8.493940] rtw_8821ce 0002:21:00.0: Firmware version 24.11.0, H2C version 12 [ 8.534600] rtw_8821ce 0002:21:00.0: rfe 6 isn't supported [ 8.534719] rtw_8821ce 0002…

• 0

  Reputation Points

• 1 reply
• 3.1k views

ozacas

September 12, 20242 yr

I'd like to add hardware acceleration for my Orange PI 5 Plus, i've installed ` apt install -y clinfo` on the host (armbian) docker exec -it jellyfin /usr/lib/jellyfin-ffmpeg/ffmpeg -v debug -init_hw_device rkmpp=rk -init_hw_device opencl=ocl@rk ffmpeg version 6.0.1-Jellyfin Copyright (c) 2000-2023 the FFmpeg developers built with gcc 12 (Debian 12.2.0-14) configuration: --prefix=/usr/lib/jellyfin-ffmpeg --target-os=linux --extra-version=Jellyfin --disable-doc --disable-ffplay --disable-ptx-compression --disable-static --disable-libxcb --disable-sdl2 --disable-xlib --enable-lto --enable-gpl --enable-version3 --enable-shared --enable-gmp --enable-gnutls …

• 0

  Reputation Points

• 13 replies
• 8.7k views
• 2 followers

ozacas

September 12, 20242 yr

I'm getting the following errors when trying to upgrade rob@orangepi5:~$ uname -a Linux orangepi5 6.1.75-vendor-rk35xx #1 SMP Wed Aug 21 11:45:59 UTC 2024 aarch64 GNU/Linux rob@orangepi5:~$ sudo apt upgrade Reading package lists... Done Building dependency tree... Done Reading state information... Done You might want to run 'apt --fix-broken install' to correct these. The following packages have unmet dependencies: armbian-bsp-cli-orangepi5 : Depends: armbian-bsp-cli-orangepi5-current (= 24.8.2) but it is not installed E: Unmet dependencies. Try 'apt --fix-broken install' with no packages (or specify a solution). rob@orangepi5:~$ sudo apt --fix-broken install …

• 0

  Reputation Points

• 5 replies
• 5.8k views
• 1 follower

Igor

September 10, 20242 yr

I have installed the recently released `Desktop images with Armbian Linux v6.10` image (24.8.1, Debian Bookworm, with the Cinnamon desktop) on an OrangePi5 and I'm happy the HDMI support included has finaly enabled the video to my 1080p display. However, my previously supported WiFi adapter is not recognized in this version - it worked with the vendor (5.10) kernel which I used with last year's OrangePi5 image, but how it seems the driver is not installed with 6.10. The WiFi adapter is connected via USB and it's listed as Realtek Semiconductor Corp. RTL8812AU 802.11a/b/g/n/ac 2T2R DB WLAN Adapter. Now, there are a few DKMS/out-of-tree drivers that I could inst…

• 1

  Reputation Points

• 4 replies
• 7.7k views
• 2 followers

mitu

September 10, 20242 yr

Kodi on Orange Pi 5 with GPU Hardware Acceleration and HDMI Audio Huge thanks to user @roykon the Armbian forums for the directions on this in their various forum posts and Armbian forum user @amazingfate for maintaining the PPAs and software builds required for GPU acceleration. I have simply listed below, for the reference of others, the minimum Steps used to get Kodi running with GPU hardware acceleration (for x264/x265 decode) plus HDR auto switching and with HDMI Audio output*. (I am using the Orange Pi 5 with a Samsung 4K TV) *No instructions added yet for enabling HDMI passthrough. ** No instructions added yet for enabling HDMI CEC. …

• 1

  Reputation Points

• 210 replies
• 181.2k views
• 9 followers

compent

September 10, 20242 yr

hi, How to download armbian games？？

• 0

  Reputation Points

• 3 replies
• 3k views

lay

September 7, 20242 yr

I want to change the default display wallpaper, in order to be more nice!!! for "desktop gnome"： How to configure and appoint the default wallpaper for desktop display in build ??? Please help tell me the location！！！thank

• 0

  Reputation Points

• 1 reply
• 1.9k views

Werner

September 7, 20242 yr

Hello! First time poster, long time admirer. I've been unable to get ANY of the 6.10.x images to boot off SD card (Sandisk Extreme) for the Orange Pi 5 Plus. Specific images which are not working for me: Armbian_24.8.0-trunk.472_Orangepi5-plus_noble_edge_6.10.2_gnome-kisak_desktop.img.xz Armbian_24.5.5_Orangepi5-plus_noble_edge_6.10.1_gnome-kisak_desktop.img.xz Armbian_24.8.0-trunk.472_Orangepi5-plus_trixie_edge_6.10.2_minimal.img.xz Has anybody else had better luck?

• 0

  Reputation Points

• 12 replies
• 10.2k views

Avatar Ng

September 6, 20242 yr

May I ask where to add and place the background image？？ help.....

• 0

  Reputation Points

• 6 replies
• 3.7k views

Werner

September 5, 20242 yr

I created a deb package for my own application. How do I import it for compilation and installation?

• 0

  Reputation Points

• 1 reply
• 2.3k views

Werner

September 3, 20242 yr

I'm trying to install https://dl.armbian.com/orangepi5-plus/Bookworm_vendor_minimal in my Orange PI 5 Plus to the emmc but I've got a black screen after removing sd card.

• 0

  Reputation Points

• 2 replies
• 2.2k views
• 1 follower

Rdlop

September 2, 20242 yr